RESS
TO
R ING
INSTALLATION • MOUNT KEYPAD
NOTE: For optimal range performance, mount the receiver to an external wall that is close to the gate operator. DO NOT MOUNT TO METAL.
2
1
WIRELESS GATEBELL KEYPAD
LEARN
®
MODEL WGB315 315 MHz Security✚
PRESS
® R TO
ING
MODEL WGB315INDR 315 MHz Security✚
®
MODEL WGB315KYPD 315 MHz Security✚
PRESS
TO
R ING
P R ET OS
S
RING
PRESS
TO
PRESS
RING
CARTON INVENTORY
PRESS
KEYPAD MOUNTING
(For reference only)
TO
3
TO
4
Lift
†
RReceiver
ING
R ING
Keypad*
PRESS
R ING
Drywall Anchors (2)
†
Screws (4)*†
Bottom
Mounting
Hole
Remote Control, Receiver, Power Adapter, Drywall Anchors and 2 Screws provided
in model WGB315INDR.
INSTALLATION • MOUNT RECEIVER
LEARN
4 1/4"
(10.8 cm)
Battery
* Keypad and 2 Screws provided in model WGB315KYPD.
Battery Cover
Remove battery cover and battery.
Determine location for keypad. Mark
the bottom mounting hole.
TABLETOP MOUNTING
For the top mounting screw, mark 4
1/4" (10.8 cm) up the centerline from
the bottom of the keypad. Drill 1/8"
pilot holes for top and bottom screws.
See keypad mounting reference.
6
5
1
Top Mounting Hole
LEARN
TO
†
Remove foam spacer on underside of
keypad cover. Check range before
installing. Using two people, hold the
keypad and receiver in the desired locations.
Make sure the keypad rings the gatebell
when pressed. If no chime is heard, repeat
test using a new location for the receiver.
†
R ING
Power Adapter
PRESS
TO
RING
PRESS
TO
R†ING
Remote Control
PRESS
Program remote control to the gate
operator radio receiver. Refer to your
gate operator manual for programming
instructions.
TO
LEARN
LEA
LEARN
LEARN
LEARN
LEARN
LEARN
LEARN
LEARN
LEARN
Insert remote control and power
adapter into receiver. Plug into outlet.
Install top mounting screw, allowing
1/8" (3.2 mm) to protrude above surface.
Position keypad on screw head and adjust
for snug fit.
LEARN
LEARN
Secure keypad with bottom screw, using
care to avoid cracking plastic housing.
LEARN and slide battery cover
Reinstall battery
up and snap it into place. Close cover.
LEARN
LEARN
LEARN
L
LEARN
INSTALLATION • MOUNT RECEIVER
WALL MOUNTING
2
1
LEARN
4
Wall
3
Wall
5
6
LEARN
2 1/8" (5.4 cm)
Drywall
Anchors
Screw
Mounting Holes
Screw antenna into receiver. Determine
location for indoor receiver.
Mark and drill pilot holes using 1/4"
drill bit.
Insert drywall anchors.
Install mounting screws, allowing
1/8" (3.2 mm) to protrude above
surface.
OPERATIONAL TEST
NOTE: Two people will be needed to properly test the gate doorbell.
2
LEARN
Plug power adapter into receiver.
Plug into outlet.
KEYPAD TO INDOOR RECEIVER
3
1
STOP
LEARN
RESS
P TO
RING
Push “Press to Ring” on the
keypad cover.
Insert remote control into receiver.
PROGRAMMING
LEARN
1
Position receiver on screw heads.
2
Learn Button
S
S
E
R
P O
LEARN
T
The gatebell will ring.
Press remote control button to open
the gate.
The included keypad is learned
to the receiver at the factory.
Follow the next steps to learn
replacement or additional
keypads only.
RING
Press and release the learn button
on the back of the indoor receiver.
Push “Press to Ring” on the
keypad cover within 30 seconds.
Repeat operational test to verify.
CAUTION: Pressing the learn button for more than 6 seconds will clear all the learned keypads.
The keypad can also be programmed to the gate operator using a 4-digit PIN entry code. Refer to your gate operator manual.
THE KEYPAD BATTERY
Top Cover
To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.
Bottom Mounting Hole
9V Battery
Battery Cover
114A3447C
The battery should produce power for at least one year.
Replace when the keypad illumination becomes dim or it
doesn’t stay on after a keystroke.
Dispose of old battery properly.
FOR SERVICE DIAL OUR TOLL FREE NUMBER: 1-866-826-4943
© 2008, The Chamberlain Group, Inc.
All Rights Reserved