BHD20V8 Manual

BLUETOOTH INTERFACE FOR SELECT 2003-UP HONDA VEHICLES
BEEBH-28
BEEBH-02
BEEBH-03
BEEBH-04
BEEBH-05
APPLICATIONS
BEEBH-28
2008 - 2012
2006 - 2011
2007 - 2012
2009 - 2012
2008 - 2011
2009 - 2012
2009 - 2012
BEEBH-02
2003 - 2007
2005 - 2006
2003 - 2008
2005 - 2007
2003 - 2008
2006 - 2008
Accord DX/EX/LX
Civic/ Si
CRV
Fit
Odyssey
Pilot
Ridgeline
Accord DX/EX/LX
CRV
Element
Odyssey
Pilot
Ridgeline
BEEBH-03
2012 - UP CRV
2012 - UP Civic
We recommend reading this installation guide first before starting any
work. Following these instructions from “Start” to” Finish” will ensure
a smooth and hassle free installation. We offer telephone support M-F
9:00 AM – 5:00PM PDT at 1 (855) 822-1348. We are here to help.
24-PIN CONNECTORS:
TO FACTORY
HARNESS
PRELIMINARY:
- Disconnect the positive(+) battery cable for radios that are
non-navigation. Radios that are navigation ready should not
disconnect the battery cable. Please use caution when installing.
Do not install the interface near or on the vehicle’s HVAC system.
This will prevent overheating and condensation build up.
- Determine the proper installation method for your specific vehicle.
Use overview to help you determine installation method.
INSTALLATION
1. Remove the factory radio to gain access to the factory radio wiring
connectors.
2. Disconnect the factory connectors from the rear of the factory radio.
3. Connect the male connectors of the interface power harness into the
factory radio.
4. Reconnect the factory connectors into the mating connectors of the
interface harness.
5. Connect the male 3-pin connector into the pigtail connector.
6. Route the microphone to a desired location, (for example near the
rear view mirror).
7. Re-install a factory radio back into the vehicle’s dash.
24-PIN
TO FACTORY
RADIO
24-PIN
(female plug)
(male plug)
Note: When transferring a phone call to the mobile phone for privacy,
the user must re-connect the BEEBH-28 and the mobile phone by
selecting the module from the device menu on the phone.
Note: If after ending a call the radio is powered “OFF”, you must power
“ON” the radio to regain volume control.
12-PIN
(male plug)
24-PIN
(male plug)
3-PIN
(male plug)
USING THE STEERING WHEEL CONTROL BUTTONS
BALL JOINT
INITIAL PAIRING TO THE VOICE PROMPTS:
1. READY (POWER ON)
2. SEARCHING PHONES (FOR PREVIOUS PAIRED PHONES)
3. PLEASE SEARCH AND SELECT THE “BEEBH-28” DEVICE FROM
MOBILE PHONE AND ENTER “0000”.
4. YOU ARE NOW READY TO USE THE HF SYSTEM.
Note: The Bluetooth interface will remember up to the last 8 devices.
17 AND 20-PIN CONNECTORS:
PRESS AND HOLD CH DN FOR 2 SEC
ANSWER
PRESS CH UP BUTTON ONCE
END A CALL
PRESS CH DN BUTTON ONCE
REJECT
PRESS CH DN BUTTON ONCE
ANSWER SECOND CALL
PRESS CH UP BUTTON ONCE
SWITCH BETWEEN CALLS
PRESS CH UP BUTTON ONCE
INCREASE VOLUME
PRESS VOLUME UP ONCE
DECREASE VOLUME
PRESS VOLUME DN ONCE
PRIVACY MODE
PRESS CH UP ONCE
AUTO RE-CONNECT:
1. The BEEBH-28 module will automatically re-connect the a previously
paired mobile phone when the ignition is turned “ON” to the vehicle
and the mobile phone’s Bluetooth feature is also on.
MODE
Note: The Bluetooth module will re-connect with the last mobile phone’s
it was paired with. If no mobile phone is not found, it will
revert to the pairing process.
BEEBH-05 (Amplified Systems)
2003 - 2007 Accord DX/EX/LX
2005 - 2006 CRV
2003 - 2007 Element
2003 - 2007 Pilot
2005 - 2007 Odyssey (Non-Nav)
MIC
NO BLUETOOTH CONTROL FROM RADIO CONTROLS
BALL JOINT
SCAN
20-PIN BLUE CONNECTOR:
TO FACTORY
HARNESS
20-PIN
(female plug)
(male plug)
CD
12-PIN
(male plug)
24-PIN
(male plug)
A.SEL
TO FACTORY
RADIO
20-PIN
DSP
SOUND
1
2
RPT
RDM
SEEK
SKIP
3
4
5
DISC-
6
DISC+
TUNE
FOLDER
MIC
3-PIN
(male plug)
BALL JOINT
MOUNTING THE MICROPHONE
1. Insert the mounting clip into the ball joint on the microphone.
2. Mount the clip on your visor or near the rear view mirror.
3. Route the remaining cable along the edge of the roof liner and
towards the back of the radio, hiding the cable from sight.
+
VOL
ANSWER
CH
END
AM
FM
AUX
THIS KIT WILL ONLY SUPPORT
STEERING WHEEL CONTROL
EQUIPPED VEHICLES.
VOICE DIAL
Note: If pairing is unsuccessful after several attempts power off then
power back on to re-attempt, if unsuccessful please contact our tech
support line.
BEEBH-04 (Amplified Systems)
2008 - 2012 Accord
2008 - 2012 Pilot
2006 - 2011 Civic (Non-Nav)
IMPORTANT NOTE
Note: If an incoming call is answered from the mobile phone’s keypad,
the call will direct itself to the headset on the mobile phone. To re-direct
the phone call to the “BEEBH-28”, it must be done directly from the
mobile phone.
All features of this module may vary by mobile phone
manufacturer. For questions on your mobile phone’s
features, please reference the mobile phone’s user manual
for information.
Note: Premium Audio Systems need to “Turn On” the radio for handsfree audio to be heard.
BLUETOOTH INTERFACE FOR SELECT 2003-UP HONDA VEHICLES
BEEBH-28
BEEBH-02
BEEBH-03
BEEBH-04
BEEBH-05
APPLICATIONS
10-PIN
(male plug)
6-PIN
20-PIN
TO FACTORY
RADIO
Note: All menu structures work in 3 second increments.
If after 3 seconds the interface will time-out.
(male plug)
THIS KIT WILL ONLY SUPPORT
STEERING WHEEL CONTROL
EQUIPPED VEHICLES.
TALK BUTTON
6-PIN
IMPORTANT NOTE
Note: The menu structures only remember the last 24
numbers in the call log from dialed from the mobile
phone.
-
(male plug)
1. Press the “TALK” button twice.
2. Press the “TALK” button once, to enter the menu options.
Continue pressing the “TALK” button twice till you hear the
interface announce “DO YOU WANT TO DELETE PAIRED
PHONE LIST”.
3. Press the “SEEK UP” button once within 3 seconds to confirm.
4. The interface will ask “ARE YOU SURE”, press the “SEEK UP”
button once to re-confirm..
With the phone paired to the
UBT, enter the “SETTING TTS
LEXUS
VOLUME” under
PWR VOL
menu structure.
The default level is
at volume 4.
(male plug)
DELETE ALL PAIRED DEVICES:
This feature allows you to delete all paired devices on the interface.
The module does NOT allow the user to only clear one device. The
module will delete all previously paired devices only
Have you paired your mobile
device, and get no sound from
the radio? Try reseting the TTS
volume setting.
CH
TO FACTORY
HARNESS
BEEBH-05 (Amplified Systems)
2003 - 2007 Accord DX/EX/LX
2005 - 2006 CRV
2003 - 2007 Element
2003 - 2007 Pilot
2005 - 2007 Odyssey (Non-Nav)
SETTING TTS VOLUME:
1. Press the “TALK” button twice.
2. Press the “TALK” button once to enter the menu options.
Continue to press the “TALK” button twice till you hear the
interface announce “SETTING VOLUME”, and wait for her
announcement.
3. Set the TTS volume by pressing the volume Vol+ and Vol- waiting
for the announcement. Each announcement will indicate the volume
level of the TTS.
4. When the desired volume level is reached, press the “SEEK UP”
button once to select.
Remove the battery on the
mobile device for a minimum of
15 Seconds.
(male plug)
BEEBH-04 (Amplified Systems)
2008 - 2012 Accord
2008 - 2012 Pilot
2006 - 2011 Civic (Non-Nav)
PHONE MUST BE UNPAIRED
TO ENTER THE FOLLOWING
MENU STRUCTURE
Are you experiencing random
static interuptions durring your
phone calls?
24-PIN
BEEBH-03
2012 - UP CRV
2012 - UP Civic
VOL
Delete all paired devices on your
mobile device and on the UBT.
(See Using The Menu Structure)
(male plug)
Accord DX/EX/LX
CRV
Element
Odyssey
Pilot
Ridgeline
OUTGOING CALLS:
1. Press the “TALK” button once.
2. Press the “TALK” button once to enter the menu options.
Continue to press the “TALK” button till you hear the
interface announce “OUTGOING CALLS”, and wait for the
numbers to be announced.
3. When the number you wish to dial is announced, press the
“SEEK UP” button once to make the call.
+
Have a bad connection when
using the A2DP or Handsfree
profiles?
12-PIN
BEEBH-02
2003 - 2007
2005 - 2006
2003 - 2008
2005 - 2007
2003 - 2008
2006 - 2008
INCOMING CALLS:
1. Press the “TALK” button once.
2. Press the “TALK” button once to enter the menu options.
Continue to press the “TALK” button till you hear the
interface announce “INCOMING CALLS”, and wait for the
numbers to be announced.
3. When the number you wish to dial is announced, press the
“SEEK UP” button once to make the call.
MODE
3-PIN
Accord DX/EX/LX
Civic/ Si
CRV
Fit
Odyssey
Pilot
Ridgeline
MISSED CALLS:
1. Press and Hold the “CH DN” button.
2. Press the “TALK” button once to enter the menu options.
Continue to press the “TALK” button till you hear the
interface announce “MISSED CALLS”, and wait for the numbers
to be announced.
3. When the number you wish to dial is announced, press the
“SEEK UP” button once to make the call.
(male plug)
BEEBH-28
2008 - 2012
2006 - 2011
2007 - 2012
2009 - 2012
2008 - 2011
2009 - 2012
2009 - 2012
USING THE MENU STRUCTURE:
AM
SEEK TRAC