Allied Telesis MCF2012LC/1 Multi-channel Modular Media Converters manual

Management
Software
AT-S85 and AT-S97
◆
Command Line
User’s Guide
AT-S85 Version 3.0.0 Management Software and AT-MCF2012LC, AT-MCF2012LC/1 and
AT-MCF2032SP Media Converter Modules
AT-S97 Version 3.0.0 Management Software and AT-MCF2000M Management Module
613-000789 Rev. D
Copyright © 2009 Allied Telesis, Inc.
All rights reserved. No part of this publication may be reproduced without prior written permission from Allied Telesis, Inc.
Allied Telesis and the Allied Telesis logo are trademarks of Allied Telesis, Incorporated. All other product names, company names, logos or
other designations mentioned herein are trademarks or registered trademarks of their respective owners.
Allied Telesis, Inc. reserves the right to make changes in specifications and other information contained in this document without prior
written notice. The information provided herein is subject to change without notice. In no event shall Allied Telesis, Inc.be liable for any
incidental, special, indirect, or consequential damages whatsoever, including but not limited to lost profits, arising out of or related to this
manual or the information contained herein, even if Allied Telesis, Inc. has been advised of, known, or should have known, the possibility of
such damages.
Contents
Preface ............................................................................................................................................................ 11
Document Conventions .................................................................................................................................... 12
Where to Find Web-based Guides ................................................................................................................... 13
Contacting Allied Telesis .................................................................................................................................. 14
Online Support ........................................................................................................................................... 14
Email and Telephone Support.................................................................................................................... 14
Returning Products .................................................................................................................................... 14
Sales or Corporate Information .................................................................................................................. 14
Management Software Updates................................................................................................................. 14
Chapter 1: Starting a Management Session ............................................................................................... 15
Management Overview..................................................................................................................................... 16
AT-S85 and AT-S97 Management Software.............................................................................................. 16
Features of the AT-S97 Management Software......................................................................................... 16
AT-S97 Command Line Interface............................................................................................................... 17
Manager Privilege Levels........................................................................................................................... 17
Starting a Local Management Session............................................................................................................. 18
Starting a Remote Telnet or Secure Shell Management Session .................................................................... 20
SNMP Management Session ........................................................................................................................... 22
Saving Your Configuration Changes ................................................................................................................ 23
Quitting a Management Session ...................................................................................................................... 24
Chassis ID Numbers......................................................................................................................................... 25
Slot Numbers and Letters................................................................................................................................. 26
Command Line Interface Features ................................................................................................................... 28
Command Formatting....................................................................................................................................... 29
What to Configure First..................................................................................................................................... 30
Displaying the Chassis Modules ................................................................................................................ 30
Changing the Manager Password.............................................................................................................. 32
Creating a Master Configuration File ......................................................................................................... 32
Assigning an IP Address Configuration...................................................................................................... 33
Setting the Date and Time ......................................................................................................................... 34
Enabling the Telnet or Secure Shell Server ............................................................................................... 35
Naming a Chassis ...................................................................................................................................... 35
Saving Your Changes ................................................................................................................................ 36
Replacing a Media Converter Module .............................................................................................................. 37
Chapter 2: Basic Commands ........................................................................................................................ 39
‘?’ Question Mark Key ...................................................................................................................................... 40
CLEAR.............................................................................................................................................................. 41
EXIT.................................................................................................................................................................. 42
HELP ................................................................................................................................................................ 43
PING................................................................................................................................................................. 44
3
Contents
Chapter 3: IP Configuration Commands ...................................................................................................... 47
Overview ........................................................................................................................................................... 48
Command Summary................................................................................................................................... 49
IP DHCP DISABLE ........................................................................................................................................... 50
IP DHCP ENABLE ............................................................................................................................................ 51
IP SET............................................................................................................................................................... 52
IP SHOW .......................................................................................................................................................... 54
Chapter 4: General System Commands ....................................................................................................... 55
Overview ........................................................................................................................................................... 56
Command Summary................................................................................................................................... 56
SYSTEM SET ASYNCHRONOUS.................................................................................................................... 58
SYSTEM SET CHASSIS .................................................................................................................................. 59
SYSTEM SET CLOCK ...................................................................................................................................... 60
SYSTEM SET CONSOLE................................................................................................................................. 62
SYSTEM SET CONTACT ................................................................................................................................. 63
SYSTEM SET HOSTNAME .............................................................................................................................. 64
SYSTEM SET LOCATION ................................................................................................................................ 65
SYSTEM SHOW ASYNCHRONOUS ............................................................................................................... 66
SYSTEM SHOW CLOCK.................................................................................................................................. 67
SYSTEM SHOW CONSOLE ............................................................................................................................ 68
SYSTEM SHOW INFO ..................................................................................................................................... 69
Chapter 5: Port and Module Commands ...................................................................................................... 71
Overview ........................................................................................................................................................... 72
Command Summary................................................................................................................................... 72
SYSTEM RESET CHASSIS ............................................................................................................................. 74
SYSTEM RESET CLUSTER ............................................................................................................................ 76
SYSTEM RESET MODULE .............................................................................................................................. 78
SYSTEM SET INTERFACE .............................................................................................................................. 81
SYSTEM SET INTERFACE PORTNAME......................................................................................................... 87
SYSTEM SET MODULE ................................................................................................................................... 89
SYSTEM SET PORT ........................................................................................................................................ 92
SYSTEM SHOW CHASSIS .............................................................................................................................. 99
SYSTEM SHOW CLUSTER ...........................................................................................................................101
SYSTEM SHOW INTERFACE........................................................................................................................103
SYSTEM SHOW MODULE.............................................................................................................................111
Chapter 6: Network Time Protocol Commands .........................................................................................117
Overview .........................................................................................................................................................118
NTP Client Guidelines ..............................................................................................................................118
Command Summary.................................................................................................................................118
NTP DISABLE.................................................................................................................................................120
NTP ENABLE..................................................................................................................................................121
NTP SET .........................................................................................................................................................122
NTP SHOW.....................................................................................................................................................123
Chapter 7: Event Log and Syslog Client Commands ...............................................................................125
Overview .........................................................................................................................................................126
Syslog Client Guidelines...........................................................................................................................126
Command Summary.................................................................................................................................127
LOGGING CLEAR EVENTLOG......................................................................................................................128
LOGGING DISABLE EVENTLOG ..................................................................................................................129
LOGGING DISABLE SYSLOG .......................................................................................................................130
LOGGING ENABLE EVENTLOG ...................................................................................................................131
LOGGING ENABLE SYSLOG ........................................................................................................................132
LOGGING SET EVENTLOG...........................................................................................................................133
4
AT-S85 and AT-97 Management Software User’s Guide
LOGGING SET SYSLOG ............................................................................................................................... 135
LOGGING SHOW........................................................................................................................................... 136
LOGGING SHOW EVENTLOG ...................................................................................................................... 138
Chapter 8: Configuration File Commands ................................................................................................ 145
Overview......................................................................................................................................................... 146
Management Module and the Master Configuration File ......................................................................... 146
Media
Converter Modules and Auxiliary Configuration Files..................................................................................... 146
Saving Your Parameter Changes ............................................................................................................ 147
Creating a New Master Configuration File ............................................................................................... 148
Specifying the Active Master Configuration File....................................................................................... 149
Editing a Master Configuration File .......................................................................................................... 150
Command Summary ................................................................................................................................ 157
CONFIG OVERWRITE................................................................................................................................... 158
CONFIG RUN................................................................................................................................................. 160
CONFIG SAVE ............................................................................................................................................... 161
CONFIG SAVE FILESYSTEM........................................................................................................................ 162
CONFIG SET.................................................................................................................................................. 164
CONFIG SHOW ............................................................................................................................................. 166
Chapter 9: File System Commands ........................................................................................................... 169
Overview......................................................................................................................................................... 170
Managing a Module’s File System ........................................................................................................... 170
Updating the AT-S85 and AT-S97 Management Software ...................................................................... 170
Uploading or Downloading a Master Configuration File........................................................................... 171
Guidelines to Using the TFTP Client........................................................................................................ 171
Command Summary ................................................................................................................................ 172
FILE COPY..................................................................................................................................................... 173
FILE DELETE ................................................................................................................................................. 176
FILE DOWNLOAD.......................................................................................................................................... 179
FILE FASTDOWNLOAD................................................................................................................................. 186
FILE RENAME................................................................................................................................................ 188
FILE SHOW.................................................................................................................................................... 191
FILE UPLOAD ................................................................................................................................................ 194
Chapter 10: Telnet Server Commands ...................................................................................................... 197
Overview......................................................................................................................................................... 198
Telnet Server Guidelines.......................................................................................................................... 198
Command Summary ................................................................................................................................ 198
TELNET DISABLE.......................................................................................................................................... 200
TELNET ENABLE........................................................................................................................................... 201
TELNET SHOW.............................................................................................................................................. 202
Chapter 11: Simple Network Management Protocol (SNMP) Commands .............................................. 203
Overview......................................................................................................................................................... 204
SNMP Guidelines..................................................................................................................................... 204
Trap Events.............................................................................................................................................. 204
Command Summary ................................................................................................................................ 205
SNMP SET ..................................................................................................................................................... 206
SNMP SHOW ................................................................................................................................................. 208
5
Contents
Chapter 12: Secure Shell Server (SSH) Commands .................................................................................209
Overview .........................................................................................................................................................210
SSH Server Guidelines.............................................................................................................................210
Command Summary.................................................................................................................................211
SSH DISABLE ................................................................................................................................................212
SSH ENABLE .................................................................................................................................................213
SSH SHOW ....................................................................................................................................................214
Chapter 13: Manager Account Commands ................................................................................................215
Overview .........................................................................................................................................................216
Manager Account Guidelines ...................................................................................................................216
Command Summary.................................................................................................................................216
USER ADD .....................................................................................................................................................218
USER DELETE ...............................................................................................................................................220
USER SET ......................................................................................................................................................221
USER SHOW ..................................................................................................................................................223
Chapter 14: Diagnostics Commands .........................................................................................................225
Overview .........................................................................................................................................................226
Command Summary.................................................................................................................................226
DIAGNOSTICS SHOW BOOTLOADER .........................................................................................................227
DIAGNOSTICS SHOW CHASSIS ..................................................................................................................230
DIAGNOSTICS SHOW MODULE...................................................................................................................232
DIAGNOSTICS SHOW SOFTWARE..............................................................................................................235
Appendix A: AT-S85 and AT-S97 Management Software Default Settings ............................................239
AT-S85 Management Software.......................................................................................................................240
AT-S97 Management Software.......................................................................................................................241
Index ..............................................................................................................................................................243
6
Figures
Figure 1: Connecting the RS-232 Serial Management Cable to the RS-232 Terminal Port.................................................18
Figure 2: Command Line Interface Prompt...........................................................................................................................19
Figure 3: Slot Numbers and Letters for the AT-MCF2000 Chassis ......................................................................................26
Figure 4: Slot Numbers and Letters for the AT-MCF2300 Chassis ......................................................................................27
Figure 5: Displaying the Chassis Modules............................................................................................................................30
Figure 6: Displaying the Chassis Modules of a Stack...........................................................................................................31
Figure 7: Determining the Configuration Overwrite Setting of a Media Converter Module...................................................37
Figure 8: IP SHOW Command .............................................................................................................................................54
Figure 9: SYSTEM SHOW ASYNCHRONOUS Command ..................................................................................................66
Figure 10: SYSTEM SHOW CLOCK Command...................................................................................................................67
Figure 11: SYSTEM SHOW INFO Command ......................................................................................................................69
Figure 12: SYSTEM SHOW CHASSIS Command ...............................................................................................................99
Figure 13: SYSTEM SHOW CLUSTER Command ............................................................................................................102
Figure 14: SYSTEM SHOW INTERFACE Command - Chassis ID Only............................................................................104
Figure 15: Chassis ID and Slot Number .............................................................................................................................105
Figure 16: SYSTEM SHOW INTERFACE Command - Chassis ID, Slot Number and Channel Number...........................108
Figure 17: SYSTEM SHOW MODULE Command for a Power Supply or Fan Module ......................................................112
Figure 18: SYSTEM SHOW MODULE Command for the Management Module................................................................113
Figure 19: SYSTEM SHOW MODULE Command for a Media Converter Module .............................................................113
Figure 20: NTP SHOW Command......................................................................................................................................123
Figure 21: LOGGING SHOW Command ............................................................................................................................136
Figure 22: LOGGING SHOW EVENT-LOG Command ......................................................................................................138
Figure 23: Chassis and Slot IDs .........................................................................................................................................140
Figure 24: Management Module Configuration Header......................................................................................................150
Figure 25: System Configuration Section ...........................................................................................................................150
Figure 26: IP Configuration Section....................................................................................................................................151
Figure 27: Log Configuration Section .................................................................................................................................152
Figure 28: NTP Configuration Section ................................................................................................................................152
Figure 29: Telnet and SSH Configuration Section..............................................................................................................153
Figure 30: User Configuration Section................................................................................................................................153
Figure 31: SNMP Configuration Section.............................................................................................................................154
Figure 32: Blade Configuration Header ..............................................................................................................................154
Figure 33: Blade Configuration - Operating Mode Section .................................................................................................155
Figure 34: Blade Configuration - Port Operating Parameters.............................................................................................156
Figure 35: Blade Configuration - Module Name and Temperature Threshold Section.......................................................156
Figure 36: CONFIG SHOW Command...............................................................................................................................166
Figure 37: CONFIG SHOW Command with a New Active Master File...............................................................................167
Figure 38: CONFIG SHOW Command with a New Current and Active Master File...........................................................167
Figure 39: FILE SHOW Command .....................................................................................................................................192
Figure 40: TELNET SHOW Command ...............................................................................................................................202
Figure 41: SNMP SHOW Command ..................................................................................................................................208
Figure 42: SSH SHOW Command .....................................................................................................................................214
Figure 43: USER SHOW Command...................................................................................................................................223
Figure 44: DIAGNOSTICS SHOW BOOTLOADER Command ..........................................................................................228
Figure 45: DIAGNOSTICS SHOW CHASSIS EEPROM Command...................................................................................230
Figure 46: DIAGNOSTICS SHOW MODULE Command....................................................................................................233
Figure 47: DIAGNOSTICS SHOW BOOTLOADER Command ..........................................................................................236
7
Figures
8
Tables
Table 1: AT-MCF2000 Chassis Slots ..................................................................................................................................26
Table 2: AT-MCF2300 Chassis Slots ..................................................................................................................................27
Table 3: IP Configuration Commands ..................................................................................................................................49
Table 4: General System Configuration Commands ...........................................................................................................56
Table 5: Port and Module Commands .................................................................................................................................72
Table 6: SYSTEM SHOW CHASSIS Command ...............................................................................................................100
Table 7: SYSTEM SHOW INTERFACE Command - Chassis ID Only ..............................................................................105
Table 8: SYSTEM SHOW INTERFACE Command - Chassis ID and Slot Number ..........................................................106
Table 9: Port Status in the Link Test Mode ........................................................................................................................106
Table 10: Port Status in the Missing Link Mode ................................................................................................................107
Table 11: Port Status in the Smart Missing Link Mode ......................................................................................................107
Table 12: SYSTEM SHOW INTERFACE Command - Chassis ID, Slot Number and Channel Number ...........................108
Table 13: SYSTEM SHOW MODULE Command ..............................................................................................................114
Table 14: NTP Client Commands ......................................................................................................................................118
Table 15: Event Log and Syslog Client Commands ..........................................................................................................127
Table 16: Severity Level Definitions ..................................................................................................................................139
Table 17: Slot Identifiers ....................................................................................................................................................140
Table 18: Event Messages ................................................................................................................................................140
Table 19: Configuration File Commands ...........................................................................................................................157
Table 20: File System Commands .....................................................................................................................................172
Table 21: Telnet Server Commands ..................................................................................................................................198
Table 22: SNMP Commands .............................................................................................................................................205
Table 23: Secure Shell Server Commands .......................................................................................................................211
Table 24: Manager Account Commands ...........................................................................................................................216
Table 25: Diagnostics Commands .....................................................................................................................................226
Table 26: DIAGNOSTICS SHOW BOOTLOADER Command ..........................................................................................228
Table 27: DIAGNOSTICS SHOW CHASSIS EEPROM Command ...................................................................................231
Table 28: DIAGNOSTICS SHOW CHASSIS EEPROM Command ...................................................................................233
Table 29: DIAGNOSTICS SHOW BOOTLOADER Command ..........................................................................................236
Table 30: Default Settings for the AT-S85 Management Software ....................................................................................240
Table 31: Default Settings for the AT-S97 Management Software ....................................................................................241
9
Tables
10
Preface
The AT-S85 and AT-S97 Management Software programs are the
operating systems for the AT-MCF2000 Media Converter Modules and the
AT-MCF2000M Management Module, respectively. This guide explains
how to use the management programs to control and monitor the
operating parameters of the media converter modules in the AT-MCF2000
Series.
This preface contains the following sections:
ˆ
“Document Conventions” on page 12
ˆ
“Where to Find Web-based Guides” on page 13
ˆ
“Contacting Allied Telesis” on page 14
Caution
The software described in this documentation contains certain
cryptographic functionality and its export is restricted by U.S. law. As
of this writing, it has been submitted for review as a “retail encryption
item” in accordance with the Export Administration Regulations, 15
C.F.R. Part 730-772, promulgated by the U.S. Department of
Commerce, and conditionally may be exported in accordance with
the pertinent terms of License Exception ENC (described in 15
C.F.R. Part 740.17). In no case may it be exported to Cuba, Iran,
Iraq, Libya, North Korea, Sudan, or Syria. If you wish to transfer this
software outside the United States or Canada, please contact your
local Allied Telesis sales representative for current information on
this product’s export status.
11
Preface
Document Conventions
This document uses the following conventions:
Note
Notes provide additional information.
Caution
Cautions inform you that performing or omitting a specific action
may result in equipment damage or loss of data.
Warning
Warnings inform you that performing or omitting a specific action
may result in bodily injury.
12
AT-S85 and AT-S97 Management Software User’s Guide
Where to Find Web-based Guides
The installation and user guides for the Allied Telesis products are
available in portable document format (PDF) on our web site at
www.alliedtelesis.com. You can view the documents online or download
them onto a local workstation or server.
For details about the features and functions of the AT-MCF2000 Media
Converter, refer to the AT-MCF2000 Multi-channel Media Converter
Series Installation Guide (part number 613-001096) on our web site:
13
Preface
Contacting Allied Telesis
This section provides Allied Telesis contact information for technical
support as well as sales and corporate information.
Online Support
You can request technical support online by accessing the Allied Telesis
Knowledge Base: www.alliedtelesis.com/support/kb.aspx. You can use
the Knowledge Base to submit questions to our technical support staff and
review answers to previously asked questions.
Email and
Telephone
Support
For Technical Support via email or telephone, refer to the Support section
of the Allied Telesis web site: www.alliedtelesis.com.
Returning
Products
Products for return or repair must first be assigned a return materials
authorization (RMA) number. A product sent to Allied Telesis without an
RMA number will be returned to the sender at the sender’s expense. For
instructions on how to obtain an RMA number, go to the Support section
on our web site at www.alliedtelesis.com.
Sales or
Corporate
Information
You can contact Allied Telesis for sales or corporate information through
our web site at www.alliedtelesis.com.
Management
Software Updates
New releases of the management software for our managed products are
available from the following Internet sites:
ˆ
Allied Telesis web site: www.alliedtelesis.com
ˆ
Allied Telesis FTP server: ftp://ftp.alliedtelesis.com
If the FTP server prompts you to log on, enter “anonymous” as the user
name and your email address as the password.
14
Chapter 1
Starting a Management Session
This chapter contains the following sections:
ˆ
“Management Overview” on page 16
ˆ
“Starting a Local Management Session” on page 18
ˆ
“Starting a Remote Telnet or Secure Shell Management Session” on
page 20
ˆ
“SNMP Management Session” on page 22
ˆ
“Saving Your Configuration Changes” on page 23
ˆ
“Quitting a Management Session” on page 24
ˆ
“Chassis ID Numbers” on page 25
ˆ
“Slot Numbers and Letters” on page 26
ˆ
“Command Line Interface Features” on page 28
ˆ
“Command Formatting” on page 29
ˆ
“What to Configure First” on page 30
ˆ
“Replacing a Media Converter Module” on page 37
15
Chapter 1: Starting a Management Session
Management Overview
The discussions in this section review the basic characteristics of the
management software for the AT-MCF2000 Media Converter Series.
AT-S85 and
AT-S97
Management
Software
The modules in the AT-MCF2000 Series use two different operating
systems. The AT-MCF2000M Management Module uses the AT-S97
Management Software and the AT-MCF2012LC, AT-MCF2012LC/1 and
AT-MCF2032SP Media Converter Modules use the AT-S85 Management
Software.
All of your commands must be entered through the AT-S97 Management
Software on the management module. Commands intended for a media
converter module are automatically transferred by the management
module to the appropriate module in the chassis or stack.
Features of the
AT-S97
Management
Software
Here are the functions that you can perform using the AT-MCF2000M
Management Module and Version 3.0.0 of the AT-S97 Management
Software:
ˆ
Set the operating parameters on the twisted pair and fiber optic ports
of the media converter channels, including:
– Auto-Negotiation
– Speed
– Duplex mode
– MDI/MDI-X configuration
ˆ
Change a channel’s operating mode. The operating modes are listed
here:
– MissingLink™
– Smart MissingLink
– Link Test
16
ˆ
Implement rate limits on the ingress and egress packets on the ports of
the media converter channels.
ˆ
Configure the module’s Network Time Protocol (NTP) client to set the
system’s date and time from a NTP server on your network or the
Internet.
ˆ
Create a stack of enclosures of up to sixteen media converter modules
so that you can manage the modules from one management module.
ˆ
Manage the modules locally using the RS-232 Terminal Port or
remotely using a Telnet or SSH client.
ˆ
Manage the modules remotely using Simple Network Management
Protocol (SNMP).
AT-S85 and AT-S97 Management Software User’s Guide
AT-S97
Command Line
Interface
ˆ
Monitor the operations of the modules from an event log.
ˆ
Send the event messages to a Syslog server on your network.
The AT-S97 Management Software has a command line interface which
can be accessed either locally through the RS-232 Terminal Port on the
management module or remotely from your network using the Telnet or
Secure Shell application protocol. To access the interface, you must log on
to the management module with a valid manager name and password.
Note
The first management session of the chassis must be from a local
management session. For instructions, refer to “Starting a Local
Management Session” on page 18.
Manager
Privilege Levels
The management software has three manager privilege levels:
ˆ
administrator
ˆ
read-write
ˆ
read-only
The privilege level of administrator is restricted to the management
module’s predefined manager account, which has the user name of
“manager” and the default password “friend.”
The management module can support ten additional manager accounts
with the privilege level of read-write and another ten accounts of read-only.
The read-write level is nearly identical to the administrator level of the
predefined manager account. It provides access to almost all of the same
parameters settings, with a few exceptions, detailed in Chapter 13,
“Manager Account Commands” on page 215. In contrast, the read-only
privilege level restricts a network administrator to just viewing the
parameter settings.
The privilege level required to perform a command is included in the
descriptions of the commands in this manual.
Note
Only the predefined manager account can have the privilege level of
administrator.
17
Chapter 1: Starting a Management Session
Starting a Local Management Session
Note
Local management sessions do not require an IP configuration on
the AT-MCF2000M Management Module.
To start a local management session on the chassis, perform the following
procedure:
1. Connect the DIN-8 connector on the RS-232 Serial Management
Cable included with the AT-MCF2000M Management Module to the
RS-232 Terminal port on the module, as shown in Figure 1.
AT-M
CF
2000
M
STACK
LINK
MANAG
ACT
EMENT
1000
LIN
TERMIN
ID
AL
K
ACT
10/100
LINK
ACT
0
PORT
31
RESET
10/100/1
000BAS
FDX
ACTIV HDX
ITY
BOOT
E-T
COL
RDY
FAUL
T
RS-232
AT-M
CF
2KFA
N
SD
RDY
BUSY
MASTE
R
POW
ER
STAT
US
NORM
FAUL AL
T
1261
Figure 1. Connecting the RS-232 Serial Management Cable to the RS-232
Terminal Port
2. Connect the other end of the cable to an RS-232 port on a terminal or
PC with a terminal emulator program.
3. Configure the terminal or terminal emulation program as follows:
ˆ
Baud rate: 115,200 bps (The RS-232 Terminal port has a baud
rate range of 9600 to 115,200 bps. The default is 115,200 bps. To
adjust the baud rate, refer to “SYSTEM SET ASYNCHRONOUS”
on page 58.)
ˆ
Data bits: 8
ˆ
Parity: None
ˆ
Stop bits: 1
ˆ
Flow control: None
Note
The port settings are for a DEC VT100 or ANSI terminal, or an
equivalent terminal emulator program.
18
AT-S85 and AT-S97 Management Software User’s Guide
Note
The prompt “Hit any key to stop autoboot,” displayed on the console
when the management module is reset or power cycled, is for
manufacturing purposes only and should be ignored. If you
inadvertently display the manufacturing prompt (=>), type “bootapp”
to launch the management software on the management module.
4. Press Enter.
You are prompted for a user name and password.
5. Enter a user name and password. The management module has a
predefined manager account with the privilege level of administrator.
The account provides unlimited access to all the parameters on the
management and media converter modules. To log in using this
account, enter “manager” as the user name. The default password for
the account is “friend.” The user name and password are case
sensitive.
After you have logged in, the management software displays the
command line interface, shown in Figure 2.
Allied Telesis Media Converter- Version 3.0.0
<No System Name>
#
Figure 2. Command Line Interface Prompt
The symbol in the command line prompt reflects the access level of
your manager account. The predefined manager account has the
pound symbol (#) prompt. A read-write or read-only account has a
dollar symbol ($) prompt. For information on the three manager
privilege levels of the AT-S97 Management Software, refer to
“Manager Privilege Levels” on page 17. For instructions on how to
change a password or create additional manager accounts, refer to
Chapter 13, “Manager Account Commands” on page 215.
You can now begin to manage the chassis. For suggestions on what to
configure during the initial configuration, refer to “What to Configure
First” on page 30.
19
Chapter 1: Starting a Management Session
Starting a Remote Telnet or Secure Shell Management Session
Review the following guidelines before starting a remote Telnet or Secure
Shell (SSH) management session:
ˆ
The AT-MCF2000M Management Module must have an IP
configuration. For instructions, refer to Chapter 3, “IP Configuration
Commands” on page 47.
ˆ
The 10/100/1000Base-T Management port on the management
module must be connected to a device on your network, such as a
Fast Ethernet or Gigabit Ethernet switch. Remote management
sessions with the management module are conducted through this
port.
ˆ
The Telnet server or SSH server on the management module must be
enabled. For instructions, refer to Chapter 10, “Telnet Server
Commands” on page 197 or Chapter 12, “Secure Shell Server (SSH)
Commands” on page 209.
ˆ
The remote Telnet or SSH client must be a member of the same
network as the management module or have access to it through
Layer 3 routing devices.
ˆ
If the management module and the remote Telnet or SSH client reside
on different networks, the IP configuration on the module must include
a default gateway address specifying the IP address of the routing
interface of the first hop to reaching the remote client. For instructions,
refer to Chapter 3, “IP Configuration Commands” on page 47.
ˆ
The management module can support 20 Telnet and 20 SSH
management sessions, simultaneously.
To start a remote Telnet or SSH management session, perform the
following procedure:
1. Enter the IP address of the AT-MCF2000M Management Module in the
Telnet or SSH client on the remote workstation.
The management software prompts you for a user name and
password.
2. Enter a user name and password. The management module has a
predefined manager account with the privilege level of administrator
and unlimited access to all of the parameters on the management and
media converter modules. To log in using this account, enter
“manager” as the user name. The default password for the account is
“friend.” The user name and password are case sensitive.
The local management session starts and the command line interface
prompt is displayed, as shown in Figure 2 on page 19.
20
AT-S85 and AT-S97 Management Software User’s Guide
For information on the three manager privilege levels of the AT-S97
Management Software, refer to “Manager Privilege Levels” on
page 17. For instructions on how to change a password or create
additional manager accounts, refer to Chapter 13, “Manager Account
Commands” on page 215.
The section “What to Configure First” on page 30 has suggestions on
what you should configure during the initial management session of
the chassis.
21
Chapter 1: Starting a Management Session
SNMP Management Session
You can also manage the AT-MCF2000 chassis remotely using an Simple
Network Management Protocol (SNMP) management program such as
HP Openview. This method, however, does not use the management
interface.
To manage the chassis from a management workstation using an SNMP
management program, you need to load the Management Information
Base (MIB) file, atMCF2000.mib, that was included with the AT-S85 and
AT-S97 software onto the management workstation. (The MIB file is
available from the Allied Telesis web site.)
This requires that you use a MIB compiler to compile the file. A familiarity
with MIB objects is necessary for this type of management. To load the
MIB file onto a management workstation, follow the instructions included
with your MIB compiler. For instructions on how to compile the MIB file
with your SNMP program, refer to your SNMP management
documentation.
To establish a SNMP management session for a unit that is remotely
managed, the chassis must have a management card and an IP address.
Before performing the SNMP management session, note the followings:
22
ˆ
The 10/100Base-TX port on the management card must be connected
to the network.
ˆ
The remote management workstation must reach the chassis through
the subnet of the management card.
AT-S85 and AT-S97 Management Software User’s Guide
Saving Your Configuration Changes
The configuration settings of the management and media converter
modules of a chassis or stack are stored in a series of files called
configuration files in the modules’ file systems. The most important of
these files is the active master configuration file on the management
module, which, as its name implies, contains all of the settings of a chassis
or stack. What the configuration files do is they retain the parameter
settings of the modules when a unit is power cycled or reset. Without the
files, you would have to reconfigure the modules whenever you reset a
device.
The modules do not automatically update their configuration files and the
active master configuration file when you change a device’s parameter,
such as the speed of a port on a media converter module. Instead, you
must initiate the update with the CONFIG SAVE command. This command
instructs all the modules in a chassis, or stack, to update their
configuration files to match their current settings. You should always
perform this command after adjusting the parameter settings of the
modules. Otherwise, your changes are discarded if you have to reset or
power cycle the unit.
Note
Many of the chapters in this guide have a note on the first page
reminding you to update the configuration files with the CONFIG
SAVE command after entering your parameter changes.
For further information on configuration files and the CONFIG SAVE
command, refer to Chapter 8, “Configuration File Commands” on page
145.
23
Chapter 1: Starting a Management Session
Quitting a Management Session
To quit a management session, enter Exit at the command prompt. You
should always exit from a management session when you are finished
managing a media converter. This can prevent unauthorized individuals
from making changes to a unit’s configuration if you leave your
management station unattended. For information about how to use the
console timer to automatically disconnect a management session, refer to
“SYSTEM SET CONSOLE” on page 62.
Note
Failure to properly exit from a management session may block
future management sessions until the console timer times out. For
information on the console timer, refer to “SYSTEM SET
CONSOLE” on page 62.
24
AT-S85 and AT-S97 Management Software User’s Guide
Chassis ID Numbers
As explained in the AT-MCF2000 Multi-channel Media Converter Series
Installation Guide, you can form a management stack of multiple chassis
by linking them together with the AT-MCF2000S Stacking Module. A
management stack makes managing the devices easier because you can
configure the units from the same management session from one
AT-MCF2000M Management Module.
When building a management stack you have to assign each of the
chassis a unique ID number. This number is set with a jumper on the
AT-MCF2000M Management Module and with the DIP switches on the
AT-MCF2000S Stacking Module. The AT-MCF2000M Management
Module can have a chassis ID number of 0 or 31 and the AT-MCF2000S
Stacking Module can have a chassis ID number of 1 to 30.
Chassis ID numbers are required in commands that have the chassis
parameter. This parameter is used to specify the ID number of the chassis
you want to configure with the command. If the chassis has the
management module, then its ID number will be either 0 or 31. (In all
likelihood, it’ll be 0, the default setting.) If the chassis is part of a
management stack and therefore has the AT-MCF2000S Stacking
Module, its chassis ID number will be in the range of 1 to 30. To determine
the ID number of a chassis with the AT-MCF2000S Stacking Module, view
the chassis ID LEDs on the front panel of the module or use the SYSTEM
SHOW CLUSTER command. For instructions, refer to “SYSTEM SHOW
CLUSTER” on page 101.
25
Chapter 1: Starting a Management Session
Slot Numbers and Letters
Some of the commands in the management software programs have a
slot parameter for specifying a slot in an enclosure. You use this
parameter to specify the slot that contains the module you want to
configure with a command. The slots for the media converter modules are
identified by numbers and the slots for the power supply modules and the
management module are identified by letters.
AT-MCF2KPNL1
AT-MCF2000
Figure 3 shows the numbers and letters for the slots in the AT-MCF2000
Chassis.
AT-MCF2KPNL1
2
1
Slot 1
Slot 2
A
MANAGEMENT
AT-MCF2KPNL2
B
AT-MCF2KPNL2
AT-MCF2KPNL3
Slot A
Slot M
Slot B
Figure 3. Slot Numbers and Letters for the AT-MCF2000 Chassis
Table 1 lists the purposes of the slots in the unit.
Table 1. AT-MCF2000 Chassis Slots
Slot
26
Module
1 and 2
These slots are for the multi-channel
AT-MCF2012LC, AT-MCF2012LC/1, and
AT-MCF2032SP Media Converter Modules.
A and B
These slots are for the AT-MCF2000AC Power
Supply Module and the AT-MCF2KFAN Module.
M
This slot is for the AT-MCF2000M Management
Module or the AT-MCF2000S Stacking Card.
AT-S85 and AT-S97 Management Software User’s Guide
Slot 1
AT-MCF2KPNL1
AT-MCF2000
Figure 4 shows the numbers and letters of the slots in the AT-MCF2300
Chassis.
AT-MCF2KPNL1
Slot 3
AT-MCF2KPNL1
Slot 4
AT-MCF2KPNL1
4
3
MANAGEMENT
A
AT-MCF2KPNL3
B
AT-MCF2KPNL3
AT-MCF2KPNL3
Slot A
Slot 2
2
1
Slot M
Slot B
Figure 4. Slot Numbers and Letters for the AT-MCF2300 Chassis
Table 2 lists the numbers and letters of the slots in the chassis.
Table 2. AT-MCF2300 Chassis Slots
Slot/Module
Module
1 to 4
These slots are for the multi-channel
AT-MCF2012LC, AT-MCF2012LC/1, and
AT-MCF2032SP Media Converter Modules.
A and B
These slots are for the AT-MCF2300AC Power
Supply Module.
M
This slot is for the AT-MCF2000M Management
Module or the AT-MCF2000S Stacking Card.
27
Chapter 1: Starting a Management Session
Command Line Interface Features
The command line interface supports the following features:
28
ˆ
Command history - You can scroll through a history of your commands
with the up and down arrow keys.
ˆ
Context-specific help - Typing a question mark against the command
line prompt displays a list of the command keywords. Additionally,
typing a question mark when entering a command displays a list of
legal parameters.
ˆ
Keyword abbreviations - Keywords can be recognized by typing an
unambiguous prefix, for example, “sy” for “system.”
ˆ
Tab key - Pressing the Tab key fills in the rest of the keyword. For
example, typing “mo” and pressing the Tab key enters “module.”
AT-S85 and AT-S97 Management Software User’s Guide
Command Formatting
The following formatting conventions are used in this manual:
ˆ
screen text font - This font illustrates the format of a command and
command examples.
ˆ
screen text font - Italicized screen text indicates a variable for you
to enter.
ˆ
[ ] - Brackets indicate optional parameters.
ˆ
| - Vertical line separates parameter options for you to choose from.
29
Chapter 1: Starting a Management Session
What to Configure First
This section has a few suggestions on what to configure during your first
management session. The initial management session must be a local
session. For instructions on how to start a local management session,
refer to “Starting a Local Management Session” on page 18.
Note
Although the management module comes with the default IP
address of 10.0.0.1 and subnet mask of 255.255.252.0, the initial
configuration must be a local session because the module’s Telnet
and SSH servers are initially disabled.
Displaying the
Chassis Modules
After logging on, enter this command:
system show cluster
The command is used to display and verify the management module and
the media converter modules in a chassis. An example is shown in Figure
5.
Chassis
Chassis
Chassis
MAC
Master
ID
Name
Type
Address
Chassis
-------------------------------------------------------------------------------------0
AT-MCF2000
11:22:33:44:55:55
Yes
AT-MCF2000
Slot ID
Module Name
Module Type
Cfg Overwrite Software Version
-----------------------------------------------------------------------------M
AT-MCF2000M
v3.0.0
1
AT-MCF2012LC
Disable
v3.0.0
2
AT-MCF2012LC/1
Disable
v3.0.0
Management and media converter module information
Chassis information
Figure 5. Displaying the Chassis Modules
30
AT-S85 and AT-S97 Management Software User’s Guide
If multiple chassis are linked together with the AT-MCF2000S Stacking
Module to form a stack, this command displays all of the enclosures and
the modules in the stack. Here is an example of a stack with three chassis.
Chassis
Chassis
Chassis
MAC
Master
ID
Name
Type
Address
Chassis
-------------------------------------------------------------------------0
AT-MCF2000
11:22:33:44:55:55
Yes
AT-MCF2000
Slot ID
Module Name
Module Type
Cfg Overwrite Software Version
---------------------------------------------------------------------M
AT-MCF2000M
v3.0.0
1
AT-MCF2012LC
Enable
v3.0.0
2
AT-MCF2012LC/1 Enable
v3.0.0
1
11:22:33:44:22:22
No
AT-MCF2000
Slot ID
Module Name
Module Type
Cfg Overwrite Software Version
---------------------------------------------------------------------1
AT-MCF2012LC
Disable
v3.0.0
2
AT-MCF2012LC
Disable
v3.0.0
2
11:22:33:44:66:77
No
AT-MCF2300
Slot ID
Module Name
Module Type
Cfg Overwrite Software Version
---------------------------------------------------------------------1
AT-MCF2012LC
Enable
v3.0.0
2
AT-MCF2012LC
Enable
v3.0.0
3
AT-MCF2012LC
Enable
v3.0.0
4
AT-MCF2012LC/1 Enable
v3.0.0
Figure 6. Displaying the Chassis Modules of a Stack
For information about this command, refer to “SYSTEM SHOW
CLUSTER” on page 101.
Note
To avoid possible compatibility problems between the management
module and the media converter modules, Allied Telesis
recommends that all of the modules in a chassis or stack use the
same version of the AT-S85 and AT-S97 Management Software. If
the modules shown in the SYSTEM SHOW CLUSTER command
have different versions, you should upgrade the operating software
on the modules. For instructions, Chapter 9, “File System
Commands” on page 169.
31
Chapter 1: Starting a Management Session
Changing the
Manager
Password
The default password for the predefined manager account is included in
this document, which is available on our web site. To protect the unit from
unauthorized access, you should change the password as part of the
initial configuration. To change the password, enter this command:
user set username=manager password
You are prompted to change the password. A password can be up to 16
alphanumeric characters and is case sensitive. Special characters,
including spaces, question marks, and quotation marks, are permitted.
You are prompted twice to verify the new password.
For information on how to create additional manager accounts, refer to
Chapter 13, “Manager Account Commands” on page 215.
Creating a
Master
Configuration
File
This step creates a master configuration file for storing your parameter
changes, in the file system on the management module. Without the file,
the management card cannot save your parameter settings and you’ll
have to reenter them if you reset or power cycle the chassis.
This task has two steps. In the first step you create the file with the
CONFIG SAVE FILESYSTEM command. The format of the command is:
config save filesystem=system://chassis/slot/filename.cfg
The chassis variable is the ID number of the chassis. A chassis with a
management module installed has a chassis ID of 0 or 31. This value is
set with a jumper on the circuit board of the module. The chassis ID of a
chassis with a stacking module is 1 through 30. The value is also set
manually on the stacking module.To view this number, use the SYSTEM
SHOW CLUSTER command.
The slot variable specifies the chassis slot that has the management
module, signified by the letter “m.”
And, finally, filename.cfg is the filename for the new master configuration
file. The name can be up to 15 alphanumeric characters, not including the
extension. Spaces are allowed, but a name with spaces must be enclosed
in double quotes.
This example of the command creates the new master configuration file
“mcf_chassis0.cfg”. The chassis with the management module has the ID
number 0:
config save filesystem=system://0/m/mcf_chassis0.cfg
For further information on this command, refer to “CONFIG SAVE
FILESYSTEM” on page 162.
32
AT-S85 and AT-S97 Management Software User’s Guide
Now that you have created the master configuration file, you’re ready to
perform the second step and designate it as the module’s active master
configuration file. This directs the management module to the appropriate
master configuration file when saving your changes. (In some cases, the
management module might have more than one master configuration file,
such as a history of past configuration files. But only one of the files can be
active at a time.) The command for designating the active master
configuration file is the CONFIG SET command. Here is the format:
config set filesystem=system://chassis/slot/filename.cfg
The definitions of the variables in this command are the same as in the
CONFIG SAVE FILESYSTEM command. Here is an example of the
command that designates the “mcf_chassis1.cfg” file created in the
previous command as the management module’s active configuration file:
config set filesystem=system://0/m/mcf_chassis1.cfg
Configuration filenames in both the CONFIG SAVE FILESYSTEM and
CONFIG SET commands are case sensitive. For more information on this
command, refer to “CONFIG SET” on page 164.
This completes the procedure for creating and designating a new active
master configuration file on the management module. The management
module can now save your parameter changes when you issue the
CONFIG SAVE command.
Assigning an IP
Address
Configuration
Will you be remotely managing the chassis with a Telnet or Secure Shell
(SSH) client? Or, will the management module be performing any of the
following management tasks?
ˆ
Uploading or downloading files to its file system from a TFTP server.
ˆ
Setting the date and time from a Network Time Protocol (NTP) server
ˆ
Sending events to a syslog server
ˆ
Sending or receiving TCP/IP ping requests from another network
device
ˆ
Managing the device with SNMP
If so, then you have to assign the management module an IP address, a
subnet mask, and possibly a default gateway address, referred to
collectively as a module’s IP address configuration.
An IP address configuration can be assigned manually or by a DHCP or
BOOTP server. The command to manually assign an IP configuration to
the management module is:
ip set ip-address=ipaddress subnetmask=mask
default-gateway=ipaddress
33
Chapter 1: Starting a Management Session
In this example, the management module is assigned the IP address
149.112.44.22, the subnet mask 255.255.255.0, and the default gateway
149.112.44.242:
ip set ip-address=149.112.44.22 subnetmask=255.255.255.0
default-gateway=149.112.44.242
For more information on this command, refer to “IP SET” on page 52.
If you want the management module to obtain its IP configuration from a
DHCP or BOOTP server on your network, activate the DHCP and BOOTP
clients with this command:
ip dhcp enable
(If you want the DHCP or BOOTP server to assign a static IP address
based on the module’s MAC address, you need to know that the
management module actually uses the chassis’ MAC address to
communicate with your network. To learn the chassis’ address, refer to
“DIAGNOSTICS SHOW CHASSIS” on page 230 or “SYSTEM SHOW
CLUSTER” on page 101.)
For more information on this commands, refer to “IP DHCP ENABLE” on
page 51.
Note
Be sure that the 10/100/1000Base-T Management port on the
management module is connected to your network before activating
the DHCP and BOOTP clients. The management module
communicates with your network through that port.
Setting the Date
and Time
The date and time are added to the event messages logged in its event
log and to SNMP traps. You can set the date and time manually or with a
Network Time Protocol (NTP) server on your network or the Internet. The
command for manually setting the date and time is:
system set clock date=mm/dd/yyyy time=hh:mm:ss
This example sets the date to April 11, 2007 and the time to 4:34 pm:
system set clock date=4/11/2007 time=16:34:0
To have an NTP server supply the date and time, specify the IP address of
the server and then activate the NTP client. Here is the command for
specifying the NTP server’s IP address:
ntp set server=ipaddress
The ipaddress variable is the IP address of the NTP server. This example
specifies the IP address of the NTP server as 149.122.55.77:
ntp set server=149.122.55.77
34
AT-S85 and AT-S97 Management Software User’s Guide
After specifying the server’s IP address, activate the NTP client with this
command:
ntp enable
Note
Review the section “NTP Client Guidelines” on page 118 before
activating the client.
Enabling the
Telnet or Secure
Shell Server
Do you want to be able to manage the chassis over your network from a
remote workstation with the Telnet or SSH application protocol? If so,
activate the appropriate server on the management module. To enable the
Telnet server, enter this command:
telnet enable
To enable the SSH server, enter this command:
ssh enable
For information of the Telnet server commands, refer to Chapter 10,
“Telnet Server Commands” on page 197. For information on the SSH
commands, refer to Chapter 12, “Secure Shell Server (SSH) Commands”
on page 209
Naming a Chassis
Assigning a name to a chassis will make identifying it in the management
software easier. It may also help you avoid the common mistake of
performing a command or procedure on the wrong device. The command
is SYSTEM SET CHASSIS and the format is:
system set chassis id=chassis name=name
The chassis variable is the ID number of the chassis. If you have a
management module installed in the chassis, the chassis id is either 0 (the
default) or 31. If you have a stacking module installed in your chassis, you
can assign a range of 1 to 30 as the chassis ID. To view this number, use
the SYSTEM SHOW CLUSTER command.
The name variable specifies a name of up to 20 alphanumeric characters
for the chassis. Spaces are allowed, but a name with spaces must be
enclosed in double quotes (“ “).
This example assigns the name “Region 1 Traffic” to a chassis with an ID
number of 1:
system set chassis id=1 name=”Region 1 Traffic”
For more information on the SYSTEM SET CHASSIS command, refer to
“SYSTEM SET CHASSIS” on page 59.
35
Chapter 1: Starting a Management Session
Saving Your
Changes
This completes the initial configuration of the chassis. To update the
configuration files on the modules with your changes, enter this command:
config save
For more information on the command, refer to “Saving Your
Configuration Changes” on page 23 or Chapter 8, “Configuration File
Commands” on page 145.
Note
If you do not issue the CONFIG SAVE command and later reset or
power cycle the device, your changes will be discarded.
Note
To make identifying the chassis easier, Allied Telesis recommends
attaching a label to the front panel of the unit with its chassis ID
number, name, and MAC address. To view this information, use the
SYSTEM SHOW CLUSTER command.
36
AT-S85 and AT-S97 Management Software User’s Guide
Replacing a Media Converter Module
To replace a module:
1. Install the new module in the chassis. For instructions, refer to the
AT-MCF2300 Multi-channel Media Converter Series Installation Guide.
2. Wait one minute for the module to initialize its management software.
3. Start a local or remote management session on the chassis or stack.
For instructions, refer to “Starting a Local Management Session” on
page 18 or “Starting a Remote Telnet or Secure Shell Management
Session” on page 20.
4. Enter this command:
system show cluster
5. Examine in the display the configuration overwrite setting of the media
converter module you just installed.
Configuration
Overwrite Setting
Chassis
Chassis
Chassis
MAC
Master
ID
Name
Type
Address
Chassis
-------------------------------------------------------------------------------------0
AT-MCF2000
11:22:33:44:55:55
Yes
AT-MCF2000
Slot ID
Module Name
Module Type
Cfg Overwrite Software Version
-----------------------------------------------------------------------------M
AT-MCF2000M
v3.0.0
1
AT-MCF2012LC
Disable
v3.0.0
2
AT-MCF2012LC/1
Disable
v3.0.0
Figure 7. Determining the Configuration Overwrite Setting of a Media
Converter Module
ˆ
If the overwrite setting is enabled, the module seeks its
configuration from the management module and the master
configuration file. If the media converter module that previously
occupied the slot was the same model, than the new module is
assigned the very same configuration settings, automatically. If the
slot had not been used before or if the previous module was a
different model, the newly installed module uses its own auxiliary
configuration file in flash memory to set its parameters, or if it has
never been used before, it uses the default values.
37
Chapter 1: Starting a Management Session
ˆ
If the overwrite setting for the new module is disabled, the module
configures its settings using its own auxiliary configuration file in
flash memory. If you want the new module to use the same
configuration settings as the module previously installed in the slot,
you can use the CONFIG RUN command. For instructions, refer to
“CONFIG RUN” on page 160.
For background information about the overwrite setting, refer to “Media
Converter Modules and Auxiliary Configuration Files” on page 146.
38
Chapter 2
Basic Commands
This chapter contains the following commands:
ˆ
“‘?’ Question Mark Key” on page 40
ˆ
“CLEAR” on page 41
ˆ
“EXIT” on page 42
ˆ
“HELP” on page 43
ˆ
“PING” on page 44
39
Chapter 2: Basic Commands
‘?’ Question Mark Key
Syntax
?
Parameters
None.
Privilege Levels
Administrator, read-write, and read-only.
Description
Entering a question mark at the command line prompt displays a list and a
brief description of the command line keywords. Entering a question mark
after a keyword displays the available keyword parameters. Additionally,
entering a question mark after a parameter displays the parameter’s class
(that is, integer, string, etc.).
Examples
This command lists all of the command keywords:
?
This command displays the available parameters for the CONFIG
keyword:
config ?
This command displays the class of the value for the SET parameter in the
CONFIG command:
config set?
40
AT-S85 and AT-S97 Management Software User’s Guide
CLEAR
Syntax
clear
Parameters
None.
Privilege Levels
Administrator, read-write, and read-only.
Description
This command clears the screen.
Example
clear
41
Chapter 2: Basic Commands
EXIT
Syntax
exit
Parameters
None.
Privilege Levels
Administrator, read-write, and read-only.
Description
This command ends a management session.
Example
exit
42
AT-S85 and AT-S97 Management Software User’s Guide
HELP
Syntax
help
Parameters
None.
Privilege Levels
Administrator, read-write, and read-only.
Description
This command displays information about how you can use the “?” and tab
keys to simplify the entry of commands.
Example
help
43
Chapter 2: Basic Commands
PING
Syntax
ping ipaddress
Parameter
ipaddress
Specifies the IP address of the device to ping.
Privilege Levels
Administrator and read-write.
Description
This command is used to test for a network connection between the
management module and a remote device on your network. If the
management module is experiencing a problem communicating with a
network device, such as a syslog server or a TFTP server, this command
could prove useful in troubleshooting the problem. You could use it to
determine whether a valid network link exists between the module and the
other device.
The command sends three TCP/IP ping requests and displays the results
of the requests on your workstation.
Here are the guidelines to using this command:
44
ˆ
The management module must have an IP configuration. For
instructions, see Chapter 3, “IP Configuration Commands” on page 47.
ˆ
The 10/100/1000Base-T Management port on the management
module must be connected to a device on your network, such as an
Ethernet switch. The ping requests are transmitted only from that port
and not from the ports on the media converter modules.
ˆ
The management module must be a member of the same subnet as
the remote device or have access to the device’s subnet through
routers or other Layer 3 routing devices.
ˆ
If the management module and the remote device are members of
different networks, the IP configuration on the module must include a
default gateway address that specifies the IP address of the routing
interface of the first hop to reaching the device. For instructions, refer
to Chapter 3, “IP Configuration Commands” on page 47.
AT-S85 and AT-S97 Management Software User’s Guide
Example
This command has the management module send three ping requests to a
remote device with an IP address of 149.12.55.77:
ping 149.12.55.77
45
Chapter 2: Basic Commands
46
Chapter 3
IP Configuration Commands
This chapter contains the following sections:
ˆ
“Overview” on page 48
ˆ
“IP DHCP DISABLE” on page 50
ˆ
“IP DHCP ENABLE” on page 51
ˆ
“IP SET” on page 52
ˆ
“IP SHOW” on page 54
Note
Remember to save your parameter changes in the active master
configuration file with the CONFIG SAVE command. For information,
refer to “Saving Your Configuration Changes” on page 23 or Chapter
8, “Configuration File Commands” on page 145.
47
Chapter 3: IP Configuration Commands
Overview
The IP commands are used to assign an IP address configuration,
consisting of an IP address, subnet mask, and default gateway address, to
the AT-MCF2000M Management Module. The management module must
have an IP address configuration to perform these functions:
ˆ
Supporting remote management using a Telnet or Secure Shell (SSH)
client.
ˆ
Supporting remote management using the Simple Network
Management Protocol (SNMP)
ˆ
Uploading or downloading files to its file system from a TFTP server
ˆ
Setting the date and time from a Network Time Protocol (NTP) server
ˆ
Sending events to a syslog server
ˆ
Sending or receiving TCP/IP ping requests from network devices
The address configuration must include a default gateway address if the
management module will be communicating with network devices on
different subnets or networks than itself. The address, which must be a
member of the same network as the management module, must identify
the routing interface of the first hop to reaching the remote devices. For
example, the module must have a default gateway address if:
ˆ
You will be managing the unit remotely from a Telnet client on a
different network from the management module.
ˆ
If the unit’s date and time will be set from an NTP server on another
network.
The IP address configuration can be assigned manually or from a DHCP
or BOOTP server on your network. To assign the configuration manually,
use the IP SET command. To assign the configuration from a DHCP and
BOOTP server, use the IP DHCP ENABLE command to activate the
DHCP and BOOTP clients.
All communications between the management module and your network
are conducted through the 10/100/1000Base-T Management port.
Consequently, this port must be connected to a network device, such as a
Fast Ethernet or Gigabit Ethernet switch. The AT-MCF2000M
Management Module cannot communicate with your network through the
ports on the media converter modules in the chassis.
Note
The media converter modules operate independently of the
AT-MCF2000M Management Module. As such, their operations are
not affected if the management module does not have an IP address
configuration.
48
AT-S85 and AT-S97 Management Software User’s Guide
Command
Summary
Table 3 summarizes the IP configuration commands.
Table 3. IP Configuration Commands
Command
Description
IP DHCP DISABLE on
page 50
Deactivates the DHCP and
BOOTP clients on the
management module.
IP DHCP ENABLE on page 51
Activates the DHCP and BOOTP
clients on the management
module.
IP SET on page 52
Manually sets the IP configuration.
IP SHOW on page 54
Displays the IP address, subnet
mask, and default gateway of the
management module.
49
Chapter 3: IP Configuration Commands
IP DHCP DISABLE
Syntax
ip dhcp disable
Parameters
None.
Privilege Levels
Administrator and read-write.
Description
This command is used to deactivate the DHCP and BOOTP clients on the
management module. When the clients are deactivated, which is their
default setting, the default values are reinstituted for the module’s IP
address.
To manually assign an IP address to the management module, refer to “IP
SET” on page 52.
Example
ip dhcp disable
50
AT-S85 and AT-S97 Management Software User’s Guide
IP DHCP ENABLE
Syntax
ip dhcp enable
Parameters
None.
Privilege Levels
Administrator and read-write.
Description
This command is used to activate the management module’s DHCP and
BOOTP clients so as to obtain an IP address configuration from a DHCP
or BOOTP server on your network. For background information on when to
assign the management module an IP address, refer to “Overview” on
page 48.
When the clients are activated, the management module queries first for a
DHCP server. If it receives a response, it applies the IP address
configuration from the server to its IP parameters, and stops querying the
network. If there is no response after seven attempts, the management
module queries for a BOOTP server. If there is again no response, the
management module stops its query efforts.
The default setting for the DHCP and BOOTP clients is disabled.
Note
If an IP address was manually assigned to the module, it is
overwritten by the values from the DHCP or BOOTP server.
The management module must communicate with a DHCP or BOOTP
server through its 10/100/1000Base-T Management port. The module
cannot communicate with your network through the ports on the media
converter modules in the chassis.
Example
ip dhcp enable
51
Chapter 3: IP Configuration Commands
IP SET
Syntax
ip set ip-address=ipaddress subnetmask=mask
default-gateway=ipaddress
Parameters
ip-address
Specifies an IP address for the AT-MCF2000M
Management Module. The default value is 10.0.0.1.
subnetmask
Specifies a subnet mask for the management module’s IP
address. The mask can be of variable length. The default
value is 255.255.252.0.
default-gateway
Specifies a default gateway for the management module.
The default gateway must be a member of the same subnet
as the module’s IP address. The default value is 0.0.0.0.
Privilege Levels
Administrator and read-write.
Description
This command is used to manually assign an IP address, subnet mask,
and default gateway address to the AT-MCF2000M Management Module.
For background information on when the module needs an IP address
configuration, refer to “Overview” on page 48.
Note
If the DHCP and BOOTP clients on the management module are
enabled, you must disable them with the IP DHCP DISABLE
command before using this command. For information on the
command, refer to “IP DHCP DISABLE” on page 50. To determine
the status of the clients, refer to “IP SHOW” on page 54.
Examples
This command assigns the IP address 149.22.67.8, subnet mask
255.255.255.224, and default gateway 149.22.67.247 to the
AT-MCF2000M Management Module:
ip set ip-address=149.22.67.8 subnetmask=255.255.255.224
default-gateway=149.22.67.247
52
AT-S85 and AT-S97 Management Software User’s Guide
This command assigns the default gateway address 149.44.55.22 to the
management module:
ip set default-gateway=149.44.55.22
This command removes the current IP address and subnet mask values
without assigning new values:
ip set ip-address=0.0.0.0 subnetmask=0.0.0.0
53
Chapter 3: IP Configuration Commands
IP SHOW
Syntax
ip show
Parameters
None.
Privilege Levels
Administrator, read-write, and read-only.
Description
This command is used to view the management module’s IP address,
subnet mask, and default gateway address. An example is shown in
Figure 8.
IP Information:
IP Address........... 149.25.42.11
Subnet Mask.......... 255.255.255.0
Gateway.............. 149.25.42.27
DHCP................... Disable
Figure 8. IP SHOW Command
For further information, refer to the following sections:
ˆ
“Overview” on page 48 for background information on when to assign
an IP address configuration to the management module.
ˆ
“IP DHCP ENABLE” on page 51 and “IP DHCP DISABLE” on page 50
for instructions on how to activate or deactivate the DHCP and BOOTP
clients.
ˆ
“IP SET” on page 52 for instructions on how to manually assign these
values.
Example
ip show
54
Chapter 4
General System Commands
This chapter contains the following sections:
ˆ
“Overview” on page 56
ˆ
“SYSTEM SET ASYNCHRONOUS” on page 58
ˆ
“SYSTEM SET CHASSIS” on page 59
ˆ
“SYSTEM SET CLOCK” on page 60
ˆ
“SYSTEM SET CONSOLE” on page 62
ˆ
“SYSTEM SET CONTACT” on page 63
ˆ
“SYSTEM SET HOSTNAME” on page 64
ˆ
“SYSTEM SET LOCATION” on page 65
ˆ
“SYSTEM SHOW ASYNCHRONOUS” on page 66
ˆ
“SYSTEM SHOW CLOCK” on page 67
ˆ
“SYSTEM SHOW CONSOLE” on page 68
ˆ
“SYSTEM SHOW INFO” on page 69
Note
Remember to save your parameter changes in the active master
configuration file with the CONFIG SAVE command. For information,
refer to “Saving Your Configuration Changes” on page 23 or Chapter
8, “Configuration File Commands” on page 145.
55
Chapter 4: General System Commands
Overview
The system commands are divided into two groups in this manual. The
first set of commands, described in this chapter, control and display the
basic parameters on the management module, such as the chassis’ name
and the date and time.
The commands in the second group control the individual ports and
channels on the media converter modules. These functions include setting
port parameters, such as speed and duplex mode, resetting media
converter modules, and displaying status information on the modules in a
chassis or stack. The system commands in this group are described in
Chapter 5, “Port and Module Commands” on page 71.
Command
Summary
Table 4 summarizes the general system commands described in this
chapter.
Table 4. General System Configuration Commands
Command
56
Description
“SYSTEM SET
ASYNCHRONOUS” on
page 58
Sets the baud rate of the RS-232
Terminal port on the management
module.
“SYSTEM SET CHASSIS” on
page 59
Assigns a name to a chassis.
“SYSTEM SET CLOCK” on
page 60
Manually sets the date and time.
“SYSTEM SET CONSOLE” on
page 62
Sets the console timeout
parameter for ending inactive
management sessions.
“SYSTEM SET CONTACT” on
page 63
Identifies the network
administrator responsible for
maintaining the chassis or stack.
“SYSTEM SET HOSTNAME”
on page 64
Specifies a name for the stack.
“SYSTEM SET LOCATION”
on page 65
Specifies the location of the stack.
“SYSTEM SHOW
ASYNCHRONOUS” on
page 66
Displays the baud rate of the RS232 Terminal port on the
management module.
“SYSTEM SHOW CLOCK” on
page 67
Displays the date and time.
AT-S85 and AT-S97 Management Software User’s Guide
Table 4. General System Configuration Commands
Command
Description
“SYSTEM SHOW CONSOLE”
on page 68
Displays the console timeout
parameter.
“SYSTEM SHOW INFO” on
page 69
Displays the stack’s name, the
name of the network administrator
responsible for managing the
units, and the location of the stack.
57
Chapter 4: General System Commands
SYSTEM SET ASYNCHRONOUS
Syntax
system set asynchronous baudrate=2400|4800|9600|19200|115200
Parameters
baudrate
Specifies the new baud rate of the RS-232 Terminal port on
the AT-MCF2000M Management Module. The default is
115,200 bits per second (bps).
Privilege Levels
Administrator and read-write.
Description
This command is used to change the baud rate of the RS-232 Terminal
port on the AT-MCF2000M Management Module. The port is used to
locally manage the chassis. To view the port’s current baud rate setting,
refer to “SYSTEM SHOW ASYNCHRONOUS” on page 66.
Note
If you change the baud rate of the RS-232 Terminal port on the
management module while conducting a local management
session, the session is interrupted. To resume managing the
module, change the speed of the terminal or the terminal emulator
program to the new speed of the RS-232 Terminal port.
The other settings of the RS-232 Terminal port listed here are not
adjustable:
ˆ
Data bits: 8
ˆ
Parity: None
ˆ
Stop bits: 1
ˆ
Flow control: None
Example
This command sets the baud rate of the RS-232 Terminal port to 2,400
bps:
system set asynchronous baudrate=2400
58
AT-S85 and AT-S97 Management Software User’s Guide
SYSTEM SET CHASSIS
Syntax
system set chassis id=chassis name=name
Parameters
id
Identifies an ID number of a chassis you want to assign a
new name. The range is 0 to 31. To view an ID number of a
chassis, refer to “SYSTEM SHOW CLUSTER” on
page 101. For background information, refer to “Chassis ID
Numbers” on page 25.
name
Specifies a new name for a chassis. A name can be up to
20 alphanumeric characters. Spaces are permitted, but
names with spaces must be enclosed in double quotes (“ “).
To remove the current value without specifying a new
value, enter “none”.
Privilege Levels
Administrator and read-write.
Description
This command is used to assign a name to a chassis. Identifying the
different AT-MCF2000 and AT-MCF2300 Chassis in the management
software will be easier if you give them names.
The difference between this command and the SYSTEM SET
HOSTNAME command is that this command is used to assign names to
the individual units in a stack while the latter command is used to assign
names to entire stacks.
To view the current name of a chassis, refer to “SYSTEM SHOW
CHASSIS” on page 99 or “SYSTEM SHOW CLUSTER” on page 101.
Examples
This command assigns the name “interconnect51” to the chassis with the
ID number 0:
system set chassis id=0 name=interconnect51
This command assigns the name “wtc connection” to the chassis with the
ID number 2:
system set chassis id=2 name="wtc connection"
59
Chapter 4: General System Commands
SYSTEM SET CLOCK
Syntax
system set clock date=mm/dd/yyyy time=hh:mm:ss
Parameters
date
Specifies the new date in month/day/year format. The
month and day must each be represented by two digits and
the year by four digits. For example, the date May 2, 2008
is entered as 05/02/2008.
time
Specifies the new time in 24-hour, hour:minute:second
format. Each part must have two digits and you have to
include all three parts. For example, 9:05 am is entered as
09:05:00.
Privilege Levels
Administrator and read-write.
Description
This command is used to manually set the date and time, which the
management module adds to the event messages and the SNMP traps.
With its onboard battery, the module is able to maintain the date and time
even when it is reset or powered off.
To view the current date and time, see “SYSTEM SHOW CLOCK” on
page 67.
To set the date and time using an Network Time Protocol (NTP) server,
refer to Chapter 6, “Network Time Protocol Commands” on page 117.
Note
If you activate the NTP client after setting the date and time
manually, the information from the NTP server will overwrite the
manually set date and time.
You do not have to enter the CONFIG SAVE command to save the new
date and time.
Examples
This command sets the date to April 11, 2007 and time to 4:34 pm:
system set clock date=04/11/2007 time=16:34:00
60
AT-S85 and AT-S97 Management Software User’s Guide
This command sets the time to 7:08 am and 25 seconds:
system set clock time=07:08:25
61
Chapter 4: General System Commands
SYSTEM SET CONSOLE
Syntax
system set console timeout=value
Parameter
timeout
Specifies the console timer in minutes. The range is 0 to 60
minutes. The default is 10 minutes.
Privilege Levels
Administrator and read-write.
Description
This command is used to set the console timer. This parameter controls
the amount of time (in minutes) the management software waits before it
automatically ends inactive local and remote management sessions. If
there is no management activity for the duration of the timer, the
management module automatically logs off the management session. This
security feature is used to prevent unauthorized individuals from using
your management station to alter the configuration settings of the media
converter chassis if you step away from your system during a
management session.
A value of 0 (zero) disables the console timer so that inactive
management sessions are never timed out. This value should be used
with caution. If you disable the console timer, you must remember to
always log off after every local and remote management session of the
media converter. Otherwise. future management sessions may be
blocked.
To view the current console timer setting, refer to “SYSTEM SHOW
CONSOLE” on page 68.
Note
The console timer is independent of the management module’s date
and time and operates regardless of whether the date and time are
set.
Example
This command sets the console timer to 25 minutes:
system set console timeout=25
62
AT-S85 and AT-S97 Management Software User’s Guide
SYSTEM SET CONTACT
Syntax
system set contact=contact
Parameter
contact
Specifies the name of the network administrator who has
the responsibility of maintaining the chassis. The contact
can be up to 25 alphanumeric characters. Spaces are
allowed, but names with spaces must be enclosed in
double quotes (“ “). To remove the current value without
specifying a new value, enter “none.”
Privilege Levels
Administrator and read-write.
Description
This command is used to set the name of the network administrator who is
responsible for managing the chassis. To view this parameter’s current
value, refer to “SYSTEM SHOW INFO” on page 69.
Example
This command sets the chassis’ contact to “Jane Smith:”
system set contact="Jane Smith"
63
Chapter 4: General System Commands
SYSTEM SET HOSTNAME
Syntax
system set hostname=name
Parameter
hostname
Specifies a name of up to 25 alphanumeric characters for a
stack. A host name is also used as the command line
prompt. Spaces are permitted, but a host name with
spaces must be enclosed in double quotes (“ “). To remove
the current value without specifying a new value, enter
“none.”
Privilege Levels
Administrator and read-write.
Description
This command is used to assign a name to a stack. The name is displayed
at the top of the console screen during management sessions. The first
fourteen characters of the host name are also used as the command line
prompt in the management interface.
To view the current value for this parameter, examine the top of the
console screen or the command line prompt. Or, refer to “SYSTEM SHOW
INFO” on page 69.
To assign individual names to the chassis in a stack, refer to “SYSTEM
SET CHASSIS” on page 59.
Examples
This command sets a stack’s name to “MCF2000 12a traffic:”
system set hostname="MCF2000 12a traffic"
This command removes a stack’s name without assigning a new value:
system set hostname=none
64
AT-S85 and AT-S97 Management Software User’s Guide
SYSTEM SET LOCATION
Syntax
system set location=location
Parameters
location
Specifies a location for a chassis or stack. A location can
be of up to 25 alphanumeric characters. Spaces are
allowed, but a location with spaces must be enclosed in
double quotes (“ “). To remove the current value without
specifying a new value, enter “none.”
Privilege Levels
Administrator and read-write.
Description
This command is used to specify a location of a chassis or stack. This
information can be helpful in locating the different media converter units in
your network. To view the current value for this parameter, refer to
“SYSTEM SHOW INFO” on page 69.
Examples
This command sets a stack’s location to “Bldg 3, rm 212:”
system set location="Bldg 3, rm 212"
This command removes the current location without assigning a new
value:
system set location=none
65
Chapter 4: General System Commands
SYSTEM SHOW ASYNCHRONOUS
Syntax
system show asynchronous
Parameters
None.
Privilege Levels
Administrator, read-write, and read-only.
Description
This command is used to display the baud rate setting of the management
module’s RS-232 Terminal port, which is used to locally manage a media
converter chassis or stack. An example of the information displayed by the
command is shown in Figure 9.
Asynchronous Port (Console) Information:
Baud Rate ............................ 115200
Figure 9. SYSTEM SHOW ASYNCHRONOUS Command
To configure the port’s baud rate, refer to “SYSTEM SET
ASYNCHRONOUS” on page 58.
Example
system show asynchronous
66
AT-S85 and AT-S97 Management Software User’s Guide
SYSTEM SHOW CLOCK
Syntax
system show clock
Parameters
None
Privilege Levels
Administrator, read-write, and read-only
Description
This command is used to display the current date and time on the
management module. An example of the information is shown in
Figure 10. The Real Time Clock (RTC) Source field indicates the source of
the date and time. The field will be “none” if the date and time were set
manually. If they were set by an NTP server, the RTC Source field will be
“NTP.”
System Clock Information
Date ............. 06/04/2007
Time ............. 03:35:25
RTC Source ....... none
Figure 10. SYSTEM SHOW CLOCK Command
To manually set the date and time, refer to “SYSTEM SET CLOCK” on
page 60. To set the date and time from an Network Time Protocol (NTP)
server, refer to Chapter 6, “Network Time Protocol Commands” on page
117.
Example
system show clock
67
Chapter 4: General System Commands
SYSTEM SHOW CONSOLE
Syntax
system show console
Parameters
None.
Privilege Levels
Administrator, read-write, and read-only.
Description
This command is used to display the setting for the console timer. This
parameter controls the amount of time (in minutes) that the management
software waits before it automatically ends an inactive local or remote
management session. The management software automatically logs off
the session if the console timer expires without any management activity.
This security feature prevents unauthorized individuals from using your
management station to change the configuration of the media converter
chassis should you step away from your system during a management
session.
A value of 0 (zero) disables the console timer. Inactive management
sessions are never timed out. This value should be used with caution. If
you disable the console timer, you must always remember to log off after
every local or remote management session of the media converter, or
future management session may be blocked.
To set the console timer setting, refer to “SYSTEM SET CONSOLE” on
page 62.
Example
system show console
68
AT-S85 and AT-S97 Management Software User’s Guide
SYSTEM SHOW INFO
Syntax
system show info
Parameters
None.
Privilege Levels
Administrator, read-write, and read-only.
Description
This command is used to display the stack’s name, the name of the
network administrator responsible for managing the units, and the location
of the stack. An example is shown in Figure 11.
System Information
Hostname ............ Engineering MCF
Contact ............. Jane Smith
Location ............ Bldg 3, Fl 1, Closet 122
Figure 11. SYSTEM SHOW INFO Command
To configure these parameters, see the following commands:
ˆ
“SYSTEM SET HOSTNAME” on page 64
ˆ
“SYSTEM SET CONTACT” on page 63
ˆ
“SYSTEM SET LOCATION” on page 65.
Example
system show info
69
Chapter 4: General System Commands
70
Chapter 5
Port and Module Commands
This chapter contains the following sections:
ˆ
“Overview” on page 72
ˆ
“SYSTEM RESET CHASSIS” on page 74
ˆ
“SYSTEM RESET CLUSTER” on page 76
ˆ
“SYSTEM RESET MODULE” on page 78
ˆ
“SYSTEM SET INTERFACE” on page 81
ˆ
“SYSTEM SET INTERFACE PORTNAME” on page 87
ˆ
“SYSTEM SET MODULE” on page 89
ˆ
“SYSTEM SET PORT” on page 92
ˆ
“SYSTEM SHOW CHASSIS” on page 99
ˆ
“SYSTEM SHOW CLUSTER” on page 101
ˆ
“SYSTEM SHOW INTERFACE” on page 103
ˆ
“SYSTEM SHOW MODULE” on page 111
Note
Remember to save your parameter changes in the active master
configuration file with the CONFIG SAVE command. For information,
see “Saving Your Configuration Changes” on page 23 or Chapter 8,
“Configuration File Commands” on page 145.
71
Chapter 5: Port and Module Commands
Overview
The system commands are divided into two groups in this manual. The
first group of commands, described in Chapter 4, “General System
Commands” on page 55, are used to display and control the basic
parameters on the management module, such as the chassis’ name and
the date and time.
The system commands that are described in this chapter control the
parameters on the ports and channels on the media converter modules.
These functions include setting port speed and duplex mode, resetting
media converter modules, and displaying status information about the
modules of a chassis.
Command
Summary
72
Table 5 summarizes the port and module configuration commands.
Table 5. Port and Module Commands
Command
Description
“SYSTEM RESET CHASSIS”
on page 74
Performs a soft reset on the
management module and media
converter modules in a chassis by
initializing their management
software.
“SYSTEM RESET CLUSTER”
on page 76
Restores the default settings to
the parameter settings on the
management module and the
media converter modules in a
chassis or stack.
“SYSTEM RESET MODULE”
on page 78
Performs a soft reset on individual
modules in a chassis by initializing
the module’s management
software.
“SYSTEM SET INTERFACE”
on page 81
Sets the operating mode of the
channels on a media converter
module.
“SYSTEM SET MODULE” on
page 89
Assigns a name and temperature
threshold to a module.
“SYSTEM SET PORT” on
page 92
Configures the parameter settings
of the ports in a media converter
channel.
AT-S85 and AT-S97 Management Software User’s Guide
Table 5. Port and Module Commands (Continued)
Command
Description
“SYSTEM SHOW CHASSIS”
on page 99
Displays the model names and
slot assignments of the
management and media converter
modules in a chassis, as well as
the chassis’ module name and
MAC address.
“SYSTEM SHOW CLUSTER”
on page 101
Displays the model names and
slot assignments of the
management and media converter
modules in the chassis of a stack,
as well as the chassis’ module
names and MAC addresses.
“SYSTEM SHOW
INTERFACE” on page 103
Displays the parameter settings of
the ports of the channels on a
media converter module.
“SYSTEM SHOW MODULE”
on page 111
Displays status information about
the media converter, power
supply, fan, and management
modules in the chassis.
Note
The SYSTEM RESET CHASSIS, SYSTEM RESET CLUSTER and
SYSTEM RESET MODULE commands may interrupt the flow of
network traffic through the ports and channels of the media
converter modules in a chassis or stack. Review the information in
the command descriptions before performing these commands.
73
Chapter 5: Port and Module Commands
SYSTEM RESET CHASSIS
Syntax
system reset chassis id=chassis
Parameters
id
Specifies an ID number of a chassis to reset. The range is
0 to 31. To view the ID number of a chassis, refer to
“SYSTEM SHOW CLUSTER” on page 101. For
background information, refer to “Chassis ID Numbers” on
page 25.
Privilege Levels
Administrator and read-write.
Description
This command is used to reset and initialize all of the media converter
modules in a chassis. If the chassis contains the AT-MCF2000M
Management Module, the command also resets and initializes that module
as well. You might reset a chassis if you are experiencing problems with
its modules.
Note
This command does not display a confirmation prompt. The
modules are reset as soon as you enter the command.
Note
Resetting the media converter modules may result in the loss of
some network traffic.
Note
A media converter module will immediately resume forwarding
network traffic through its ports and channels when it is reset. It uses
the default settings for its parameter settings as it initializes its
management software, which takes approximately one minute.
During the initialization process, it will be unresponsive to
management commands. Afterwards, the module will configure its
ports and channels according to the settings in either its own
configuration file or the active master configuration file on the
management module, depending on the configuration overwrite
setting for the slot.
74
AT-S85 and AT-S97 Management Software User’s Guide
Note
When the AT-MCF2000M Management Module is reset, it will be
unresponsive to commands for approximately one minute while it
initializes its AT-S97 Management Software.
Review the following before performing this command:
ˆ
The command does not affect the power supply and fan modules.
ˆ
If the chassis you’re resetting has the management module, you’ll
have to reestablish your management session after the module has
initialized its AT-S97 Management Software, if you want to continue to
manage the unit. The initialization process takes approximately one
minute to complete.
Note
Any parameter settings that you have not saved in the active master
configuration file on the management module are discarded during
the reset. To save your changes, use the CONFIG SAVE command.
For instructions, refer to “CONFIG SAVE” on page 161.
ˆ
To reset individual modules, refer to “SYSTEM RESET MODULE” on
page 78.
Examples
This command resets the chassis with the ID number 0:
system reset chassis id=0
This command resets the chassis with the ID number 2:
system reset chassis id=2
75
Chapter 5: Port and Module Commands
SYSTEM RESET CLUSTER
Syntax
system reset cluster
Parameters
None.
Privilege Level
Administrator.
Description
This command is used to restore the default values to the parameter
settings on the management module and all of the media converter
modules in the chassis or stack.
Note
This command should be used with caution. It deletes all of the
master and auxiliary configuration files in the file systems of the
modules. To retain a master configuration file on the management
module, upload it to a TFTP server before issuing this command.
For instructions, refer to “FILE UPLOAD” on page 194.
Note
The command resets all of the media converter modules in the
chassis or stack. Some network traffic may be discarded by the
modules.
Note
The management module will be unresponsive to commands for
approximately one minute while it initializes the AT-S97
Management Software.
Note
The media converter modules in the chassis will immediately
resume forwarding network traffic through their ports and channels
using the default settings for their parameter settings. However, they
will be unresponsive to management commands for approximately
one minute while they initialize their AT-S85 Management Software.
76
AT-S85 and AT-S97 Management Software User’s Guide
After you’ve performed this command, you must do the following before
you can save new parameter changes:
1. Create a new master configuration file on the management module or
download a previously saved file to the module from a TFTP server. To
create a new file, refer to “Creating a Master Configuration File” on
page 32 or “CONFIG SAVE FILESYSTEM” on page 162. To download
a configuration file from a TFTP server, refer to “FILE DOWNLOAD” on
page 179.
2. Designate the file as the management module’s active master
configuration file. For instructions, refer to “CONFIG SET” on
page 164.
3. If you downloaded a new master configuration file onto the
management module from a TFTP server and want to configure the
modules using the parameter settings in the file, issue the CONFIG
RUN command. For instructions, refer to “CONFIG RUN” on page 160.
Review the following before performing this command:
ˆ
The current date and time are retained.
ˆ
The command does not affect the power supply or fan modules.
ˆ
This command ends your management session. To continue
managing the unit, start a new session after the management module
initializes its AT-S97 Management Software. The initialization process
takes approximately one minute.
Example
This command restores the default settings to all of the management and
media converter modules in the chassis or stack by deleting all of the
master and auxiliary configuration files on the modules:
system reset cluster
77
Chapter 5: Port and Module Commands
SYSTEM RESET MODULE
Syntax
system reset module id=chassis/slot
Parameters
id
Identifies a media converter module or management
module to be reset. An ID number has the following parts:
chassis
Identifies an ID number of a chassis. The range
is 0 to 31. For background information, refer to
“Chassis ID Numbers” on page 25.
slot
Identifies the module to be reset by its slot
number or letter. For background information,
refer to “Slot Numbers and Letters” on page 26.
Possible values are:
1 or 2
Specifies a slot number of a media
converter module in the
AT-MCF2000 Chassis. The left slot
is 1 and the right slot is 2.
1 to 4
Specifies a slot number of a media
converter module in the
AT-MCF2300 Chassis. The slots are
number 1 (left) and 2 (right) in the top
row, and 3 (left) and 4 (right) in the
bottom row.
m
Identifies the AT-MCF2000M
Management Module.
To view the ID and slot numbers of a chassis, refer to
“SYSTEM SHOW CHASSIS” on page 99 or “SYSTEM
SHOW CLUSTER” on page 101.
Privilege Levels
Administrator and read-write.
Description
This command is used to perform a soft reset on a media converter
module or management module in a chassis. The module initializes its
management software. You might reset a module if it is experiencing a
problem.
78
AT-S85 and AT-S97 Management Software User’s Guide
Note
Resetting a media converter module may result in the loss of some
network traffic.
Note
When a management module is reset, it will be unresponsive to
commands for approximately one minute as it initializes the AT-S97
Management Software.
Note
A media converter module will immediately resume forwarding
network traffic through its ports and channels when it is reset. It uses
the default settings for its parameter settings as it initializes its
management software, which takes approximately one minute.
During the initialization process, it will be unresponsive to
management commands. Afterwards, the module will configure its
ports and channels according to the settings in either its own
configuration file or the active master configuration file on the
management module, depending on the configuration overwrite
setting for the slot.
Here are the guidelines to using this command:
ˆ
You can reset only one module at a time.
ˆ
You can use this command to reset a management module or a media
converter module. However, you cannot use this command to reset a
power supply module, a fan module, or the AT-MCF2000S Stacking
Module.
ˆ
If you reset the AT-MCF2000M Management Module, your
management session ends. To continue managing the chassis, start a
new session after the module has initialized its software, which takes
about one minute.
ˆ
Resetting the AT-MCF2000M Management Module does not affect the
network operations of the media converter modules in the chassis.
ˆ
If you reset a media converter module, you can use the SYSTEM
SHOW CLUSTER command or the SYSTEM SHOW CHASSIS
command to determine when a module has finished initializing its
management software.
ˆ
To reset all of the media converter modules in a chassis with just one
command, refer to “SYSTEM RESET CHASSIS” on page 74.
79
Chapter 5: Port and Module Commands
Examples
This command resets the media converter module in slot 2 in the chassis
with the ID number 0:
system reset module id=0/2
This command resets the media converter module in slot 4 in the chassis
with the ID number 2:
system reset module id=2/4
This command resets the AT-MCF2000M Management Module installed:
system reset module id=0/m
This command resets the media converter module in slot 1 in the chassis
with the ID number 5:
system reset module id=5/1
80
AT-S85 and AT-S97 Management Software User’s Guide
SYSTEM SET INTERFACE
Syntax
system set interface id=chassis/slot[/channel]
opmode=link-test|ml|sml
Parameters
id
Specifies a media converter module or a channel. An ID
consists of the following parts:
chassis
Identifies an ID number of a chassis. The range
is 0 to 31. For background information, refer to
“Chassis ID Numbers” on page 25.
slot
Specifies the module you want to configure by
its slot number. Slot numbers are explained in
“Slot Numbers and Letters” on page 26. The
possible values are:
channel
1 or 2
Specifies a slot number of a media
converter module in the
AT-MCF2000 Chassis. The left slot is
1 and the right slot is 2.
1 to 4
Specifies a slot number of a media
converter module in the
AT-MCF2300 Chassis. The slots are
number 1 (left) and 2 (right) in the top
row, and 3 (left) and 4 (right) in the
bottom row.
Specifies the channel you want to configure by
its channel number. You can specify only one
channel. The range is 1 to 12. Channel 1
consists of twisted pair port 1 and fiber topic port
1, channel 2 of twisted pair port 2 and fiber topic
port 2, and so on. You can specify only one
channel at a time. Or, omit this parameter to set
all of the channels on a media converter module
to the same operating mode.
To view the ID and slot numbers of a chassis, refer to
“SYSTEM SHOW CHASSIS” on page 99 or “SYSTEM
SHOW CLUSTER” on page 101. To view the channels,
refer to “SYSTEM SHOW INTERFACE” on page 103.
81
Chapter 5: Port and Module Commands
opmode
Specifies an operating mode for a channel. Available
settings are:
link-test
Specifies the Link Test mode. This is the
default setting.
ml
Specifies the MissingLink™ mode.
sml
Specifies the Smart MissingLink mode.
Privilege Levels
Administrator and read-write.
General Description
This command is used to set the operating modes of the channels on the
media converter modules. Different channels on the same media
converter module can be set to different operating modes. The operating
modes do not interfere with the flow of network traffic through the ports of
a channel. To view a channel’s current operating mode, refer to “SYSTEM
SHOW INTERFACE” on page 103.
Description of the Link Test Mode
Contrary to its name, the Link Test operating mode is not a diagnostic
utility. Rather, it simply reflects the link status of a port on the port’s Link
LED and in the SYSTEM SHOW INTERFACE command. For example,
when a port in a media converter channel running in this mode has a valid
link to a network device, its Link LED is on and its status in the SYSTEM
SHOW INTERFACE command is online. Conversely, when a channel port
operating in this mode does not have a link, its Link LED is off and its
status in the SYSTEM SHOW INTERFACE command is offline.
This mode is typically used when the network devices connected to the
ports of a channel cannot take advantage of the features of the
MissingLink mode, or when you want to use the Link LEDs or the
SYSTEM SHOW INTERFACE command to troubleshoot a network
problem with a channel. This operating mode is also useful after the
installation of a media converter module to verify whether the ports of a
channel have established a link with a network device.
Description of the MissingLink Mode
In the MissingLink mode, the two ports of a channel share their “link”
status with each other so that both ports of a channel and, consequently,
the network devices connected to the ports, are always aware of a change
to the status of the link of the companion port in a channel. When a
channel in the MissingLink mode detects the loss of a link on one of its
ports, it replicates the loss on the companion port in the same channel by
82
AT-S85 and AT-S97 Management Software User’s Guide
disabling the transmitter on the companion port. This notifies the network
device connected to the port of the loss of the link on the other channel
port. Without the MissingLink mode, a network device connected to a
channel port is unaware of a loss of a link on its companion port in the
channel, because its link to the media converter is otherwise unaffected. In
other words, the MissingLink mode does not allow a port in a channel to
form a link with its network device unless the companion port can also
establish a link with its device.
When the link is reestablished on a channel port, the MissingLink mode
automatically reactivates the transmitter on the companion port so that
both network devices can again forward traffic to each other through the
two ports of the media converter channel.
The value to this type of fault notification is that some network devices,
such as managed Fast Ethernet switches, can respond to the loss of a link
on a port by performing a specific action. For example, the network device
might send a trap to a network management station, and so alert the
network administrator of the problem. Or, if the device is running a
spanning tree protocol, it might seek a redundant path to a disconnected
node.
Here is an example of how the MissingLink mode works. Assume that two
ports of a channel are connected to two Fast Ethernet switches, one local
and the other remote. Switch A, the local switch, is connected to the
twisted pair port of the channel, while Switch B, the remote device, is
connected to the fiber optic port. If the link to Switch A is lost on the twisted
pair cable, the media converter disables the transmitter on the fiber optic
port in the same channel to signal Switch B of the loss of the link to Switch
A. This notifies Switch B of the problem so it too, along with Switch A, can
take remedial action, such as activating a redundant path if it is running a
spanning tree protocol or sending an SNMP trap to a management
workstation. Without the MissingLink mode, Switch B would continue to
assume it still has a valid link to the remote device on the other side of the
media converter channel since its link to the port on the channel is still
valid, though no remote traffic is received.
In the example, the initial loss occurred on the twisted pair port. But the
mode operates the same when the initial loss of the link is on the fiber
optic port of a channel. Here, the transmitter on the twisted pair port is
disabled to notify the node connected to that port of the loss of the link on
the fiber optic port.
The states of the ports in a channel running in this mode operate in
tandem. Either both ports have a link or neither port does. This is reflected
on the Link LEDs and in the SYSTEM SHOW INTERFACE command. If
both ports can form a link with their respective network device, then their
Link LEDs will both be on and their status in the SYSTEM SHOW
INTERFACE command will be Online. If one or both ports cannot establish
a link, then their Link LEDs will both be off and their status in the SYSTEM
SHOW INTERFACE command will be Offline.
83
Chapter 5: Port and Module Commands
This operating mode is useful when the network devices connected to the
ports of a channel can react to a loss of a link on a port, such as managed
Fast Ethernet switches running SNMP or a spanning tree protocol.
Conversely, the MissingLink mode is of little value if the network devices
of a channel cannot react to a lost link. In the latter scenario, the Link Test
mode would probably be a better operating mode for a channel during
normal network operations.
Furthermore, Allied Telesis does not recommend using the MissingLink
mode when troubleshooting a network problem that may have its roots
with a link problem. The MissingLink mode does not allow you to use the
port’s Link LEDs or the SYSTEM SHOW INTERFACE command to
diagnose the problem, since neither port will show a link. Rather, the Link
Test and the Smart MissingLink modes are more useful when
troubleshooting a link problem.
Description of the Smart MissingLink Mode
The Smart MissingLink mode, the third operating mode of the media
converter channels, is nearly identical in terms of functionality to the
MissingLink mode. It, too, enables the two ports of a channel to share the
“Link” status of their connections.
The difference is rather than completely shutting off the transmitter of a
port when its companion port in a channel loses its link, this operating
mode pulses the port’s transmitter once a second. This signals the port’s
ability to still establish a link to its network device and that the loss of the
link originated on the companion port in the channel.
The advantage of this operating mode over the MissingLink mode is that
you can use the Link LEDs and the SYSTEM SHOW INTERFACE
command to troubleshoot a link failure with the ports of a channel. A port’s
Link LED starts to flash when its companion port cannot establish a link
with its network device and the port’s status changes to TX SML in the
SYSTEM SHOW INTERFACE command.
Here is an example of how the Smart MissingLink mode works. Assume
that the fiber optic port in a media converter channel lost its link to its
network device while the channel was in the Smart MissingLink operating
mode. The mode would respond by pulsing the transmitter on the twisted
pair port of the channel about once a second. The port’s Link LED would
flash and its status would change to TX SML in the SYSTEM SHOW
INTERFACE command as a signal that the failure originated on the fiber
optic port of the channel. When the connection is reestablished on the
fiber optic port, the twisted pair port resumes normal operations so that the
two ports can again forward traffic to each other.
The operating mode functions the same if the failure starts on the twisted
pair port. Here, the mode pulses the transmitter on the fiber optic port.
84
AT-S85 and AT-S97 Management Software User’s Guide
As with the other two channel operating modes, this mode does not
interfere with the flow of network traffic through the ports of a channel and
so can be used during normal network operations of a media converter
channel. However, you might want to limit its use to diagnosing a link
failure, particularly if the network devices connected to the ports are
managed devices. This is because the pulsing of the transmitter on a port
and the constantly changing status of a link could prove problematic for
some managed devices. For example, the device might send a constant
stream of SNMP traps or, if the device is running a spanning tree protocol,
the protocol may become confused as the status of the device’s link to the
media converter constantly changes.
Mode Select Button
On the front panel of the media converter module is a Mode Select button
that you can use to manually set the operating mode of a channel. Turning
the button up or down toggles through the channels on the module and
pressing it selects a channel’s operating mode. The selected channel is
identified by the CH LEDs on the module and the operating mode by the
LT (Link Test), ML (MissingLink), and SML (Smart MissingLink) LEDs. For
further information, refer to the AT-MCF2000 Multi-channel Media
Converter Series Installation Guide.
A media converter module automatically updates its auxiliary configuration
file in its file system whenever you set a channel’s operating mode with the
Mode Select button. This enables a module in an unmanaged chassis to
retain its channel operating mode settings even when it is moved to
another slot or when a chassis is power cycled.
However, if a chassis has the AT-MCF2000M Management Module or is
part of a stack, the master configuration file on the management module is
not automatically updated when a channel’s operating mode is set with the
Mode Select button. Rather, you must initiate the update with the CONFIG
SAVE command from a local or remote management session. Otherwise,
the settings in the auxiliary configuration file on the module are overwritten
by the master configuration file on the management module the next time
the module or chassis is reset.
For further information on configuration files, refer to Chapter 8,
“Configuration File Commands” on page 145.
Operating Mode Guidelines
The following guidelines apply to using the channel operating modes:
ˆ
The channels on a media converter module can be set to different
operating modes.
ˆ
The operating modes do not block or interfere with the flow of traffic
between the two ports of a channel during normal network operations.
85
Chapter 5: Port and Module Commands
ˆ
The MissingLink mode is intended for situations where the ports of a
channel are connected to managed devices, such as managed Fast
Ethernet switches, that can react to the loss of a link and perform a
specific action, such as send out an SNMP trap or seek a redundant
path using a spanning tree protocol.
ˆ
Allied Telesis does not recommend using the Smart MissingLink mode
on a channel connected to managed devices during normal operations
of the channel. As explained earlier, this mode pulses the transmitter
of a channel port when the link is lost on the companion port, which
might cause problems for a managed device.
ˆ
The Link Test and Smart MissingLink modes are particularly useful
when troubleshooting a link failure on a channel port. These modes
allow you to use the Link LEDs on the ports and the SYSTEM SHOW
INTERFACE command to identify the port in the channel that cannot
establish a link with its network device.
Examples
This command sets all the channels on a media converter module in slot 1
to the Smart MissingLink mode. The chassis has the ID number 0:
system set interface id=0/1 opmode=sml
This command sets channel 6 (twisted pair port 6 and fiber optic port 6) on
a media converter module in slot 2 to the MissingLink mode. The chassis
has the ID number 0:
system set interface id=0/2/6 opmode=ml
This command sets channel 8 (twisted pair port 8 and fiber optic port 8) on
a media converter module in slot 1 to the Link Test operating mode. The
chassis has an ID number 0:
system set interface id=0/1/8 opmode=link-test
86
AT-S85 and AT-S97 Management Software User’s Guide
SYSTEM SET INTERFACE PORTNAME
Syntax
system set interface id=chassis/slot/channel portname=name
Parameters
id
Specifies the ID of the channel you want to assign a name.
The ID consists of the following parts:
chassis
Identifies a chassis ID number. The range is 0 to
31. For background information, refer to
“Chassis ID Numbers” on page 25.
slot
Specifies a slot number of a media converter
module. Slot numbers are explained in “Slot
Numbers and Letters” on page 26. The ranges
are:
channel
portname
1 or 2
Specifies a slot number of a media
converter module in the
AT-MCF2000 Chassis. The left slot is
1 and the right slot is 2.
1 to 4
Specifies a slot number of a media
converter module in the
AT-MCF2300 Chassis. The slots are
number 1 (left) and 2 (right) in the top
row, and 3 (left) and 4 (right) in the
bottom row.
Specifies a channel number on a media
converter module. You can specify only one
channel. The range is 1 to 12. Channel 1
consists of twisted pair port 1 and fiber topic port
1, channel 2 of twisted pair port 2 and fiber topic
port 2, and so on. You can specify only one
channel at a time. Or, omit this parameter to set
all of the channels on a media converter module
to the same operating mode.
Specifies a name of up to 20 alphanumeric characters for a
channel.
Privilege Levels
Administrator and read-write.
87
Chapter 5: Port and Module Commands
Description
This command is used to assign names to the channels on a media
converter module. Naming the channels makes them easier to identify.
Channel names can be viewed with “SYSTEM SHOW INTERFACE” on
page 103.
Examples
This command assigns the name “Region2” to channel 7 (twisted pair port
7 and fiber optic port 7) on a module in slot 2 in a chassis with the ID 0:
system set interface id=0/2/7 portname=Region2
This command assigns the name “NW_traffic” to channel 2 (twisted pair
port 2 and fiber optic port 2) on a module in slot 4 in a chassis with the ID
1:
system set interface id=1/4/2 portname=NW_traffic
88
AT-S85 and AT-S97 Management Software User’s Guide
SYSTEM SET MODULE
Syntax
system set module id=chassis/slot name=name
temperature-threshold=value
Parameters
id
Specifies a module in a chassis. The command can
configure only one module at a time. The ID consists of the
following parts:
chassis
Identifies a chassis ID number. The range is 0 to
31. For background information, refer to
“Chassis ID Numbers” on page 25.
slot
Specifies a slot number or letter. For
background information, refer to “Slot Numbers
and Letters” on page 26. The values and ranges
are:
m
Identifies the AT-MCF2000M
Management Module or the
AT-MCF2000S Stacking Module.
1 or 2
Specifies a slot number of a media
converter module in the
AT-MCF2000 Chassis. The left slot is
1 and the right slot is 2.
1 to 4
Specifies a slot number of a media
converter module in the
AT-MCF2300 Chassis. The slots are
number 1 (left) and 2 (right) in the top
row, and 3 (left) and 4 (right) in the
bottom row.
a or b
Specifies a slot letter of a power
supply or a fan module.
To view the ID and slot numbers of a chassis, refer to
“SYSTEM SHOW CLUSTER” on page 101 or “SYSTEM
SHOW CHASSIS” on page 99. For more information, refer
to “Slot Numbers and Letters” on page 26
name
Assigns a name of up to 20 alphanumeric characters to the
module. Spaces are permitted, but a name with spaces
must be enclosed in double quotes (“ “). To remove the
current value without specifying a new value, enter “none”.
89
Chapter 5: Port and Module Commands
To view the current name of a module, refer to “SYSTEM
SHOW INTERFACE” on page 103, “SYSTEM SHOW
CHASSIS” on page 99 or “SYSTEM SHOW CLUSTER” on
page 101.
temperature-threshold
Specifies a temperature threshold in the range of 0° C to
75° C (32° F to 167° F) for a module. The default value is
60° C. The management module logs an event in the event
log if a module’s temperature exceeds the threshold or if,
after exceeding it, falls below it. Different modules in the
same chassis can have different temperature thresholds.
To view a module’s current temperature threshold value,
refer to “SYSTEM SHOW MODULE” on page 111.
Privilege Levels
Administrator and read-write.
Description
This command is used to assign a name and a temperature threshold to a
module. Names can make identifying the modules easier. Only the
management and media converter modules support names. All of the
modules, including the power supply and fan modules, support
temperature thresholds. To view the module names, refer to “SYSTEM
SHOW INTERFACE” on page 103, “SYSTEM SHOW CHASSIS” on
page 99 or “SYSTEM SHOW CLUSTER” on page 101.
The operating temperature of the modules in a chassis can be monitored
with the temperature threshold parameter. The management module logs
an event in the event log if a module’s temperature exceeds or falls below
the threshold. All of the modules, with the exception of the AT-MCF2000S
Stacking Module, support a temperature threshold. To view a module’s
current temperature threshold value, refer to “SYSTEM SHOW MODULE”
on page 111.
The operating temperatures in a chassis can vary widely depending on the
proximity of the modules to the cooling fans and the areas on the modules
where the temperatures are measured. This should be taken into
consideration when setting a temperature threshold for a module. For a
power supply or fan module, the temperature is measured where the
outside air enters the cooling vents on the module. Consequently, these
modules tend to measure the ambient temperature of the room or wiring
closet where the chassis is installed. In contrast, the temperatures for the
management and media converter modules are measured on the circuit
board away from the cooling vents, and so typically reflect the internal
temperature of the chassis.
90
AT-S85 and AT-S97 Management Software User’s Guide
Examples
This command assigns the name “mm vata” to a management module in a
chassis with the ID 0:
system set module id=0/m name="mm vata"
This command sets the temperature threshold to 55° C for a media
converter module in slot 2 in a chassis with the ID 0:
system set module id=0/2 temperature-threshold=55
This command assigns the name “124 mod-ab” and a temperature
threshold of 70° C to the media converter module in slot 2 of a chassis with
the ID 1:
system set module id=1/2 name="124 mod-ab"
temperature-threshold=70
This command assigns a temperature threshold of 70° C to the power
supply module or fan module in slot A. The chassis has the ID 1:
system set module id=1/a temperature-threshold=70
91
Chapter 5: Port and Module Commands
SYSTEM SET PORT
Syntax
system set port id=chassis/slot[/channel][/port]
port-state=disable|enable auto-neg=disable|enable
speed=10|100|1000 duplex=half|full
crossover=mdi|mdix
ingress-rate-limit=none|value
egress-rate-limit=none|value
Parameters
id
Specifies a port in a channel on a media converter module.
You can configure one port, both ports of a channel, all of
the twisted pair ports on a module, all of the fiber optic
ports, or all of the twisted pair and fiber optic ports. The ID
consists of the following parts:
chassis
Identifies a chassis ID number. The range is 0 to
31. For background information, refer to
“Chassis ID Numbers” on page 25.
slot
Specifies a slot number. For background
information, refer to “Slot Numbers and Letters”
on page 26. The values and ranges are:
channel
92
1 or 2
Specifies a slot number of a media
converter module in the
AT-MCF2000 Chassis. The left slot
is 1 and the right slot is 2.
1 to 4
Specifies a slot number of a media
converter module in the
AT-MCF2300 Chassis. The slots are
number 1 (left) and 2 (right) in the top
row, and 3 (left) and 4 (right) in the
bottom row.
m
Specifies the 10/100/1000Base-T
port on the management module.
Specifies a number of a channel with a port you
want to configure. The range is 1 to 12. Channel
1 consists of twisted pair port 1 and fiber topic
port 1, channel 2 of twisted pair port 2 and fiber
topic port 2, and so on. You can specify only
one channel. To configure all the twisted pair
ports or the fiber optic ports on a module, omit
this parameter.
AT-S85 and AT-S97 Management Software User’s Guide
port
Specifies a port. You can specify only one port.
The possible values are:
a
Specifies the twisted pair port of a
channel.
b
Specifies the fiber optic port of a
channel.
To view the ID and slot numbers of a chassis, refer to
“SYSTEM SHOW CLUSTER” on page 101 or “SYSTEM
SHOW CHASSIS” on page 99. To view the ports of a
channel, refer to “SYSTEM SHOW INTERFACE” on
page 103.
port-state
auto-neg
speed
Enables or disables a port. The available settings are:
enable
Activates the transmitter and receiver on a port.
This is the default setting.
disable
Deactivates the transmitter and receiver on a
port.
Activates and deactivates IEEE 802.3u Auto-Negotiation
and auto-MDI/MDIX on a port. When Auto-Negotiation is
activated, a port’s speed, duplex mode, and wiring
configuration are set automatically. The settings are:
enable
Activates IEEE 802.3u Auto-Negotiation and
auto-MDI/MDIX on the port. This is the default
setting for twisted pair ports. It is also the default
setting for fiber optic ports that support AutoNegotiation, such as 100Base-SX ports. This
setting is not appropriate for fiber optic ports that
do not support Auto-Negotiation, such as
100Base-FX and 1000Base-F ports.
disable
Deactivates IEEE 802.3u Auto-Negotiation and
auto-MDI/MDIX on a port.
Sets the speed of a twisted pair port. The available settings
are:
10
Sets the speed of a port to 10 Mbps.
100
Sets the speed of a port to 100 Mbps.
1000
Sets the speed of a port to 1000 Mbps. This
setting is applicable to the 10/100/1000Base-T
ports on the AT-MCF2032SP Module and on the
10/100/1000Base-T port on the management
93
Chapter 5: Port and Module Commands
module. This setting is not supported on the
twisted pair ports on the AT-MCF2012LC and
AT-MCF2012LC/1 Media Converter Modules.
duplex
crossover
Sets the duplex mode of a port. The available settings are:
full
Sets the duplex mode of the port to full-duplex.
This is the default setting for a fiber optic port
that does not support Auto-Negotiation.
half
Sets the duplex mode of the port to half-duplex.
Sets the wiring configuration of a twisted pair port. AutoNegotiation must be disabled on the port to set this
parameter. The available settings are:
mdi
Sets the wiring configuration to MDI.
mdix
Sets the wiring configuration to MDI-X.
ingress-rate-limit
Defines the maximum number of bits per second a port will
accept from the network device connected to it. The ranges
are 62 to 256000 kbps for the AT-MCF2012LC and
AT-MCF2012LC/1 Media Converter Modules, and 59 to
1000000 kbps for the AT-MCF2032SP Media Converter
Module.
egress-rate-limit
Defines the maximum number of bits per second a port will
transmit to the network device connected to it. The ranges
are 62 to 256000 kbps for the AT-MCF2012LC and
AT-MCF2012LC/1 Media Converter Modules, and 59 to
1000000 kbps for the AT-MCF2032SP Media Converter
Module.
Privilege Levels
Administrator and read-write.
Description
This command is used to configure the following parameter settings on a
twisted pair port or a fiber optic port in a channel on a media converter
module:
94
ˆ
Port status
ˆ
Auto-Negotiation
ˆ
Speed and duplex mode
ˆ
MDI/MDI-X wiring configuration
ˆ
Ingress and egress filtering
AT-S85 and AT-S97 Management Software User’s Guide
This command is also used to set the operating parameters of the 10/100/
1000Base-T Management port on the management module. To view the
current settings of a port, refer to “SYSTEM SHOW INTERFACE” on
page 103.
Note
You should refer to the media converter module’s documentation for
operating specifications before configuring the port parameters. This
is to avoid the possibility of applying an inappropriate setting to a
port. For example, the twisted pair ports on the AT-MCF2012LC
media converter module support speeds of 10 and 100 Mbps, but
not 1000 Mbps.
The PORT-STATE parameter is used to enable and disable ports. A
disabled port does not forward ingress or egress packet traffic. You might
disable a port to secure it from unauthorized use or when troubleshooting
a network problem. The default setting for a port is enabled.
The AUTO-NEG parameter is used to enable and disable IEEE 802.3u
Auto-Negotiation and auto-MDI/MDIX on a twisted pair port in a media
converter channel. (Auto-Negotiation is not applicable to the fiber optic
ports on the AT-MCF2012LC and AT-MCF2012LC/1 Media Converter
Modules.) When Auto-Negotiation is enabled, the speed, duplex mode,
and MDI/MDIX settings of a port are set automatically. When AutoNegotiation is disabled, the port’s operating parameters can be set
manually.
Auto-Negotiation should only be used on a twisted pair port when the
device connected to the port is also using Auto-Negotiation. Otherwise, a
duplex mode mismatch may occur, resulting in reduced network
performance. A port using Auto-Negotiation defaults to half-duplex if it
detects that the port on the other network device is not using AutoNegotiation. The result would be a duplex mode mismatch if the port on
the other network device is operating at a fixed duplex mode of full-duplex.
To avoid this issue, you should disable Auto-Negotiation on a media
converter port and set the speed and duplex mode manually when the
network device connected to the port can only operate in full-duplex mode.
Alternatively, you can reconfigure the port on the network device to AutoNegotiation or, if it does not support that feature, to half-duplex mode.
The SPEED, DUPLEX, and CROSSOVER parameters are used to set the
speed, duplex mode, and MDI/MDIX settings, respectively, on a twisted
pair port when Auto-Negotiation is disabled.
You cannot set the speed of the fiber optic ports on the AT-MCF2012LC
and AT-MCF2012LC/1 Media Converter Modules because they have a
fixed speed of 100 Mbps. Additionally, you cannot set the speed of an SFP
module in the AT-MCF2032SP Media Converter Module. The speed of an
SFP module is detected automatically by the media converter module.
95
Chapter 5: Port and Module Commands
The DUPLEX parameter can also be used to set the duplex mode on a
fiber optic port in a media converter channel.
For best network performance, all the elements of a media converter
channel, meaning the two ports of a channel and the two network devices
connected to the ports, should be using the same duplex mode. A media
converter channel may have to discard packets if its two ports are
operating in different modes, one half-duplex and the other full-duplex.
This could result in a decrease of network performance if the network
devices have to frequently retransmit packets.
For example, if the network device connected to the twisted pair port of a
media converter channel is only capable of half-duplex mode, then both
ports of the channel and the network device connected to the fiber optic
port in the channel should be configured to operate in half-duplex mode as
well.
Also featured on the twisted pair ports of a media converter module is
auto-MDI/MDI-X, which automatically adjusts the wiring configuration of a
twisted pair port to either MDI or MDI-X, depending on the wiring
configuration of the end node. This feature allows the use of a straightthrough twisted pair cable regardless of the wiring configuration of the port
on the network device.
The auto-MDI/MDI-X feature is only available when a twisted pair port is
using Auto-Negotiation, the default setting. Disabling Auto-Negotiation
and manually configuring a port’s speed and duplex mode also disables
this feature. The wiring configuration of a port defaults to the MDI-X
setting. Disabling Auto-Negotiation may require the manual configuration
of the MDI/MDI-X setting on a port or the use a crossover cable,
depending on the wiring configuration of the network device connected to
the port on the module.
The INGRESS-RATE-LIMIT and EGRESS-RATE-LIMIT parameters
control the flow of network traffic to and from a port in a channel to its
network device. The rate limits, which are in kilobits and megabits per
second, can be applied separately to the two ports of a channel. The rate
limits can be used for storm prevention and to protect against the
formation of bottlenecks in a network topology,
The INGRESS-RATE-LIMIT feature controls the number of bits per
second a port will accept from the device connected to it. The port
discards frames after the limit is exceeded. For example, an ingress rate
limit of 128 limits a port to no more than 128 kilobits per second in traffic
flow from its network device.
The EGRESS-RATE-LIMIT controls the number of bits per second a port
will transmit to the network device connected to it.
The 10/100/100Base-T Management port on the management module
does not support ingress or egress rate limits.
96
AT-S85 and AT-S97 Management Software User’s Guide
Examples
This command disables Auto-Negotiation of the twisted pair port in
channel 5 of a media converter module and sets the port’s speed and
duplex mode to 100 Mbps, half-duplex. The module is in slot 2 of a chassis
with the ID number of 1. Call-outs in the example identify the parts of the
ID number:
system set port id=0/2/5/a auto-neg=disable speed=100 duplex=half
Chassis
Slot
Port
Channel
This command enables twisted port 5. The module is in slot 1 of a chassis
with an ID number of 3:
system set port id=3/1/5/a port-state=enable
This command disables Auto-Negotiation of the twisted pair port in
channel 2 of a media converter module and sets the port’s speed and
duplex mode to 10 Mbps, full-duplex, and the MDI/MDI-X setting to MDI.
The module is in slot 1 of a chassis with an ID number of 1:
system set port id=1/1/2/a auto-neg=disable speed=10
duplex=full crossover=mdi
This command activates Auto-Negotiation on the twisted pair port in
channel 4. The module is in slot 1 of a chassis with an ID of 2:
system set port id=2/1/4/a auto-neg=enable
This command sets the duplex mode to half-duplex for the fiber optic port
in channel 11 on a module in slot 2 of a chassis with an ID of 2:
system set port id=2/2/11/b duplex=half
This command disables the fiber optic port in channel 6 of the module in
slot 1. The chassis has the ID number 3:
system set port id=3/1/6/b port-state=disable
The previous examples illustrate how to configure a single port on a media
converter module. By omitting the PORT PAIR parameter, you can
configure all of the ports of the same type (that is, twisted pair or fiber optic
ports) with just one command. This is illustrated in the following two
examples.
97
Chapter 5: Port and Module Commands
This command disables all of the twisted pair ports in the media converter
module in slot 1. The chassis has the ID number of 1:
system set port id=1/1/a port-state=disable
This command sets the duplex mode to half-duplex for all the fiber optic
ports in the media converter module in slot 2. The chassis has the ID
number of 1:
system set port id=1/2/b duplex=half
The SYSTEM SET PORT command can also be used to configure the 10/
100/1000Base-T Management port on the management module. This
example disables Auto-Negotiation on the port and sets it to 100 Mbps,
full-duplex. The chassis has the ID number of 0:
system set port id=0/m auto-neg=disable speed=100
duplex=full
98
AT-S85 and AT-S97 Management Software User’s Guide
SYSTEM SHOW CHASSIS
Syntax
system show chassis id=chassis
Parameters
chassis
Identifies a chassis ID number. The range is 0 to
31. For background information, refer to
“Chassis ID Numbers” on page 25.
To view the ID number of a unit, use the SYSTEM SHOW
CLUSTER command. For instructions, refer to “SYSTEM
SHOW CLUSTER” on page 101.
Privilege Levels
Administrator, read-write and read-only.
Description
This command is used to display the model names and slot assignments
of the management module and the media converter modules in a chassis.
It is also used to view a chassis’ module name and MAC address.
You can view just one chassis at a time with this command. To view all of
the chassis of a stack with one command, use the SYSTEM SHOW
CLUSTER command, as explained in “SYSTEM SHOW CLUSTER” on
page 101.
An example of the information is shown in Figure 12.
Chassis
Chassis
Chassis
MAC
Master
ID
Name
Type
Address
Chassis
-----------------------------------------------------------------0
AT-MCF2000
11:22:33:44:55:55
Yes
Slot ID
Module Name
Module Type
Cfg Overwrite Software Version
--------------------------------------------------------------------M
AT-MCF2000M
v3.0.0
1
AT-MCF2012LC
Disable
v3.0.0
2
AT-MCF2012LC
Disable
v3.0.0
A
AT-MCF2KFAN
B
AT-MCF2000AC
-
Figure 12. SYSTEM SHOW CHASSIS Command
99
Chapter 5: Port and Module Commands
The fields are defined here:
Table 6. SYSTEM SHOW CHASSIS Command
Parameter
Description
Chassis ID
Displays the ID number of a chassis. The range is 0 to 31. For
background information, refer to “Chassis ID Numbers” on
page 25.
Chassis Name
Displays the name of a chassis. To set a chassis name, refer to
“SYSTEM SET CHASSIS” on page 59.
Chassis Type
Displays the model name of a chassis.
MAC Address
Displays the MAC address of a chassis. The AT-MCF2000M
Management Module uses its chassis’ MAC address as its own
address when communicating with a network.
Master Chassis
Indicates whether the chassis contains the AT-MCF2000M
Management Module or the AT-MCF2000S Stacking Module.
A chassis with the management card will have a status of Yes,
and a unit with the stacking module will have a status of No.
Slot ID
Lists the slots in the chassis. Slots that are empty are not
included. The slots are:
ˆ
M: Indicates the management slot containing the
AT-MCF2000M Management Module.
ˆ
number: Indicates a slot for a media converter module
number (for example, 1, 2, etc.). Empty slots are not
included in the tables.
This command does not display the AT-MCF2000S Stacking
Module.
Module Name
Displays the names of the modules. To assign names, refer to
“SYSTEM SET MODULE” on page 89.
Module Type
Displays the model names of the modules.
Software Version
Displays the version numbers of the AT-S85 and AT-S97
Management Software programs on the modules.
Example
The following command displays information about a chassis with the ID
number 0:
system show chassis id=0
100
AT-S85 and AT-S97 Management Software User’s Guide
SYSTEM SHOW CLUSTER
Syntax
system show cluster
Parameters
None.
Privilege Levels
Administrator, read-write and read-only.
Description
This command is used to display the model names and slot assignments
of the management and media converter modules in a chassis or stack, as
well as the chassis’ module name and MAC address. This command does
not display any information about the stacking, power supply, or fan
modules.
This command is similar to the SYSTEM SHOW CHASSIS command in
that both commands display the same information about a chassis. Where
they differ is that the SYSTEM SHOW COMMAND can display only one
chassis at a time and requires a chassis ID number. In contrast, this
command displays all of the chassis of a stack and does not require an ID
number.
The SYSTEM SHOW CLUSTER command is typically used to view the
basic information above on a single chassis that is not part of a stack or for
all of the chassis of a stack. The SYSTEM SHOW CHASSIS command is
intended for situations where there is a stack and, rather than viewing all of
the devices, you want to focus on just one of the units.
Figure 13 on page 102 illustrates this command on a stack of three
chassis. For an explanation of the information, refer to “SYSTEM SHOW
CHASSIS” on page 99.
101
Chapter 5: Port and Module Commands
Chassis
Chassis
Chassis
MAC
Master
ID
Name
Type
Address
Chassis
----------------------------------------------------------------0
AQ Traffic AT-MCF2000
11:22:33:44:55:55
Yes
AT-MCF2000
Slot ID
Module Name
Module Type
Cfg Overwrite Software Version
---------------------------------------------------------------------M
AT-MCF2000M
v3.0.0
1
Reg 1 traf
AT-MCF2012LC
Enable
v3.0.0
2
Reg 2 traf
AT-MCF2012LC/1 Enable
v3.0.0
1
ACT Traffic
11:22:33:44:22:22
No
AT-MCF2000
Slot ID
Module Name
Module Type
Cfg Overwrite Software Version
---------------------------------------------------------------------1
Reg 7 traf
AT-MCF2012LC
Disable
v3.0.0
2
Reg 12 traf
AT-MCF2012LC
Disable
v3.0.0
2
UJ Traffic
11:22:33:44:66:77
No
AT-MCF2300
Slot ID
Module Name
Module Type
Cfg Overwrite Software Version
---------------------------------------------------------------------1
District 1
AT-MCF2012LC
Enable
v3.0.0
2
District 2
AT-MCF2012LC
Enable
v3.0.0
3
District 3
AT-MCF2012LC
Enable
v3.0.0
4
District 4
AT-MCF2012LC/1 Enable
v3.0.0
Figure 13. SYSTEM SHOW CLUSTER Command
Example
system show cluster
102
AT-S85 and AT-S97 Management Software User’s Guide
SYSTEM SHOW INTERFACE
Syntax - Chassis Only
system show interface id=chassis
Syntax - Chassis and Slot
system show interface id=chassis/slot
Syntax - Chassis, Slot and Channel
system show interface id=chassis/slot/channel
Parameters
id
Specifies a chassis, slot or channel. The command can
display only one device at a time. The ID consists of the
following parts:
chassis
Identifies the ID number of the chassis. The
range is chassis ID number depends on which
module is installed in the management slot of
the chassis. When a management module is
installed in this slot, the chassis ID number is
either 0 or 31. When a stacking module is
installed in this slot, the range of the chassis ID
is from 1 to 30.
slot
Specifies a slot number of a media converter
module with a port to be configured. The
possible values are:
channel
1 or 2
Specifies a slot number of a media
converter module in the
AT-MCF2000 Chassis. The left slot is
1 and the right slot is 2.
1 to 4
Specifies a slot number of a media
converter module in the
AT-MCF2300 Chassis. The slots are
number 1 (left) and 2 (right) in the top
row, and 3 (left) and 4 (right) in the
bottom row.
Specifies a number of a channel on a media
converter module. You can specify only one
channel at a time. The range is 1 to 12. Channel
1 consists of twisted pair port 1 and fiber topic
103
Chapter 5: Port and Module Commands
port 1, channel 2 of twisted pair port 2 and fiber
topic port 2, and so on.
To view the ID and slot numbers of a chassis, refer to
“SYSTEM SHOW CLUSTER” on page 101 or “SYSTEM
SHOW CHASSIS” on page 99.
Privilege Levels
Administrator, read-write, and read-only.
General Description
This command can display a variety of status information about a media
converter chassis and the media converter modules. You can limit the
information to just the model names of the media converter modules in a
chassis or view more detailed information about the devices, such as the
current operating parameters of the two ports of a media converter
channel.
Note
To view the parameter settings of the 10/100/1000Base-T port on
the AT-MCF2000M Management Module, use the SYSTEM SHOW
MODULE command. For information, refer to “SYSTEM SHOW
MODULE” on page 111.)
Description of the Chassis Only Command
Specifying just a chassis ID number in the command displays the names
of the media converter models in a chassis and their respective slot
numbers. This is useful in determining the types of media converter
modules in a chassis. An example of the information is shown in
Figure 14.
Interface 0 Information:
Chassis ID
Slot ID
Module Name
Module Type
---------------------------------------------------1
1
Traffic 12
AT-MCF2012LC
1
2
Traffic 7
AT-MCF2012LC
Figure 14. SYSTEM SHOW INTERFACE Command - Chassis ID Only
104
AT-S85 and AT-S97 Management Software User’s Guide
The table does not include empty media converter slots. The columns are
defined here:
Table 7. SYSTEM SHOW INTERFACE Command - Chassis ID Only
Column
Description
Chassis ID
Displays the ID number of the selected
chassis.
Slot ID
Displays the slot numbers in the chassis
Module Name
Displays the names of the modules.
Module Type
Displays the model names of the
modules.
Description of the Chassis and Slot Command
To view the current status of the channel ports on a media converter
module, including the status of the links between the channel ports and the
network devices, specify in the command both a chassis ID number and
the slot number of the module. Figure 15 is an example.
Interface 0/2 Information:
Chassis ID .......... 0
Slot ID ............. 2
Module Name ......... User Module
Module Type ......... AT-MCF2012LC
Port ID
Port Name
Copper
Fiber
OpMode
-------------------------------------------------------------1
Online/100
Online/100
Link Test
2
Online/100
Online/100
Link Test
3
Online/100
Online/100
Link Test
4
Online/100
Online/100
Link Test
5
Online/100
Online/100
Link Test
Figure 15. Chassis ID and Slot Number
The information in the table is arranged according to the media converter
channels in a module. The “Port ID” column lists the channels and the
“Port Name” column lists the channel names. Neither can be changed. For
example, “Port ID 1” refers to channel 1 which, on the AT-MCF2012LC
and AT-MCF2012LC/1 Modules, consists of twisted pair port 1 and fiber
optic port 1, “Port ID 2” refers to channel 2 with twisted pair port 2 and fiber
optic port 1, and so on.
105
Chapter 5: Port and Module Commands
The columns are defined here:
Table 8. SYSTEM SHOW INTERFACE Command - Chassis ID and Slot
Number
Column
Description
Port ID
Displays the channel numbers.
Port Name
Displays the channel names.
Copper - Fiber
Displays the current states of the twisted
pair ports and the fiber optic ports of the
channels
OpMode
Displays the current operating modes of
the channels. For information, refer to
“SYSTEM SET INTERFACE” on page 81.
The meanings of the states of the two ports in a channel can differ
depending on a channel’s operating mode of Link Test, MissingLink, or
Smart MissingLink. The easiest way to decipher the states is to consider a
channel’s two ports as a unit. Table 9 lists the possible combinations of
port states when a channel is in the Link Test mode.
Table 9. Port Status in the Link Test Mode
Channel Port
106
Status
Copper
Offline
Fiber
Offline
Copper
Online
Fiber
Online
Copper
Online
Fiber
Offline
Copper
Offline
Fiber
Online
Description
Neither port in the channel has
established a link with a network
device.
Both ports in the channel have
established a link with a network
device.
The twisted pair port in the channel has
established a link with a network
device, but the fiber optic port has not
established a link.
The fiber optic port of the channel has
established a link with a network
device, but the twisted pair port has not
established a link.
AT-S85 and AT-S97 Management Software User’s Guide
Table 10 lists the possible combinations of the port states for a channel in
the Missing Link mode.
Table 10. Port Status in the Missing Link Mode
Channel Port
Status
Copper
Offline
Fiber
Offline
Copper
Online
Fiber
Online
Description
One or both ports in the channel
cannot establish a link with a network
device.
Both ports in the channel have
established a link with a network
device.
The states for the ports of a channel in the Smart MissingLink mode are
explained in Table 11.
Table 11. Port Status in the Smart Missing Link Mode
Channel Port
Status
Copper
Offline
Fiber
Offline
Copper
Online
Fiber
Online
Copper
TX SML
Fiber
Offline
Copper
Offline
Fiber
TX SML
Twisted Pair
Port
TX or RX
SML
Fiber Optic Port TX or RX
SML
Description
Neither port in the channel has
established a link with a network
device.
Both ports in the channel have
established a link with a network
device.
The twisted pair port of the channel
can establish a link with its network
device, but the fiber optic port is unable
to establish a link with its remote
device.
The fiber optic port of a channel can
establish a link with its network device,
but the twisted pair port is unable to
establish a link with its local device.
Both ports in the channel can establish
a link to a network device, but one of
the ports is connected to another
media converter that also supports the
Smart MissingLink feature, forming a
chain of converters. A link has been
lost on one of the ports in the chain,
causing a ripple affect through the
chain of converters.
107
Chapter 5: Port and Module Commands
Description of the Chassis, Slot, and Channel Command
To view the operating parameters of the channel’s two ports, including the
speeds and duplex modes, specify a channel number in the command.
You can view only one channel at a time. Figure 16 is an example of the
information.
Interface 0/2/7 Information
Chassis ID ............... 0
Slot ID .................. 2
Module Name .............. User Module
Module Type .............. AT-MCF2012LC
Port Name ................ User Port
OpMode ................... Link Test
Port Copper Link
Port State .......... Enabled
Link Status ......... Online
Auto Negotiation .... Enabled
Speed ............... 100 Mbps
Duplex .............. Full
MDI Crossover ....... MDI
Ingress Rate Limit .. No Limit
Egress Rate Limit ... No Limit
Maximum Frame Size .. 1632 bytes
Port Fiber Link ....
Port State .......... Enabled
Link Status ......... Online
Speed ............... 100 Mbps
Duplex .............. Full
Ingress Rate Limit .. No Limit
Egress Rate Limit ... No Limit
Maximum Frame Size .. 1632 bytes
Figure 16. SYSTEM SHOW INTERFACE Command - Chassis ID, Slot
Number and Channel Number
The fields are defined here.
Table 12. SYSTEM SHOW INTERFACE Command - Chassis ID, Slot Number and Channel
Number
Parameter
108
Description
Interface Information
Displays the identity number of a channel. The information is
given as chassis number, slot number, and channel number.
Chassis ID
Displays the ID number of a chassis.
Slot ID
Displays the slot number of a media converter module.
Module Name
Displays the name of a module. To assign a name, refer to
“SYSTEM SET MODULE” on page 89.
AT-S85 and AT-S97 Management Software User’s Guide
Table 12. SYSTEM SHOW INTERFACE Command - Chassis ID, Slot Number and Channel
Number
Parameter
Description
Module Type
Displays the model name of a module.
Port Name
Displays a channel’s name.
OpMode
Displays the operating mode of a channel. The possible
operating modes are MissingLink, Smart MissingLink, and Link
Test. The operating modes are described in “SYSTEM SET
INTERFACE” on page 81.
Port State
Displays the status of a port. The possible states are:
Enabled - A port is able to forward network traffic.
Disabled - A port was disabled with SYSTEM SET PORT
command to prevent it from forwarding network traffic. For
information, refer to “SYSTEM SET PORT” on page 92.
Link Status
Displays the status of the link of a port to its network device.
The possible states are described in Table 9, “Port Status in
the Link Test Mode” on page 106, Table 10, “Port Status in the
Missing Link Mode” on page 107, and Table 11, “Port Status in
the Smart Missing Link Mode” on page 107.
Auto Negotiation
Displays the status of Auto-Negotiation on a twisted pair port.
The status of Enabled is an indication that the twisted pair
port’s speed, duplex mode, and MDI/MDI-X wiring
configuration are set automatically with Auto-Negotiation and
the auto-MDI/MDI-X feature. A status of Disabled means the
port’s speed, duplex mode, and MDI/MDI-X wiring
configuration are set manually.
Speed
Displays the speed of a port when the parameter is set
manually. This parameter does not reflect the current speed of
a port whose speed is set with Auto-Negotiation.
Duplex
Displays the duplex mode of a port when the parameter is set
manually. This parameter does not reflect the current duplex
mode of a port whose duplex mode is set with AutoNegotiation.
MDI Crossover
Displays the wiring configuration of a twisted pair port.
Ingress and Egress Rate
Limits
Displays the packet rate limits of a port. Packets exceeding the
limit are discarded by a port. Packet rate limiting is described in
“SYSTEM SET PORT” on page 92.
109
Chapter 5: Port and Module Commands
Table 12. SYSTEM SHOW INTERFACE Command - Chassis ID, Slot Number and Channel
Number
Parameter
Maximum Frame Size
Description
Displays the maximum frame size of a port. This value cannot
be changed and is the same for all of the ports on a module.
The maximum frame sizes are 1632 bytes for the
AT-MCF2012LC and AT-MCF2012LC/1 Media Converter
Modules and 10240 bytes for the AT-MCF2032SP Media
Converter Module.
To configure the channels and ports of a media converter module, refer to
“SYSTEM SET INTERFACE” on page 81 and “SYSTEM SET PORT” on
page 92.
Examples
This command displays a list of the media converter modules in a chassis
with the ID number 0:
system show interface id=0
This command displays the status of all the channel ports on a media
converter module in slot 2 of a chassis with the ID number 1:
system show interface id=1/2
This command displays the parameter settings for the two ports of
channel 11 of a media converter module in slot 1 of a chassis with the ID
number 1:
system show interface id=1/1/11
110
AT-S85 and AT-S97 Management Software User’s Guide
SYSTEM SHOW MODULE
Syntax
system show module id=chassis/slot
Parameters
id
Identifies the ID number of a module. You can specify only
one module at a time. The ID number consists of the
following parts:
chassis
Specifies a chassis ID number. The range is 0 to
31. For background information, refer to
“Chassis ID Numbers” on page 25.
slot
Specifies a slot number or letter. The possible
values are:
m
Specifies the management module
slot. This slot is used for the
management module or the stacking
module.
a or b
Specifies a slot letter of a power
supply or fan module. The left slot is
A and the right slot is B.
1 or 2
Specifies a slot number of a media
converter module in the
AT-MCF2000 Chassis. The left slot is
1 and the right slot is 2.
1 to 4
Specifies a slot number of a media
converter module in the
AT-MCF2300 Chassis. The slots are
number 1 (left) and 2 (right) in the top
row, and 3 (left) and 4 (right) in the
bottom row.
To view the ID number and the slot numbers of a chassis,
refer to “SYSTEM SHOW CLUSTER” on page 101 or
“SYSTEM SHOW CHASSIS” on page 99.
Privilege Levels
Administrator, read-write, and read-only.
111
Chapter 5: Port and Module Commands
Description
This command is used to display status information about the media
converter, power supply, fan, and management modules in a chassis. The
information varies depending on the module. Figure 17 is an example of
the information for the AT-MCF2000AC Power Supply Module or the
AT-MCF2KFAN Fan Module.
RPSA Information:
Module Name ................
Module Type ................
Power OK ...................
Module Present .............
3.3V .......................
12.0V ......................
Temperature ................
Temperature Threshold ......
Fan A Speed ................
Fan B Speed ................
AT-MCF2000AC
Yes
Present
Good = 3.415V
Good = 12.125V
25.821 C
60 C
7105 RPM
7033 RPM
Figure 17. SYSTEM SHOW MODULE Command for a Power Supply or
Fan Module
The acronym “RPS” for “Redundant Power Supply” in the top line should
be ignored. It is a misnomer for a fan module as well as for a power supply
module in a chassis with one power supply. The letter following “RPS” is
the chassis slot location of the power supply or fan module.
Figure 18 illustrates the information for the management module.
112
AT-S85 and AT-S97 Management Software User’s Guide
CPU Information:
Name .......................
Module Type ................ AT-MCF2000M
Module Status .............. Active
Module Present ............. Present
1.2V ....................... Good = 1.212V
1.8V ....................... Good = 1.818V
2.5V ....................... Good = 2.535
3.3V ....................... Good = 3.336V
12.0V ...................... Good = 12.187
Temperature ................ 29.2500 C
Temperature Threshold ...... 60 C
Management Port:
Link State ........... Up
Auto Negotiation...... Enabled
Speed ................ 100 Mbps
Duplex ............... Full
MDI Crossover ........ MDI
Stacking Port:
Link State ............ Up
Figure 18. SYSTEM SHOW MODULE Command for the Management
Module
The information for a media converter module is shown in Figure 19.
CPU Information:
Name .......................
Module Type ................
Module Status ..............
Module Present .............
1.2V .......................
1.8V .......................
2.5V .......................
3.3V .......................
12.0V ......................
Temperature ................
Temperature Threshold ......
AT-MCF2012LC
Active
Present
Good = 1.198
Good = 1.804V
Good = 2.509
Good = 3.302V
Good = 12.6224
38.15 C
60 C
Figure 19. SYSTEM SHOW MODULE Command for a Media Converter
Module
113
Chapter 5: Port and Module Commands
The fields are defined here:
Table 13. SYSTEM SHOW MODULE Command
Parameter
Description
Module Name
Displays the name of the module. Refer to “SYSTEM SET
MODULE” on page 89 for instructions on how to assign a
name to a module.
Module Type
Displays the model name.
Power OK
Displays the status of the input power of a power supply
module or a fan module A status of Yes signifies the input
power is within the module’s operating range. A status of No
signals that the input power is less or greater than the
permitted range.
Voltages
Displays the operating output voltages for the AT-MCF2000AC
Power Supply Module and input voltages for all other modules.
Temperature
Displays the current temperature of a module. On the
AT-MCF2000AC Power Supply Module and the
AT-MCF2KFAN Fan Module the temperature is measured at
the point where the outside air enters the chassis from the
cooling vents. The temperature for all the other modules is
measured on the circuit boards.
Temperature Threshold
Displays the temperature threshold of a module. The
management module logs an event in the event log if the
threshold is exceeded, to warn of possible excessive
temperature in the wiring closet or chassis. Refer to “SYSTEM
SET MODULE” on page 89 for instructions on setting a
module’s temperature threshold.
Management Port
Displays the status of the link of the 10/100/1000Base-T
Management port on the AT-MCF2000M Management Module
and, if the port has a link to a network device, the current
settings. Refer to “SYSTEM SET PORT” on page 92 for
instructions on setting the parameters of the port.
Stacking Port
Displays the status of the Stack port connection on the
AT-MCF2000M Management Module. A status of Up indicates
the port has established a link with a Stack port in another
chassis.
Examples
This command displays information about the AT-MCF2000M
Management Module in a chassis with an ID number of 0:
system show module id=0/m
114
AT-S85 and AT-S97 Management Software User’s Guide
This command displays information about the media converter module in
slot 2 in a chassis with an ID number of 0:
system show module id=0/2
115
Chapter 5: Port and Module Commands
116
Chapter 6
Network Time Protocol Commands
This chapter contains the following sections:
ˆ
“Overview” on page 118
ˆ
“NTP DISABLE” on page 120
ˆ
“NTP ENABLE” on page 121
ˆ
“NTP SET” on page 122
ˆ
“NTP SHOW” on page 123
Note
Remember to save your parameter changes in the active master
configuration file with the CONFIG SAVE command. For information,
refer to “Saving Your Configuration Changes” on page 23 or Chapter
8, “Configuration File Commands” on page 145.
117
Chapter 6: Network Time Protocol Commands
Overview
The AT-S97 Management Software has a Network Time Protocol (NTP)
client so that it can set its internal clock and calender from an NTP server
on your network or the Internet. It adds the date and time to the events
stored in the event log and to SNMP traps.
The commands described in this chapter control the NTP client. The client
is activated and deactivated with the NTP ENABLE command and the
NTP DISABLE command, and the IP address of the NTP server is
specified with the NTP SET command.
To manually set the date and time, refer to “SYSTEM SET CLOCK” on
page 60.
NTP Client
Guidelines
Command
Summary
The guidelines to using the NTP client are:
ˆ
The AT-MCF2000M Management Module must have an IP
configuration, as explained in Chapter 3, “IP Configuration
Commands” on page 47.
ˆ
The 10/100/1000Base-T Management port on the management
module must be connected to a device on your network, such as a
Fast Ethernet or Gigabit Ethernet switch. The module communicates
with the NTP server through this port.
ˆ
The NTP server must be a member of the same network as the
management module or have access to it through Layer 3 routing
devices.
ˆ
If the management module and the NTP server are on different
networks, the IP configuration on the module must include a default
gateway address specifying the IP address of the routing interface of
the first hop to reaching the remote server. For instructions, refer to
Chapter 3, “IP Configuration Commands” on page 47.
ˆ
Before you enable the NTP server with the NTP ENABLE command,
connect the chassis to an NTP server.
Table 14 summarizes the NTP client commands.
Table 14. NTP Client Commands
Command
118
Description
NTP DISABLE on page 120
Deactivates the NTP client.
NTP ENABLE on page 121
Activates the NTP client.
AT-S85 and AT-S97 Management Software User’s Guide
Table 14. NTP Client Commands (Continued)
Command
Description
NTP SET on page 122
Specifies the IP address of the
NTP server on the network or the
Internet.
NTP SHOW on page 123
Displays the current settings of the
NTP client.
119
Chapter 6: Network Time Protocol Commands
NTP DISABLE
Syntax
ntp disable
Parameters
None.
Privilege Levels
Administrator and read-write.
Description
This command is used to disable the NTP client on the management
module. This is the client’s default setting.
Example
ntp disable
120
AT-S85 and AT-S97 Management Software User’s Guide
NTP ENABLE
Syntax
ntp enable
Parameters
None.
Privilege Levels
Administrator and read-write.
Description
This command is used to activate the NTP client on the management
module. When the client is activated, it immediately begins polling for the
NTP server, up to fifteen times over twenty seconds. The default setting
for the client is disabled.
To set the IP address of the NTP server, use “NTP SET” on page 122.
Note
Review “NTP Client Guidelines” on page 118 before activating the
client.
Note
Your management session is suspended while the NTP client polls
for the server.
Example
ntp enable
121
Chapter 6: Network Time Protocol Commands
NTP SET
Syntax
ntp set server=ipaddress utcoffset=integer
Parameters
server
Specifies an IP address of an NTP server. To delete the
current value without specifying a new value, enter
“0.0.0.0”.
utcoffset
Specifies a time difference, in hours, between the Universal
Time Coordinated (UTC) and the local time zone. The
range is from -12 to +12 hours. The default is 0 hours.
Privilege Levels
Administrator and read-write.
Description
This command is used to specify an IP address of a NTP server on your
network or the Internet, and a time offset between the UTC and the local
time zone.
Examples
This command specifies the IP address of the NTP server as
149.122.55.77:
ntp set server=149.122.55.77
This command specifies the IP address of the NTP server as
149.122.55.79 and a UTC offset of 3 hours:
ntp set server=149.122.55.79 utcoffset=3
This command specifies the IP address of the NTP server as
149.122.55.81 and the UTC offset of -6 hours:
ntp set server=149.122.55.81 utcoffset=-6
122
AT-S85 and AT-S97 Management Software User’s Guide
NTP SHOW
Syntax
ntp show
Parameters
None.
Privilege Levels
Administrator, read-write, and read-only.
Description
This command is used to display information about the NTP client on the
management module. The information includes the status of the client, the
IP address of the NTP server, and the UTC offset. An example is shown in
Figure 20.
NTP Information:
Status ............. Disable
Server ............. 0.0.0.0
UTC Offset .......... 0
Figure 20. NTP SHOW Command
Example
ntp show
123
Chapter 6: Network Time Protocol Commands
124
Chapter 7
Event Log and Syslog Client Commands
This chapter contains the following sections:
ˆ
“Overview” on page 126
ˆ
“LOGGING CLEAR EVENTLOG” on page 128
ˆ
“LOGGING DISABLE EVENTLOG” on page 129
ˆ
“LOGGING DISABLE SYSLOG” on page 130
ˆ
“LOGGING ENABLE EVENTLOG” on page 131
ˆ
“LOGGING ENABLE SYSLOG” on page 132
ˆ
“LOGGING SET EVENTLOG” on page 133
ˆ
“LOGGING SET SYSLOG” on page 135
ˆ
“LOGGING SHOW” on page 136
ˆ
“LOGGING SHOW EVENTLOG” on page 138
Note
Remember to save your parameter changes in the active master
configuration file with the CONFIG SAVE command. For information,
refer to “Saving Your Configuration Changes” on page 23 or Chapter
8, “Configuration File Commands” on page 145.
125
Chapter 7: Event Log and Syslog Client Commands
Overview
The management, media converter, power supply, and fan modules
generate event messages with vital information about system activity. If a
network problem occurs, the messages can help you determine the
sequence of events that led to the problem as well as identify and resolve
it. An event message contains the following information:
ˆ
The time and date of the event
ˆ
The severity level of the event
ˆ
A description of the event
The events are stored in the event log, an area of non-volatile memory
separate from the file system where the messages are retained even
when the chassis is powered off. The log’s maximum capacity is 1,024
events. When the log reaches maximum capacity, the module deletes the
oldest events as it adds new events.
The event log is controlled and viewed with the LOGGING commands.
The LOGGING ENABLE command activates the log, the default setting,
and the LOGGING DISABLE command deactivates the log, stopping the
log from storing any further event messages. The LOGGING SHOW
command displays the status of the log and the events messages, and the
LOGGING CLEAR command deletes all the events messages from the
log.
The management module also has a syslog client for sending the event
messages to a syslog server on your network. A server can act as the
central storage device for the event messages from many different
devices on your network. To use the syslog client, you must specify the IP
address of the syslog server on the network with the LOGGING SET
command and enable the client with the LOGGING ENABLE SYSLOG
command. You can specify only one syslog server. Before using the
syslog client, you should review the guidelines in the next section.
Syslog Client
Guidelines
126
The guidelines to using the syslog client are:
ˆ
The AT-MCF2000M Management Module must have an IP
configuration. For instructions, refer to Chapter 3, “IP Configuration
Commands” on page 47.
ˆ
The 10/100/1000Base-T Management port on the management
module must be connected to a network device on your network, such
as a Fast Ethernet or Gigabit Ethernet switch. The management
module communicates with the syslog server through this port.
ˆ
The syslog server must be a member of the same network as the
management module or have access to it through Layer 3 routing
devices.
AT-S85 and AT-S97 Management Software User’s Guide
ˆ
Command
Summary
If the management module and syslog server are on different
networks, the IP configuration on the management module must
include a default gateway specifying the IP address of the first hop to
reaching the server. For instructions, refer to Chapter 3, “IP
Configuration Commands” on page 47.
Table 15 summarizes the event log and syslog client commands.
Table 15. Event Log and Syslog Client Commands
Command
Description
LOGGING CLEAR
EVENTLOG on page 128
Clears all the events from the log.
LOGGING DISABLE
EVENTLOG on page 129
Disables the event log. No further
events are stored in the log.
LOGGING DISABLE SYSLOG
on page 130
Disables the syslog client. No
further events are sent to a syslog
server.
LOGGING ENABLE
EVENTLOG on page 131
Activates the event log which
begins to store event messages.
LOGGING ENABLE SYSLOG
on page 132
Activates the syslog client.
LOGGING SET EVENTLOG
on page 133
Specifies the severity level of the
event messages viewed in the log
and sent to a syslog server.
LOGGING SET SYSLOG on
page 135
Specifies the IP address of a
syslog server and a facility code
for the messages.
LOGGING SHOW on
page 136
Displays the status of the event
log and syslog client.
“LOGGING SHOW
EVENTLOG” on page 138
Displays the event messages in
the event log.
127
Chapter 7: Event Log and Syslog Client Commands
LOGGING CLEAR EVENTLOG
Syntax
logging clear eventlog
Parameters
None.
Privilege Level
Administrator
Description
This command is used to delete all of the messages in the event log. If the
log is activated, the management module immediately begins to store new
events.
Example
logging clear eventlog
128
AT-S85 and AT-S97 Management Software User’s Guide
LOGGING DISABLE EVENTLOG
Syntax
logging disable eventlog
Parameters
None.
Privilege Levels
Administrator and read-write
Description
This command is used to disable the event log to stop it from storing any
further events. Any events already stored in the log are retained.
To display the current state of the event log or the event messages, refer
to “LOGGING SHOW” on page 136. The default setting for the event log is
enabled.
Example
logging disable eventlog
129
Chapter 7: Event Log and Syslog Client Commands
LOGGING DISABLE SYSLOG
Syntax
logging disable syslog
Parameters
None.
Privilege Levels
Administrator and read-write
Description
This command is used to disable the syslog client to stop the management
module from transmitting any further event messages to a syslog server.
This is the default state of the client. To display the current state of the
syslog client, refer to “LOGGING SHOW” on page 136.
Example
logging disable syslog
130
AT-S85 and AT-S97 Management Software User’s Guide
LOGGING ENABLE EVENTLOG
Syntax
logging enable eventlog
Parameters
None.
Privilege Levels
Administrator and read-write
Description
This command is used to activate the event log. After you enter this
command, the management module immediately begins to store the
events as they occur. This is the log’s default setting. To display the log’s
current state, refer to “LOGGING SHOW” on page 136.
Example
logging enable eventlog
131
Chapter 7: Event Log and Syslog Client Commands
LOGGING ENABLE SYSLOG
Syntax
logging enable syslog
Parameters
None.
Privilege Levels
Administrator and read-write
Description
This command is used to activate the syslog client on the management
module. After you enter this command, the module immediately begins to
send the event messages as they occur to the syslog server. The default
setting for the syslog client is disabled.
The IP address of the syslog server is specified with “LOGGING SET
EVENTLOG” on page 133. To display the current status of the syslog
client, refer to “LOGGING SHOW” on page 136.
Note
For the requirements of the syslog client, refer to “Syslog Client
Guidelines” on page 126,
Example
logging enable syslog
132
AT-S85 and AT-S97 Management Software User’s Guide
LOGGING SET EVENTLOG
Syntax
logging set eventlog severity-level=critical|major|minor|
event
Parameters
severity-level Specifies the severity level of the event messages
displayed in the event log and sent to a syslog server. The
same level applies to both the event log and the syslog
client. The levels from highest to lowest severity are:
critical
Critical events signal the loss of power to or the
failure of a power module. Messages of this
level can also reflect a physical change to the
stacking feature, such as the removal of a
stacking cable or the introduction of a new
chassis to a stack.
major
Major events announce a component failure to a
fan or media converter module. Resets of and
powering on a module or chassis are also
categorized as major events.
minor
Minor events encompass physical changes to a
chassis, such as the installation or removal of a
module. Connecting and disconnecting cables
to the ports of the media converter channels are
also listed as minor events.
event
Event messages typically signal a change in the
status of a management component, such as
the Telnet or SSH server. The start and end
points of remote Telnet and Secure Shell
management sessions and TFTP functions are
also members of this category.
Selecting a level designates the messages of that level and
all levels above it. For example, selecting the Critical level
selects only Critical event messages, while selecting the
Event level, the default setting, spans all levels and,
therefore, all event messages.
Privilege Levels
Administrator and read-write.
133
Chapter 7: Event Log and Syslog Client Commands
Description
This command is used to set a severity level for the event log and the
syslog client. The severity level is used to control the messages that are
displayed by the event log with the LOGGING SHOW command and that
are sent to a syslog server. The same severity level applies to both the
event log and the syslog client.
The severity level is inclusive of the designated severity level and all levels
above it. For example, at the default setting of Event for the severity level,
the LOGGING SHOW command displays all of the messages in the event
log, because the Event severity is the lowest level. But if you were to set
the management module’s severity level to Major, the LOGGING SHOW
command would display just the Critical and Major messages.
This command also controls the messages sent by the management
module’s syslog client to a syslog server. At the default value of Event, all
messages are sent to a syslog server. But if you set the module’s severity
to Major, then only Critical and Major messages would be sent.
Examples
This command sets the severity level to critical:
logging set eventlog severity-level=critical
This command sets the severity level to major:
logging set eventlog severity-level=major
134
AT-S85 and AT-S97 Management Software User’s Guide
LOGGING SET SYSLOG
Syntax
logging set syslog [host=ipaddress] [facility-code=value]
Parameters
host
Specifies the IP address of a syslog server. To remove an
IP address without assigning a new address, specify the
default value of 0.0.0.0.
facility-code
Specifies a facility level to add to the event messages as
they are sent to a syslog server. The range is 0 to 23. The
default value is 0.
Privilege Levels
Administrator and read-write.
Description
This command is used to specify an IP address of a syslog server and a
facility code for the events.
The HOST parameter specifies an IP address of a syslog server. You can
enter only one IP address.
The FACILITY-CODE parameter adds a facility level to the events as they
are sent to a syslog server. A facility level is a numerical code commonly
used to group entries on the syslog server according to the source network
device. You can specify only one facility level. Refer to RFC 3164 for the
facility code definitions.
Examples
This command specifies the IP address of the syslog server as
149.22.22.44 and sets the facility code to 16 (local0):
logging set syslog host=149.22.22.44 facility-code=16
This command designates the IP address of the syslog server as
149.55.66.7:
logging set syslog host=149.55.66.7
This command sets the facility code for the messages to 21 (local5):
logging set syslog facility-code=21
135
Chapter 7: Event Log and Syslog Client Commands
LOGGING SHOW
Syntax
logging show
Parameters
None.
Privilege Levels
Administrator, read-write, and read-only.
Description
This command is used to display the status of the event log and the syslog
client. An example of the information is shown in Figure 21.
EventLog Information
Status .................. Enable
Severity Level .......... Event
Syslog Information
Status .................. Enable
Server .................. 149.22.122.8
Facility Code ........... 1
Figure 21. LOGGING SHOW Command
The fields in the EventLog Information section are:
ˆ
Status - The status of the event log. A status of Enable signifies that
the event log is storing event messages while a status of Disable
indicates that it is not storing messages. To set this value, refer to
“LOGGING ENABLE EVENTLOG” on page 131 and “LOGGING
DISABLE EVENTLOG” on page 129.
ˆ
Severity Level - The severity level of the messages displayed by the
event log and sent to a syslog server. The severity levels from highest
to lowest are Critical, Major, Minor, and Event. The affected messages
are inclusive of the selected severity level and all levels above it. For
example, the Event severity level, the default setting, encompasses all
of the levels and so all of the event messages, while a setting of Major
selects just the Critical and Major messages. To set this value, refer to
“LOGGING SET EVENTLOG” on page 133.
The fields in the Syslog Information section are:
ˆ
136
Status - The status of the syslog client. When the status of the client is
Enable, the management module can send events to a syslog server.
AT-S85 and AT-S97 Management Software User’s Guide
When the status is Disable, the management module cannot send
events to a syslog server. To set this parameter, refer to “LOGGING
ENABLE SYSLOG” on page 132 and “LOGGING DISABLE SYSLOG”
on page 130.
ˆ
Server - The IP address of the syslog server. To set this value, refer to
“LOGGING SET EVENTLOG” on page 133.
ˆ
Facility Code - The facility level added to the event messages as they
are sent to a syslog server. To set this value, refer to “LOGGING SET
EVENTLOG” on page 133.
Example
This command displays the status of the event log and the syslog client:
logging show
137
Chapter 7: Event Log and Syslog Client Commands
LOGGING SHOW EVENTLOG
Syntax
logging show eventlog
Parameters
None.
Privilege Levels
Administrator, read-write, and read-only
Description
This command is used to view the event messages in the event log. An
example of the log is shown in Figure 22. The events are displayed in
reverse-chronology, with the newest entries listed first. The event log, at
its default setting, displays all of its messages. To view the event
messages to particular severity levels, refer to “LOGGING SET
EVENTLOG” on page 133.
Date
Time
Status
Message
---------------------------------------------------------------04/21/2007 2:12:28::MN::RP::002/1::Port 7 Set to Missing Link
04/21/2007 2:12:26::MN::RP::001/1::Fiber Port 7 Online
04/21/2007 2:12:25::MN::RP::001/1::Copper Port 7 Online
04/21/2007 2:12:24::MN::RP::000/2::Fiber Port 5 Online
04/21/2007 2:12:24::MN::RP::000/2::Copper Port 5 Online
04/21/2007 2:12:22::EV::RP::000/M::SSH Server Enabled
Figure 22. LOGGING SHOW EVENT-LOG Command
The fields are defined here:
138
ˆ
Date - The date of the event.
ˆ
Time - The time of the event.
ˆ
Status - The event status, consisting of the severity level and the
message’s classification. The possible severity levels are listed in
Table 16.
AT-S85 and AT-S97 Management Software User’s Guide
Table 16. Severity Level Definitions
Severity Level
Definition
CR
Critical - Indicates critical events signal
the loss of power to or the failure of a
power module. Messages of this level can
also reflect a physical change to the
stacking feature, such as the removal of a
stacking cable or the introduction of new
chassis to a stack.
MJ
Major - Indicates major events announce
a component failure to a fan or media
converter module. Resets of and powering
on a module or chassis are also
categorized as major events.
MN
Minor - Indicates minor events encompass
physical changes to a chassis, such as
the installation or removal of a module.
Connecting and disconnecting cables to
the ports of the media converter channels
are also listed as minor events.
EV
Event - Indicates event messages
typically signal a change in the status of a
management component, such as the
Telnet or SSH server. The start and end
points of remote Telnet and Secure Shell
management sessions and TFTP
functions are also members of this
category.
The second part of an event’s status is its classification of report (RP)
or clear (CL). A report signals an event’s occurrence while a clear
signifies the resolution of a prior event. As an example, if a module’s
operating temperate were to exceed the temperate threshold, the
management module would log a “High Temperature Threshold” event
in the log with a classification of report, marking the occurrence of the
event. And when the temperature dips below the threshold, the module
logs the same event message, but with a clear classification signaling
the prior event’s resolution.
Only a few of the event messages can be both report and clear. For a
list of the messages, refer to Table 18 on page 140.
139
Chapter 7: Event Log and Syslog Client Commands
Message - The chassis and slot numbers of the source module of the
event message.
ˆ
Chassis and Slot IDs - The chassis ID and slot identifier of the source
module of the message. The first number is the chassis ID number
and the second is the slot number or letter, as shown in Figure 23.
Chassis ID
000/2
Slot Identifier
Figure 23. Chassis and Slot IDs
For background information on chassis ID numbers, refer to “Chassis
ID Numbers” on page 25. For the slot identifiers, refer to Table 17.
Table 17. Slot Identifiers
Identifier
Slot
1, 2, 3 or 4
Media converter slot.
A or B
Power supply or fan module slot.
M
Management module slot.
The event messages are listed in Table 18.
Table 18. Event Messages
Message
Definition
Classification
Critical Level Messages
Battery Low
Power Failure
140
The power charge in a module’s battery is low. The
battery may need replacing.
Report
The charge in the module’s battery returned to
normal or the battery was replaced.
Clear
The input voltage of a power supply module dropped
below or exceeded the permitted operating range.
Report
The input voltage of a power supply module returned
to the proper operating range.
Clear
AT-S85 and AT-S97 Management Software User’s Guide
Table 18. Event Messages (Continued)
Message
Stacking Port Link
Definition
Classification
A Stack port on the management module or the
AT-MCF2000S Stacking Module established or lost
its link to another Stack port.
Report
Chassis Managership
Acquire
A media converter module assumed control of the
backplane in the chassis to determine system
information, as it was initializing its management
software.
Report
Chassis Managership
Release
A media converter module released control of the
backplane.
Report
Chassis Reset
The chassis was reset with the SYSTEM RESET
CHASSIS command.
Report
Cold Boot
A media converter module loaded its boot loader and
management software after receiving power. It
generates this message when the chassis is
powered on or if it is installed while a unit is powered
on.
Report
Fan # Failure
A cooling fan in a power supply or fan module
stopped.
Report
A cooling fan resumed operating after having
stopped.
Clear
A module’s operating temperature exceeded the
temperature threshold set with the SYSTEM SET
MODULE command.
Report
A module’s operating temperature returned below its
temperature threshold.
Clear
Module Reset
A media converter module started the process of
initializing its boot loader and AT-S85 Management
Software after it was reset with the SYSTEM RESET
MODULE command. The completion of the
initialization process is signaled with the Warm Boot
message.
Report
Warm Boot
A media converter module completed the
initialization of its management software after being
reset with the SYSTEM RESET MODULE
command.
Report
Major Level Messages
High Temperature
Threshold
141
Chapter 7: Event Log and Syslog Client Commands
Table 18. Event Messages (Continued)
Message
Definition
Classification
Minor Level Messages
142
Authentication Failure
The management software denied access to an
individual who attempted to locally or remotely log on
to the management module with an invalid user
name or password.
Report
Copper|Fiber Port #
Offline
A port in a media converter channel lost its link to the
network device.
Report
Copper|Fiber Port #
Online
A port in a media converter channel established a
link to a network device.
Report
Copper|Fiber Port #
RX SML
A port in a media converter channel is receiving the
Smart MissingLink signal. This is an indication that
the port is connected to another media converter that
supports the Smart MissingLink mode, forming a
chain of media converters. Media converters that
support the Smart MissingLink mode pass the loss of
a link on a port to all the media converters in the
chain.
Report
Copper|Fiber Port #
TX SML
A port in a media converter channel is sending the
Smart MissingLink signal by pulsing its transmitter
once a second to indicate that its companion port in
the channel cannot establish a link with a network
device.
Report
Module Inserted
The management module detected a media
converter, power, or fan module while initializing its
management software after a power cycle or reset.
Alternatively, a module was installed in a slot in the
chassis while the chassis was powered on.
Report
Module Removed
The management module stopped detecting a media
converter, power, or fan module during a power
cycle or reset. Alternatively, a module was removed
from a slot in the chassis while the chassis was
powered on.
Report
Port # Mode Set to
<operating mode>
A channel’s operating mode was changed to Link
Test, Missing Link, or Smart Missing Link. “Port #”
refers to the channel number. For example, the
message “Port 1 Mode Set to Smart MissingLink”
signals that channel 1 on a media converter module
was set to the Smart MissingLink mode.
Report
AT-S85 and AT-S97 Management Software User’s Guide
Table 18. Event Messages (Continued)
Message
Definition
Classification
Event Level Messages
BM update its BM.cfg
in MM
The media converter module upgraded its
configuration in the management module.
Report
MM overwrite BM cfg
The management module configuration overwrote
the media module configuration.
Report
SSH Server Disabled
The SSH server, used for remote management of
the chassis or stack with an SSH client, was
disabled with the SSH DISABLE command.
Report
SSH Server Enabled
The SSH server was enabled with the SSH ENABLE
command.
Report
SSH Session Close
A remote SSH client ended a management session
with the management module.
Report
SSH Session Open
A remote SSH client established a management
session with the management module.
Report
Telnet Server Disabled
The Telnet server, used for remote management of
the chassis or stack from a Telnet client, was
disabled with the TELNET DISABLE command.
Report
Telnet Server Enabled
The Telnet server was enabled with the TELNET
ENABLE command.
Report
Telnet Session Open
A remote Telnet client established a management
session with the management module.
Report
Telnet Session Close
A remote Telnet client ended a management session
with the management module.
Report
TFTP Session Open
The management module uploaded or downloaded
a file during a local or remote management session
using TFTP. For example, you would see this
message if you downloaded new management
software onto the modules using TFTP.
Report
TFTP Session Close
The management module completed uploading or
downloading a file to a TFTP server.
Report
Xmodem Session
Open
The management module started to download a file
using XMODEM.
Report
Xmodem Session
Close
The management module completed downloading a
file using XMODEM.
Report
143
Chapter 7: Event Log and Syslog Client Commands
Example
This command displays the events in the event log:
logging show eventlog
144
Chapter 8
Configuration File Commands
This chapter contains the following sections:
ˆ
“Overview” on page 146
ˆ
“CONFIG OVERWRITE” on page 158
ˆ
“CONFIG RUN” on page 160
ˆ
“CONFIG SAVE” on page 161
ˆ
“CONFIG SAVE FILESYSTEM” on page 162
ˆ
“CONFIG SET” on page 164
ˆ
“CONFIG SHOW” on page 166
145
Chapter 8: Configuration File Commands
Overview
The parameter settings of the management module and the media
converter modules are stored in a series of files called configuration files.
These files enable the modules to retain their settings even when they are
moved to a different slot or chassis or when a chassis is reset or power
cycled. This saves you from having to constantly reconfigure the units.
Management
Module and the
Master
Configuration
File
In the file system of the management module is the master configuration
file. Stored in this file are the parameter settings for the management
module itself and the settings of all the media converter modules in a
chassis.
Media
Converter
Modules and
Auxiliary
Configuration
Files
The parameter settings of the media converter modules are stored in two
locations. One of the locations is on the management module in the
master configuration file.
The management module does not come with a predefined-master
configuration file. Creating it is a required step in the initial configuration of
a chassis. For instructions, refer to “Creating a Master Configuration File”
on page 32 or “Creating a New Master Configuration File” on page 148.
The other location is on the media converter modules themselves in what
are referred to as the auxiliary configuration files. These files are stored in
flash memory and, thus, they retain their contents even when the modules
are powered off or even when they are removed from a chassis. Because
of these files, modules can be moved from chassis to chassis and still
retain their configuration settings.
When a media converter module is powered on or reset, it looks to either
its auxiliary configuration file or to the management module and the
master configuration file for the parameter settings it should use. The
choice is based on its configuration overwrite setting. If this setting is
disabled, the module uses its auxiliary configuration file. And if it is
enabled, the module uses the master configuration file.
The value of the overwrite setting is that it can save you time if you have to
replace a module. If a new module’s overwrite setting is enabled, it is
automatically configure with the same settings as the module it replaced.
Here is the process that a media converter module goes through to set its
configuration settings when powered on:
1. It initializes its management software. That takes about one minute.
2. It examines its overwrite setting.
146
AT-S85 and AT-S97 Management Software User’s Guide
3. If the overwrite setting is disabled, the module configures its
parameters using its auxiliary configuration file and, afterwards, begins
normal network operations.
4. If the overwrite setting is enabled, the module queries for a
management module over the backplane in the chassis.
5. If there is no response to the query, meaning that the chassis does not
have a management module, the media converter module again uses
its auxiliary configuration file to configure its parameters.
6. If the chassis has a management module, the module responds to the
query by extracting from the master configuration file the parameter
settings for that slot in the chassis and sending them over the
backplane to the media converter module.
7. The media converter examines the settings. If the slot had never been
used before or if the settings are for a different media converter model,
the module discards the settings and instead uses its auxiliary
configuration file.
8. If the settings are from the same model of media converter module, the
module implements the parameter settings.
Note
You should never need to rename, copy, delete, or upload an
auxiliary configuration file from the file system of a media converter
module. Make any parameter changes directly to the master
configuration file in the file system on the management module,
either through the command line interface or by editing the file.
Note
The AT-MCF2012LC and AT-MCF2012LC/1 Media Converter
Modules are considered different models by the management
software.
Saving Your
Parameter
Changes
When you change a parameter setting on a management module or a
media converter module, the device immediately implements your change.
The master and auxiliary configuration files, however, are not updated
automatically. Instead, you must initiate the update yourself. This is
accomplished with this command:
config save
When you issue this command, all the modules in the chassis or stack
update their configuration files to match their current operating
parameters.
147
Chapter 8: Configuration File Commands
When you issue the CONFIG SAVE command to save your parameter
changes, the management module updates the master configuration file
using the auxiliary configuration files from the media converter modules.
Here is an outline of the process:
1. When the CONFIG SAVE command is issued, all the modules in the
chassis or stack update their auxiliary configuration files to reflect their
current parameter settings. The filenames are “BM.CFG” for a media
converter’s file and “MM.CFG” for the management module’s file.
These file naming conventions cannot be changed.
2. The media converter modules transmit a copy of their updated
auxiliary configuration files to the management module through the
backplane in the chassis.
3. When the management module stores an auxiliary configuration file in
its file system, it adds the chassis ID number and the slot number of
the source module to the filename in order to distinguish between the
various files. An example is “BM_0_1.CFG.” The first number is the
chassis ID and the second is the slot number of the module. This file
naming convention cannot be changed.
4. After the management module has received the updated auxiliary
configuration files from all of the media converter modules, it forms a
new, updated master configuration file for the entire chassis or stack
by concatenating the files.
The entire process is usually completed in a of couple seconds, but it can
vary depending on the number of media converter modules in the chassis
or stack and the number of parameter settings.
Creating a New
Master
Configuration
File
There are several ways to create a new master configuration file on a
management module. One method is with the CONFIG SAVE
FILESYSTEM command. What this command does is it creates a new
master configuration file with all of the current settings of the modules in
the chassis or stack.
Here is an example of the command. It creates the new master
configuration file “mcf_ai_traffic.cfg” on a management module in a
chassis with the ID 0:
config save filesystem=system://0/m/mcf_ai_traffic.cfg
Another way to create a new master configuration file is to edit an existing
file with a text editor by uploading it from the file system on the
management module to your management workstation, editing it with a
text editor, and downloading it again to the management module. The
instructions for uploading or downloading a file to a module’s file system
are found in Chapter 9, “File System Commands” on page 169. For
information about editing the file, refer to “Editing a Master Configuration
File” on page 150.
148
AT-S85 and AT-S97 Management Software User’s Guide
You can also create a new master configuration file by copying an existing
file in the management module’s file system with the FILE COPY
command. This example creates a copy of the source file
“mcf_ai_traffic.cfg.” The new file is “mcf_24a_traffic.cfg.”
file copy srcfile=system://0/m/mcf_ai_traffic.cfg
dstfile=system://0/m/mcf_24a_traffic.cfg
This command is described in Chapter 9, “File System Commands” on
page 169.
Specifying the
Active Master
Configuration
File
A management module can have more that one master configuration file in
its file system, but only one of the files can be active at a time. This file is
referred to as the active master configuration file. It is this file that the
management software updates in response to the CONFIG SAVE
command and refers to when configuring the parameter settings of the
modules.
The command for specifying the active master configuration file on the
management module is the CONFIG SET command. After you have
designated a new active master configuration file on a management
module, you should do one of the following:
ˆ
If you want the management module to configure the modules in the
chassis with the settings in the new active file, issue the CONFIG RUN
command.
Note
Issuing the CONFIG RUN command may momentarily disrupt the
flow of traffic through the media converter channels as the modules
reconfigure their settings.
ˆ
If you want to overwrite the settings in the file with the current settings
of the modules, issue the CONFIG SAVE command, instead. This
might be appropriate in situations where you did not want to use the
settings in the new active master configuration file, and instead want to
overwrite the settings in the file with the current configuration.
Naturally, this does not result in a disruption of network traffic through
the media converter channels.
To view the name of the active master configuration file, use the CONFIG
SHOW command.
149
Chapter 8: Configuration File Commands
Editing a Master
Configuration
File
You can edit the master configuration file on the management module with
a text editor at your management station by uploading the file from the
management module using a TFTP server. You cannot edit it directly on
the management module. After you have edited the file, you can download
it to the management module and designate it as the active master
configuration file on the module.
For instructions on how to upload and download a master configuration file
to a management module, refer to “FILE UPLOAD” on page 194 and
“FILE DOWNLOAD” on page 179. To designate the active master
configuration file of the management module, refer to “CONFIG SET” on
page 164.
The following sections describe the various parts of a master configuration
file and the supported commands for each of the sections.
File Header Lines
At the top of the file are three lines of header information, shown in
Figure 24. These lines should never be modified or deleted.
## Filename: MM.cfg
## Model Type: AT-MCF2000M
## MAC Address: 00:15:77:70:7A:25
Figure 24. Management Module Configuration Header
System Configuration
The commands in this section define general information about the
management module.
### System
system set
system set
system set
system set
system set
system set
system set
system set
system set
system set
Configuration
asynchronous baudrate = 115200
console timeout=10
contact "none"
hostname "none"
location "none"
mymodule id=1/0 name="none"
mymodule id=1/0 temperature-threshold=60
mymodule id=1/a temperature-threshold=60
mymodule id=1/b temperature-threshold=60
rtc source=none
Figure 25. System Configuration Section
150
AT-S85 and AT-S97 Management Software User’s Guide
The section accepts the following AT-S97 Management Software
commands:
ˆ
“SYSTEM SET ASYNCHRONOUS” on page 58
ˆ
“SYSTEM SET CONSOLE” on page 62
ˆ
“SYSTEM SET CONTACT” on page 63
ˆ
“SYSTEM SET HOSTNAME” on page 64
ˆ
“SYSTEM SET LOCATION” on page 65
ˆ
“SYSTEM SET MODULE” on page 89
The module’s name is set with a modified version of the SYSTEM SET
MODULE command, where the MODULE keyword is replaced with
MYMODULE and the management module slot is indicated in the ID
parameter with “0” (zero) rather than “M”. This modified command also
sets the temperature thresholds of the management module and the
power supply and fan modules. The command with the slot ID of “0” (zero)
sets the temperature threshold for the management module while the
commands with the slot IDs of “A” and “B” (for example, “1/A” and “1/B”)
set this parameter for the power supply and fan modules. For further
information on this command, refer to “SYSTEM SET MODULE” on
page 89.
The SYSTEM SET RTC command is found only in the master
configuration file and dictates the source of the time and date of the
management module. The two possible settings are NONE, indicating that
the date and time are set manually, and NTP, signifying that the date and
time are set from an NTP server.
IP Configuration
The commands in this section define the IP configuration of the
management module.
### Ip Configuration
ip dhcp disable
ip set ip-address=192.168.1.2
ip set subnetmask=255.255.255.0
ip set default-gateway=0.0.0.0
Figure 26. IP Configuration Section
This section accepts the following commands:
ˆ
“IP DHCP DISABLE” on page 50
ˆ
“IP DHCP ENABLE” on page 51
ˆ
“IP SET” on page 52
151
Chapter 8: Configuration File Commands
Log Configuration
This section controls the event log and the syslog client.
### Log
logging
logging
logging
logging
logging
Configuration
enable eventLog
enable sysLog
set sysLog host=0.0.0.0
set sysLog facility-code=0
set eventLog severity-level=event
Figure 27. Log Configuration Section
The section accepts the following commands:
ˆ
“LOGGING DISABLE EVENTLOG” on page 129
ˆ
“LOGGING DISABLE SYSLOG” on page 130
ˆ
“LOGGING ENABLE EVENTLOG” on page 131
ˆ
“LOGGING ENABLE SYSLOG” on page 132
ˆ
“LOGGING SET EVENTLOG” on page 133
ˆ
“LOGGING SET SYSLOG” on page 135
NTP Configuration
This section controls the NTP client for setting the modules date and time
from an NTP server on your network or the Internet.
###
ntp
ntp
ntp
Ntp Configuration
set server=0.0.0.0
set utcoffset=0
disable
Figure 28. NTP Configuration Section
This section accepts the following commands:
152
ˆ
“NTP DISABLE” on page 120
ˆ
“NTP ENABLE” on page 121
ˆ
“NTP SET” on page 122
AT-S85 and AT-S97 Management Software User’s Guide
Telnet and SSH Configuration
This section controls the Telnet and SSH servers for remote management
of the chassis from a Telnet or SSH client.
### Telnet & SSH Configuration
telnet disable
ssh disable
Figure 29. Telnet and SSH Configuration Section
This section accepts the following commands:
ˆ
“TELNET DISABLE” on page 200
ˆ
“TELNET ENABLE” on page 201
ˆ
“SSH DISABLE” on page 212
ˆ
“SSH ENABLE” on page 213
User Configuration
This section controls the manager accounts.
### User Configuration
user config name=manager priv=admin pwd=3af00c6cad11f7ab5db4467b66ce503eff
Figure 30. User Configuration Section
Note
Do not modify the existing manager accounts or add new accounts
by editing the master configuration file. Instead, use the command
line interface in the management software. You can delete accounts
by deleting the corresponding line in the file, but do not delete the
predefined manager account (that is, NAME=MANAGER). For
further information, refer to Chapter 13, “Manager Account
Commands” on page 215.
SNMP Configuration
This section, shown in Figure 31, controls the SNMPv1 and v2c
parameters, used to set the community strings for remote SNMP
management and to identify the IP addresses of the trap receivers on your
network.
153
Chapter 8: Configuration File Commands
### SNMP
snmp set
snmp set
snmp set
snmp set
snmp set
snmp set
snmp set
Configuration
mgrip1=0.0.0.0
mgrip2=0.0.0.0
mgrip3=0.0.0.0
mgrip4=0.0.0.0
get-community=public
set-community=private
trap-community=public
Figure 31. SNMP Configuration Section
This section accepts the SNMP SET command. For information on the
command, refer to “SNMP SET” on page 206
Blade Configuration
This section controls the operating parameters of the channels and ports
on a media converter module. A master configuration file has a separate
Blade Configuration section for each of the media converter modules in a
chassis or stack.
The section is prefaced with three header lines that identify the media
converter module controlled by the commands in the section. An example
is shown in Figure 32.
## Filename: BM_0_2.cfg
## Model Type: AT-MCF2012LC
## MAC Address: 00:15:77:70:7A:2C
Figure 32. Blade Configuration Header
The Filename line identifies the name of the auxiliary configuration file
used to create that portion of the master file as well as the media converter
module controlled by the commands. The numbers in the filename identify
the module. The first number represents the chassis ID and the second
number the slot number. For example, the auxiliary configuration filename
“BM_0_2.cfg” in Figure 32 identifies the media converter module in slot 2
of the chassis with an ID number of 0.
The Model Type field specifies the model name of the media converter
module and the MAC Address specifies its MAC address.
Note
The header lines of a Blade Configuration section should not be
modified or deleted.
154
AT-S85 and AT-S97 Management Software User’s Guide
The first subsection in a Blade Configuration is illustrated in Figure 33. It
sets the operating modes of the media converter channels on the module
with a modified version of the SYSTEM SET INTERFACE command. The
ID parameter of the command is replaced with a PORTID parameter,
which specifies the channel number. For example, PORTID=1 designates
channel 1, which on the AT-MCF2012LC and AT-MCF2012LC/1 Media
Converter Modules represents twisted pair port 1 and fiber optic port 1,
PORTID=2 designates channel 2 of twisted pair port 2 and fiber optic port
2, and so on.
### Blade Configuration
system
system
system
system
system
set
set
set
set
set
interface
interface
interface
interface
interface
portId=1
portId=2
portId=3
portId=4
portId=5
OpMode=link-test
OpMode=link-test
OpMode=link-test
OpMode=link-test
OpMode=link-test
Figure 33. Blade Configuration - Operating Mode Section
Review the following guidelines before modifying the commands in this
section:
ˆ
Each channel must have its own command line.
ˆ
If you delete a command, the corresponding channel’s operating mode
will be Link Test, the default value.
ˆ
As previously mentioned, the PORTID parameter must specify just the
channel number. Do not include a chassis ID number or slot number.
The latter are defined in the header lines of the Blade Configuration
section.
The next subsection in a Blade Configuration, shown in Figure 34,
configures the operating parameters of the ports on the media converter
module, both twisted pair and fiber optic. The port operating parameters
are set with a modified version of the SYSTEM SET PORT command,
where the values in the ID parameter are truncated to the channel number
and port letter. For a description of this command, refer to “SYSTEM SET
PORT” on page 92.
155
Chapter 8: Configuration File Commands
system set
system set
limit=none
system set
system set
system set
limit=none
system set
system set
limit=none
system set
system set
system set
limit=none
port id=1/a ingress-rate-limit=none egress-rate-limit=none
port id=1/b duplex=full ingress-rate-limit=none egress-rateport id=2/a speed=100 duplex=full crossover=mdi
port id=2/a ingress-rate-limit=128k egress-rate-limit=none
port id=2/b duplex=full ingress-rate-limit=none egress-rateport id=3/a ingress-rate-limit=none egress-rate-limit=none
port id=3/b duplex=full ingress-rate-limit=none egress-rateport id=4/a speed=10 duplex=full crossover=mdi
port id=4/a ingress-rate-limit=none egress-rate-limit=none
port id=4/b duplex=full ingress-rate-limit=none egress-rate-
Figure 34. Blade Configuration - Port Operating Parameters
Here are the guidelines for modifying the commands in this section:
ˆ
Each port must have its own command line.
ˆ
A port can have more than one command line.
ˆ
A command line cannot exceed eighty characters.
ˆ
If you delete a port’s configuration command from the file, the port
operates with the default settings.
ˆ
The ID parameter specifies just the channel number and the port letter.
The name of a media converter module and the temperature threshold are
controlled with the commands in the final part of a Blade Configuration
section, shown in Figure 35.
system set mymodule id=1/0 name="none"
system set mymodule id=1/0 temperature-threshold=60
system set mymodule id=1/a temperature-threshold=60
system set mymodule id=1/b temperature-threshold=60
system set mymodule id=1/c temperature-threshold=60
configuration overwrite disable
Figure 35. Blade Configuration - Module Name and Temperature
Threshold Section
The first two lines control the module’s name and temperature threshold.
The commands are a modified version of the SYSTEM SET MODULE
command, with the MYMODULE keyword substituting for the MODULE
keyword, as explained earlier in the System Configuration section. Do not
change the ID values. Though in all other cases a slot “0” designation
indicates the management module, this is not true for these lines in the
156
AT-S85 and AT-S97 Management Software User’s Guide
Blade Configuration section. Here, the “0” slot designation signifies the
module itself, in this case a media converter module.
The lines with the IDs 1/A, 1/B and 1/c can be ignored.
The final line controls the overwrite setting of the module. For instructions,
refer to “CONFIG OVERWRITE” on page 158.
Guidelines to Editing a Master Configuration File
The following guidelines apply to editing a configuration file:
Command
Summary
ˆ
The text editor must be able to store the file as ASCII text. Do not use
special formatting codes, such as boldface or italics.
ˆ
A command cannot exceed eighty characters.
ˆ
Each command must start flush left against the margin.
ˆ
To comment out a command so that the media converter does not
perform it, precede the command with three pound symbols (#).
Table 19 summarizes the configuration file commands.
Table 19. Configuration File Commands
Command
Description
“CONFIG OVERWRITE” on
page 158
Overrides the automatic
overwriting of a media converter
module configuration file.
“CONFIG RUN” on page 160
Configures the parameter settings
on all the modules using the active
master configuration file on the
management module
CONFIG SAVE on page 161
Updates the active configuration
file with the latest changes to the
parameter settings. Also creates
new master configuration files.
“CONFIG SAVE
FILESYSTEM” on page 162
Creates a new master
configuration file.
CONFIG SET on page 164
Selects a new active master
configuration file.
CONFIG SHOW on page 166
Displays the name of the active
and current master configuration
files on the management module.
157
Chapter 8: Configuration File Commands
CONFIG OVERWRITE
Syntax
config overwrite enable|disable id=chassis/slot
Parameters
enable
Activates configuration overwrite on a media converter
module. At this setting, a module, when it is powered on or
reset, seeks its configuration settings from a management
card and a master configuration file. This is the default
value.
disable
Deactivates configuration overwrite on a media converter
module. At this setting, a module uses the configuration
settings in its auxiliary configuration file in flash memory to
set its parameter settings whenever it is powered on or
reset.
id
Identifies a media converter module. You can configure
only one module at a time. An ID number has the following
parts:
chassis
Identifies an ID number of a chassis. The range
is 0 to 31. For background information, refer to
“Chassis ID Numbers” on page 25.
slot
Identifies a slot number of a module to be
configured. For background information, refer to
“Slot Numbers and Letters” on page 26. The
possible values are:
1 or 2
Specifies a media converter slot in
the AT-MCF2000 Chassis. The left
slot is 1 and the right slot is 2.
1 to 4
Specifies a media converter slot in
the AT-MCF2300 Chassis. The slots
are number 1 (left) and 2 (right) in
the top row, and 3 (left) and 4 (right)
in the bottom row.
Privilege Levels
Administrator and read-write.
158
AT-S85 and AT-S97 Management Software User’s Guide
Description
As explained in “Overview” on page 146, the configuration settings of the
media converter modules are stored in two locations. One of the locations
is the master configuration file on the AT-MCF2000M Management
Module and the other is the auxiliary configuration files on the media
converter module themselves. When a media converter module is reset or
powered on, it configures its settings from one of those sources. The
source that it goes to is based on the configuration overwrite setting on the
module, which this command controls.
When the overwrite setting is disabled, a media converter uses its own
auxiliary configuration file in flash memory for its configuration settings.
When the overwrite setting is enabled, a media converter queries the
management card and the master configuration file for its settings. This
happens to be the default setting.
Example
This command disables configuration overwrite on a media converter
module in slot 2 in a chassis with the ID 0:
config overwrite disable id=0/2
This command enables configuration overwrite on a media converter
module in slot 3 in a chassis with the ID 2:
config overwrite enable id=2/3
159
Chapter 8: Configuration File Commands
CONFIG RUN
Syntax
config run
Parameters
None.
Privilege Levels
Administrator and read-write.
Description
This command is used to configure the parameters settings of the
modules in the chassis or stack from the active master configuration file on
the management module. In some ways, this command is analogous to
resetting the chassis or stack, but with two important differences. The first
is that with this command the modules return to their normal network
operations quicker because they do not have to initialize their
management software. The second is that this command ignores the
configuration overwrite settings on the media converter modules, so that
modules with an overwrite setting of disabled still receive their settings
from the master configuration file.
There are two situations where you might use this command. The first is
after designating a new active master configuration file. To configure the
modules according to the settings in the new file, you could either reset
the chassis or stack, or you could issue this command.
The other situation where you might use this command is if you want to
return the modules to their previous configurations after making changes
that you did not save. For example, you might modify but not save the
settings of the ports on a media converter module, and later decide to
discard your changes.
Example
config run
160
AT-S85 and AT-S97 Management Software User’s Guide
CONFIG SAVE
Syntax
config save
Parameters
None.
Privilege Levels
Administrator and read-write.
Description
This command is used to update the active master configuration file on the
management module and the auxiliary configuration files on the media
converter modules with the current parameter settings of all of the devices.
Parameter settings that are saved in the configuration files are retained
even when the chassis or stack is reset or powered off. You should enter
this command when you are finished managing the devices and want to
save your changes. For background information, refer to “Overview” on
page 146.
Example
config save
161
Chapter 8: Configuration File Commands
CONFIG SAVE FILESYSTEM
Syntax
config save filesystem=system://chassis/slot/filename.cfg
Parameter
filesystem
Specifies a location and a name for a new master
configuration file. The parameter consists of the following
parts:
chassis
Specifies an ID number of a chassis with a
management module. The ID number is
either 0 or 31.
slot
Identifies a slot with a management module.
The only supported value for the slot is:
m
filename.cfg
Identifies the management
module slot and the
AT-MCF2000M Management
Module.
Specifies a name for a new master
configuration file. The name can be up to 15
alphanumeric characters, not including the
extension. Spaces are allowed, but a name
with spaces must be enclosed in double
quotes. The filename must include the
“.CFG” extension. Configuration filenames
are case sensitive.
To view the ID number and the slot numbers of a chassis,
refer to “SYSTEM SHOW CHASSIS” on page 99 or
“SYSTEM SHOW CLUSTER” on page 101. To view the
filenames of the current configuration files in a file system
on a module, refer to “FILE SHOW” on page 191.
Privilege Levels
Administrator and read-write.
Description
This command is used to create a new master configuration file containing
the current parameter settings of all the modules in a chassis or stack. The
file is stored in the file system on the management module. For
background information, refer to “Overview” on page 146.
162
AT-S85 and AT-S97 Management Software User’s Guide
If, after creating a new master configuration file, you want to designate it
as the active file on the management module, perform the CONFIG SET
command. For instructions, refer to “CONFIG SET” on page 164.
Example
This command creates the new master configuration file “mcf pat
traffic.cfg” with the current settings of all the modules in the chassis or
stack. The chassis with the management module has the ID number 0:
config save filesystem=system://0/m/"mcf pat traffic.cfg"
163
Chapter 8: Configuration File Commands
CONFIG SET
Syntax
config set filesystem=system://chassis/slot/filename.cfg
Parameter
filesystem
Specifies a location and a name of a master configuration
file. This parameter consists of the following parts:
chassis
Specifies an ID number of a chassis with a
management module. The ID number is
either 0 or 31.
slot
Identifies a slot with a management module.
The only supported value for the slot is:
m
filename.cfg
Identifies the management
module slot and the
AT-MCF2000M Management
Module.
Specifies the name of a active master
configuration file. The filename must include
the “.CFG” extension and is case sensitive.
To view the filenames of the configuration
files in a file system on a management
module, refer to “FILE SHOW” on page 191.
If the filename has spaces, enclose it in
double quotes (“ “).
To view the ID and slot numbers of a chassis, refer to
“SYSTEM SHOW CHASSIS” on page 99 or “SYSTEM
SHOW CLUSTER” on page 101.
Privilege Levels
Administrator and read-write.
Description
This command designates the active master configuration file on the
management module. For an explanation of the master configuration file,
refer to “Overview” on page 146.
164
AT-S85 and AT-S97 Management Software User’s Guide
After designating an active master configuration file, do one of the
following:
ˆ
To configure the modules in the chassis or stack according to the
settings in the newly designated active master configuration file, issue
the CONFIG RUN command. For instructions, refer to “CONFIG RUN”
on page 160. Do not issue the CONFIG SAVE command.
ˆ
To overwrite the settings in the active master configuration file with the
current settings of the modules, issue the CONFIG SAVE command.
For instructions, refer to “CONFIG SAVE” on page 161.
Note the following before using this command:
ˆ
To view the name of an active master configuration file, see “CONFIG
SHOW” on page 166.
ˆ
The designated file must already exist. To view the configuration files
in the management module’s file system, see “FILE SHOW” on
page 191. Configuration files have a “.cfg” extension. To create a new
configuration file, refer to “CONFIG SAVE” on page 161.
For further information, refer to “Specifying the Active Master
Configuration File” on page 149.
Examples
This command designates the file “mc22.cfg” in the file system on the
management module as the active master configuration file. The chassis
has the ID number 0:
config set filesystem=system://0/m/mc22.cfg
This command designates the file “mcf2000 b12.cfg” as the active master
configuration file for the chassis with the ID number 0:
config set filesystem=system://0/m/"mcf2000 b12.cfg"
165
Chapter 8: Configuration File Commands
CONFIG SHOW
Syntax
config show
Parameters
None
Privilege Levels
Administrator, read-write, and read-only.
Description
This command is used to display the names of the current and active
master configuration files on the management module. An example is
shown in Figure 36.
Last configuration file ran ............. unit12.cfg
Current set configuration file .......... unit12.cfg (Exists)
Active master configuration file
Figure 36. CONFIG SHOW Command
The “Last configuration file ran” field displays the name of the master
configuration file used by the management module to configure the
chassis during the last reset or power cycle.
The “Current set configuration file” field displays the name of the active
master configuration file. It is this file that the management module
updates when the CONFIG SAVE command is issued. This is also the file
that is used to configure the chassis during the next reset or power cycle.
Here is an example of how the process works. Assume the chassis is
currently using a master configuration file called “unit12.cfg,” as illustrated
in Figure 36.
Now assume you decide to configure the settings on the chassis modules
using a different master file called “mcf24.cfg.” If, after specifying the file
as the new active configuration file with the CONFIG SET command, you
issue the CONFIG SHOW command, the information in Figure 37 on page
167 is displayed.
166
AT-S85 and AT-S97 Management Software User’s Guide
Last configuration file ran ............. unit12.cfg
Current set configuration file .......... mcf24.cfg (Exists)
Figure 37. CONFIG SHOW Command with a New Active Master File
If you were to issue the CONFIG SAVE command at this point, the settings
in the “mcf24.cfg” file would be overwritten by the current settings of the
modules. Basically, the settings in the active configuration file would be
replaced by the settings of the master configuration file used during the
last reset, in this case “unit12.cfg,” in addition to any changes that were
make since the last reset or power cycle. And, in some situations, this
might be the goal.
But if the goal is to configure the modules with the settings in “mcf24.cfg,”
you issue the CONFIG RUN command so that the management module
configures the modules with the settings in the file. If, after issuing the
CONFIG RUN command, you again entered the CONFIG SHOW
command, the information in Figure 38 is displayed.
Last configuration file ran ............. mcf24.cfg
Current set configuration file .......... mcf24.cfg (Exists)
Figure 38. CONFIG SHOW Command with a New Current and Active
Master File
Example
config show
167
Chapter 8: Configuration File Commands
168
Chapter 9
File System Commands
This chapter contains the following sections:
ˆ
“Overview” on page 170
ˆ
“FILE COPY” on page 173
ˆ
“FILE DELETE” on page 176
ˆ
“FILE DOWNLOAD” on page 179
ˆ
“FILE FASTDOWNLOAD” on page 186
ˆ
“FILE RENAME” on page 188
ˆ
“FILE SHOW” on page 191
ˆ
“FILE UPLOAD” on page 194
169
Chapter 9: File System Commands
Overview
The following sections describe the functions of the commands in this
chapter.
Managing a
Module’s File
System
You can use the commands in this chapter to display the configuration
files in the file system on a management module, as well as copy, rename,
and delete files. For example, you might create a copy of a master
configuration file to maintain a history of the configuration settings of a
chassis, or delete old master configuration files to keep the file system
from becoming cluttered with obsolete files.
You can also use these commands to view the file system on a media
converter module. However, this is unlikely ever to be necessary.
For more information on configuration files, refer to Chapter 8,
“Configuration File Commands” on page 145.
Updating the
AT-S85 and
AT-S97
Management
Software
Allied Telesis may periodically release and post on our web site new
versions of the boot loaders and management software for the
management and media converter modules in the AT-MCF2000 Series.
You can update the software on your products by obtaining the newest
files from the Allied Telesis web site.
New management software is downloaded onto the modules with the FILE
DOWNLOAD command using the TFTP client in the AT-S97 Management
Software together with a TFTP server on your network. For instructions,
refer to “FILE DOWNLOAD” on page 179
Note
To avoid possible compatibility problems between the management
and media converter modules, Allied Telesis recommends that all
modules in a chassis or stack use the same version of the AT-S85
and AT-S97 Management Software. If the modules are running
different versions, you must upgrade the operating software on all
modules. To determine the version numbers of the modules’
software, use the SYSTEM SHOW CLUSTER command. For
instructions, refer to “SYSTEM SHOW CLUSTER” on page 101.
170
AT-S85 and AT-S97 Management Software User’s Guide
Uploading or
Downloading a
Master
Configuration
File
The master configuration file on the management module can be modified
with a text editor at your management workstation by uploading the file
from the file system on the management module to a TFTP server. After
you have edited the file, you can download it to the management module.
Uploading and downloading the configuration file is achieved with the
commands in this chapter. The full sequence of commands is:
1. Upload a master configuration file from the management module to a
TFTP server using the FILE UPLOAD command. For instructions, refer
to “FILE UPLOAD” on page 194.
2. Edit the file at your workstation. For instructions, refer to “Editing a
Master Configuration File” on page 150.
3. Download the file to the management module using the FILE
DOWNLOAD command. For instructions, refer to “FILE DOWNLOAD”
on page 179.
4. Designate the file as the active master configuration file on the module
with the CONFIG SET command. For instructions, refer to “CONFIG
SET” on page 164.
5. Configure the modules using the CONFIG RUN command. For
instructions, refer to “CONFIG RUN” on page 160.
Guidelines to
Using the TFTP
Client
The following guidelines apply to the TFTP client on the management
module when uploading or downloading files to the management module
with the FILE UPLOAD, FILE DOWNLOAD, and DILE FASTDOWNLOAD
commands:
ˆ
Your network must have a node with TFTP server software.
ˆ
To download a file, you must store the file on the TFTP server.
ˆ
Start the TFTP server software before performing the upload or
download command.
ˆ
The 10/100/1000Base-T Management port on the AT-MCF2000M
Management Module must be connected to the network. The
management module communicates with the TFTP server through this
port.
ˆ
The AT-MCF2000M Management Module must have an IP
configuration. For instructions, refer to Chapter 3, “IP Configuration
Commands” on page 47.
ˆ
The TFTP server must be a member of the same network as the
management module or have access to it through Layer 3 routing
devices.
ˆ
If the management module and TFTP server are on different networks,
the IP configuration on the management module must include a default
gateway specifying the IP address of the first hop to reaching the
171
Chapter 9: File System Commands
server. For instructions, refer to Chapter 3, “IP Configuration
Commands” on page 47.
Command
Summary
Table 20 summarizes the file system commands.
Table 20. File System Commands
Command
172
Description
“FILE COPY” on page 173
Creates copies of the
configuration files in the file
systems of the management and
media converter modules.
“FILE DELETE” on page 176
Deletes the configuration files from
the file systems on the modules.
“FILE DOWNLOAD” on
page 179
Downloads new versions of the
AT-S85 and AT-S97 Management
Software from a TFTP or Xmodem
server to the management and
media converter modules. You can
also download a modified master
configuration file to the
management module.
“FILE RENAME” on page 188
Renames the configuration files in
the modules’ file systems.
“FILE SHOW” on page 191
Displays the names of the files
stored in the file systems.
“FILE UPLOAD” on page 194
Primarily used to upload the
master configuration file from the
management module to a TFTP
server for editing at a
management workstation. Can
also be used to upload
configuration files between
modules.
AT-S85 and AT-S97 Management Software User’s Guide
FILE COPY
Syntax
file copy srcfile=system://chassis/slot/filename.cfg
dstfile=system://chassis/slot/filename.cfg
Parameter
srcfile=system
Specifies a location and name of a master configuration file
to copy. This parameter has the following parts:
chassis
Specifies an ID number of a chassis. The
range is 0 to 31. For background
information, refer to “Chassis ID Numbers”
on page 25.
slot
Identifies a slot with a module containing the
file. For background information, refer to
“Slot Numbers and Letters” on page 26.
Possible values are:
filename.cfg
m
Identifies the AT-MCF2000M
Management Module.
1 or 2
Specifies a slot number of a
media converter module in the
AT-MCF2000 Chassis. The left
slot is 1 and the right slot is 2.
1 to 4
Specifies a slot number of a
media converter module in the
AT-MCF2300 Chassis. The slots
are number 1 (left) and 2 (right)
in the top row, and 3 (left) and 4
(right) in the bottom row.
Specifies a name of a master configuration
file to be copied. Filenames with spaces
must be enclosed in double quotes.
Filenames are case sensitive and must
include the “.CFG” extension.
To view the ID number and slot numbers of a chassis, refer
to “SYSTEM SHOW CHASSIS” on page 99 or “SYSTEM
SHOW CLUSTER” on page 101. To view the filenames in a
file system on a module, refer to “FILE SHOW” on
page 191.
173
Chapter 9: File System Commands
dstfile=system
Specifies the name of the new copy of the master
configuration file. The destination must have the same
chassis and slot location as the source. The name can be
up to 15 alphanumeric characters, not including the
extension. Spaces are allowed, but a name with spaces
must be enclosed in double quotes. The filename must be
unique from all other files in the file system of the module
and it must include the “.CFG” extension. The filename
cannot start with the letters “mm” or “bm” because these
are restricted by the management software.
Privilege Levels
Administrator and read-write.
Description
This command is used to create a copy of a master configuration file in the
file system of the management module. You might create a copy of a file
to maintain a history of the settings of the modules in the chassis or to
create a backup copy. For background information on the master
configuration files, refer to Chapter 8, “Configuration File Commands” on
page 145.
Review the following before copying a master configuration file:
ˆ
This command is primarily intended for creating copies of master
configuration files on management modules. This command can also
be used to create copies of auxiliary configuration files, but that should
never be necessary.
ˆ
The copy of the file must be stored in the file system of the same
module with the original file. To copy files between modules, refer to
“FILE UPLOAD” on page 194.
ˆ
The filename of the source file is case sensitive. To verify the spelling
and case of a file, use the FILE SHOW command. For instructions,
refer to “FILE SHOW” on page 191.
ˆ
You do not have to perform the CONFIG SAVE command after
copying a file.
Examples
This command creates a copy of the master configuration file
“master2a.cfg” on a management module in a chassis with the ID number
0. The copy is called “master2a_backup.cfg:”
file copy srcfile=system://0/m/master2a.cfg
dstfile=system://0/m/master2a_backup.cfg
174
AT-S85 and AT-S97 Management Software User’s Guide
This command creates a copy of the master configuration file “mc 11a.cfg”
on a management module in a chassis assigned the ID 0. The copy will be
titled “mc 22 traffic.cfg:”
file copy srcfile=system://0/m/"mc 11a.cfg"
dstfile=system://0/m/"mc 22 traffic.cfg"
Note
The next example copies an auxiliary configuration file on a media
converter module. This function should never be necessary.
This command creates a copy of the “BM.cfg” auxiliary configuration file on
a media converter module in slot 2 in a chassis with the ID number 0. The
copy is named “BM_backup.cfg:”
file copy srcfile=system://0/2/BM.cfg
dstfile=system://0/2/"BM_backup.cfg"
175
Chapter 9: File System Commands
FILE DELETE
Syntax
file delete filesystem=system://chassis/slot/filename.cfg
Parameter
system
Specifies the location of the file to delete. This parameter
has the following parts:
chassis
Specifies an ID number of a chassis. The
range is 0 to 31. For background
information, refer to “Chassis ID Numbers”
on page 25.
slot
Identifies a slot with a module containing the
file. For background information, refer to
“Slot Numbers and Letters” on page 26.
Possible values are:
filename.cfg
m
Identifies the AT-MCF2000M
Management Module.
1 or 2
Specifies a slot number of a
media converter module in the
AT-MCF2000 Chassis. The left
slot is 1 and the right slot is 2.
1 to 4
Specifies a slot number of a
media converter module in the
AT-MCF2300 Chassis. The slots
are number 1 (left) and 2 (right)
in the top row, and 3 (left) and 4
(right) in the bottom row.
Specifies the name of the configuration file
to delete. The filename is case sensitive and
must be enclosed in double quotes if it
contains a space. The asterisk (*) can be
used as a wildcard to delete files with similar
names.
To view the ID and slot numbers of a chassis, refer to
“SYSTEM SHOW CHASSIS” on page 99 or “SYSTEM
SHOW CLUSTER” on page 101. To view the filenames in
the file system on a module, refer to “FILE SHOW” on
page 191.
176
AT-S85 and AT-S97 Management Software User’s Guide
Privilege Levels
Administrator and read-write.
Description
This command is used to delete unnecessary or obsolete files from the file
systems of the management module and the media converter modules.
For background information on configuration files, refer to Chapter 8,
“Configuration File Commands” on page 145.
Here are the guidelines to using this command:
ˆ
Allied Telesis does not recommend deleting the management module’s
active master configuration file. If you do delete the file, you should
afterwards specify a new active master configuration file with the
CONFIG SET command. For further information, refer to “CONFIG
SET” on page 164.
ˆ
Deleting a media converter’s configuration file (for example,
BM_00_01.cfg) from the file system of the management module does
not affect the operation of the media converter module or the
management module.
ˆ
Deleting a configuration file (for example, BM.cfg) from a media
converter’s file system is not recommended. Deleting the file does not
affect the operation of the module, except if you remove the module
and install it into a different slot. In the latter scenario, the module uses
its default values or the values provided by the management module.
ˆ
The filename is case sensitive. To verify the spelling and case of a
filename, use the FILE SHOW command. For instructions, refer to
“FILE SHOW” on page 191.
ˆ
You do not have to perform the CONFIG SAVE command after
deleting a file.
Examples
This command deletes the master configuration file “unit2a.cfg” from a
management module in a chassis with an ID number of 0:
file delete filesystem=system://0/m/unit2a.cfg
This command deletes the master configuration file “unit14ab.cfg” from a
management module in a chassis with an ID number of 0:
file delete filesystem=system://0/m/unit14ab.cfg
This command deletes all the configuration files starting with “BM” from
management module in a chassis with an ID number of 0:
file delete filesystem=system://0/m/BM*.cfg
177
Chapter 9: File System Commands
This command deletes the configuration file “BM.cfg” from the media
converter module in slot 2 in a chassis with an ID number of 0:
file delete filesystem=system://0/2/BM.cfg”
This command deletes all the configuration files starting with “BM” from a
media converter module in slot 2 in a chassis with an ID number of 0:
file delete filesystem=system://0/2/BM*.cfg
178
AT-S85 and AT-S97 Management Software User’s Guide
FILE DOWNLOAD
Syntax 1: Downloading the AT-S85 and AT-S97 Boot Loaders
file download srcfile=tftp://ipaddress/filename.bin
dstfile=system://chassis/slot/bootblock
Syntax 2: Downloading the AT-S85 and AT-S97 Management
Software (Image Files)
file download srcfile=tftp://ipaddress/filename.img
dstfile=system://chassis/slot/appblock
Syntax 3: Downloading Master Configuration Files
file download srcfile=tftp://ipaddress/filename.cfg
dstfile=system://chassis/slot/filename.cfg
Syntax 4: Downloading Configuration Files from a Management
Module to a Media Converter Module
file download srcfile=system://chassis/m/filename.cfg
dstfile=system://chassis/slot/filename.cfg
Parameters
srcfile=tftp
Specifies the IP address of the TFTP server and the name
of the file to download to a module. This parameter has the
following parts:
ipaddress
Specifies an IP address of a TFTP server.
filename
Specifies the name of the file on the TFTP
server to download onto the management
module or the media converter module.
Filenames with spaces must be enclosed in
double quotes. The filename extension must
be “.BIN” for the boot loader, “.IMG” for the
management software, and “.CFG” for a
configuration file.
dstfile=system
Specifies the destination chassis and module for the file.
This parameter has the following parts:
chassis
Specifies an ID number of a chassis. The
range is 0 to 31. To indicate all of the
chassis in a stack, enter an asterisk (*). For
background information, refer to “Chassis ID
Numbers” on page 25.
179
Chapter 9: File System Commands
slot
Identifies the slot number of a module. The
possible values are:
* (asterisk)
Indicates all of the slots in a
chassis.
m
Identifies the management
module slot.
1 or 2
Specifies a slot number of a
media converter module in the
AT-MCF2000 Chassis. The left
slot is 1 and the right slot is 2.
1 to 4
Specifies a slot number of a
media converter module in the
AT-MCF2300 Chassis. The slots
are number 1 (left) and 2 (right)
in the top row, and 3 (left) and 4
(right) in the bottom row.
bootblock
Designates the area of flash memory
reserved for the AT-S85 and AT-S97 boot
loader files.
appblock
Designates the area of flash memory
reserved for the AT-S85 and AT-S97
Management Software.
filename.cfg
Specifies a name for a master configuration
file. The file is assigned this name when it is
stored in the file system in a management
module after being downloaded from a
TFTP server. The name can be up to 15
alphanumeric characters, not including the
extension. Names with spaces are
permitted, but must be enclosed in double
quotes. The filename must include the
“.CFG” extension.
To view the ID and slot numbers of a chassis, refer to
“SYSTEM SHOW CHASSIS” on page 99 or “SYSTEM
SHOW CLUSTER” on page 101.
Privilege Levels
Administrator and read-write.
180
AT-S85 and AT-S97 Management Software User’s Guide
General Description
This command is used to download new versions of the AT-S85 and
AT-S97 boot loaders and management software to the management and
media converter modules in a chassis from a TFTP server. Allied Telesis
may post new versions of these files on our web site so our customers can
update their equipment with the latest files.
You can also use this command to download master configuration files
that you edited at your management workstation to the management
module.
To download a bootloader or image file onto all of the media converter
modules in a system, use the FILE FASTDOWNLOAD command. See
“FILE FASTDOWNLOAD” on page 186.
Description of Syntax 1
This command is used to download new versions of the boot loader files to
the management modules and the media converter modules from a TFTP
server. The boot loader is part of the operating system of a module.
There are different boot loaders for the different types of modules. The
AT-MCF2000M Management Module uses the AT-S97 boot loader and
the media converter modules the AT-S85 boot loader. The boot loader
files are identified by their “.BIN” filename extension and the “S85” and
“S97” in the filenames.
A boot loader must be stored on a module in an area of memory referred
to as BOOTBLOCK. This section of memory is separate from the file
system and it cannot be displayed with the FILE SHOW command. When
you enter the FILE DOWNLOAD command, you must specify
BOOTBLOCK as the destination. If you specify a filename as the
destination, the command stores the file in the file system of the module.
This is an inappropriate destination for a boot loader. (If you do
inadvertently download a boot loader file into the file system of a module,
you can delete it with the FILE DELETE command. For instructions, refer
to “FILE DELETE” on page 176.)
After receiving a new boot loader, a module tests the file before writing it to
the BOOTBLOCK area of flash memory to determine whether the file is
appropriate for its module type. If the file type is correct, it writes the file to
the BOOTAPP section. If it is not, it discards the file. This protects the
module from installing the wrong boot loader.
This command has the following guidelines:
ˆ
The filename extension of the source file must be “.BIN” and the
destination must be BOOTBLOCK.
ˆ
When upgrading both the boot loader and the management software
on the modules, you should download the new boot loader file first.
181
Chapter 9: File System Commands
Since this command uses the TFTP client on the management module,
Allied Telesis recommends reviewing the information in “Guidelines to
Using the TFTP Client” on page 171 prior to using the command.
Note
A management module resets after receiving a new bootloader. The
module is unresponsive to commands for approximately one minute
while it initializes its AT-S97 Management Software.
Note
After a media converter module receives a new bootloader, it resets
and immediately resumes forwarding network traffic through its ports
and channels using the default settings while it initializes the AT-S85
Management Software, a process that takes approximately one
minute to complete. The module is unresponsive to management
commands during the initialization process. At the completion of the
process, the module configures its ports and channels according to
the settings in the active master configuration file on the
management module.
Description of Syntax 2
This command performs much the same function as syntax 1. But rather
than downloading a boot loader file, it downloads a new version of the
management software to a module. The management software comes in
two versions, one for the management module, the AT-S97 Management
Software, and another for the media converter modules, the AT-S85
Management Software. A management program file can be identified by
the extension “.IMG” and the “S85” or S97” in its filename.
The management software is stored on a module in a special area of
memory referred to as APPBLOCK. This must be the destination of the
command when downloading the software.
Just as it does with a boot loader file, a module tests the file before it
writes it to the APPBLOCK section of flash memory. Only after the module
has verified that it is the correct file for its type of module does it write the
file to memory. This protects the module from installing the wrong
management software.
Note
A management module resets after receiving a new version of the
AT-S97 Management Software. It is unresponsive to commands for
approximately one minute while it initializes the new management
software.
182
AT-S85 and AT-S97 Management Software User’s Guide
Note
A media converter module resets after receiving a new version of
the AT-S85 Management Software. It immediately resumes
forwarding network traffic through its ports and channels using its
default settings while it initializes the new software. This process
takes approximately one minute to complete. The module is
unresponsive to management commands during the initialization
process. At the completion of the process, the module configures its
ports and channels according to the settings in either its own
auxiliary configuration file or the active master configuration file on
the management module, depending on the module’s overwrite
setting.
Description of Syntax 3
This command syntax is used to download a master configuration file from
a TFTP server to the file system of a management module. You might use
this command after editing a configuration file at your workstation or when
transferring a master configuration file from another chassis.
If, after downloading a new or edited master configuration file onto a
management module, you want to configure the modules using the file,
there are several additional commands you have to perform. First, you
must designate the file as the active configuration file for the management
module with the CONFIG SET command. Second, you must issue the
CONFIG RUN command so that the modules configure themselves
according to the commands in the file. For information, refer to Chapter 8,
“Configuration File Commands” on page 145.
Description of Syntax 4
This syntax is reserved for future versions of the management software.
Examples of Downloading the AT-S85 and AT-S97 Boot Loaders
This command downloads a new version of the AT-S85 boot loader onto
all of the media converter modules in a chassis. The IP address of the
TFTP server is 150.24.44.65 and the name of the file on the TFTP server
is “ats85.bin”:
file download srcfile=tftp://150.24.44.65/ats85.bin
dstfile=system://*/*/bootblock
Note
The above example is the preferred command for upgrading the
boot loader on the media converter modules in a chassis.
Downloading a new boot loader onto some but not all of the media
converter modules may result in compatibility problems.
183
Chapter 9: File System Commands
Since the slots are indicated with the wildcard “*”, all of the modules,
including the management module, receive the file. However, since the
AT-S85 boot loader is intended for the media converter modules, the
management module will discard the file and generate an error message,
which can be ignored.
This command downloads a new version of the AT-S97 boot loader onto a
management module. The IP address of the TFTP server is
162.101.11.12 and the name of the file is “ats97.bin”:
file download srcfile=tftp://162.101.1.12/ats97.bin
dstfile=system://*/m/bootblock
Note
The above example is the preferred command for upgrading the
boot loader on the management module.
This command downloads a new version of the AT-S85 boot loader onto
the media converter module in slot 1 in the chassis with an ID of 0. The IP
address of the TFTP server is 149.72.23.5 and the name of the file is
“ats85.bin”:
file download srcfile=tftp://149.72.23.5/ats85.bin
dstfile=system://0/1/bootblock
Examples of Downloading the AT-S85 and AT-S97 Management
Software
This command downloads a new version of the AT-S85 Management
Software onto all of the media converter modules in a chassis. The IP
address of the TFTP server is 150.24.44.65 and the name of the file is
“ats85.img”:
file download srcfile=tftp://150.24.44.65/ats85.img
dstfile=system://*/*/appblock
The asterisk is used to indicate all slots in the chassis which means the
management module receives the file as well. Since the AT-S85
Management Software is intended for media converter modules, it will
discard the file and generate an error message. You can ignore the
message.
Note
The above example is the preferred command for upgrading the
management software on the media converter modules in a chassis.
Downloading management software onto some but not all of the
modules of a chassis may cause compatibility problems.
184
AT-S85 and AT-S97 Management Software User’s Guide
This command downloads a new version of the AT-S97 Management
Software onto the AT-MCF2000M Management Module in a chassis. The
name of the file is “ats97.img:”
file download srcfile=tftp://149.72.23.5/ats97.img
dstfile=system://*/m/appblock
This command downloads a new version of the AT-S85 Management
Software onto the media converter module in slot 1 of a chassis with ID of
0. The IP address of the TFTP server is 150.24.44.65 and the name of the
file is “ats85.img:”
file download srcfile=tftp://150.24.44.65/ats85.img
dstfile=system://0/1/appblock
Example of Downloading a Master Configuration File
This command downloads the master configuration file “mc2000_22a.cfg”
onto a management module from a TFTP server. The file is renamed
“mcf2000 unit5a.cfg” in the file system of the module. The ID number of
the chassis is 0:
file download srcfile=tftp://150.76.8.124/mc2000_22a.cfg
dstfile=system://0/m/"mcf2000 unit5a.cfg"
185
Chapter 9: File System Commands
FILE FASTDOWNLOAD
Syntax 1 - AT-S85 Management Software
file fastdownload appblock srcfile=tftp://ipaddress/
filename.img
file fastdownload appblock srcfile=xmodem://filename.img
Syntax 2 - Bootloader
file fastdownload bootblock srcfile=tftp://ipaddress/
filename.bin
file fastdownload bootblock srcfile=xmodem://filename.bin
Parameters
bootblock
Designates the area of flash memory reserved for the
AT-S85 boot loader files on the media converter modules.
appblock
Designates the area of flash memory reserved for the
AT-S85 Management Software on the media converter
modules.
ipaddress
Specifies an IP address of a TFTP server.
filename
Specifies a name of a bootloader file or the AT-S85
Management Software to download to the media converter
modules using TFTP or XMODEM. Filenames with spaces
must be enclosed in double quotes. The filename
extensions must be “.BIN” for bootloader files and “.IMG”
for the management software.
Privilege Levels
Administrator and read-write.
General Description
If you need to update the bootloader files or the management software
image files on all of the media converter modules in a chassis or stack,
you can use this command instead of the FILE DOWNLOAD command.
One of the advantages of this command is speed, just as its name implies.
With this command, all of the media converter modules are updated
simultaneously by the management module, rather than sequentially, as
with the FILE DOWNLOAD command.
186
AT-S85 and AT-S97 Management Software User’s Guide
Another advantage of this command is that you can use either TFTP or
XMODEM to download the files. In contrast, the FILE DOWNLOAD
command supports just TFTP.
There are two command syntaxes for the two types of files you’re likely to
download to the media converter modules. Syntax 1 is used to download
new versions of the AT-S85 Management Software and Syntax 2 is for
new versions of the bootloader files.
Obviously, if you’re only interested in updating the files on selected media
converter modules, you should use the FILE DOWNLOAD command
instead, because it lets you specify the modules you want to update.
You cannot use this command to update the files on the management
module or to download configuration files to a module. For these functions,
use the FILE DOWNLOAD command.
Examples
This command downloads a new version of the AT-S85 Management
Software from a TFTP server with the IP address 192.100.10.1 to all of the
media converter modules. The name of the file is “ATS85_MCF2000.IMG:”
file fastdownload appblock srcfile=tftp://192.100.10.1/
ats85_mcf2000.img
This command uses XMODEM to download a new version of the AT-S85
Management Software to the media converter modules. The name of the
file is “ATS85.IMG:”
file fastdownload appblock srcfile=xmodem:ats85.img
This command downloads to all of the media converter modules the new
bootloader file “ATS85_BOOTLOADER.BIN” from a TFTP server with the
IP address 192.100.10.1:
file fastdownload bootblock srcfile=tftp://192.100.10.1/
ats85_bootloader.bin
This command downloads the new bootloader file “ATS85_BLDR.BIN”
using XMODEM:
file fastdownload bootblock srcfile=xmodem://ats85_bldr.bin
187
Chapter 9: File System Commands
FILE RENAME
Syntax
file rename srcfile=system://chassis/slot/filename
dstfile=system://chassis/slot/filename
Parameters
srcfile=system
Specifies the location and name of the master configuration
file to rename. This parameter has the following parts:
chassis
Specifies an ID number of a chassis. The
range is 0 or 31.
slot
Specifies a slot number of a module that has
the file you want to rename. Possible values
are:
filename
m
Identifies the management
module slot.
1 or 2
Specifies a slot number of a
media converter module. In the
AT-MCF2000 Chassis, the left
slot is 1 and the right slot is 2.
Specifies the name of the file to rename. The
filename must include the “.CFG extension.
The name is case sensitive and must be
enclosed in double quotes if it has spaces.
To verify the spelling and case of a file in a
modules file system, use the FILE SHOW
command. For instructions, refer to “FILE
SHOW” on page 191.
dstfile=system
Specifies a new name for the master configuration file. The
destination must be the same chassis and slot location as
the source. The name can be up to 15 alphanumeric
characters, not including the extension. Spaces are
allowed, but a name with spaces must be enclosed in
double quotes. The filename must be unique in the file
system of the module and include the “.CFG” extension.
The filename cannot start with the letters “mm” or “bm”
because these letters are reserved by the management
software.
188
AT-S85 and AT-S97 Management Software User’s Guide
Privilege Levels
Administrator and read-write.
Description
This command is used to rename the master configuration files on a
management module. Observe the following guidelines when using this
command:
ˆ
If you rename the active master configuration file, the management
software recreates it the next time you issue the CONFIG SAVE
command. To view the name of the active master configuration file,
refer to “CONFIG SHOW” on page 166.
ˆ
Although you can use the command to rename auxiliary configuration
files (for example, BM.cfg or MM.cfg) in the file systems of the
management and media converter modules, Allied Telesis does not
recommend it. You should limit the use of this command to renaming
the master configuration file.
ˆ
A filename cannot start with the letters “MM” or “BM.”
ˆ
You do not have to perform the CONFIG SAVE command after
renaming a file.
For information on configuration files, refer to Chapter 8, “Configuration
File Commands” on page 145.
Examples
This command renames the master configuration file “unit12a.cfg” on the
management module to “u2 a7.cfg.” The chassis ID number is 0:
file rename srcfile=system://0/m/unit12a.cfg
dstfile=system://0/m/"u2 a7.cfg"
This command renames the master configuration file “mcf 2a.cfg” on the
management module to “mcf aba traffic.cfg.” The chassis ID number is 0:
file rename srcfile=system://0/m/"mcf 2a.cfg"
dstfile=system://0/m/"mcf aba traffic.cfg"
Note
The following examples illustrate how to rename an auxiliary
configuration file. This function should never be necessary.
This command renames the media converter configuration file
“BM_0_1.cfg” to “BM_0_1 backup.cfg” in the file system on the
management module which has a chassis ID number of 0:
189
Chapter 9: File System Commands
file rename srcfile=system://0/m/BM_0_1.cfg
dstfile=system://0/m/"BM_0_1 backup.cfg"
This command renames the configuration file “BM.cfg” to “BM_2.cfg” in
the file system of a media converter module in slot 1 of a chassis with an
ID
of 0:
file rename srcfile=system://0/1/BM.cfg
dstfile=system://0/1/BM_2.cfg
190
AT-S85 and AT-S97 Management Software User’s Guide
FILE SHOW
Syntax
file show filesystem=system://chassis/slot/filename
Parameters
system
Specifies the chassis and module with the file system to
display. This parameter has the following parts:
chassis
Specifies the ID number of the chassis with
the file. The value of the ID number is 0 or
31.
slot
Specifies the ID number or letter of the slot
with the module. Possible values are:
filename
m
Identifies the slot with the
AT-MCF2000M Management
Module.
1 or 2
Specifies a slot with a media
converter module. In the
AT-MCF2000 Chassis, the left
slot is 1 and the right slot is 2.
Specifies the filenames to view. The
filename is case sensitive. You can use the
asterisk (*) as a wildcard.
To view the ID and slot numbers of the devices in a chassis
or stack, refer to “SYSTEM SHOW CHASSIS” on page 99
or “SYSTEM SHOW CLUSTER” on page 101.
Privilege Levels
Administrator, read-write, and read-only.
Description
This command displays the names of the files in the file system on a
management module. An example is shown in Figure 39. You might view
the file system to verify the spelling and case of the filename of a master
configuration file prior to designating it as the active master configuration
file or uploading it to a TFTP server.
191
Chapter 9: File System Commands
Module 0/M File System:
-rw-r--r-1
0
-rw-r--r-1
0
-rw-r--r-1
0
-rw-r--r-1
0
-rw-r--r-1
0
0
0
0
0
0
2747
2652
402
849
5612
File
Size
Apr
Apr
Apr
Apr
Apr
12
12
12
12
12
14:52
14:52
14:52
14:52
14:52
BM_0_1.cfg
BM_0_2.cfg
file.inf
MM.cfg
Chassis12a.cfg
Date and
Time
Filename
Figure 39. FILE SHOW Command
The first four columns can be ignored. The remaining columns are defined
here:
ˆ
File size - The size of the file in bytes.
ˆ
Date and Time - The date and time when the file was created or last
modified.
ˆ
Filename - The name of the file.
This command can also display the contents of a file system on a media
converter module, but you should never need to do that. For information
on configuration files, refer to “Overview” on page 146.
Examples
This command displays all the filenames in the file system on the
management module in a chassis with an ID number of 0:
file show filesystem=system://0/m/*.*
This command displays the names of just the configuration files on a
management module in a chassis with an ID number of 0:
file show filesystem=system://0/m/*.cfg
This command displays the names of the configuration files starting with
“Ch” on a management module in chassis with an ID number of 0:
file show filesystem=system://0/m/Ch*.cfg
This command displays the names of the configuration files on the
management module in a chassis with an ID number of 0:
file show filesystem=system://0/m/*.cfg
192
AT-S85 and AT-S97 Management Software User’s Guide
Note
The following examples illustrate how to display the files in the file
system on a media converter module. This function should never be
necessary.
This command displays all the filenames on a media converter module in
slot 2 in a chassis with an ID number of 0:
file show filesystem=system://0/2/*.*
This command displays the filenames of just the configuration files on a
media converter module in slot 1 in a chassis with an ID number of 0:
file show filesystem=system://0/1/*.cfg
193
Chapter 9: File System Commands
FILE UPLOAD
Syntax 1: Uploading a Configuration File to a TFTP Server
file upload srcfile=system://chassis/slot/filename.cfg
dstfile=tftp://ipaddress/filename.cfg
Syntax 2: Uploading a Configuration File from a Media Converter
Module to a Management Module
file upload srcfile=system://chassis/slot/filename.cfg
dstfile=system://chassis/m/filename.cfg
Parameters
srcfile=system
Specifies the location and the name of the file to upload.
This parameter has the following parts:
chassis
Specifies the ID number of the chassis with
the file. The value of the ID number is 0
or 31. For background information, refer to
“Chassis ID Numbers” on page 25.
slot
Identifies a chassis slot. The possible values
are:
filename
194
m
Identifies the slot with the
AT-MCF2000M Management
Module.
1 or 2
Specifies a media converter slot
in the AT-MCF2000 Chassis.
The left slot is 1 and the right slot
is 2.
1 to 4
Specifies a media converter slot
in the AT-MCF2300 Chassis.
The slots are number 1 (left) and
2 (right) in the top row, and 3
(left) and 4 (right) in the bottom
row.
Specifies the name of the file to upload. A
filename with a space must be enclosed in
double quotes. The filename extension must
be “.CFG.” The filename is case sensitive.
AT-S85 and AT-S97 Management Software User’s Guide
To view the ID and slot numbers of the devices in a chassis
or stack, refer to “SYSTEM SHOW CHASSIS” on page 99
or “SYSTEM SHOW CLUSTER” on page 101. To view the
files in a file system, refer to “FILE SHOW” on page 191.
dstfile=tftp
Specifies the TFTP server to receive the file. This
parameter is used to upload a configuration file from a
management or media converter module to a TFTP server.
This parameter has the following parts:
ipaddress
Specifies an IP address of a TFTP server.
filename.cfg
Specifies a name for the file when stored to
the FTP server. Enclose the filename in
double quotes if it contains a space. The
filename extension must be “.CFG.”
dstfile=system
Specifies the module to receive the file when transferring a
configuration file between modules in a chassis. This
parameter has the following parts:
chassis
Specifies the ID number of the chassis with
the file. The value of the ID number is 0
or 31. For background information, refer to
“Chassis ID Numbers” on page 25.
slot
Identifies the slot with the management
module to receive the file. The only accepted
value for this parameter is:
m
Identifies the management slot
with the AT-MCF2000M
Management Module.
Privilege Levels
Administrator and read-write.
Description of Syntax 1
This command is used to upload configuration files from a management
module or media converter module to an TFTP server. Typically, this
command is used to upload a master configuration file from a
management module prior to editing it at your workstation or transferring it
to another management module in another chassis.
Although this command can also be used to upload a media converter’s
auxiliary configuration file from the file system of a management module or
media converter module, Allied Telesis recommends against this. Editing
or transferring auxiliary configuration files serves no purpose since the
195
Chapter 9: File System Commands
settings are overwritten by the master configuration file on the
management module after the file is installed on a media converter
module. For further information on configuration files, refer to “Overview”
on page 146.
Description of Syntax 2
This command syntax is reserved for future versions of the management
software.
Examples of Uploading a Configuration File to a TFTP Server
This command uploads the master configuration file “traffic_n2.cfg” from a
management module to a TFTP server with the IP address of
150.24.44.65. The chassis has the ID number 0:
file upload srcfile=system://0/m/traffic_n2.cfg
dstfile=tftp://150.24.44.65/traffic_n2.cfg
This command uploads the master configuration file “mic traf ata.cfg” from
the management module of a chassis with an ID number of 0. The IP
address of the server is 149.72.23.5 and the name of the file is changed to
“mic traf bc.cfg on the TFTP server:
file upload srcfile=system://0/m/"mic traf ata.cfg"
dstfile=tftp://149.72.23.5/”mic traf bc.cfg”
Note
The following example shows how to upload an auxiliary
configuration file from a media converter module. This function
should never be necessary.
This command uploads the auxiliary configuration file “BM.cfg” from a
media converter module in slot 1 of a chassis with an ID number of 0:
file upload srcfile=system://0/1/BM.cfg
dstfile=tftp://150.24.44.65/BM.cfg
196
Chapter 10
Telnet Server Commands
This chapter contains the following sections:
ˆ
“Overview” on page 198
ˆ
“TELNET DISABLE” on page 200
ˆ
“TELNET ENABLE” on page 201
ˆ
“TELNET SHOW” on page 202
Note
Remember to save your parameter changes in the active master
configuration file with the CONFIG SAVE command. For information,
refer to “Saving Your Configuration Changes” on page 23 or
“CONFIG SAVE” on page 161.
197
Chapter 10: Telnet Server Commands
Overview
The commands in this chapter are used to control the management
module’s Telnet application protocol server, used for remote management
of the chassis from a Telnet client on your network. The commands
TELNET ENABLE and TELNET DISABLE are used to enable and disable
the server, while the TELNET SHOW command is used to display the
current status of the server. The server’s default setting is disabled.
To start a remote Telnet management session on the management
module, enter the IP address of the management module in the Telnet
client at your remote management workstation. For further instructions,
refer to “Starting a Remote Telnet or Secure Shell Management Session”
on page 20.
The Telnet server uses protocol port 23. You cannot change this value.
Telnet Server
Guidelines
Command
Summary
Here are the guidelines to managing a chassis remotely with a Telnet
client:
ˆ
The management module must have an IP configuration. For
instructions, refer to Chapter 3, “IP Configuration Commands” on page
47.
ˆ
The 10/100/1000Base-T Management port on the management
module must be connected to a network device, such as a Fast
Ethernet or Gigabit switch. Remote Telnet management sessions are
conducted through this port.
ˆ
The remote Telnet client must be a member of the same network as
the management module or have access to it through Layer 3 routing
devices.
ˆ
If the management module and remote Telnet client are on different
networks, the IP configuration on the management module must
include a default gateway that specifies the IP address of the first hop
to reaching the workstation. For instructions, refer to Chapter 3, “IP
Configuration Commands” on page 47.
ˆ
The management module can support up to 20 Telnet and 20 SSH
concurrent remote management sessions.
Table 21 summarizes the Telnet server commands.
Table 21. Telnet Server Commands
Command
TELNET DISABLE on
page 200
198
Description
Deactivates the Telnet application
protocol server.
AT-S85 and AT-S97 Management Software User’s Guide
Table 21. Telnet Server Commands (Continued)
Command
Description
TELNET ENABLE on
page 201
Activates the Telnet application
protocol server.
TELNET SHOW on page 202
Displays the status of the Telnet
server.
199
Chapter 10: Telnet Server Commands
TELNET DISABLE
Syntax
telnet disable
Parameters
None.
Privilege Levels
Administrator and read-write.
Description
This command is used to disable the Telnet server on the management
module. This is the server’s default setting. When the server is disabled,
you can not manage the unit remotely with a Telnet client. You should
leave the server disabled if you will not be managing the unit with a Telnet
client, to protect the management module from unauthorized access.
Note
If you disable the server during a remote Telnet management
session, the session is automatically logged out. To continue
managing the unit, start a local management session on the unit.
Example
telnet disable
200
AT-S85 and AT-S97 Management Software User’s Guide
TELNET ENABLE
Syntax
telnet enable
Parameters
None.
Privilege Levels
Administrator and read-write.
Description
This command is used to activate the Telnet server on the management
module for remote Telnet management of the chassis. The default setting
for the server is disabled.
Note
Review “Telnet Server Guidelines” on page 198 for the
preconditions for remote Telnet management. For instructions on
starting a remote session, refer to “Starting a Remote Telnet or
Secure Shell Management Session” on page 20.
Example
telnet enable
201
Chapter 10: Telnet Server Commands
TELNET SHOW
Syntax
telnet show
Parameters
None.
Privilege Levels
Administrator, read-write, and read-only.
Description
This command is used to display the status of the Telnet server on the
management module. The status of the server can be either Enable or
Disable. If the status is Enable, the management module can be managed
remotely with a Telnet client on your network. If the status is Disable, the
management module cannot be remotely managed. An example is shown
in Figure 40.
Telnet Status ........ Enable
Figure 40. TELNET SHOW Command
Example
telnet show
202
Chapter 11
Simple Network Management Protocol
(SNMP) Commands
This chapter contains the following sections:
ˆ
“Overview” on page 204
ˆ
“SNMP SET” on page 206
ˆ
“SNMP SHOW” on page 208
Note
Remember to save your parameter changes in the active master
configuration file with the CONFIG SAVE command. For information,
refer to “Saving Your Configuration Changes” on page 23 or
“CONFIG SAVE” on page 161.
203
Chapter 11: Simple Network Management Protocol (SNMP) Commands
Overview
The commands in this chapter are used to set the three Get, Set and Trap
community strings for Simple Network Management Protocol (SNMP).
These strings can be used to manage the media converter with an
SNMPv1 or SNMPv2c application and for trap verification.
The commands here are also used to set the IP addresses of up to four
trap receivers. Traps are signals sent to management workstations by the
unit to indicate the occurrences of specific operating events on the device,
and are commonly used to monitor the activities of the unit.
SNMP Guidelines
Trap Events
204
Here are the guidelines for remote SNMPv1 and SNMPv2c management:
ˆ
The management module must have an IP configuration. For
instructions, refer to Chapter 3, “IP Configuration Commands” on page
47.
ˆ
The 10/100/1000Base-T Management port on the management
module must be connected to a network device, such as a Fast
Ethernet or Gigabit switch. Remote SNMP management sessions are
conducted through that port.
ˆ
The remote workstation with the SNMP program must be a member of
the same network as the management module or have access to it
through Layer 3 routing devices.
ˆ
If the management module and remote workstation are on different
networks, the IP configuration on the management module must
include a default gateway that specifies the IP address of the first hop
to reaching the workstation. For instructions, refer to Chapter 3, “IP
Configuration Commands” on page 47.
ˆ
You must load the Allied Telesis private MIBs into your SNMP program
on your workstation. The MIBs are available from the Allied Telesis
web site at www.alliedtelesis.com.
Activities that generate SNMP traps are listed below:
ˆ
Module has been installed or removed
ˆ
Port link status is offline or online
ˆ
Port link status is RX (receive) SML or TX (transmit) SML
ˆ
Port operational mode is changed to Missing Link or SML
ˆ
Port operational mode is changed to OAM Bypass, OAM visible, or link
test
ˆ
TFTP session is opened or closed
ˆ
XMODEM session is opened or closed
ˆ
Telnet session is opened or closed
AT-S85 and AT-S97 Management Software User’s Guide
ˆ
Telnet server is enabled or disabled
ˆ
SSH session is opened or closed
ˆ
SSH session is enabled or disabled
ˆ
Warm or cold boot of a media converter module
ˆ
Management stacking port is up or down
ˆ
A module was acquired by or released by the chassis management
ˆ
Login authentication failure
ˆ
Fan A failure or recovery on either power module or AT-MCF2KFAN
fan
ˆ
Fan B failure or recovery on either power module or AT-MCF2KFAN
fan
ˆ
Power failure or recovery on a power module
ˆ
Chassis has been reset
ˆ
Module has been reset
ˆ
Low battery or recovery from low battery
ˆ
Management module has overwritten media converter module
configuration
ˆ
Media converter module has overwritten management module
configuration
Trap receivers are the devices, typically management workstations or
servers, that you want to receive the traps sent by the unit. You specify the
trap receivers by their IP addresses.
Command
Summary
Table 22 summarizes the SNMP commands.
Table 22. SNMP Commands
Command
Description
“SNMP SET” on page 206
Sets the SNMPv1 and SNMPv2c
community strings and the IP
addresses of the trap receivers.
SNMP SHOW on page 208
Displays the SNMPv1 and
SNMPv2c community strings and
the IP addresses of the trap
receivers.
205
Chapter 11: Simple Network Management Protocol (SNMP) Commands
SNMP SET
Syntax
snmp set mgrip1=ipaddress mgrip2=ipaddress mgrip3=ipaddress
mgrip4=ipaddress Get-community=string Set-community=string
Trap-community=string
Parameters
mgrip1 - mrip4
Sets the IP addresses of up to four trap receivers.
The IP addresses have to be entered in the
following format: xxx.xxx.xxx.xxx To replace a
current value without entering a new value, enter
the default value, 0.0.0.0. This parameter is
optional.
Get-community
Sets the get community string. The string can be up
to 14 alphanumeric characters. The string is case
sensitive and can contain special characters,
including spaces. However, a community string with
spaces must be enclosed in double quotes (“ “). The
default value is “public.”
Set-community
Sets the set community string. The string can be up
to 14 alphanumeric characters. The string is case
sensitive and can contain special characters,
including spaces. However, a community string with
spaces must be enclosed in double quotes (“ “). The
default value is “private.”
Trap-community
Sets the trap community string. The string can be up
to 14 alphanumeric characters. The string is case
sensitive and can contain special characters,
including spaces. However, a community string with
spaces must be enclosed in double quotes (“ “). The
default value is “public.”
Privilege Levels
Administrator and read-write
Description
This command is used to set the SNMPv1 and SNMPv2c community
strings and to specify the IP addresses of up to four trap receivers.
206
AT-S85 and AT-S97 Management Software User’s Guide
Examples
This command changes the set community string to “snmpsecret1.”
snmp set set-community=snmpsecret1
This command changes the get and trap community strings to “mod1get”
and “mod1trap,” respectively:
snmp set get-community=mod1get trap-community=mod1trap
This command designates as trap receivers the IP addresses 168.12.1.1
and 168.12.1.12, assigning them to MGRIP1 and MGRIP2:
snmp set mgrip1=168.12.1.1 mgrip2=168.12.1.12
This command removes an IP address of a trap receiver from MGRIP4
without assigning a new value:
snmp set mgrip4=0.0.0.0
207
Chapter 11: Simple Network Management Protocol (SNMP) Commands
SNMP SHOW
Syntax
snmp show
Parameters
None.
Privilege Levels
Administrator, read-write and read-only
Description
This command is used to display the SNMPv1 and v2c community strings
and the IP addresses of the trap receivers. An example is shown in
Figure 41.
SNMP Information:
Get Community...............public
Set Community...............private
TrapCommunity...............public
Manager
Manager
Manager
Manager
1
2
3
4
IP
IP
IP
IP
address........0.0.0.0
address........0.0.0.0
address........0.0.0.0
address........0.0.0.0
Figure 41. SNMP SHOW Command
Example
snmp show
208
Chapter 12
Secure Shell Server (SSH) Commands
This chapter describes the Secure Shell Server (SSH) feature and
commands. This chapter contains the following sections:
ˆ
“Overview” on page 210
ˆ
“SSH DISABLE” on page 212
ˆ
“SSH ENABLE” on page 213
ˆ
“SSH SHOW” on page 214
Note
Remember to save your parameter changes in the active master
configuration file with the CONFIG SAVE command. For information,
refer to “Saving Your Configuration Changes” on page 23 or
“CONFIG SAVE” on page 161.
209
Chapter 12: Secure Shell Server (SSH) Commands
Overview
The AT-S97 Management Software has a Secure Shell (SSH) application
protocol server for remote management of the chassis with an SSH client.
Compared to remote Telnet management, this form of management is
more secure because it uses encryption during the management
sessions. During a remote Telnet management session, the payloads in
the packets exchanged between the management workstation and the
management module are sent in clear text, including the login user name
and password. This can leave the management module open to
unauthorized access if someone captures the management packets
during a remote Telnet management session. But with SSH, the payloads
in the packets are encrypted.
The SSH server uses protocol port 22. You cannot change this value.
The server supports SSH protocols 1 and 2. Supported Protocol 1 ciphers
include:
ˆ
Blowfish
ˆ
Triple Data Encryption Standard (3DES)
Supported Protocol 2 ciphers include:
ˆ
Blowfish
ˆ
Triple Data Encryption Standard (3DES)
ˆ
ARCFOUR
ˆ
128, 192, and 256-bit Advanced Encryption Standard (AES)
The two commands SSH ENABLE and SSH DISABLE enable and disable
the SSH server in the management software. The default setting for the
SSH server on the management module is disabled.
To start a remote SSH management session with the management
module, enter the IP address of the management module in the SSH client
at your remote management workstation. For further instructions, refer to
“Starting a Remote Telnet or Secure Shell Management Session” on
page 20.
SSH Server
Guidelines
Here are the guidelines for managing a chassis remotely with an SSH
client:
ˆ
210
The 10/100/1000Base-T Management port on the management
module must be connected to a network device, such as a Fast
Ethernet or Gigabit Ethernet switch. Remote SSH management
sessions are conducted through this port.
AT-S85 and AT-S97 Management Software User’s Guide
Command
Summary
ˆ
The management module must have an IP configuration. For
instructions, refer to Chapter 3, “IP Configuration Commands” on page
47.
ˆ
The remote SSH management workstation must be a member of the
same network as the management module or have access to it
through Layer 3 routing devices.
ˆ
If the management module and the remote SSH management
workstation are on different networks, the IP configuration on the
module must include a default gateway address specifying the IP
address of the routing interface of the first hop to reaching the
workstation. For instructions, refer to Chapter 3, “IP Configuration
Commands” on page 47.
ˆ
The management module can support up to 20 Telnet and 20 SSH
concurrent management sessions.
Table 23 summarizes the SSH server commands.
Table 23. Secure Shell Server Commands
Command
Description
SSH DISABLE on page 212
Deactivates the SSH application
protocol server.
SSH ENABLE on page 213
Activates the SSH application
protocol server.
SSH SHOW on page 214
Displays the current settings of the
SSH server.
211
Chapter 12: Secure Shell Server (SSH) Commands
SSH DISABLE
Syntax
ssh disable
Parameters
None.
Privilege Levels
Administrator and read-write
Description
This command is used to disable the SSH server on the management
module. This is the default setting for the server. When the server is
disabled, you can not manage the unit remotely from an SSH client. You
should leave the server disabled if you will not be managing the unit with
an SSH client, to protect the management module from unauthorized
access.
Note
If you disable the server during a remote SSH management session,
the session is automatically logged out. To continue managing the
unit, start a local management session on the unit or a remote
Telnet session.
Example
ssh disable
212
AT-S85 and AT-S97 Management Software User’s Guide
SSH ENABLE
Syntax
ssh enable
Parameters
None.
Privilege Levels
Administrator and read-write
Description
This command is used to activate the SSH server on the management
module for remote management with the SSH application protocol. The
default setting for the SSH server is disabled.
Note
Refer to “SSH Server Guidelines” on page 210 for the requirements
of remote SSH management. For instructions on how to start a
management session, refer to “Starting a Remote Telnet or Secure
Shell Management Session” on page 20.
Example
ssh enable
213
Chapter 12: Secure Shell Server (SSH) Commands
SSH SHOW
Syntax
ssh show
Parameters
None.
Privilege Levels
Administrator, read-write and read-only
Description
This command is used to display the current status of the SSH server on
the management module. An example is shown in Figure 42. The status of
the server can be either Enable or Disable. If the status is Enable, the
management module can be managed remotely with an SSH client on
your network. If the status is Disable, the management module can not be
remotely managed.
SSH Status ........ Enable
Figure 42. SSH SHOW Command
Example
ssh show
214
Chapter 13
Manager Account Commands
This chapter contains the following sections:
ˆ
“Overview” on page 216
ˆ
“USER ADD” on page 218
ˆ
“USER DELETE” on page 220
ˆ
“USER SET” on page 221
ˆ
“USER SHOW” on page 223
Note
Remember to save your parameter changes in the active master
configuration file with the CONFIG SAVE command. For information,
refer to “Saving Your Configuration Changes” on page 23 or
“CONFIG SAVE” on page 161.
215
Chapter 13: Manager Account Commands
Overview
The AT-S97 Management Software has one predefined manager account
with a privilege level of administrator. This account, with its login name of
“manager” and default password of “friend,” provides a network manager
with complete access to all of the commands.
The management module can support additional manager accounts, a
useful feature when more than one administrator manages a device.
Rather than having to share a login account, each administrator can be
given a separate account. The additional manager accounts can have a
privilege level of read, which allows a manager to view but not change the
settings, or read-write, which is nearly equivalent to the administrator
privilege level in the predefined account. The differences between the
predefined manager account and a privilege level of read-write are that
only the former can add, delete, and modify additional manager accounts,
clear the messages in the event log, and return the chassis to the default
settings.
Accounts are created with the USER ADD command, deleted and
modified with the USER DELETE and USER SET commands, and
displayed with the USER SHOW command.
Manager Account
Guidelines
Command
Summary
Here are the guidelines for adding manager accounts to the
AT-MCF2000M Management Module:
ˆ
The AT-MCF2000M Management Module supports up to ten read
accounts and ten read-write accounts in addition to the predefined
manager account.
ˆ
Only the predefined manager account can have the privilege level of
administrator.
ˆ
Only the predefined manager account with its privilege level of
administrator can add, delete, and modify user accounts, clear the
messages in the event log, and return the chassis to the default
settings.
ˆ
The manager accounts are self-contained on the management module
and do not use the RADIUS or TACACS+ authentication protocol.
Table 24 summarizes the manager account commands.
Table 24. Manager Account Commands
Command
216
Description
USER ADD on page 218
Adds a new manager account.
USER DELETE on page 220
Deletes a manager account.
AT-S85 and AT-S97 Management Software User’s Guide
Table 24. Manager Account Commands (Continued)
Command
Description
USER SET on page 221
Modifies the password and
privilege level of a manager
account.
USER SHOW on page 223
Displays the current manager
accounts.
217
Chapter 13: Manager Account Commands
USER ADD
Syntax
user add username=name privilege=read|readwrite
Parameters
username
Specifies a name between 1 and 16 alphanumeric
characters in length. The name is case sensitive. Special
characters are permitted with the exception of the question
mark (?) and quotation marks (“). However, to specify
spaces in a user name, you must enclose the name in
quotation marks.
privilege
Specifies the privilege level of the account. Options are:
read
Allows the account user to view but not change
the parameter settings of the modules.
readwrite Allows the account user to view and change the
parameter settings of the modules.
Privilege Level
Administrator
Description
This command is used to create new manager accounts on the
management module. For background information, refer to “Overview” on
page 216.
After you enter the command, you are prompted for the password for the
new account. A password can be from 1 to 16 alphanumeric characters
and is case sensitive. Spaces and special characters in a password are
not recommended. The management software prompts twice for the
password for verification. The password is stored in the active master
configuration file using MD5 encryption.
Examples
This command creates the new manager account “Smith” with the
privilege level of read-write. Prompts for the password for the new account
are displayed after the command is entered:
user add username=Smith privilege=readwrite
218
AT-S85 and AT-S97 Management Software User’s Guide
This command creates the new manager account “Eric Jones” with the
privilege level of read:
user add username="Eric Jones" privilege=read
This command creates the new manager account “** Marker” with the
privilege level of read-write:
user add username="** Marker" privilege=readwrite
219
Chapter 13: Manager Account Commands
USER DELETE
Syntax
user delete username=name
Parameters
username
Specifies the name of the manager account to be deleted
from the management module. Usernames are case
sensitive. Names with spaces must be enclosed in
quotation marks.
Privilege Levels
Administrator
Description
This command is used to delete manager accounts from the management
module. To view the manager accounts, use the USER SHOW command.
You cannot delete the predefined manager account.
Examples
This command deletes the manager account “Smith:”
user delete username=Smith
This command deletes the manager account “John Smith:”
user delete username="John Smith"
220
AT-S85 and AT-S97 Management Software User’s Guide
USER SET
Syntax
user set username=name password privilege=read|readwrite
Parameters
username
Specifies the name of the manager account to be modified.
Usernames are case sensitive. Names with spaces must be
enclosed in quotation marks.
password
Changes the password of the account. A prompt for the
new password is displayed after the command is entered. A
password can be up to 16 alphanumeric characters and is
case sensitive. Special characters, including spaces,
question marks, and quotation marks, are permitted.
privilege
Specifies the new privilege level for the manager account.
Options are:
read
Allows the account user to view but not change
the parameter settings of the modules.
readwrite Allows the account user to view and change the
parameter settings of the modules.
Privilege Levels
Administrator
Description
This command is used to modify the passwords or privilege levels of the
manager accounts. To view the manager accounts, use the USER SHOW
command. You can change the password but not the privilege level of the
predefined manager account.
Examples
This command changes the password of the predefined manager account:
user set username=manager password
This command changes the privilege level of the manager account “Smith”
to read-write:
user set username=Smith priviledge=readwrite
221
Chapter 13: Manager Account Commands
This command changes the password and privilege level of the “Tom
Adams” account:
user set username="Tom Adams" password priviledge=read
This command changes the password of the “Owen” account:
user set username=Owen password
222
AT-S85 and AT-S97 Management Software User’s Guide
USER SHOW
Syntax
user show
Parameters
None.
Privilege Levels
Administrator, read-write, and read-only.
Description
This command is used to display the manager accounts on the
AT-MCF2000M Management Module. An example of the information is
shown in Figure 43. The first entry in the table, “manager,” is the
predefined manager account. For background information, refer to
“Overview” on page 216.
Username
Privilege
-------------------------manager
administrator
Smith
read/write
Adams
read/write
Tim Johnson
read
Rob Johnson
read
Figure 43. USER SHOW Command
Example
user show
223
Chapter 13: Manager Account Commands
224
Chapter 14
Diagnostics Commands
This chapter contains the following sections:
ˆ
“Overview” on page 226
ˆ
“DIAGNOSTICS SHOW BOOTLOADER” on page 227
ˆ
“DIAGNOSTICS SHOW CHASSIS” on page 230
ˆ
“DIAGNOSTICS SHOW MODULE” on page 232
ˆ
“DIAGNOSTICS SHOW SOFTWARE” on page 235
225
Chapter 14: Diagnostics Commands
Overview
The diagnostics commands are used to display manufacturing information
which you may be asked to provide if you contact Allied Telesis Technical
Support for assistance. They do not test any of the components on the
modules in a chassis.
Command
Summary
226
Table 25 summarizes the diagnostics commands.
Table 25. Diagnostics Commands
Command
Description
“DIAGNOSTICS SHOW
BOOTLOADER” on page 227
Displays the version number of the
software bootloader.
DIAGNOSTICS SHOW
CHASSIS on page 230
Displays manufacturing
information about a module.
“DIAGNOSTICS SHOW
MODULE” on page 232
Displays manufacturing and
operating information about a
module.
“DIAGNOSTICS SHOW
SOFTWARE” on page 235
Displays the version number of the
software.
AT-S85 and AT-S97 Management Software User’s Guide
DIAGNOSTICS SHOW BOOTLOADER
Syntax
diagnostics show bootloader
Parameters
none
Privilege Levels
Administrator, read-write, and read-only.
Description
This command is used to display the version numbers of the bootloaders
on the management modules and the media converter modules. You may
need to provide this information if you contact Allied Telesis Technical
Support for assistance,. Figure 45 is an example of the DIAGNOSTIC
SHOW BOOTLOADER command.
227
Chapter 14: Diagnostics Commands
Chassis
Chassis
Chassis
MAC
Master
ID
Name
Type
Address
Chassis
=======================================================================
0
AT-MCF2000
11:22:33:44:55:55
Yes
Slot ID
Module Name
Module Type
Bootloader Version
----------------------------------------------------------------M
AT-MCF2000M
v3.0.0
1
Reg 1 traf
AT-MCF2012LC
v3.0.0
2
Reg 2 traf
AT-MCF2012LC/1
v3.0.0
=======================================================================
1
ACT Traffic
11:22:33:44:22:22
No
AT-MCF2300
Slot ID
Module Name
Module Type
Bootloader Version
----------------------------------------------------------------1
Reg 7 traf
AT-MCF2012LC
v3.0.0
2
Reg 8 traf
AT-MCF2012LC
v3.0.0
3
Reg 9 traf
AT-MCF2012LC
v3.0.0
4
Reg 10 traf
AT-MCF2012LC
v3.0.0
=======================================================================
2
UJ Traffic
11:22:33:44:66:77
No
AT-MCF2000
Slot ID
Module Name
Module Type
Bootloader Version
----------------------------------------------------------------1
District 1
AT-MCF2012LC
v3.0.0
2
District 2
AT-MCF2012LC
v3.0.0
Figure 44. DIAGNOSTICS SHOW BOOTLOADER Command
The fields are defined here:
Table 26. DIAGNOSTICS SHOW BOOTLOADER Command
Parameter
228
Description
Chassis ID
Displays the ID number of a chassis. The range is 0 to 31. For
background information, refer to “Chassis ID Numbers” on
page 25.
Chassis Name
Displays the name of a chassis. To set the chassis name, refer
to “SYSTEM SET CHASSIS” on page 59.
Chassis Type
Displays the model name of a chassis.
MAC Address
Displays the MAC address of a chassis. When communicating
with a network, the AT-MCF2000M Management Module uses
this address as its own address.
AT-S85 and AT-S97 Management Software User’s Guide
Table 26. DIAGNOSTICS SHOW BOOTLOADER Command
Parameter
Description
Master Chassis
Indicates whether the chassis contains the AT-MCF2000M
Management Module or the AT-MCF2000S Stacking Module.
A chassis with the management card will have a status of Yes,
and a unit with the stacking module will have a status of No.
Slot ID
Lists the slots in the chassis. Slots that are empty are not
included in the window. The slots are:
ˆ
M: Indicates the management slot and the AT-MCF2000M
Management Module.
ˆ
number: Indicates a slot for a media converter module
number (for example, 1, 2, etc.).
This command does not display the AT-MCF2000S Stacking
Module.
Module Name
Displays a module’s name. To assign a name, refer to
“SYSTEM SET MODULE” on page 89.
Module Type
Displays the model names of the modules.
Bootloader Version
Displays the version numbers of the bootloader files on the
modules.
Example
diagnostics show bootloader
229
Chapter 14: Diagnostics Commands
DIAGNOSTICS SHOW CHASSIS
Syntax
diagnostics show chassis id=chassis eeprom
Parameters
id
Identifies the ID number of a chassis. You can specify only
one chassis at a time. The range is 0 to 31. To view a unit’s
ID number, see “SYSTEM SHOW CLUSTER” on
page 101. For background information, refer to “Chassis ID
Numbers” on page 25.
Privilege Levels
Administrator, read-write, and read-only.
Description
This command is used to display hardware information about the modules
in a chassis. You may need to provide this information if you contact Allied
Telesis Technical Support for assistance.
Slot
Module
Module
Serial HW
MAC
ID
Name
Type
Number Rev
Address
---------------------------------------------------------------------C
AT-MCF2000 A03678L072000004
A 00:15:77:70:7A:2A
M
AT-MCF2000M
5A
A 00:15:77:70:7A:2B
1 Reg 1 Traf
AT-MCF2012LC
20
A 00:15:77:70:7A:2C
2 Reg 2 Traf
AT-MCF2012LC
14
A 00:15:77:70:7A:2D
A
AT-MCF2KFAN
8
A
B
AT-MCF2000AC
68
A
Figure 45. DIAGNOSTICS SHOW CHASSIS EEPROM Command
230
AT-S85 and AT-S97 Management Software User’s Guide
The columns are defined here:
Table 27. DIAGNOSTICS SHOW CHASSIS EEPROM Command
Column
Slot ID
Description
Lists the slots in the chassis. Empty slots and the
AT-MCF2000S Stacking Module are not included. The slots
are:
ˆ
C: Indicates the chassis.
ˆ
M: Indicates the management slot containing the
AT-MCF2000M Management Module.
ˆ
number: Indicates a slot for a media converter module
number (for example, 1, 2, etc.).
Module Name
Displays a module’s name. To assign a name to a module,
refer to “SYSTEM SET MODULE” on page 89.
Module Type
Displays the model names of the modules.
Serial Number
Displays the serial numbers of the modules.
HW Rev
Displays the hardware revision levels of the components.
MAC Addresses
Displays the MAC addresses of the chassis, the management
module, and the media converter modules. Only the MAC
address that belongs to the chassis is actually assigned at the
factory. The management module and the media converter
modules derive their MAC addresses from the chassis’ MAC
address and their slot assignments. (Each module is actually
assigned two MAC addresses, one displayed and one hidden.)
When the management module communicates with a network
through its 10/100/1000Base-T port, it always uses the
chassis’ address. So if you want a DHCP or BOOTP server to
assign the module a static IP address, enter the chassis’
address on the server.
Examples
This command displays the serial numbers, hardware version numbers,
and MAC addresses of the modules in a chassis with the ID 0:
diagnostics show chassis id=0 eeprom
231
Chapter 14: Diagnostics Commands
DIAGNOSTICS SHOW MODULE
Syntax
diagnostics show module id=chassis/slot
Parameters
id
Specifies a module. You can view only one module at a
time. The ID consists of the following parts:
chassis
Identifies an ID number of a chassis. The range
is 0 to 31. The ID number of a chassis with a
management module is either 0 or 31. The
range of the ID number for a chassis with a
stacking module is 1 to 30. For background
information, refer to “Chassis ID Numbers” on
page 25.
slot
Specifies a letter or an ID number of a slot with
a module you want to reset. Slot numbers are
explained in “Slot Numbers and Letters” on
page 26. The possible values are:
1 or 2
Specifies a slot number of a media
converter module in the
AT-MCF2000 Chassis. The left slot
is 1 and the right slot is 2.
1 to 4
Specifies a slot number of a media
converter module in the
AT-MCF2300 Chassis. The slots are
number 1 (left) and 2 (right) in the top
row, and 3 (left) and 4 (right) in the
bottom row.
m
Identifies the management slot with
the AT-MCF2000M Management
Module.
To view the ID and slot numbers of a chassis, refer to
“SYSTEM SHOW CHASSIS” on page 99 or “SYSTEM
SHOW CLUSTER” on page 101.
Privilege Levels
Administrator, read-write, and read-only.
232
AT-S85 and AT-S97 Management Software User’s Guide
Description
This command is used to display manufacturing and operational
information about the modules in a chassis. You might need to provide this
information in the event you contact Allied Telesis Technical Support for
assistance. Figure 46 on page 233 is an example of the information.
Eeprom Information
Name .......................
Model ......................
MAC ........................
SN .........................
HW Rev .....................
CPU Software Information:
Software Version ...........
CPU Information:
Name .......................
Module Type ................
Module Status ..............
Module Present .............
1.2V .......................
1.8V .......................
2.5V .......................
3.3V .......................
12.0V ......................
Temperature ................
Temperature Threshold ......
AT-MCF2012LC
00:15:77:70:7A:22
14
1
v2.0.0
AT-MCF2012LC
Active
Present
Good = 1.198
Good = 1.804V
Good = 2.509
Good = 3.302V
Good = 12.6224
38.15 C
60 C
Figure 46. DIAGNOSTICS SHOW MODULE Command
The fields in the display are defined here:
Table 28. DIAGNOSTICS SHOW CHASSIS EEPROM Command
Parameter
Description
Name
Displays a module’s name. To assign a name to a module,
refer to “SYSTEM SET MODULE” on page 89.
Model
Displays the model name of a module.
MAC Addresses
Displays the MAC address of a module. The management
module and the media converter modules derive their MAC
addresses from the chassis’ MAC address and their slot
assignments. (Each module is actually assigned two MAC
addresses, one displayed and one hidden.)
The MAC address of the management module is always the
MAC address of the chassis plus 1. For example, if the
chassis’ MAC address is 00:15:88:95:FC:A4, the management
module will assign itself the address 00:15:88:95:FC:A5.
233
Chapter 14: Diagnostics Commands
Table 28. DIAGNOSTICS SHOW CHASSIS EEPROM Command
Parameter
Description
SN
Displays the serial number of a module.
HW Rev
Displays the hardware revision levels of the component.
Software Version
The version number of the AT-S85 or AT-S97 Management
Software.
Voltages
Displays the module’s input voltages.
Temperature
Displays the current temperature of the module.
Temperature Threshold
Displays the temperature threshold of a module. The
management module logs an event in the event log if the
threshold is exceeded, to warn of possible excessive
temperature in the wiring closet or chassis. Refer to “SYSTEM
SET MODULE” on page 89 for instructions on setting a
module’s temperature threshold.
Examples
This command displays information about the management module in a
chassis with the ID 0:
diagnostics show module id=0/m
This command displays information about the media converter module in
slot 2 of a chassis with the ID 1:
diagnostics show module id=1/2
234
AT-S85 and AT-S97 Management Software User’s Guide
DIAGNOSTICS SHOW SOFTWARE
Syntax
diagnostics show software
Parameters
none
Privilege Levels
Administrator, read-write, and read-only.
Description
This command displays the version number of the AT-S85 and
AT-S97 software. If you contact Allied Telesis Technical Support for
assistance, you need to provide this information. Figure 45 is an example
of the DIAGNOSTIC SHOW SOFTWARE command.
235
Chapter 14: Diagnostics Commands
Chassis
Chassis
Chassis
MAC
Master
ID
Name
Type
Address
Chassis
=========================================================================
0
AT-MCF2000
11:22:33:44:55:55
Yes
Slot ID
Module Name
Module Type
Software Version
-----------------------------------------------------------------M
AT-MCF2000M
v3.0.0
1
Reg 1 traf
AT-MCF2012LC
v3.0.0
2
Reg 2 traf
AT-MCF2012LC/1
v3.0.0
=========================================================================
1
ACT Traffic
11:22:33:44:22:22
No
AT-MCF2300
Slot ID
Module Name
Module Type
Software Version
-----------------------------------------------------------------1
Reg 7 traf
AT-MCF2012LC
v3.0.0
2
Reg 8 traf
AT-MCF2012LC
v3.0.0
3
Reg 9 traf
AT-MCF2012LC
v3.0.0
4
Reg 10 traf
AT-MCF2012LC
v3.0.0
=========================================================================
2
UJ Traffic
11:22:33:44:66:77
No
AT-MCF2000
Slot ID
Module Name
Module Type
Software Version
-----------------------------------------------------------------1
District 1
AT-MCF2012LC
v3.0.0
2
District 2
AT-MCF2012LC
v3.0.0
Figure 47. DIAGNOSTICS SHOW BOOTLOADER Command
The fields are defined here:
Table 29. DIAGNOSTICS SHOW BOOTLOADER Command
Parameter
236
Description
Chassis ID
Displays the ID number of the chassis. The range is 0 to 31.
For background information, refer to “Chassis ID Numbers” on
page 25.
Chassis Name
Displays the name of the chassis. To set the chassis name,
refer to “SYSTEM SET CHASSIS” on page 59.
Chassis Type
Displays the model name of the chassis.
MAC Address
Displays the MAC address of the chassis.
AT-S85 and AT-S97 Management Software User’s Guide
Table 29. DIAGNOSTICS SHOW BOOTLOADER Command
Parameter
Description
Master Chassis
Indicates whether the chassis contains the AT-MCF2000M
Management Module or the AT-MCF2000S Stacking Module.
A chassis with the management card will have a status of Yes,
and a unit with the stacking module will have a status of No.
Slot ID
Lists the slots in the chassis. Slots that are empty are not
included. The slots are:
ˆ
M: Indicates the management slot containing the
AT-MCF2000M Management Module.
ˆ
number: Indicates a slot for a media converter module
number (for example, 1, 2, etc.). Empty slots are not
included in the tables.
This command does not display the AT-MCF2000S Stacking
Module.
Module Name
Displays a module’s name. To assign a name, refer to
“SYSTEM SET MODULE” on page 89.
Module Type
Displays the model names of the modules.
Software Version
Displays the version numbers of the AT-S85 and
AT-S97 Software on the modules.
Example
diagnostics show software
237
Chapter 14: Diagnostics Commands
238
Appendix A
AT-S85 and AT-S97 Management
Software Default Settings
This appendix lists the factory default settings for the features in the
AT-S85 and AT-S97 Management Software. The sections are:
ˆ
“AT-S85 Management Software” on page 240
ˆ
“AT-S97 Management Software” on page 241
239
Appendix A: AT-S85 and AT-S97 Management Software Default Settings
AT-S85 Management Software
The following table lists the default settings for the AT-S85 Management
Software and the AT-MCF2012LC, AT-MCF2012LC/1 and
AT-MCF2032SP Media Converter Modules.
Table 1. Default Settings for the AT-S85 Management Software
Parameter
240
Default Setting
Auto-Negotiation
Enabled
Channel Name
None
Egress Rate Limiting
None
Ingress Rate Limiting
None
Module Name
None
Operating Mode
Link Test
Port Status
Enabled
Temperature Threshold
60° C (140° F)
AT-S85 and AT-97 Management Software User’s Guide
AT-S97 Management Software
The following table lists the default settings for the AT-S97 Management
Software and the AT-MCF2000M Management Module.
Table 2. Default Settings for the AT-S97 Management Software
Parameter
Default Setting
Event Log
Status
Enabled
Severity Level
Event
IP Address
IP Address
10.0.0.1
Subnet Mask
255.255.252.0
Default Gateway
0.0.0.0
Manager Account1
Manager Login Name
manager
Manager Password
friend
Console Timer
10 minutes
Master Configuration File
Default Master Configuration File
none
Overwrite
Enabled
Network Time Protocol Client
Client Status
Disabled
NTP Server IP Address
0.0.0.0
Universal Time Coordinated (UTC) Offset
0 hours
RS-232 Terminal Port
Data Bits
8
Stop Bits
1
Parity
None
Flow Control
None
Baud Rate2
115200 bps
241
Appendix A: AT-S85 and AT-S97 Management Software Default Settings
Table 2. Default Settings for the AT-S97 Management Software
Parameter
Default Setting
Secure Shell Server
SSH Server
Disabled
Protocol Port Number3
22
Simple Network Management Protocol
get community
public
set community
private
trap community
public
Manager 1 IP address
0.0.0.0
Manager 2 IP address
0.0.0.0
Manager 3 IP address
0.0.0.0
Manager 4 IP address
0.0.0.0
Syslog Client
Syslog Server IP Address
0.0.0.0
Facility Code
0
Severity Level
Event
Telnet Server
Telnet Server
Disabled
Protocol Port Number4
23
1.
2.
3.
4.
242
Login names and passwords are case sensitive.
The baud rate is the only adjustable parameter on the port.
The protocol port number is not adjustable.
The protocol port number is not adjustable.
Index
Numerics
B
10/100/1000Base-T Management port
displaying status of 111
setting 92
C
A
active master configuration file
described 149
displaying name of 166
running 158, 160
setting 164
updating 23, 161
AT-MCF2000AC Power Supply Modules
displaying status of 111
naming 89
setting temperature threshold 89
AT-MCF2000M Management Modules
displaying 99, 101, 111
displaying file system on 191
naming 89
resetting 74, 78
setting 10/100/1000Base-T Management port 92
setting temperature threshold 89
AT-MCF2012LC and AT-2012LC/1 Modules. See media
converter modules
AT-MCF2KFAN Fan Modules
displaying status of 111
naming 89
setting temperature threshold 89
AT-S85 boot loader files, downloading 179, 186
AT-S85 Management Software
default values 240
described 16
displaying version number 99, 101
downloading 179, 186
AT-S97 boot loader files, downloading 179, 186
AT-S97 Management Software
default values 241
described 16
displaying version number 99, 101
downloading 179, 186
setting command line prompt 64
Auto-Negotiation, setting 92
auxiliary configuration files
described 146
displaying names of 191
boot loader files, downloading 179, 186
channel operating modes
described 82
displaying 103
guidelines 85
setting 81
chassis ID numbers
described 25
displaying 99, 101, 103
CLEAR command 41
command line prompt, setting 64
commands
CLEAR 41
CONFIG OVERWRITE 158
CONFIG RUN 160
CONFIG SAVE 161
CONFIG SAVE FILESYSTEM 162
CONFIG SET 164
CONFIG SHOW 166
DIAGNOSTICS SHOW CHASSIS 227, 230
DIAGNOSTICS SHOW MODULE 232
EXIT 42
FILE COPY 173
FILE DELETE 176
FILE DOWNLOAD 179
FILE FASTDOWNLOAD 186
FILE RENAME 188
FILE SHOW 191
FILE UPLOAD 194
HELP 43
IP DHCP DISABLE 50
IP DHCP ENABLE 51
IP SET 52
IP SHOW 54
LOGGING CLEAR EVENTLOG 128
LOGGING DISABLE EVENTLOG 129
LOGGING DISABLE SYSLOG 130
LOGGING ENABLE EVENTLOG 131
LOGGING ENABLE SYSLOG 132
LOGGING SET EVENTLOG 133
LOGGING SET SYSLOG 135
LOGGING SHOW 136
LOGGING SHOW EVENTLOG 138
NTP DISABLE 120
NTP ENABLE 121
NTP SET 122
243
Index
NTP SHOW 123
PING 44
SNMP SET 206
SNMP SHOW 208
SSH DISABLE 212
SSH ENABLE 213
SSH SHOW 214
SYSTEM RESET CHASSIS 74
SYSTEM RESET CLUSTER 76
SYSTEM RESET MODULE 78
SYSTEM SET ASYNCHRONOUS 58
SYSTEM SET CHASSIS 59
SYSTEM SET CLOCK 60
SYSTEM SET CONSOLE 62
SYSTEM SET CONTACT 63
SYSTEM SET HOSTNAME 64
SYSTEM SET INTERFACE 81
SYSTEM SET LOCATION 65
SYSTEM SET MODULE 89
SYSTEM SET PORT 92
SYSTEM SHOW ASYNCHRONOUS 66
SYSTEM SHOW CHASSIS 99
SYSTEM SHOW CLOCK 67
SYSTEM SHOW CLUSTER 101
SYSTEM SHOW CONSOLE 68
SYSTEM SHOW INFO 69
SYSTEM SHOW INTERFACE 103
SYSTEM SHOW MODULE 111
TELNET DISABLE 200
TELNET ENABLE 201
TELNET SHOW 202
USER ADD 218
USER DELETE 220
USER SET 221
USER SHOW 223
commands, formatting 29
CONFIG OVERWRITE command 158
CONFIG RUN command 160
CONFIG SAVE command 161
CONFIG SAVE FILESYSTEM command 162
CONFIG SET command 164
CONFIG SHOW command 166
configuration files
command summary 157
copying 173
creating 148, 162
deleting 176
described 146
displaying names of 191
downloading 171, 179
editing 150
renaming 188
setting active master file 164
updating 23
uploading 171, 194
configuration overwrite setting
configuring 158
described 146
244
console timer
described 62
displaying 68
setting 62
contact name
displaying 69
setting 63
copying configuration files 173
creating
manager accounts 218
new master configuration files 162
D
default gateway address
displaying 54
setting with a DHCP server 51
setting, manually 52
default values
applying 76
AT-S85 Management Software 240
AT-S97 Management Software 241
deleting
configuration files 176
event messages 128
manager accounts 220
DHCP client
disabling 50
displaying status of 54
enabling 51
diagnostics commands 226
DIAGNOSTICS SHOW CHASSIS command 227, 230
DIAGNOSTICS SHOW MODULE command 232
disabling
Auto-Negotiation 92
DHCP client 50
event log 129
media converter ports 92
Network Time Protocol (NTP) client 120
Secure Shell (SSH) server 212
syslog client 130
Telnet server 200
displaying
10/100/1000Base-T Management port 111
active master configuration file 166
baud rate of RS232 Terminal port 66
chassis contact 69
chassis ID numbers 99, 101, 103
chassis, location of 69
chassis, name of 69, 99, 101
console timeout 68
current master configuration file 166
date and time 67
event messages 138
facility code for event messages 136
file systems 191
IP address of Network Time Protocol (NTP) server 123
IP address of syslog server 136
IP configuration 54
MAC address 99, 101
AT-S85 and AT-S97 Management Software User’s Guide
manager accounts 223
severity level of event messages 136
status of
AT-MCF2000AC Power Supply Modules 111
AT-MCF2000M Management Modules 111
AT-MCF2KFAN Fan Modules 111
event log 136
media converter channels 103
media converter modules 111
media converter ports 103
Network Time Protocol (NTP) client 123
Secure Shell (SSH) server 214
Simple Network Management Protocol (SNMP)
208
syslog client 136
Telnet server 202
document conventions 12
downloading files 179
E
egress rate limits
displaying 103
setting 92
enabling
Auto-Negotiation 92
event log 131
media converter ports 92
Network Time Protocol (NTP) client 121
Secure Shell (SSH) server 213
syslog client 132
Telnet server 201
event log
command summary 127
deleting messages 128
described 126
disabling 129
displaying messages 138
displaying status 136
enabling 131
setting severity level 133
EXIT command 42
F
fiber optic ports
configuring 92
displaying 103
FILE COPY command 173
FILE DELETE command 176
FILE DOWNLOAD command 179
FILE FASTDOWNLOAD command 186
FILE RENAME command 188
FILE SHOW command 191
file systems
command summary 172
described 170
displaying 191
FILE UPLOAD command 194
H
HELP command 43
help, context-sensitive 28
I
ingress rate limits
displaying 103
setting 92
IP address
displaying 54
setting with a DHCP server 51
setting, manually 52
IP configuration
displaying 54
setting with a DHCP server 51
setting, manually 52
IP DHCP DISABLE command 50
IP DHCP ENABLE command 51
IP SET command 52
IP SHOW command 54
K
keyword abbreviations 28
L
Link Test operating mode
described 82
setting 81
local management sessions
ending 24, 42
starting 18
LOGGING CLEAR EVENTLOG command 128
LOGGING DISABLE EVENTLOG command 129
LOGGING DISABLE SYSLOG command 130
LOGGING ENABLE EVENTLOG command 131
LOGGING ENABLE SYSLOG command 132
LOGGING SET EVENTLOG command 133
LOGGING SET SYSLOG command 135
LOGGING SHOW command 136
LOGGING SHOW EVENTLOG command 138
M
MAC address, displaying 99, 101
manager accounts
command summary 216
creating 218
deleting 220
described 216
displaying 223
guidelines 216
modifying 221
privilege levels, described 17, 216
master configuration files
copying 173
creating 148, 162
deleting 176
described 146
displaying names of 191
245
Index
downloading 171, 179, 186
editing 150
renaming 188
setting active file 164
uploading 171, 194
media converter channels
displaying 103
setting operating modes 81
setting ports 92
media converter chassis
displaying 99, 101, 103
naming 59
media converter modules
command summary 72
displaying 99, 101, 103, 111
displaying file systems 191
naming 89
resetting 74, 78
setting operating modes 81
setting ports 92
setting temperature thresholds 89
media converter ports 103
MissingLink operating mode
described 82
setting 81
Mode Select button 85
N
naming
AT-MCF2000AC Power Supply Modules 89
AT-MCF2KFAN Fan Modules 89
channels 87
management and media converter modules 89
media converter chassis 59
stacks 64
Network Time Protocol (NTP) client
command summary 118
described 118
disabling 120
displaying status of 123
enabling 121
guidelines 118
setting server’s IP address 122
NTP DISABLE command 120
NTP ENABLE command 121
NTP SET command 122
NTP SHOW command 123
O
operating modes. See channel operating modes
operator accounts. See manager accounts
overwrite setting
configuring 158
described 146
P
password, default 19
PING command 44
port command summary 72
246
port speeds
configuring 92
displaying 103
R
renaming configuration files 188
resetting
chassis 74
management module 78
media converter modules 78
RS-232 Terminal port
adjusting baud rate 58
displaying baud rate 66
S
Secure Shell (SSH) management sessions
ending 24, 42
starting 20
Secure Shell (SSH) server
command summary 211
described 210
disabling 212
displaying status 214
enabling 213
guidelines 210
setting
10/100/1000Base-T Management port 92
active master configuration file 164
Auto-Negotiation 92
baud rate of RS-232 Terminal port 58
channel operating modes 81
chassis contact 63
chassis location 65
chassis name 59
console timeout 62
egress rate limits 92
event log severity level 133
facility level of event messages 135
ingress rate limits 92
IP address of Network Time Protocol (NTP) server 122
IP address of syslog server 135
IP configuration 52
manager account passwords 221
manually, date and time 60
MDI/MDI-X parameter 92
media converter ports 92
module names 89
Simple Network Management Protocol (SNMP) 206
stack name 64
syslog client severity level 133
temperature thresholds 89
Simple Network Management Protocol (SNMP)
command summary 205
described 204
displaying status 208
guidelines 204
overview 204
setting community strings 206
setting IP addresses of trap receivers 206
AT-S85 and AT-S97 Management Software User’s Guide
trap events 204
Smart MissingLink operating mode
described 84
setting 81
SNMP SET command 206
SNMP SHOW command 208
SNMP. See Simple Network Management Protocol
SSH DISABLE command 212
SSH ENABLE command 213
SSH SHOW command 214
stack name
displaying 69
setting 64
subnet mask
displaying 54
setting with a DHCP server 51
setting, manually 52
syslog client
command summary 127
described 126
disabling 130
displaying status of 136
enabling 132
guidelines 126
setting facility code 135
setting server’s IP address 135
setting severity level 133
system commands, summary 56, 72
system location
displaying 69
setting 65
SYSTEM RESET CHASSIS command 74
SYSTEM RESET CLUSTER command 76
SYSTEM RESET MODULE command 78
SYSTEM SET ASYNCHRONOUS command 58
SYSTEM SET CHASSIS command 59
SYSTEM SET CLOCK command 60
SYSTEM SET CONSOLE command 62
SYSTEM SET CONTACT command 63
SYSTEM SET HOSTNAME command 64
SYSTEM SET INTERFACE command 81
SYSTEM SET INTERFACE PORTNAME command 87
SYSTEM SET LOCATION command 65
SYSTEM SET MODULE command 89
SYSTEM SET PORT command 92
SYSTEM SHOW ASYNCHRONOUS command 66
SYSTEM SHOW CHASSIS command 99
SYSTEM SHOW CLOCK command 67
SYSTEM SHOW CLUSTER command 101
SYSTEM SHOW CONSOLE command 68
SYSTEM SHOW INFO command 69
SYSTEM SHOW INTERFACE command 103
SYSTEM SHOW MODULE command 111
system time
displaying 67
setting with a Network Time Protocol (NTP) server 118
setting, manually 60
T
TELNET DISABLE command 200
TELNET ENABLE command 201
Telnet management sessions
ending 24, 42
starting 20
Telnet server
command summary 198
described 198
disabling 200
displaying status 202
enabling 201
guidelines 198
TELNET SHOW command 202
temperature thresholds
displaying 111
setting 89
time. See system time
twisted pair ports
configuring 92
displaying 103
U
updating active master configuration file 23, 161
uploading configuration files 194
USER ADD command 218
USER DELETE command 220
USER SET command 221
USER SHOW command 223
247
Index
248