12000E IP Broadband Loop Carrier
Installation Instructions
Document Number IPD1-A2-GZ40-00
February 2005
Contents
Software and Firmware License Agreement ...................................................... 1
Introduction ........................................................................................................ 3
Unpacking and Inspecting the Equipment ......................................................... 3
Installation Options ............................................................................................ 4
Installing Your Management Module ................................................................. 6
Installing Your Interface Module(s) .................................................................... 9
Establishing Your Uplink Connections ............................................................... 14
Connecting Your Subscriber Lines .................................................................... 15
Configuration and Management ........................................................................ 18
Product Documentation Online .......................................................................... 18
Fan Module ........................................................................................................ 19
Specifications ..................................................................................................... 20
Important Safety Instructions ............................................................................. 20
Warranty, Sales, Service, and Training Information ........................................... 22
Software and Firmware License Agreement
ONCE YOU HAVE READ THIS LICENSE AGREEMENT AND AGREE TO ITS
TERMS, YOU MAY USE THE SOFTWARE AND/OR FIRMWARE INCORPORATED
INTO THE PARADYNE PRODUCT. BY USING THE PARADYNE PRODUCT YOU
SHOW YOUR ACCEPTANCE OF THE TERMS OF THIS LICENSE AGREEMENT.
IN THE EVENT THAT YOU DO NOT AGREE WITH ANY OF THE TERMS OF THIS
LICENSE AGREEMENT, PROMPTLY RETURN THE UNUSED PRODUCT IN ITS
ORIGINAL PACKAGING AND YOUR SALES RECEIPT OR INVOICE TO THE
LOCATION WHERE YOU OBTAINED THE PARADYNE PRODUCT OR THE
LOCATION FROM WHICH IT WAS SHIPPED TO YOU, AS APPLICABLE, AND YOU
WILL RECEIVE A REFUND OR CREDIT FOR THE PARADYNE PRODUCT
PURCHASED BY YOU.
The terms and conditions of this License Agreement (the “Agreement”) will apply
to the software and/or firmware (individually or collectively the “Software”)
incorporated into the Paradyne product (the “Product”) purchased by you and any
derivatives obtained from the Software, including any copy of either. If you have
IPD1-A2-GZ40-00
February 2005
1
executed a separate written agreement covering the Software supplied to you
under this purchase, such separate written agreement shall govern.
Paradyne Corporation (“Paradyne”) grants to you, and you (“Licensee”) agree to
accept a personal, non-transferable, non-exclusive, right (without the right to
sublicense) to use the Software, solely as it is intended and solely as incorporated
in the Product purchased from Paradyne or its authorized distributor or reseller
under the following terms and conditions:
1. Ownership: The Software is the sole property of Paradyne and/or its licensors.
The Licensee acquires no title, right or interest in the Software other than the
license granted under this Agreement.
2. Licensee shall not use the Software in any country other than the country in
which the Product was rightfully purchased except upon prior written notice to
Paradyne and an agreement in writing to additional terms.
3. The Licensee shall not reverse engineer, decompile or disassemble the
Software in whole or in part.
4. The Licensee shall not copy the Software except for a single archival copy.
5. Except for the Product warranty contained in the manual, the Software is
provided “AS IS” and in its present state and condition and Paradyne makes
no other warranty whatsoever with respect to the Product purchased by you.
THIS AGREEMENT EXPRESSLY EXCLUDES ALL OTHER WARRANTIES,
WHETHER EXPRESS OR IMPLIED, OR ORAL OR WRITTEN, INCLUDING
WITHOUT LIMITATION:
a. Any warranty that the Software is error-free, will operate uninterrupted in
your operating environment, or is compatible with any equipment or
software configurations; and
b. ANY AND ALL IMPLIED WARRANTIES, INCLUDING WITHOUT
LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS
FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT.
Some states or other jurisdictions do not allow the exclusion of implied
warranties on limitations on how long an implied warranty lasts, so the above
limitations may not apply to you. This warranty gives you specific legal rights,
and you may also have other rights which vary from one state or jurisdiction to
another.
6. In no event will Paradyne be liable to Licensee for any consequential,
incidental, punitive or special damages, including any lost profits or lost
savings, loss of business information or business interruption or other
pecuniary loss arising out of the use or inability to use the Software, whether
based on contract, tort, warranty or other legal or equitable grounds, even if
Paradyne has been advised of the possibility of such damages, or for any
claim by any third party.
7. The rights granted under this Agreement may not be assigned, sublicensed or
otherwise transferred by the Licensee to any third party without the prior
written consent of Paradyne.
8. This Agreement and the license granted under this Agreement shall be
terminated in the event of breach by the Licensee of any provisions of this
Agreement.
2
February 2005
IPD1-A2-GZ40-00
9. Upon such termination, the Licensee shall refrain from any further use of the
Software and destroy the original and all copies of the Software in the
possession of Licensee together with all documentation and related materials.
10. This Agreement shall be governed by the laws of the State of Florida, without
regard to its provisions concerning conflicts of laws.
Introduction
Paradyne’s 12000E IP Broadband Loop Carrier (BLC) provides a high capacity
and native IP Ethernet foundation for a variety of feature-rich multi-service access
multiplexer modules.
The 12000E BLC is engineered for efficient, high-speed IP data transport in a
compact, fully fault-tolerant chassis. It features a high capacity backplane
delivering up to 48 Gbps throughput and providing a non-blocking architecture for
even the highest bandwidth broadband access technologies, such as ADSL2+.
The 12000E BLC supports single or dual redundant uplink, management, and
switching modules. In redundant mode, both modules can be connected to the
dual backplanes with redundant modular backhaul/uplink ports to support 10/100
Ethernet, GigE (Copper or fiber), T1/E1, and dual bonded T1/E1 uplink modules.
For flexibility of installation the 12000E has removable mounting brackets that can
be placed in increments of 1.45” up to 9.28” from the front of the chassis, allowing
for multiple installation options in either 19" or 23" equipment racks.
Unpacking and Inspecting the Equipment
HANDLING PRECAUTIONS FOR
! STATIC-SENSITIVE DEVICES
This product is designed to protect sensitive components from damage
due to electrostatic discharge (ESD) during normal operation. When
performing installation procedures, however, take proper static control
precautions to prevent damage to equipment. If you are not sure of the
proper static control precautions, contact your nearest sales or service
representative.
The following components should be included in the shipping container:
IPD1-A2-GZ40-00
„
1 – 12000E with 1 fan module and 12 blank plates
„
4 – Rubber Bumper Screws
„
2 – Rack Mount Brackets (either 19" or 23", as ordered)
„
10 – #6 Phillips Bracket Screws
„
8 – #10 Phillips Rack Screws
„
8 – #12 Phillips Rack Screws
February 2005
3
If there is visible damage, do not attempt to connect the device. Contact your sales
representative.
Installation Options
The 12000E BLC is designed for installation in a Restricted Access area where
admittance is limited to trained and authorized service personel. It may be
installed on a tabletop or in a rack.
Installation on a Tabletop
Insert the four provided rubber bumper screws into the mounting holes at the
bottom of the 12000E chassis for surface grip and airflow. Position and secure all
connecting cables such that they will not become a tripping hazard or pull loose
from the chassis. Ensure that the air supply vents around the top and bottom
edges of the chassis are not blocked.
(%277209,(:
58%%(5%803(5
6&5(:
6LGH
)URQW
4
7RS
5HDU
February 2005
IPD1-A2-GZ40-00
Installing in a Rack
Procedure
1. Using a Phillips screwdriver, attach the two provided rack mount brackets to
the sides of the 12000E with eight of the ten provided bracket screws. There
are seven position options for the rack brackets; position them as best suited
to the space available for your chassis on the rack being utilized.
5$&.02817
%5$&.(7
(6,'(9,(:
)URQW
IPD1-A2-GZ40-00
5HDU
February 2005
5
2. Mount the chassis onto the rack and secure the rack mount brackets to the
sides of the rack using one of the two provided sets of eight rack screws
(whichever size fits the rack being utilized).
()52179,(:
3. Check the rack for stability, ensuring that installation of the 12000E has not
caused the rack to become top-heavy. Position and secure all connecting
cables such that they will not become a tripping hazard or pull loose from the
chassis.
Installing Your Management Module
A management module provides the functional control for the 12000E BLC; the
BLC cannot function without one. There are several different models available for
purchase. Refer to www.paradyne.com for further information, or contact your
sales representative.
Installing a Management Module
An uplink module provides the upstream network connection for the12000E BLC;
a management module cannot function without one. Depending on the
management module model that you plan to install in your 12000E, you will need
either a Media Interface Module (MIM) or an Uplink Interface Module (UIM). Only
one uplink module is required for operational purposes, however two uplink
modules may be installed, one in each port of the management module, if
redundancy is desired. Refer to your management module and/or uplink module
installation instructions for further information.
CAUTION:
If a blank plate is removed from a management module uplink port, it must be
replaced with an uplink module. DO NOT OPERATE A 12000E BLC WITH A
MANAGEMENT MODULE THAT HAS AN OPEN UPLINK PORT.
6
February 2005
IPD1-A2-GZ40-00
Procedure
1. Select a slot for installation. The 12000E is a fourteen slot chassis: slots 1–12
are reserved for interface modules and slots U1–U2 are reserved for
management modules. Although the 12000E is shipped with Port U1 open,
your management module can be installed in either Port U1 or Port U2. Only
one management module is required for operational purposes. However, two
management modules may be installed if redundancy is desired: one in Slot
U1 and one in Slot U2.
CAUTION:
If the blank plate is removed from Slot U2, it must be replaced with a
management module. DO NOT OPERATE YOUR 12000E WITH AN
EMPTY MODULE SLOT.
0DQDJHPHQW0RGXOH6ORWV
IPD1-A2-GZ40-00
February 2005
7
2. With the management module printed circuit board (PCB) facing right and the
management module model name upright, align the upper and lower edges of
the PCB with the slot module guides.
0$1$*(0(17
02'8/(
6ORW0RGXOH*XLGHV
3. Slide the management module firmly into the chassis. Tighten the fastening
screws on the management module faceplate.
)DVWHQLQJ6FUHZV
8
February 2005
IPD1-A2-GZ40-00
Installing Your Interface Module(s)
Interface modules provide the subscriber connections for an 12000E; up to twelve
interface modules may be installed in the 12000E (slots 1–12). There are a variety
of models available for purchase; contact your sales representative for further
information or visit www.paradyne.com for a list of available products. Any
combination of interface module models may be installed in an 12000E as long as
they are supported by the model type and version number of your management
module; refer to the Release Notes for your particular management module model
for compatibility information.
Procedure
1. Select a slot for installation. Although the 12000E is factory shipped with Slot 1
open, interface modules may be installed in any slot, 1–12.
CAUTION:
If a blank plate is removed from slot 2–12, it must be replaced with an
interface module. DO NOT OPERATE YOUR 12000E WITH AN EMPTY
MODULE SLOT.
2. With the interface module PCB facing right and the interface module model
name upright, align the upper and lower edges of the PCB with the slot
module guides.
,17(5)$&(
02'8/(
6ORW0RGXOH*XLGHV
IPD1-A2-GZ40-00
February 2005
9
3. Slide the interface module firmly into the chassis. Tighten the fastening screws
on the interface module faceplate.
)DVWHQLQJ6FUHZV
10
February 2005
IPD1-A2-GZ40-00
Powering Up Your 12000E
CAUTION:
Turn your DC power source(s) OFF until you have completed connection of
the 12000E as outlined in the following sections.
Do not operate the 12000E without a ground connection.
Procedure
1. Connect a ground wire to the 12000E: Line up the 2-hole terminal lug of your
ground wire with the two holes on the small, unpainted section on the back of
your chassis. Secure the terminal lug to the chassis with two #10-32 screws.
(5($59,(:
*URXQG&RQQHFWLRQIRU+ROH7HUPLQDO/XJ
*5281'&211(&7,21&/26(83
2. Connect the ground wire to a frame ground. Ground wire connection can vary
from location to location though typically all equipment in a Central Office is
grounded to a common copper bus.
IPD1-A2-GZ40-00
February 2005
11
3. Select a terminal block. Either terminal block on the back of the 12000E may
be used to power the chassis; only one terminal block is required for
operational purposes. The two terminal blocks on the 12000E are independent
feeds. Chassis power is supplied by only one terminal block at a time; the
second supply is a backup. Likewise, the two terminal blocks do not
load-share. Each terminal block must be supplied with adequate amperage to
run the chassis independently.
CAUTION:
Two identical terminal blocks are provided on the 12000E chassis to allow
for redundant 48V DC power sources. Each power source to be connected
with the 12000E must be equipped with a disconnect device such as an
On/Off switch, or, an appropriately rated circuit breaker must be installed
on each power circuit to be used. Hazardous voltages will not be removed
from the 12000E until all power sources have been either turned off or
disconnected from the chassis.
'&7HUPLQDO%ORFN
12
February 2005
'&7HUPLQDO%ORFN
IPD1-A2-GZ40-00
4. Using a Phillips screwdriver, remove the left-hand screw from the chosen
terminal block (labeled "+" on the chassis). Slide the ring terminal of your
positive power lead around the shaft of the screw and insert the screw into the
same "+" terminal from which it was removed.
3RVLWLYH7HUPLQDO
326,7,9(32:(5/($'
'&32:(57(50,1$/
5LQJ7HUPLQDO
5. Remove the right-hand screw (labeled "–") from the same terminal block. Slide
the ring terminal of your NEGATIVE lead around the shaft of the screw and
re-insert the screw into the same "–" terminal from which it was removed.
1HJDWLYH±7HUPLQDO
'&32:(57(50,1$/
1(*$7,9(32:(5/($'
5LQJ7HUPLQDO
CAUTION:
Observe proper polarity.
6. Connect both power leads to a fuse panel. The negative (–) lead connects to a
"Batt" (Battery) terminal and the positive (+) lead connects to a "Return"
terminal on your DC power supply.
IPD1-A2-GZ40-00
February 2005
13
7. Verify the connection. Turn your power source(s) on. The PWR (power) LED
on the interface module and management module faceplates will illuminate
solid green to indicate the modules are receiving power.
,17(5)$&(
02'8/(
0$1$*(0(1702'8/(
3RZHU/('
3RZHU/('
Establishing Your Uplink Connections
No configuration is necessary for Uplink Interface Modules (UIMs) or Media
Interface Modules (MIMs) installed on the management module(s) in your 12000E
to operate at default settings. However, if you wish to run your uplink connections
at settings other than the UIM or MIM defaults, configure the UIM or MIM prior to
connection.
For further connection and configuration information, refer to the installation
instructions of your particular UIM or MIM.
Uplink Module
14
February 2005
IPD1-A2-GZ40-00
Connecting Your Subscriber Lines
No configuration is necessary for the interface module(s) installed in your 12000E
to operate at default settings. However, if you wish to run your subscriber
connections at settings other than the defaults, configure the interface module(s)
prior to connection. Refer to the installation instructions for your particular interface
module(s).
The 12000E chassis supports ADSL, IDSL, SDSL and T1/E1 technologies.
Ensure that the subscriber lines you are connecting correspond with the
technology of the interface module(s) installed in your 12000E.
Procedure
1. Identify the Appropriate RJ21 Connector(s). Subscriber lines must be
connected according to the 12000E slot in which the corresponding interface
module was installed. Interface module slots 1–12 run from left to right when
you are facing the front of the chassis; the corresponding RJ21 ports are
directly behind each slot on the back of the chassis (1–12, right to left, when
you are facing the back of the chassis). Each interface module slot on the
12000E has two corresponding RJ21 connectors located on the back of the
chassis. The bottom row of RJ21 connectors (A) provides the connection for
interface module ports 1–24 (on most models) and the top row of RJ21
connectors (B) provides the interface module connection for ports 25–48 (on
applicable models). For the TIM1500-24 interface module, the A connector
provides connection for ports 1–12 and the B connector provides the
connection for ports 13–24.
(5($59,(:
%&RQQHFWRUV±
6XEVFULEHUFRQQHFWLRQV
IRULQWHUIDFHPRGXOH
SRUWV±RQ
DSSOLFDEOHPRGHOV
$&RQQHFWRUV±
6XEVFULEHUFRQQHFWLRQV
IRULQWHUIDFHPRGXOH
SRUWV±RQPRVW
PRGHOV
IPD1-A2-GZ40-00
February 2005
15
2. Detach the hook-and-loop fastener strap from the female RJ21 connector port:
lift the hook-and-loop fastener tab on the left and pull the strap open towards
the right, leaving it looped under the right side of the connector frame.
)(0$/(5-&211(&725$
)25,17(5)$&(02'8/(6/27
3. Slide the male RJ21 connector of your interface cable underneath the
hook-and-loop fastener, from the bottom, and press it firmly into the female
RJ21 connector port on the chassis.
0$/(5-&211(&7252)
<285,17(5)$&(&$%/(
4. Pull the hook-and-loop fastener strap to the right, making sure that it is snug
against the connector, then pull the strap back towards the left, such that the
hook-and-loop fastener layers stick to one another across the top of the
connector. Tuck the tab at the end of the strap down to the left of the connector
frame so that it is out of the way of other connections and then screw the top of
the RJ21 cable connector into the jack screw at the top of the RJ21 connector
frame on the chassis. Note: If you are using a 120 or 180 degree cable, both
the top and the bottom of the cable connector should be screwed to the RJ21
connector frame on the chassis.
16
February 2005
IPD1-A2-GZ40-00
5. Verify the connection(s). The LK (Link) LED for each port being connected
with a remote modem will illuminate solid or flashing green (depending on the
interface module model) to indicate a connection has been established. Link
up time between interface modules and remote modems can vary from one to
five minutes depending on the quality, gauge and distance of the copper cable
pair(s) being used. Refer to individual interface module user guides for specific
information such as connector pinouts, parameter configurations and distance
capabilities.
IPD1-A2-GZ40-00
February 2005
17
Configuration and Management
Although no configuration is necessary to run subscriber lines at the default
settings, all 12000E parameter settings are software selectable via Command Line
Interface (CLI), Simple Network Management Protocol (SNMP), or the Network
Management System (NMS), depending upon the capabilities of the management
module model installed in your chassis. Once the management module has been
initialized, interface modules may be configured as desired via whichever
system(s) your management module is capable of running.
Refer to the following documentation for further information:
Document
Contents
„
Management module
installation instructions
(model-specific)
Uplink module installation
instructions
„
(model-specific)
„
Interface module user
guides
(model-specific)
„
CLI Management User
Guide
NMS Management User
Guide
„
module installation
port pinouts
parameter defaults
parameter configuration options
management system capabilities
module installation
port pinouts
parameter defaults
parameter configuration options
module installation
distance and bandwidth capabilities
port pinouts
parameter defaults
parameter configuration options
management module initialization instructions
command user guide
command definitions
configuration options common to all management
module models
configuration options common to all interface module
models
management module initialization instructions
screen by screen user guide
parameter definitions
configuration options common to all management
module models
configuration options common to all interface module
models
Product Documentation Online
Complete documentation for Paradyne products is available at
www.paradyne.com. Select Support → Technical Manuals.
To order a paper copy of a Paradyne document, or to speak with a sales
representative, please call 1-727-530-2000.
18
February 2005
IPD1-A2-GZ40-00
Fan Module
The 12000E fan module is installed horizontally above the interface module slots.
It comes pre-installed and should not be removed unless it is being replaced. Fan
functionality is indicated by a FAN LED on the management module (all models):
no illumination or solid green illumination indicates all fans are currently
functioning, solid amber illumination indicates one or more of the four fans are no
longer functioning.
()52179,(:
)DQ0RGXOH
0$1$*(0(17
02'8/(
Fan
LED
CAUTION:
Do not operate the 12000E without a fan module or with a fan module that is
not functioning properly.
IPD1-A2-GZ40-00
February 2005
19
Specifications
Table 1. Specifications
Specification
Criteria
Environment
Operating Temperature:
–40°F to 149°F (–40°C to 65°C)
Storage Temperature:
–40°F to 158°F (–40°C to 70°C)
Humidity:
5% to 95%, non-condensing
Altitude:
–200ft to 16,500ft (-60m to 5,000m)
Physical
+LJK[:LGH['HHS
FP[FP[FP
OEVNJ
Power
–48V DC
30 Amps maximum
Although actual power draw depends upon chassis
configuration, a fully loaded chassis averages around 15
Amps.
Regulatory Compliance
NEBS:
GR-63-CORE; GR-1089-CORE
EMC:
FCC Part 15; CSA/C108.8; EN55022; EN55024
Safety:
UL 60950-1 1st Edition, UL Marking; CSA 22.2
No. 60950-1-03; EN60950-1:2001; CE Marking
Telecom:
ACTA968 (Part 68); ICCS-03; TBR12; TBR13
! Important Safety Instructions
1. Read and follow all warning notices and instructions marked on the product or
included in the manual.
2. Do not attempt to service this product yourself, as opening or removing covers
may expose you to dangerous high voltage points or other risks. Refer all
servicing to qualified service personnel.
3. This product is to be installed only in a Restricted Access Location (dedicated
equipment rooms, equipment closets or the like) in accordance with articles
110-16, 110-17 and 110-18 of the National Electrical Code, ANSI/NFPA 70.
4. This product is to be connected to a 48 VDC SELV supply source that is
electrically isolated from the AC source.
20
February 2005
IPD1-A2-GZ40-00
5. The positive terminal of the 48 VDC source is to be reliably connected to
earth. Connect a green/yellow earthing (grounding) wire to the protective
earthing (grounding) lug connector, identified by the protective earth symbol
on the chassis.
6. A readily accessible disconnect device as part of the building installation shall
be incorporated in fixed wiring. The disconnect device (a 48 VDC, 20A, single
pole circuit breaker or switch) must be included in the ungrounded supply
conductor. Over current protection must be included with a 20A, 48 VDC fuse
or circuit breaker in the ungrounded conductor. Use minimum 18 AWG fixed
power source wires with strain retention.
7. Do not allow anything to rest on the power cord and do not locate the product
where persons will walk on the power cord.
8. Slots and openings in the cabinet are provided for ventilation. To ensure
reliable operation of the product and to protect it from overheating, these slots
and openings must not be blocked or covered.
9. General purpose cables are described for use with this product. Special
cables, which may be required by the regulatory inspection authority for the
installation site, are the responsibility of the customer. To reduce the risk of
fire, use a UL Listed or CSA Certified, minimum No. 26 AWG (0.128 mm2)
telecommunication cable, or comparable cables certified for use in the country
of installation.
10. A rare phenomenon can create a voltage potential between the earth grounds
of two or more buildings. If products installed in separate buildings are
interconnected, the voltage potential may cause a hazardous condition.
Consult a qualified electrical consultant to determine whether or not this
phenomenon exists and, if necessary, implement corrective action prior to
interconnecting the products.
11. In addition, if the equipment is to be used with telecommunications circuits,
take the following precautions:
— Never install telephone wiring during a lightning storm.
— Never install telephone jacks in wet locations unless the jack is specifically
designed for wet locations.
— Never touch uninsulated telephone wires or terminals unless the
telephone line has been disconnected at the network interface.
— Use caution when installing or modifying telephone lines.
— Avoid using a telephone (other than a cordless type) during an electrical
storm. There may be a remote risk of electric shock from lightning.
— Do not use the telephone to report a gas leak in the vicinity of the leak.
12. The equipment is intended for installation in a max. 65° C ambient
temperature, in an environment that is free of dust and dirt.
13. When installed in the final configuration, the product must comply with the
applicable Safety Standards and regulatory requirements of the country in
which it is installed. If necessary, consult with the appropriate regulatory
agencies and inspection authorities to ensure compliance.
IPD1-A2-GZ40-00
February 2005
21
! UNITED STATES – EMI NOTICE:
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
The authority to operate this equipment is conditioned by the
requirements that no modifications will be made to the equipment
unless the changes or modifications are expressly approved by
Paradyne Corporation.
! CANADA – EMI NOTICE:
This Class A digital apparatus meets all requirements of the Canadian
interference-causing equipment regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du
règlement sur le matérial brouilleur du Canada.
Warranty, Sales, Service, and Training Information
Contact your local sales representative, service representative, or distributor
directly for any help needed. For additional information concerning warranty, sales,
service, repair, installation, documentation, training, distributor locations, or
Paradyne worldwide office locations, use one of the following methods:
„
Internet: Visit the Paradyne World Wide Web site at www.paradyne.com.
(Be sure to register your warranty at www.paradyne.com/warranty.)
„
Telephone: Call our automated system to receive current information by fax or
to speak with a company representative.
— Within the U.S.A., call 1-800-870-2221
— Outside the U.S.A., call 1-727-530-2340
$.
*IPD1-A2-GZ40-00*
Copyright © 2005 Paradyne Corporation. Printed in U.S.A.
22
February 2005
IPD1-A2-GZ40-00