Installation Instructions PORTSMOUTH™ 4285.410

Installation
Instructions
PORTSMOUTH™
4285.410
4285.410F15
SINGLE CONTROL
PULL-DOWN BAR FAUCET
Thank you for selecting American-Standard...
the benchmark of fine quality for over 100 years.
To ensure that your installation proceeds smoothly-please read these instructions carefully before you begin.
Certified t o comply with ANSI A112.18.1M
M 9 6 5 4 5 5 R ev. 1. 2
RECOMMENDED TOOLS
Phillips Screwdriver
Regular Screwdriver
1
Adjustable Wrench
INSTALL FAUCET WITH OR WITHOUT DECK ESCUTCHEON
Plumbers' Putty or Caulking
CAUTION
Turn off water at
main supply.
(A) Installation with ESCUTCHEON (1). Apply a bead of putty to bottom edge of ESCUTCHEON with PUTTY PLATE (1).
Make certain the SEAL (9) is properly seated in recess of faucet body. Insert SUPPLY HOSES (2), SPRAY HOSE (7)
and SHANK (3) through hole of ESCUTCHEON with PUTTY PLATE (1) and mounting surface. Follow mounting instructions
below to secure faucet to mounting surface.
(B) Installation less ESCUTCHEON (1). Discard ESCUTCHEON with PUTTY PLATE (1). Make certain the SEAL (9)
is properly seated in recess of RING BASE (10). Insert supply HOSES (2), SPRAY HOSE (7) and SHANK (3) through
mounting hole and seat RING BASE (10) onto sink or mounting surface. Do not use putty.
Insert HOSES (2) through RUBBER WASHER (4), BRASS WASHER (5), and threaded LOCKNUT (6).
Assemble RUBBER WASHER (4), BRASS WASHER (5), and threaded LOCKNUT (6) onto SHANK (3) from underside
of sink or mounting surface. Hand tighten LOCKNUT (6).
Use a screwdriver to tighten SCREWS (8) on LOCKNUT (6). Work your way around LOCKNUT (6), tightening
the screws slightly each time until all are snug to ensure even pressure.
A
B
7
7
SPOUT BASE
9
2
3
7
4
PUTTY
SINK OR
MOUNTING
S U R FA C E
7
4
5
5
6
10
9
3
2
RING BASE
1
8
6
8
2
MAKE WATER SUPPLY CONNECTIONS
Turn off hot and cold water supplies before beginning.
Connect FLEXIBLE SUPPLIES (1, 2) directly
to wall supplies. Connection on fitting
supplies are 3/8" compression. Connect
left supply (Marked with a Red Stripe) to Hot
and right supply (Marked with Blue Stripe) to
Cold wall supply. Use adjustable wrench to
tighten connections. Do not over tighten.
2
1
Faucet supplies are 21" long from faucet base.
COLD
Note: If additional supply length is
required, installer must purchase
additional parts separately.
HOT
Important: If SUPPLY HOSES (1, 2) are
too long, loop as illustrated to avoid kinking.
3
CONNECT SPRAY HOSE & INSTALL WEIGHTS
Push the SPRAY HOSE END (1) into the HOSE CONNECTOR (2)
until it snaps into place.
With hand spray seated in spout, install WEIGHT (3)
onto HOSE (4) 24 inches from the underside of the sink deck
and secure with SCREW (5).
24"
(610mm)
2
1
5
3
4
4
TEST INSTALLED FAUCET
Move HANDLE (1) into "off"
position.
With HANDLE (1) in "off" position,
unthread SPRAY (3) from HOSE (2).
Turn on water supplies.
Operate handle back to front, in COLD
and HOT positions, to flush water lines
thoroughly.
Check connections for leaks.
(See Section 5)
Replace SPRAY (3) onto HOSE (2).
2
3
4a
REMOVE
1
SPRAY OPERATION
With FAUCET on pull down SPRAY (3). Check for
leaks. Make sure SPRAY (3) fully retracks and is
seated in the SPOUT HOLDER (4).
4
3
M 9 6 5 4 5 5 R ev. 1. 2
5
CHECK CONNECTIONS FOR LEAKS.
Move HANDLE into "off" position.
Turn on water supplies and check connections for leaks.
Operate HANDLE (2) up and down, left and right to flush
water lines thoroughly.
Operate HAND SPRAY and check connections for leaks.
CHECK CONNECTIONS
FOR LEAKS
6
SERVICE
If faucet drips, operate HANDLE several times from "off" to "on." Do not
apply excessive force.
Clogged CARTRIDGE outlets or inlets may cause reduced flow.
To clean, first turn off water supply then:
Remove INDEX BUTTON (1), loosen HANDLE SCREW (2) and remove HANDLE (3).
Unthread the ESCUTCHEON CAP (4). Unthread three MOUNTING SCREWS (5).
Lift CARTRIDGE (6) off MANIFOLD (7).
Clean MANIFOLD (7) and CARTRIDGE (6) ports.
Place CARTRIDGE (6) onto MANIFOLD (7) and tighten MOUNTING SCREWS (5) alternately.
Replace ESCUTCHEON CAP (4), HANDLE (3), tighten HANDLE SCREW (1) and install INDEX BUTTON (2).
3
6
1
2
7
5
7
4
CARE:
DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.
DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A
CLOTH WITH A COARSE SURFACE.
M 9 6 5 4 5 5 R ev. 1. 2
PORTSMOUTH™
SINGLE CONTROL
PULL-DOWN BAR FAUCET
MODEL NUMBER
4285.410
4285.410F15
M920017-0020A
SPRAY HOSE
M951483-0070A
CARTRIDGE
M964178-YYY220A
(2.2 GPM)
SPRAY ASSEMBLY
M964397-0070A
BUTTON AND
SCREW KIT
M907315-YYY0A
ESCUTCHEON CAP
M964178-YYY150A
(1.5 GPM)
SPRAY ASSEMBLY
M918511-0070A
CARTRIDGE SCREWS
M907989-YYYOA
MOUNTING RING KIT
M964396-YYY0A
HANDLE KIT
A911836-0070A
SEAL
M964065-YYY0A
ESCUTCHEON AND
PUTTY PLATE
M962146-0070A
MOUNTING KIT
Replace the YYY with
Appropriate finish code
CHROME
STAINLESS STEEL
OIL RUBBED BRONZE
002
075
224
M964395-0070A
WEIGHT
HOT LINE FOR HELP
M 9 6 5 4 5 5 R ev. 1. 2
For toll-free information and answers to your questions, call:
1-800-442-1902
Weekdays 8:00 a.m. to 6:00 p.m. EST
IN CANADA 1-800-387-0369 (TORONTO 1-905-306-1093)
Weekdays 8:00 a.m. to 7:00 p.m. EST
IN MEXICO 01-800-839-1200
Product names listed herein are trademarks of American Standard Inc.
© AS America, Inc. 2012