User's Manual Facia Plate Metra 95-8202 for Toyota Scion (044)361-05-06 ICQ:495-089-192

(044)361-05-06
ICQ:495-089-192
(067)469-02-12
ICQ:613-211-859
(099)048-99-03
(093)672-77-76
User's Manual
Facia Plate Metra 95-8202 for Toyota Scion
In the online store Winauto you also can buy Facia Plate Metra 95-8202 Toyota Scion. Delivery in Kyiv and throughout
Ukraine with payment upon receipt!
winauto.ua
Sale - Car Receivers - Facia Plates - Head Units - Car TVs and Monitors - Antennas - Car Audio - DVR - GPS Navigation - Trip Computers - Car
Alarm Systems - Mechanical Locking - Parking Systems - Car Cameras - Xenon and Lights - Established Optics - Tuning - Car Heating and Cooling Sound Marine and Electronics - Car Accessories - Isolation - Installation Components - Batteries, Power - Oils and Fluids -
Интернет-магазин автозвука и автотоваров Винавто
INSTALLATION INSTRUCTIONS FOR PART 95-8202
APPLICATIONS
to
.u
a
Toyota
Rav 4 2001-05
MR2 Spider 2000-03
Celica 2000-05
Echo 2000-05
Highlander 2001-07
Matrix 2005-09/ Matrix 2009 (With Factory Navigation)
4 Runner (Excluding Limited) 2003-09
Tundra 2003-06
Sequoia 2003-07
FJ Cruiser 2007-up
Yaris 2007-2010
Scion TC 2005-up / XA 2004-06 / XB 2004-up / XD 2008-10
KIT FEATURES
in
au
95-8202
KIT COMPONENTS
A) DDIN Trim plates
A
w
• DDIN Head Unit Provision
• Stacked ISO DIN Head Unit Provision
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Wiring Harness:
• 70-1761 Toyota harness 1987-up
• TYT0-01 Toyota amp harness 2003-up
Antenna Adapter:
• Not required
TOOLS REQUIRED:
Cutting Tool • Phillips Screwdriver • Socket Set • Grinder
1-800-221-0932
www.metraonline.com
© COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION
Интернет-магазин автозвука и автотоваров Винавто
95-8202
TABLE OF CONTENTS
w
in
au
to
.u
a
Dash Disassembly
Toyota Rav 4 2001-2005............................................................... 1
Toyota MR2 Spyder 2000-2003 .................................................... 2
Toyota Celica 2000-2005 ............................................................. 3
Toyota Echo 2000-2005 ............................................................... 4
Toyota Highlander 2001-2007 ..................................................... 5
Toyota Matrix 2005-2008 ............................................................. 6
Toyota Matrix 2009 (With Factory Navigation)............................. 7
Toyota 4 Runner (Excluding Limited) 2003-2009 ......................... 8
Toyota Tundra 2003-2006 ............................................................. 9
Toyota Sequoia 2003-2006 ..........................................................10
Toyota FJ Cruiser 2007-up...........................................................11
Yaris 2007-2010 ..........................................................................12
Scion XA 2004-2006 ....................................................................13
Scion XB 2004-2007....................................................................14
Scion XB 2008-up........................................................................15
Scion TC 2005-2010 ...................................................................16
Scion TC 2011-up ........................................................................17
Scion XD 2008-2010....................................................................18
Kit Assembly
Double DIN Head Unit Provision.................................................. 19
Stacked ISO DIN Head Unit Provision ......................................... 19
Final Assembly ............................................................................20
Интернет-магазин автозвука и автотоваров Винавто
95-8202
DASH DISASSEMBLY
TOYOTA RAV 4 2001-2005
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
2
Unclip and remove side panel from
both sides of radio and climate
controls. Figure A)
3
Remove (4) Phillips screws securing
the radio/climate control trim panel.
(Figure B)
to
.u
1
a
A
Remove (4) 10 mm bolts securing the
radio. (Figure C)
5
Unplug and remove radio.
6
Remove factory brackets from radio.
Retain brackets for use during kit
assembly.
w
in
au
4
B
7 Continue to kit assembly.
C
1
Интернет-магазин автозвука и автотоваров Винавто
95-8202
DASH DISASSEMBLY
TOYOTA MR2 SPYDER 2000-2003
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
2
Unsnap the lower trim piece from
each side of the dash console and
remove (2) Phillips screws exposed in
each cavity. Remove the upper trim
piece from each side of the console.
(Figure A)
3
Remove the climate control knobs
and (2) Phillips screws exposed.
Remove the climate control trim
bezel. (Figure A)
4
Remove the ashtray and (1) 10 mm
bolt exposed. Unclip the ashtray trim
bezel and remove. (Figure A)
w
in
au
to
.u
1
a
A
5 Unclip the radio trim bezel, remove
(4) Phillips screws securing the unit
and disconnect the wiring.
6 Remove factory brackets from radio.
Retain brackets for use during kit
assembly.
7 Continue to kit assembly.
2
Интернет-магазин автозвука и автотоваров Винавто
95-8202
DASH DISASSEMBLY
TOYOTA CELICA 2000-2005
A
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
2
Unclip and remove the gear shifter
trim bezel and remove (2) Phillips
screws exposed below the climate
controls. (Figure A)
3
Pull off climate control knobs and
remove (2) Phillips screws exposed.
(Figure A)
4
Unclip the climate control/factory
radio trim bezel and remove.
(Figure A)
5
Remove (4) 10 mm screws securing
the factory head unit and disconnect
the wiring.
w
in
au
to
.u
a
1
6 Remove factory brackets from radio.
Retain brackets for use during kit
assembly.
7 Continue to kit assembly.
3
Интернет-магазин автозвука и автотоваров Винавто
95-8202
DASH DISASSEMBLY
TOYOTA ECHO 2000-2005
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
2
Remove the climate control knobs
and (2) Phillips screws exposed.
Unclip and remove the climate control trim bezel. Depress the side
clips securing the climate control
panel and move the panel to access
(2) Phillips screws from the top of
the factory radio brackets. (Figure A)
3
Remove the ashtray. Unclip and
remove the radio trim bezel. Remove
(2) Phillips screws from the bottom
of the radio brackets and disconnect
the wiring.
4
Remove factory brackets from radio.
Retain brackets for use during kit
assembly.
w
in
au
to
.u
1
a
A
5 Continue to kit assembly.
4
Интернет-магазин автозвука и автотоваров Винавто
95-8202
DASH DISASSEMBLY
TOYOTA HIGHLANDER 2001-2007
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
2
Pull and remove dash panel from
radio and climate controls. Tip: There
are 8 clips. (Figure A)
3
Remove (6) 10 mm bolts from radio
and climate controls assembly.
(Figure B)
to
.u
1
a
A
Remove assembly and disconnect
the wiring.
5
Remove (8) Phillips bolts and (4) Phillips
screws to separate brackets from assembly. Retain brackets for use during
kit assembly. (Figure C)
6
Continue to kit assembly.
w
in
au
4
B
C
5
Интернет-магазин автозвука и автотоваров Винавто
95-8202
DASH DISASSEMBLY
TOYOTA MATRIX 2005-2008
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
2
Unclip the bottom edge of the radio
trim panel then lift up and out to
remove. (Figure A)
3
Remove (4) 10 mm bolts securing
the factory radio. (Figure B)
to
.u
1
a
A
w
in
au
B
6
Интернет-магазин автозвука и автотоваров Винавто
95-8202
DASH DISASSEMBLY
TOYOTA MATRIX 2009
(WITH FACTORY NAVIGATION)
1
A
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
PASSENGER
Unclip and remove the radio trim
panel including the a/c vent.
(Figure A)
3
Remove (4) 10 mm bolts securing
the factory radio. Unplug and remove
the radio. (Figure B)
to
.u
2
a
SECURITY
w
in
au
B
7
4 5
0
12 3
A/C
Интернет-магазин автозвука и автотоваров Винавто
95-8202
DASH DISASSEMBLY
TOYOTA 4 RUNNER 2003-2009
(EXCLUDING LIMITED)
4
5
6
7
Unsnap and remove trim covers from
around center console pocket edge
at front and rear of console.
Unsnap and remove center console
cover. (Figure A)
B
a
3
Unsnap trim ring from around ignition
key cylinder.
Remove (1) 10 mm bolt from bottom
right of panel below steering column.
Unsnap panel and pull away to gain
access behind panel. (Figure B)
to
.u
2
A
Disconnect the negative battery terminal to prevent an accidental short
circuit.
Unsnap and remove trim from around
shifter.
in
au
1
C
w
Remove (1) 10 mm bolt on bottom
left of center panel behind panel
below steering column. (Figure B)
8 Remove (1) 10 mm bolt beneath climate control behind pocket door.
Unsnap and remove climate control.
(Figure C)
9 Remove (2) 10 mm bolts beneath
radio behind climate controls.
10 Unsnap and remove entire center
panel around radio. (Figure D)
11 Remove (2) 10 mm bolts securing
radio.
12 Unplug and remove radio.
13 Remove factory brackets from radio.
Retain brackets for use during kit
assembly.
14 Continue to kit assembly.
D
8
Интернет-магазин автозвука и автотоваров Винавто
95-8202
DASH DISASSEMBLY
TOYOTA TUNDRA 2003-2006
1
2
3
A
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
Remove the (3) climate control knobs by
pulling straight outward. (Figure A)
Remove (3) Phillips screws from
behind knobs. (Figure A)
to
.u
B
Unclip and remove entire trim panel.
(Figure C)
in
au
5
a
4 Position vents facing upward and
remove (1) Phillips screw from each
A/C vent. (Figure B)
6 Remove (4)10 mm bolts to remove
radio. (Figure D)
w
7 Unplug and remove radio.
8 Remove factory brackets from radio.
Retain brackets for use during kit
assembly.
9 Continue to kit assembly.
C
D
9
Интернет-магазин автозвука и автотоваров Винавто
95-8202
DASH DISASSEMBLY
TOYOTA SEQUOIA 2003-2006
A
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
2
Position vents facing upward and
remove (1) Phillips screw from each
A/C vent. (Figure A)
3
Unclip and remove entire radio trim
panel including climate controls.
(Figure B)
to
.u
a
1
B
Remove (4) 10 mm bolts to remove
radio. (Figure C)
5
Unplug and remove radio.
6
Remove factory brackets from radio.
Retain brackets for use during kit
assembly.
7
Continue to kit assembly.
w
in
au
4
C
10
Интернет-магазин автозвука и автотоваров Винавто
95-8202
DASH DISASSEMBLY
TOYOTA FJ CRUISER 2007-UP
A
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
Remove two Phillips screws from
bottom part of side trim panels.
Figure A)
2
Using a panel removal tool, carefully
remove the side trim panels.
(Figure B)
4
Remove (2) Phillips screws from radio
trim panel. (Figure C)
5
Using panel removal tool, carefully
remove radio trim panel. (Figure D)
6
Remove (4) 10 mm bolts securing
the radio.
7
Unplug and remove radio.
8
Remove factory brackets from radio.
Retain brackets for use during kit
assembly.
9
Continue to kit assembly.
to
.u
3
a
1
w
in
au
B
C
D
11
Интернет-магазин автозвука и автотоваров Винавто
95-8202
DASH DISASSEMBLY
YARIS 2007-2010
A
3
4
Unclip the Instrument trim Panel
surrounding the Speedometer and
gauges. (Figure B)
a
2
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
Unclip the bottom trim panel located
underneath the A/C Controls.
Figure A)
Unclip the two side trim panels that
surround the A/C Controls and Radio.
(Figure A)
to
.u
1
B
Unclip the Radio/AC Vents trim
Panel.(Figure B)
6
Remove (4) Phillips screws securing
radio. (Figure C)
7
Unplug and remove radio.
8
Remove (4) Phillips screws securing
factory brackets on each side of the
radio and remove brackets. Retain
brackets for use during kit assembly.
(Figure D)
9
Continue to kit assembly.
w
in
au
5
C
D
12
Интернет-магазин автозвука и автотоваров Винавто
95-8202
DASH DISASSEMBLY
SCION XA 2004-2006
A
Disconnect the negative battery terminal
to prevent an accidental short circuit.
2
Pull outward on the (3) climate control
knobs and remove. (Figure A)
3
Remove (2) Phillips screws from behind
the outer two climate knobs. (Figure B)
4
Unsnap and remove the trim pieces on
each side of the climate control/ashtray/pocket assembly. (Figure C)
5
Remove (2) phillips screws from the
bottom of the climate control/radio trim
panel and unsnap and remove the entire
panel. (Figure D)
B
in
au
to
.u
a
1
Remove (4) Phillips screws to remove
the factory radio.
7
Remove factory brackets from radio.
Retain brackets for use during kit
assembly.
w
6
C
D
8 Continue to kit assembly.
13
Интернет-магазин автозвука и автотоваров Винавто
95-8202
DASH DISASSEMBLY
SCION XB 2004-2007
A
Disconnect the negative battery terminal
to prevent an accidental short circuit.
2
Pull outward on the (3) climate control
knobs and remove. (Figure A)
3
Remove (2) Phillips screws from behind
the outer (2) knobs. (Figure B)
4
Unsnap and remove the entire panel
surrounding the climate controls and
the radio. (Figure C)
5
Remove (4) Phillips screws to remove
the factory radio.
a
1
in
au
to
.u
B
w
6 Remove factory brackets from radio.
Retain brackets for use during kit
assembly.
7 Continue to kit assembly.
14
Интернет-магазин автозвука и автотоваров Винавто
95-8202
DASH DISASSEMBLY
SCION XB 2008-UP
A
Unclip and remove the trim panel
around the radio including the a/c vents.
(Figure A)
2
Unclip and remove the trim panel at the
bottom edge of the dash cavity.
(Figure B)
3
Remove (4) 10 mm bolts securing the
radio. (Figure C)
to
.u
B
w
in
au
Continue to kit assembly.
a
1
C
15
Интернет-магазин автозвука и автотоваров Винавто
95-8202
DASH DISASSEMBLY
SCION TC 2005-2010
Disconnect the negative battery terminal to prevent an accidental short circuit.
2
Unsnap trim from around shifter (not
necessary to be removed). (Figure A)
3
Unclip and remove panel from around
radio. (Including climate controls and
radio door). (Figure B)
4
Remove (2) 10 mm nuts from the top
mounting locations and (2) 10 mm bolts
from the bottom mounting locations to
remove the radio. (Figure C)
B
in
au
to
.u
1
a
A
w
5 Remove factory brackets from radio.
Retain brackets for use during kit
assembly.
6 Continue to kit assembly.
C
16
Интернет-магазин автозвука и автотоваров Винавто
95-8202
DASH DISASSEMBLY
SCION TC 2011-UP
A
Disconnect the negative battery terminal to prevent an accidental short circuit.
2
Unclip and remove the radio trim panel.
(Figure A)
3
Remove (4) 10 mm bolts securing the
radio. (Figure B)
a
1
4 Remove factory brackets from radio.
Retain brackets for use during kit
assembly.
to
.u
w
in
au
5 Continue to kit assembly.
B
17
Интернет-магазин автозвука и автотоваров Винавто
95-8202
DASH DISASSEMBLY
SCION XD 2008-2010
Disconnect the negative battery terminal to prevent an accidental short circuit.
2
Unclip radio trim panel. Unplug and
remove panel. (Figure A)
3
Remove (4) Phillips screws securing
the radio. Unplug and remove radio.
(Figure B)
in
au
Remove factory brackets from radio.
Retain brackets for use during kit
assembly. (Figure C)
Continue to kit assembly.
w
4
B
to
.u
1
a
A
C
18
Интернет-магазин автозвука и автотоваров Винавто
95-8202
KIT ASSEMBLY
A
NOTE: For all Scion TC and XA you will
need to cut off the front upper section of
the DDIN trim plates, as shown by dotted
lines labeled “A” in (Figure A).
For the 2001-2006 Toyota Rav 4, the
2001-2006 Toyota Highlander, and the
2003-2006 Toyota Sequoia/Tundra you
will need to cut off the rear section of
the DDIN trim plates, as shown by dotted
lines labeled “B” in (Figure A).
For all other vehicles skip to Step 1.
A
A
B
a
B
to
.u
DOUBLE DIN HEAD UNIT PROVISION
B
Attach the factory mounting brackets
and the 95-8202 DDIN trim plates to
the DDIN head unit with the screws
supplied with the unit. (Figure B)
NOTE: Remove locating pins from factory brackets with grinder.
w
in
au
1
STACKED ISO HEAD UNIT PROVISION
C
1
Attach the factory mounting brackets
and the 95-8202 DDIN trim plates to
the stacked ISO DIN head units with
the screws supplied with the units.
(Figure C) NOTE: Remove locating pins
from factory brackets with grinder.
Continue to final assembly.
19
Интернет-магазин автозвука и автотоваров Винавто
95-8202
FINAL ASSEMBLY
FINAL ASSEMBLY
1 Locate the factory wiring harness in the dash and make the connection as shown.
Metra recommends using the proper mating adapter and making the connections
as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit.)
2 Re-connect the negative battery terminal and test the unit for proper operation.
3 Reassemble radio and dash assemblies in reverse order of disassembly.
FINAL WIRING CONNECTIONS
to
.u
a
Make wiring connections using the EIA color code chart shown below and the instructions included with the head
unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually
tape off ends of any unused wires to prevent electrical short circuit.
C
D
A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
w
B
in
au
A
METRA / EIA WIRING CODE
12V Ignition / Acc . . . Red
12V Batt / Memory . . Yellow
Ground . . . . . . . . . . . Black*
Power Antenna . . . . . Blue
Amp Turn-On . . . . . . Blue / White
Amp Ground . . . . . . . Black / White
Illumination. . . . . . . . Orange
Dimmer . . . . . . . . . . Orange / White
Right Front (+) . . . . . Gray
Right Front (-). . . . . . Gray / Black
Left Front (+) . . . . . . White
Left Front (-) . . . . . . . White / Black
Right Rear (+). . . . . . Violet
Right Rear (-) . . . . . . Violet / Black
Left Rear (+). . . . . . . Green
Left Rear (-) . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
20
Интернет-магазин автозвука и автотоваров Винавто
95-8202
w
in
au
to
.u
a
NOTES
21
Интернет-магазин автозвука и автотоваров Винавто
w
in
au
to
.u
a
95-8202 INSTRUCTIONS
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
1-800-221-0932
REV. 06/23/11
www.metraonline.com
© COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION
INST95-8202