S3 Cast Iron Separator Flanged

TI-P023-24
ST Issue 4
S3
Cast Iron
Separator (Flanged)
Cert. No. LRQ 0963008
ISO 9001
2
3
1
4
The S3 separator is a cast iron baffle type separator used for the
removal of entrained liquids in steam, compressed air or gas systems.
The fitting of insulation jackets will increase the performance of the
separator.
Standards
This product fully complies with the requirements of the European
Pressure Equipment Directive 97 /23 /EC.
Certification
This product is available with a manufacturers' Typical Test Report.
Note: All certification / inspection requirements must be stated at
the time of order placement.
���
A
���
Steam
saturation
curve
���
��
�
���
�
�
�
�
�
��
��
B
��
A
��
Pressure bar g
The product must not be used in this region.
Sizes and pipe connections
DN40, DN50, DN65, DN80, DN100, DN125, DN150 and DN200
Flanged EN 1092 PN16 with screwed BSP drain,
ANSI Class 125 with screwed NPT drain,
JIS /KS 10K with screwed BSP drain, and
AS2129 Table F with screwed BSP drain (DN40 to DN100 only).
Materials
No. Part
Material
1
Body
Cast iron
2
Plug
SG iron
3
Gasket
Reinforced exfoliated graphite
4
Drain reducing
bush (not DN200)
Steel
Pressure / temperature limits (ISO 6552)
Temperature °C
Description
ASTM A126 CI B
DIN 1693 GGG 40
ASTM A105
A - A Flanged EN 1092 PN16 and Table F.
A - B Flanged ANSI Class 125 and JIS/KS 10K.
Body design conditions
PN16
PMA Maximum allowable pressure
16 bar g @ 0°C
TMA Maximum allowable temperature
184°C @ 10 bar g
Minimum allowable temperature
-10°C
Maximum operating pressure
PMO for saturated steam service
10 bar g
TMO Maximum operating temperature
184°C @ 10 bar g
Minimum operating temperature
-10°C
Note: For lower operating temperatures consult Spirax Sarco.
Designed for a maximum cold hydraulic test pressure of 24 bar g
Note: S3 Flanged type separators may be supplied with a lower
pressure rating than that cast into the body. Reference should be
made to the appropriate operating chart to determine the actual
product limitations.
Local regulations may restrict the use of this product to below the conditions quoted.
In the interests of development and improvement of the product, we reserve the right to change the specification without notice.
© Copyright 2008
Dimensions /weights and volumes
Recommended tightening torques
Size
Item
(approximate) in mm, kg and litres
A
B
C
D
E
F
G
Weight Volume
DN40
111 156
89
365
½" 1½"
94
14.0
1.6
DN50
146 206
117 456
½" 1½"
98
25.4
3.2
DN65
184 232
146 406
¾" 1½"
98
36.7
4.6
DN80
187 264
152 483
1" 1½"
98
44.9
6.5
DN100 238 337
197 692
1" 1½" 118
74.8
13.5
DN125 232 409
381 706
1" 1½" 121 177.8
38.5
DN150 232 409
381 706
1" 1½" 121 181.4
42.5
DN200 305 505
426 762 1½" 1½" 140 254.0
68.0
or
mm
Size
DN40
DN50
DN65
DN80
DN100
DN125
DN150
DN200
2
46 A /F
60 A /F
46 A /F
60 A /F
60 A /F
60 A /F
60 A /F
60 A /F
Nm
M56
M72
M56
M72
M72
M72
M72
M72
150 - 165
150 - 165
150 - 165
190 - 210
190 - 210
190 - 210
190 - 210
190 - 210
2 Inspection opening (2" only)
B
A
Separator drain tapping F
G
Drain E
C
D
Safety information, installation and maintenance
For full details see the Installation and Maintenance Instructions (IM-P023-55) supplied with the product.
Installation note:
Install in a horizontal pipeline with the drain directly below. Note: To ensure that any separated liquid is drained away quickly, a suitable
liquid drainer or steam trap must be connected to the drain connection 'E' - consult Spirax Sarco for further details.
Disposal
This product is recyclable. No ecological hazard is anticipated with the disposal of this product, providing due care is taken.
How to order
Example: 1 off DN50 Spirax Sarco S3 separator with cast iron body having flanged EN 1092 PN16 connections.
S3 Cast Iron Separator (Flanged)
TI-P023-24 ST Issue 4