Micro Hypnotic General Introduction
Unpacking: Thank you for purchasing the Micro Hypnotic by Ameri-
can DJ®. Every Micro Hypnotic has been thoroughly tested and has
been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the
carton appears to be damaged, carefully inspect your fixture for any
damage and be sure all equipment necessary to operate the unit has
arrived intact. In the event damage has been found or parts are missing, please contact our toll free customer support number for further
instructions. Please do not return this unit to your dealer without contacting customer support first.
Introduction: The Micro Hypnotic is a unique mini laser that proj-
ects red and green “web type” patterns. These laser patterns may be
projected on a wall, ceiling, or dance floor. The Micro Hypnotic is a
stand alone fixture with 2 operating modes; sound active mode and
auto mode. The Micro Hypnotic’s compact, light weight case design
make it ideal for mobile entertainers, bands, night clubs and bar. For
best results use fog or special effects smoke to enhance the beams
projections.
Customer Support: American DJ® provides a toll free customer sup-
port line, to provide set up help and to answer any question should
you encounter problems during your set up or initial operation. You
may also visit us on the web at www.americandj.com for any comments or suggestions. For service related issue please contact American DJ®. Service Hours are Monday through Friday 8:00 a.m. to 4:30
p.m. Pacific Standard Time.
Voice:
(800) 322-6337
Fax: (323) 582-2941
E-mail: support@americandj.com
To purchase parts online visit http://parts.americandj.com
Warning! To prevent or reduce the risk of electrical shock or fire, do
User Instructions
Rev. 5/11
not expose this unit to rain or moisture.
Caution! There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures warranty. In the unlikely event your unit may require service please contact
American DJ customer support.
PLEASE recycle the shipping carton whenever possible.
©American
DJ® - www.americandj.com - Micro Hypnotic Instruction Manual Page 2
Micro Hypnotic General Instructions
Please carefully read and understand the instructions in this manual
thoroughly before attempting to operate this unit. These instructions
contain important safety information regarding the use and maintenance of this unit. Please keep this manual with the unit, for future
reference.
CAUTION IMPORTANT! When installing this projector, make sure
that it is mounted in a manner that prevents the audience from
looking directly into the beam, and the beam from striking the
audience.
Micro Hypnotic •
•
•
•
•
Features
30mW (532nm) Green Laser
80mW (650nm) Red Laser
2 Operating Modes - Sound Active Mode & Auto Mode
RF Wireless Remote Control (Included)
Dual Hanging Bracket
Micro Hypnotic
Warranty Registration
The Micro Hypnotic carries a 90 day limited warranty. Please fill out
the enclosed warranty card to validate your purchase. All returned
service items whether under warranty or not, must be freight prepaid and accompany a return authorization (R.A.) number. If the unit
is under warranty you must provide a copy of your proof of purchase
invoice. Please contact American DJ® customer support for a R.A.
number.
©American
DJ® - www.americandj.com - Micro Hypnotic Instruction Manual Page 3
Micro Hypnotic !
Safety Precautions
DANGER
VISIBLE LASER RADIATION
-AVOID DIRECT EYE EXPOSURE
LASER DIODE
WAVELENGTH : 635~650 nm
Max Output : <4.9mW
Class IIIa Laser Product
!
• To reduce the risk of electrical shock or fire, do not expose this unit
rain or moisture.
•Do not spill water or other liquids into or on to your unit.
•Do not attempt to remove or break off the ground prong from the
electrical cord. This prong is used to reduce the risk of electrical shock and fire in case of an internal short. Do not attempt to operate this unit if the power cord has been frayed or broken.
•Disconnect from main power before making any type of connection.
• Do not remove the cover under any conditions. There are no user serviceable parts inside.
•Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6” (15cm) between this device and a wall.
•Do not attempt to operate this unit, if it becomes damaged.
•This unit is intended for indoor use only, use of this product outdoors voids all warranties.
•During long periods of non-use, disconnect the unit’s main power.
•Always mount this unit in safe and stable matter.
•Power cords should be routed so they are not likely to be walked on, pinched by items placed upon or against them.
• Cleaning -The fixture should be cleaned only as recommended by the manufacturer. See page 10 for cleaning details.
•Heat -The appliance should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat.
•The fixture should be serviced by qualified service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen, or liquid has been spilled into the unit.
C. The unit has been exposed to rain or water.
D. The unit does not appear to operate normally or exhibits a
marked change in performance.
©American
DJ® - www.americandj.com - Micro Hypnotic Instruction Manual Page 4
Micro Hypnotic
Laser Warnings and Safety
NON-INTERLOCKED HOUSING WARNING
The Micro Hypnotic contains high power laser devices internally. Do
not open the laser housing, due to the potential exposure to unsafe
levels of laser radiation. The laser power levels, if the unit is opened,
can cause instant blindness, skin burns and fires.
STOP AND READ ALL LASER SAFETY DATA
OPERATION INSTRUCTIONS AND LASER SAFETY
Micro Hypnotic
Laser Warnings and Safety
After setting up, and before public use, test laser to ensure proper
function. Do not use if any defect is detected. Do not use if laser
emits only one or two laser beams rather than dozens/hundreds, as
this could indicate damage to the diffraction grating optic, and could
allow emission of higher laser levels above Class 3R.
Do not point lasers at people or animals. Never look into the laser
aperture or laser beams.
The light source emitted from this product can potentially cause eye
injury if not set up and used properly. The light source emitted from a
laser is very different from any other light sources with which you may
be aware of. Laser light is thousands of times more concentrated
than any light from any other kind of light source. This concentration
of light can cause instant eye injuries, primarily by burning the retina
(the back of your eyeball contatining cells that are sensitive to light).
Even if you cannot feel “heat” from a laser beam, it can still potentially injure or blind you or your audience. Even very small amounts
of laser beam light are potentially hazardous even at long distances.
Laser eye injuries can be sustained faster than you can blink.
Do not point lasers in areas in which people can potentially get
exposed, such as uncontrolled balconies, etc.
Do not think that because this laser splits the laser beam into hundreds of beams and that the laser beam is scanned out in high
speed, that an individual laser beam is safe for eye exposure. This
laser uses dozens of milliwatts of laser power (Class 3B levels internally) before it splits into multiple beams (Class 3R levels). Many of
the individual beams are potentially hazardous to the eyes.
Do not use the laser if the housing is damaged, the housing is open,
or if the optics appear damaged in any way.
Do not that because the laser light is moving, it is safe. This is not
true. Nor, do the laser beams always move. Since eye injuries can
occur instantly, it is critical to prevent even the smallest possibility of
any direct eye exposure. In the laser safety regulation, it is not legal
to aim Class 3R lasers in areas which people can get exposed. This
is true even if it is aimed below people’s faces, such as on a dance
floor.
Do not operate the laser without first reading and understanding
all safety and technical data in this manual.
Always set up and install all laser effects so that all laser light is at
least 3 meters (9.8 feet) above the floor on which people can stand.
©American
DJ® - www.americandj.com - Micro Hypnotic Instruction Manual Page 5
Do not point lasers at highly reflective surfaces, such as windows,
mirrors and shiny metal. Even laser reflections can be hazardous.
Never point a laser at aircraft, this is a federal offense.
Never point un-terminated laser beams into the sky.
Do not expose the output optic (aperture) to cleaning chemicals.
Do not use laser if the laser appears to be emitting only one or two
beams.
Never open the laser housing. The high laser power levels inside of
the protective housing can start fires, burn skin and will cause instant
eye injury.
Never leave this device running unattended.
The operation of a class 3R laser show is only allowed if the show
is controlled by a skilled and well- trained operator, familiar with the
data included in this manual.
The legal requirements for using laser entertainment products vary
from country to country. The user is responsible for the legal requirements at the location/country of use.
Always use proper lighting safety cables when hanging lights and
effects overhead.
©American
DJ® - www.americandj.com - Micro Hypnotic Instruction Manual Page 6
Micro Hypnotic Laser Warning Labels
Micro Hypnotic
Operation
LASER RADIATION
IS EMITTED FROM
THIS APERTURE
20mm
CAUTION IMPORTANT! When installing this projector, make sure
that it is mounted in a manner that prevents the audience from
looking directly into the beam, and the beam from striking the
audience.
AVOID EXPOSURE
40mm
LASER RADIATION AVOID
DIRECT EYE EXPOSURE
Maximum output <5 mW
Wavelength: 650, 532nm
Class IIIa laser product
30 mm
41 mm
This device complies with 21 CFR chapter I,
Subchapter J, or CFR 1040.10 and 1040.11
40mm
17mm
American DJ Supply,Inc.
6122 S.Eastern Ave.
Los Angeles. CA 90040 USA
Manufactured:
Specification stickers
Operating Modes:
• Sound Active mode There are two sound active modes to choose from; slow movement
and fast movement. In either of the these modes the fixture will react
to sound, chasing through the built-in programs.
• Auto Play This function run automatically run through all of units patterns.
Sound Active Mode: This mode allows the unit to run to the beat of
the music.
1. Press the Auto/Sound button. You are in slow sound active mode if the red LED on the front of the unit flashes to the beat of the music. Your are in fast sound active mode if the red LED continuously flashes rapidly.
Auto Play Mode: This mode allows the unit to run Auto Play mode.
1. Press the Auto/Sound button till the red LED on the front of the unit continuously flashes slowly. You are now in Auto Play.
2. Use the speed knob underneath the button to control the speed of the program.
Remote Control: Use the included remote to control various func12mm
40mm
CAUTI ON - CLASS 3R
LASER RADIATION WHEN OPEN
AVOID DIRECT EYE EXPOSURE
tions. Please see below for button control.
Note: This remote control code has been set for this laser, so that
the laser can be controlled out of the box. If this code happens to get
erased the remote will not work with the unit. Please see the next page
to reset the code and link the laser to the remote again.
A Button - Use this button to switch between Auto Play and Sound
Active.
B Button - Use this button to Blackout the unit.
C Button - Use this button to select colors. Either red, green, or red &
green.
©American
DJ® - www.americandj.com - Micro Hypnotic Instruction Manual Page 7
D Button - Use this button to select your desired rotation.
©American
DJ® - www.americandj.com - Micro Hypnotic Instruction Manual Page 8
Micro Hypnotic Laser Remote Reset
Follow these simple instructions to reset your remote code.
2 1
Erase Remote Code:
Using a small pointy utensil, carefully press and hold the white
button (2), while doing this the indicator light (1) will glow for about 5
seconds then turn off. Once the indicator light turns off release the
button (2).
Activating and Linking Remote:
This action will set the code to link the laser to your remote. You can
link more then one laser to a remote.
Using a small pointy untensil, carefully press the white button (2)
and then press any button on the remote control. After pressing the
button on the remote control the indicator light (1) will flash 4 times.
Try to control the unit with the remote. If the unit can be controlled,
setting the code was successful. If it does not control the unit, try
agin.
©American
DJ® - www.americandj.com - Micro Hypnotic Instruction Manual Page 9
Micro Hypnotic Cleaning
Fixture Cleaning: Due to fog residue, smoke, and dust cleaning
the internal and external lenses should be carried out periodically to
optimize light output.
1. Use normal glass cleaner and a soft cloth to wipe down the out-
side casing.
2. Clean the external optics with a microfiber cloth every 20 days.
3. Always be sure to dry all parts completely before plugging the unit back in.
Cleaning frequency depends on the environment in which the fixture
operates (I.e. smoke, fog residue, dust, dew). In heavy use we recommend cleaning on a monthly basis. Periodic cleaning will ensure longevity, and crisp beam output.
Micro Hypnotic Trouble Shooting
Trouble Shooting: Listed below are a few common problems that
you may encounter, with solutions.
No laser output from the unit;
1.Be sure you have connected your unit into a standard wall outlet.
2. Be sure that the unit is not in blackout mode.
3.In cold temperature situations it might take the laser a little longer to produce output. It can take up to 3-5 minutes for the laser to produce a beam. This is due to the laser diode which is very sen-
sitive.
Unit does not respond to sound;
1. Low frequencies (bass) should cause the unit to react to sound.
Tapping on the microphone, quiet or high pitched sounds may
not activate the unit.
©American
DJ® - www.americandj.com - Micro Hypnotic Instruction Manual Page 10
Micro Hypnotic Warranty
MANUFACTURER’S LIMITED WARRANTY
A. American DJ, Inc. hereby warrants, to the original purchaser, American DJ and American
Audio products to be free of manufacturing defects in material and workmanship for a prescribed
period from the date of purchase (see specific warranty period on reverse). This warranty shall be
valid only if the product is purchased within the United States of America, including possessions
and territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable evidence, at the time service is sought.
B.
For warranty service you must obtain a Return Authorization number (RA#) before
sending back the product. Contact American DJ, Inc. Service Department at 800-322-6337. Send
the product only to the American DJ, Inc. factory. All shipping charges must be pre-paid. If the
requested repairs or service (including parts replacement) are within the terms of this warranty,
American DJ, Inc. will pay return shipping charges only to a designated point within the United
States. If the entire instrument is sent, it must be shipped in it’s original package. No accessories
should be shipped with the product. If any accessories are shipped with the product, American DJ,
Inc. shall have no liability whatsoever for loss of or damage to any such accessories, nor for the
safe return thereof.
C. This warranty is void if the serial number has been altered or removed; if the product is
modified in any manner which American DJ, Inc. concludes, after inspection, affects the reliability
of the product; if the product has been repaired or serviced by anyone other than the American DJ,
Inc. factory unless prior written authorization was issued to purchaser by American DJ, Inc.; if the
product is damaged because not properly maintained as set forth in the instruction manual.
D.
This is not a service contract, and this warranty does not include maintenance, cleaning
or periodic check-up. During the period specified above, American DJ, Inc. will replace defective parts at its expense with new or refurbished parts, and will absorb all expenses for warranty
service and repair labor by reason of defects in material or workmanship. The sole responsibility
of American DJ, Inc. under this warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole discretion of American DJ. All products covered by this
warranty were manufactured after January 1, 1990, and bear identifying marks to that effect.
E.
American DJ, Inc. reserves the right to make changes in design and/or improvements
upon its products without any obligation to include these changes in any products theretofore
manufactured. No warranty, whether expressed or implied, is given or made with respect to any
accessory supplied with products described above. Except to the extent prohibited by applicable
law, all implied warranties made by American DJ, Inc. in connection with this product, including
warranties of merchantability or fitness, are limited in duration to the warranty period set forth
above. And no warranties, whether expressed or implied, including warranties of merchantability
or fitness, shall apply to this product after said period has expired. The consumer’s and/or Dealer’s
sole remedy shall be such repair or replacement as is expressly provided above; and under no
circumstances shall American DJ, Inc. be liable for any loss or damage, direct or consequential,
arising out of the use of, or inability to use, this product. This warranty is the only written warranty applicable to American DJ and American Audio Products and supersedes all prior warranties and written descriptions of warranty terms and
conditions heretofore published.
MANUFACTURER’S LIMITED WARRANTY PERIODS:
• All American Audio Products = 1-year (365 day) Limited Warranty (except V-Plus Series Amplifiers)
• All American Audio V-Plus Series Amplifiers = 3-year (1095 day) Limited Warranty
• American DJ Lighting and American DJ Branded Products = 1-year (365 day) Limited Warranty
(Such as: Special Effect Lighting, Intelligent Lighting, UV lighting, Strobes, Fog Machines, Bubble
Machines, Mirror Balls, Par Cans, Trussing, Lighting Stands etc. excluding Laser Products, lamps,
and Star Tec Series)
• American DJ Laser Products and Star Tec Products = 90-Day Limited Warranty
• American DJ L.E.D. Products = 2-year (730 day) Limited Warranty (excluding motors which have
a 1-year (365 day Limited Warranty)
©American DJ® - www.americandj.com - Micro Hypnotic Instruction Manual Page 11
Micro Hypnotic Specifications
Model: Micro Hypnotic
Voltage: 12V DC 100~240V, 50/60Hz
Power Consumption:
9W
Lasers: 30mW Green Diode
80mW Red Diode
Dimensions: 6”(L) x 4.75”(W) x 2.5”(H)
149mm x 110mm x 60mm
Colors:
Red & Green
Weight:
2 Lbs. / .8 kgs.
Duty Cycle:None
Sound Active:Yes
Working Position:
Any Safe, Secure Position
Warranty: 90 Days
Auto Sensing Voltage: This fixture contains a automatic voltage switch, which will auto sense the voltage when it is plugged
into the power source.
Please Note: Specifications and improvements in the design of
this unit and this manual are subject to change without any prior
written notice.
American DJ®
American DJ World Headquarters:
6122 S. Eastern Ave. Los Angeles, CA 90040 USA
Tel: 323-582-2650 / Fax: 323-725-6100
Web: www.americandj.com / E-mail: info@americandj.com
American DJ Europe
Junostraat 2
6468 EW Kerkrade
Netherlands
service@adjgroup.eu / www.americandj.eu
Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99