5801*B FOUNTAIN / 5801*B FOUNTAIN W/5803 CUSPIDOR
Halsey Taylor Owners Manual
12
See Fig. 7
4, 6, 19
5801 FOUNTAIN
25
See Detail A
9
See Fig. 5
13
24
5801 FOUNTAIN
W/O CUSPIDOR
3/8 Unplated
Copper Tube
20
24
26
5801 FOUNTAIN
WITH CUSPIDOR
To Cuspidor
DETAIL A
4, 22
12
1, 17
21
See Fig. 7
5803 CUSPIDOR
13
9
INSTALLER
Halsey Taylor Fountains are among the easiest to install Fountains
on the market today. To assure you install these models easily and
correctly, PLEASE READ THESE SIMPLE INSTRUCTIONS BEFORE
STARTING THE INSTALLATION. CHECK YOUR INSTALLATION FOR
COMPLIANCE WITH PLUMBING, ELECTRICAL, AND OTHER APPLICABLE CODES. After installation, leave these instructions with the
Fountain for future reference.
IMPORTANT
ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON
PAGE 1
97100C (Rev. D - 2/01)
97100C (Rev. D - 2/01)
DIMENSIONS
PAGE 2
LEGEND/LEYENDA/LÉGENDE
A = RECOMMENDED WATER SUPPLY LOCATION 3/8 O.D. UNPLATED COPPER TUBE CONNECT STUB 1-1/2 IN. (38 mm) OUT FROM WALL SHUT
OFF BY OTHERS
SE RECOMIENDA UBICAR EL TUBO CORTO DE CONEXIÓN AL TUBO DE COBRE SIN CHAPAR DE 3/8" DE DIÁM. EXT. A 1-1/2" (38 mm) FUERA
DE LA LLAVE DE PASO EN LA PARED COLOCADA POR TERCEROS.
EMPLACEMENT RECOMMANDÉ D'ALIMENTATION EN EAU PAR TUBE EN CUIVRE NON PLAQUÉ DE 3/8 PO. (9,5 mm) D.E. CONNECTANT UNE
TUYAUTERIE DE 1-1/2 PO. (38 mm) DEPUIS LE ROBINET D'ARRÊT FOURNI PAR D'AUTRES.
B = RECOMMENDED LOCATION FOR WASTE OUTLET 1-1/2” O.D. DRAIN
UBICACIÓN RECOMENDADA PARA EL DRENAJE DE SALIDA DE AGUA, DE 1-1/2” DE DIÁMETRO.
EMPLACEMENT RECOMMANDÉ POUR LE DRAIN DE D.E. 1-1/2" DE SORTIE D’EAU.
C = WALL SCREW HOLES
AGUJEROS DE TORNILLOS DE PARED
TROUS DE VIS DU MUR
FIG. 1
ROUGH-IN
5801*B FOUNTAIN / 5801*B FOUNTAIN W/5803 CUSPIDOR
5801*B FOUNTAIN / 5801*B FOUNTAIN W/5803 CUSPIDOR
FIG. 2
INSTALLATION INSTRUCTIONS
1. Prepare the wall cutout opening(s). Refer to Wall Cutout Detail
(See Fig 2).
2. Prepare waste connection(s) and water supply hookup
connection. Refer to roughin drawing for location details
(See Fig. 1).
NOTE: Access to the rear of the fountain is desirable to ease
installation. If rear access is not obtainable an access panel
(furnished by others) should be installed below the fountain.
3. Install the fountain hanger bracket(s) to the upper edge of the
wall cutout. Remove bottom cover plates from the fountain.
Save the cover plates and screws for reinstallation.
4. Install the basin. Place the upper edge of the basin above the
hanger in the wall frame. Slide the basin down until it engages
the hanger. Be sure the basin is firmly engaged before releasing
it. Secure the bottom of the fountain to the wall frame. If
fountain is used with the 5803 Cuspidor repeat above steps.
NOTE: SCREWS FOR ATTACHING THE FOUNTAIN HANGER
BRACKET AND BASIN ARE NOT INCLUDED.
FIG. 3
5. Connect waste line traps to the fountain (and cuspidor if
required). Connect water supply line service stop to the water
inlet line on the 5801 Fountain. Fountain is supplied with a 3/8"
unplated copper water hookup line with a strainer. The fountain
must be connected through the strainer to elminate damage to the
water regulator on/off control.
NOTE: WASTELINE TRAP(S) AND SERVICE SUPPLY STOPS
ARE NOT INCLUDED.
6. 5803 Cuspidor only. Connect outlet of the check valve to the
inlet line, to the sprayer head, on the 5803 Cuspidor. Check
valve flow direction must be as shown for correct operation.
7. Open service stop and operate push button to purge air from
system. Check thoroughly for leaks. Check stream height from
bubbler. Stream height is factory set at 45-50 PSI. If supply
pressure varies greatly from this, remove items 14 and 15 and
adjust screw on regulator (item 23) see figure 5. Clockwise
adjustment will raise stream and CCW adjustment will lower
stream height. For best adjustment stream height should be
approximately 1-1/2" (38mm) above the bubbler guard. (See
Fig. 9).
8. Assemble cover plate to bottom of fountain with screws supplied.
PAGE 3
FIG. 4
97100C (Rev. D - 2/01)
5801*B FOUNTAIN / 5801*B FOUNTAIN W/5803 CUSPIDOR
ITEMIZED PARTS LIST
ITEM NO.
PART NO.
5801 FTN
PART NO.
5801 W/CUSP
PART NO.
5803 CUSP
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
NS
100147140560
15005C
100322740560
100352940560
110346220550
160270508640
160346108640
160346308640
102639931920
170639442830
23044C
40048C
40089C
40169C
50986C
51546C
60119C
61313C
62304C
55996C
101637451550
401495443730
100147140560
15005C
100322740560
100352940560
102688531550
110346220550
160270508640
160346108640
160346308640
102639931920
170639442830
23044C
40048C
40089C
40169C
50986C
51546C
60119C
61313C
66209C
55996C
75494C
101637451550
401495443730
100115824740
100147140560
15005C
100322740560
100352940560
110346220550
160270508640
160346108640
160346308640
161637308640
400825342830
400952143730
411564208640
601563851550
610810751640
101637451550
401495443730
DESCRIPTION
Gasket 1-1/4 I.D.
Gasket
Nut - Retainer
Gasket - Black
Gasket - Slipnut
Suppressor - Surge
Locknut - 1 1/2 x 11 1/2
Strainer Plate - Chrome
Tailpiece - 1 1/2 OD x 4
Slipnut - 1 1/2
Drain Plug - Chrome
Basin
Bottom Cover
Button - Chrome
Cover Nut - Chrome
Hex Nut - Chrome
Nut
Regulator Holder
Bubbler - Chrome
Tube - Cu 1/4 x 5.00 Lg
Tube Assy
Cuspidor Head
Regulator
Tube Assy - Bubbler
Strainer
Check Valve - 3/8
Ring - Friction
Basin Hanger
15
3
14
23
18
16
FIG. 5
8
11
OPERATION OF QUICK CONNECT FITTINGS
Cooler is provided with lead-free connectors which utilize an o-ring water seal. To remove tubing
from the fitting, relieve water pressure, push in on the gray coolar while pulling out on the tubing.
To insert tubing, push tube straight into fitting until it reaches a positive stop, approximately 3/4".
Simply Push In Tube
To Attach
A
Tube Is Secured In
Position
B
Push In Collet To
Release Tube
2
7
5
27
C
Insert tube to a positive stop
approximately 3/4 of an inch
Pushing Tube In Before
Pulling It Out Helps To
Release Tube.
10
FIG. 6
FIG. 7
3/8" O.D. UNPLATED
COPPER TUBE CONNECT
COLD WATER SUPPLY
1/4" O.D. TUBE
WATER INLET
TO COOLER
NOTE: WATER FLOW
DIRECTION
BUILDING WATER
INLET
SERVICE STOP
(NOT FURNISHED)
FIG. 8
CORRECT STREAM HEIGHT
FIG. 9
2222 CAMDEN COURT
OAK BROOK, IL 60523
630.574.3500
PRINTED IN U.S.A.
FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.323.0620
97100C (Rev. D - 2/01)
PAGE 4