Carpet Maintainer
Operating instructions (ENG)
MODELS:
IM
10066360
IMIE17
10066550
IMX
10066400
IMXIE17
10066410
IMIE17 AU
10060990
IMXIE17 AU
10061030
IMIE17 UK
10060980
IMXIE17 UK
10061020
Read these instructions before using the machine.
86269870 - R
06/04/09
Machine Data Log / Overview
OVERVIEW
The Carpet Maintainer is designed to maintain carpet using the Quick Dry Carpet Care System. The machine has
two counter rotating brushes that scrub chemical into the carpet. The chemicals, iCapsol or Prochem ProCaps,
encapsulates the dirt, allowing both to be vacuumed up once the chemical has dried. The brushes also raise the
pile of the carpet. The Deluxe models have a solution tank and pump powered spraying system, which applies the
chemical to the carpet as the machine is used.
2
86269870 CARPET MAINTAINER
Table of Contents
Machine Data Log / Overview. . . . . . . . . . . . . . . . . . 2
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
How to Use This Manual . . . . . . . . . . . . . . . . . . . . . . 4
IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . 5
Hazard Intensity Level . . . . . . . . . . . . . . . . . . . . . . . 6
Grounding Instructions - . . . . . . . . . . . . . . . . . . . . . . 7
Safety Label Locations . . . . . . . . . . . . . . . . . . . . . . . 8
Operations
Technical Specifications . . . . . . . . . . . . . . . . . . . . . . 9
How The Machines Work . . . . . . . . . . . . . . . . . . . . 10
Quick Dry Carpet Care System Instructions . . . . . . 10
Machine Operation . . . . . . . . . . . . . . . . . . . . . . . . . 11
Transporting A Sprayer. . . . . . . . . . . . . . . . . . . . . . 12
Shut-Down And Storage . . . . . . . . . . . . . . . . . . . . . 12
Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
PARTS
Brush. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brush Lift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Decal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical 120V . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical 230V . . . . . . . . . . . . . . . . . . . . . . . . . . .
Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Frame Deluxe . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Handle. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hopper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Solution Tank - Deluxe . . . . . . . . . . . . . . . . . . . . .
Wiring 120V . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wiring 230V . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wiring 120V - Deluxe . . . . . . . . . . . . . . . . . . . . . .
Wiring 230V - Deluxe . . . . . . . . . . . . . . . . . . . . . .
Suggested Spare Parts . . . . . . . . . . . . . . . . . . . . .
Serial Numbers . . . . . . . . . . . . . . . . . . . . . . . . . .
20
22
24
26
28
30
32
34
36
38
40
42
44
46
48
50
52
53
Maintenance
Brush Cleaning And Maintenance . . . . . . . . . . . . . 14
Motor Replacement & Belt Tensioning . . . . . . . . . . 14
Machine Maintenance. . . . . . . . . . . . . . . . . . . . . . . 16
Machine Troubleshooting . . . . . . . . . . . . . . . . . . . . 17
86269870 CARPET MAINTAINER
3
How to Use This Manual
This manual contains the following sections:
•
•
•
•
•
HOW TO USE THIS MANUAL
SAFETY
OPERATIONS
MAINTENANCE
PARTS LIST
The PARTS LIST section contains assembled parts
illustrations and corresponding parts list. The parts lists
include a number of columns of information:
•
The HOW TO USE THIS MANUAL section will tell you
how to find important information for ordering correct
repair parts.
Parts may be ordered from authorized dealers. When
placing an order for parts, the machine model and
machine serial number are important. Refer to the
MACHINE DATA box which is filled out during the
installation of your machine. The MACHINE DATA box
is located on the inside of the front cover of this manual.
The model and serial number of your machine is on the
operator's left hand side, side panel of base.
The SAFETY section contains important information
regarding hazard or unsafe practices of the machine.
Levels of hazards is identified that could result in
product or personal injury, or severe injury resulting in
death.
REF – column refers to the reference number
on the parts illustration.
• PART NO. – column lists the part number for
the part.
• PRV NO. – reference number.
• QTY – column lists the quantity of the part used
in that area of the machine.
• DESCRIPTION – column is a brief description
of the part.
• SERIAL NO. FROM – If this column has an (*)
and a Reference number, see the SERIAL
NUMBERS page in the back of your manual. If
column has two asterisk (**), call manufacturer
for serial number. The serial number indicates
the first machine the part number is applicable
to. The main illustration shows the most current
design of the machine. When a boxed illustration is shown, it displays the older design.
• NOTES – column for information not noted by
the other columns.
NOTE: If a service or option kit is installed on your
machine, be sure to keep the KIT INSTRUCTIONS
which came with the kit. It contains replacement parts
numbers needed for ordering future parts.
NOTE: The manual part number is located on the
lower left corner of the front cover.
The OPERATIONS section is to familiarize the operator
with the operation and function of the machine.
The MAINTENANCE section contains preventive maintenance to keep the machine and its components in
good working condition.
4
86269870 CARPET MAINTAINER
Safety
IMPORTANT SAFETY INSTRUCTIONS
When using an electrical appliance, basic precaution
must always be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.
To reduce the risk of fire, electric shock, or injury:
Connect to a properly grounded outlet. See Grounding Instructions.
Do not leave the machine unattended. Unplug machine from outlet when not in use and before maintenance or
service.
Do not allow machine to be used as a toy. Close attention is necessary when used by or near children.
Use only as described in this manual. Use only manufacturer's recommended components and attachments.
Do not use damaged electrical cord or plug. Follow all instructions in this manual concerning grounding the
machine. If the machine is not working properly, has been dropped, damaged, left outdoors, or dropped into
water, return it to an authorized service center.
Do not pull or carry machine by electrical cord, use as a handle, close a door on cord, or pull cord around sharp
edges or corners.
Do not run machine over cord or allow the rotating brushes to come in contact with the cord. Keep cord away from
heated surfaces.
Do not unplug machine by pulling on cord. To unplug, grasp the electrical plug, not the electrical cord.
Do not handle the electrical plug or machine with wet hands.
Do not operate the machine with any openings blocked. Keep openings free of debris that may reduce airflow.
Machine is designed for indoor use only and must not be operated or stored outdoors in wet conditions.
Turn off all controls before unplugging.
This machine is suitable for commercial use, including hotels, schools, hospitals, factories, shops and
offices for more than normal housekeeping purposes.
Maintenance and repairs must be done by qualified personnel.
Machine can cause a fire when operating near flammable vapors or materials. Do not operate this machine near
flammable fluids, dust or vapors.
SAVE THESE INSTRUCTIONS
86269870 CARPET MAINTAINER
5
Safety
Hazard Intensity Level
The following symbols are used throughout this guide as indicated in their descriptions:
There are three levels of hazard intensity identified by signal words -WARNING and CAUTION and FOR SAFETY.
The level of hazard intensity is determined by the following definitions:
WARNING - Hazards or unsafe practices which could result in severe personal injury or death.
CAUTION - Hazards or unsafe practices which could result in minor personal injury or product or property damage.
FOR SAFETY: To Identify actions which must be followed for safe operation of equipment.
Report machine damage or faulty operation immediately. Do not use the machine if it is not in proper operating
condition. Following is information that signals some potentially dangerous conditions to the operator or the equipment. Read this information carefully. Know when these conditions can exist. Locate all safety devices on the
machine. Please take the necessary steps to train the machine operating personnel.
FOR SAFETY:
DO NOT OPERATE MACHINE:
Unless Trained and Authorized.
Unless Operation Guide is Read and understood.
In Flammable or Explosive areas.
In areas with possible falling objects.
WHEN SERVICING MACHINE:
Avoid moving parts. Do not wear loose clothing; jackets, shirts, or sleeves when working on the machine.
Use approved replacement parts.
6
86269870 CARPET MAINTAINER
Safety
This Product Is For Commercial Use Only.
Electrical
In the USA, this machine operates on a standard 15
amp 120V, 60 hz, A.C. power circuit. The amp, hertz,
and voltage are listed on the data label found on each
machine. Using voltages above or below those
indicated on the data label will cause serious damage
to the motors.
Extension Cords
If an extension cord is used, the wire size must be at
least one size larger than the power cord on the
machine, and must be limited to 50 feet (15.5m) in
length.
Grounding Instructions 120V Only
This appliance must be grounded. If it should malfunction or break down, grounding provides a path of least
resistance for electric current to reduce the risk of
electric shock. This appliance is equipped with a cord
having an equipment-grounding conductor and
grounding plug. The plug must be inserted into an
appropriate outlet that is properly installed and
grounded in accordance with all local codes and ordinances.
Improper connection of the equipment-grounding
conductor can result in a risk of electric shock. Check
with a qualified electrician or service person if you are
in doubt as to whether the outlet is properly grounded.
Do not modify the plug provided with the appliance - if it
will not fit the outlet, have a proper outlet installed by a
qualified electrician.
This appliance is for use on a nominal 120-volt circuit,
and has a grounded plug that looks like the plug in "Fig.
A". A temporary adaptor that looks like the adaptor in
"Fig. C" may be used to connect this plug to a 2-pole
receptacle as shown in "Fig. B", if a properly grounded
outlet is not available. The temporary adaptor should
be used only until a properly grounded outlet (Fig. A)
can be installed by a qualified electrician. The green
colored rigid ear, lug, or the like extending from the
adaptor must be connected to a permanent ground
such as a properly grounded outlet box cover.
Whenever the adaptor is used, it must be held in place
by a metal screw.
86269870 CARPET MAINTAINER
7
Safety
Safety Label Locations
The following WARNING LABEL(S) are found on your cleaning unit. These labels point out important Warnings and
Cautions which should be followed at all times. Failure to follow warnings and cautions could result in fatality,
personal injury to yourself and/or others, or property damage. Follow these instructions carefully! DO NOT remove
these labels.
NOTE: If at any time the labels become illegible, promptly replace them.
WARNING LABEL
PART NUMBER 86220140
PRV 500895
8
86269870 CARPET MAINTAINER
Operations
Technical Specifications
120V
ITEM
Electrical
Nominal Power
Rated Amperage
Brush Width
Brush RPM
Wheels
Dimensions - Weight
- Weight
- Deluxe
Dimensions - Height with handle
Dimensions - Depth
Power Cord
Solution Tank Volume - Deluxe
Pump Pressure - Deluxe
Solution Flow - Deluxe
Spray Jet Size - Deluxe
DIMENSION/CAPACITY
120V
0.5 HP
7 Amps
17 - 16.5" (430 - 420 mm)
470 RPM
3 inches (75 mm) non-marking grey
48 lbs. (22 kg)56 lbs. (25 kg)
45.5" (1.16 m)
16 inches (0.4 m)
40 feet (12.2 m)
2 gallon
50 psi
0.1 gpm
.010
230 V
ITEM
Electrical
Nominal Power
Rated Amperage
Brush Width
Brush RPM
Wheels
Dimensions - Weight
- Weight
- Deluxe
Dimensions - Height - with handle
Dimensions - Depth
Power Cord
Solution Tank Volume - Deluxe
Pump Pressure - Deluxe
Solution Flow - Deluxe
Spray Jet Size - Deluxe
DIMENSION/CAPACITY
230V
0.5 HP
4 Amps
17 - 16.5" (430 - 420 mm)
470 RPM
3 inches (75 mm) non-marking grey
48 lbs. (22 kg)56 lbs. (25 kg)
45.5" (1.16 m)
16 inches (0.4 m)
40 feet (12.2 m)
2 gallon
50 psi
0.1 gpm
.010
Special Notes:
The sound pressure level at the operator's ear was
measured to be 67.7dBA . This was a nearfield, broadband measurement taken on a carpeted floor. This
appliance contains no possible source of impact noise.
The instantaneous sound pressure level is below 63 Pa.
The weighted root mean square acceleration at the
operator's arms was measured to be below 2.5m/s2 .
This was a tri-axial, third-octave-band measurement
made during normal operation on a composite tile floor.
The measurement and related calculations were made
in accordance with ISO 5349-1.
NOTE: This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure
that they do not play with the appliance.
86269870 CARPET MAINTAINER
9
Operations
How The Machines Work
The Carpet Maintainer is designed to maintain your
carpet using the Quick Dry Carpet Care System. By
using the Carpet Maintainer in conjunction with iCapsol
or Prochem ProCaps chemical solution, you can
perform a regular light cleaning and grooming of your
carpet very quickly, and have the carpet dry and ready
for traffic within 20 minutes.
The handle movement flexibility allows the machine to
clean under low furniture. There is a hand operated on/
off switch and auto-handle lock keeping the handle in
an upright position. This unit is equipped with a safety
feature that when unplugged from the wall or the
handle dropped, will automatically reset to the off
position .
The debris tray is used to catch unwanted carpet debris
and should be cleaned regularly and prior to transporting.
This appliance conforms with international and national
safety directives: EN55014-2, EN5504-1, EN61000-32/3-3, EN60335-1/2-10/2-69/2-67. IEC 60335-1/2/10/267/2-69. LVD 73/23/EEC.
Deluxe
This unit is equipped with an onboard spray pump and
solution tank. By using the onboard spraying system a
light treatment of chemical can be applied to the carpet
and brushed in during a single pass of the machine.
Quick Dry Carpet Care System
Instructions
4. No dwell time is required. Do not allow chemical to
dry before brushing.
5. Brush treated area to emulsify soils using the
Windsor iCapsol or other carpet-brushing machine.
6. Allow to dry until dry to touch (approximately 20
minutes) before opening area to traffic.
7. Vacuum carpet when fully dry to remove encapsulated soil.
Tips: Pre-treat carpet spots with iCapsol Interim
cleaning solution. Work on a manageable area and do
not allow cleaning solution to dry on carpet before
brushing.
Deluxe
The Deluxe is provided with a removable solution tank.
To remove tank for filling and cleaning, press the gray
release button on the blue coupler located at the top of
the tank. Next remove upper straps from mounting
pegs. The tank will now freely separate from the
machine base. After filling tank remount to machine by
reversing the process mentioned above.
The proper 1:16 dilution ratio can be achieved by
adding one pint (16 oz.) of recommended chemical and
slowly filling the tank with water (2 gallons). Adding
water slowly will help prevent foaming.
To achieve a coverage rate of 600-1000 sq. ft. per
gallon using the onboard sprayer, spray solution only
during the forward stroke of operation. Use the backstroke to brush the chemical into the carpet.
Test for colorfastness in an inconspicuous area before
use.
1. Vacuum carpet to remove loose soil.
2. Dilute iCapsol or Prochem ProCaps at 8oz. per
gallon of water (1:16) into the solution tank.
3. Pre-spray carpet to be cleaned at a rate of 6001000 sq. ft. per gallon of diluted solution. Do not
over wet.
10
86269870 CARPET MAINTAINER
Operations
Machine Operation
Starting Machine - Deluxe
NOTE: Perform pre-run machine check before
operating machine.
Pre-Run Inspection
Perform a pre-run inspection to find possible problems
that could cause poor performance or lost time from
breakdown. Check the rating plate to confirm voltage
and frequency is the same as the power supply. NOTE:
A 10% variation in voltage is acceptable.
FOR SAFETY: Before starting machine, make sure
that all covers are in place and secured properly.
Starting Machine
3. (a) Press green button to power on machine, 120V
only.
NOTE: Perform pre-run machine check before
operating machine.
FOR SAFETY: Before starting machine, make sure
that all covers are in place and secured properly.
1. Connect the machine to a power supply.
2. Release the handle lock.
3. (a) Press green button to power on the
machine,120V only.
(b) Set black on/off switch to "on" position, 230V
only.
4. Press green button to start brushes.
1. Connect the machine to a power supply.
2. Release the handle lock.
(b) Set black on/off switch to "on" position, 230V
only.
4. Press green button to start brushes.
5. Press and hold blue button to spray chemical.
Once machine is plugged in spray function is operational.
Apply a light spray of diluted interim carpet cleaner onto
the carpet using the onboard spraying system. Spray
chemical while pushing the machine forward. Brush
the chemical into the carpet while pulling the machine
slowly over the wetted carpet. Move the machine in
multiple directions and overlapping strokes.
After applying a light spray of diluted interim carpet
cleaner onto the carpet using a pressurized tank
sprayer, commence cleaning by pushing and pulling
the machine slowly over the wetted carpet.
For best results use Windsor iCapsol or Prochem
ProCaps products.
Move the machine in multiple directions and overlapping strokes.
Flammable materials can cause an explosion or fire.
Do not use flammable materials with this machine.
For best results use Windsor iCapsol or Prochem
ProCaps products.
86269870 CARPET MAINTAINER
11
Operations
Transporting A Sprayer
Shut-Down And Storage
This machine has the capability to mount a small pumpup sprayer.
1. Flush the spray jet and tank with hot water (Deluxe
only)
Transporting Chemical - Deluxe
2. After flushing, uncouple quick disconnect to
prevent water from dripping out of front jet.
This machine has the capability to mount
chemical bottles or trigger sprayers to the back of the
solution tank.
3. (a) Press red button to power off machine
120V only.
(b) Set black on/off switch to "off" position
230V only.
This Machine is not intended to carry more than 30
pounds. Carrying more than 30 pounds could cause
damage to the machine.
4. Lock handle in the upright position.
5. Disconnect the power cord from the power supply.
Wind the power cord around the cable holders on
the handle.
6. Remove the brushes for cleaning. See Brush
Cleaning and Maintenance section.
7. Clean debris tray.
The machine is now ready for storage until the next
use. Make sure to store your equipment in a dry place
to prolong the life of your machine. Storage outdoors or
unprotected could cause damage to your machine or
internal parts, therefore voiding your warranty.
12
86269870 CARPET MAINTAINER
Operations
Components
8
2
1A
1B
1A
1B
2
5
4
4
6
3
3
iCapsol Mini
1. A. Stop Switch (red-120V only)
B. On/Off Switch (black-230 only)
7
iCapsol Mini Deluxe
5. Tank
6. Strainer
2. Start Switch (green)
7. Jet
3. Brushes
8. Spray Pump Switch
4. Handle Release
86269870 CARPET MAINTAINER
13
Maintenance
Brush Cleaning And Maintenance
6. Mark left and right on the lift cams.
After each session of carpet cleaning, the brushes and
the brush housing should be cleaned. Before cleaning
or changing the brushes, always unplug the machine
from the power supply.
7. Remove the two cam bolts. This will also free the
lift cams.
NOTE: There are four plastic bushings that the
handle pivots on, leave them on the motor clamps.
Brushes are removed without tools. After handle is in
locked position, tilt the machine back and rest on
handle. To release brush from spring clip pull spring clip
away from brush end cap. Lift brush out of machine.
LIFTING CAM
LEFT
The brushes may be soaked in warm or hot water using
mild detergent, and then rinsed with warm water.
NOTE: Brushes with crushed bristles can often be
restored to original condition by soaking in hot water.
LIFTING CAM
RIGHT
Keep brushes clean and free from debris. Rotate
brushes after every use as this will increase the life
span of the brushes and ensure even wear.
Before reinstalling brushes, clean out machine brush
housing and hopper by wiping with a clean damp cloth.
Motor Replacement & Belt Tensioning
8. Remove the handle assembly.
1. Disconnect machine power supply.
9. Unscrew the wiring grommet from the main cover,
and set retaining bracket and screw aside.
2. Detach quick disconnect hose from top of solution
tank. (Deluxe Only)
10. Remove the the front and back screws and move
the main cover to the side.
3. Remove elastic straps and solution tank. (Deluxe
Only)
NOTE: The handle assembly and cover are still
attached to the frame by wiring. Be careful not to
pinch wiring when reassembling.
4. Remove two dome screws and dome assembly.
11. Remove the (2) plastic finger guards.
12. Remove the motor clamps and lift brackets.
DOME
MOTOR CLAMP
CIRCUIT BREAKER
& BOOT
LIFT BRACKET
COVER
MOTOR
WIRING GROMMET
5. Remove the circuit breaker boot and push the
circuit breaker clear of cover.
14
PLASTIC FINGER
GUARD (2)
86269870 CARPET MAINTAINER
Maintenance
13. Unplug motor wires. Loosen end cap screws, 1 full
turn.
HANDLE MOUNT
ASSEMBLY
END CAP
SCREWS
ROTATE MOTOR
RIGHT HAND
GEAR DRIVE
ACCESS HOLE
FOR LOWER
SCREW
LIFT BRACKETS
MOTOR CLAMPS
BELT
PULLEY
ROTATE MOTOR
LEFT HAND
GEAR DRIVE
MOTOR
19. Turn the motor body inside motor clamps so that
the left hand gear drive pivots upwards. Take all of
the slack out of the left hand gear drive belt and
snug left hand motor clamp bolts.
BELT
PULLEY
20. While holding the motor stationary, turn the right
hand gear drive downward so that the gear drive
housing touches the setscrew in the frame. This
set screw was installed on the assembly line and
establishes the correct position for the motor.
14. Remove belts.
21. Tighten the screw in the long gear drive cap.
15. Lift motor out of housing, and remove pulleys. Set
pulleys aside for re-installation.
22. Tighten all four motor clamp bolts.
16. Take the new motor and loosen the screws in the
long rear drive end cap. This allows the end cap to
swivel +/- 20 degrees. Do not remove the end cap
screws, only back them off 1 full turn.
17. Put the motor in the cradle on the frame. Place
pulleys onto motor shaft's. Loop the drive belts
onto motor drive pulleys.
18. Place lift brackets on motor, align over pins. Put
the motor/clamp mount assembly over the motor
and lightly snug the retaining bolts. The motor
must be able to turn inside the motor clamps. If
clamps are too tight to move the motor by hand,
loosen clamp bolts.
23. Check both belts for equal tension. The belts
should not sag under their own weight, however,
should flex easily when squeezed with fingers. If
the tension is clearly unequal, loosen the motor
mount bolts and retighten. This will equalize the
belt tension from on side to the other.
24. Reinstall finger guards
25. Reinstall lift brackets with top surface lip on inside.
26. Reinsert circuit breaker through hole in cover,
reattach cover, circuit breaker boot, and wiring
grommet.
27. Verifying lifter cams are on correct side, reattach
handle assembly.
28. Reattach dome cover.
29. Reattach solution tank and reconnect top hose.
(Deluxe Only)
86269870 CARPET MAINTAINER
15
Maintenance
Machine Maintenance
Periodic Maintenance
The Maintainer requires very little maintenance. Wipe
down the machine periodically with a clean cloth. DO
NOT spray water directly over the top of machine.
1. Check all handles, switches, electrical cables and
connections on your machine for damage. Repair
or replace immediately.
2. Inspect and/or replace brushes.
Deformation of the brush bristles can result in unbalanced running and excessive vibrating or jumping.
The machine is fitted with a circuit breaker. In the
unlikely event of overloading, the circuit breaker will
automatically trip. It can be reset after approximately 30
seconds (or when the machine cools down) by pushing
the set button located on the cover housing.
Replace brushes when main bristles are worn to
the same level as the yellow indicator bristles.
3. Check spray pattern. Clean or replace jet if the
pattern is blocked or uneven
Annual Maintenance
1. Check all bearings for noise and wear.
2. Check motor for operation.
Daily Maintenance
3. Check overall machine for operation.
1. Clean and inspect brushes.
2. Clean and inspect brush housing, debris tray and
machine. Rinse debris tray if needed.
4. Check belts for wear and change belts every
second year.
3. Inspect power cord for wear or damage. This cable
will lie on wet carpet. To prevent electrical shock
replace cords that are frayed or have cracked insulation immediately.
4. Flush the tank, pump and spray jet with hot water
(Deluxe only).
5. Clean Strainer.
16
86269870 CARPET MAINTAINER
Maintenance
Machine Troubleshooting
PROBLEM
CAUSE
SOLUTION
Tripped electrical circuit breaker
Check building circuit breaker
in fuse box of building
Faulty power cord
Replace power cord
Power switch failure or relay
Replace power switch or relay
failure
No power to machine
Reset circuit breaker. Higher amp draw may
Tripped circuit breaker
indicate faulty parts. Find parts not moving freely
and correct as needed.
With machine unplugged, check for and correct,
Internal wiring problem
any loose wire connections.
Faulty rectifier
Replace rectifier
Equipment not grounding
Follow grounding instructions, pg 2-3
Receptacle not grounded
Have an electrician inspect the building's wiring
Electrical Shock
Check for any loose wire connections, replace
Interal electrical problem
any items that are short circuiting
Faulty circuit breaker
Replace circuit breaker
Nuisance tripping of circuit
Test circuit breaker for continuity. Higher amp
breaker
Mechanical problem
draw may indicate faulty parts. Find parts not
moving freely and repair or replace.
Faulty brush motor/gear box
Replace brush motor/gear box
Brush not turning or scrubbing Belt failure
Replace belts
Worn brush motor brushes
Replace brushes, check commutator
Power to motor but motor does
Worn brush motor brushes
Replace brushes, check commutator
not run
Bearing squealing or grinding
Worn bearings
Replace worn bearing
in brush housing
Machine will only run if the
Defective red (off) switch.Sends
Replace or reconnect wire to red (off) switch
green (on) switch is continuconstant "off" signal.
ously held down
No flow or uneven flow from jet
Clogged jet
Clean or replace jet
(Deluxe only)
Weak flow from clean jet
Clogged strainer
Clean strainer
(Deluxe only)
Pump runs but no flow from jet Disconnect coupling at solution
Attach the quick coupling to the solution tank
(Deluxe only)
tank
86269870 CARPET MAINTAINER
17
Notes
18
86269870 CARPET MAINTAINER
PARTS
86269870 CARPET MAINTAINER
19
Brush
3
6
5
4
3
7
2
1
8
20
86269870 CARPET MAINTAINER
Brush
REF
PART NO.
PRV NO.
QTY
1
2
3
4
5
6
7
8
86217340
86172630
86172870
86224670
86214850
86217330
86216070
86172840
270130
57314
70898
730396
12544
270129
12535
70886
1
2
6
2
2
1
2
6
DESCRIPTION
SERIAL NO.
FROM
NOTES
COVER, BELT, RIGHT
NUT, M4, LK, SST
SCR, M4X14, PHMS, DIN7985 SST
SPRING, BRUSH CLIP
ASSY, BRUSH & HUB
COVER, BELT, LEFT
ASSY, BRUSH DRIVE
SCR, M5X10, PHS, FHD, SST
86269870 CARPET MAINTAINER
21
Brush Lift
1
2
3
4
5
6
22
86269870 CARPET MAINTAINER
Brush Lift
REF
PART NO.
PRV NO.
QTY
1
2
3
4
5
6
86215580
86172700
86215750
86224760
86215740
86223620
141042
67606
09156
73997
09155
67605
2
4
4
4
4
2
DESCRIPTION
SERIAL NO.
FROM
NOTES
BRACKET, CROSSOVER PUSH
RING, E-TYPE, 5MM ID, DIN6799
BRG, FLNG, 6MM IDX7MM LONG
SPRING, COM, 18.28 OD X 25L
BRG, FLNG, 6MM IDX24MM LONG
ROD, LIFTING
86269870 CARPET MAINTAINER
23
Decal
1
2A
2B
24
86269870 CARPET MAINTAINER
Decal
REF PART NO. PRV NO. QTY
1
2A
2B
86221620
86244630
86244920
501260
501190
501247
1
1
1
DESCRIPTION
LABEL, CHEMICAL INSTR.
LABEL, MAIN, ICAPSOL MINI
LABEL, PROCAP PROCHEM
86269870 CARPET MAINTAINER
SERIAL NO.
FROM
NOTES
DELUXE ONLY
WINDSOR ONLY
PROCHEM ONLY
25
Electrical 120V
DELUXE ONLY
27
28
26
31
29
27
6 7
30
8
2
13 12
16
1
8
7
19
17
18
15
23 23
15
22
6
20
20
14
26
10
DELUXE ONLY
11
9
5
25
3
8
5
4
26
21
86269870 CARPET MAINTAINER
Electrical 120V
REF PART NO. PRV NO. QTY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
86002010
86217120
86214770
86214780
86225070
86198450
86225320
86173100
86291470
86291490
86291880
86216800
86277600
86215670
86172880
86173200
86225850
86223400
86223390
86173210
86291860
86222670
86216740
OPEN
86013570
86299320
86313930
86295190
86295150
86295180
86314630
14942
23729
38370
38371
38372
20005
78601
70935
20110
70882
140839
70901
70950
87517
67516
67488
70951
05248
20040
-
1
1
1
1
2
2
1
4
1
1
2
1
1
1
5
1
2
1
1
4
1
1
2
2
2
1
2
1
1
1
DESCRIPTION
SERIAL NO.
FROM
BOOT, 3/8 CIRCUIT BREAKER
CORD SET, 18/3 X 40FT SJT
ASM RED BUTTON W/BEZEL
ASM GREEN BUTTON W/BEZEL
SWITCH, ITW, MICRO
CLAMP, 5/16 NYLON
TIE, CABLE NYLON
SCR, M3X6, BSHCS, SST
BRKT, MTR BRKT, SWITCH, CVR
COVER, SWITCH, BRKT
SCR, M3X12, BSHCS, SST
CLIP, WIRE
SCR, M4X20, PPHMS, SST
BREAKER, 8A VDE CIRCUIT
SCR, M4X6, BSHCS, SST
SCR, M4X16, BSHCS, SST
WASHER, M3, FL, ISO7089, SST
RELAY, 15A 120VAC MINI
RECTIFIER, 50A 600V BRIDGE
SCR, M5X10, BSHCS, SST
SWITCH, 125VAC SP NC ROLLER
PLATE, BASE, ELECTRICAL MTG
CLAMP, 17,7 NYLON
SWITCH, PUSHBUTTON, BL, DLX
LABEL, GROUND SYMBOL
SWITCH, W/COUPLER, N.C.
ASM, BUTTON, BLUE, W/BEZEL
ASM, BUTTON, RED, W/BEZEL
ASM, BUTTON, GREEN, W/BEZEL
SWITCH, W/COUPLER, N.O.
NOTES
DELUXE ONLY
*(1)
*(1)
*(1)
*(1)
*(1)
DELUXE (QTY 3)
DELUXE ONLY
*See Serial Number Page
**Call Manufacturer For Serial Number.
86269870 CARPET MAINTAINER
27
Electrical 230V
DELUXE ONLY
3
30
19 31
28
4
3
1
2
5
6A
6B
14 13
7
23
29
12
24
25
22
15
4
8
8
4
16
18
5
17
31
27
20
21
33
32
26
28
86269870 CARPET MAINTAINER
Electrical 230V
REF
PART NO.
PRV NO.
QTY
DESCRIPTION
1
2
3
4
5
6A
6B
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
86299810
86295180
86313930
86172880
86198450
86217200
86310620
86002010
86216740
86215910
86225080
86173110
86173100
86216800
86277600
86302450
86215710
86173210
86222670
86225320
86291490
86291880
86223420
86173200
86223460
86225850
86291860
86299320
86299830
86264940
86295190
86299320
86173100
86291470
70901
20005
23738
14942
20040
140972
72152
70936
70935
20110
70882
141046
70951
05248
78601
67622
70950
67499
87517
27051
70935
-
1
1
1
5
2
1
1
1
2
1
1
2
3
1
1
1
1
4
1
4
1
2
1
1
1
2
1
1
1
1
2
2
2
1
SWITCH, BLACK, ROCKER, DPST
ASM, BUTTON, GREEN, W/BEZEL
SWITCH, W/COUPLER, N.C.
SCR, M4X6, BSHCS, SST
CLAMP, 5/16 NYLON
CORD SET, EURO 1MM X 40 BLACK
CORD SET, 18/3 X 40FT AUS
BOOT, 3/8 CIRCUIT BREAKER
CLAMP, 17,7 NYLON
BRKT, MTR BRKT, SWITCH
SWITCH, 125VAC SP NC ROLLER
SCR, M3X16, BSHCS, SST
SCR, M3X6, BSHCS, SST
CLIP, WIRE
SCR, M4X20, PPHMS, SST
ASM, FILTER, EMI MAIN
BREAKER, 5A VDE CIRCUIT
SCR, M5X10, BSHCS, SST
PLATE, BASE, ELECTRICAL MTG
TIE, CABLE NYLON
COVER, SWITCH, BRKT
SCR, M3X12, BSHCS, ISO7380, SS
RELAY, 10A 230V MINI SPDT
SCR, M416, BSHCS, SST
RECTIFIER, 50A 1000V BRIDGE
WASHER, M3, FL, ISO7089, SST
SWITCH, 125VAC SP NC NO-ROLLER
LABEL, GROUND SYMBOL
COVER, SWITCH, PVC
CABLE TIE, 11.38" UL/CSA
ASM, BUTTON, BLUE, W/BEZEL
LABEL, GROUND SYMBOL
SCR, M3X6, BSHCS, ISO7380, SST
BRKT, MTR BRKT, SWITCH
SERIAL NO.
FROM
NOTES
*(1)
DELUXE (QTY 3)
WAS 86223390
DELUXE ONLY
*See Serial Number Page
**Call Manufacturer For Serial Number
86269870 CARPET MAINTAINER
29
Frame
7
6
5
4
3
2
1
30
86269870 CARPET MAINTAINER
Frame
REF
PART NO.
PRV NO.
QTY
DESCRIPTION
1
2
3
4
5
6
7
86225340
86217930
86214820
86277600
86222360
86214830
86173050
78952
34450
05262
70882
58009
05263
70920
1
1
1
1
1
1
3
TRAY, IRENEW MINI
FRAME, 3.5", SINGLE MOTOR
ASSY, COVER, INSULATION
SCR, M4X20, PPHMS, SST
NUT, M4X0.7, U-CLAMP, 3MM PANEL
ASSY, DOME, INSULATION
SCR, M4X40, PPHMS, SST
86269870 CARPET MAINTAINER
SERIAL NO.
FROM
NOTES
31
Frame Deluxe
1
14
13
12
2
3
10
11
9
8
7
6
4
5
32
86269870 CARPET MAINTAINER
Frame Deluxe
REF
PART NO.
PRV NO.
QTY
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
86173050
86173040
86011610
86217930
86225340
86012550
86004570
86012440
86197520
86233090
86290790
86277600
86222360
86214830
70920
70919
34450
78952
44067
40011
20016
70882
58009
05263
3
3
1
1
1
1
1
1
1
1
1
1
1
1
SCR, M4 X 40 PPHMS, SS
SCR, M4 X 10 SHCSB BUTHD
ASSY, COVER, INSULATION, DLX
FRAME, 3.5, SINGLE MOTOR
TRAY, IRENEW MINI
JET, PROMAX, 11001
JET BODY, MINI PROMAX BODY
MANIFOLD, SPRAYER, DLX, IMX
HOSEBARB, 1/8MPT X 1/4 DL
CLAMP, 1/4 ID HOSE
SCR, M6 X 8, CP, BLK
SCR, M4 X 20, PHMS, SST
NUT, M4 X 0.7, U-CLAMP, 3MM PANEL
ASSY, DOME, INSULATION
86269870 CARPET MAINTAINER
SERIAL NO.
FROM
NOTES
33
Handle
26
23A
23B
3
19
18
17 16
25A
25B
4
3
15A
15B
24
21
14
5
3
13
6A
6B
22
1
12
2
8A
8B
11
9
10
20
7
34
86269870 CARPET MAINTAINER
Handle
SERIAL NO.
FROM
REF
PART NO.
PRV NO.
QTY
DESCRIPTION
1
2
3
4
5
6A
6B
7
8A
8B
9
10
11
12
13
14
15A
15B
16
17
18
19
20
21
22
86011380
86059580
86277600
86217230
86217220
86218680
86218510
86173070
86013820
86222650
86173180
86221800
86172640
86221810
86224970
86223640
86218690
86218520
86224680
86223450
86012940
86172820
86216890
86172870
86294260
38324
70882
38326
38325
38357
38321
70922
38354
70948
279992
57507
279993
730382
38332
38358
38322
730414
67620
70883
38327
70898
-
1
1
9
1
2
1
1
4
1
1
2
1
2
1
1
4
1
1
1
1
1
2
1
2
4
GRIP, HANDLE
CONSOLE, BOTTOM
SCR, M4X20, PPHMS, SST
CORD HOOK, UPPER
CORD HOOK, LOWER
HANDLE, EXTRUSION, LEFT
HANDLE, EXTRUSION, LEFT
SCR, M5X12, CSK.OVL,ISO 7047,SS
PIVOT CASTING, DLX
PIVOT CASTING
SCR, 10M8X55, SHLD, BLK
LIFTING CAM, LEFT
NUT, M8, LK, SST
LIFTING CAM, RIGHT
STRAP, SPRAYER HOLD DOWN
RUBBER STRAP HOOK
HANDLE, EXTRUSION, RIGHT
HANDLE, EXTRUSION, RIGHT
SPRING, COMP, 11.56D X 19.05L
RETAINER, SPRING, CORD HOOK
SCR, KA40X35, PT OVAL, WN1412, PL
SCR, M5X20, PPHMS, SST
CONSOLE, TOP
SCR, M4X14, PPHMS, ISO7045, SST
SCR, M5X12, W/LOCTITE
23A
86305580
-
1
CONSOLE, BOTTOM, DLX
**
23B
86293330
-
1
CONSOLE, BOTTOM
**
24
86308740
-
4
SCR, M5X30,CSK, OVL, ISO7047,SS
**
25A
86293340
-
1
CONSOLE, TOP
**
25B
86305590
-
1
CONSOLE, TOP
**
26
86299750
-
1
GRIP, HANDLE
**
NOTES
DELUXE ONLY
DELUXE ONLY
DELUXE ONLY
DELUXE 110V
& BASIC 110V
DELUXE 230V
& BASIC 230V
DELUXE 110V
& BASIC 110V
DELUXE 230V
& BASIC 230V
*See Serial Number Page
**Call Manufacturer For Serial Number
86269870 CARPET MAINTAINER
35
Hopper
3
4
5
6
7
2
2
1
36
86269870 CARPET MAINTAINER
Hopper
REF
PART NO.
PRV NO.
QTY
1
2
3
4
5
6
7
86214790
86173040
86214800
86173080
86216310
86172630
86217450
41584
70919
41585
70933
140977
57314
270709
1
10
1
1
1
1
1
DESCRIPTION
SERIAL NO.
FROM
NOTES
ASM, GUIDE, HOPPER
SCR, M4X10, BSHCS, SST
ASM, HOPPER FRAME & PLATE
SCR, 4.2 X 9.5, TAP, ZN
BUMPER, STOP, HOPPER
NUT, M4, LK, SST
COVER, FRONT, HOPPER
86269870 CARPET MAINTAINER
37
Motor
7
6
5
8
4
9
3
10
1
11
13
14
15A
15B
16
17
2
18
38
86269870 CARPET MAINTAINER
12
Motor
REF PART NO. PRV NO. QTY
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15A
15B
86215320
86215300
86215960
86173310
86173060
86217890
86217590
86173090
86222530
86291480
86173100
86173180
86224620
86215950
86222200
86222210
11058
11055
140979
87499
70921
34451
62647
70934
66869
70935
70948
730376
140978
54206
54216
1
1
1
4
3
4
2
1
1
1
1
1
1
1
1
1
BELT, HTD, 15MM X 300, 60 TOOTH, RH
BELT, HTD, 15MM X 325, 65 TOOTH, LH
BRKT, MTR MOUNT, RH
WASHER, SPRING LK, 6MM, SS
SCR, SHCS, M6X60, SST
FLANGE, BRG, PIVOT
CVR PLATE, 1.5MM THK, PLASTIC
SCR, SHCS, M6X80, SST
PEDAL, FOOT, HANDLE RELEASE
BRKT, FOOT PEDAL, SWITCH
SCR, M3X6, BSHCS, SST
SCR, 10M8X55, SHLD, BLK
SPRING, TORSION, 19.38 OD
BRKT, MTR MOUNT, LH
MOTOR, SINGLE, 3.5" DIA
MOTOR, 230V, IMIE
-
86216180
141057
1
BRUSH SET, 120V VAC, IM
16
17
18
86223780
86223340
86018550
70896
64124
70949
2
2
1
SCR, M4X8, CP, BLK
PULLEY, HTD, 5MM, 15W, 18T
SCR, M6X20, CP, BLK
86269870 CARPET MAINTAINER
SERIAL NO.
FROM
NOTES
120V ONLY
230V ONLY
120V & 230V,
NOT SHOWN
39
Rear Wheel
5
4
3
2
1
40
86269870 CARPET MAINTAINER
Rear Wheel
REF
PART NO.
PRV NO.
QTY
1
2
3
4
5
86172790
86216450
86011020
86173300
86172640
70867
140942
89202
87495
57507
2
4
2
4
2
DESCRIPTION
SERIAL NO.
FROM
NOTES
SCR, SHCS, M8X50, ISO4762, BLK
BUSHING, 11.25MM X 8.0MM, SST
WHEEL, 3" DIA. CUSHION RUBBER
WASHER, M8, FL, ISO7089, SST
NUT, M8, LK, ISO7040, SST
86269870 CARPET MAINTAINER
41
Solution Tank - Deluxe
-A-
1
2
3
4
25
5
6
16
8
19
9
24
10
12
23
31
13
21
14A
14B
-B22
15
-C- 17
13
7
30
27
-B-
-A-
-C-
20
19
42
31
29
15
26 21
-D-
-D-
18
28
86269870 CARPET MAINTAINER
11
Solution Tank - Deluxe
REF
PART NO.
PRV NO.
QTY
1
2
3
4
5
6
7
8
9
10
11
12
13
14A
14B
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
86299710
86299720
86012500
86219230
86225300
86013850
86172820
86012570
86012940
86216780
86172870
86217560
86012520
86201120
86201110
86240520
86172990
86013840
86217550
86012530
86012560
86233090
86012970
86006770
86224970
86012470
86290030
86290010
86290020
86299320
86225320
86010640
41581
75489
70883
27909
70898
41577
250-78A
250-78
40097
70913
41576
20016
70323
730382
78601
87016
1
1
1
1
1
3
3
1
5
2
2
1
2
1
1
4
3
1
1
2
1
4
2
1
1
1
1
1
1
1
1
2
DESCRIPTION
CPLR, BODY, 1/4" BARB, GRY
CPLR, PNL MNT, 1/4" BARB, GRY
SEAL, COUPLER, EPDM RUBBER
HOSE, SUCTION, TANK, DELUXE
TANK, DLX (MACH)
WASHER, M6, FNDR, SS
SCR, M5 X 20, PHMS, ISO7045, SST
STRAP, CHEMICAL BOTTLES, DLX
SCR, KA40X35, PT OVL, PL
CLAMP, TUBE 1/4”
SCR, M4X14 PHMS, SST
COVER, PUMP, TOP, DELUXE
GASKET, SEAL, NEOPRENE, RBR
PUMP, 220/240V 50HZ FLOJET
PUMP, 110/120 60HZ FLOJET
HOSEBARB, 1/8MPT X 1/4 90D
SCR, M6 X 12 BHCS, ISO 7380, SS
WASHER SPRING LCK, SMM
COVER, PUMP, DELUXE
GROMMET, 9.3MM ID X 23MM OD
STRAINER, SMALL, 60 MESH
CLAMP, 1/4 ID HOSE
WASHER, M5, FNDR, SS
SCR, 10-32 X 1/4 PHTR PLTD
STRAP, SPRAYER HOLD DOWN
CAP, 2-1/4, POWER GRIP
HOSE, 3/8OD X 1/4ID URTHN X 30”
HOSE, 3/8OD X 1/4ID URTHN X 8”
HOSE, 3/8OD X 1/4ID URTHN X 27”
LABEL, GROUND SYMBOL
TIE-CABLE, NYLON
WASHER, #10 LOCK EXT STAR SS
86269870 CARPET MAINTAINER
SERIAL NO.
FROM
NOTES
230V
110V
43
Wiring 120V
BLK
WHT
GRN
GRN
ORG
RED
PUR
ORG
BLK
WHT
GRN
ORG
N.C.
N.O.
RED
GREEN
1
5
GRN
RED
PUR
ORG
BLK
WHT
GRN
3
ORG
ORG
2
BLK
N.C.
ORG
BLK
4
BLK
RECTIFIER
RED
N
WHT
WHT
MOTOR
RELAY
8
7
6
5
4
3
2
1
BLK
RED
PUR
ORG
44
86269870 CARPET MAINTAINER
Wiring 120V
REF
PART NO.
PRV NO.
QTY
1
2
3
4
5
86218820
86226220
86226260
86226270
86226280
41563
880462
880468
880469
880471
1
1
1
1
1
DESCRIPTION
SERIAL NO.
FROM
NOTES
HARNESS, MAIN
WIRE, 10" BLK/18 76040
WIRE, 15" ORG/18 76040 X 76040
WIRE, 18" ORG/18
WIRE, 9" BLK/18 76040 X 76040
86269870 CARPET MAINTAINER
45
Wiring 230V
GRN
GRN
RED
ORG
BRN
BLU
RED
GREEN
ON/OFF
BLK
PUR
ORG
BLK
WHT
GRN
N.O.
1
GRN
ORG
ORG
N.C.
ORG
6
2
PUR
BLK
BLK
3
ORG
RED
BLK
WHT
GRN
5
7
4
BLU
BLK
BRN
RED
RECTIFIER
N
WHT
RELAY
8
7
6
5
4
3
2
1
MOTOR
BLK
RED
PUR
ORG
46
86269870 CARPET MAINTAINER
Wiring 230V
REF
PART NO.
PRV NO.
QTY
1
2
3
4
5
6
7
86218880
86226220
86226260
86226270
86226280
86302450
86310150
41594
880462
880468
880469
880471
-
1
1
1
1
1
1
1
DESCRIPTION
SERIAL NO.
FROM
NOTES
HARNESS, MAIN, 230VAC
WIRE, 10" BLK/18 76040
WIRE, 15" ORG/18 76040 X 76040
WIRE, 18" ORG/18
WIRE, 9" BLK/18 76040 X 76040
ASM, FILTER, EMI MAIN
ASSY, FILTER, EMI MOTOR
86269870 CARPET MAINTAINER
47
Wiring 120V - Deluxe
BLK
BLK
N.O.
BLUE
BLK
BLK
N.O.
BLUE
8
BLK
BLK
BLK
BLK
BLK
WHT
BLK
BLK
WHT
WHT
GRN
WHT
GRN
N.C.
N.O.
RED
GREEN
WHT
BLK
RED
PUR
ORG
BLK
WHT
GRN
ORG
ORG
6
5
GRN
3
RED
PUR
ORG
BLK
WHT
GRN
1
ORG
BLK
9
ORG
N.C.
ORG
PUMP MOTOR
4
2
BLK
WHT
BLK
BLK
RECTIFIER
RED
N
GRN
WHT
WHT
MOTOR
RELAY
8
7
6
5
BLK
4
3
BLK
2
1
RED
PUR
ORG
48
86269870 CARPET MAINTAINER
7
Wiring 120V - Deluxe
REF
PART NO.
PRV NO.
QTY
1
2
3
4
5
6
7
8
9
86218820
86226220
86226260
86226270
86226280
86013120
86013090
86013110
86013950
41563
880462
880468
880469
880471
-
1
1
1
1
1
1
1
1
1
DESCRIPTION
SERIAL NO.
FROM
NOTES
HARNESS, MAIN
WIRE, 10" BLK/18 76040
WIRE, 15" ORG/18 76040 X 76040
WIRE, 18" ORG/18
WIRE, 9" BLK/18 76040 X 76040
HARNESS, PUMP HOUSING, DLX
WIRE, 9.5" GRN/18
WIRE, 4 W/WIRE JOINT, BLK
WIRE ASSY, W/2 PIN CONN, DLX
86269870 CARPET MAINTAINER
49
Wiring 230V - Deluxe
BLK
BLK
N.O.
BLUE
BLK
BLK
N.O.
BLUE
11
BLK
BLK
BLK
BLK
BLK
WHT
WHT
WHT
GRN
GRN
RED
ORG
BLU
N.O.
GREEN
ON/OFF
BLK
RED
PUR
ORG
BLK
WHT
GRN
WHT
BLK
BRN
9
5
3
RED
BLK
WHT
GRN
1
ORG
GRN
6
PUR
2
BLK
12
ORG
N.C.
ORG
BLK
PUMP MOTOR
7
4
WHT
BLK
BLU
BLK
BRN
RED
RECTIFIER
N
GRN
WHT
10
RELAY
8
7
6
5
4
3
2
1
WHT
MOTOR
BLK
RED
PUR
ORG
50
86269870 CARPET MAINTAINER
Wiring 230V - Deluxe
REF
PART NO.
PRV NO.
QTY
DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
86218880
86226220
86226260
86226270
86226280
86302450
86310150
OPEN
86306770
86013090
86306760
86013950
41594
880462
880468
880469
880471
-
1
1
1
1
1
1
1
1
1
1
1
HARNESS, MAIN, 230VAC, IMIE
WIRE, 10" BLK/18 76040 X 76040
WIRE, ORG/18 76040 X 76040
WIRE, 18" ORG/18 76040 X 76040
WIRE, 9" BLK/18 76040 X 76040
ASM, FILTER, EMI MAIN
ASSY, FILTER, EMI MTR
HARNESS, PUMP HOUSING, DLX 230
WIRE, 9.5" GRN/18
WIRE, 4 W/WIRE JOINT, BLK
WIRE ASSY, W/2 PIN CONN, DLX
86269870 CARPET MAINTAINER
SERIAL NO.
FROM
NOTES
51
Suggested Spare Parts
52
PART NO.
PRV NO.
86216180
86215800
86215320
86214850
86217230
86224970
86002010
86217120
86217200
86223390
86291860
86215670
86215710
86012470
86012550
86012570
86295190
86292780
86295150
86295180
86299810
86299830
141057
11055
11058
12544
38326
730382
14942
23729
23738
67488
140839
141046
-
DESCRIPTION
BRUSH SET, MTR, 54206/54216
BELT, HTD, 15MM X 325, 65 TOOTH
BELT, HTD, 15MM X 300, 60 TOOTH
ASSY, BRUSH & HUB
CORD HOOK, UPPER
STRAP, SPRAYER HOLD DOWN
BOOT, 3/8 CIRCUIT BREAKER
CORD SET, 10/3 X 40FT SITW
CORD SET, EURO 1.0MM X 40 BLK
RECTIFIER, 50A 600V BRIDGE
SWITCH, 125VAC SP NC NO-ROLLER
BREAKER, 8A VDE CIRCUIT
BREAKER, 5A VDE CIRCUIT
CAP, 2-1/4, POWER GRIP
JET, PROMAX, 11001
STRAP, CHEMICAL BOTTLES, DLX
ASM, BUTTON BLUE, W/BEZEL
SWITCH, TONELUCK
ASM, BUTTON, RED, W/BEZEL
ASM, BUTTON, GREEN, W/BEZEL
SWITCH, BLACK, ROCKER, DPST
COVER, SWITCH, PVC
86269870 CARPET MAINTAINER
SERIAL NO.
FROM
NOTES
120V ONLY
230V ONLY
120V ONLY
230V ONLY
DELUXE ONLY
DELUXE ONLY
DELUXE ONLY
Serial Numbers
REF.
NO.
1
MODEL: SERIAL #
IM: 10066360000690 - IMX: 10066400000781
86269870 CARPET MAINTAINER
53