PLEASE READ THIS MANUAL CAREFULLY BEFORE OPERATION MRC.VER.02-11.10

INSTRUCTION MANUAL FOR
HOG-020/020D
HOMOGENIZERS
PLEASE READ THIS MANUAL CAREFULLY BEFORE OPERATION
3, Hagavish st. Israel 58817 Tel: 972 3 5595252, Fax: 972 3 5594529 mrc@mrclab.com
MRC.VER.02-11.10
Ⅰ、OUTLINE
Speed adjuster
(H2G-0 only)
Body
Body chuck
Holding screw
Pole
Head
Stand base
Controller
(H2G-0D only)
Power switch
Speed adjuster
Ⅱ、SPECIFICATION
Model
H2G-0 / H2G-0D
Power
AC 110 / 220V , 50 / 60 Hz
Motor
AC 250W
Max. speed (rpm)
26,000
Driver
Electronic type
Safety device
Fuse
Coating
Medicine-resisting
Weight (kg)
7
1
Ⅲ、OPERATION INTRODUCTION
1. Put container on stand base and keep distance between the head and bottom of container.
2. Turn the speed button to the end of left side.
3. Put plug into socket and then switch to be “ON” to start it.
4. Adjust speed button to be proper speed per your demand.
5. When you stop it, please turn speed button to the end of left side.
6. Switch the key to be “ OFF ”.
Ⅳ、ATTENTION
1. Do not start it without any material inside container.
2. The speed has to match material’s viscosity to avoid head at empty rotation.
3. Bad fluid is not suitable to the instrument
4. Heads are changeable, please loose the holding screw and take head off.
5. After you clean or change head, please must fix and screw it tightly.
Ⅴ、INSPECTION
When the machine is out of order, please check following possible facts:
1. Fuse burns out or not。
2. Carbon brushes at both sides of motor use out or contact improperly.
3. If carbon brushes use out, then take it off and renew it.
If above have been checked and useless, please send the machine back to agent for
further examination and maintenance.
2
Ⅵ、APPLICATION OF HEADS
Model
Applicable range
*(1
To homogenize or mix on cell tissue in micro volume.
1. To disperse plant or animal tissue.
*(1
2. To treat suspensions and emulsions.
3. Homogenizing and mixing.
4. Extraction function.
1. To disperse plant or animal tissue.
*(1
2. To treat suspensions and emulsions.
3. Homogenizing and mixing.
4. Extraction function.
1. To disperse organic and inorganic matters.
*(1
2. Homogenizing and mixing.
3. Extraction function.
Ⅶ、SPECIFICATION OF HEADS
Model
Circumference Speed (m/s)
Capacity (ml)
Size (mm)
*(1
6.3
0.3~10
φ7 x 130
*(1
11.3
2~250
φ12 x 170
*(1
20.1
20~2000
φ20 x 200
*(1
29.9
100~3000
φ30 x 250
3
TO OPEN AND SEPARATED
*(1
Insult the tools into the shaft
Turn the tools to open
After open the shaft , 3 main parts from shaft *(1 as follows
Connect pipe
Shaft of connect pipe
4
Turning cutter
TO OPEN AND SEPARATED
*(1
Insult the tools into the shaft
Turn the tools to open
After open the shaft , 7 main parts from shaft *(1 as follows
Connect pipe
Bearing
Bolts
E type
washer
Shaft of
connect
pipe
5
Pipe
Turning
Cutter
TO OPEN AND SEPARATED
*(1
Insult the tools into the shaft
Turn the tools to open
After open the shaft , 8 main parts from shaft *(1 as follows
Connect pipe
Pipe
Fixed cutter
Shaft connect pipe
Bearing
Bolts
E type 6washer
Turning cutter
TO OPEN AND SEPARATED
*(1
Insult the tools into the shaft
Turn the tools to open
After open the shaft , 8 main parts from shaft *(1 as follows
Connect pipe
Pipe
Shaft connect pipe
Bearing
Bolts
7
E type washer
Fixed cutter
Turning cutter
TO ASSEMBLY
*(1
Put each parts into Accordinly with the drawing
Insult the tools into the shaft
Turn the tools to fixed
Turning cutter
Shaft of connect pipe
8
TO ASSEMBLY
*(1
Put each parts into Accordingly with the drawing
Insult the tools into the shaft
Turn the tools to fixed
9
TO ASSEMBLY
*(1
Put each parts into Accordinly with the drawing
Insult the tools into the shaft
Turn the tools to fixed
10
TO ASSEMBLY
*(1
Put each parts into Accordinly with the drawing
Insult the tools into the shaft
Turn the tools to fixed
11