Digi 20 Series One Circuit Electronic

Digi 20 Series
One Circuit Electronic
24 Hour or 7 Day Time Switches
SURFACE MOUNTING—Digi 20A
Remove dust cover, loosen two screws on opposite corners.
Remove the housing that surrounds the time switch and the
terminal cover away from the base. Remove timer module by
pulling straight out.
Digi 20E
(flush mounting)
Digi 20A
(surface mounting)
C
FILE: E83486
APPLICATION
Time based control of lighting, ventilating, heating, cooling
or other electrical loads in commercial and industrial applications. The Digi 20 time switches are programmable for 24hour or 7-day schedules.
The Digi 20A is intended for either surface or rail mounting.
The control is completely enclosed in a plastic housing and
includes a terminal cover and sub-base for installation and
hard wiring.
The Digi 20E is intended for flush (panel) mounting.
All units are supplied with a clear plastic dust cover. They
are also available with an enclosure for stand-alone applications. (GM and GMX models)
TECHNICAL DATA
Output–1 SPDT relay with dry contacts
Switch Rating: 16A/277VAC resistive
1000W tungsten @ 240VAC; 500W @ 120VAC
1/2 hp @ 120VAC; 1 hp @ 240VAC
100 hour capacitor back-up of memory and display
Supply voltages: Separate Models – 24VAC/DC, 120VAC,
208/240VAC, all 50/60Hz (refer to product label)
Shortest switch time–1 minute
Ambient Temperature Range –20°F to 140°F (–28°C to 60°C)
VA required: 120V & 240V models: 4VA
24V model: 2VA @ 24VAC, 1VA @ 24VDC
Screw terminal connections (Digi 20A)
1/4” quick connects (Digi 20E)
Accuracy ± 4 minutes per year
Installation
To the installer:
1. Read operating instructions carefully.
2. Check the input and output ratings marked on the unit to
make sure this product is suitable for your power supply
and application.
3. Disconnect power supply prior to installation to prevent
electrical shock.
4. Wire in accordance with National and Local electrical code
requirements.
Place screws through 3 mounting holes in base and screw
to back panel or wall.
Wire in accordance with instructions. Replace terminal cover
and push timer firmly onto base. Now replace housing and
secure with screws.
NOTE: The Digi 20A is also suitable for DIN rail mounting.
Break out housing part on each side that fits over rail.
PANEL MOUNTING—Digi 20E
Cut a square hole 2-5/8” x 2-5/8” (66mm x 66mm) in the front
of the panel. Insert the time switch through the opening. With
a screwdriver, press down and turn outer screws (A) until
flanges are in position to fasten the unit in front panel, then
release. Insert plugs into holes (B).
A
B
B
A
Use 1/4” quick connects and make connections in accordance with the wiring diagram shown and applicable code
requirements.
WIRING
1. Disconnect the power.
2. Wire input to timer,
, with the
proper voltage marked on the
unit. Wiring to incorrect voltage
will void the warranty.
3. Connect wiring according to the
wiring diagram. The terminals on
the Digi 20A sub-base will accommodate 10 to 24 AWG wire.
Terminal Connections
TIME
SWITCH
M
COM
1
2
3
NO
4
NC
5
LOAD
POWER
TIMER INTERNAL WIRING
FIELD WIRING
■ KEYPAD DESCRIPTION
■ SELECTING AM/PM OR MILITARY TIME
Setting the Time/Automatic Run Mode
Prog. Program Mode
Res.* Reset: Clears all programs and time
Select ON or OFF in Prog. Mode, Manual Override in Run Mode
±1h* Manual Daylight Change Key
h Setting the Hour (12:– – AM)
m Setting the Minute (12:01 AM)
Day Set Day(s) for time and programs
*Recessed keys; use a pen point to press
■ LCD DISPLAY ELEMENTS
The LCD incorporates a number of different elements to display
various data and information.
After pressing reset, the display may
show AM (right). The numbered day
symbols will be flashing on and off.
If the display does not show AM, it is
in military time mode (24:00 hr.) To
change to AM/PM mode, press and hold
the h key and press the ±1h key once.
AM will appear in display.
If display is in AM mode and military
mode is desired, press and hold the h key, press the ±1h key once.
■ SETTING THE TIME
NOTE: If the h and m keys are held down longer than 2 seconds,
the numbers will advance rapidly.
Press and hold the
key during the following:
(If Daylight Savings Time is in effect, press ±1h first)
1. Press h to advance to the current hour
(while holding down the
key)
Days of the Week ➠
Daylight Time Symbol ➠
AM and PM Symbol ➠
➠
➠
➠
➠
Run Mode Symbol
ON/OFF Symbol
2. Press m to advance to the current minute
(while holding down the
key)
Time of Day or
Switching Time
Manual Override ON
OFF Symbol
Continuous OFF Symbol
ON Symbol
Continuous ON Symbol
■ PROGRAMS
The Digi 20 will accept up to 20 programs
A program consists of:
1. An ON or OFF command
2. Time of day (Hour and Minute)
3. Single day or multiple days
A program is required for each ON event, and a program is
required for each OFF event.
NOTE: MULTIPLE ON OR OFF EVENTS MAY BE PROGRAMMED.
For example, Program 1 may turn the office air conditioning ON at 8AM
Mon.-Fri. Program 2 may turn the air conditioning OFF at 5PM Mon.-Fri.
If someone is working late, they may press the override key to
turn on the air conditioning. If they forget to press the override key
again when they leave, the air conditioning will stay on all night (or
all weekend).
To prevent this from occurring, additional OFF times may be
programmed.
• Program 3 can turn the air conditioning OFF at 6PM.
• Program 4 can turn the air conditioning OFF at 7PM.
• Program 5 can turn the air conditioning OFF at 8PM., etc.
3. Press Day repeatedly to advance to current day (while holding
down the
key)
NOTE: If the days are flashing, it indicates the day of the week was
not set when setting the time. The timer cannot be programmed unless
the day of the week is entered.
■ MANUAL DAYLIGHT TIME CHANGEOVER
Each year, in the Spring, press ±1h to advance the time an hour. In
the Fall, press ±1h to set back an hour.
■ PROGRAMMING 24 HOUR OR 7 DAY SCHEDULES
It is helpful to write out the program schedules
before beginning. See last page.
IMPORTANT: THE CURRENT TIME OF DAY AND DAY OF
WEEK MUST BE SET PRIOR TO PROGRAMMING. SEE “SETTING THE TIME”
!
Example
Program 1: ON at 7:00AM Monday thru Saturday
Program 2: OFF at 5:00PM Monday thru Friday
Program 3: OFF at 7:00PM Saturday
Three programs need to be entered.
Press Prog. key only once. Display shows:
IMPORTANT: BEFORE PROCEEDING WITH SETTING THE
TIME AND PROGRAMMING THE UNIT, PRESS THE RESET
KEY TO CLEAR ALL DATA FROM THE MEMORY.
!
Program 1 (ON at 7:00AM Monday thru Saturday)
Press
key once
Press h key
Press m key once
Press Day key once
Press Prog. key to enter
ON symbol
appears
to 07AM
to 00
1 2 3 4 5 6 is displayed
Program 2 (OFF at 5:00PM Monday thru Friday)
Press
key twice
Press h key
Press m key once
Press Day key two times
Press Prog. key to enter
■ CHANGING A PROGRAM
OFF symbol
appears
to 05PM
to 00
1 2 3 4 5 is displayed
■ DELETING A PROGRAM
Program 3 (OFF at 7:00PM Saturday)
Press
key twice
OFF symbol
appears
Press h key
to 07PM
Press m key once
to 00
Press Day key 9 times
until only 6 is displayed
Press Prog. key to enter
Press
key to enter Run Mode
IMPORTANT: IF AN “ON” TIME WAS PROGRAMMED THAT IS EARLIER IN THE DAY THAN THE CURRENT TIME, PRESS
ONCE TO
TURN THE TIMER “ON”. (IT DOES NOT “LOOK BACK” TO DETERMINE
IF IT SHOULD BE ON OR OFF AFTER PROGRAMMING)
!
NOTE: If 24 hour time control (same schedule every day of the
week) is desired, ignore Day key.
If a ON or OFF symbol is not entered, the ON symbol will flash, and
program will not be accepted.
■ DAY KEY SELECTIONS
Press Day Key
0 times
1 time
2 times
3 times
4 times
5 times
6 times
7 times
8 times
9 times
10 times
Display Shows
1 2 3 4 5 6 7
1 2 3 4 5 6
1 2 3 4 5
6 7
1
2
3
4
5
6
7
Select the program to be changed with the Prog. key. A new set of
days may be selected with the Day key just as in initial programming.
Hour and minute can be changed with the h and m keys.
Press Prog. or
key to store the new program.
Days
Every Day
Mon.–Sat.
Mon.–Fri.
Sat. & Sun.
Monday
Tuesday
Wednesday
Thursday
Friday
Saturday
Sunday
■ REVIEWING PROGRAMS
To review the programs at any time, press Prog. key. Programs will
appear in the order they were entered with repeated presses of the
Prog. key. After all programs have been reviewed, the blank display
will appear to allow entering another program. Another press of the
Prog. key will display the number of free programs available, such as
Fr 16 if 4 programs have been entered.
■ MANUAL OVERRIDE
TEMPORARY: While in the Run Mode, pressing the
key once
will reverse the output; ON to OFF or OFF to ON. The
symbol
appears in the display to indicate a temporary override. At the next
scheduled switching time, automatic control resumes, eliminating the
override.
CONTINUOUS: While in the Run Mode...
• Pressing the
key twice will turn the output to ON permanently.
symbol appears in display.
• Pressing the
key three times will turn the output OFF permanently.
symbol appears in display.
• To terminate a continuous override, press the
key until
appears in the display.
To delete only one or a few programs: Press Prog. key until the
desired program is displayed.
Press m key to :59 and press once more to blank out.
Press h key to 11PM and press once more to blank out.
Press
key, display will flash for several seconds and then enter
the Run Mode.
Using the reset key will delete ALL programs, the time of day, and
day of the week.
■ TROUBLESHOOTING
PROBLEM: Days are flashing, pressing any key does nothing
except
key turns output ON and OFF.
SOLUTION: Time of Day and Day of Week have not been set. See
“SETTING THE TIME”
NOTE: This is the condition after a reset. If the timer is found in this
condition after it has been installed, programmed and operating for a
while, it may indicate that electrical noise or voltage transients have
disrupted the microprocessor causing a loss of program information.
Call 1-800-272-1115 and request that a no-charge “Snubber Filter” be
sent to you to place across the input to the timer, which may solve the
problem.
A second, but very unlikely cause of loss of program is a power failure with the backup capacitor low or dead. Check by disconnecting
power and monitoring how long the capacitor keeps the time of day in
the display. Typically, the capacitor will maintain the time and programs for 4 days, but not more than 5 days.
PROBLEM: Time of day was set while holding the
but days are still flashing.
key down,
SOLUTION: Current day of week was not set while holding down
the
key. See “SETTING THE TIME”
PROBLEM: It is 10AM and a ON program for 8AM was entered, but
the output is not ON. Display shows the
and
symbols.
SOLUTION: After programming, the timer does not “look back” to
determine if it should be ON. Press the
key (temporary override)
to turn the output ON;
appears in display. The timer will
assume automatic operation at the next programmed event.
PROBLEM: A program for 8AM Monday thru Friday was entered,
is flashing.
but it will not accept it and
or OFF
was not entered as part of the
SOLUTION: The ON
program. ON or OFF must be selected.
Digi 20 Program Schedules
Prog
ON/OFF
h
m
Day(s)
_____________________________________________________________________________________________________________________________________________________________________________
1
On
7 am
30
Mon., Tue., Wed., Thurs, Fri.
_____________________________________________________________________________________________________________________________________________________________________________
_____________________________________________________________________________________________________________________________________________________________________________
_____________________________________________________________________________________________________________________________________________________________________________
_____________________________________________________________________________________________________________________________________________________________________________
_____________________________________________________________________________________________________________________________________________________________________________
_____________________________________________________________________________________________________________________________________________________________________________
_____________________________________________________________________________________________________________________________________________________________________________
_____________________________________________________________________________________________________________________________________________________________________________
_____________________________________________________________________________________________________________________________________________________________________________
_____________________________________________________________________________________________________________________________________________________________________________
MIL 72 Series
ELECTROMECHANICAL 24
HOUR & 7 DAY TIME SWITCHES
Same panel or flush mount configuration as the Digi 20.
21Amp, 2HP SPDT Switch.
Digi 42
7 DAY ELECTRONIC TIME
SWITCH
Similar to Digi 20, except has
Holiday program and automatic daylight time
changeover.
GM & GMX Series
MECHANICAL & ELECTRONIC
24 HOUR AND 7 DAY TIME
SWITCHES
30Amp & 21Amp in NEMA 1 or
NEMA 3R Enclosures.
Digi 42/2
TWO CHANNEL TIME
SWITCH
Same features as Digi 42
except it has two channels.
KM2 In-Wall Timer
24 HOUR OR 7 DAY
Replaces standard wall switch.
20Amp, 120VAC.
Digi 322
ONE, TWO OR FOUR
CHANNEL 365 DAY
ELECTRONIC
PROGRAMMABLE TIME
CONTROL
Automatic Daylight Time
changeover and many other
features.
FrostKing Refrigeration
Defrost Timers
Two models replace all standard
Paragon or Precision models.
GRÄSSLIN GmbH & Co. KG is ISO 9001 Certified
GRASSLIN CONTROLS CORPORATION
31 Industrial Ave. • Mahwah, New Jersey 07430 • Tel.: 201-825-9696 • Fax: 201-825-8694
E-mail: GCCsales@grasslin.com • www.grasslin.com
KLT 2005
MECHANICAL SPRING
WOUND COUNTDOWN
TIMER
Mounts in single or multigang electrical boxes with
standard or decorator
wallplates
Printed in USA 080US 10.99
Other Grasslin Time Control Products