64-0048-02

Dialogic®
D/4PCIU,D/4PCIUF
Quick Install Card for PCI Universal
Part Number 64-0048-02
Copyright © 2003-2007
Dialogic Corporation.
All Rights Reserved.
Before You Begin
Protecting the Board from Damage
CAUTION
All computer boards are sensitive to
electrostatic discharge (“ESD”). Handle all static-sensitive
boards and components at a static-safe work area, and observe
anti-static precautions at all times.
If you are not familiar with ESD safety precautions, visit
http://www.dialogic.com/support/hwinstall to learn more.
Unpacking the Board
®
Unpack the Dialogic D/4PCIU, D/4PCIUF board (“board”)
according to the following steps:
1. Prepare a static-safeguarded work area.
2. Carefully remove the board from the shipping
carton and anti-static packaging. Handle the board
by the edges and avoid touching the board’s
components.
3. Lay the board on the static-dissipative work
surface.
Note: Place boards in static-shielding bags when carrying
boards from station to station.
NOTE: If the chassis power is off, callers hear ringing
(on-hook).
Board Identification
®
The Dialogic D/4PCIU board uses Plug and Play
technology, including hardware auto-configuration for IRQ
and memory address. This technology enables quick
installation and operation using the factory default hardware
settings.
CAUTION: Do not remove the board from the anti-static
packaging until you are ready to install it. Observe proper
anti-static precautions at all times.
The system software assigns board instance numbers in
ascending order (beginning with 0) as it detects each board in
your system. A board instance number is the identification
(ID) number used by the system software to recognize the
board. Each Board ID is based on the SW30 rotary switch
setting. See the Physical Description section.
Configuring the Hardware
NOTE: The ascending Board IDs automatically assigned by
the system may not correspond to a physical order in the
chassis.
Initial Hook State
The position of slide switch SW4 determines how the board
responds to an incoming call when the chassis power is on but
the board is not initialized. Refer to the Physical Description
section. Set the SW4 slide switch as follows:
SW4 = On-hook (default): Callers hear ringing.
SW4 = Off-hook: Callers hear a busy signal.
Geographical Sequence
Leave SW30 set to Board ID 0 (default) to let the system
automatically assign board instance numbers by PCI bus
logical slot number. This method is not available for ISA bus
boards.
NOTE: If you add or remove a board, the system may
change the existing board instance (ID) numbers.
Programmable Sequence
You must set SW30 to a unique number for each installed
board. Use a non-metallic screwdriver to turn SW30 to 1 of
16 board settings, 0–9 or A–F. You should assign sequential
numbers to each Dialogic® board, starting at 1. This method is
also used for all ISA bus boards.
Precedence in Mixed Systems
In systems where both ISA and PCI boards exist, PCI boards
take precedence and are numbered before ISA boards. Also,
when using both geographical and programmable assignment
methods, PCI boards that use SW30 setting 0 are numbered
before PCI boards that use SW30 settings 1–9 or A–F.
NOTES: After the hardware and the system software are
installed in a Windows system, refer to the Dialogic®
Configuration Manager (DCM) utility to retrieve the assigned
board instance (ID) number(s). After the hardware and the
system software are installed in a Linux system, refer to the
proper configuration files to retrieve the assigned board
instance (ID) number(s).
Connecting Cables to J1-J4
Pinouts for J1–J4
on Bracket
Installing the Hardware
2. Remove the computer cover.
3. Select an empty PCI expansion bus slot and remove the
slot’s retaining screw and access cover plate.
4. Insert the edge connector of the board into the bus slot.
Press firmly until the board is securely seated.
Installing the Universal PCI Board
Remove
Cover
Plate
PCI
Board
Computer
Chassis
1
2
3
4
5
6
UNUSED
UNUSED
Ring
Tip
UNUSED
UNUSED
Pin 1
NOTE:
J1 is Channel
J2 is Channel
J3 is Channel
J4 is Channel
1
2
3
4
After Installing Hardware
After installing the hardware, run the Dialogic® Configuration
Manager (DCM) as described in the installation instructions
included with the Dialogic® System Software to configure
your system.
For technical specifications and product information go to:
http://www.dialogic.com/products.htm.
Warranty
PCI Slot
ISA Slot
5. Replace and tighten the retaining screw to secure the
board firmly in the chassis slot.
6. Replace the computer cover when finished and
reconnect the power cords.
7. Turn the power to the chassis ON.
CAUTION: If your BIOS is set to use Plug and Play
technology and there are ISA boards in your system, an
IRQ conflict can be created if a PCI board is assigned the
same IRQ as an ISA board. This could cause the machine
to stop responding. You can prevent this by entering the
BIOS and reserving the appropriate IRQs (those used by
your ISA boards) for ISA use only.
Connecting External Cables
Each RJ-11 jack on the rear bracket of this board supports a
single channel. Use RJ-11 connectors and telephone cable to
connect each channel jack to a PBX station port or to the
Public Telephone Network Central Office (CO).
NOTE: A standard telephone will not function when directly
connected to the board.
Sales Assistance
If you have a sales question, please contact your
local Sales Representative or the Regional Sales Office
for your area. Address, telephone and fax numbers, are
available at the Dialogic website located at:
http://www.dialogic.com/contact.htm.
1
2
3
4
5
6
NOTE: If you are adding Dialogic® hardware to an existing
system, you do not need to uninstall existing system software.
1. Working with your computer at a static-safe work area,
switch off the power and disconnect all power cords
from the electrical outlets.
PBX or Public Telephone
Network Cable Connector
and Return Information
Warranty Period
For specific warranty information for this board, refer to the
Warranty section of the Products page, located at this URL:
http://www.dialogic.com/warranties/.
Contacting Technical Support
Dialogic provides technical support for its products through a
network of value added distributors who are trained to answer
technical questions on installing and configuring Dialogic®
products. If you are unsure how to contact your support
channel, please call Dialogic n the United States at 973-9676600 (9am-5pm EST) and we will assist in obtaining the
appropriate support channel. Outside the United States please
refer to http://www.dialogic.com/support/contact to obtain
local contact information.
Dialogic also provides direct support via Dialogic® Pro™
Services agreements. For more details of direct support from
Dialogic please refer to:
http://www.dialogic.com/support/DialogicPro.
Returning a Product
To return a board for warranty repair or any other returns,
please refer to the following:
http://www.dialogic.com/support/hwfaults.
To purchase Dialogic® products, please refer to the following
website to locate the appropriate supplier:
http://www.dialogic.com/purchase.htm.
All contents of this document are furnished for informational use only and are
subject to change without notice and do not represent a commitment on the part
of Dialogic Corporation or its subsidiaries (“Dialogic”). Reasonable effort is
made to ensure the accuracy of the information contained in the document.
However, Dialogic does not warrant the accuracy of this information and
cannot accept responsibility for errors, inaccuracies or omissions that may be
contained in this document.
INFORMATION IN THIS DOCUMENT IS PROVIDED IN CONNECTION
WITH DIALOGIC® PRODUCTS. NO LICENSE, EXPRESS OR IMPLIED,
BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY
RIGHTS IS GRANTED BY THIS DOCUMENT. EXCEPT AS PROVIDED
IN A SIGNED AGREEMENT BETWEEN YOU AND DIALOGIC,
DIALOGIC ASSUMES NO LIABILITY WHATSOEVER, AND DIALOGIC
DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY, RELATING TO
SALE AND/OR USE OF DIALOGIC PRODUCTS INCLUDING LIABILITY
OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR
PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY
INTELLECTUAL PROPERTY RIGHT OF A THIRD PARTY.
Dialogic products are not intended for use in medical, life saving, life
sustaining, critical control or safety systems, or in nuclear facility applications.
It is possible that the use or implementation of any one of the concepts,
applications, or ideas described in this document, in marketing collateral
produced by or on web pages maintained by Dialogic may infringe one or more
patents or other intellectual property rights owned by third parties. Dialogic
does not provide any intellectual property licenses with the sale of Dialogic
products other than a license to use such product in accordance with
intellectual property owned or validly licensed by Dialogic and no such
licenses are provided except pursuant to a signed agreement with Dialogic.
More detailed information about such intellectual property is available from
Dialogic’s legal department at 9800 Cavendish Blvd., 5th Floor, Montreal,
Quebec, Canada H4M 2V9. Dialogic encourages all users of its products to
procure all necessary intellectual property licenses required to implement
any concepts or applications and does not condone or encourage any
intellectual property infringement and disclaims any responsibility related
thereto. These intellectual property licenses may differ from country to
country and it is the responsibility of those who develop the concepts or
applications to be aware of and comply with different national license
requirements.
Dialogic, Diva, Eicon, Eicon Networks, Eiconcard and SIPcontrol, among
others, are either registered trademarks or trademarks of Dialogic. Dialogic's
trademarks may be used publicly only with permission from Dialogic. Such
permission may only be granted by Dialogic’s legal department at 9800
Cavendish Blvd., 5th Floor, Montreal, Quebec, Canada H4M 2V9. Any
authorized use of Dialogic's trademarks will be subject to full respect of the
trademark guidelines published by Dialogic from time to time and any use of
Dialogic’s trademarks requires proper acknowledgement. The names of actual
companies and products mentioned herein are the trademarks of their
respective owners.