BTI9170GL 90 cm Glass island cooker hood 1

BTI9170GL 90 cm Glass
island cooker hood
1
User Manual for your Baumatic
BTI9170GL
Cooker Hood
90 cm Glass island cooker hood in
stainless steel
NOTE: This User Instruction Manual contains important
information, including safety & installation points, which will
enable you to get the most out of your appliance. Please keep it
in a safe place so that it is easily available for future reference; for
you or any person not familiar with the operation of the appliance.
GS 21/08/13
2
Contents Page
Environmental note
4
IMPORTANT SAFETY INFORMATION
5–7
Specifications of your cooker hood
8
Using your Baumatic cooker hood
Before first use
To use your cooker hood
Setting the time of day
The timer
9 - 10
9
9 – 10
10
10
Cleaning your Baumatic cooker hood
The grease filters
11
11
Maintenance
Removing and cleaning the grease filters
Changing a light bulb
Fitting the carbon filter
12 - 15
12
13
14 - 15
Installation
Electrical connection
Before beginning installation
Positioning
Installing your cooker hood
Supplied installation components
16
16
17
18
19
20
Extraction mode or recirculation mode?
External ducting
23
23
Troubleshooting
24 – 25
Baumatic consumables
26
Contact details
27
- 22
- 17
– 18
- 19
- 22
3
ENVIRONMENTAL NOTE
Note: Before discarding an old appliance, switch off and
disconnect it from the power supply. Cut off and render any
plug useless. Cut the cable off directly behind the appliance to
prevent misuse. This should be undertaken by a competent
person.
CONFORMITY TO W.E.E.E. DIRECTIVE
4
IMPORTANT SAFETY INFORMATION
Your safety is of the utmost importance to Baumatic.
Please make sure that you read this instruction booklet
before attempting to install or use the appliance. If
you are unsure of any of the information contained in
this booklet, please contact the Baumatic Advice Line.
IMPORTANT: Any installation work must be
carried out by a qualified electrician or
competent person.
o The hood must be installed in accordance with the installation
instructions and all measurements followed.
o If the cooker hood is installed for use above a gas appliance then
the provision for ventilation must be in accordance with the Gas
Safety Codes of Practice BS.6172, BS.5440 & BS.6891 (Natural
Gas) and BS.5482 (LP Gas) 1994, the Gas Safety (Installation &
Use) Regulations, the Building Regulations issued by the
Department of the Environment, the Building Standards
(Scotland) (Consolidated) Regulations issued by the Scottish
Development Department.
o It is dangerous to alter the specifications or to modify this
product.
Do not tamper with it or attempt to modify the
appliance in any way.
o When installing the hood, ensure that the following
recommended distances are observed between the highest point
on the hob top (including the burners) and the bottom of the
cooker hood:
 Electric cookers:
 Gas cookers:
 Coal/ oil cookers:
700 mm
700 mm
800 mm
IMPORTANT: DO NOT SET YOUR COOKER HOOD LESS
THAN 700mm ABOVE YOUR COOKER.
o When installed between adjoining wall cabinets, the cabinets
must not overhang the hob.
5
o The edges of the cooker hood are sharp – be mindful of this as
you handle your appliance, especially during installation and
cleaning. DO NOT CLEAN IN BEHIND THE GREASE FILTERS!
o If the room where the cooker hood is to be used contains a fuel
burning appliance such as a central heating boiler then its flue
must be of the sealed or balanced flue type.
o If other types of flue or appliances are fitted, ensure that there is
an adequate supply of air in the room.
o When the hood is being used in its extractor function, ensure
that the ducting is fire retardant and that there are no bends
sharper than 90 degrees as this will reduce the efficiency of the
hood.
o Ensure the ducting for the extractor function has the same
diameter as the outlet hole all the way through.
o Keep young children from using, playing with
or tampering with the cooker hood. Older
children and infirm persons should be
supervised if they are using the cooker hood.
o Your cooker hood is for domestic use only.
o Please dispose of the packing material carefully – children are
especially vulnerable to it.
o Dirty oil is an even greater fire risk.
o Always put lids on pots and pans when cooking
on a gas cooker.
o The manufacturer refuses to accept any responsibility for
damages arising to the hood or it catching on fire, from a failure
to observe the fire safety advice contained in this instruction
booklet.
6
o Remember that when in extraction mode, your cooker hood is
removing air from your room. Ensure that proper ventilation
measures are being observed.
o Note that it removes odours from your room, not steam.
o Warning - Always ensure that the cooker
hood has been disconnected from the
power supply before carrying out any work
on the hood, including replacing light bulbs.
o Do not connect the ducting system of this appliance to any
existing ventilation system which is being used for any other
purpose.
o Do not install above a cooker with a high level grill.
o Never leave frying pans unattended during use
as overheated fats and oils might catch fire.
o The lights on this appliance should only be used
during operation of the cooker hood. They should not be left on
permanently and used as a lighting source.
o The cooker hood should not be exposed to a direct heat source
from the cooking device underneath it, i.e. naked flame from a
gas burner or heat from electric hob zones without a pan on
them.
o Do not attempt to use the cooker hood if it is damaged in any
way. Never attempt to use it without the grease filters fitted or
if the filters are excessively greasy!
o Never flambé cook under this cooker hood.
THE
MANUFACTURER
DECLINES
ALL
RESPONSIBILITY IN THE EVENT OF FAILURE TO
OBSERVE THE INSTRUCTIONS GIVEN HERE, FOR
INSTALLATION, MAINTENANCE AND SUITABLE
USE OF THE HOOD.
7
Specifications of your cooker hood
PRODUCT DIMENSIONS
Height:
Width:
Depth:
1010 mm * – 1150 mm**
900 mm
600 mm
DIMENSIONS OF CHIMNEY SECTION
270 mm x 285 mm
o
o
o
o
o
o
High extraction tangential motor
LCD display
Touch control operation
3 Speeds
2 Metallic grease filters
4 Halogen lights
o Extraction capacity: 1000 m³/hr
o Optional extra: 1 x SQ2 Carbon filter required for
recirculation mode
*IMPORTANT: Please see the positioning instructions on
pages 18 - 19 to obtain precise information on the height
requirements for this product.
** If you are using the appliance in recirculation mode, then PLEASE
NOTE that some of the vent in the upper chimney section must be
exposed. You will have to take this into account when calculating the
minimum height of the cooker hood when installed.
8
Using your Baumatic cooker hood
Before first use
IMPORTANT: THIS PROCESS MUST BE FOLLOWED
BEFORE THE COOKER HOOD IS USED FOR THE FIRST
TIME.
o You should use a good quality stainless steel cleaner and polish
on ALL of the stainless steel areas of your cooker hood, before it
is used for the first time.
o This will help to leave a silicone water-resistant film to protect
the stainless steel surfaces.
To use your cooker hood
o Make sure that it has been installed by a suitably qualified
person, as per the information contained in Baumatic’s
installation instructions.
o Find the control panel, which is located in the middle of the
canopy.
o There are several buttons on the control panel, which perform
separate functions.
o Press the Add/ON button to switch the cooker hood on. The hood
will start to run at its lowest speed.
o The cooker hood has three operating speeds; low, medium and
high. Use the Add/ON button to increase the speed and use the
Dec/OFF button to decrease the speed that it is operating at.
o The operating speed that you have selected will appear on the
LCD display.
o If you press the Dec/OFF button when the hood is operating at
its lowest speed, then the hood will switch off.
9
o Press the light button to switch the bulbs on and off. You can
switch the lights on, even if the hood is not operating.
IMPORTANT: IDEALLY YOU SHOULD SWITCH ON
YOUR HOOD TEN MINUTES BEFORE YOU START TO
COOK, OR AT THE VERY LEAST WHEN YOU BEGIN
COOKING. YOU SHOULD ALSO RUN YOUR HOOD FOR
TEN MINUTES AFTER YOU HAVE FINISHED COOKING.
Setting the time of day
o Press and hold the timer button, until the first two digits of the
display start to flash.
o Release the timer button, then use the Add/ON button and
Dec/OFF button to set the hour time.
o Press the timer button again and the second two digits of the
display will start to flash.
o Use the Add/ON button and Dec/OFF button to set the minute
time.
o Once the time of day is shown correctly on the display, press the
timer button for the third time to confirm it.
The timer
o You can use the cooker hood’s timer, to set the cooker hood to
run for a particular period of time and then switch off.
o You can get the cooker hood to countdown for the following
periods of time:No. of pushes of the timer
button
1
2
3
4
Length of time (in minutes)
the cooker hood will operate
for
5 minutes
15 minutes
30 minutes
Timer function cancelled
o Once you have set a countdown period, the cooker hood will
start to countdown. The time remaining until the cooker hood
shuts off will show on the display.
o When the countdown time has been reached, 00:00 will appear
and the cooker hood will stop running.
10
Cleaning your Baumatic cooker hood
IMPORTANT: BEFORE CLEANING, ALWAYS
ENSURE THAT YOU HAVE SWITCHED YOUR
COOKER HOOD OFF AT THE OMNI-POLAR
SWITCH, SET AT THE WALL FROM THE CABLE.
Cleaning
o Clean the external parts of your cooker hood with mild liquid
detergent and a new damp cloth.
o Never use abrasive powder, corrosive solvents or brushes.
o You should use a good quality stainless steel cleaner and polish
on ALL of the stainless steel areas of your cooker hood
o Never insert pointed objects into the motor’s protective grid.
o Only clean the control panel and grease filter grill with mild liquid
detergents and a new damp cloth.
o If you are using the appliance in recirculation mode, then be
sure to replace the carbon filter at the recommended interval
(see section on “Fitting the carbon filter”). A build up of grease
could cause a fire hazard.
o Never attempt to clean the area above the grease filters.
The grease filters
o Your cooker hood includes two grease filters which help to
absorb grease particles to protect your kitchen & furniture from
greasy residues.
o The metallic filters may become inflammable if they become
saturated with this greasy residue.
o To prevent this fire hazard, the filters should be cleaned
regularly. Depending on use, this should be done every 10-15
days or at least once a month, using hot water and normal
washing-up detergent.
o DO NOT WASH THE GREASE FILTERS IN A DISHWASHER.
11
Maintenance
Removing and cleaning the grease filters
o First remove the grease filters by
pulling down on the handle and
pulling them away from the
cooker hood.
o Soak the grease filters in hot water and washing up liquid for
about an hour.
o Rinse it off thoroughly with hot water.
o Repeat the process if required.
o Refit the grease filters once it has
dried.
o IMPORTANT: Let the grease filters dry thoroughly before
refitting it in the cooker hood.
12
Changing a light bulb
IMPORTANT: BEFORE ATTEMPTING TO CHANGE
A LIGHT BULB, YOU MUST ENSURE THAT YOU
HAVE DISCONNECTED THE COOKER HOOD FROM
YOUR MAINS SUPPLY.
o Remove the grease filters (as
described on page 12).
o Prior to touching the light bulbs ensure that they have cooled
down.
o Find the bulb that requires replacement, you will find it located in
the light fixture which is inside the exposed section of the
canopy.
o Use a screwdriver to remove the glass cover that sits over the
bulb. Unplug the light bulb that needs to be replaced and insert a
new G4 20W (max) bulb. Then replace the glass cover.
o IMPORTANT: Defective bulbs should be replaced immediately.
o If the lights still do not work, make sure that the bulbs are fitted
properly into their housings before you call for technical
assistance.
o Refit the grease filters.
13
Fitting the carbon filter
If the appliance is being used to be used in recirculation mode then it
is necessary to fit carbon filters. This will help to absorb unpleasant
odours caused by cooking.
IMPORTANT: BEFORE ATTEMPTING TO FIT OR
REMOVE THE CARBON FILTER, YOU MUST
ENSURE THAT YOU HAVE DISCONNECTED THE
COOKER HOOD FROM YOUR MAINS SUPPLY.
1) Remove the grease filters.
2) The line drawing above shows what you will see after removing the
grease filters.
o The carbon filter will be fitted over the motor casing hole and
there is a fixing point in the top right hand corner (both indicated
by arrows in the above drawing).
14
3) Use a screwdriver to take
out the two screws that go
through the fixing point and
then lower the carbon filter
over the motor casing hole.
o The corner with the
diagonal cut-out on it,
must be positioned
against the fixing point
(as shown in the above
picture).
o Retighten the two screws through the fixing point, into the
carbon filter. These screws must be fully tightened.
4) After fitting the
carbon filter, the
underneath of the
cooker hood
should appear as
in the drawing
opposite.
o Refit the grease filters.
o The carbon filters should be replaced approximately every three
months, if they show signs of damage, or if you start to notice
that cooking smells are entering the kitchen through the upper
vents.
15
Installation
IMPORTANT: Before installation and usage read
all the instructions and make sure that the
voltage (V) and the frequency (Hz) indicated on
the rating plate are exactly the same as the
voltage and frequency in your home. The rating
plate can be found behind the grease filter.
The manufacturer declines all responsibility in the event of the installer
failing to observe all the accident prevention regulations in force,
which are necessary for normal use and the regular operation of the
electric system.
Electrical connection
YOUR COOKER HOOD IS INTENDED FOR FITTED AND
PERMANENT INSTALLATION.
o The cooker hood’s power cable must be fitted upstream from the
electrical connection, using an omni-polar switch with a contact
distance of at least 3 mm. THE FUSE MUST BE RATED AT 3
AMPS.
WARNING: THIS APPLIANCE MUST BE EARTHED. It
should only be connected by a competent person, using
fixed wiring via a double pole switched fused spur outlet.
(UK ONLY).
We recommend that the appliance is connected by a qualified
electrician, who is a member of the N.I.C.E.I.C. and who will comply
with the I.E.E. and local regulations. The wires in the mains lead are
coloured in accordance with the following UK code:
Blue = Neutral, Brown = Live, Green/Yellow = Ground
If you only find two wires in the main’s lead (blue and brown),
then neither must be connected to the earth terminal.
16
o As the colours of the wires in the appliance’s mains lead may not
correspond with the coloured markings identifying the terminals in
your spur box, please proceed as follows:
o The blue wire must be connected to the
terminal marked “N” (neutral), or coloured
black.
o The brown wire must be connected to the
terminal marked “L” (live), or coloured red.
Before beginning installation
o Check that the product purchased is of a suitable size for the
chosen installation area. In addition check whether there is an
electrical socket available that will be accessible once the hood is
mounted. If the product is going to be used in extraction mode,
then there should also be space to connect a ducting hose to the
outside.
o Carry out all necessary masonry work prior to the fitting of the
cooker hood.
o Ensure that all electrical connections are carried out by a suitably
qualified person.
o Check inside the product and ensure that there is no transit
packaging or any other materials, such as packets of screws,
guarantees etc. These should be removed and kept for future use.
o If possible, disconnect and move freestanding or slot-in cookers
from their position, to provide easier access to the ceiling. If this is
not possible, then a thick, protective covering should be placed over
the worktop, hob top or cooker. This will help to protect these
surfaces from damage and debris.
o Select a flat surface for assembling the cooker hood. Cover that
surface with a protective covering and place all cooker hood parts
and fittings on it.
o Wall plugs are provided to secure the hood to most types of
ceilings. However a qualified technician must verify the suitability of
the materials, in accordance with the type of ceiling. The ceiling
must be strong enough to take the weight of the hood.
o Do not tile, grout or silicone this appliance to the ceiling. This
appliance is designed to be surface mounted only.
17
o Remove any protective wrapping that has been put on the cooker
hood or chimney sections, to protect them during transit.
Positioning
X
=
A
=
B
=
C
=
6.5 cm =
Height of the appliance
Total height of the kitchen
Height of the worktop
Distance between the hob and the hood
Height of the hood canopy
o To work out the height of the appliance, you need to use the
following formula: X = A – (B + C + 6.5 cm).
o The overall height of the appliance should be calculated
according to the height of the chimney sections. You must allow
yourself sufficient space to make the electrical connections and
connecting the ducting hose (if required).
IMPORTANT: Your ceiling should have a minimum
height of 2.4 metres, otherwise you may encounter
difficulties when installing the appliance.
18
Installing your cooker hood
IMPORTANT: YOU WILL HAVE TO DECIDE BEFORE
INSTALLING YOUR COOKER HOOD WHETHER TO USE
IT IN EXTRACTION MODE OR RECIRCULATION
MODE. PLEASE TURN TO PAGE 23 NOW TO
UNDERSTAND THE DIFFERENCES BETWEEN THESE
TWO MODES.
o We recommend that two people install this hood.
o Your cooker hood should only be suspended from ceiling joists or
joints between joists that are weight bearing. DO NOT hang this
hood from a suspended ceiling.
o IMPORTANT: The ceiling MUST be able to withstand a weight of
at least 40 kilograms.
o IMPORTANT: The ceiling MUST be at least 30 mm thick.
o It must be positioned at least 700 mm above the hob
underneath it. You cannot fit this product by securing it between
two cupboards.
o If you are using your cooker hood in extraction mode, then you
will need to make the necessary arrangements for the ducting,
before the rest of the installation.
IMPORTANT: YOUR COOKER HOOD SHOULD BE CONNECTED
TO YOUR MAINS SUPPLY AFTER THE REST OF THE
INSTALLATION PROCESS HAS BEEN COMPLETED.
19
Supplied installation components
1) Position the hanging plate on the
ceiling and then mark the position of the
screw holes.
o The hanging plate should be
securely fixed to the ceiling, using
the 12 x ST6 (40 mm) screws.
o Depending on the surface of the ceiling that you are fixing the
hanging plate to, you may need to use 8 x expansion bolts (for
concrete).
20
2) Fix the angle bars to the hanging plate,
using the 8 x M4 nuts and bolts with metal
washers.
3) Extend the angle bars to the required height
and then fix them in position using the 16 x M4
nuts and bolts with metal washers.
o IMPORTANT: The angle bars must have an
overlap of AT LEAST 100 mm.
4) If your cooker hood is going to be used in
extraction mode, then you should connect the
ducting hose to the ceiling adaptor at this point.
o Fix the upper chimney section to the
hanging plate, using the 4 x self tapping
screws.
o Slide the lower chimney section onto the
angle bars and raise it until it sits just below
the upper chimney section.
o Use the hanging hook to temporarily keep the lower chimney
section in this position, to make sure that it does not drop down
whilst fixing the main body of the hood to the angle bars.
21
5) If the glass canopy has not been preassembled by the factory, then it should be
fixed to the top of the main body of the
cooker hood at this stage.
6) Lift the main body of the cooker hood onto
the angle bar and then fix it into position using
the 16 x M4 bolts.
o IMPORTANT: This stage of the
installation process MUST be
completed by two people.
o IMPORTANT: The 16 x M4 bolts
MUST be securely tightened.
7) If you are going to be using the hood in
extraction mode, you should fix the ducting
hose to the spigot.
o The electrical connection must
correspond to the electrical
requirement noted on the rating plate,
which is placed inside the cooker hood.
The appliance should now be connected
to the electrical supply. See page 16 –
17 for detailed information on the
electrical connection.
o Check that the appliance is operating correctly by selecting each
speed and switching the light bulbs on and off.
o Remove the hanging hook and then slide the lower chimney
section downwards, until it rests against the main body of the
cooker hood.
o Use a stainless steel cleaner and polish on the stainless steel
sections of the appliance.
o If you are using the appliance in recirculation mode, then you
should now fit the carbon filter. See the “Fitting the carbon filter”
section on pages 14 - 15.
22
Extraction mode or recirculation mode?
What is the difference between extraction and recirculation
modes?
To get optimum performance from your cooker, the air will be taken
out of the room via external ducting.
Unfortunately if you live in a flat or the hood is too far from an outside
wall, this may not be possible. The only alternative is to recirculate the
air.
In recirculation mode stale air is taken via the grease filter, and passed
through a charcoal filter for purification. The air then re-enters the
kitchen via an opening in the hood.
What is a charcoal filter and do I need one?
All cooker hoods have a grease filter but if you are using your cooker
hood in recirculation mode, then a charcoal filter must be fitted in
addition to the grease filter.
External ducting
o Connect the spigot to the top of the cooker hood, and then
connect a 125 mm ducting hose to the coupling (please note that
the ducting hose is not supplied with the appliance).
o The other end of the ducting hose should be connected to a
discharge outlet that is suitable for cooking vapours. It should
have a cross section of at least 150 cm².
o The maximum distance between the coupling and your discharge
outlet should be 3 metres, with one 90 degree bend.
o For each additional 90 degree bend that is made, the maximum
distance between the coupling and your discharge outlet is
reduced by 1 metre.
23
Troubleshooting
IMPORTANT: If your cooker hood appears not to be operating
properly, before contacting Baumatic Customer Care, please
refer to the checklist below.
My cooker hood will not start.
o Check that the hood is connected to the electricity supply
o Check that the fan speed control is set correctly.
My cooker hood is not working effectively.
o The fan speed is not set high enough
o The grease filters are dirty and require cleaning.
o The kitchen is not well ventilated enough.
o If the hood is set up for recirculation mode, check that the
carbon filters do not need replacing.
o If the hood is set up for extraction mode, check that the ducting
hose and discharge outlet are not blocked.
My cooker hood has switched off during operation.
o The safety cut-out device has been tripped.
o Turn off the hob and then wait for the safety cut-out device to
reset.
o IMPORTANT: If you have installed your cooker hood too low,
the safety cut-out device will frequently trip. Your cooker hood
may become damaged if the safety cut-out device is tripped
frequently.
o The timer has been accidentally set to switch the cooker hood off
automatically.
24
IMPORTANT: If your appliance appears not to be
operating correctly, then you should disconnect it
from your mains supply and then contact
Baumatic Customer Care on telephone number
(0118) 933 6911.
DO NOT ATTEMPT TO REPAIR THE APPLIANCE
YOURSELF.
Please note that if an engineer is asked to attend whilst the product is
under guarantee and finds that the problem is not the result of an
appliance fault, then you may be liable for the cost of the call out
charge.
The appliance must be accessible for the engineer to perform
any necessary repair. If your appliance is installed in such a
way that an engineer is concerned that damage will be caused
to the appliance or your kitchen, then they will not complete a
repair.
This includes situations where appliances have been tiled in,
sealed in with sealant, have wooden obstructions placed in
front of the appliance, like plinths. Or any installation other
than the one specified by Baumatic Ltd. has been completed.
Please refer to the conditions of guarantee that appear on the
warranty card that you receive with the appliance.
25
Baumatic Consumables
o BC001 Degreaser for Dishwashers (200 g)
o BC002 Descaler for Washing Machines and Dishwashers (200 g)
o BC003 Ceramic Hob Cleaner (250 ml)
o BC004 Oven Cleaner (250 ml)
o BC005 Stainless Steel Cleaner and Protector (250 ml)
o BC007 E-Cloth – General Purpose Cloth
o BC008 Microwave Cover
To order a Baumatic consumable product please call 0123 5437 244
and quote the product code. You can also order online from
eshop.baumatic.co.uk
26
United Kingdom
Baumatic Ltd.,
Baumatic Buildings,
6 Bennet Road,
Reading, Berkshire
RG2 0QX
United Kingdom
Sales Telephone
(0118) 933 6900
Sales Fax
(0118) 931 0035
Customer Care Telephone
(0118) 933 6911
Customer Care Fax
(0118) 986 9124
Spares Telephone
(01235) 437244
Advice Line Telephone
(0118) 933 6933
E-mail:
sales@baumatic.co.uk
customercare@baumatic.co.uk
spares@baumatic.co.uk
technical@baumatic.co.uk
Website:
www.baumatic.co.uk
Facebook:
www.facebook.com/baumatic.uk
Republic of Ireland
Service Telephone
1-890 812 724
Spares Telephone
091 756 771
Czech Republic/Slovakia
Baumatic s.r.o.
Lípová 665/1
460 01 Liberec 4
Czech Republic
Panenská 34
811 03 Bratislava - Staré Mesto
Slovakia
+420 483 577 200 (CZ)
+421 255 640 618 (SK)
www.baumatic.cz
www.baumatic.sk
Germany
Kundendienst & Ersatzteile
Deutschland 0049(0)180-5888975
Oesterreich +43 (0) 820 / 420423
www.baumatic.de
Italy
Baumatic Italia S.R.L.
Via Galvani N.3
35011 Campodarsego (PD)
+3904 9920 2297
www.baumatic.it
Holland
Baumatic Benelux B.V.
Dukdalfweg 15d
1332 BH ALMERE
Nederland
+31(0)36 549 1553/1555
www.baumatic.nl
28
29
30
31
32
Download PDF
Similar pages
Mora OO 463 X
Mora OK 673 GW cooker hood
 #4008 - Reddy Apple Cooker
HQ W4-49900/4
HQ W4-49902/4
DeLonghi SGGX 854 cooker
DeLonghi SEX 8542 cooker
 #4008 - Reddy Apple Cooker