EVO2 LED
LIGHTS FOR FIBREGLASS
& VINYL POOLS
INSTALLATION INSTRUCTIONS
INSTALLER
– READ ENTIRE INSTRUCTION SHEET BEFORE
PROCEEDING TO INSTALL.
POOL OWNER
– PLEASE KEEP THESE INSTRUCTIONS FOR
FUTURE REFERENCE.
PLEASE NOTE
THESE INSTALLATION INSTRUCTIONS APPLY TO
AQUA-QUIP EVO2 LED LIGHTS FOR FIBREGLASS & VINYL POOLS ONLY.
Fibreglass and Vinyl Pools
Evo2 LED Pool Lights for Fibreglass and Vinyl Pools fit
through a 4” (102mm) hole and are supplied with the
Quick Connect Cable pre-fitted to the pool light. The pool
light is supplied fitted inside the fibreglass/vinyl housing.
The housing is factory fitted with 1 metre of cable wound
up inside. Supplied with lock nut and gaskets, ready to
install. Stainless Steel Trim Ring Kits are available as an
optional extra.
Included in the package are the following items:
Optional
Stainless Steel
Dress Ring
(not included as
standard)
Cable
Locking Ring
Rubber Gasket
Cork Gasket
Housing
Evo2 LED/Aqua Star Halogen Flush Mounted
Pool Light – Fibreglass & Vinyl Pools
DIMENSIONS
(mm)
FIBREGLASS
HOUSING
D
F
C
B
A
EVO2
H
LIGHTS
E
Standard FOR
FIBREGLASS
&
VINYL
G
Stainless Steel
POOLS
–
INSTALLATION
A
195
B
144
C
100 max
D
13
E
23
F
144
G
25
H
167
INSTRUCTIONS
1
EVO2 LED
LIGHTS FOR FIBREGLASS
& VINYL POOLS
AQUA-QUIP EVO2 LED INSTALLATION INSTRUCTIONS FOR FIBREGLASS & VINYL POOLS
1 Drill a 102mm (4") diameter hole in the pool wall where the light is to be located – the centre of
the hole should not be more than 500mm below the top of the finished pool coping. Choose
a flat surface. If pool is vinyl lined – first cut a similar hole in vinyl using knife before hole is cut
through steel panel. Contact Aqua-Quip for suppliers of 102mm hole saws.
2 Remove any debris from around the hole cut. Feed the light cable through the hole in the pool
wall, fit the pool light Housing into the hole, and push the white Rubber Gasket and Housing
up against the pool wall. Apply a thin bead of waterproof silicone sealant between white rubber
gasket and pool wall.
3 Behind the pool, pass the cable through the Cork Gasket and Locking Ring provided.
4 Fit the Cork Gasket over the thread on the rear of the Housing and push it up against the rear
of pool wall.
5 Ensure the threads on the Housing and Locking Ring are clean of sand and debris.
6 Screw the Locking Ring onto the Housing and tighten it up against the Cork Gasket using a
strap wrench or similar.
7 Use Polished Stainless Steel Trim Ring if required.
8 Only turn Evo2 LED Pool Light on when completely submerged under water.
TECHNICAL SPECIFICATIONS EVO2 LED FLUSH MOUNTED POOL LIGHTS
Nominal Supply Voltage: Voltage Tolerance:
Protection Rating: Temperature Range: Power Consumption:
Power Consumption:
Lamp Life:
Light Output (typical):
Fault Protection:
12V AC 50/60 Hz
+20%, -20%
IPX8 (to 2.0m depth)
-10°C ~ +40°C water temperature
White, blue and green = 8 VA
Spectrum III Multi Colour = 16 VA maximum
>50,000 hours
White-550 lumens, blue-180 lumens, green-500 Lumens
Power-cycle “run dry” thermal cut-out. Voltage transient clamping.
IEvo2 LED Lights must only be operated underwater as they are water-cooled.
ELECTRICAL CONNECTION AND
OPERATION
TRANSFORMERS
Diagram 1 – Transformers
• Install Light(s) and Transformer(s) in accordance
with AS/NZS 3000:2007 as amended.
• Aqua-Quip’s extra low voltage Transformers have
either 2 or 4 secondary outputs, each being 12v
50VA, refer to Diagram 1.
• Dimming of Evo2 LED Fixed Colour Lights
(i.e. white, blue and green) is possible.
Aqua-Quip recommends the HPM Leading Edge
Dimmer Cat. 200L. Evo2 Multi-Colour LED Lights
cannot be dimmed.
APL504 and
APL514 run up to
4 x 50va lights.
APL502 and
APL 512 run up to
2 x 50va lights.
WARNING
Never stare directly at LED Pool Lights.
Prolonged direct exposure can cause eye damage.
• If your lights are Evo2 Multi-Colour, then see
included “LED Programming Instructions”.
COPYRIGHT AUTOMATIC POOL CLEANERS (AUSTRALIA) PTY LTD
EIFM2p_0911
Automatic Pool Cleaners (Australia) Pty Ltd
40 Percy Street, Auburn NSW 2144
Ph: 02 9643 8338 Fax: 02 9643 8448
www.aquaquip.com.au
2
EVO2
LIGHTS
FOR
FIBREGLASS
&
VINYL
POOLS
–
INSTALLATION
INSTRUCTIONS