MATERIAL SAFETY DATA SHEET

MATERIAL SAFETY DATA SHEET
(Essentially Similar to Form OSHA-174 / 29 CFR 1910-1200)
PRODUCT NAME
FORMULA
HMIS RATING
InstantFOAM™ alcohol hand sanitizer
AFS6510FCi
HEALTH = 0 FIRE = 3 REACTIVITY = 0
(Scale 0-4, where 4 = severe hazard)
SECTION I – MANUFACTURER INFORMATION
MANUFACTURED
BY DEB FOR
PHONE NUMBER
DEB SBS, Inc.
1100 Highway 27 South
Stanley, NC 28164
704-263-4240
EMERGENCY CONTACT
PREPARED BY
REVISION DATE
Chemtrec
800-424-9300 (24 hour)
Sandra N. Porter
July 2, 2009
REASON FOR CHANGE Fire=3 (HMIS)
SECTION II – INGREDIENTS
This product is manufactured and labeled in compliance with the Federal Food, Drug, and Cosmetic Act, and is exempt from the
labeling requirements of the OSHA Hazard Communication Standard. All product ingredients are listed below.
ACTIVE INGREDIENT
Ethyl Alcohol
CAS NUMBER
64-17-5
INACTIVE INGREDIENTS
Water
n-Propanol
Coco-Glucoside
Glyceryl Oleate
PEG-7 Glyceryl Cocoate
PEG-200 Hydrogenated Glyceryl Palmate
Dihydroxypropyl PEG-5 Linoleaminium Chloride
Behentrimonium Chloride
Bis-PEG-12 Dimethicone
7732-18-5
71-23-8
141464-42-8
68424-61-3
68201-46-7
67784-88-7
168677-75-6
17301-53-0
102783-01-7
FORMULA, %
72 (by volume)
Data marked with asterisk (*) in section III below refer to the properties of Ethyl Alcohol
SECTION III - PHYSICAL/CHEMICAL CHARACTERISTICS
BOILING POINT
VAPOR PRESSURE (mmHg)
VAPOR DENSITY (Air = 1)
SOLUBILITY IN WATER
APPEARANCE & ODOR
SPECIFIC GRAVITY (H20 = 1)
NA
ND
MELTING POINT
ND
EVAPORATION RATE (Butyl Acetate = 1)
Complete
pH
Clear to slightly opaque liquid with an alcohol odor
0.80
NA
1.4 *
NA
SECTION IV - FIRE AND EXPLOSION HAZARD DATA
FLASH POINT (Method Used)
FLAMMABLE LIMITS
EXTINGUISHING MEDIA
SPECIAL FIRE FIGHTING PROCEDURES
UNUSUAL FIRE AND EXPLOSION HAZARDS
72°F (ASTM D-1310 open cup)
LEL: ND
UEL: ND
Dry chemical, carbon dioxide, water spray (fog) or alcohol foam
Blanket fire with extinguishing medium.
Undetermined
MATERIAL SAFETY DATA SHEET – InstantFOAM™ alcohol hand sanitizer, page 2
SECTION V - REACTIVITY DATA
STABILITY
Unstable
Stable
Conditions to Avoid:
Heat or ignition sources
X
INCOMPATIBILITY
Oxidizing agents; may react with aluminum at high temperatures
HAZARDOUS DECOMPOSITION
OR BY-PRODUCTS
Ammonia, nitrous oxides, and hydrogen chloride are produced upon combustion.
HAZARDOUS POLYMERIZATION
May Occur
Will not Occur
Conditions to Avoid:
None known
X
SECTION VI – HEALTH HAZARD DATA
ROUTE(S) OF ENTRY
Inhalation, Ingestion only by accidental or intentional misuse
HEALTH HAZARDS
Skin:
Eyes:
Ingestion:
Inhalation:
Excessive exposure may cause irritation or dryness.
May cause temporary irritation.
May result in vomiting.
Vapors may cause drowsiness.
EMERGENCY AND FIRST AID PROCEDURES
Skin:
Rinse affected area with water. Consult with a physician if irritation persists.
Eyes:
Immediately flush eyes with clean water for at least 15 minutes or until irritation subsides. Consult with a
physician if pain or irritation persists.
Ingestion:
Do not induce vomiting. Consult with a physician immediately.
Inhalation:
Remove from exposure. Consult with a physician if condition persists.
SECTION VII - PRECAUTIONS FOR SAFE HANDLING AND USE
IN CASE OF RELEASE OR SPILL
WASTE DISPOSAL METHOD
PRECAUTIONS FOR HANDLING
AND STORAGE
Apply absorbent material and place in covered containers for disposal.
Dispose in accordance with state, local and federal regulations.
Keep out of reach of children and other persons who may misuse the product.
Avoid contact with excessive heat, ignition sources, and incompatible materials.
Store in cool, well-ventilated area. Do not store in aluminum containers.
SECTION VIII - CONTROL MEASURES
SPECIAL RESPIRATORY PROTECTION
SPECIAL SKIN PROTECTION
SPECIAL EYE PROTECTION
None required
None required
Avoid eye contact.
While the information and recommendations set forth herein are believed to be accurate as of the date hereof, DEB SBS, Inc. makes
no warranty with respect thereto and disclaims all liability from reliance thereon, and responsibility for improper application or misuse
of product in any manner whatsoever. Final determination of suitability of any material is the sole responsibility of the user.