datasheet for CD-12/103F 0Z5V8CTAF by Tecate Group

Tecate Group
Ceramic Capacitors
DISC CAPACITOR REFERENCE DATA
CLASS 1 SERIES (T.C. TYPE) NPO, N150, N1500, SL
CAPACITANCE
Test Frequency: 1MHz ± 100KHz for <1000pF.
1KHz ± 100Hz for >1000pF.
Test Voltage: Shall not exceed 1 ± 0.2Vrms.
Test Temperature: 25°C ± 2°C.
APPLICATIONS
• Resonant circuit.
• High Q requirement.
• High stability capacitor characteristics.
DISIPATION FACTOR
< 0.1 @ 25°C.
QUALITY FACTOR (Q)
For NPO to SL: When C < 30pF, Q = 400 + 20 x CpF; When C > 30pF, Q > 1000.
For C: above 1000pF @ 1KHz DF 0.2% maximum.
INSULATION RESISTANCE
10000MΩ minimum. Shall be measured after 1 minute at rated voltage.
DIELECTRIC WITHSTANDING VOLTAGE
Capacitors shall withstand, for not less than 1 second, a D.C. test.
Voltage of 3 times rated working voltage for ≤1KV.
CLASS 2 SERIES (HL-K TYPE) Y5F, Y5P, Z5U
CAPACITANCE
Test Frequency: 1KHz
Test Voltage: 1 ± 0.2Vrms.
Test Temperature: 25°C ± 2°C.
APPLICATIONS
• By-pass and coupling.
• Frequency discriminating where “Q” and stability of capacitor
characteristics are not of major importance.
DISSIPATION FACTOR
The DF shall not be greater than 2.5% for Y5E, Y5P & Z5U.
The DF shall not be greater than 5% for Y5V & Z5V.
INSULATION RESISTANCE
7500MΩ minimum. Shall be measured after 1 minute at rated voltage.
DIELECTRIC WITHSTANDING VOLTAGE
Capacitors shall withstand, for not less than 1 second, a D.C. test.
Voltage of 2.5 times rated working voltage.
CLASS 3 SERIES (S.C. TYPE) Y5R, Y5T, Y5V
Smaller sizes than Class-2, but lower ‘’Q’’.
CAPACITANCE
Test Frequency: 1KHz @ 25°C ± 2°C.
Test Voltage: Not greater than 0.1Vrms.
APPLICATIONS
• Transistorized.
• Low voltage electronic circuits for by-pass coupling.
DISSIPATION FACTOR
DF shall not exceed 5% for Y5P, Y5U, Y5V series.
INSULATION RESISTANCE
3.0VDC - 0.004MΩ - MFD.
10VDC ~ 12VDC - 0.04MΩ - MFD.
16VDC ~ 24VDC - 0.10MΩ - MFD. 25VDC ~ 50VDC - 100MΩ - MFD.
Dielectric withstanding voltage for less than 1 second at a test voltage of 2 times rated working voltage.
© Tecate Group Phone: (619) 398-9700 Fax: (619) 398-9777 Web Site: www.tecategroup.com
Specifications and dimensions are subject to change without notice.
Please confirm technical specifications with Tecate Group before purchasing.
Tecate Group
2012/02/21 Rev.04
Tecate Group
Ceramic Capacitors
DISC CAPACITOR REFERENCE DATA
CAPACITANCE TOLERANCE
Code
Tolerance Value
Apply T. C.
Remark
C
±0.25pF
NPO - N750
For smaller than 5pF.
D
±0.5pF
NPO - N750
For smaller than 5pF.
F
±1pF
NPO - N750
For smaller than 5pF.
J
±5%
NPO - N1000
For over 5pF.
K
±10%
NPO - N1000 (Y5E, Y5P)
For over 5pF.
M
±20%
Y5U, Z5U (Y5E, Y5P)
For over 100pF.
S
+50%, -20%
Y5U, Z5U, Z5V
Z
+80%, -20%
Y5U, Z5U, Z5V
P
+100%, -0%
Y5U, Z5U, Z5V
TEMPERATURE COEFFICIENT CHART
© Tecate Group Phone: (619) 398-9700 Fax: (619) 398-9777 Web Site: www.tecategroup.com
Specifications and dimensions are subject to change without notice.
Please confirm technical specifications with Tecate Group before purchasing.
Tecate Group
2012/02/21 Rev.04
Tecate Group
Ceramic Capacitors
PART NUMBERING SYSTEM
CD
- 1KO /
103 Z
0Z5V
1
E
TR
F
ROHS CCOMPLIANT
TR = Tape/Reel
TA = Tape/Ammo
– = Bulk
CERAMIC
DISC
MAX DIAMETER
(only if required)
Rated
Voltage
Nominal Capacitance
First two digits are
significant, third digit is
the number of zeros to
be added.
-012
-016
-025
-050
-100
-250
-500
-1K0
-2K0
-3K0
103 = 10,000pF = 0.01uF
1R0 = 1pF
3R3 = 3.3pF
100 = 10pF
220 = 22pF
101 = 100pF
221 = 220pF
102 = 1000pF
222 = 2200pF
103 = 0.01µF
223 = 0.022µF
104 = 0.1µF
224 = 0.22µF
Standard
Tolerance
Temperature Coefficient
OPERATING RANGE
Class II & III
F = ±1%
J = ±5%
K = ±10%
M = ±20%
Z = +80, -20%
P = +100, -0%
(G.M.V.)
B = ±0.1pF
C = ±0.25pF
D = ±0.5pF
First
Digit
LOW
temp
¬
Z+10°C
Y-30°C
X-55°C
Second Third
Digit
Digit
HIGH %Δ
temp
cap.
¬
¬
4+65°C F ± 7.5
5+85°C P ± 10
6+105°CR ± 15
7+125°CS ± 22
T+22
OPERATING RANGE
-33
U+22
Class I
-56
-30°C to +85°C
V+22
NPOØN1500
-82
SL (N330 ± 500ppm)
© Tecate Group Phone: (619) 398-9700 Fax: (619) 398-9777 Web Site: www.tecategroup.com
Specifications and dimensions are subject to change without notice.
Please confirm technical specifications with Tecate Group before purchasing.
Lead Spacing
mm
(in)
A
2.5
(0.1)
B
5.0
(0.2)
C
6.35
(0.25)
D
7.5
(0.3)
E
9.5
(0.37)
F
10
(0.4)
Tecate Group
2012/02/21 Rev.04
Tecate Group
Ceramic Capacitors
CERAMIC DISC TAPING SPECIFICATIONS
Item
Symbol
Specification
Body diameter
D
10.0
maximum
Body thickness
T
3.5
maximum
Lead-wire diameter
d
0.50
±0.05
Pitch of component
P
12.7
±1.0
Feed hole pitch
P0
12.7
±0.3
Feed hole center to lead
P1
3.85
±0.7
Hole center to component center
P2
6.35
±1.3
Lead-to-lead distance
F
5.0
±0.8
Component alignment, F-R
Dh
Tape width
W
18.0
±0.5
Hold-down tape width
W0
11.0
maximum
Hole position
W1
9.0
±0.5
Hold-down tape position
W2
3.0
maximum
Height of component from tape center
H
20.0
Component height
H1
32.25
maximum
2.0
maximum
Lead-wire protrusion
0
Cumulative pitch error: 1.0mm / 20 pitch.
±2.0 mm
±1
Feed hole diameter
Do
4.0
±0.3
Total tape thickness
t
0.7
±0.2
Length of snipped lead
L
11.0
maximum
Coating rundown on leads
C
2.0
maximum
© Tecate Group Phone: (619) 398-9700 Fax: (619) 398-9777 Web Site: www.tecategroup.com
Specifications and dimensions are subject to change without notice.
Please confirm technical specifications with Tecate Group before purchasing.
Remaks
Ground paper: 0.5mm + 0.1mm.
Tecate Group
2012/02/21 Rev.04