LCR-8000G Series 10MHz / 5MHz / 1MHz PRECISION LCR METER

10MHz / 5MHz / 1MHz PRECISION LCR METER
LCR-8000G Series
FEATURES
Wide Test Frequency 20Hz~10/5/1MHz
0.1% Basic Accuracy & 6 Digits
Measurement Resolution
Large LCD Display with Intuitive User
Interface
Full Measuring Functions with DUT V/I
Monitor
PASS/FAIL Function ( abs , % ,
with Judgment Alarm
The Smarter Way to Characterize Components
The LCR-8000G Series LCR meter, with test frequency up to 10MHz, provides accuracy, versatility and high
resolution for a wide range of component measurements, even including DC resistance measurement and
Voltage/Current monitoring. The Multi-Step function allows on-screen programming of customized
measurement sequence with Pass/Fail indication. Each program includes 30 test steps and each test step can be
set with selected parameters and test limits. Under Multi-Step operation, a tedious work routine can be done
step by step automatically just at a press of a button. With Graph Mode, LCR-8110G, LCR-8105G and LCR-8101G
display the component impedance response either over a wide range of test frequency sweep or over a wide
range of test voltage sweep in a graph chart. This gives an analysis result of either impedance vs. frequency or
impedance vs. applied voltage all at a glance. GPIB and RS-232C interfaces are available as standard for
instrument control and test result display on the PC. The rich features of LCR-8000G Series easily make your
measurement tasks done at a very competitive price.
Wide Frequency Range With Friendly
Intuitive User Interface
The LCR-8000G Series is designed to perform precision
impedance measurements over a wide frequency range
of 20Hz ~ 10MHz for LCR-8110G, 20Hz ~ 5MHz for
LCR-8105G and 20Hz ~1MHz for LCR-8101G. The
instrument is capable of measuring 11 different
parameters with 0.1% basic accuracy, which meets the
precision measurement requirements of components
and modules used in the RF circuits. The large LCD
display with single-layer operation menu of LCR-8000G
Series provides users with ultimate convenience to
plug and play without much learning time.
Average 1 ~ 256 Times
DC Resistance Measurement
Multi Step Mode
Graph Mode
Standard RS-232C / GPIB Interface
Graph Mode
The graph function shows the component
characteristics in visual manner. Either voltage sweep
or frequency sweep can be selected for horizontal
scale. Just select the parameter, and set the start/stop
C.
voltage or the start/stop frequency of the sweep, LCR
-8000G will run through the sequence of
measurements and show the results on a graph.
This graphical parameter measurement performs the
characteristic verification of components and
materials over the response to the changes in AC test
frequency or AC test voltage without the need of
complex programming of an external controller. When
the graph gets out of the vertical range, the LCR8000G Series can automatically adjust the scale to
get full test information. On the graph the marker
operation is available for detailed observation.
Multi Step Mode
Pass/fail Function With Judgment Alarm
The Multi-Step mode is capable of running a series of
measurements of a component at a number of userdefined steps in sequence automatically. Total 64
programs can be saved into the non-volatile memory,
and each program contains up to 30 test steps. The
parameter and Hi/Lo limits can be set respectively for
each test step. After a program being properly edited,
the instrument can run through all the measurement
steps either at a press of the button under the Manual
Trigger selection, or automatically run the program by
detecting the connection of a DUT under the Auto
Trigger selection. When all the test steps are
completed, the screen shows the measurement
reading of the parameter being selected for each step
with Pass, HI, or LO measurement result.
In the Pass/Fail test, primary parameter measurement
result is compared with user-defined limits and the
pass or fail result is then displayed. Three methods,
including absolute limit, percentage and delta limit,
are available for Hi(high) and Lo(low) limit setting
based on the nominal test value. The Pass/Fail test
checks whether the parameter measurement result
sits within the limits, then display "PASS" for within
the limits, or "LO" for lower than the low limit, or
"HI" For higher than the high limit. A scale and bar
for displaying measurement result is shown at the
center of the screen to give a graphical identification,
which greatly reduces operator's load in a long time
inspection work. This scale and bar also facilitate the
adjustment of the variable components. Either Pass
or Fail result can be set with a buzzer alarm, which
makes component or material sorting easy with
sound identification.
LCR-8000G Series
)
C.
APPLICATIONS
Education Lab and Training Institution
Research & Design
Quality Assurance Verification
Made to Measure
Since 1975
SPECIFICATIONS
TEST FREQUENCY
20Hz ~ 10MHz/5MHz/1MHz, 5 Digits, 0.005%
INPUT IMPEDANCE
100
BASIC ACCURACY
(*)
0.1% (R, Z, X, G, Y, B, L, C)
TEST SPEED
DC
MAX: 30mS
FAST: 60mS
MEDIUM: 120mS
SLOW: 900mS
AC (>2kHz)
MAX: 75mS
FAST: 150mS
MEDIUM: 450mS
SLOW: 600mS
TEST SIGNAL LEVELS
Test Frequency
3MHz
> 3MHz
Test Signal Level (rms)
10mV ~ 2V
10mV ~ 1V
Step
1mV/10mV
1mV/10mV
Accuracy
2% 5mV
2% 5mV
Max. 20mA
SHORT CIRCUIT CURRENT
MEASUREMENT RANGES
Mode
R, Z, X, Rdc
G, Y, B
L
C
D
Q
Measure Range
0.1m ~ 100M
10nS ~ 1000S
0.1nH ~ 100kH
0.01pF ~ 1F
0.00001 ~ 9.9999
0.1 ~ 9999.9
-180 ~ +180
MEASUREMENT PARAMETERS
Impedance (Z), Phase Angle ( ), Inductance (L), Capacitance (C), AC Resistance (Rac), Quality Factor (Q),
Dissipation Factor (D), Admittance (Y), Conductance (G), Reactance (X), Susceptance (B), DC Resistance (Rdc)
SERIES OR PARALLEL EQUIVALENT CIRCUIT
C + R, C + D, C + Q, L + R, L + Q, L + D
SERIES EQUIVALENT CIRCUIT ONLY
X + R, X + D, X + Q
PARALLEL EQUIVALENT CIRCUIT ONLY
C + G, B + G, B + D, B + Q, B + R, L + G
POLAR FORM
Z + Phase Angle, Y + Phase Angle
AVERAGE
1 ~ 256 times
LCD DISPLAY
320 x 240 DOT-MATRIX
INTERFACE
RS-232C, GPIB
POWER SOURCE
AC 115V (+10%/-25%), AC 230V (+15% / -14%)(Selectable), 50/60Hz
DIMENSIONS & WEIGHT
330(W) x 170(H) x 340(D)mm, Approx. 5kg
(*):Basic accuracy varies with the speed, frequency, AC signal level and the impedance of DUT.
ORDERING INFORMATION
LCR-8110G
LCR-8105G
LCR-8101G
Specifications subject to change without notice.
CR-8000GGD2DH
STANDARD ACCESSORIES
User manual x 1
Power cord x 1
Test lead LCR-12 x 1
10 MHz Precision LCR Meter
5 MHz Precision LCR Meter
1 MHz Precision LCR Meter
OPTIONAL ACCESSORIES SELECTION GUIDE
Accessory Model
LCR-05
LCR-06A
LCR-07
LCR-08
LCR-09
LCR-12
LCR-13
GTL-232
GRA-404
Note "
Brief Description
LCR-8110G
LCR-8105G
LCR-8101G
Test Fixture for axial & radial lead components
Test Lead with Kelvin clip (4 wire type)
Test Lead with Alligator clip (2 wire type)
Test Fixture (Tweezers) for SMD/Chip components
Test Fixture for SMD/Chip components
Test Lead with Kelvin clip (4 wire type)
Test Fixture for SMD/Chip components
RS-232C Cable
Rack Adapter Panel (19", 4U)
" means the accessories work with a frequency limitation (under 1MHz)
LCR-05
LCR-06A
LCR-07
LCR-08
LCR-09
Global Headquarters
U.S.A. Subsidiary
GOOD WILL INSTRUMENT CO., LTD.
INSTEK AMERICA CORP.
No. 7-1, Jhongsing Road, Tucheng City, Taipei County 236, Taiwan
T +886-2-2268-0389 F +886-2-2268-0639
E-mail: marketing@goodwill.com.tw
3661 Walnut Avenue Chino, CA 91710, U.S.A.
T +1-909-5918358 F +1-909-5912280
E-mail: sales@instekamerica.com
China Subsidiary
Japan Subsidiary
GOOD WILL INSTRUMENT (SUHZOU) CO., LTD.
INSTEK JAPAN CORPORATION
NO. 69, Lushan Road, Snd, Suzhou Jiangsu 215011 China
T +86-512-6661-7177 F +86-512-6661-7277
E-mail: marketing@instek.com.cn
4F, Prosper Bldg, 1-3-3 Iwamoto-Cho Chiyoda-Ku,
Tokyo 101-0032 Japan
T +81-3-5823-5656 F +81-3-5823-5655
E-mail: info@instek.co.jp
Malaysia Subsidiary
Korea Subsidiary
GOOD WILL INSTRUMENT (M) SDN. BHD.
GOOD WILL INSTRUMENT KOREA CO., LTD.
27, Persiaran Mahsuri 1/1, Sunway Tunas,
11900 Bayan Lepas, Penang, Malaysia
T +604-6309988 F +604-6309989
E-mail: sales@goodwill.com.my
Room No.805, Ace Hightech-City B/D 1Dong,
Mullae-Dong 3Ga 55-20, Yeongduengpo-Gu, Seoul, Korea
T +82 2 3439 2205 F +82 2 3439 2207
E-mail : gwinstek@gwinstek.co.kr
LCR-13
LCR-12
Made to Measure
Since 1975
www.gwinstek.com
Simply Reliable
Our low TCO helps you control costs
with reliable products and services.