TNPW Lead (Pb)-Bearing High Stability Thin Film Chip Resistors Vishay

TNPW
www.vishay.com
Vishay
Lead (Pb)-Bearing High Stability Thin Film Chip Resistors
FEATURES
• Metal film layer on high quality ceramic
• SnPb termination plating, Pb content > 6 %
• Excellent overall stability at different environmental
conditions  0.05 % (1000 h rated power at 70 °C)
• Low temperature coefficient and tight tolerances (± 0.1 %;
± 10 ppm/K)
• Single lot date code available
APPLICATIONS
• Military
• Avionics
• Industrial
TNPW High Stability Thin Film Chip Resistors are the perfect
choice for most fields of modern electronics where lead
(Pb)-bearing terminations are mandatory and reliability and
stability are of major concern.
TECHNICAL SPECIFICATIONS
TNPW0402
TNPW0603
TNPW0805
TNPW1206
TNPW1210 (1)
0402
0603
0805
1206
1210
Metric size code
RR1005M
RR1608M
RR2012M
RR3216M
RR3225M
Resistance range
10  to 100 k
10  to 332 k
10  to 1 M
10  to 2 M
10  to 3.01 M
DESCRIPTION
Imperial size
Resistance tolerance
± 1 %; ± 0.5 %; ± 0.1 %
Temperature coefficient
± 50 ppm/K; ± 25 ppm/K; ± 15 ppm/K; ± 10 ppm/K
Climatic category (LCT/UCT/days)
Rated dissipation, P70 (2)
Operating voltage, Umax. ACRMS or DC
55/125/56
55/125/56
55/125/56
55/125/56
55/125/56
0.063 W
0.1 W
0.125 W
0.25 W
0.33 W
50 V
75 V
150 V
200 V
200 V
Permissible film temperature, F max.
155 °C
Operating Temperature Range
Thermal resistance (3)
-55 °C to 125 °C (155 °C)
870 K/W
550 K/W
440 K/W
220 K/W
170 K/W
Uins 1 min
75 V
100 V
200 V
300 V
300 V
Continuous
75 V
75 V
75 V
75 V
75 V
Insulation voltage:
Failure rate: FITobserved
 0.3 x 10-9/h
Notes
(1) The detail specification EN140401-801 does not cover this product size.
(2) Rated voltage P x R . The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat
flow support of the printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature is not
exceeded.
(3) Measuring conditions in accordance with EN 140401-801.
Revision: 24-Jan-14
Document Number: 31006
1
For technical questions, contact: thinfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TNPW
www.vishay.com
Vishay
TEMPERATURE COEFFICIENT AND RESISTANCE RANGE
TYPE
TCR
TOLERANCE
RESISTANCE
E-SERIES
±50 ppm/K
±1%
10  to 100 k
E24; E96
47  to 100 k
E24; E192
± 0.5 %
±25 ppm/K
TNPW0402
± 0.1 %
±15 ppm/K
± 0.1 %
±10 ppm/K
± 0.1 %
±50 ppm/K
±1%
±25 ppm/K
TNPW0603
± 0.1 %
±15 ppm/K
± 0.1 %
±10 ppm/K
± 0.1 %
±50 ppm/K
±1%
10  to 1.0 M
± 0.1 %
± 0.1 %
±10 ppm/K
± 0.1 %
E24; E192
47  to 1.0 M
±1%
E24; E96
10  to 2.0 M
± 0.5 %
±25 ppm/K
± 0.1 %
±15 ppm/K
± 0.1 %
±10 ppm/K
± 0.1 %
±50 ppm/K
E24; E192
47  to 2.0 M
±1%
± 0.5 %
±25 ppm/K
TNPW1210
E24; E96
±15 ppm/K
±50 ppm/K
TNPW1206
E24; E192
47  to 332 k
± 0.5 %
±25 ppm/K
TNPW0805
E24; E96
10  to 332 k
± 0.5 %
10  to 3.01 M
E24; E96
47  to 2.13 M
E24; E192
± 0.1 %
±15 ppm/K
± 0.1 %
±10 ppm/K
± 0.1 %
PART NUMBER AND PRODUCT DESCRIPTION
Part Number: TNPW12061K32DETA
T
N
P
W
1
2
0
6
1
K
3
2
D
E
T
A
TYPE/SIZE
RESISTANCE
TOLERANCE
TCR
PACKAGING
SPECIAL
TNPW0402
TNPW0603
TNPW0805
TNPW1206
TNPW1210
R = Decimal
K = Thousand
M = Million
(4 digits)
B = ± 0.1 %
D = ± 0.5 %
F = ± 1.0 %
H = ± 50 ppm/K
E = ± 25 ppm/K
X = ± 15 ppm/K
Y = ± 10 ppm/K
TP
TD
CN
TA
TC
Blank = Standard
0H = Single lot
date code
Product Description: TNPW-1206 1.32K 0.5 % T-9 RT1
TNPW-1206
1.32K
0.5 %
T-9
RT1
TYPE/SIZE
RESISTANCE
TOLERANCE
TCR
PACKAGING
SPECIAL
TNPW-0402
TNPW-0603
TNPW-0805
TNPW-1206
TNPW-1210
Examples:
1K32 = 1320 
99.68K = 99 680 
360 = 360 
± 0.1 %
± 0.5 %
± 1.0 %
T-2 = ± 50 ppm/K
T-9 = ± 25 ppm/K
T-10 = ± 15 ppm/K
T-13 = ± 10 ppm/K
TP1
RT7
R52
RT1
RT6
Blank = Standard
BV20545 =
Single lot date code
Notes
• The products can be ordered using either the PRODUCT DESCRIPTION or the PART NUMBER.
Revision: 24-Jan-14
Document Number: 31006
2
For technical questions, contact: thinfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TNPW
www.vishay.com
Vishay
PACKAGING
WIDTH
PITCH
REEL
DIAMETER
1000
8 mm
2
180 mm/7"
RT7 = TD
10 000
8 mm
2
180 mm/7"
TNPW0603
TNPW0805
TNPW1206
TNPW1210
R52 = CN (1)
1000
8 mm
4
180 mm/7"
TNPW0603
TNPW0805
TNPW1206
TNPW1210
RT1 = TA
5000
8 mm
4
180 mm/7"
TYPE
CODE
QUANTITY
TNPW0402
TP1 = TP (1)
TNPW0402
PACKAGING
STYLE
Tape and reel
cardboard tape
acc. IEC 60286-3
Type I
Note
(1) 1000 pieces packaging quantity is only available for precision resistors with tolerance ± 0.1 %.
DESCRIPTION
RELATED PRODUCTS
The production is strictly controlled and follows an extensive
set of instructions established for reproducibility. A
homogeneous film of metal alloy is deposited on a high
grade ceramic body (Al2O3) and conditioned to achieve the
desired temperature coefficient. A special laser is used to
achieve the target value by smoothly cutting an appropriate
groove in the resistive layer without damaging the ceramics.
The resistor elements are covered by a protective coating
designed for electrical, mechanical and climatic protection.
The terminations receive a final tin-lead (SnPb) on nickel
plating. The result of the determined production is verified
by an extensive testing procedure performed on 100 % of
the individual resistors. Only accepted products are placed
into the tape in accordance with IEC 60286-3, Type I.
Resistance marking is not applied on TNPW0402.
For ordering TNPW with lead free terminations please refer
to
latest
edition
of
data
sheet
TNPW
e3,
(www.vishay.com/doc?28758).
TNPS .... ESCC high-reliability thin film chip resistors are the
premium choice for design and manufacture of equipment,
where mature technology and proven reliability are of
utmost importance.
(www.vishay.com/doc?28789)
ASSEMBLY
The resistors are suitable for processing on automatic SMD
assembly systems. They are suitable for automatic
soldering using wave, reflow or vapour phase as shown in
IEC 61760-1 (1). Solderability is specified for 2 years after
production. The permitted storage time is 20 years.
The terminations are plated with SnPb solder, controlled for
a minimum lead Pb content of 6 % for compliance with the
respective requirements of Bellcore, MIL and ESCC
specifications.
The encapsulation is resistant to all cleaning solvents
commonly used in the electronics industry, including
alcohols, esters and aqueous solutions.
The suitability of conformal coatings, if applied, shall be
qualified by appropriate means to ensure the long-term
stability of the whole system.
Revision: 24-Jan-14
Document Number: 31006
3
For technical questions, contact: thinfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TNPW
Vishay
Current Noise in µV/V
Non-Linearity A3 in dB
www.vishay.com
120
TNPW1206
110
TNPW0805
TNPW0603
TNPW0402
100
90
3
2
1
TNPW0402
0.5
0.3
TNPW0805
TNPW1206
0.1
80
0.05
0.03
70
60
10
100
1K
10K
100K
Resistance Value in Ω
Non-Linearity
0.01
100
1K
10K
100K
1M
Resistance Value in Ω
Current Noise
60
60
[Z]-RO in %
RO
Phase Angle in ϑ°
TNPW0603
TNPW0603
40
20
10 Ω
0
TNPW0603
40
20
10 Ω
0
100 Ω
1 kΩ
100 Ω
- 20
- 20
1 kΩ
- 40
- 40
4.75 kΩ
- 60
4.75 kΩ
- 80
1
5
10
50
100
10 kΩ
500 1000
Frequency f in MHz
10 kΩ
- 80
1
5
10
50
100
500 1000
Frequency f in MHz
HF Performance
60
60
TNPW0805
[Z]-RO in %
RO
Phase Angle in ϑ°
HF Performance
- 60
40
20
10 Ω
0
100 Ω
TNPW0805
40
20
10 Ω
100 Ω
1 kΩ
0
- 20
- 20
1 kΩ
- 40
- 40
- 60
- 80
- 60
10 kΩ
1
HF Performance
Revision: 24-Jan-14
5
10
50
100
500 1000
Frequency f in MHz
10 kΩ
- 80
1
5
10
50
100
500 1000
Frequency f in MHz
HF Performance
Document Number: 31006
4
For technical questions, contact: thinfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TNPW
Vishay
120
Test Voltage in V
Rated Power in %
www.vishay.com
100
80
3K
TNPW0805
1K
TNPW0603
60
100
40
20
EN
0
- 55
- 25
0
25
50
70
Derating
TNPW0805
1K
TNPW0603
100R
1K
10K
100K
Resistance in Ω
100
TNPW0805
^
3K
10R
Single-Pulse High Voltage Overload Test
1.2/50 μs EN 140000 4.27
Pulse Load Pmax.
Note
• The solid line is based on IEC/EN reference test conditions which 
is considered as standard mode. However, above that the 
maximum permissible film temperature is 155 °C (dashed line).
Test Voltage in V
10
75 100
125
150 175
Ambient Temperature in °C
10
TNPW0603
1
100
0.1
10
10R
100R
1K
Single-Pulse High Voltage Overload Test
10/700 μs EN 140000 4.27
10-5
10-4
10-3
10-2
10-1
1
10
Pulse Duration t i
Single Pulse
Maximum pulse load, single pulse;
applicable if P  0 and n  1000 and Û  Ûmax.;
for permissible resistance change equivalent to 8000 h
operation in standard operation mode
Pulse Voltage Ûmax.
100
^
Continuous Pulse Load Pmax.
0.01
10K
100K
Resistance in Ω
TNPW0805
10
TNPW0603
1
500
TNPW0805
400
TNPW0603
300
200
0.1
100
0.01
10-5
Secondary conditions:
a) P see diagram (Pulse Rating)
b) ϑu ≤ 70 °C
10-4
10-3
10-2
10-1
1
10
0
10-5
Pulse Duration t i
Maximum pulse load, continuous pulses;
applicable if P  P (amb) and Û  Ûmax.;
for permissible resistance change equivalent to 8000 h
operation in standard operation mode
Continuous Pulse
Revision: 24-Jan-14
10-4
10-3
10-2
10-1
1
10
Pulse Duration t i
Maximum pulse voltage, single and continuous pulses;
applicable if Pˆ  Pˆ max.;
for permissible resistance change equivalent to 8000 h
operation in standard operation mode
Pulse Voltage
Document Number: 31006
5
For technical questions, contact: thinfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TNPW
www.vishay.com
Vishay
TEST AND REQUIREMENTS
All tests are carried out in accordance with the following
specifications:
IEC 60115-1, generic specification (includes tests)
EN 140400, sectional specification (includes schedule for
qualification approval)
EN 140401-801, detail specification (includes schedule for
conformance inspection)
The testing also covers most of the requirements specified
by EIA/ECA-703 and JIS-C-5201-1. The tests are carried out
under standard atmospheric conditions in accordance with
IEC 60068-1, 5.3. A climate category is applied, defined by
the lower category temperature (LCT), the upper category
temperature (UCT), and the number of days of the damp
heat, steady-state test (56).
Unless otherwise specified the following values apply:
Temperature: 15 °C to 35 °C
Relative humidity: 45 % to 75 %
Air pressure: 86 kPa to 106 kPa (860 mbar to 1060 mbar).
The components are mounted for testing on boards in
accordance with EN60115-1, 4.31 unless otherwise
specified. The parameters stated in the Test Procedures and
Requirements table are based on the required tests and
permitted limits of EN140401-801.
TEST PROCEDURES AND REQUIREMENTS
EN 60115-1 
CLAUSE
IEC 60068-2
TEST
METHOD
TEST
PROCEDURE
REQUIREMENTS PERMISSIBLE CHANGE (R)
Stability for
product type:
TNPW0402
TNPW0603
TNPW0805
TNPW1206
TNPW1210
10  to < 100 
100  to 3.01 M
10  to 3.01 M
4.5
-
Resistance
-
± 0.1 %
± 1 %; ± 0.5 %
4.8.4.2
-
Temperature
coefficient
At (20/- 55/20) °C
and (20/125/20) °C
± 25 ppm/K; ± 15 ppm/K; ± 10 ppm/K
± 50 ppm/K;
± 25 ppm/K
Endurance
U = P 70 x R
or  Umax.;
1.5 h on; 0.5 h off;
4.25.1
at 70 °C
70 °C; 1000 h
± (0.1 % R + 0.02 ) ± (0.05 % R + 0.01 ) ± (0.25 % R + 0.05 )
125 °C; 1000 h
± (0.1 % R + 0.02 ) ± (0.05 % R + 0.01 ) ± (0.5 % R + 0.05 )
4.25.3
-
Endurance
at upper
category
temperature
4.13
-
Short time
overload
U = 2.5 x P 70 x R
2 x Umax.; 2 s
± (0.05 % R + 0.01 ) ± (0.02 % R + 0.01 ) ± (0.1 % R + 0.02 )
4.24
78 (Cab)
Damp heat,
steady state
(40 ± 2) °C;
(93 ± 3) % RH;
56 days
± (0.1 % R + 0.02 ) ± (0.05 % R + 0.01 ) ± (0.5 % R + 0.05 )
4.19
14 (Na)
Rapid change
of temperature
30 min at - 55 °C:
30 min at 125 °C;
5 cycles
± (0.05 % R + 0.01 ) ± (0.02 % R + 0.01 ) ± (0.1 % R + 0.02 )
4.18.2
58 (Td)
Resistance to
soldering heat
-
Flammability,
needle flame
test
4.35
Revision: 24-Jan-14
Solder bath method;
(260 ± 5) °C;
± (0.05 % R + 0.01 ) ± (0.02 % R + 0.01 ) ± (0.1 % R + 0.02 )
(10 ± 1) s
IEC 60695-11-5;
10 s
No burning after 30 s
Document Number: 31006
6
For technical questions, contact: thinfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TNPW
www.vishay.com
Vishay
DIMENSIONS
L
Tt
W
H
Tb
DIMENSIONS AND MASS
H
(mm)
L
(mm)
W
(mm)
Tt
(mm)
Tb
(mm)
MASS
(mg)
TNPW0402
0.35 ± 0.05
1.0 ± 0.05
0.5 ± 0.05
0.2 ± 0.10
0.2 ± 0.10
0.65
TNPW0603
0.45 ± 0.10
1.6 ± 0.10
0.85 ± 0.10
0.3 ± 0.20
0.3 ± 0.20
2
TNPW0805
0.45 ± 0.10
2.0 ± 0.15
1.25 ± 0.15
0.4 ± 0.20
0.4 ± 0.20
5.5
TNPW1206
0.55 ± 0.10
3.2 ± 0.15
1.6 ± 0.15
0.5 ± 0.25
0.5 ± 0.25
10
TNPW1210
0.60 ± 0.15
3.2 ± 0.15
2.45 ± 0.15
0.5 ± 0.25
0.5 ± 0.25
16
TYPE
SOLDER PAD DIMENSIONS
G
X
Y
SOLDER PAD DIMENSIONS
REFLOW SOLDERING
TYPE
WAVE SOLDERING
Y
(mm)
X
(mm)
G
(mm)
Y
(mm)
X
(mm)
G
(mm)
TNPW0402
0.4
0.6
0.5
-
-
-
TNPW0603
0.5
0.9
1.0
0.9
0.9
1.0
TNPW0805
0.7
1.3
1.2
0.9
1.3
1.3
TNPW1206
0.9
1.7
2.0
1.1
1.7
2.3
TNPW1210
0.9
2.5
2.0
1.1
2.5
2.3
Revision: 24-Jan-14
Document Number: 31006
7
For technical questions, contact: thinfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.
Revision: 02-Oct-12
1
Document Number: 91000
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Vishay:
TNPW12066043BR75 TNPW08058250DR75 TNPW06037152BR52 TNPW08051091BR75 TNPW08051491BR75
TNPW06036040DR52 TNPW08051373BR75 TNPW06038060BR52 TNPW06032401BT TNPW06032742BR52
TNPW06035052BR52 TNPW06032321DR52 TNPW12062842BR75 TNPW12062912BR75 TNPW12062982BR75
TNPW12068761BR75 TNPW0603140KBETA TNPW12062743BR75 TNPW06039761BR52 TNPW120612R1FR75
TNPW120620R0FR75 TNPW08054640FR75 TNPW06033163BR52 TNPW06033741BR52 TNPW08052492DT
TNPW12061252BT TNPW060340R2DT TNPW12061762BR75 TNPW08051402BT-T10 TNPW08055051BR75
TNPW06037322DT TNPW08058002BR75 TNPW12061004BR75-T10 TNPW12066343FT TNPW08052343BR75
TNPW08052743BR75 TNPW12065301BR75 TNPW12067501BR75T10 TNPW08056871BR75 TNPW08053052BR75
TNPW08051841BR75 TNPW06036190BR75 TNPW08053240BR75 TNPW06036650BR52 TNPW06031650BR52
TNPW120650R5BR75 TNPW08058060FR75 TNPW06034532BR52 TNPW08053612BR75 TNPW06038250DR52
TNPW06033830BR52 TNPW12061913FR75 TNPW06031912BR52 TNPW080533R2DR75 TNPW08053321DR75
TNPW06031023BR52 TNPW060316R2BR52 TNPW12062103BR75 TNPW08053790BR75 TNPW12069533BR75
TNPW08051743FR75 TNPW060310K7BECN TNPW06033321DR52 TNPW060333R2DR52 TNPW12062130BR75
TNPW08052581BR75 TNPW08054481BR75 TNPW12064931BR75 TNPW12065831BR75 TNPW12067412BR75
TNPW08051093BR75 TNPW08052842BR75 TNPW12062291BR75 TNPW12065691BR75 TNPW12063791BR75
TNPW08056262BR75 TNPW08052260BR75 TNPW060322R1BR52 TNPW12062432FR75 TNPW12063011FR75
TNPW12063740FR75 TNPW12065621FR75 TNPW12065622FR75 TNPW08058660FR75 TNPW08051052BT
TNPW08055491BT TNPW08057591BT TNPW12063092BT TNPW12063650BR75 TNPW060326R1DT-T2
TNPW12062M00BECN TNPW08052672BT TNPW12061013BR75 TNPW08051433BR75 TNPW08054270BR75
TNPW080571R5BR75 TNPW12063090BR75 TNPW06031603BR52 TNPW06033243BR52 TNPW06034641BR52