DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
DVR Series H.264 Digital Video Recorder
User Manual
1
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
PLEASE READ CAREFULLY AND SAVE
This manual contains important information about this product's operation. If you are
installing this product for others, you must leave this manual -or a copy with the end user.
2
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
CONTENT
1 INTRODUCTION.........................................................................................................................5
1.1 Feature.................................................................................................................................... 5
1.2 Product feature.......................................................................................................................5
1.3 Parameter............................................................................................................................... 5
2. ENTIRONMENT ADAPTABILITY............................................................................................8
2.1 Notice:..................................................................................................................................... 8
3. Device operation manual.......................................................................................................... 9
3.1 Remote key instruction......................................................................................................... 9
3.1.1 Remote control..................................................................................................................9
3.1.2 Mouse Operation............................................................................................................10
3.1.3 Menu Configuration........................................................................................................11
3.2 System Operation................................................................................................................12
3.2.1 START-UP...................................................................................................................... 12
3.2.2 SYSTEM LOGIN............................................................................................................ 13
3.2.3GUI OPERATION............................................................................................................13
4. IE OPERATION....................................................................................................................... 33
FEATURE....................................................................................................................................33
4.2 Restriction condition............................................................................................................33
4.3 User login..............................................................................................................................33
4.4 OPERATION INTERFACE.................................................................................................34
4.4.1 LIVE..................................................................................................................................34
4.4.2 PTZ CONTROL.............................................................................................................. 35
4.4.3 ZOOM.............................................................................................................................. 35
4.4.4 Focus............................................................................................................................... 35
4.4.5 Iris..................................................................................................................................... 35
4.4.6 PTZ PRESET..................................................................................................................35
4.4.7 PLAY................................................................................................................................ 35
4.4.8 OTHER OPERATION....................................................................................................36
4.4.9 REPALY...........................................................................................................................36
4.4.10 SETUP...........................................................................................................................38
4.4.11 RECORD.......................................................................................................................38
4.4.12 ALARM SETTING........................................................................................................ 38
4.4.13 PTZ.................................................................................................................................39
4.4.14 NETWORK....................................................................................................................39
4.4.15 System setting.............................................................................................................. 40
4.4.16 HOST INFO.................................................................................................................. 40
5. DVR Installation Guideline..................................................................................................... 41
5.1 Product Overview................................................................................................................ 41
5.1.1 Product Photo................................................................................................................. 41
5.1.2 The Definition of Bottoms and Connectors on Front Panel..................................... 41
5.1.3 The definition of buttons and connectors on rear panel........................................... 42
5.1.4 Connectors for Alarm.....................................................................................................43
3
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
5.1.5 Alarm Input and Output................................................................................................. 43
6. Device Part............................................................................................................................... 45
6.1 Check Device part............................................................................................................... 45
7. FAQ............................................................................................................................................45
4
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
1 INTRODUCTION
1.1 Feature
DVR is 4channel CIF resolution digital video recorder and DVR is 8channnel DVR.
Both of them have local recording, playback, support treble code remote network
surveillance, data backup, parameter setting, motion detection, I/O alarm setting, PTZ and
USB mouse.
1.2 Product feature
�
�
�
�
�
�
�
�
Advanced RTOS
H.264 compression
Software upgrade via USB
USB mouse control
PTZ and network function
Multi-language versions are selectable
Support mobile surveillance
Support network center management system
Applied in large surveillance area such as supermarket, gas station, factory etc.
1.3 Parameter
DVRSeries
Model NO.
4 channle
Operation System
Embedded Linux
Compression
H.264
Video Input/Output
4 channel BNC input/2 channel BNC output
Audio Input/Output
4 channel BNC input/1 channel BNC output
NTSC: 120 fps (4×30 fps)
Display Frame Rate
PAL: 100 fps (4×25 fps)
NTSC: 120 fps (4×30 fps)
Record Frame Rate
PAL: 100 fps (4×25 fps)
Record Mode
Manual﹑Schedule﹑Motion Detection
Image Quality
CIF/HD1/D1 selectable
Record Resolution
704×480﹑704×240﹑352×240(NTSC) 704×576﹑704×288﹑352×288(PAL)
5
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
Playing Mode
1 channel or 4 channel
Searching Mode
By time/By event/By channel
HDD
Support 1TB SATA HDD
Alarm Input/Output
4 channel input/1 channel output
Internet
IE/PPPOE/DDNS
Remote Control
Yes
Mouse Control
USB
USB Port
support USB 2.0
PTZ Control
Yes
Language Support
Simplified Chinese﹑English
7 Inch TFT Monitor
Yes
VGA Output
Yes
Software Upgrade
USB
Mobile Surveillance
Support Symbian s60 v3.0 , Mobile Pocket PC operation system
Power Supply
19V/3.42A DC
Remote Power Supply
Yes
Working Temperature
-10℃ ~ +50℃
Working Humidity
10%~90%
G.W/N.W
3.7KG/2.2KG
Meas(L*W*H)
200×130×230mm
DVR Series
Model NO.
8 channle
Operation System
Embedded Linux
Compression
H.264
Video Input/Output
8 channel BNC input/2 channel BNC output
Audio Input/Output
8 channel BNC input/1 channel BNC output
Display Frame Rate
NTSC: 240 fps (8×30 fps)
6
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
PAL: 200 fps (8×25 fps)
NTSC: 240 fps (8×30 fps)
Record Frame Rate
PAL: 200 fps (8×25 fps)
Record Mode
Manual﹑Schedule﹑Motion Detection
Image Quality
CIF
352×240(NTSC)
Record Resolution
352×288(PAL)
Playing Mode
1 channel
Searching Mode
By time/By event/By channel
HDD
Support 1TB SATA HDD
Alarm Input/Output
8 channel input/1 channel output
Internet
IE/PPPOE/DDNS
Remote Control
Yes
Mouse Control
USB
USB Port
support USB 2.0
PTZ Control
Yes
Language Support
Simplified Chinese﹑English
7 Inch TFT Monitor
Yes
VGA Output
Yes
Software Upgrade
USB
Mobile Surveillance
Support Symbian s60 v3.0 , Mobile Pocket PC operation system
Power Supply
19V/3.42A DC
Working Temperature
-10℃ ~ +50℃
Working Humidity
10%~90%
G.W/N.W
5.0KG/3.2KG
Meas(L*W*H)
200×130×230mm
7
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
2. ENTIRONMENT ADAPTABILITY
2.1 Notice:
For the safely using DVR and prolong device life, please pay attention on following
1.
When installing device, please comply all the electric product safety criterion;
2.
Power and ground:
�
Do not touch the power and DVR with a wet hand
�
Do not drop liquid on DVR
�
Do not put others on DVR
�
Please using soft dry cloth when clean DVR, do not using chemical solvent
�
When the power line connects with jack, even don’t startup device. There is still have
voltage
�
If you do not use device for long time, please take the power line away from jack.
3.
Humidity requirement
Please install the device in good conditions, it’s better to avoid from humidity, drip
sites, etc.
8
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
3. Device operation manual
In device operation, the enter key on remote control has the same function with
mouse left click.
3.1 Remote key instruction
3.1.1 Remote control
Handheld IR Controller Key Functions:
【0-9】keys: During setup, number keys are used to input
values. For viewing channels 1, 2, 3 and 4, use 1, 2, 3 and 4 on
numeric keypad respectively.
【+】,【-】keys: During setup, plus and minus are used to select
next or previous values.
, : Up, Down directional keys: Move selection up and down
in setup menu.
, : Left, Right directional keys: Move cusor left or right in
setup menu.
【QUAD】: Switch 4 Channels;
【FWD】: Fast forward the video while playback. press 【PLAY】to return to normal speed;
【REV】: Reverse the video while playback, press REW to switch, press【PLAY】 to return
to normal speed;
【POWER ON】: Reset the MDVR to Power on and Power off mode. (standby and start
up);
【LOGIN/LOCK】: If the security is enabled in the setup, use LOGIN/LOCK key to enter
the user setup. It is important to remember the password due to without restoration
function. Log in(to enter into “User ID select” and “Password”
input interface)and lock
functions(To exit setup and operation)
【OSD】: Press OSD for main menu;
【PTZ】: PTZ control,press this key to enter into PTZ control interface when at single live
view;
【EXIT】: Exit to the preview or return to the last menu;
9
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
【RECORD】: Start manual record
【STOP】:
Stop manual record
【ASISTANT】For future use
3.1.2 Mouse Operation
You can use mouse to make operation of the menu besides IR remote controller.
(The operation is the same as PC Windows).Please inserts the mouse into USB Port.
Click
Enter into main menu: Click the right key on the live view.
right key
Click the left key to enter into the setting interface.
Click the left key to zoom in the window on the live view and playback video.
Double click the left key can exit to the live view and playback multi-window
interface.
1. Volume adjustment, color adjustment, PTZ setting and VGA border
operation. It is for setting the single channel for volume adjustment, PTZ
control and color adjustment. If it is multi-window, please use the left key to
select the single window.
Click left
key
2. The remark when click the left key for volume adjustment, color
adjustment, VGA border is as follow:
a.There are
and
for buttons the PTZ setting to adjust parameter,
click it can adjust the setting for PTZ.
b.There is a sticker to show the volume on the volume adjustment
interface. Move the mouse to the corresponding position and click the
left key. The right side of sticker will show the volume ,click “x” to exit.
c.Color adjustment can refer to the volume adjustment interface
operation.
When there are many options in the option frame, click left key to see
down-pull menu.
10
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
To click the left key on the playback interface can make >> means forward, <<
means raw, >>I means Slow play, I> means frame play,> means Play, X
means exit.
1. In the input frame, click the left key can activate the keyboard. The number,
symbol, English can be input by clicking the mouse.
2. Pinyin also can be input by the soft keyboard when enter Chinese, the
Click left
method is the same as remote control. You can use the left/right key to turn
key
over the page when check on Pinyin/Chinese word.
3. When input number, click the right key, the number soft keyboard will bob up
firstly, and then use the left key to select the corresponding numerical value.
Also click the left key to exit the number keyboard.
1. Press the left key to move the mouse can adjust the parameter on the
volume, color, VGA border interface. And the corresponding parameter will be
Mouse
display at the same time.
move
2. In the Motion Detection setting interface, you can use the left key to drag the
frame to set the motion detection area.
3.1.3 Menu Configuration
You can control the DVR by a lot of menu operation. This tree will show you the menu
structure and it will be in details in the following chapters.
11
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
3.2 System Operation
3.2.1 START-UP
Connect the power adapter to DVR. When start up the DVR, 【POWER】LED will be
on and 4 images will be display on the screen. If it has setup ignition recording or time
recording, the system will record automatically and the corresponding LED will be on, and
the system work normally.
Remark:
1. If there is no HDD in device, or the device didn’t read the HDD, or the HDD didn’t be
formatted it will display an 【H】 in the video preview interface.
2. You must format the HDD in the DVR before first using. The steps as follows: menu >
12
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
HDD management > format. After formatting, the system will restart.
3.2.2 SYSTEM LOGIN
Remark: default device ID is: 00000, and there is no password. In order to keep safe,
please modify the user password and change the device ID in the base setup. You can
setup user and admin password, Admin has all authorities while user has limited
authorities of viewing image, searching and play backing video. When you input a
password, the system will automatically match and offer different password with different
authorities.
When DVR started, click right key by mouse. If you open a password, it will enter into
user login interface. The picture is as follows:
Ddvice ID
ID: You just need to enter the device ID as the right frame.
Password
Password: enter the admin password or user password.
GUI OPERATION
3.2.3
3.2.3GUI
The main menu include “SEARCH”,”RECORD”,”HDD”,”BASIC”,“ADVANCE”, and “Exit”.
Remark: You must press “APPLY” to make the setting for submenu valid. It will be no use
13
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
when exit directly. There is a special feature of this DVR: when you move the mouse
somewhere, the explanation information will be showed automatically.
1 RECORD SEARCH
Move the cursor to 【RECORD SEARCH】(Icon highlighted when selected),press
【Enter】to enter into the setting interface.
There are three methods of searching record.
Method 1: playback by date
Date input: You can adjust the checking date and time, press【Enter】or input the
number directly to adjust the year, month, date. And then input time in the next box, click
“play” and then you can see the recording video.
Method 2: playback by recording status:
Input the date, click 【search】 and you can see the recording status on this date.
struction:
In
Ins
1. MONTH: It will show all the recording status in this month. Green means normal
recording, Red means alarm recording and the default color means no video. Click
any date in this frame can search the recording status of that day. The searching
result will be showed in the below date frame.
2. DATE: It will show all the recording status in this day, you can playback the record file
in this period via click the corresponding period. Every grid stands for one hour.
Method 3: playback by file list:
Input the searching date, click “SERACH” and you can see the recording status. Click
an exact day and then click “detail file” and then you can see the interface of “detail file”.
CHANNEL: There are CH1, CH2, CH3, CH4 and QUAD, totally 5 options. Press
【Enter】and you can change the channel to be displayed.
14
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
TYPE: There are all, normal and alarm, totally 3 options. Press【Enter】and the
content will be displayed in a list.
Instruction:
1. 【File Detail List】,“Channel” number shows the recording file belong to number
showed channel record. “Recording time” is the recording beginning time to end time.
“SIZE” is the size of this file(Unit: MByte),“TYPE” is the type of recording file.There
are two types: normal and alarm,”Backup” in the lower right corner of menu can
backup the selected files to USB storage;
2. Moving the cursor to select the files, and press【OK】to enter into playback interface。
If more than one channel have recording files during selected time, will playback all at
the same time;
3. If let【RECORD TIME】available in 【BASIC SETUP】,it will show the date/time when
playback record file;If 【RECORD TIME】available , it will not show the time;
4. When playback, press【SLOW】to let the playback slow;press【FORWARD】、
【REVERSE】to speed、reverse play; press【PAUSE/STEP】to pause or playback
frame by frame;Press【Exit】to exit from playback and return to the Previous menu;
5. When selected recording file playback finished, it will continue following files; if no
followed record file, it will return to 【File Detail List】 automatically
2. BACKUP
Via USB Storage to backup, connect USB device via USB2.0 port before backup.
Select the recording file by direction keys , and press【Enter】, There will a “√” sign if
select is ok, and then press【BACKUP】to begin backup as follow:
15
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
Instruction
Instruction:
1. When USB device space is less than recording file, the system will show “Space no
enough”.
2. Disconnect USB device directly when backup finished.
3 RECORD MODE
Move the cursor to 【RECORD】(Icon highlighted when selected),and press【Enter】
to enter into the setting interface(As follow showed). use direction keys and cursor to
change the options.
CHANNEL: ON: Means the channel enable for recording.
RESOLUTION
RESOLUTION:: There are HIGHEST, HIGH, NORMAL three options, HIGHEST means
the resolution best , corresponding to D1、HD1、CIF resolution.
QUALITY : There are BEST, FINE and NORMAL three option, They are corresponding
HIGHEST, HIGH and NORMAL data stream standard
AUDIO: ON: Means enable the audio recording for all channels, OFF: Means disable
audio recording
REC.MODE
POWER UP: Means recording start when DVR to work.
16
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
TIME: Recording as the schedule. When chose Time recording, 【Recording period
setting】will show up in the right. Move cursor to there, and press 【Enter】to the interface
as below:
CHANNEL: You can select all channel or just one channel
DAILY: There are ALARM, NORMAL, NO REC three modes, if set for detail time, please
set in 【Recording period setting】 and then press 【Enter】. Impress color means no
recording during this time. Different color means different recording mode: Red means
alarm recording, green means normal recording, blue means no recording.
RECORD SIZE: Press 【Enter】 or 【+】/【-】to choose the record size time.
There are 15min, 30min, 45min, 60min four options, that means it will pack as the
mode you selected
4 Hard Disk Management.
Move the cursor to 【HDD】(Icon highlighted when selected),press【Enter】to enter into
the setting interface, and you can use direction keys and cursor to change the options.
HDD STATUS: There are three status available, normal, un-format, No HDD. If HDD can
not run normally(including unformed and no HDD), there is a 【H】display on video
17
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
preview interface.
OVERWRITE: ENABLE: means when HDD space is less than 4G, it will delete earliest
recording file, deleting can stop until the space is no less than 10G; DISABLE: means
when HDD space is less than 500M it will stop recording, and an prompt will display
“please shutdown and replace HDD”
FORMAT: Move cursor to select device and press【APLLY】 to format
FORMAT Flash Disk: Move cursor there to select device and press【APLLY】 to format
Note: DVR system will restart after HDD formatted, but no restart for U Flash disk format.
5 BASIC SETUP
Move cursor to select “BASIC SETUP” (The big icon means select ok)and press
【ENTER】to enter into the system language setup interface.
Basic setup includes language, date/time, password, display, and video/audio and
exit six options.
6 SYSTEM LANGUAGE SETUP
Move cursor to select “system language” (The big icon means select ok)and press
【ENTER】to enter into the system language setup interface.
18
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
There are Chinese and English options, press【ENTER】or【+】/【-】to chose.
Remark: System will restart after changing language success.
7 DATA/TIME SETUP
Move cursor to select “date/time” (The big icon means select ok)and press【ENTER】
to enter into the date/time setup interface.
DATE: Press【Enter】or 【+】/【-】or press number key to chose the date.
DATE FORMAT: Press ENTER to switch between the date patterns, there are
YY-MM-DD and MM/DD/YY two options. When chose the date format, left date will be
displayed with corresponding format.
TIME: Press【Enter】or 【+】/【-】or press number key to choose the date.
TIME FORMAT: Press ENTER to switch between the date patterns, there are 12 HOURS
and 24 HOURS two options. Left time will be displayed with corresponding format.
Remark: Have to move the cursor to the 【MODIFY TIME AND DATE】 and press
【APPLY】 to save it, otherwise it won’t save the modify if you exit this interface.
19
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
8
SECURITY
Move the cursor to【SECURITY】(Icon highlighted when selected), press【Enter】
to enter into the setting interface.
DEVICE ID: Press 【+】/【-】or number key to setup the ID
PASSWORD: 【Enter】 key to choose whether password enable or disable. ”enable”
means user
need insert password when log in, “disable” means without password and user can enter
into main menu directly.
USER PASSWORD: Press number key to setup.
ADMIN PASSWORD: Press or number key to setup.
9 DISPLAY SETUP
Move the cursor to【BASIC SETUP】(Icon highlighted when selected), press【Enter】
to enter into the setting interface.
NAME: press【Enter】to enter into the setting interface.
POSITION: press【Enter】to switch name location, there are 5 options: bottom left, top left,
20
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
bottom right, top right and OFF.
COLOR: press【Enter】to enter into setting interface, as following:
Press【Enter】or directly drag the cursor to set colors, including chromaticity,
luminosity, contrast and saturation, press【APPLY】to save the parameters.
PREVIEW: ON: Means the channel is allowed to view the live mode
PREVIEW TIME: ON: Means displaying system date and time above video.
RECORD TIME : ON: Means clock will display in the playback of current file
EO
/AUDIO SETUP
10 VID
VIDEO
EO/AUDIO
Move the cursor to【VIDEO/AUDIO SETUP】(Icon highlighted when selected),
press【Enter】to enter into setting interface.
11 ADVANCE SETUP
Move the cursor to【ADVANCE SETUP】(Icon highlighted when selected),press
【Enter】to enter into setting interface. Picture is below:
21
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
Advanced Function include Alarm settings, system information, Motion detection,
mobile phone monitoring, system maintenance, PTZ and network setting.
12 ALARM SETUP
Move the cursor to【ALARM SETUP】(Icon highlighted when selected),press【Enter】
to enter into setting interface. Picture is below:
I/O ALARM
ALARM:: Each channel corresponds an I/O status, that is, when an alarm triggered,
it will activate the corresponding channel to start alarm recording.
N.O: indicate alarm is always OFF; it will be ON when have alarm
N.C: indicate alarm is always ON; it will be OFF when have alarm
HDD LOSS: turn on means it will trigger an alarm if there is no HDD, and it will display an
【H】
On the bottom left of channel 1 in the live view
HDD SPACE: turn on: If the space is less than 500M, there is a remark in live view: No
enough space, please change HDD after shutdown.
VIDEO LOSS: turn on: when one channel has no video input, it will display “video loss”in
live view.
22
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
ALARM MANAGE: There are alarm output, buzzer and post REC.
OUTPUT
OUTPUT:: when an alarm triggered, the alarm output time will be:
0 second、10 seconds,20 seconds,40 seconds or 60 seconds
BUZZER: buzzer calling time setup when alarm triggered: 0 second,10 seconds,20
seconds,40 seconds or 60 seconds
POST REC.: post recording time setup: 30 seconds,1 minute,2 minutes or 5 minutes
13 SYSTEM INFO
Move the cursor to【SYSTEM INFO】(frame is red when selected),press【Enter】
to enter into system info interface, on this interface mainly display system hardware
features and firmware version, include: software version, MAC address、serial number.
Picture is below:
14 MOTION DETECT
Move the cursor to【MOTION DETECT】(Icon highlighted when selected),press
【Enter】to enter into motion detect setting interface. Picture is below:
CHANNEL SWITCH
SWITCH:: Each channel has corresponding channel switch, press 【Enter】to
23
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
turn on or turn off the motion detection for each channel..
SITIVITY: each channel has corresponding sensitivity setting, including four
SEN
ENSITIVITY:
standards high, relative high, medium and low, press【Enter】key to switch
MD AREA:
each channel has corresponding regional motion detecting setting, move the
cursor to corresponding【setting】,press【Enter】to enter regional setting interface, red
area means it have activated motion detection, transparent block means it have not
activated motion detection. Picture is below:
Move the direction key on remote control or make cursor move to the need designed
area, green frame means the cursor has moved to this pane, press【Enter】to select or
cancel motion detection of this small pane, when setup finished, press【exit】to back to MD
setup interface, it will save automatically.
Remark:
IR Operation: press [Menu] key to select or cancel full screen.
Mouse operation: click left and drag the frame to setup the region for motion detection.
15 Mobile Surveillance
Move the cursor to【MOBLE】(Icon highlighted when selected),press【Enter】
to enter into setting interface. Picture is below:
24
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
NETWORK CHANNEL: select the channel for network transfer, and press [Enter] to
switch different channels.
WIRELESS NETWORK: Select different mobile network from the options of 3G, 2.5G and
2.75G, and press [Enter] to switch different network.
NOTE: Detail setting up please refer to appurtenance.
16 SYSTEM PROJECT
Move the cursor to 【SYSTEM PROJECT】(Frame turns red means selected), and
press【Enter】 to enter into system project setup interface. Picture is below:
AUTO RESET
RESET:: When switch is on, you can setup the time for device to restart.
SYSTEM UPDATE: Copy the update file to the root directory of the flash disk, and insert it
into USB groove, then press [Enter] to upgrade the firmware, and it will display the
process of the system upgrading, picture is below:
25
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
DEFAULT SETTINGS: Restore all the settings as the factory setting.
NOTE: make sure that the U drive and power is steady when it is upgradeing.
17 PTZ SETUP
Move the cursor to【PTZ SETUP】(Icon highlighted when selected),press【Enter】
to enter into setting interface, you can setup the parameters for each channel separately.
With direction key or move cursor to the option, and press [Enter] to switch different
channels.
CHANNEL: The channel of PTZ connected.
PROTOCOL: select the protocol of different PTZ, there are two protocols to switch, and
the default is Pelco-D
BAUD RATE: select the different baud rate for your PTZ, there are 1200, 2400, 4800, and
9600
DATA BIT: there are 5,6,7,8 options to select, default setting is 8.
STOP BIT: 1 and 2 are optional, the default setting is 1.
VERIFY: there are None/Odd/Even/Mark/Space to select, the default setting is none.
ADDRESS: Fill the code of respective PTZ with relative channel.
26
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
18 NETWORK SETUP
Move the cursor to [NETWORK SETUP] (icon thighlitend when selected), and press
【Enter】 to enter into setting interface .picture is below:
CONNECT NETWORK TYPE: There are PPPOE, DHCP & Static three options
� 1 Static
Select [Static] in the CONNECT NETWORK TYPE, and press [Enter] to enter into
the interface as followings
MEDIA PORT
PORT:: transfers video data between client and device.
WEB PORT: setup the port of IE browser via HTTP.
IP ADDRESS: setup the IP address, and press [Enter] 【+】/【-】 or input numbers
to fill IP address.
NETMASK:
NETMASK:.press [Enter] 【+】/【-】 or input numbers to fill netmask.
GATEWAY: press [Enter] 【+】/【-】 or input numbers to fill default gateway.
� 2 DHCP
Select the DHCP, and enter into the interface as followings.
27
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
MEDIA PORT
PORT:: same as static setup
WEB PORT: same as static setup.
NOTE: restart system when select DHCP, and it will automatically connect with
DHCP server. Will allot IP address when connect ok and the address will showed on
the interface.
� 3 PPPoE
Select the PPPOE, and enter the interface as followings:
MEDIA PORT
PORT:: Port for private protocol of DVR and PC, default : 9000. If this port of
computer is applied by other server, please change to other free port.
WEB PORT: Http port. Default: 80. If admin change WEB port to: e.g. 8088, port No.
should be added behind IP, http://192.168.15.145:8088 should input into IP of IE.
IP address: Fill in IP address according to the net of DVR;
Net mask: Fill in net mask according to the net of DVR.
Gateway: According to the net of DVR, set gateway. If no router of the net, please
distribute IP address of same web segment; corresponding gateway should set .
28
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
19 Application of DDNS
You should register a host name, user name and password from DDNS manufacture,
now we take dyndns for instance, to show you how to register.
Please type in the IE address as follow: http://members.dyndns.org/ to register a new
user
1. Fill out all the information then submit.
2. Minutes later, you will get a mail from dyndns, which include the primary password for
the user you just register.
3. Then please login http://members.dyndns.org/ with the new user and password, click
“domain name management” to enter into the operating interface, then select “new”
under the Dynamic DDNS.
4. Create a domain name you need, then press to apply; now you have registered a host
name success.
20 DVR group network
This chapter mainly narrates some networks’ setting method for your reference:
Applied ADSL
only one DVR need to connect with Internet
1.Applied
ADSL,only
1. Make sure the DVR has successfully connected to ADSL modem; the LED is flashing
means success.
2. Network type: PPPoE
3. Input media port and web port. Please refer to“Setup instruction”network setup;
29
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
4. Type in the PPPoE user name and password;
5. Fill in DNS IP,such as:202.96.128.166 or 10.95.0.3. Users can refer to local computer
DNS setup,(in DOS input ipconfig/all in DOS to query);
6. Since the public IP will change after restart, please use DDNS function, and mapping
the public IP to a fixed domain name.
7. Save and restart device, it will connect to internet via PPPoE mode automatically, if
success, it will got a dynamic public IP.
8. ping xxx.xxx.xxx.xxx(The public IP of DVR) to check whether the network is ok, and
ping xxx.xxx.xxx(the domain name of DVR)to check whether the DDNS settings is ok.
9. Open IE browser, and type in the domain name of DDNS (if WEB port is not 80, you
should add a port, please refer to IE setup)
10. Please download the IE control, then enter into login interface, the default setting has
no password. Press enter and into the preview interface, and do what you want
according to your need.
2. Applied ADSL, many types of equipment should share and connect with internet
1. Need to confirm with internet manufacture, the ADSL you applied should permit multi
share of the internet.
2. You should buy a router, currently many small routers of 4 port Hub is in the market; or
your ADSL Modem has router function;
3. Refer to router user manual to ensure equipment connection correct;
4. Start PPPOE function of PPPOE, use router to have ADSL;
5. Suggest stopping router’s DHCP function. DVR and the computer all adopt IP. Notice:
30
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
DVR, computer and router’s IP must in the same subnet, and the sub mask, gateway,
DVR internet setting:
Computer internet setting:
6. Operate normal data via computer. This can check if above setting is correct;
7. Input IP address to check if it can visit DVR
8. Add DVR’s port transfer function. Add DVR’s media port and WEB port
9. Use internet remote PC. Check if DDNS is successful via ping xxx.xxx.xxx (DVR ‘s
domain name)
10. Input DDNS into IE address, if the WEB port is not 80, port number should add.
Please refer to IE operation chapter;
11. After downloading IE active tool successfully, login the interface, default is no
password, press OK to enter preview interface and have your following operation.
3 Manufacture has applied Internet line, DVR should connect with internet via IP
and router.
1. Make sure DVR connect with the internet is correctly;
31
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
2. Use still configuration mode;
3. Please refer to internet setting chapter of “Installation guide”, it can help to set port
number, IP address, sub mask, gateway, etc;
4. Net admin add DVR port transfer or sending relation in router;
5. Use a computer of LAN, input IP of LAN and port number into IE address column to
visit the DVR;
6. Use internet remote computer, input IP and port number of router to IE address
column to visit DVR; you can start DDNS function. After finishing DDNS register and
setting, users can visit via DDNS and port number. This can avoid remembering
complex IP.
32
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
4. IE OPERATION
FEATURE
Through the IE browser of OS and install the software, you are able to do the network
operation remotely, which is much more convenient. DVR support C/S, B/S, and visit in
LAN and WAN, also support IP and domain name visiting.
It supports users revise server port. At the same time, it supports PPPOE, DHCP and
four channel video / audio.
4.2 Restriction condition
To ensure PC‘s stable visiting of DVR, recommend Windows XP, Windows Vista
operation system, recommend browser as IE 6.0, IE 7.0.
4.3 User login
Input the DVR local IP in IE browser, if the web port number is set as 80, directly input
IP address into IE address column; If not 80, port number should add behind IP. E.g.
when IP is 192.168.0.102, set port is 8088, http://192.168.0.102:8088 should input.
When the net is connected, IE will automatically download the file to PC as following,
The process will last for 1~2 minutes.
Please click “If your browser does not support the ActiveX to download, please click
here”when downloading not successful.
System will automatically enter GUI as follows:
33
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
Chinese/English selectable.
PASSWORD: Administrator has all authorities, operator has limited authorities who they
can only watch, playback, please change the unit No. and default password in time for
system security.
NETWORK: LAN/WAN, according to the net type of your computer and DVR.
Click“Login” to enter IE interface. If input is wrong, click “Reset” to delete and rein put.
4.4 OPERATION INTERFACE
There are Live view, Playback and Setup options in the main interface, please press
them to access it.
4.4.1 LIVE
Click
to enter into the interface as followings
34
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
4.4.2 PTZ CONTROL
Change the focus, preset aperture to control the PTZ.
Click
to up/down/left/right control movement of the PTZ. When hold on
the one direction key, the PTZ will keep circling as that direction after user press the stop
key in the center of the wheel.
4.4.3 ZOOM
Click
to zoom in and out.
4.4.4 Focus
Click
to focus
4.4.5 Iris
Click
to change the size of aperture
4.4.6 PTZ PRESET
Setup preset point.
You can control it via the below three buttons:
4.4.7 PLAY
Move cursor to the icons, it will highlighted when selected
Open all video
Capture picture, save in local disk, system save default route is C:/DVR
Quickly start all channels’ recording video, here the left up corner of each channel
have normal recording video symbol 【R】, click icon to switch between signal
screen
/quad
/nine
/16 split
.
Volume adjust button
35
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
4.4.8 OTHER OPERATION
1. Select one channel at preview screen (the selected channel’s frame will be change to
RED), double click left key, enter to the selected channel single screen display.
2. Click one Chanel via left key at preview screen, then click right key, will occur window
shortcut Menu, see below picture
You can open, shut down and start this channel’s record via shortcut menu.
3. Click right key at one live view screen, click” open all windows” or “ close all windows”,
will quickly open/close all windows.
4.4.9 REPALY
Click” REPLAY” to enter into playback interface.
Click right up of calendar interface
and
, to setup the month for searching,
click” refurbish”, at the calendar interface will display the recording information of current
month
36
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
The highlighted date means that day have recording video, RED FRAME means the
date is system date, click the date will search that days’ recording file list. For example,
the above picture display 2008, Dec. 3rd,4th,5th,6th,8th,9th,10th,11th,12th,17th,18th
have recording video, and system date is 18th, Dec, 2008, currently search date is 17th,
Dec.
At the below of calendar select channel and type, click SEARCH, the result will
display, as follow.
Double click one item of listed recording video, the recording video will playback,
meanwhile the file icon will change to
, and will occur the below picture play buttons:
The above purple progress bar shows download progress, green progress bar shows
37
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
playback progress
Switch between pause/play
Stop play
Fast play
Slow play
Pause at next frame
Convert H.264 file to H.avi file, click this button access into file convert setting
interface, as follow.
SOURCE FILE: Click
DESTINATION FILE: Click
After setting, click
to setup the H.264 file to convert
to setup the directory for saving avi file
, file convert start, the convert progress bar (see below
picture) will see the progress of convert.
4.4.10 SETUP
Click “SETUP” to enter into setup interface, this interface include record, alarm, PTZ,
network, setting and system information six menus.
4.4.11 RECORD
Click “RECORD” to enter into setup interface; you can check the parameter settings
as in GUI of DVR.
4.4.12 ALARM SETTING
Click “ALARM” to enter into setup interface; you can check the parameter settings as
in GUI of DVR.
38
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
4.4.13 PTZ
Click “PTZ” to enter into setup interface; you can check the parameter settings as in
GUI of DVR.
4.4.14 NETWORK
Click “NETWORK” to enter into setup interface; you can check the parameter settings
as in GUI of DVR.
39
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
4.4.15 System setting
Click” SETUP” to enter the system setting interface as follows:
BANDWIDTH: Set the amount of bandwidth in kbps (128k、192k、256k、384k、512k、
1024k) that you want to allocate for traffic that matches internet,this bandwidth depends
on the place, normally around 256 or 384 kbps.
FILE SAVE PATH: capture picture and recording video save path.
IE login password and DST settings you can check as DVR setting.
4.4.16 HOST INFO
Click “HOST INFO” to enter into system information interface (see below picture), this
interface shows HDD status, remain record time, firmware version, MAC Address, and all
the information is fixed.
40
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
5. DVR Installation Guideline
5.1 Product Overview
1 Product Photo
5.1.
5.1.1
5.1.2 The Definition of Bottoms and Connectors on Front Panel
NO.
TYPE
NAME
direction key include: up【
Direction key
right 【
】、down【
】、left【
】、
】four buttons, which can move cursor to setup
and control PTZ.
Confirm operation, or into PTZ control panel under live
OK/PTZ(OK/PTZ)
view
Stop
Control
key
【■】Stop button
Speed choice
【
】fast forward button、【
】fast reverse button
Pause key
【‖】pause key
Single image
CH1、CH2、CH3、CH4 single image choice
playback
【
button
】PLAY recording playback button
41
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
IR receiver
MENU/EXIT
Enter into main menu under live view, or exit sub menu
HDD
HDD Status
POW
power
IR
Remote control receiver
5.1.3 The definition of buttons and connectors on rear panel
Item
Physical connector
Connector description
1
POWER input
DC 19V/4A
2
Power switch
host power switch
3
Video output
Two video output for connecting TV or monitor (BNC)
4
Video input
For connecting analog video signal input (BNC)
5
Audio Input
For connecting audio signal
Alarm Input
I/O alarm input, 4 for 4CH DVR and 8 for 8CH DVR
Alarm Output
I/O output for alarm
RS485
RS 485 for connecting PTZ
RS232
For connecting PC
6
42
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
Power supply for DC relay and the current is 100MA
+12V
(make sure short circuit can not happen)
7
Network
For connecting Ethernet
8
VGA output
For connecting VGA monitor
9
USB2.0
Copy video record via USB2.0
10
USB MOUSE
Mouse operation equipment
11
audio output
For connection audio output
12
Fan
Please check the fan function for diary maintained and
change new one if the fan has some problems
5.1.4 Connectors for Alarm
Peel off the color skin of the cable and then insert the cable into the slot on the rear
panel DVR.
5.1.5 Alarm Input and Output
There are 8 sets alarm input connector and 1 set output for this DVR. Alarm input is
for connection IR annunciation, fog sensor. The connection diagram of DC alarm inout as
following:
43
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
Connection diagram of AC alarm input as following:
12V
220V AC
24V
RELAY
DVR I/O output
The connection diagram of alarm output as following:
44
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
6. Device Part
6.1 Check Device part
1. Digital Video Recorder 1 SET
2. Standard Part
7. FAQ
If your problem is not in below, call our hotline and we will resolve any issues or
problems you may have.
1.
Question: Why DVR can
can’’t work after starting it?
Answer:
� Check the adaptor input
� Check the on-off power line, does it well-connected?
� Check the on-off power
� Check the upgrade procedure whether it’s wrong
� Check the main board of DVR whether it’s ok
45
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
2.
Question: Why DVR will automatic reboot or stop after starting DVR several
minutes?
Answer:
� Instability or low input voltage
� Bad track hard drive or the line of hard drive is bad
� On-off power supply is not enough
� The front-end video signal instability
� High temperature, too much dust, too bad the DVR operating environment
� The main board is not well-connected with other board
� The hardware of DVR is fault
3.
Question: Why there is no output of single channel, multi channel or all
channel video?
Answer:
� Please check the adaptor of camera whether it is well-connected
� Please check the connect line for connecting video input and video output in
the back board of DVR
� Please directly insert the video source into the display device, and check
whether the video source and display device aspect of the problem.
� Check the brightness of the picture is 0, and bring it back to its original
default setting
� No video input signal or too weak
� Display settings in the preview set to be closed
� The hardware of DVR is fault
4.
Question: Why the DVR can
can’’t record after startup and the interface shows “H”?
Answer:
� Check the DVR whether it use by DC 19V power adaptor
� Check the HDD whether it is formatted in DVR
� Check the HDD power line and the data line whether they are
well-connected or badly
� The HDD has problem
46
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
� The SATA port has problem
5.
R”“M
M”“II”“H
H” showed in interface?
Question: What is meaning by
by“R
Answer:
� “R”means the channel is recording
� “M” means the channel is being motion detection
� “I”means the channel is being alarm
� “H”means there is no HDD, the HDD is bad or the space of HDD is full
6.
Question: Why DVR has the problem of real-time image, such as video image
color, serious bright distortion?
Answer:
� BNC output, selectable PAL and NTSC is not correct, the image will be
black and white
� DVR does not match with monitor
� The video transmission distance is too far
� The setting of dvr color , brightness and so on are wrong
7.
Question: Why there is no voice when monitoring?
Answer:
� Check if it is using positive sound box or speaker, users can have short
circuit to check.
� Is activation of the audio source connected to the video channel? You can
click to full-screen to determine.
� The hardware of DVR is fault
8.
Question: Why there is no voice when playing back?
Answer:
� Setting problem: open audio-video item
� Check the audio whether it is closed in playback interface
9.
Question: Why the system time is not right?
Answer:
� Setting wrong, or users didn’t click “Edit” to make it validity
� Battery not connected well
47
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
� The battery is invalid. Please change one.
10. Question: Why DVR can
can’’t control the PTZ?
Answer:
� The front-end PTZ is fault
� The PTZ decoder setting, connecting and installing is not correct
� The connect is not correct
� The PTZ setting of DVR is not correct
� The PTZ decoder does not match with the DVR agreement
� When connecting multi decoder, 120 Ω electric resistances should add at
the end of PTZ decoder AB line, or else PTZ will not be stable.
� The distance is too far
” by the right mouse button does not work,
11. Question: Why the “Stop recording
recording”
how to stop recording?
Answer: :
� The “Stop recording” by the right mouse button is only suitable for Manual
recording. It can’t stop recording when it’s in “start recording” or the video in
video plan.
� If you want to stop recording, please set the time is not recording.
12. Question: How much space of HDD for recording per hour?
Answer:
� Each channel takes about 14Mbyte for audio recording
� HDD space cost is related with “Best, Good, Middle” in “Record mode>Bit
rate” and the video size of the period. If the video is still, HDD cost will be small; if the
video is moving, HDD cost will be large. “Best” will take 320Mbyte of each channel
per hour; “Good” 50~100Mbyte of each channel per hour when video is still or few
moving, 100~200 M byte of each channel per hour when video has big moving or
much moving; “Middle” 50~100Mbyte of each channel per hour when video is still or
few moving, 100~150 M byte of each channel per hour when video has big moving or
much moving.
13. Question: Why it can
can’’t do motion detection?
48
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
Answer: :
� The setting of the area of motion detection is not correct.
� Low sensitivity
/USB backup error
14. Question: CD-writer
CD-writer/USB
Answer:
� The data exceeds the capacity of backup device
� The backup device is incompatible
� The backup device is damaged
15. Question: Why I/O alarm does not work?
Answer:
� The alarm setting is not correct
� The alarm line connection is not correct
� The alarm input signal is not correct
� An alarm device connect two-loop access at the same time
16. Question: Why remote control can
can’’t work?
Answer: :
� The address of remote control is not correct
� The distance of remote control is too far or the angle is too biased
� Remote control batteries run out
� Remote control is damaged or the front panel of dvr is damaged
17. Question: Why WEB can
can’’t log?
Answer:
� Please check the network whether it’s connected. And check if the panel
LINK or 100M LED display normally; use ping xxx.xxx.xxx.xxx (DVR IP) to
check if the internet is well linked.
� Recommended Windows XP or Vista operating system, using IE6.0 browser
or IE7.0 browser
� ActiveX control is been blocked. Please manual install ActiveX control.
� Please install DX8.1 and upgrade your video card driver
18. Question: There is no picture or not clear when you preview the recording or
49
DVR Series H.264 Digital Video Recorder User Manual ………………………………………………….V1.0
playback the recording by IE?
Answer:
� If you visit DVR by IE, please choose “Wan” in “web environment”
� Please try to “Close windows” by the right mouse button, and try to “Open
windows”
……” While setting DVR
19. Question: Why it displays “ other members are setting
setting……”
by IE?
Answer:
� Please check the DVR configuration interface is in the state of open. Please
exit DVR.
50