Technical Data Sheet - Submersible drainage pump XJ 110

Submersible Drainage Pump
XJ 110
Electric submersible pump.
Maximum submergence: 20 m. Protection class IP 68.
Max temperature of pumped medium at max power input and
continuous duty 40 ºC.
Max medium density 1100 kg/m3. pH of the pumped medium 5-8.
Strainer hole: 7.5 x 22 mm. Max number of starts 30/hour.
XJ 110 ND
XJ 110 ND AT*
XJ 110 HD
XJ 110 HD AT*
60
XJ110-ND-AA/HD-AA 50Hz
Specification
m
HD
40
ND
Medium head, 3-phase
Medium head, 3-phase
High head, 3-phase
High head, 3-phase
20
*AquaTronic: Built-in electronic pump control.
0
0
10
0
Electric Motor
20
50
30
100
40
50
150
60 l/s
200 m3/h
3-phase squirrel-cage induction motor, 50 Hz.
Service factor 1.1. Class F insulation.
Motor rating P2: 11.8 kW. 2 pol. Speed: 2920 rpm.
ŋ: 89.8 (50 %), 90.9 (75 %), 90.8 (100 % load)
230
400
500-550
690
1000
37.4
21.5
17.2
12.5
8.6
812
Voltage, V
Nominal current, A
XJ 110 AT: Direct on line start (DOL 500-550 V) with built in
AquaTronic unit, which automatically adjusts phase order by dual
contactors, ensuring correct motor rotation.
Soft start (400 V) is built in with the AquaTronic unit, where three
thyristors reduces start current to three times the nominal current.
Here two relays ensure correct motor rotation.
The AquaTronic unit monitors motor temperature, by use of NTC
thermistors built into stator windings, and stops the motor at high
temperature. It will also stop the motor at high amperage or if a
phase is missing.
max** 476
Starting Method and Motor Protection
Ø 285
max** 440
max** 466
mm
** Max measurement based on largest discharge size.
Shaft Seal
XJ 110: Direct on line start with built in contactor. Pumps to be used
with VFD or 1000 V must have terminal block instead of contactor.
Thermal switches (140 °C, ±5) built into the stator windings are
connected to the contactor and stop the pump at high temperature.
Double mechanical seal in oil bath.
Primary seal: Silicon carbide on silicon carbide.
Secondary seal: Silicon carbide on carbon.
Power Cable
Upper bearing: Single-row deep groove ball bearing.
Lower bearing: Double angular contact ball bearing.
20 m type S1BN8-F (standard cable):
4 x 6 sq.mm. (230 V)
4 x 4 sq.mm. (400 V, 500-550 V)
4 x 2.5 sq.mm. (690 V)
20 m type NSSHÖU.../3E (heavy duty cable):
3x6+3x6/3E+3x1.5 (3 control cables included) (230-400 V terminal
block)
3x2.5+3x2.5/3E+3x1.5 (3 control cables included) (500-1000 V
terminal block)
3x6+3x6/3E+3x1.5 (230-400 V)
3x2.5+3x2.5/3E (500-550 V, 690 V)
Bearings
Discharge Connections
3” (standard HD), 4” (standard ND), 6” hose connections.
3”, 4”, 6” G/B.S.P. threaded connections.
Weight
81 kg (without cable)
Options and Accessories
AquaPlug. Level sensor. Service data kit. Zinc anodes.
Surface protection coating. Series connection. Floatation system.
Discharge connection accessories and hose.
Pump control
Features
XJ 110
XJ 110 AT
AT
AT
+ Level Sensor
AT
+ AquaPlug
AT + AquaPlug
+ Level Sensor
Service Data Kit
Read out
Run mode
X
X
X
X
X
Integrated start equipment
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Motor protection high amp
X
X
X
X
X
Protection against missing phase
X
X
X
X
X
Automatic direction of rotation
Motor protection high temp
X
Level control
X
X
Dry run protection
X
X
Automatic restarting
X
X
Stop mode
X
E-mode (Automatic stop/run)
X
X
Indication of water in oil
X
X
X
Indication of low motor insulation
X
X
X
Indication of high or low voltage
XX
XX
X
Indication of high temperature
XX
XX
X
Indication of high amp
XX
XX
X
Indication of phase unbalance
XX
XX
X
X
X
X
USB cable connection
X
X
Crash log (10 latest)
X
Documentation (spare part list, workshop
manual)
X
XX = Fault indication when pump is automatically stopped to protect the motor.
Materials
Description
Material
EN
ASTM
Castings
Aluminium
EN 1706:AC-43100
ASTM AlSi10mg
Strainer / Handle
Stainless steel
10088:X5CrNi18-10 (1.4301)
AISI 304
Rotor shaft
Stainless steel
10088:X20Cr13 (1.4021)
AISI 420
Impeller / Wear ring
White cast iron
EN-GJN-HV600(XCr23)
ASTM A 532: Alloy III A
Fasteners
Stainless steel
10088:X5CrNiMo 17122 (1.4401)
AISI 316
Wear parts / O-rings
Nitrile rubber
Coating
2 component epoxy paint 80 µm
www.sulzer.com
XJ 110 50Hz en (12.2015), Copyright © SULZER Ltd. 2015
This document does not provide a warranty or guarantee of any kind. Please contact us for a description of the warranties and guarantees offered with our products. Directions for
use and safety will be given separately. All information herein is subject to change without notice.