5-Port 10/100Mbps GREENnet Switch (TE100-S50g) 8-Port 10/100Mbps GREENnet Switch (TE100-S80g) ŸQuick Installation Guide (1) ŸTechnical Specifications  ŸTroubleshooting (15) 1.03 1. Before You Start Package Contents ŸTE100-S50g/TE100-S80g ŸMulti-Language Quick Installation Guide ŸPower Adapter (7.5V DC, 1A) If any of the above contents are missing, please contact your reseller. Minimum Requirements ŸA computer with a network adapter installed ŸCAT-5, CAT-5e or CAT-6 Network Cable ŸThe surface must support at least 265g for the Switch. ŸThe power outlet should be within 1.8 meters (6 feet) of the Switch. ŸVisually inspect the DC power jack to make sure that it is securely connected to the power adapter ŸMake sure that there is proper heat dissipation from and adequate ventilation around the switch ŸDo not place heavy objects on the switch 2. Hardware Installation 1. Connect the Power Adapter to the TE100-S50g/TE100-S80g and then to a power outlet. 2. Connect a CAT-5, CAT-5e or CAT-6 RJ-45 network cable from the computer to an available Ethernet port on the TE100-S50g/ TE100-S80g. 1 3. LEDs Power ŸGreen: Power is on ŸNot Illuminated: Power is off Link/ACT ŸGreen(Solid): Link to another device. ŸGreen(Blinking): Activity is occurring from the link. ŸNot Illuminated: Nothing is detected on the port. 100Mbps ŸGreen: Connection for the port is 100/200Mbps (Half/Full) ŸNot Illuminated: Connection for the port is 10/20 (Half/Full) or nothing is detected on the port. Your configuration is complete For detailed information regarding the TE100-S50g/TE100-S80g’s configuration and advanced settings, please refer to the Troubleshooting section, or TRENDnet's website at http://www.trendnet.com. 2 Technical Specifications Hardware Standards Network Media Data Transfer Rates Protocol/Topology ŸIEEE 802.3 10BASE-T ŸIEEE 802.3u 100BASE-TX ŸIEEE 802.3x Flow Control ŸEthernet: 2-Pair UTP/STP CAT-3, -4, -5 ŸFast Ethernet: 2-Pair UTP/STP CAT-5, -5e , -6 ŸEthernet: 10Mbps (half-duplex), 20Mbps (full-duplex) ŸFast Ethernet: 100Mbps (half-duplex), 200Mbps (full-duplex) CSMA/CD / Star Interface ŸTE100-S50g: 5 x 10/100/1000 Auto-MDIX RJ-45 ports ŸTE100-S80g: 8 x 10/100/1000 Auto-MDIX RJ-45 ports Data RAM Buffer ŸTE100-S50g: 384Kbytes per device ŸTE100-S80g: 768Kbytes per device Packet Filtering/ Forwarding Rate Ÿ10Mbps Ethernet: 14,880pps (packet per second) Ÿ100Mbps Fast Ethernet: 148,800pps MAC Address Learning Automatic Update Filtering Table 1K entries per device Switch Fabric ŸTE100-S50g: 1Gbps Forwarding Capacity ŸTE100-S80g: 1.6Gbps Forwarding Capacity Power Consumption Diagnostic LEDs ŸTE100-S50g: 2.1W (max) ŸTE100-S80g: 2.5W (max) Power, Link/ACT, 100Mbps Power Adapter 7.5V DC, 1A External Power Adapter Dimensions ŸTE100-S50g: 116 x 25 x 70 mm (4.57 x .98 x 2.76 in.) ŸTE100-S80g: 136 x 25 x 70 mm (5.35 x .98 x 2.76 in.) Weight ŸTE100-S50g: 225g ŸTE100-S80g: 265g Temperature ŸOperating: 0° ~ 40° C (32° ~ 104° F) ŸStorage: -10° ~ 70° C (14° ~ 158° F) Humidity ŸOperating: 10% ~ 90% ŸStorage: 5% ~ 90% CE, FCC Certification 3 Troubleshooting 1. After connecting the switch to a power outlet, the LEDs do not turn on. 1. Check the connection of the external power adapter to the TE100-S50g/TE100-S80g and the power outlet. 2. Check that the power outlet is receiving power. 2. When I connect a computer to the switch's port, the LINK/ACT LED turns on, but the 100Mbps LED remains off. When the 100Mbps LED is off, the computer's connection speed is 10Mbps. 3. After I connect my PCs to the switch, I am unable to share files. 1. Check the LEDs on the switch. Make sure the LINK/ACT LED is on. 2. Check the network cable. The minimum length of the cable is 1.5 meters and the maximum length of the cable is 100 meters. 3. Disable any software firewall program. 4. Verify that you have file sharing enabled. Please contact your Operating System support for more information. 4. After I connect my PCs to the switch, I can only get onto the Internet from one computer. The switch was not designed to share Internet between multiple computers. You need to get an Internet router such as the TW100-S4W1CA. 5. Where is the uplink port located on the switch? Since all the ports on the switch are Auto-MDIX, any of the ports can be used as an uplink port. If you still encounter problems or have any questions regarding the TE100-S50g/TE100-S80g please contact TRENDnet's Technical Support Department. 4 Limited Warranty TRENDnet warrants its products against defects in material and workmanship, under normal use and service, for the following lengths of time from the date of purchase. TE100-S50g/TE100-S80g - 3 Year Limited Warranty AC/DC Power Adapter, Cooling Fan and Power Supply carry 1 year warranty If a product does not operate as warranted during the applicable warranty period, TRENDnet shall reserve the right, at its expense, to repair or replace the defective product or part and deliver an equivalent product or part to the customer. The repair/replacement unit's warranty continues from the original date of purchase. All products that are replaced become the property of TRENDnet. Replacement products may be new or reconditioned. TRENDnet does not issue refunds or credit. Please contact the point-of-purchase for their return policies. TRENDnet shall not be responsible for any software, firmware, information, or memory data of customer contained in, stored on, or integrated with any products returned to TRENDnet pursuant to any warranty. There are no user serviceable parts inside the product. Do not remove or attempt to service the product by any unauthorized service center. This warranty is voided if (i) the product has been modified or repaired by any unauthorized service center, (ii) the product was subject to accident, abuse, or improper use (iii) the product was subject to conditions more severe than those specified in the manual. Warranty service may be obtained by contacting TRENDnet within the applicable warranty period and providing a copy of the dated proof of the purchase. Upon proper submission of required documentation a Return Material Authorization (RMA) number will be issued. An RMA number is required in order to initiate warranty service support for all TRENDnet products. Products that are sent to TRENDnet for RMA service must have the RMA number marked on the outside of return packages and sent to TRENDnet prepaid, insured and packaged appropriately for safe shipment. Customers shipping from outside of the USA and Canada are responsible for return shipping fees. Customers shipping from outside of the USA are responsible for custom charges, including but not limited to, duty, tax, and other fees. WARRANTIES EXCLUSIVE: IF THE TRENDNET PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, THE CUSTOMER'S SOLE REMEDY SHALL BE, AT TRENDNET'S OPTION, REPAIR OR REPLACE. THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. TRENDNET NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION MAINTENANCE OR USE OF TRENDNET'S PRODUCTS. TRENDNET SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY CUSTOMER'S OR ANY THIRD PERSON'S MISUSE, NEGLECT, IMPROPER INSTALLATION OR TESTING, UNAUTHORIZED ATTEMPTS TO REPAIR OR MODIFY, OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING, OR OTHER HAZARD. LIMITATION OF LIABILITY: TO THE FULL EXTENT ALLOWED BY LAW TRENDNET ALSO EXCLUDES FOR ITSELF AND ITS SUPPLIERS ANY LIABILITY, WHETHER BASED IN CONTRACT OR TORT (INCLUDING NEGLIGENCE), FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND, OR FOR LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF INFORMATION OR DATE, OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE, OR INTERRUPTION OF THE POSSIBILITY OF SUCH DAMAGES, AND LIMITS ITS LIABILITY TO REPAIR, REPLACEMENT, OR REFUND OF THE PURCHASE PRICE PAID, AT TRENDNET'S OPTION. THIS DISCLAIMER OF LIABILITY FOR DAMAGES WILL NOT BE AFFECTED IF ANY REMEDY PROVIDED HEREIN SHALL FAIL OF ITS ESSENTIAL PURPOSE. Governing Law: This Limited Warranty shall be governed by the laws of the state of California. Some TRENDnet products include software code written by third party developers. These codes are subject to the GNU General Public License ("GPL") or GNU Lesser General Public License ("LGPL"). Go to http://www.trendnet.com/gpl or http://www.trendnet.com Download section and look for the desired TRENDnet product to access to the GPL Code or LGPL Code. These codes are distributed WITHOUT WARRANTY and are subject to the copyrights of the developers. TRENDnet does not provide technical support for these codes. Please go to http://www.gnu.org/licenses/gpl.txt or http://www.gnu.org/licenses/lgpl.txt for specific terms of each license. PWP05202009v2 TRENDnet 20675 Manhattan Place Torrance, CA 90501. USA Copyright ©2011. All Rights Reserved. TRENDnet.