QUICK START INSTRUCTIONS Beyer 104 1024 x 768

QUICK START INSTRUCTIONS
ISU MEDIA ENHANCED CLASSROOMS
Beyer 104
PROJECTOR RESOLUTION
PROJECTOR TYPE
IP #
1024 x 768
(1600 x 1200
Hitachi CP-X880
129.186.132.1
PROJECTOR ON / TIMER RESET
VOLUME UP
DVD
VCR
LAPTOP
VOLUME DOWN
PROJECTOR OFF
SP CONTROLS SMARTPANEL
The SP Controls SmartPanel controls the video projector's functions. Pressing a button on the
SmartPanel sends a command to the video projector. Each command takes a few seconds to
execute; after pressing any button on the SmartPanel, wait at least 5 seconds before pressing
another button.
The SmartPanel has an auto-shutoff timer. When the PROJECTOR ON button is pressed, the
panel sets a 3 hour timer. The video projector power automatically switches OFF after 3 hours
unless the timer is reset. The timer may be reset any time the video projector power is ON. To
reset the timer, press any button on the SmartPanel EXCEPT the PROJECTOR OFF button.
TO OPERATE THE MEDIA CONTROL SYSTEM (SMARTPANEL) FOR COMPUTER DISPLAY
PERFORM THE OPERATIONS IN THIS ORDER:
1. Locate the SmartPanel's PROJECTOR ON button and press it to switch the video projector ON. Wait 15 seconds to
verify that the projector is ON. A red Warm-up LED on the SmartPanel will flash while the projector warms up; a
green Ready LED will be steadily illuminated when the projector is ready to use.
2. Select the LAPTOP input on the SmartPanel.
3. Locate the VGA cable and connect it to your computer and to the LAPTOP jack on the equipment rack inside
the media cabinet.
4. Switch the computer power ON. Note: the video projector power must be on and the computer must be connected
before the computer power is switched on.
5. Enable the external video display on your computer. Consult your computer documentation for instructions.
6. Locate the SmartPanel's PROJECTOR OFF button and press it to switch the video projector OFF when you are finished.
NO
1.
2.
3.
IMAGE?
Verify that the video projector power is on.
Verify that the LAPTOP input is selected on the SmartPanel.
Restart the computer.
NEED ASSISTANCE? CALL 294-8026.
THE NEAREST AVAILABLE PHONE IS LOCATED IN THE SECOND FLOOR HALLWAY ON THE SOUTH
SIDE OF THE BUILDING (JUST EAST OF THE TROPHY CASES).
printed August 27, 2003
roomhelp@iastate.edu
www.itc.iastate.edu
QUICK START INSTRUCTIONS
Beyer 104
ISU MEDIA ENHANCED CLASSROOMS
TO OPERATE THE MEDIA CONTROL SYSTEM (SMARTPANEL) FOR VIDEO DISPLAY
PERFORM THE OPERATIONS IN THIS ORDER:
1. Locate the SmartPanel's PROJECTOR ON button and press it to switch the video projector ON. Wait 15 seconds to
verify that the projector is ON. A red Warm-up LED on the SmartPanel will flash while the projector warms up; a
green Ready LED will be steadily illuminated when the projector is ready to use.
2. Select the desired input on the SmartPanel.
3. Locate the desired video source and switch its power ON.
4. Load the video tape, DVD, or other desired media.
5. Adjust the general audio volume. See below for audio instructions.
6. Locate the SmartPanel's PROJECTOR OFF button and press it to switch the video projector OFF when you are finished.
NO IMAGE?
1. Verify that the video projector power is ON.
2. Verify that the correct input is selected on the on the SmartPanel.
TO OPERATE THE AUDIO AMPLIFIER
The audio amplifier in this room has been preset for optimum operation and cannot be adjusted by users. To
increase or decrease the general audio volume, use the volume control buttons on the SmartPanel. To increase the
volume, press the VOLUME UP button. To decrease the volume, press the VOLUME DOWN button.
VOLUME UP
VOLUME DOWN
TO ACCESS THE SMARTPANEL'S SPECIAL FUNCTIONS
The SmartPanel has some built-in special functions. To access these functions, press and hold the SmartPanel's
PROJECTOR ON button and then press the button for the function you wish to use.
PROJECTOR ON
FOCUS
UP
FOCUS
DOWN
AUTO (use to optimize
IMAGE computer display)
NEED ASSISTANCE?
CALL 294-8026.
roomhelp@iastate.edu
printed August 27, 2003