Quick guide: Vivoteka IP8152

IP8152 Fixed
Network Camera
Quick Installation Guide
P/N:625020002G Rev. 1.2
6F, No.192, Lien-Cheng Rd., Chung-Ho, New Taipei City, 235, Taiwan, R.O.C.
|T: +886-2-82455282| F: +886-2-82455532| E: sales@vivotek.com
VIVOTEK Netherlands B.V.
Busplein 36, 1315KV, Almere, The Netherlands
|T: +31 (0)36 5389 149| F: +31 (0)36 5389 111| E: saleseurope@vivotek.com
繁中
Dansk
Indonesia
簡中
日本語
Français
Español
Deutsch
Português
Italiano
1.3MP • Compact Size • Supreme Night Visibility
All specifications are subject to change without notice.
Copyright c 2013 VIVOTEK INC. All rights reserved.
VIVOTEK INC.
English
VIVOTEK USA, INC.
2050 Ringwood Avenue, San Jose, CA 95131
|T: 408-773-8686| F: 408-773-8298| E: salesusa@vivotek.com
Türkçe
Polski
Русский
Česky
Svenska
Nederlands
Warning Before Installation
Power off the Network Camera as
soon as smoke or unusual odors are
detected.
Keep the Network Camera away
from water. If the Network Camera
becomes wet, power off immediately.
Do not place the Network Camera
around heat sources, such as a
television or oven.
Keep the Network Camera away from
direct sunlight.
Refer to your user's manual for the
operating temperature.
Do not place the Network Camera on
unsteady surfaces.
Do not touch the Network Camera
during a lightning storm.
Do not disassemble the Network
Camera.
Do not drop the Network Camera.
1
Do not place the Network Camera in
high humidity environments.
Package Contents
IP8152
CS-mount Lens
Quick Installation Guide
Camera Stand
Software CD
Warranty Card
5 1 0 0 0 02 2 1 G
L-type Hex Key Wrench
Screws
Mount Bracket
2
Physical Description
Front Panel
Status LED
MicroSD/
SDHC/
SDXC
Card Slot
Lens
Mount ring
adjustment
Rear Panel
Iris Control Cable Socket
1 2 3 4 5 6 7
AUDIO_OUT
MIC_IN
GND_AUDIO
RS485_P
Ethernet 10/100
RJ45 Socket
RS485_N
DI
GND
Mounting Hole
General I/O Terminal
Block
Recessed Reset Button
Lens
Focus Controller
Zoom Controller
EN - 2
English
3
Mounting the Lens to the Camera
1.Mount the lens by turning it clockwise onto the camera mount until it stops.
2.Connect the iris control cable to the socket. Connect the iris control cable before
power-on. Otherwise, you will not be able to access the exposure related
settings.
2
1
4
Mounting the Camera to Stand
1.Use the holes on the camera stand to mark drill holes on the wall. Drill holes on your
preferred location.
2.Hammer in the included plastic anchors.
3. Install the camera stand to wall or ceiling
by driving screws through it.
4.Attach the camera to stand by turning
the stand and the fastening rings.
EN - 3
5
Network Deployment
Power over Ethernet (PoE)
When using a PoE-enabled switch
The Network Camera is PoE-compliant, allowing transmission of power and data via
a single Ethernet cable. Follow the below illustration to connect the Network Camera
to a PoE-enabled switch via Ethernet cable.
PoE Switch
POWER
COLLISION
1
2
3
4
5
LINK
RECEIVE
PARTITION
When using a non-PoE switch
Use a PoE power injector (optional) to connect between the Network Camera and a
non-PoE switch.
PoE Power Injector
(optional)
POWER
COLLISION
1
2
3
4
5
LINK
RECEIVE
PARTITION
EN - 4
Non-PoE Switch
English
6
Assigning an IP Address
1. Install "Installation Wizard 2" from the Software Utility directory on the software CD.
2. The program will conduct an analysis of your network environment. After your network
is analyzed, please click on the "Next" button to continue the program.
3. The program will search for VIVOTEK Video Receivers, Video Servers, and Network
Cameras on the same LAN.
4.After a brief search, the main installer window will pop up. Double-click on the MAC
address that matches the one printed on the camera label or the S/N number on the
package box label to open a browser management session with the Network Camera.
7
Ready to Use
1.A browser session with the Network Camera should prompt as shown below.
2.You should be able to see live video from your camera. You may also install the
32-channel recording software from the software CD in a deployment consisting of
multiple cameras. For its installation details, please refer to its related documents.
For further setup, please refer to the user’s manual on the software CD.
EN - 5
3. Unscrew the zoom controller to adjust the zoom factor. Upon completion, tighten the
zoom controller.
4. Unscrew the focus controller to adjust the focus range. Upon completion, tighten the
focus controller.
∞
3
4
N
W
T
NOTE:
If you prefer other lens for your IP8152, please notice the specifications below.
1.If you select a different lens, the distance between the flange of the lens and the IR
cut filter on the camera should be smaller than 7.5mm. If the lens protrudes too much
from the bottom of the lens module, it may hit the IR Cut Filter, or result in out of focus
when adjusting the focus controller.
2. A vari-focal lens may protrude from the bottom of screw mount when tuning the focus
puller.
IR Cut
Filter
Lens
protrudes from
the screw
mount
Screw mount
mm
3. Use the included hex wrench to make adjustments to CS-mount ring only when you
experience compatibility issue with lens focal length.
EN - 6
English
Installed into Housing
1. Attach the bracket to the back of the camera by resting the foam pads on the top and
to the back of the camera. Secure the bracket by driving a hex socket screw.
The camera can be installed into VIVOTEK's
housings, such as the AE-211/-232/-233/-234/-235
series.
2. Attach the T-bracket and the camera to the camera bracket. Place the camera lens in
the front as close as possible to the enclosure's tempered glass window. Secure the
installation by tightening the hex socket screw on top.
EN - 7
IP8152 Fixed
Network Camera
Quick Installation Guide
P/N:625020002G Rev. 1.2
6F, No.192, Lien-Cheng Rd., Chung-Ho, New Taipei City, 235, Taiwan, R.O.C.
|T: +886-2-82455282| F: +886-2-82455532| E: sales@vivotek.com
VIVOTEK Netherlands B.V.
Busplein 36, 1315KV, Almere, The Netherlands
|T: +31 (0)36 5389 149| F: +31 (0)36 5389 111| E: saleseurope@vivotek.com
繁中
Dansk
Indonesia
簡中
日本語
Français
Español
Deutsch
Português
Italiano
1.3MP • Compact Size • Supreme Night Visibility
All specifications are subject to change without notice.
Copyright c 2013 VIVOTEK INC. All rights reserved.
VIVOTEK INC.
English
VIVOTEK USA, INC.
2050 Ringwood Avenue, San Jose, CA 95131
|T: 408-773-8686| F: 408-773-8298| E: salesusa@vivotek.com
Türkçe
Polski
Русский
Česky
Svenska
Nederlands