Firebox Liner Kit
Model # 24183-RLK
24188-RLK
24193-RLK
ECHELON
Parts List
Firebox
liner
pieces
Smoker
drawer
cover
Air
baffle
E1060 24183-RLK
5
1
24188-RLK
5
E660 24193-RLK
* Not shown
† Includes 4 extra
drive screws
5
Model
E790
Part No.
Flash
tube
plate
3
4
4
12
16
4
2
1
1
3
3
12
14
3
2
1
1
3
3
12
14
3
2
Table 1
Air baffles
W
DR
R R
KE VE
CO
O
6
ER
LIN FT
LE
2
Liner left
2
LIN
BA ER
CK
9
6
Smoker
drawer
cover
4
Drill
bit
(2mm)*
Drive Self-tapping Flavor
screw † hex screw
grid *
SM
4
Flash
tube
Liner back
7
BA AIR
FF
LE
9
7
8
AIR LE
FF
BA
8
BA AIR
FF
LE
(1060 models)
7
BA AIR
FF
LE
7
(790 models)
1
L
CE INER
NT
ER
1
7
BA AIR
FF
LE
7
Liner center
(660 models)
Flash
tube
5
3
Liner Front
Drive screw
Liner right
Flash tube
plate
E1060 kit shown
Self-tapping
hex screw
This firebox liner kit is for installation on Echelon grills. Installation on an E1060 is depicted in this instruction.
READ THESE INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION.
Tools required: Gloves, Phillips screwdriver, power drill, 3/32" drill bit, rubber mallet, pliers, needle-nose pliers,
hammer, and a 1/4" nut driver (or equivalent).
Be sure the grill is completely cool and the gas is completely shut off.
IMPORTANT: CLEAN THE INTERIOR OF THE GRILL OF ALL DEPOSITS AND GREASE PRIOR TO
INSTALLING THE FIREBOX LINER KIT.
Note: Wear gloves whenever installing and handling this liner kit as some components have sharp edges.
I
As applicable, remove the warming rack, cooking grids, flavor grids, zone separators, burners, burner
igniters, infrared burners, infrared burner igniters, air baffles, and flash tubes. Open the control panel. If
the smoker drawer assembly is not welded down, remove it as well. Reference your owner's manual for
removal details if needed.
Note: The flavor grids, air baffles, and flash tubes that are being removed from your grill are no longer
needed and may be discarded. The items included in this kit will replace these parts.
ROBERT H. PETERSON CO. • 14724 East Proctor Avenue • City of Industry, CA 91746
REV 0 - 1512070750
1
L-C2-476
II
B
Install
center
liner
Install rear liner
III
Bend liner from crease
for ease of installation
(if needed)
C
A
1
LINER
CENTER
LINER
BACK
LINER
CENTER
Tabs must clear
the openings
Place the center liner (item 1 of parts list) into the grill
drainage channel (A). The liner will need to be bent in order
to slide it under the smoker drawer (B). Ensure the liner
rests flat in place (C).
Note:
It is recommended to slightly bend the 4 tabs
inward to assist in front and rear liner installation.
Note:
If smoker drawer assembly was removed, re-install
it at this time.
IV
2
1
Place the rear liner (item 2) ensuring it rests flat against
grill rear firebox wall. The two tabs (on center liner) must
extend up through the slots in the rear liner.
Note:
If needed, use a rubber mallet to assist in
proper placement of liner panels.
V
Tabs must clear
the openings
Place left liner
Install front
liner
2
LINER
BACK
ER
LIN FT
LE
4
LINER
1 CENTER
LINER
3 FRONT
The drive screws
must be aligned
when hammering
Place the front liner (item 3) ensuring it rests flat against
the grill front firebox wall, and the two tabs (on center liner)
extend up through the slots in the front liner.
Note:
Existing
firebox
If needed, the thermocouples may be removed for
ease of the front liner installation.
New left
liner
Existing
ting
firebox
New left
liner
New
liner
flange
New liner
flange
CORRECT
INCORRECT
Place the left liner (item 4) as shown above. Rest the liner
OVER the front and rear liner flanges (hiding the flanges)
and ensure the 4 holes are aligned with the 4 grill wall rivets.
To secure the liner, align each drive screw (included in kit)
with the corresponding hole and carefully hammer each
drive screw into the panel. Use needle-nose pliers to assist
in holding the drive screws properly.
Note:
The drive screw will force out the center of
the existing rivet. Therefore, ensure to use
ample force when driving the screw through
the retaining rivet.
REPEAT THIS STEP FOR THE RIGHT LINER (item 5).
Procedure continued on next page
REV 0 - 1512070750
2
L-C2-476
VI
VII
Bend
tabs inward
Install smoker
drawer cover
2
LINER
BACK
5
2
x8
LINER
6
1 CENTER
SMOKER DRW
COVER
LINER
RIGHT
LINER
BACK
LINER
1 CENTER
LINER
3 FRONT
LINER
3 FRONT
Using pliers, bend in the four tabs inward toward the middle
of the center liner to lock the liner panels together.
VIII
A
B
Pre-drill pilot holes through the original grill liner using the
supplied drill bits. Place the smoker drawer cover (item 6)
ensuring it rests flat on the original smoker drawer. Fasten
using the provided self-tapping hex screws and a 1/4" nut
driver or equivalent.
Flash tube
Flash tube
plate
x2
(per flash tube)
Install the provided flash tube and flash tube plate by
aligning the plate (A) and flash tube (B) to the original liner
mounting holes. Using a 1/4" nut driver or equivalent, affix
with the supplied hex screws. Repeat this procedure for
the other flash tubes.
IX
E1060 Models
E790 Models
E660 Models
Item 9
9B
A
AF IR
FL
E
Item 7
Item 7
7B
A
AF IR
FL
E
Item 7
7B
A
AF IR
FL
E
AIR LE
FF
7 BA
Item 8
SM
6
6
SM
OK
CO ER
VE DR
R W
OK
CO ER
VE DR
R W
SM
6
OK
CO ER
VE DR
R W
8B
A
AF IR
FL
E
Install the air baffles according to your model above. To properly install, the tabs must slide into the slots located on the liners.
X
Install the burners, burner igniters, infrared burners (if applicable), infrared burner igniters (if applicable), thermocouples
(if removed), zone separators, new flavor grids, the control panel, cooking grids, and warming rack. Reference your
owner's manual for installation details if needed.
REV 0 - 1512070750
3
L-C2-476
NOTES PAGE
Please use this page to record any information about your unit that you may want to have at hand.
REV 0 - 1512070750
4
L-C2-476