Round Bollard LED Light Problem Possible Causes

CPIN002084/4
TROUBLESHOOTING AND USER HINTS
Problem
Possible Causes
Possible Solutions
Lights do not operate.
No power.
Blown fuse.
Low voltage cable has not been connected to
transformer
Ensure transformer is plugged in and power is on.
(Is the power point working?)
Replace fuse. (Note: some transformers may not be
fitted with fuse).
Ensure the low voltage cable is connected to the
transformer. (Is the connection firm?)
Lights do not switch on at dusk when using either
the “Dusk Till Dawn” or “Timer” mode. (Daylight
Sensor/Timer transformers only, or when using
separate Time/Light Sensor, LVT).
Artificial light affecting Timer/Light Sensor (ie,
street lights, car lights, etc).
Timer/Light Sensor
Mount Timer/Light Sensor in a position where
artificial lights do not affect its operation. To check
light sensor: ensure switch is in either “Dusk Till
Dawn” or “Timer Hour” position, cover sensor lens
with black PVC tape (ensuring that no light gets
in). The lights should switch on after a few seconds.
If the lights have now switched on, the light sensor
may simply require mounting in a position where
artificial light cannot affect its operation.
Only some of the lights switch on.
Connecting pins in cable connector have not
penetrated into cable.
Globe not pressed into globe socket correctly.
Globe blown.
Straighten pins with pliers then reconnect.
Ensure globe is pushed firmly into position.
Replace globe.
Light stays on for longer period than the timer
suggests. Daylight Sensor/Timer transformers only,
or when using separate Time/Light Sensor, LVT
If the Timer/Light Sensor detects a light source
(porch light, car light etc) during the time in which
the garden lights are on, the transformer will switch
the garden lights off and then re-start the preprogrammed time again when the light has passed.
Mount Timer/Light Sensor in a position where
artificial light cannot affect its operation.
Warranty
Arlec guarantees this product in accordance with the Australian
Consumer Law.
Arlec also warrants to the original first purchaser of this product
(“you”) from a retailer that this product will be free of defects
in materials and workmanship for a period of 12 months from
the date of purchase; provided the product is not used other
than for the purpose, or in a manner not within the scope of
the recommendations and limitations, specified by Arlec, is
new and not damaged at the time of purchase, has not been
subjected to abuse, misuse, neglect or damage, has not been
modified or repaired without the approval of Arlec and has not
been used for commercial purposes (“Warranty”).
If you wish to claim on the Warranty, you must, at your own
expense, return the product, and provide proof of original
purchase and your name, address and telephone number, to
Arlec at the address below or the retailer from whom you
originally purchased the product within 12 months from the
date of purchase.
Arlec will (or authorise the retailer to) assess any claim you may
make on the Warranty in the above manner and if, in Arlec’s
reasonable opinion, the Warranty applies, Arlec will at its
own option and expense (or authorise the retailer to) replace
the product with the same or similar product or repair the
product and return it to you or refund the price you paid for
the product. Arlec will bear its own expenses of doing those
things, and you must bear any other expenses of claiming on
the Warranty.
The Warranty is in addition to other rights and remedies you
may have under a law in relation to the product to which the
Warranty relates.
Our goods come with guarantees that cannot be excluded
under the Australian Consumer Law. You are entitled to a
Round Bollard
LED Light
LVG511
Installation Instructions
replacement or refund for a major failure and for compensation
for any other reasonably foreseeable loss or damage. You are
also entitled to have the goods repaired or replaced if the goods
fail to be of acceptable quality and the failure does not amount
to a major failure.
Proof of Purchase
Please retain your proof of purchase for all warranty claims.
For all Sales & Warranty enquiries
Arlec Australia Pty. Ltd. ACN 009 322 105
(“Arlec”) gives the Warranty.
Building 3, 31 – 41 Joseph Street,
Blackburn North, Victoria, 3130
P.O. Box 1065,
Blackburn North, 3130
Customer Service: (03) 9982 5111
Email: custservice@arlec.com.au
© This instruction leaflet is subject to copyright and
must not be reproduced, copied or otherwise used
in any way or for any purpose without the consent in
writing of the owner,
Arlec Australia Pty Ltd (A.C.N. 009 322 105).
CPIN002084/4
Keep these instructions in a safe place for future reference
Insulating Strip
CONNECTING GARDEN LIGHT TO
LOW VOLTAGE CABLE
IMPORTANT: Low voltage cable is
NOT to be used for 240 volt wiring.
6. Fit the cable from the light into the
narrower slot of the connector,
keeping the cable straight, push it
down onto the two spiked pins (Fig.2).
7. Fit the connector to the main garden
lighting cable at the chosen position
by placing the garden lighting cable in
the larger slot of the cable connector.
Push it down on to the two spiked
pins (Fig.3).
8. Refit the cover of the cable connector
and tighten all three screws.
9. The garden light should now illuminate.
If the light does not illuminate, see
section headed “Trouble Shooting and
User Hints”
Each of the LVG511 presents a 1.5 watt
load on the transformer.
Precaution should be taken so as to make
sure that the sums of the light wattages
of your garden lights not exceed the
wattage or VA) rating of the transformer.
For example, a 24 watt transformer
running three 4 watt bulbs could also
accept up to eight of theses LVG 511
lights.
ie ( 3x4watt) + (8x1.5 watt) = 24 watts
NOTE: Cable lengths greater than 18
metres may cause a small reduction in
brightness to the lights furthest away
from the transformer.
1. If you are adding lights to your existing
garden lighting plan, first check that
the transformer is powerful enough to
illuminate lights.
(See chart on page 4, Maximum load
Capacity of Arlec Garden Lighting
Transformers)
2. Additional cable can be joined to
existing cable either at the end of the
length, or joined anywhere along the
cable using an Arlec Cable Connector
LV700. Arlec low voltage cable is
completely weatherproof and may be
used above or below ground.
3. Lay low voltage cable out in position in
readiness for connecting lights.
4. Plug the transformer into a household
powerpoint and switch “ON”.
This will enable you to check light
connections during installation.
This operation is completely safe
because the wiring is only carrying a
low 12volt.
5. Open the cable connector provided
by unscrewing the top cover of the
connector.
Do not remove the insulating strip
from the middle slot (Fig.1).
2
Fig 1
NOTES ON DESIGN OF YOUR
GARDEN LIGHTING SYSTEM
1. Ensure that the wattage of the
transformer is greater than the total
wattage of lights.
For example, a 42 watt transformer is
capable of supplying max 42 watts of
lightning. If sixteen LVG511 lamps are
to be installed (16 x 1.5= 24 Watts),
18Watts of lighting remains, which
would accommodate three garden
lights of 6 watts each, but only four,
4 watt lights could be connected.
2. If possible avoid cable runs of more
than 18 metres, as reduced brightness
may occur, and definitely no more
than 32 metres. In larger systems, or
where the total wattage is over 50
watts, split the lighting into two cable
runs, where each cable comes back to
be fed by the transformer.
This will ensure better power
distribution and globe brightness.
Fig 2
Fig 3
MAXIMUM LOAD OF ARLEC GARDEN LIGHTING TRANSFORMERS
Arlec Transformer
Model No.
Number of lamps which Maximum Length of
can be connected.
cable
LV24 (24 watt)
16
32 metres
LV42 or LV42-T (42 watt)
28
32 metres
62001 (75 watt)
50
2 runs x 32 meters
LV90 (90 watt)
60
2 runs x 32 meters
LV250 (250 watt)
166
4 runs x 32 meters
3