3-Manual Organ
WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to the
presence of uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the product.
CAUTION
ATTENTION: RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS.
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
WARNING - When using electric products, basic precautions should always be followed, including the following:
1.
2.
3.
4.
5.
6.
7.
8.
9.
Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with a dry cloth.
Do not block any of the ventilation openings. Install in
accordance with the manufacturers instructions.
Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided plug
does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11. Only use attachments/accessories specified
by the manufacturer.
12. Unplug this apparatus during lightning storms or when
unused for long periods of time.
13. Refer all servicing to qualified service personnel. Servicing
is required when the apparatus has been damaged in any
way, such as power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.
For the U.K.
WARNING:
THIS APPARATUS MUST BE EARTHED
IMPORTANT: THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE.
GREEN-AND-YELLOW: EARTH, BLUE: NEUTRAL, BROWN: LIVE
As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying
the terminals in your plug, proceed as follows:
The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked by the
letter E or by the safety earth symbol or coloured GREEN or GREEN-AND-YELLOW.
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.
Before using this unit, carefully read the sections entitled: “IMPORTANT SAFETY INSTRUCTIONS” (p. 2), “USING THE UNIT SAFELY”
(p. 3), and “IMPORTANT NOTES” (p. 5). These sections provide important information concerning the proper operation of the unit.
Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new unit, Owner’s Manual
should be read in its entirety. The manual should be saved and kept on hand as a convenient reference.
2
USING THE UNIT SAFELY
About
WARNING and
CAUTION Notices
Used for instructions intended to alert the
user to the risk of death or severe injury
should the unit be used improperly.
Used for instructions intended to alert the
user to the risk of injury or material
damage should the unit be used
improperly.
* Material damage refers to damage or
other adverse effects caused with
respect to the home and all its
furnishings, as well to domestic animals
or pets.
About the Symbols
The symbol alerts the user to important instructions or
warnings.The specific meaning of the symbol is
determined by the design contained within the triangle. In
the case of the symbol at left, it is used for general
cautions, warnings, or alerts to danger.
The symbol alerts the user to items that must never be
carried out (are forbidden). The specific thing that must
not be done is indicated by the design contained within
the circle. In the case of the symbol at left, it means that
the unit must never be disassembled.
The symbol alerts the user to things that must be
carried out. The specific thing that must be done is
indicated by the design contained within the circle. In the
case of the symbol at left, it means that the power-cord
plug must be unplugged from the outlet.
ALWAYS OBSERVE THE FOLLOWING
WARNING
Make sure that the power cord is grounded
Connect mains plug of this model to a
mains socket outlet with a protective
earthing connection.
Do not disassemble or modify by yourself
Do not open or perform any internal
modifications on the unit.
WARNING
Do not bend the power cord or place heavy objects
on it
Turn off the unit if an abnormality or malfunction
occurs
Do not excessively twist or bend the
power cord, nor place heavy objects
on it. Doing so can damage the cord,
producing severed elements and short
circuits. Damaged cords are fire and
shock hazards!
Immediately turn the unit off, remove the
power cord from the outlet, and request
servicing by your retailer, or Rodgers
Instruments Corporation, as listed on the
“Notice to Users” (p. 6) page when:
Avoid extended use at high volume
Do not repair or replace parts by yourself
Do not attempt to repair the unit, or
replace parts within it (except when this
manual provides specific instructions
directing you to do so). Refer all servicing
to your retailer, or Rodgers Instruments
Corporation, as listed on the “Notice to
Users” (p. 6).
Do not use or store in the following types of
locations
• Subject to temperature extremes
(e.g., direct sunlight in an enclosed
vehicle, near a heating duct, on top of
heat-generating equipment); or are
• Damp (e.g., baths, washrooms, on wet
floors); or are
• Exposed to steam or smoke; or are
• Exposed to rain; or are
• Dusty or sandy; or are
• Subject to high levels of vibration and
shakiness.
Connect the power cord to an outlet of the correct
voltage
The unit should be connected to a power
supply only of the type described as
marked under the keyboard deck of unit.
• The power-supply cord or the plug has
been damaged; or
This unit, either alone or in combination
with an amplifier and headphones or
speakers, may be capable of producing
sound levels that could cause permanent
hearing loss. Do not operate for a long
period of time at a high volume level, or
at a level that is uncomfortable. If you
experience any hearing loss or ringing
in the ears, you should immediately
stop using the unit, and consult an
audiologist.
• If smoke or unusual odor occurs; or
Don’t allow foreign objects or liquids to enter unit;
never place containers with liquid on unit
Do not drop or subject to strong impact
Do not place containers containing liquid
(flower vases) on this product. Never
allow foreign objects (e.g., flammable
objects, coins, wires) or liquids (e.g.,
water or juice) to enter this product.
Doing so may cause short circuits, faulty
operation, or other malfunctions.
(Do not drop it!)
• Subject to salt exposure; or are
• Humid; or are
WARNING
Adults must provide supervision in places where
children are present
When using the unit in locations where
children are present, be careful so no
mishandling of the unit can take place.
An adult should always be on hand to
provide supervision and guidance.
• Objects have fallen into, or liquid has
been spilled onto the unit; or
• The unit has been exposed to rain (or
otherwise has become wet); or
• The unit does not appear to operate
normally or exhibits a marked change
in performance.
Protect the unit from strong impact.
Do not share an outlet with an unreasonable
number of other devices
Do not force the unit’s power-supply cord
to share an outlet with an unreasonable
number of other devices. Be especially
careful when using extension cords—the
total power used by all devices you have
connected to the extension cord’s outlet
must never exceed the power rating
(watts/amperes) for the extension cord.
Excessive loads can cause the insulation
on the cord to heat up and eventually
melt through.
Do not use overseas
Before using the unit in a foreign country,
consult with your retailer, or Rodgers
Instruments Corporation, as listed on the
“Notice to Users” (p. 6).
3
USING THE UNIT SAFELY
CAUTION
Place in a well ventilated location
Take care not to get fingers pinched by lid
The unit should be located so that its
location or position does not interfere
with its proper ventilation.
Be careful so you don’t get your fingers
pinched when you handle any moving
parts such as the following. Adult
supervision is recommended whenever
small children use the unit.
Grasp the plug when connecting or disconnecting
the power cord
Always grasp only the plug on the
power-supply cord when plugging into,
or unplugging from, an outlet.
Periodically clean the power cord’s plug
At regular intervals, you should unplug
the power plug and clean it by using
a dry cloth to wipe all dust and other
accumulations away from its prongs.
Also, disconnect the power plug from
the power outlet whenever the unit is to
remain unused for an extended period of
time. Any accumulation of dust between
the power plug and the power outlet can
result in poor insulation and lead to fire.
Manage cables for safety
Try to prevent cords and cables from
becoming entangled. Also, all cords and
cables should be placed so they are out
of the reach of children.
Avoid climbing on top of the unit, or placing heavy
objects on it
Never climb on top of, nor place heavy
objects on the unit.
Do not connect or disconnect the power cord with
wet hands
Never handle the power cord or its
plugs with wet hands when plugging
into, or unplugging from, an outlet.
Cautions when moving this unit
Since this product is very heavy, you
must make sure that a sufficient number
of people are on hand to help, so you can
lift and move it safely, without causing
strain. Make sure to have a firm grip,
to protect yourself from injury and the
instrument from damage.
If you need to move the instrument,
consult with your retailer, or Rodgers
Instruments Corporation, as listed on the
“Notice to Users” (p. 6).
Unplug the power cord from the outlet before
cleaning
Before cleaning the unit, turn it off and
unplug the power cord from the outlet.
If there is a possibility of lightning strike, disconnect
the power cord from the outlet
Whenever you suspect the possibility of
lightning in your area, pull the plug on
the power cord out of the outlet.
4
CAUTION
• Lid
Precautions concerning use of bench
When using the bench, please observe
the following points:
• Do not allow two or more persons to sit
on the bench.
• Do not adjust the height while sitting
on the bench.
Do not remove the speaker grille and speaker
Do not remove the speaker grille and
speaker by any means. Speaker not user
replaceable. Shock hazardous voltages
and currents are present inside the
enclosure.
IMPORTANT NOTES
Power Supply
• Do not connect this unit to same electrical outlet
that is being used by an electrical appliance that
is controlled by an inverter or a motor (such as a
refrigerator, washing machine, microwave oven, or
air conditioner). Depending on the way in which
the electrical appliance is used, power supply noise
may cause this unit to malfunction or may produce
audible noise. If it is not practical to use a separate
electrical outlet, connect a power supply noise filter
between this unit and the electrical outlet.
• To prevent malfunction and equipment failure,
always make sure to turn off the power on all your
equipment before you make any connections.
• Although the LCD and LEDs are switched off when
the unit is turned off, this does not mean that the
unit has been completely disconnected from the
source of power. If you need to turn off the power
completely, first turn off the unit’s switch, then
unplug the power cord from the power outlet. For
this reason, the outlet into which you choose to
connect the power cord’s plug should be one that
is within easy reach and readily accessible.
• With the factory settings, the power will
automatically be switched off 240 minutes after
you stop playing or operating the unit. If you don’t
want the unit to turn off automatically, change the
“Auto Off” (p. 17) setting to “OFF” as described on
“Making Settings in the Menus” (p. 12).
NOTE
The settings you were editing will be lost when the
unit is turned off. If you want to keep your settings,
you must save your settings before turning the
unit off.
Placement
• Using the unit near power amplifiers (or other
equipment containing large power transformers)
may induce hum. To alleviate the problem, change
the orientation of this unit; or move it farther away
from the source of interference.
• This device may interfere with radio and television
reception. Do not use this device in the vicinity of
such receivers.
• Noise may be produced if wireless communications
devices, such as cell phones, are operated in the
vicinity of this unit. Such noise could occur when
receiving or initiating a call, or while conversing.
Should you experience such problems, you should
relocate such wireless devices so they are at a
greater distance from this unit, or switch them off.
• Do not expose the unit to direct sunlight, place it
near devices that radiate heat, or otherwise subject
it to temperature extremes. Also, do not allow
lighting devices that normally are used while their
light source is very close to the unit (such as a piano
light), or powerful spotlights to shine upon the
same area of the unit for extended periods of time.
Excessive heat can deform or discolor the unit.
• Do not allow rubber, vinyl, or similar materials to
remain on this unit for long periods of time. Such
objects can discolor or otherwise harmfully affect
the finish.
• Do not allow objects to remain on top of the
keyboard or pedal board. This can be the cause
of malfunction, such as keys ceasing to produce
sound.
• Do not paste stickers, decals, or the like to this
instrument. Peeling such matter off the instrument
may damage the exterior finish.
• Do not put anything that contains water on this
unit. Also, avoid the use of insecticides, perfumes,
alcohol, nail polish, spray cans, etc., near the unit.
Swiftly wipe away any liquid that spills on the unit
using a dry, soft cloth.
Maintenance
• To clean the unit, use a dry, soft cloth; or one that
is slightly dampened. Try to wipe the entire surface
using an equal amount of strength, moving the
cloth along with the grain of the wood. Rubbing
too hard in the same area can damage the finish.
• Never use benzine, thinners, alcohol or solvents of
any kind, to avoid the possibility of discoloration
and/or deformation.
Repairs and Data
• Please be aware that all data contained in the
unit’s memory may be lost when the unit is sent for
repairs. Important data should always be backed
up the USB flash drive, or written down on paper
(when possible). During repairs, due care is taken
to avoid the loss of data. However, in certain cases
(such as when circuitry related to memory itself is
out of order), we regret that it may not be possible
to restore the data, and Rodgers assumes no
liability concerning such loss of data.
• Due to the structural design of this instrument,
small pets or other animals could end up getting
trapped inside it. If such a situation is encountered,
you must immediately turn off the unit and
disconnect the power cord from the outlet. You
should then consult with the retailer from whom
the instrument was purchased, or contact Rodgers
Instruments Corporation, as listed on the “Notice to
Users” (p. 6).
• When opening or closing the lid, please be careful
not to get your fingers pinched between the
movable part and the panel.
• The explanations in this manual include
illustrations that depict what should typically be
shown by the display.
Note, however, that your unit may incorporate
a newer, enhanced version of the system (e.g.,
includes newer sounds), so what you actually see
in the display may not always match what appears
in the manual.
Before Using External Memories
Using External Memories
• Carefully insert the USB flash drive all the way
in—until it is firmly in place.
Additional Precautions
• Please be aware that the contents of memory can
be irretrievably lost as a result of a malfunction,
or the improper operation of the unit. To protect
yourself against the risk of loosing important data,
we recommend that you periodically save a backup
copy of important data you have stored in the USB
flash drive.
• Unfortunately, it may be impossible to restore
the contents of data that was stored in the unit’s
memory or USB flash drive once it has been
lost. Rodgers Corporation assumes no liability
concerning such loss of data.
• Use a reasonable amount of care when using the
unit’s buttons, sliders, or other controls; and when
using its jacks and connectors. Rough handling can
lead to malfunctions.
• Never strike or apply strong pressure to the display.
• When disconnecting all cables, grasp the connector
itself—never pull on the cable. This way you will
avoid causing shorts, or damage to the cable’s
internal elements.
• A small amount of heat will radiate from the unit
during normal operation.
• To avoid disturbing others nearby, try to keep the
unit’s volume at reasonable levels. You may prefer
to use headphones, so you do not need to be
concerned about those around you.
• Never touch the terminals of the USB flash drive.
Also, avoid getting the terminals dirty.
• USB flash drive is constructed using precision
components; handle the cards carefully, paying
particular note to the following.
• To prevent damage to the cards from static
electricity, be sure to discharge any static
electricity from your own body before handling
the cards.
• Do not touch or allow metal to come into contact
with the contact portion of the cards.
• Do not bend, drop, or subject cards to strong
shock or vibration.
• Do not keep cards in direct sunlight, in closed
vehicles, or other such locations.
• Do not allow cards to become wet.
• Do not disassemble or modify the cards.
• When you need to transport the unit, pack it in
shock-absorbent material. Transporting the unit
without doing so can cause it to become scratched
or damaged, and could lead to malfunction.
• Do not apply undue force to the music stand while
it is in use.
• Some connection cables contain resistors. Do not
use cables that incorporate resistors for connecting
to this unit. The use of such cables can cause the
sound level to be extremely low, or impossible
to hear. For information on cable specifications,
contact the manufacturer of the cable.
5
Contents
USING THE UNIT SAFELY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IMPORTANT NOTES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ABOUT THE PERFORMANCE TOUCH KEYBOARDS . . . . . . . . . . .
Quick Tour . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
5
7
8
About the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Contents of the Main Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
About Pistons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
About Toe Pistons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Display and Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
External Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Making Settings in the Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Menu List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Demo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
USB Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Hymn Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Song Recorder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Pitch/Tuning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Room Modeling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
USER/MIDI Coupler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Tremulant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Exp. Pedal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Crescendo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
MIDI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Save/Load (USB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Storing Your Settings (Customize) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Selecting Stops (Sounds). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Selecting a Sound Variation (Voice Palette) . . . . . . . . . . . . . . . . . . . . . . . 22
Storing a Combination of Stops . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Storing or Recalling a Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Storing a Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Recalling a Registration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Resetting the Sound Settings (General Cancel) . . . . . . . . . . . . . . . . . . . 23
Using Memory Banks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Storing the Combination of Memory Pistons as a Memory
Bank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Recalling a Registration from a Different Memory Bank . . . . . 24
Recalling Registrations Successively. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Using Memory Banks with USB Memory . . . . . . . . . . . . . . . . . . . . . . . . . 25
Preparing USB Flash Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Selecting USB Memory Folder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Storing the Combination of Memory Pistons as a Memory
Bank to USB Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Recalling a Registration from a Different Memory Bank from
USB Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Changing the Settings for FULL ORGAN. . . . . . . . . . . . . . . . . . . 26
Setting the Sound to be Played When the [FULL ORGAN]
Piston is Pressed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Setting Whether Tablet Illumination is On/Off When the
[FULL ORGAN] Piston is Pressed . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Changing the Settings for Crescendo . . . . . . . . . . . . . . . . . . . . . 26
Changing ORGAN TYPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Practicing Along with a Preset Song or Performance Data . 27
Selecting and Playing Back a Song . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Muting a Specific Division During Playback. . . . . . . . . . . . . . . . . 28
Playing Back a Specific Division as a Guide Tone . . . . . . . . . . . . 28
Recording Your Performances . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Recording a Song . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Play Back the Recorded Song . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Saving a Recorded Song . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Deleting a Recorded Song . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Copying a Saved Song . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Hymn Player . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Selecting Hymn or Prelude . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Selecting Hymn number. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Playing Hymn . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Playing Prelude . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Changing Hymn book . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Saving and Loading Settings on USB Flash Drive . . . . . . . . . . 33
Formatting USB Flash Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Deleting a Memory Bank from USB Flash Drive . . . . . . . . . . . . . . . . . . . 33
Copying a Memory Bank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Saving and Loading Voice Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Saving to USB Flash Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Loading a Voice Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Deleting a Voice Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Backing Up Data/Performing an Initialization . . . . . . . . . . . . . 35
Returning all Settings to the Factory-Set State (Factory Reset). . . . . 35
Backing Up/Loading Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Displaying the Version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
List of Shortcuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Notice to Users
Information in this document is subject to change without notice. No part of this manual may be translated into any language, stored in a retrieval
system, reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, for any purpose
without the express written permission of Rodgers Instruments Corporation.
RODGERS INSTRUMENTS CORPORATION
1300 N.E. 25th Avenue
Hillsboro, Oregon 97124
(503) 648-4181
http://www.rodgersinstruments.com/
RODGERS IN CANADA
5480 Parkwood Way
Richmond, B.C. V6V 2M4
Toll Free (877) 676-5263
6
Rodgers instruments are manufactured and protected under one or
more of the following U.S. patents: 4,622,878, 5,060,179, 5,087,798,
5,091,613, 5,225,619, 5,262,581, 5,508,472, 6,369,310, 6,399,868
©Copyright 2012. Rodgers Instruments Corporation, a member of the
Roland Group. All rights reserved. Printed in the United States of America.
QuickMenu™, Rodgers®, Rodgers Classic Organs®, Digital Dynamic Wind™,
Dimensional Sound Modeling®, Parallel Digital Imaging®, Voice Palette™,
DVM™, PDI™, TrueChimes™, and Trillium Masterpiece™ are trademarks or
registered trademarks of Rodgers Instruments Corporation , Hillsboro,
Oregon. RSS® is a registered trademark of the Roland Corporation.
ABOUT THE PERFORMANCE TOUCH KEYBOARDS
For generations, organ key tops were made from the best materials – ivory (for white keys) and ebony (for black keys). The Performance Touch keyboards
use the latest technologies to reproduce the touch and feel of these materials.
• Surfaces incorporate stripes of moisture-absorbing material for improved touch and playability.
• Keys feature a subtle gloss and understated coloring, enhancing the look and elegance.
• White keys are finished with a slight yellowish tinge for the look of real ivory.
ѥѥNote:
— To Ensure Usage in Optimal Conditions —
Handling…
• Do not write on the keyboard with any pen or other implement, and do not stamp or place any marking on the instrument. Ink will seep into the surface
lines and become unremovable.
• Do not affix stickers on the keyboard. You may be unable to remove stickers that use strong adhesives, and the adhesive may cause discoloration.
Care and Maintenance…
Please note the following points. Failure to do so may result in scratches on the surface finish, damaged gloss, or other discoloration or deformation.
• Gently wipe dirt and grime with soft cloth; do not rub the surfaces forcefully.
• To remove more serious grime, use a commercial keyboard cleaner not containing abrasives.
• Do not use benzene, paint thinner, or alcohol on the keys.
7
Quick Tour
Music Rest
Keyboard Cover
Power Switch
Headphone Jack
Tablets
Pistons
USB Memory
Connector
Organ Bench
Pedalboard
External Connectors
WARNING
ѥѥWith the factory settings, the power will automatically be switched off 240 minutes after you stop playing or operating the unit.
If the unit’s power has been turned off automatically, you can use the Power switch to turn the unit back on again.
If you don’t want the unit to turn off automatically, change the “Auto Off” (p. 17) setting to “OFF” as described on “Making Settings in the Menus” (p. 12)
ѥѥWhen turning the power on again, you must allow at least five seconds after power-off before you once again turn the power on. If you fail to allow enough time, the Auto Off
function might not be reset, preventing the power from turning on correctly.
8
Quick Tour
About the Display
Contents of the Main Screen
6
1
2
7
8
9
3
4
5
1.
General memory bank number
2.
General memory piston number
3.
Keyboard transposition status
Range (semitones)
-6–+5
4.
Reference pitch (master tuning)
Available Settings (Hz)
392: VERSAIL (VERSAILLES)
415: BAROQUE
440: MODERN (standard)
465: VENETIA (VENETIAN)
MEMO
You can also adjust this tuning within the range of the reference pitch.
5.
Temperament
Available Settings
EQUAL, WERCK., KIRN.1, KIRN.3, VALLO., MEAN.D, MEAN.E, PYTHG., M.BACH
6.
Displayed when the MIDI Visual Control function is on.
7.
Crescendo pedal status
8.
Volume of the MAN-III expression pedal
9.
Volume of the MAN-I expression pedal
9
Quick Tour
About Pistons
1
4
ZIMBEL
TREM
ORGAN
TYPE
TREM
USER
MIDI
PA
2
10
3
USER
MIDI
PB
5
M1
FLT
TREM
ALT
DFLT
STOPS
TREM
6
7
8
14
9
13
Piston
17
23
24
25
26
22
[NEXT] Piston
This successively load the registration stored at the
next general memory piston; e.g., 1 g 2 g 3 ([NEXT]
piston).
16
[DFLT STOPS] Piston
Press this piston; the settings will be reset to a state
in which no sound is selected and the variation
settings will also be reset for all tablets, restoring the
basic variation VP0 (Default Voice Palette). Refer to
“Selecting a Sound Variation (Voice Palette)” (p. 22)
17
MAN I Division Coupler
Piston
This piston causes the 1st manual to play the sound
of the MAN III division. It has the same function as
the MAN I division coupler tablets.
[INT AUDIO OFF] Piston
Turn this piston if you want to mute internal
speakers.
[MAIN OFF] Piston
This piston silences the main organ system.
[ANT ON] Piston
This piston activate an antiphonal speaker system.
An antiphonal speaker system is so named because
it is normally installed a substantial distance
from the main organ. This difference in physical
placement allows for a variety of effects.
All Expression Shoe
MAN III Piston
Turn this piston on if you want to assign MAN I, MAN
II and Pedal divisions to MAN III expression shoe.
20
[ALT CRESC] Piston
This Organ is equipped with two independent
Crescendo sequences, a Standard Crescendo and
an Alternate Crescendo. Pressing the [ALT CRESC]
reversible piston so that it lights engages the
Alternate Crescendo sequence. Refer to “Changing
the Settings for Crescendo” (p. 26).
21
[CHIMES] Piston
This piston allows you to play Chimes voice.
Bass Coupler [BASS]
Piston
This causes the lowest note played on the 2nd
manual to be sounded by the PEDAL division sound.
Melody Coupler [MEL
III] Piston
This causes the highest note played on the 2nd
manual to be sounded by the MAN III division
sound.
Melody Coupler [MEL
I] Piston
This causes the highest note played on the 2nd
manual to be sounded by the MAN I division sound.
4
General Memory
Pistons
Each of these pistons can store the combination of
sounds (registration) for the entire organ.
5
USER/MIDI Coupler
Pedal
This piston allows you to play User/MIDI coupler.
Refer to “USER/MIDI Coupler” (p. 15)
6
Memory Bank Select
[M–] Piston/[M+] Piston
[M1] Piston
Use these pistons when you want to switch memory
banks. [M1] piston allows you to switch memory
bank 1.
7
PEDAL Division
Coupler Piston
This piston causes the pedalboard to play the sound
of the MAN I–III division. It has the same function as
the PEDAL division coupler tablets.
Division Memory
Pistons
Each of these pistons can store the sound
(registration) for the MAN I -III division.
Tremulant Pistons
The tremulant effect adds vibrato (cyclic
modulation) to the sound of MAN I–III division. Refer
to “Tremulant” (p. 17).
This tremulants find best use in gospel, theatre and
evangelical music; the Flute Vibrato affects Flute
voices.
This Organ is equipped with two independent Flute
Tremulant settings, a Standard Flute Tremulant and
an Alternate Flute Tremulant. Pressing the [FLT TEM
ALT] reversible piston so that it lights engages the
Alternate Flute Tremulant. Refer to “Tremulant” (p. 17).
When the [PIPES OFF] piston is engaged, the
wind-blown pipe ranks are silenced.
18
19
ѥѥThis is used when an optional pipe system has
been connected.
When an [ANC ON] piston is engaged, digital voices
play from the stops which normally control pipe
voices. These digital voices are often referred to as
the “Ancillary.”
ѥѥThis is used when an optional pipe system has
been connected.
10
21
15
[SET] Piston
USER/MIDI Coupler
MAN I - III
HYMN
PLAYER
This piston causes the 2nd manual to play the sound
of the MAN I and MAN III division. It has the same
function as the MAN II division coupler tablets.
3
12
USER
MIDI
B
MAN II Division
Coupler Piston
This stores a combination of sounds (registration)
to a general memory piston or a division memory
piston.
[ANC ON] Piston
USER
MIDI
A
ALT
CRESC
14
This piston allows you to select Organ Type.
11
USER
MIDI
B
ALL
EXPR
Turn this piston on if you want to use the expression
pedal to adjust the volume of MAN II division and
PEDAL division.
[ORGAN TYPE] Piston
[PIPES OFF] Piston
USER
MIDI
A
20
MAN II & PEDAL
Enclosed Piston
2
10
USER
MIDI
B
19
13
This piston allows you to play Zimbelstern voice.
Flute Tremulant ALT
Piston
USER
MIDI
A
16
15
18
Piston
[ZIMBEL] Piston
9
12
Explanation
1
8
11
This piston allows you to play User/MIDI coupler.
Refer to “USER/MIDI Coupler” (p. 15).
22
23
24
Explanation
[HYMN PLAYER] Piston
This piston allows you to play a Hymn.
[STOP] Piston
This stops playback or recording of a song.
[PLAY/PAUSE] Piston
This starts or pauses playback of a song.
[REC] Piston
Use this when you want to record your playing.
Quick Tour
Piston
25
26
MEMO
Explanation
General Cancel [0]
Piston
This sets the organ to the condition in which all
tablets and couplers are cancelled, so that no
sounds are selected. It’s convenient to use this
piston when you want to specify a combination of
sounds from scratch.
[FULL ORGAN] Piston
FULL ORGAN controls allow you to engage full
organ quickly without canceling the registration
which is set.
About Toe Pistons
The settings for the volume balance of the organ’s speakers and
the satellite speakers can be stored in memory. For details, refer to
“Storing Your Settings (Customize)” (p. 21).
3.
[Value/Exit Menu] Knob
Turn: Adjusts a setting.
Press: Returns you to the previous menu, or cancels an operation.
4.
[Master Volume] Knob
This adjusts the volume of the entire organ.
5.
1
2
[Reverb] Knob
This adjusts the depth of reverberation.
External Connectors
3
Pedal/Piston
Explanation
1
Expression Pedal
The volume of MAN I/II/PEDAL is adjusted with the
left pedal, and the center pedal is used to adjust the
volume of MAN III.
2
Crescendo Pedal
This shoe gradually adds a predetermined selection of
stops as it is pressed forward.
1
1.
General Memory Piston 1–5
PEDAL Division Coupler Piston
3
10 x Toe Pistons
This piston causes the pedalboard to play the sound of
the MAN I–III division.
Full Organ Piston
2
3
OUTPUT L/MONO, R (Output) Jacks
You can connect an external amplified speaker system here so that the
sound of the organ is played from the connected speakers.
2.
INPUT L/MONO, R (Input) Jacks
You can connect an external sound module or similar device here so
that its sounds are heard from the organ’s speakers.
Display and Panel
3.
MIDI IN, OUT Connectors
You can connect external MIDI devices here to exchange performance
data with the organ.
1
ѥѥTo prevent malfunction and equipment failure, always turn down the
2
3
volume, and turn off all the units before making any connections.
ѥѥCarefully insert the USB flash drive all the way in-until it is firmly in
place.
4
5
ѥѥThis unit is equipped with a protection circuit. A brief interval (a few
seconds) after turning the unit on is required before it will operate
normally.
1.
Display
2.
[Select/Menu] Knob/[Satellite Volume] Knob
Various information is shown here.
Turn: Adjusts the volume of the satellite speakers. When you’re in a
menu screen for making detailed settings, turn this knob to
select the item you want to operate.
ѥѥBefore turning the unit on/off, always be sure to turn the volume
down. Even with the volume turned down, you might hear some
sound when switching the unit on/off. However, this is normal and
does not indicate a malfunction.
ѥѥIf you need to turn off the power completely, first turn off the unit, then
unplug the power cord from the power outlet. Refer to “Power Supply”
(p. 5).
Press: Takes you to a menu screen, or finalizes a setting item.
11
Making Settings in the Menus
Heres how to make settings using the menus. Perform these steps from
the main screen. For a list of the menu items, refer to the next page.
1.
4.
Turn the [Value/Exit Menu] knob to change the item’s setting.
Press the [Select/Menu] knob to access the menu.
To cancel the setting / to return to the previous menu...
Press the [Value/Exit Menu] knob.
2.
Turn the [Select/Menu] knob to select the item.
3.
Press the [Select/Menu] knob to enter the item.
5.
If a Yes/No confirmation screen appears, press the [SET]
piston to put the setting into effect.
Menu List
The settings shown below will revert to their default values when the organ’s power is turned off; however, with a number of the settings, you can have
their content be stored in memory even after the power is turned off.
Setting items marked with [S]
Can be stored in the SYSTEM group.
Setting items marked with [V]
Can be stored in the VOICING group.
Setting items marked with [P]
Settings can be stored on an individual piston basis.
Refer to “Storing Your Settings (Customize)” (p. 21).
Refer to “Storing or Recalling a Registration” (p. 23).
Demo
Listen to demo songs
ѥѥAll rights reserved. Unauthorized use of this material for purposes other than private, personal enjoyment is a violation of applicable laws.
ѥѥNo data for the music that is played will be output from MIDI OUT connector.
Menu item
Value
Group
Demo song group
Song
Demo song
Tempo
Tempo of the demo song
Satellite Volume
0–127
Explanation
Volume of the satellite speakers
USB Memory
Selecting a USB Memory folder
12
Menu item
Value
Explanation
Folder
A–Z
Selecting a USB Memory folder
Making Settings in the Menus
Hymn Player
Play back Hymn and Prelude
Menu item
Value
Explanation
Mode
–
Select Hymn or Prelude
Hymn number
–
Select Hymn number
Next
Play Mode [S]
Tempo
Intro, Verse
Select to play introduction or verse
VAR.
Prelude begins at a random selection and plays continuously
FIXED
Prelude begins at a predetermined selection and plays continuously
20-240
Tempo of the Hymn
Volume [S]
0%-100%
The volume of Hymn
Transpose
-6 – +5
Change the key of the song in semitone steps
Book [S]
–
Select Hymn book
Song Recorder
Recording, play back song, saving, deleting, and copying song data
Menu item
Source
Value
Explanation
USB
Play back song data from USB flash drive.
INTERNAL
Play back song data from internal memory.
PRESET
Play back built-in preset song (demo song).
Song
Name of the song
Tempo
Refer to “Beat” (p. 13)
Measure
Measure of the song
[Division Mute]
Refer to “Muting a Specific Division During Playback” and “Playing Back a Specific Division as a Guide Tone” (p. 28).
MAN-II
MUTE, GUIDE, PLAY
MAN-I
MUTE, GUIDE, PLAY
Pedal
MUTE, GUIDE, PLAY
Guide Volume [S]
1–10
Tempo of the song
Select the division that you want to mute.
Adjust the volume of the guide tone.
F16, P16, R16, F8, P8,
R8, F4, P4, R4
Guide Tone [S]
Playback
Transpose
Play Mode
Metronome
Volume
F: Flute,
P: Principal,
R: Reed,
Number: Footage
Choose the guide tone.
-6 – +5
The transpose function lets you shift the pitch in semitone steps.
OFF
Play back only the selected song.
CHAIN
Consecutively play back all the songs on the selected media.
OFF, 1–10
Volume of the metronome. Turn this “OFF” if you don’t want the metronome to sound.
Beat of the song or metronome
The range within which the tempo can be set will vary depending on the setting for Beat.
Beat
Beat
Tempo range
2/2
10–120
0/4, 2/4, 3/4, 4/4, 5/4,
6/4, 7/4
20–240
3/8
40–480
6/8, 9/8, 12/8
13–160
[Save Song]
Refer to “Saving a Recorded Song” (p. 29).
[Delete Song]
Refer to “Deleting a Recorded Song” (p. 30).
[Copy Song]
Refer to “Copying a Saved Song” (p. 31).
13
Making Settings in the Menus
Pitch/Tuning
Settings for pitch, Temperament, Tuning, and Transpose
Menu item
Value
Explanation
The reference pitch can be changed from “A=440.0 Hz” to “A=415.0 Hz” (Baroque pitch) or “A=392.0 Hz” (Versailles pitch).
Pitch
VERSAILLES
392 (Hz)
BAROQUE
415 (Hz)
MODERN
440 (Hz)
VENETIAN
465 (Hz)
Historical styles of music such as baroque can be played in the tunings that were used during that time.
Temperament
Tuning
EQUAL
(Equal temperament)
This temperament divides the octave into twelve equal intervals. Modulating to a different key will not affect the sonority of
the chords.
WERCK.
(Werckmeister)
This temperament combines the meantone temperament and the Pythagorean temperament. It allows playing in all keys
(method 1, number 3).
KIRN.1
(Kirnberger 1)
This is an improvement of meantone temperament and just intonation to allow greater freedom of modulation. It allows
playing in all keys (method 1).
KIRN.3
(Kirnberger 3)
This is a variation of Kirnberger 1 (method 3).
VALLO.
(Vallotti)
This is a relatively recent temperament. It is close to equal temperament but has a certain amount of just intonation, making
it easier to stay in tune with other instruments, and is thus frequently used for ensembles.
MEAN.D (Meantone
temperament)
This temperament is a partial compromise from just intonation in order to allow a certain degree of modulation. Preference
is given to the sonority in D#.
MEAN.E (Meantone
temperament)
This temperament is a partial compromise from just intonation in order to allow a certain degree of modulation. Preference
is given to the sonority in Eb.
PYTHG.
(Pythagorean tuning)
This is a system of tuning attributed to the philosopher Pythagoras, in which the fourth and fifth are pure. Chords including
the third will not sound smooth, but the melody will sound good.
M.BACH
(Modern Bach)
This is one of the recently researched temperaments from the era of Bach. It allows playing in all keys.
±100 cents
You can adjust this in a range of ±100 cents (a semitone) centered on the selected pitch.
The transpose function lets you shift the pitch in semitone steps without changing the keys you play on the keyboard.
Transpose
-6–+5
MEMO
From the main screen, while holding the [SET] piston, turn the [Value/Exit Menu] knob to change the transpose. From the main
screen, press [0] piston, transpose will also be turned off.
Room Modeling
Reverb settings
Menu item
Value
Explanation
By changing the type of reverberation you can experience the sensation of performing in a variety of locations.
Room Type [S]
CHAMBER
The reverberation of a pipe chamber
HALL
The reverberation of a hall
CHURCH
The reverberation of a church
CATHEDRAL
The reverberation of a cathedral
You can make additional changes to the reverberation by changing the wall type (the material out of which the wall is constructed).
Wall Type [S]
14
DRAPERY
Pleated curtains
WOOD
Wood
BRICK
Brick
MARBLE
Marble
Making Settings in the Menus
USER/MIDI Coupler
• Selecting sounds that are not available via the sound tablets and stops
• MIDI coupler settings
• Adjusting sounds
Menu item
Value
Division
MAN-I A, MAN-I B, MAN-II A, MAN-II B, PEDAL A, PEDAL B
ѥѥDetails of the available items will depend on the Source/MIDI CH setting.
Menu item
Value
Explanation
Source/MIDI CH
[V] [P]
USER
Internal sound generator
CH1–16
MIDI transmit channel
The range will depend on the division that is selected.
Source/MIDI CH = USER
Menu item
Value
Explanation
Name [V] [P]
Name of sound
Select by sound name
Volume [V] [P]
OFF, 0–127
Specifies the volume of the sound assigned to the [USER/MIDI] coupler.
Octave [V] [P]
-2–+2, NORMAL
Specifies the octave of the sound assigned to the [USER/MIDI] coupler.
Coarse Tune
[V] [P]
-12–+12
Adjusts the pitch in semitone steps.
Fine Tune [V] [P]
-50–+50
Adjusts the pitch in a range of ±50 cents
Warmth [V] [P]
-10–10
Adjusts the low-frequency tone for the sound assigned to the [USER/MIDI] coupler.
Presence [V] [P]
-10–10
Adjust the mid-frequency tone for the sound assigned to the [USER/MIDI] coupler.
Brilliance [V] [P]
-10–10
Adjusts the high-frequency tone for the sound assigned to the [USER/MIDI] coupler.
Reverb [V] [P]
OFF, 0–127
Velocity [V] [P]
Tweak the reverb depth for the sound assigned to the [USER/MIDI] coupler.
Normally set this “OFF.”
KBD
The keyboard’s velocity will be used
EXP
The expression pedal’s position will be used
2–127
The specified value will be used as the velocity
ѥѥVelocity can be applied only to orchestral sounds
Source/MIDI CH = CH1–16
Menu item
Value
Explanation
Name [V] [P]
Name of sound
Select by sound name (refer to “Tone Name [S]” (p. 19))
PC Number
[V] [P]
OFF, 001–128
Program change number
Bank MSB [V] [P]
OFF, 000–127
Bank select MSB
Bank LSB [V] [P]
OFF, 000–127
Bank select LSB
Volume [V] [P]
OFF, 0–127
Specifies the volume
Octave [V] [P]
-2–+2, NORMAL
Specifies the octave (pitch)
Reverb [V] [P]
OFF, 0–127
Specifies the depth of reverb
Chorus [V] [P]
OFF, 0–127
Specifies the depth of chorus
KBD
The keyboard’s velocity will be used
EXP
The expression pedal’s position will be used
2–127
The specified value will be used as the velocity
OFF, ON
Expression Pedal
Velocity [V] [P]
Expression [V] [P]
15
Making Settings in the Menus
About MIDI transmit channels
When the [USER/MIDI] coupler is off
Even when the [USER/MIDI] coupler is off, the performance data from
each division is transmitted on the following MIDI channels.
When the [USER/MIDI] coupler is on
As appropriate, you’ll need to change the MIDI reception settings on
the MIDI device that’s connected.
To avoid a conflict between the MIDI transmit channels of the various
[USER/MIDI] couplers, the MIDI transmit channels are fixed as follows.
Division (keyboard)
MAN-I (1st)
MAN-II (2nd)
MAN-III (3rd)
PEDAL (pedalboard)
Tablet name
MIDI transmit channel
USER MIDI A
CH4 (fixed)
USER MIDI B
CH8 (fixed)
USER MIDI A
CH1–CH16
USER MIDI B
CH5 (fixed)
USER MIDI A
CH2 (fixed)
USER MIDI B
CH6 (fixed)
USER MIDI A
CH3 (fixed)
USER MIDI B
CH7 (fixed)
Division (keyboard)
MIDI transmit channel
MAN-I (1st)
CH15 (fixed)
MAN-II (2nd)
CH12 (fixed)
MAN-III (3rd)
CH13 (fixed)
PEDAL (pedalboard)
CH14 (fixed)
ѥѥWhen using a [USER/MIDI] coupler to control an external MIDI sound
module, we recommend that you set your external MIDI device to not
receive messages on channels 12–15.
Console
• Screen contrast
• MEL and BASS coupler settings, and other settings
Menu item
Value
Explanation
Display Contrast
[S]
0–30
ѥѥThis setting will return to the default value when you turn off the power, but you can store the setting so that it will be
Adjust the Display Contrast
remembered even after the power is turned off. For details, refer to “Storing Your Settings (Customize)” (p. 21).
You are free to change the range in which the bass coupler will operate. The specified note and those below it will use the bass coupler.
Bass coupler
Bass Split [S]
Top key of the Bass coupler range
You are free to change the range in which the melody coupler will operate. The specified note and those above it will use the melody coupler, and
notes below it will not.
Melody coupler
Mel Split III [S]
Mel Split I [S]
Bottom key of the Melody coupler range
Blind [S]
16
BLIND
When the [FULL ORGAN] piston is pressed or Crescendo pedal is activated, tablet illumination is turned off.
VISIBLE
When the [FULL ORGAN] piston is pressed or Crescendo pedal is activated, tablet illumination is turned on.
OPERATE
When the [FULL ORGAN] piston is pressed or Crescendo pedal is activated, tablet illumination is turned on. Also you can
operate the tablets.
Making Settings in the Menus
Menu item
Value
Explanation
If this is set to “240 min,” the power will automatically turn off 240 minutes after the Organ was last operated.
NOTE
After Auto Off shut down, turn the power switch off. Wait at least five seconds, then turn the power switch on again.
Auto Off [S]
OFF, 10 min, 30 min,
240 min
WARNING
With the factory settings, the power will automatically be switched off 240 minutes after you stop playing or operating the
unit.
If you don’t want the unit to turn off automatically, change the “Auto Off” setting to “OFF.”
Music Rest Lamp
[S}
OFF, 1–16
Setting Music Rest and Pedalboard Lamp.
Piston lamp [S}
1–16
Setting Piston Tablet Lamp.
KBD Transfer [S]
OFF, ON
Exchange 1st keyboard and 2nd keyboard, it allows you to use French type Organ.
Tremulant
The tremulant effect adds vibrato (cyclic modulation) to the sound.
Menu item
Division
Value
Explanation
MAN-I
Sets the tremulant for MAN-I.
MAN-II
Sets the tremulant for MAN-II.
MAN-III
Sets the tremulant for MAN-III.
M-I FLUTE
Sets the flute tremulant for MAN-I.
M-II FLUTE
Sets the flute tremulant for MAN-II.
M-III FLUTE
Sets the flute tremulant for MAN-III.
M-I FLUTE2
Sets the flute tremulant 2 for MAN-I.
M-II FLUTE2
Sets the flute tremulant 2 for MAN-II.
M-III FLUTE2
Sets the flute tremulant 2 for MAN-III.
Depth [S]
0–127
With a setting of “0,” no tremulant will be applied. Increasing this value will make the tremulant deeper.
Rate [S]
0–127
A slow tremulant will be applied with a setting of “0,” and this will become faster as you increase the value.
Exp. Pedal
Expression pedal settings
Menu item
MAN-II/Pedal [P]
MAN-III [P]
Value
Explanation
OFF
Not affected by the expression pedal
ON
MAN-II and Pedal division are affected by the expression pedal
OFF
Not affected by the expression pedal
ON
MAN-III division is affected by the expression pedal
You can adjust the minimum volume that will be in effect when the expression pedal is at the minimum position.
Shutter [S]
PPPP
Least volume
PPP
Low volume
PP
Somewhat higher volume
UNENCL
Not affected by the expression pedal
The kick switch is located on the side of the expression pedal. You can assign a function to the kick switch.
Kick SW [S]
OFF
The kick switch will be off.
NEXT
This has the same function as the [NEXT] piston. It will switch to the adjacent general memory piston. Each time you press
the kick switch, the general memory piston will switch to the next higher number.
PREV
This has the same function as the [PREV] piston. It will switch to the adjacent general memory piston. Each time you press
the kick switch, the general memory piston will switch to the next lower number.
Sustain will be applied while you are pressing the switch.
SUSTAIN
ѥѥSustain can be applied only to some of the [USER/MIDI] coupler sounds and to the sounds of an external MIDI sound module.
ѥѥSustain will not be applied to the sounds of the organ.
17
Making Settings in the Menus
Crescendo
Crescendo settings
Menu item
Value
Explanation
Crescendo Step
0–63
Refer to “Changing the Settings for Crescendo” (p. 26).
Audio
External device settings
Menu item
Value
Explanation
Aux In Volume [S]
0–127
Adjusts the volume of the external audio device.
Aux In Reverb [S]
0–127
Adjusts the reverb depth for the external audio device.
Adjusts the volume that is output from the OUTPUT jacks.
Line Out Gain [S]
0–127
ѥѥThe volume balance for Master Volume and Line Out can be stored. For this reason, the value of the setting for Line Out Gain
can change depending on the value of Master Volume.
Adjusts the overall volume of the organ.
Master Volume [S]
KNOB, 1–127
When set to KNOB, the Master Volume knob can be used to perform the adjustment.
When set to a value from 1 through 127, the Master Volume knob and Line Out Gain will be disabled.
[Division Audio]
18
Adjusts the volume of the main and antiphonal speaker system.
Four different types of settings can be established depending on whether the [MAIN OFF] and [ANT ON] pistons have been pressed or not.
MAN-I to Main [S]
0–127
The volume of MAN-I to Main
MAN-I to Ant [S]
0–127
The volume of MAN-I to Antiphonal
MAN-II to Main [S]
0–127
The volume of MAN-II to Main
MAN-II to Ant [S]
0–127
The volume of MAN-II to Antiphonal
MAN-III to Main [S]
0–127
The volume of MAN-III to Main
MAN-III to Ant [S]
0–127
The volume of MAN-III to Antiphonal
PEDAL to Main [S]
0–127
The volume of Pedal to Main
PEDAL to Ant [S]
0–127
The volume of Pedal to Antiphonal
ORCH to Main [S]
0–127
The volume of Orchestra to Main
ORCH to Ant [S]
0–127
The volume of Orchestra to Antiphonal
AUX-IN to Main [S]
0–127
The volume of Aux in to Main
AUX-IN to Ant [S]
0–127
The volume of Aux in to Antiphonal
Reverb to Main [S]
0–127
The volume of Reverb to Main
Reverb to Ant [S]
0–127
The volume of Reverb to Antiphonal
Making Settings in the Menus
MIDI
MIDI settings
Menu item
Value
Explanation
When the organ is connected to a MIDI sequencer, change this setting to Local Off.
Local
OFF
Local Off: the keyboard is disconnected from the internal sound generator. No sound will be heard when you play the
keyboard.
ON
Local On: the keyboard is connected to the internal sound generator.
When using an [USER/MIDI] coupler with an MX-200 or GM2-compatible external MIDI sound module, you can make the sound names of your MX-200
or GM2-compatible sound module appear in the “USER/MIDI” screen.
Tone Name [S]
OFF
Tone name will not show.
MX200
The screen will show the name of the MX-200’s sound if an MX-200 is connected as an external MIDI sound module.
GM2
The screen will show the name of the GM2 sound if a GM2-compatible sound module is connected as an external MIDI
sound module.
When transmitting performance data via MIDI, you can specify the type of MIDI data that will be transmitted when you press a general memory piston
and division memory piston.
TX Piston [S]
OFF
MIDI data will not be transmitted.
STOP MAP
Data describing the details of the sounds that should be produced when that piston is pressed will be transmitted. If you’re
recording your performance into a MIDI sequencer, this will ensure that the sounds are reproduced accurately. However,
since a large amount of data is transmitted when you press the piston, the sounding of the first note-on after you press the
piston may be delayed in some cases.
PC
Only program changes indicating the current memory bank and the memory piston that was pressed will be transmitted.
If you’re recording your performance into a MIDI sequencer, the performance will not be accurately reproduced unless the
contents of the memory bank used during the performance match the contents during recording. However, since a large
amount of data will not be transmitted when you press the piston, there will be no significant delay in the first note-on after
you press the piston.
When external, MVC/V-LINK-compatible, audiovisual presentation equipment is connected, you’ll be able to control the imagery presented by such
equipment at the same time as you play the organ. When you press a general memory piston, messages used for video control will be transmitted from
the MIDI OUT connector. This allows you to control the imagery presented by the audiovisual equipment.
Visual Control
OFF
The MIDI Visual Control function is off.
MVC
MVC is on
V-LINK
V-LINK is on
Selecting sounds on your external MIDI
device
How sound names are displayed
If an MX-200 or a GM2 compatible sound module is connected, you
can set “Tone Name [S]” (p. 19) to the model of sound module you’re
using, so that the “USER/MIDI Coupler” screen’s “Name” field will show
the names of the sounds, allowing you to choose sounds by name.
Using the keyboard to select
You can use the following method to select sounds on your external
MIDI device.
1.
Turn on the desired [USER/MIDI] coupler.
2.
Set it like this: Source/MIDI CH = CH 1–16.
3.
Hold down the [SET] piston and play a note on the
keyboard and the pedalboard. The [USER/MIDI] coupler
will blink.
The program change corresponding to the note you played will
be transmitted, and the sound selection on your MIDI device will
change.
Each note of the keyboards corresponds to the following program
changes.
Keyboard
Tone name
Program change
1st keyboard
C2–C7
1–61
2nd keyboard
C2–C7
62–122
3rd keyboard
C2–F2
123–128
19
Making Settings in the Menus
Save/Load (USB)
Save/load the contents of the general memory pistons and voice setup, and format the USB flash drive
Menu item
Explanation
Copy Memory Bank
Refer to “Copying a Memory Bank” (p. 33).
Delete Memory Bank
Refer to “Deleting a Memory Bank from USB Flash Drive” (p. 33).
Save Voice Setup
Refer to “Saving and Loading Voice Setup” (p. 34).
Load Voice Setup
Refer to “Loading a Voice Setup” (p. 34).
Delete Voice Setup
Refer to “Deleting a Voice Setup” (p. 34).
Format USB Memory
Refer to “Formatting USB Flash Drive” (p. 33).
Utility
Backing Up Data/Performing an Initialization
20
Menu item
Explanation
Version
Refer to “Displaying the Version” (p. 35).
Back up/Restore
Refer to “Backing Up/Loading Data” (p. 35).
Factory Reset
Refer to “Returning all Settings to the Factory-Set State (Factory Reset)” (p. 35).
Making Settings in the Menus
Storing Your Settings (Customize)
The following settings will return to their default state when you switch off the organ’s power, but you can use the procedure described below to store
these settings.
Setting
Group
Default Voice Palettes (*)
“User/MIDI coupler” screen settings
VOICING
Loaded Voice Setup (p. 34)
“Room Modeling” screen settings
“Console” screen settings
“Tremulant” screen settings
“Exp. Pedal” screen settings
“Audio” screen settings
Satellite Volume settings
SYSTEM
“MIDI” screen settings
“Guide Tone” and “Guide Volume” settings in “Song
Recorder” screen
Hymn book
* What is the Default Voice Palette?
The “Default Voice Palettes” specifies which variation sound will be heard when you turn on a specific tablet.
If you specify the variation sounds that you frequently use, you’ll be able to play those variation sounds simply by selecting those tablets, without
needing to select the variation sounds.
1.
Hold down the [SET] piston and press the [0] piston.
Confirmation screen will appear
2.
Turn the [Value/Exit Menu] knob to choose the group.
• If you choose “VOICING,” the VOICING group settings will be saved.
• If you choose “SYSTEM,” the SYSTEM group settings will be saved.
3.
Press the [SET] piston to store the settings.
If you decide to cancel, press the [Value/Exit Menu] knob.
NOTE
ѥѥNever turn off the power before the storage has been completed. (Wait until the “Executing” indication is no longer shown.)
21
Selecting Stops (Sounds)
By pressing the sound tablets you can play a variety of pipe organ sounds. The sounds assigned to the tablets are called “stops.”
The sound tablets are organized into groups called “divisions.” These tablets are called “division tablets.”
If the indicator of a division tablet is lit, you’ll be able to play the corresponding stop.
Press the lower part of the tablet to
select the stop; the indicator is lit
Press the upper part of the tablet to
turn off the stop; the indicator is unlit
Selecting a Sound Variation (Voice Palette)
Press the lower part of a tablet
1.
From the main screen, press the lower part of a division tablet.
The “Voice Palette” screen will appear, showing the variation of the selected stop.
ѥѥIf the indicator blinks momentarily when you press the tablet, a variation is already selected for the stop.
ѥѥIf the “Voice Palette” screen is not shown, return to the main screen (press the [Value/Exit Menu] knob a number of times) and perform the procedure from step 1.
2.
Turn the [Value/Exit Menu] knob.
You can choose from four sound variations: VP0 through VP3.
22
Storing a Combination of Stops
About the general memory pistons
The general memory pistons can store the stop, coupler, and tremulant settings. The stored settings are maintained even when the power is
turned off.
There are 10 general memory pistons, 1 through 10, and each piston can store one registration. The combination of general memory pistons 1–10
is stored as a “bank.” For example there are 10 pistons and 20 banks, this means that you can store a total of 200 registrations.
Registrations are a convenient way to store favorite combinations of sounds, or to switch between combinations of sounds while you perform.
About the division memory pistons
While the general memory pistons store a combination of sounds for the entire organ, the division memory pistons store only the combination of
sounds for each division.
The combination of division memory pistons is stored as a “bank.”
Storing or Recalling a Registration
Storing a Registration
1.
2.
Set the stops so that you hear the combination of sounds you want to store.
While holding down the [SET] piston, press one of the general memory pistons or division memory pistons.
• If you press a general memory piston, the state of the stops for all divisions, the couplers, and the tremulant will be stored.
• If you press one of the division memory piston, the state of the stops and the tremulant for the division will be stored at that piston.
Recalling a Registration
1.
Press one of the general memory pistons or division memory pistons.
Resetting the Sound Settings (General Cancel)
1.
Press the general cancel [0] piston.
The illumination for all stops and pistons will turn off.
If you also want to reset the stop variations
Press and hold the general cancel [0] piston for several seconds; the settings will be reset to a state in which no sound is selected, and the variation
settings will also be reset for all tablets, restoring the basic variation (Default Voice Palette).
23
Storing a Combination of Stops
Using Memory Banks
The state of the general memory pistons and the division memory pistons can be stored as a “memory bank.”
M02
M01
Storing the Combination of Memory Pistons as a Memory Bank
1.
Use the memory bank select [M–]/[M+] pistons to select the memory bank number to be used for storage.
2.
While holding the [SET] piston, press one of the general memory pistons or division memory pistons.
NOTE
ѥѥPlease be aware that the information that was previously stored in the memory bank will be overwritten and lost.
Recalling a Registration from a Different Memory Bank
1.
From the main screen, use the memory bank select [M–]/[M+] pistons to select the number of the memory bank that you want to
recall.
MEMO
If you hold down the memory bank select [M–]/[M+] piston, the memory bank number will continue changing consecutively.
NOTE
ѥѥSimply pressing a memory bank select [M–]/[M+] piston will not recall a registration.
2.
Press one of the general memory pistons or division memory pistons.
Recalling Registrations Successively
Simply by pressing the [NEXT] piston, you can successively recall the registrations that are stored at the general memory pistons.
For example, if you will be performing a recital, you can use the memories to store your registrations in the order in which you will be using them, and
then smoothly switch to the next registration while you perform.
Each press recalls the next registration
M01
24
M02
Storing a Combination of Stops
Using Memory Banks with USB Memory
Preparing USB Flash Drive
1.
For preparing the USB Memory, refer to “Formatting USB Flash Drive” (p. 33).
Selecting USB Memory Folder
The capacity of an external memory device is much greater than that of the organ’s internal combination memory. In order to make easy use of this
additional capacity, Rodgers uses the concept of memory folders. Like a file folder, a memory folder is used to store groups of information on the memory
device. Each folder can contain a copy of each console memory bank, plus a copy of the Crescendo sequence, and Full Organ. Folders on a memory
device are labeled A through Z.
This means that a single device can contain up to 26 different copies of all Memory Banks, Crescendo Sequences, and Full Organ.
1.
Connect your USB flash drive to the USB memory connector.
2.
From the main screen, press the [Select/Menu] knob.
3.
Turn the [Select/Menu] knob to select “USB Memory.”
4.
Press the [Select/Menu] knob to access the “USB Memory.”
5.
Turn the [Value/Exit Menu] knob to select a USB Memory folder A-Z.
Storing the Combination of Memory Pistons as a Memory Bank to USB Memory
1.
Use the memory bank select [M–]/[M+] pistons to select the memory bank number to be used for storage.
2.
While holding the [SET] piston, press one of the general memory pistons or division memory pistons.
NOTE
ѥѥPlease be aware that the information that was previously stored in the memory bank will be overwritten and lost.
Recalling a Registration from a Different Memory Bank from USB Memory
1.
From the main screen, use the memory bank select [M–]/[M+] pistons to select the number of the memory bank that you want to
recall.
MEMO
If you hold down the memory bank select [M–]/[M+] piston, the memory bank number will continue changing consecutively.
NOTE
ѥѥSimply pressing a memory bank select [M–]/[M+] piston will not recall a registration.
2.
Press one of the general memory pistons or division memory pistons.
25
Changing the Settings for FULL ORGAN
Setting the Sound to be Played When the [FULL ORGAN] Piston is Pressed
1.
While holding down the [SET] piston, press the [FULL ORGAN] piston.
2.
Press a sound tablet, and select the stop you want to be sounded.
3.
Press the [SET] piston to save your settings.
The sound tablet set for FULL ORGAN will light.
ѥѥYou can’t select a tremulant tablet.
MEMO
If you connect USB Flash Drive, your setting is saved to USB Memory.
Setting Whether Tablet Illumination is On/Off When the [FULL ORGAN] Piston is Pressed
Refer to “Blind [S]” (p. 16).
Changing the Settings for Crescendo
1.
From the main screen, press the [Select/Menu] knob.
2.
Turn the [Select/Menu] knob to select “Crescendo.”
3.
Press the [Select/Menu] knob to access the “Crescendo.”
4.
Turn the [Value/Exit Menu] knob to select Crescendo Step 0–63.
5.
Press a sound tablet, and select the stop you want to be sounded.
6.
Press the [SET] piston to save your settings.
ѥѥYou can’t select a tremulant tablet.
ѥѥYou can’t save your settings at Step 0.
MEMO
You can have two independent Crescendo sequences, a Standard Crescendo and an Alternate Crescendo. Pressing the [ALT CRESC] reversible piston so
that it lights engages the Alternate Crescendo sequence.
MEMO
If you connect USB Flash Drive, your setting is saved to USB Memory.
Changing ORGAN TYPE
Organ type allows you to select “Voice Palettes” that specifies which variation sound will be heard when you turn on a specific tablet.
1.
Press [ORGAN TYPE] piston.
2.
Turn the [Select/Menu] knob to select “Organ Type.”
3.
Menu item
Explanation
American Eclectic
Transparency and clarity of tone, eclectic specification characteristic of modern 20th century American organ builders
English Cathedral
Broad 8’ fundamental tone and smooth dark reeds typical of Willis and Harrison & Harrison organs
French Romantic
Warm 8’ ensemble and bright, fiery reeds characteristic of 19th-century Cavaillé-Coll tonal style
German Baroque
Articulate and bright tonal spectrum in the North German style of 17th-century Arp Schnitger organs
Press [ORGAN TYPE] piston again to return to the main screen.
NOTE
Press and hold the general cancel [0] piston for several seconds, the settings will be reset to “Default Voice Palettes.”
26
Practicing Along with a Preset Song or Performance Data
You can practice by playing along with preset songs (demo songs) that are built into the organ, or with performance data that you’ve recorded from your
own playing.
MEMO
Songs can also be played back in succession. Start from the state where playback is stopped. Then, using the [Select/Menu] knob, select “Play Mode.”
Next, turn the [Value/Exit Menu] knob to change the setting to “CHAIN.”
Setting
Explanation
OFF
Play back only the selected song
CHAIN
Consecutively play back all the songs on the selected media
Selecting and Playing Back a Song
1.
If you want to play back a song from USB flash drive, connect your USB flash drive to the USB memory connector.
2.
From the main screen, press the [STOP] piston to access the “Song Recorder” screen.
3.
Turn the [Select/Menu] knob to select “Source.”
4.
Turn the [Value/Exit Menu] knob to select the media on which the song is stored.
Setting
Explanation
USB
Play back song data from USB flash drive
INTERNAL
Play back song data from internal memory
PRESET
Play back built-in preset song (demo song)
5.
Turn the [Select/Menu] knob to select “Song.”
6.
Turn the [Value/Exit Menu] knob to choose the song that you want to play back.
If a screen like the following appears
If internal memory contains performance data that has not been saved, the following message will appear when you attempt to select a saved song.
• If you want to discard the performance data without saving it, press the [SET] piston.
• If you don’t want to erase the performance data, press the [Value/Exit Menu] knob. Save the performance data as described in “Saving a Recorded
Song” (p. 29).
7.
Press the [PLAY/PAUSE] piston to play back the song data.
• “PU” is shown as the measure number if the song starts on a weak (“pick up”) beat.
• You can pause the playback.
Press the [PLAY/PAUSE] piston. Playback will resume from the same location when you press the [PLAY/PAUSE] piston once again.
8.
To stop playback, press the [STOP] piston.
27
Practicing Along with a Preset Song or Performance Data
Muting a Specific Division During Playback
When playing back a song, you can individually mute (silence) the performances of each division.
1.
From the main screen, press the [STOP] piston to access the “Song Recorder” screen.
2.
Choose the song that you want to play back.
3.
Turn the [Select/Menu] knob to select “Division Mute.”
4.
Press the [Select/Menu] knob to access the “Division Mute” screen.
5.
Turn the [Select/Menu] knob to select the division that you want to mute.
6.
Turn the [Value/Exit Menu] knob to change the setting from “PLAY” to “MUTE.”
7.
Press the [PLAY/PAUSE] piston to play back the song.
You can play along on the muted division(s) while listening to the recorded performance.
ѥѥWhen you reselect the performance data, muting will be cancelled for all divisions.
Playing Back a Specific Division as a Guide Tone
1.
From the main screen, press the [STOP] piston to access the “Song Recorder” screen.
2.
Choose the song that you want to play back.
3.
Turn the [Select/Menu] knob to select “Division Mute.”
4.
Press the [Select/Menu] knob to access the “Division Mute” screen.
5.
Turn the [Select/Menu] knob to select the division that you want to play back as a guide tone.
6.
Turn the [Value/Exit Menu] knob to change the setting from “PLAY” to “GUIDE.”
7.
Turn the [Select/Menu] knob to select the “Guide Volume.”
8.
Turn the [Value/Exit Menu] knob to adjust the volume of the guide tone.
Setting
1–10
9.
Turn the [Select/Menu] knob to select the “Guide Tone.”
10. Turn the [Value/Exit Menu] knob to select the guide tone.
You can choose one of the following nine types of tone for the guide tone.
Setting
Explanation
F: Flute
F16, P16, R16, F8, P8, R8, F4, P4, R4
P: Principal
R: Reed
Number: Footage
11. Press the [PLAY/PAUSE] piston to play back.
ѥѥWhen you reselect the performance data, all divisions will sound using their original tone.
MEMO
These settings will return to the default value when you turn off the power, but you can store the Guide volume and the Guide Tone setting so that it
will be remembered even after the power is turned off.
For details, refer to “Storing Your Settings (Customize)” (p. 21).
28
Recording Your Performances
Recording a Song
1.
From the main screen, press the [STOP] piston to access the “Song Recorder” screen.
MEMO
You can also access the “Song Recorder” screen by Quick Menu.
2.
Press the [REC] piston; the [REC] piston will light.
The [PLAY/PAUSE] piston will blink, and the organ will enter recording-standby mode.
MEMO
If desired, you can sound the metronome while you record.
3.
When you play the keyboard, the [PLAY/PAUSE] piston will light and recording will start automatically.
MEMO
You can also start recording by pressing the [PLAY/PAUSE] piston. In this case, recording will begin after two measures have passed. If you’re using the
metronome, the metronome will sound.
4.
Press the [STOP] piston to stop recording.
The [PLAY/PAUSE] piston’s light will go out.
Play Back the Recorded Song
1.
Press the [STOP] piston to return to the first measure of the song you recorded.
2.
Press the [PLAY/PAUSE] piston to play back the recorded song.
MEMO
Press the [PLAY/PAUSE] piston, you can pause the playback. Playback will resume from the same location when you press the [PLAY/PAUSE] piston
once again.
3.
To stop playback, press the [STOP] piston.
Saving a Recorded Song
The song you recorded will be lost when you switch off the organ’s power. If you want to keep the recorded song, you must save it to USB flash drive or to
the organ’s internal memory.
1.
If you want to save to USB flash drive, connect your USB flash drive to the USB memory connector (p. 26).
2.
From the main screen, press the [STOP] piston to access the “Song Recorder” screen.
3.
Turn the [Select/Menu] knob to select “Save Song.”
4.
Press the [Select/Menu] knob to access the “Save Song” screen.
5.
Turn the [Select/Menu] knob to select “Save to,” and turn the [Value/Exit menu] knob to choose the desired save destination.
6.
Save to
Explanation
INTERNAL
The song will be saved to internal memory.
USB
The song will be saved to USB flash drive. Shown only if USB flash drive is connected to
the USB memory connector.
Turn the [Select/Menu] knob to select “Name,” and press the [Select/MENU] knob to assign a name to the song.
For details on how to assign a name, refer to “If you want to name the data you’re saving” (p. 31).
MEMO
The song you recorded will automatically be given the name “New Song.”
7.
Turn the [Select/Menu] knob to select “No.”, and turn the [Value/Exit menu] knob to choose the save-destination number.
8.
Press the [SET] piston; the data will be saved.
When saving is finished, the name of the newly saved song data will appear.
9.
Press the [Value/Exit Menu] knob twice to return to the main screen.
29
Recording Your Performances
If a screen like the following appears
If the save destination already contains data, the following message will appear.
• Press the [SET] piston if you want to overwrite the data; i.e., replace the previous contents of the song.
The existing data will be erased, and the performance data you recorded will be saved.
• If you decide that you want to keep the performance data that’s currently in the save-destination, press the [Value/Exit Menu] knob.
The Save operation will be cancelled, and you’ll return to the previous screen. Select a different save-destination.
Deleting a Recorded Song
MEMO
You can’t erase a preset song.
1.
If you want to delete a song that’s saved on USB flash drive, connect your USB flash drive to the USB memory connector.
2.
From the main screen, press the [STOP] piston to access the “Song Recorder” screen.
3.
Turn the [Select/Menu] knob to select “Delete Song.”
4.
Press the [Select/Menu] knob to access the “Delete Song” screen.
5.
Turn the [Select/Menu] knob to select “Delete from”, and turn the [Value/Exit Menu] knob to select the appropriate media.
Setting
Explanation
INTERNAL
Delete a song from internal memory.
USB
Delete a song from USB flash drive. Shown only if USB flash drive is connected to the
USB memory connector.
6.
Turn the [Select/Menu] knob to select “No.”, and turn the [Value/Exit Menu] knob to specify the song that you want to delete.
7.
Press the [SET] piston; a confirmation screen will appear.
8.
Press the [SET] piston once again to delete the song.
If you decide to cancel, press the [Value/Exit Menu] knob.
NOTE
ѥѥDo not disconnect the USB flash drive or turn off the power before the deletion has been completed. Otherwise, you risk damaging the USB flash drive or the
organ’s internal memory, rendering it unusable.
9.
30
Press the [Value/Exit Menu] knob three times to return to the main screen.
Recording Your Performances
Copying a Saved Song
MEMO
• You can’t copy a preset song.
• Up to 99 songs can be saved in internal memory, and up to 999 songs can be saved in one USB flash drive unit.
1.
Connect your USB flash drive to the USB memory connector.
2.
From the main screen, press the [STOP] piston to access the “Song Recorder” screen.
3.
Turn the [Select/Menu] knob to select “Copy Song.”
4.
Press the [Select/Menu] knob to access the “Copy Song” screen.
5.
Turn the [Select/Menu] knob to select “Copy from,” and then turn the [Value/Exit Menu] knob to select the media that contains the
data you want to copy.
6.
Setting
Explanation
INTERNAL
Copy song data from the organ’s internal memory to the USB flash drive.
USB
Copy song data from USB flash drive to the internal memory.
Turn the [Select/Menu] knob to select the “Name” field, and turn the [Value/Exit Menu] knob to select the song that you want to
copy.
MEMO
In the “Name” field, choose “Copy All” if you want to copy all of the performance data.
If you choose “Copy All,” select a copy-destination number that will allow all of the data to be copied. For example, if you are copying the 10 songs
saved in internal memory to USB flash drive, choose number 990 or lower as the copy-destination number.
7.
Turn the [Select/Menu] knob toward the right to select the “No.” field, and turn the [Value/Exit Menu] knob to select the desired
copy-destination number.
8.
Press the [SET] piston to execute the copy.
If you decide to cancel, press the [Value/Exit Menu] knob.
NOTE
ѥѥNever disconnect the USB flash drive or turn off the power before the copy has been completed. Otherwise, you risk damaging the USB flash drive or the
organ’s internal memory, rendering it unusable.
9.
When copying is finished, the song name will change to the copy-source song name.
10. Press the [Value/Exit Menu] knob twice to return to the main screen.
If you want to name the data you’re saving
You can assign a name to the performance data, memory banks, and voice setup data.
1.
At the “Name” item, press the [Select/Menu] knob.
2.
Turn the [Select/Menu] knob to move the cursor to left or right, and turn the [Value/Exit Menu] knob to change the character at
the cursor location.
3.
Press the [SET] piston to finalize the name.
You can use the following characters.
(space)
Operation
Explanation
Press [M–] piston
Deletes a character.
Press [M+] piston
Inserts a space.
31
Hymn Player
Selecting Hymn or Prelude
Changing Hymn book
1.
Press the [HYMN PLAYER] piston.
1.
Press [HYMN PLAYER] piston.
2.
Turn the [Select/Menu] knob to move the cursor to Mode.
2.
Turn the [Select/Menu] knob to select “Book”.
3.
Turn the [Value/Exit Menu] knob to select Hymn or Prelude.
3.
Turn the [Value/Exit Menu] knob to select Hymn book.
Selecting Hymn number
1.
Press the [HYMN PLAYER] piston.
2.
Turn the [Select/Menu] knob to move the cursor to Hymn
number.
3.
Turn the [Value/Exit Menu] knob to select Hymn number.
Or while holding the [HYMN PLAYER] or [STOP] piston, press number
with the general memory pistons.
Playing Hymn
1.
Press the [PLAY] piston.
2.
When the introduction has finished, press [PLAY] piston again
and the verse will begin. At the conclusion of each verse
simply press [PLAY] piston again to hear as many additional
verses as desired.
An introduction will play for the selected hymn.
If NO introduction to the hymn is desired, turn the [Select/Menu] knob
to Next, and turn the [Value/Exit Menu] knob to select Verse.
Press [PLAY] piston and the hymn will play the verse only.
Playing Prelude
1.
Press the [HYMN PLAYER] piston.
2.
Turn the [Select/Menu] knob to move the cursor to Mode.
3.
Turn the [Value/Exit Menu] knob to select Prelude.
4.
Press the [PLAY] piston.
Automatically selected Prelude will play continuously.
MEMO
Press the [STOP] piston; the [PLAY/PAUSE] piston will blink, and
Prelude will stop automatically at end of the Prelude. To stop Prelude,
press the [STOP] piston again.
32
This setting will return to the default value when you turn off the
power, but you can store the setting so that it will be remembered even
after the power is turned off. For details, refer to “Storing Your Settings
(Customize)” (p. 21).
Saving and Loading Settings on USB Flash Drive
Formatting USB Flash Drive
Copying a Memory Bank
The process of preparing USB flash drive for use by the organ is called
“Formatting.”
Here’s how a specific bank saved in internal memory or USB flash drive
can be copied to another bank of the organ’s internal memory.
If the USB flash drive is not in the correct format for the organ, it cannot
be used by the organ.
You can also return a specific bank of the organ’s internal memory to the
factory-set state.
format the USB flash drive on the organ.
As an example, we’ll show how to load a specific memory bank from
USB flash drive into the organ’s internal memory.
ѥѥBefore you use USB flash drive for the first time with the organ, you must
ѥѥWhen you format USB flash drive, all songs or settings that have been
stored on that USB flash drive will be lost. Once they’re erased, the songs
cannot be recovered, so be sure to check the contents before you execute
formatting.
1.
Connect your USB flash drive to the USB memory connector.
2.
From the main screen, press the [Select/Menu] knob.
3.
Turn the [Select/Menu] knob to select “Save/Load (USB).”
4.
Press the [Select/Menu] knob to access the “Save/Load (USB)”
screen.
5.
Turn the [Select/Menu] knob to select “Format USB Memory.”
6.
Press the [Select/Menu] knob.
A confirmation screen will appear.
If you decide to cancel the format operation, press the [Value/Exit
Menu] knob.
7.
1.
As a precaution, save the internal memory banks to USB flash
drive. Refer to “Using Memory Banks with USB Memory” (p. 25).
2.
Connect your USB flash drive to the USB memory connector.
3.
From the main screen, press the [Select/Menu] knob.
4.
Turn the [Select/Menu] knob to select “Save/Load (USB).”
5.
Press the [Select/Menu] knob to access the “Save/Load (USB)”
screen.
6.
Turn the [Select/Menu] knob to select “Copy Memory Bank.”
7.
Press the [Select/Menu] knob to access the “Copy Memory
Bank” screen.
8.
Turn the [Select/Menu] knob to select “Copy from,” and turn
the [Value/Exit Menu] knob to change to “USB.”
When doing so, choose a number that indicates (Empty).
Select the “Copy from” setting as appropriate.
Press the [SET] piston to execute formatting.
NOTE
ѥѥNever disconnect the USB flash drive before formatting has been
completed. Always wait until the “Executing” indication is no longer
shown.
8.
Press the [Value/Exit Menu] knob to return to the main
screen.
Deleting a Memory Bank from USB
Flash Drive
9.
Setting
Explanation
FACTORY
Return the specified bank to the factory-set state
INTERNAL
Copy the specified internal bank to another bank
USB
From the memory banks saved on USB flash drive, load only the
specified bank into internal memory
Turn the [Select/Menu] knob to select the “Copy From Bank”
field, and turn the [Value/Exit Menu] knob to select the
memory bank that you want to copy.
10. Turn the [Select/Menu] knob to select the “Copy to INT Bank”
field, and turn the [Value/Exit Menu] knob to select the
desired copy-destination bank number.
1.
Connect your USB flash drive to the USB memory connector.
2.
From the main screen, press the [Select/Menu] knob.
A confirmation screen will appear.
3.
Turn the [Select/Menu] knob to select “Save/Load (USB).”
If you decide to cancel, press the [Value/Exit Menu] knob.
4.
Press the [Select/Menu] knob to access the “Save/Load (USB)”
screen.
5.
Turn the [Select/Menu] knob to select “Delete Memory Bank.”
6.
Press the [Select/Menu] knob to access the “Delete Memory
Bank” screen.
7.
At “Delete Bank” turn the [Value/Exit Menu] knob to select the
sound settings (registration) that you want to delete.
8.
Press the [SET] piston to delete the settings.
11. Press the [SET] piston.
12. Press the [SET] piston; the memory bank will be copied.
A confirmation screen will appear.
If you decide to cancel, press the [Value/Exit Menu] knob.
9.
Press the [SET] piston; the sound settings (registration) will be
deleted.
NOTE
ѥѥNever disconnect the USB flash drive or turn off the power before the
sound settings have been deleted.
33
Saving and Loading Settings on USB Flash Drive
Saving and Loading Voice Setup
A “Voice Setup” contains data that specifies the volume balance of each
sound (stop), its brightness, and various adjustments for parameters.
9.
The organ’s voice setup will switch to the voice setup you loaded.
ѥѥThis setting will return to the default value when you turn off the power, but
you can store the setting so that it will be remembered even after the power
is turned off. For details, refer to “Storing Your Settings (Customize)” (p. 21).
ѥѥUp to 999 sets of voice setups can be saved on one USB flash drive device.
NOTE
Saving to USB Flash Drive
1.
Connect your USB flash drive to the USB memory connector.
2.
From the main screen, press the [Select/Menu] knob.
3.
Turn the [Select/Menu] knob to select “Save/Load (USB).”
4.
Press the [Select/Menu] knob to access the “Save/Load (USB)”
screen.
5.
Turn the [Select/Menu] knob to select “Save Voice Setup.”
6.
Press the [Select/Menu] knob to access the “Save Voice Setup”
screen.
7.
Turn the [Select/Menu] knob to select the “Name” field, and
press the [Select/Menu] knob to assign a name to the voice
setup you want to save.
8.
ѥѥTo prevent malfunction, never turn off the power while the voice setup is
being switched.
Deleting a Voice Setup
1.
If you want to deleting a voice setup from USB flash drive,
connect your USB flash drive to the USB memory connector.
2.
From the main screen, press the [Select/Menu] knob.
3.
Turn the [Select/Menu] knob to select “Save/Load (USB).”
4.
Press the [Select/Menu] knob to access the “Save/Load (USB)”
screen.
5.
Turn the [Select/Menu] knob to select “Delete Voice Setup.”
6.
For details on how to assign a name, refer to”If you want to name the
data you’re saving” (p. 31).
Press the [Select/Menu] knob to access the “Delete Voice
Setup” screen.
7.
Turn the [Select/Menu] knob to select the “No.” field, and turn
the [Value/Exit Menu] knob to choose the desired savedestination number.
Turn the [Select/Menu] knob to select “No.” field, and turn
the [Value/Exit Menu] knob to select the voice setup that you
want to delete.
8.
Press the [SET] piston.
If you don’t want to overwrite an existing voice setup, choose a save
destination that’s indicated as “Empty.”
If you decide to cancel, press the [Value/Exit Menu] knob.
9.
Press the [SET] piston.
The currently used voice setup will be saved to USB flash drive.
NOTE
ѥѥTo prevent malfunction, never disconnect the USB flash drive or turn off
the power while a voice setup is being saved to USB flash drive.
Loading a Voice Setup
1.
If you want to load a voice setup from USB flash drive,
connect your USB flash drive to the USB memory connector.
2.
From the main screen, press the [Select/Menu] knob.
3.
Turn the [Select/Menu] knob to select “Save/Load (USB).”
4.
Press the [Select/Menu] knob to access the “Save/Load (USB)”
screen.
5.
Turn the [Select/Menu] knob to select “Load Voice Setup.”
6.
Press the [Select/Menu] knob to access the “Load Voice Setup”
screen.
7.
Turn the [Value/Exit Menu] knob to select the name of the
voice setup that you want to use.
8.
Press the [SET] piston.
A confirmation screen will appear.
If you decide to cancel, press the [Value/Exit Menu] knob.
34
Press the [SET] piston.
A confirmation screen will appear.
If you decide to cancel, press the [Value/Exit Menu] knob.
9.
Press the [SET] piston; the voice setup will be deleted.
NOTE
ѥѥNever disconnect the USB flash drive or turn off the power until the voice
setup have been deleted.
Backing Up Data/Performing an Initialization
Returning all Settings to the FactorySet State (Factory Reset)
All settings stored in the organ can be reset to their factory-set
condition. This operation is called “Factory Reset.”
NOTE
ѥѥFactory reset will cause all of the recorded songs, the general memory
pistons, division memory pistons, and all settings stored in the organ
to return to their factory settings. Please copy your settings to USB flash
drive before you proceed.
• “Backing Up/Loading Data” (p. 35)
1.
From the main screen, press the [Select/Menu] knob.
2.
Turn the [Select/Menu] knob to select “Utility.”
3.
Press the [Select/Menu] knob to access the “Utility” screen.
4.
Turn the [Select/Menu] knob to select “Factory Reset.”
5.
Press the [Select/Menu] knob.
Confirmation screen will appear.
Backing Up/Loading Data
Here’s how to back up and load data.
1.
Connect your USB flash drive to the USB memory connector.
2.
From the main screen, press the [Select/Menu] knob.
3.
Turn the [Select/Menu] knob to select “Utility.”
4.
Press the [Select/Menu] knob to access the “Utility” screen.
5.
Turn the [Select/Menu] knob to select “Backup/Restore.”
6.
Press the [Select/Menu] knob to access the “Backup/Restore”
screen.
7.
Turn the [Select/Menu] knob to select “Direction,” then turn
the [Value/Exit Menu] knob to select either backup or load.
8.
If you decide to cancel, press the [Value/Exit Menu] knob.
6.
Press the [SET] piston to execute Factory Reset.
NOTE
ѥѥThe Factory Reset will be executed. Do not turn off the power while
Turn the power off, then on again.
Explanation
BACK UP
Selected to back up data.
RESTORE
Selected to load data.
Press the [SET] piston to carry out the data backup or load
procedure.
If you decide to cancel, press the [Value/Exit Menu] knob.
Displaying the Version
Here’s how to check the software version being used.
“Executing” is displayed.
7.
Setting
1.
From the main screen, press the [Select/Menu] knob.
2.
Turn the [Select/Menu] knob to select “Utility.”
3.
Press the [Select/Menu] knob to access the “Utility” screen.
4.
Turn the [Select/Menu] knob to select “Version .”
5.
Press the [Select/Menu] knob to access the “Version ” screen.
35
List of Shortcuts
By using these shortcuts you can directly access a desired screen without going through a menu screen.
To access the screen
Shortcut
Demo screen
Press the [PLAY/PAUSE] piston
Pitch/Tuning screen
Press any key
Operate the expression pedal
Expression Pedal screen
Edit parameter save confirmation screen
Operate the kick switch
While holding in the [SET] piston
Turn the [Master Volume] knob
Room Modeling screen
Turn the [Reverb] knob
Press the bass coupler [BASS] piston
Console screen
Press the melody coupler [MEL I] or [MEL III] piston
Song Recorder screen
Press the [STOP] piston
To access the Transpose
Shortcut
From Main Screen
While holding in the [SET] piston
ѥѥAll shortcut operations must be performed from the main screen.
36
Press the general cancel piston [0]
Audio screen
Turn the [Value/Exit Menu] knob
For EU Countries
This product complies with the requirements of EMCD 2004/108/EC and LVD 2006/95/EC.
FEDERAL COMMUNICATIONS COMMISSION
RADIO FREQUENCY INTERFERENCE STATEMENT
For the USA
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment requires shielded interface cables in order to meet FCC class B limit.
Any unauthorized changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
For Canada
NOTICE
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
AVIS
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.
WARNING
For C.A. US (Proposition 65)
This product contains chemicals known to cause cancer, birth defects and other reproductive harm, including lead.
For China
For EU Countries
Rodgers Instruments Corporation
1300 NE 25th Ave., Hillsboro, OR 97124
503-648-4181
PN 1905406 RevC
© 2010, Rodgers Instruments Corporation
Where applicable, if you qualify as a “consumer” under the Magnuson-Moss Warranty Act, then you shall be entitled to any implied warranties allowed by law for the period of
the Limited Warranty as set forth above. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. EXCEPT AS
STATED ABOVE, THE FOREGOING WARRANTIES ARE IN LIEU OF ALL OTHER CONDITIONS OR WARRANTIES, EXPRESS, IMPLIED OR STATUTORY INCLUDING
WITHOUT LIMITATION, AN IMPLIED CONDITION OR WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AND OF ANY OTHER
WARRANTY OBLIGATION ON THE PART OF RODGERS INSTRUMENTS CORPORATION. RODGERS INSTRUMENTS CORPORATION DOES NOT ASSUME OR AUTHORIZE ASSUMPTION OF LIABILITY FOR IT OR ANY OTHER WARRANTY, EITHER EXPRESS OR IMPLIED. THIS LIMITED WARRANTY GIVES U.S. PURCHASERS
SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
IN NO EVENT SHALL RODGERS INSTRUMENTS CORPORATION BE LIABLE FOR ANY DIRECT, INCIDENTAL, COLLATERAL, EXEMPLARY, PUNITIVE, CONSEQUENTIAL OR SPECIAL DAMAGES OR LOSSES ARISING OUT OF YOUR PURCHASE OF THIS PRODUCT AND/OR OUT OF THIS WARRANTY, INCLUDING WITHOUT LIMITATION, LOSS OF USE, PROFITS, GOODWILL OR SAVINGS OR LOSS OF DATA, MUSIC, ELECTRONIC FILES, OR PROGRAMS THAT MAY HAVE BEEN
STORED BY A USER OF THIS PRODUCT EVEN IF RODGERS INSTRUMENTS CORPORATION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR
CLAIMS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL, PUNITIVE OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
Conditions, Limitations and Restrictions of this Warranty
The Warranty for this product does not apply to the following:
A. Any product that was not purchased directly from an Authorized Rodgers Dealer;
B. Any defects or damage that occurred as a result of abuse or misuse, neglect or abnormal service or handling;
C. Any defects or damage that was caused by installation, repairs or service, including the use of improper parts, provided or attempted by anyone who is not authorized by
Rodgers Instruments Corporation;
D. Any defects or damage that may have been caused, either directly or indirectly, by the use of another product;
E. Any defects or damage that occurred because the product has been altered or modified in any way;
F. Any defects or damages which may have been caused by an Act of God, such as fire, flood, earthquake, lightning, rain, wind, hurricane, etc., which are beyond the control
of Rodgers Instruments Corporation;
G. Any defects or damages which may have occurred by ordinary wear and tear;
H. Any and all accessories, peripheral products or other equipment.
I. Any defects or damage that resulted from commercial use of the product.
Parts Warranty
Rodgers Instruments Corporation warrants only to the original Purchaser of this product that all the parts contained in this product will be free from defects in materials and/or
workmanship for a period of ten (10) years from the date of purchase. Any repaired or replaced parts in your product will be warranted for the unexpired portion of this parts warranty. All transportation and freight charges shall be paid by Purchaser. Rodgers Instruments Corporation is not responsible for any labor for this product.
LIMITED WARRANTY
Rodgers Instruments Corporation Musical Instrument, Speaker and Amplifier
Online warranty registration available at www.rodgersinstruments.com/warranty
1905444
Jan. 1, 2012
Copyright 2012 Rodgers Instruments Corporation. All rights reserved.
1PS