HP Compaq Presario,Presario 6010 System information

Compaq Presario CQ40 Notebook PC
Maintenance and Service Guide
© Copyright 2008 Hewlett-Packard
Development Company, L.P.
Athlon, Sempron, and Turion are trademarks
of Advanced Micro Devices, Inc. Bluetooth is
a trademark owned by its proprietor and used
by Hewlett-Packard Company under license.
Intel and Core are trademarks of Intel
Corporation in the U.S. and other countries.
Microsoft, Windows, and Windows Vista are
U.S. registered trademarks of Microsoft
Corporation. SD Logo is a trademark of its
proprietor.
The information contained herein is subject
to change without notice. The only
warranties for HP products and services are
set forth in the express warranty statements
accompanying such products and services.
Nothing herein should be construed as
constituting an additional warranty. HP shall
not be liable for technical or editorial errors
or omissions contained herein.
First Edition: August 2008
Document Part Number: 468153-001
Safety warning notice
WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not
place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a
hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft
surface, such as pillows or rugs or clothing, to block airflow. Also, do not allow the AC adapter to contact
the skin or a soft surface, such as pillows or rugs or clothing, during operation. The computer and the
AC adapter comply with the user-accessible surface temperature limits defined by the International
Standard for Safety of Information Technology Equipment (IEC 60950).
iii
iv
Safety warning notice
Table of contents
1 Product description
2 External component identification
Top components ................................................................................................................................... 6
TouchPad ............................................................................................................................ 6
Lights ................................................................................................................................... 7
Buttons and speakers .......................................................................................................... 8
Keys ................................................................................................................................... 10
Display ............................................................................................................................... 11
Wireless antennae (select models only) ............................................................................ 12
Front components .............................................................................................................................. 13
Left-side components ......................................................................................................................... 14
Rear component ................................................................................................................................. 15
Right-side components ....................................................................................................................... 15
Bottom components ........................................................................................................................... 16
3 Illustrated parts catalog
Serial number location ........................................................................................................................ 17
Computer major components ............................................................................................................. 18
Display assembly components ........................................................................................................... 24
Plastics Kit .......................................................................................................................................... 25
Mass storage devices ......................................................................................................................... 26
Miscellaneous parts ............................................................................................................................ 27
Sequential part number listing ............................................................................................................ 28
4 Removal and replacement procedures
Preliminary replacement requirements ............................................................................................... 33
Tools required .................................................................................................................... 33
Service considerations ....................................................................................................... 33
Plastic parts ....................................................................................................... 33
Cables and connectors ..................................................................................... 34
Drive handling ................................................................................................... 34
Grounding guidelines ......................................................................................................... 35
v
Electrostatic discharge damage ........................................................................ 35
Packaging and transporting guidelines ............................................. 36
Workstation guidelines ..................................................................... 36
Equipment guidelines ....................................................................... 37
Unknown user password ................................................................................................... 38
Component replacement procedures ................................................................................................. 39
Serial number .................................................................................................................... 39
Computer feet .................................................................................................................... 40
Battery ............................................................................................................................... 41
Optical drive ....................................................................................................................... 42
Hard drive .......................................................................................................................... 44
WLAN module .................................................................................................................... 47
RTC battery ....................................................................................................................... 50
Memory module ................................................................................................................. 52
Keyboard ........................................................................................................................... 54
Switch cover ...................................................................................................................... 56
Speaker assembly ............................................................................................................. 58
Display assembly ............................................................................................................... 60
Camera/microphone module ............................................................................................. 65
Top cover ........................................................................................................................... 67
TouchPad button board ..................................................................................................... 70
Bluetooth module ............................................................................................................... 71
Modem module .................................................................................................................. 73
Audio board ....................................................................................................................... 74
USB board ......................................................................................................................... 75
Power connector cable ...................................................................................................... 77
System board ..................................................................................................................... 79
Fan/heat sink assembly ..................................................................................................... 82
Processor ........................................................................................................................... 85
System fan ......................................................................................................................... 86
5 Setup Utility
Starting the Setup Utility ..................................................................................................................... 88
Changing the language of the Setup Utility ........................................................................................ 88
Navigating and selecting in the Setup Utility ...................................................................................... 89
Displaying system information ............................................................................................................ 89
Restoring default settings in the Setup Utility ..................................................................................... 90
Exiting the Setup Utility ...................................................................................................................... 90
Setup Utility menus ............................................................................................................................ 91
6 Specifications
Computer specifications ..................................................................................................................... 93
14.1-inch, WXGA, BrightView display specifications .......................................................................... 94
vi
Hard drive specifications .................................................................................................................... 95
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive specifications ................................. 96
System DMA specifications ................................................................................................................ 97
System interrupt specifications—Intel processors .............................................................................. 98
System interrupt specifications—AMD processors ............................................................................ 99
System I/O address specifications—Intel processors ...................................................................... 100
System I/O address specifications—AMD processors ..................................................................... 102
System memory map specifications—Intel processors .................................................................... 104
System memory map specifications—AMD processors ................................................................... 104
7 Screw listing
Black Phillips PM2.5×4.0 screw ....................................................................................................... 107
Black Phillips PM2.5×6.0 captive screw ........................................................................................... 109
Black Phillips PM2.0×2.0 broad head screw .................................................................................... 110
Silver Phillips PM1.5×9.0 screw ....................................................................................................... 111
Black Phillips PM2.5×3.0 screw ....................................................................................................... 112
Black Phillips PM2.5×17.0 screw ..................................................................................................... 113
Black Phillips PM2.5×6.0 screw ....................................................................................................... 114
Black Phillips PM2.5×7.0 screw ....................................................................................................... 115
Silver Phillips PM3.0×4.0 screw ....................................................................................................... 118
Silver Phillips PM2.0×4.0 screw ....................................................................................................... 119
Black Phillips PM2.0×4.0 screw ....................................................................................................... 120
Silver Phillips PM2.0×10.0 captive screw ......................................................................................... 123
8 Backup and recovery
Recovering system information ........................................................................................................
Backing up your information ............................................................................................
When to back up .............................................................................................
Backup suggestions ........................................................................................
124
124
124
125
Using system restore points ............................................................................ 125
When to create restore points ........................................................ 125
Create a system restore point ........................................................ 125
Restore to a previous date and time ............................................... 126
Creating recovery discs ................................................................................................... 126
Performing a recovery ..................................................................................................... 127
Recovering from the recovery discs ................................................................ 127
Recovering from the dedicated recovery partition (select models only) .......... 127
9 Connector pin assignments
Audio-out (headphone) ..................................................................................................................... 129
Audio-in (microphone) ...................................................................................................................... 129
External monitor ............................................................................................................................... 130
RJ-11 (modem) ................................................................................................................................ 131
vii
RJ-45 (network) ................................................................................................................................ 131
HDMI ................................................................................................................................................ 132
Universal Serial Bus ......................................................................................................................... 132
10 Power cord set requirements
Requirements for all countries or regions ......................................................................................... 134
Requirements for specific countries or regions ................................................................................ 135
11 Recycling
Battery .............................................................................................................................................. 136
Display .............................................................................................................................................. 136
Index ................................................................................................................................................................. 142
viii
1
Product description
Category
Description
Product Name
Compaq Presario CQ40 Notebook PC
Processors
Intel® Core™ 2 Duo processors
Intel models
√
T9600 2.80-GHz, 6-MB L2 cache, 1066MHz FSB
√
T9400 2.53-GHz, 6-MB L2 cache, 1066MHz FSB
√
T8600 2.40-GHz, 3-MB L2 cache, 1066MHz FSB
√
T8400 2.26-GHz, 3-MB L2 cache, 1066MHz FSB
√
T7350, 2.00-GHz, 3-MB L2 cache, 1066MHz FSB
√
AMD models
with UMA
graphics
√
AMD models
with discrete
graphics
√
AMD processors
Chipset
Turion™ Ultra ZM-86 2.4-GHz, 2 × 1-MB
L2 cache, 3600-MHz FSB
√
√
Turion Ultra ZM-82 2.2-GHz, 2 × 1-MB L2
cache, 3600-MHz FSB
√
√
Turion Ultra ZM-80 2.1-GHz, 2 × 1-MB L2
cache, 3600-MHz FSB
√
√
Turion RM-70 2.00-GHz, 2 × 512-KB L2
cache, 3600-MHz FSB
√
√
Athlon™ QL-60 1.9-GHz, 2 × 512-KB L2
cache, 3600-MHz FSB
√
√
Sempron™ SI-40 2.0-GHz, 512-KB L2
cache, 3600-MHz FSB
√
√
Northbridge: Intel GM45
√
Southbridge: Intel ICH9m
√
Northbridge: AMD M780G
√
Northbridge: AMD M770
√
Southbridge: SB700
√
√
1
Category
Description
Graphics
Intel Graphics, Intel
Intel models
AMD models
with UMA
graphics
AMD models
with discrete
graphics
√
UMA (integrated) with shared video
memory:
●
Up to 251 MB on computers with
1024 MB of system memory
●
Up to 358 MB on computers with
more than 2048 MB of system
memory
Memory size is a dynamic change.
ATi Discrete PCI Express x 16
Graphics
√
(32Mx16 DDR2 x 4 PCs)
Memory size is a dynamic change.
AMD internal Graphics with Layout
"Sideport" memory (ATI Radeon HD
3200 Graphics)
●
Up to 251 MB on computers with
1024 MB of system memory
●
Up to 358 MB on computers with
more than 2048 MB of system
memory
√
Memory size is a dynamic change.
Panel
14.1-inch, WXGA with BrightView (1200
× 800)
√
√
√
Memory
2 SODIMM slots
√
√
√
Customer-accessible/upgradable
√
√
√
Supports up to 8 GB of system RAM
√
√
√
DDRII PC2-6400 (800-MHz)
√
√
√
Supports the following configurations:
√
√
√
Supports 9.5-mm, 2.5-inch hard drives
√
√
√
Serial ATA
√
√
√
Supports the following drives:
√
√
√
Hard drives
2
●
4096 (2048 × 2)
●
2048 (2048 × 1)
●
2048 (1024 × 2)
●
1024 (1024 × 1)
●
1024 (512 × 2)
●
512 (512 × 1)
Chapter 1 Product description
Category
Optical drives
Description
●
320 GB, 5400 rpm
●
250 GB, 5400 rpm
●
160 GB, 5400 rpm
●
120 GB, 5400 rpm
Intel models
AMD models
with UMA
graphics
AMD models
with discrete
graphics
Fixed (removal of one screw required)
√
√
√
SATA
√
√
√
12.7-mm tray load
√
√
√
Supports the following drives:
√
√
√
●
DVD±RW and CD-RW Super Multi
Double-Layer Combo Drive with
LightScribe
●
DVD±RW and CD-RW Super Multi
Double-Layer Combo Drive
●
DVD±RW and CD-RW Combo
Drive
Diskette drive
Supports external USB drive only
√
√
√
Camera
VGA camera
√
√
√
Fixed (no tilt)
√
√
√
640 × 480 by 24 frames per second
√
√
√
Microphone
One microphone, analog
√
√
√
Audio
HD audio
√
√
√
Supports Windows Vista® Premium
Logo requirements
√
√
√
Presario-branded Altec Lansing
speakers
√
√
√
56K V.92 data/fax modem
√
√
√
Supports all worldwide certification
requirements
√
√
√
Ethernet
Integrated 10/100 network interface card
(NIC)
√
√
√
Wireless
Integrated wireless local area network
(WLAN) options by way of wireless
module:
Intel WiFi Link 5100 802.11a/g/n WLAN
module
√
√
Intel WiFi Link 5100 802.11a/g/n WLAN
module + Bluetooth
√
√
Broadcom 4321 802.11a/b/g/n WLAN
module
√
√
Modem
√
3
Category
External media
card
Ports
Keyboard/pointing
devices
Power
requirements
Description
Intel models
4
AMD models
with discrete
graphics
Broadcom BCM4312 WLAN + Bluetooth
√
√
√
Digital Media Slot, supports SD, MMC,
MS, MSpro, xD
√
√
√
One full-size Mini Card slot
√
√
√
Audio-in (mono microphone)
√
√
√
Audio-out (stereo headphone)
√
√
√
RJ-45 (Ethernet, includes link and activity
lights)
√
√
√
USB (2)
√
√
√
VGA (Dsub 15-pin)
√
√
√
Smart-pin AC adapter plug
√
√
√
Hot plug/unplug and auto detect for
correct output to wide-aspect vs.
standard aspect video
√
√
√
HDMI v1.3 supporting 1080p with HDCP
key
√
√
√
14.1-inch keyboard
√
√
√
TouchPad with 2 buttons and 2-way scroll
(taps enabled as default)
√
√
√
6-cell 2.20-Ah Li-ion battery
√
√
√
65-W AC adapter with Smart-Pin DC
connector
√
90-W AC adapter with Smart-Pin DC
connector
Security
Security cable slot
Operating system
Preinstalled:
Serviceability
AMD models
with UMA
graphics
√
√
√
√
√
Free DOS
√
√
√
RedFlag
√
√
√
Windows Vista Home Basic (32-bit)
√
√
√
Windows Vista Home Premium (32- and
64-bit)
√
End-user replaceable parts:
AC adapter
√
√
√
Battery (system)
√
√
√
Hard drive
√
√
√
Memory module
√
√
√
Chapter 1 Product description
Category
Description
Intel models
AMD models
with UMA
graphics
AMD models
with discrete
graphics
Optical drive
√
√
√
Mini Card
√
√
√
5
2
External component identification
Top components
TouchPad
Component
Description
(1)
●
White: TouchPad is enabled.
●
Amber: TouchPad is disabled.
TouchPad light
(2)
TouchPad*
Moves the pointer and selects or activates items on the screen.
(3)
Left TouchPad button*
Functions like the left button on an external mouse.
(4)
TouchPad on/off button
Enables/disables the TouchPad.
(5)
TouchPad scroll zone*
Scrolls up or down.
(6)
Right TouchPad button*
Functions like the right button on an external mouse.
*This table describes factory settings. To view or change pointing device preferences, select Start > Control Panel > Hardware
and Sound > Mouse.
6
Chapter 2 External component identification
Lights
Component
Description
(1)
●
On: The computer is on.
●
Blinking: The computer is in the Sleep state.
●
Off: The computer is off or in Hibernation.
●
On: A battery is charging.
●
Blinking: A battery that is the only available power source has
reached a low battery level or a critical battery level.
●
Off: If the computer is plugged into an external power source,
the light is turned off when all batteries in the computer are
fully charged. If the computer is not plugged into an external
power source, the light stays off until the battery reaches a
low battery level.
●
Blinking: The hard drive or optical drive is being accessed.
●
On: HP ProtectSmart Hard Drive Protection has temporarily
parked the internal hard drive.
(2)
(3)
Power lights (2)*
Battery light
Drive light
(4)
Caps lock light
On: Caps lock is on.
(5)
Wireless light
●
Blue: An integrated wireless device, such as a wireless local
area network (WLAN) device and/or a Bluetooth® device, is
on.
●
Amber: All wireless devices are off.
●
White: Computer sound is turned on.
●
Amber: Computer sound is turned off.
(6)
(7)
Volume mute light
Volume down light
On: The volume scroll zone is being used to decrease speaker
volume.
Top components
7
Component
Description
(8)
Volume up light
On: The volume scroll zone is being used to increase speaker
volume.
(9)
Num lock light
On: Num lock is on or the embedded numeric keypad is enabled.
*The 2 power lights display the same information. The light on the power button is visible only when the computer is open. The
power light on the front of the computer is visible whether the computer is open or closed.
Buttons and speakers
Component
Description
(1)
Speakers (2)
Produce sound.
(2)
Power button*
●
When the computer is off, press the button to turn on the
computer.
●
When the computer is on, briefly press the button to initiate
Sleep.
●
When the computer is in the Sleep state, briefly press the
button to exit Sleep.
●
When the computer is in Hibernation, briefly press the button
to exit Hibernation.
If the computer has stopped responding and Windows® shutdown
procedures are ineffective, press and hold the power button for at
least 5 seconds to turn off the computer.
To learn more about your power settings, select Start > Control
Panel > System and Maintenance > Power Options.
(3)
8
Media button
Chapter 2 External component identification
●
Launches the QuickPlay program (for models with QuickPlay
preinstalled).
●
Launches the DVDPlay program (for models with DVDPlay
preinstalled).
Component
Description
NOTE: If the computer has been set up to require a logon
password, you may be asked to log on to Windows. QuickPlay or
DVDPlay launches after you log on. Refer to the QuickPlay or
DVDPlay software Help for more information.
(4)
Wireless button
Turns the wireless feature on or off but does not establish a
wireless connection.
NOTE: A wireless network must be set up in order to establish a
wireless connection.
(5)
Volume mute button
Mutes and restores speaker sound.
(6)
Volume scroll zone
Adjusts speaker volume. Slide your finger to the left to decrease
volume and to the right to increase volume. You can also tap the
minus sign on the scroll zone to decrease volume, or tap the plus
sign on the scroll zone to increase volume.
*This table describes factory settings. For information about changing factory settings, refer to the user guides located in Help
and Support.
Top components
9
Keys
NOTE:
10
Your computer may look slightly different from the illustration in this section.
Component
Description
(1)
esc key
Displays system information when pressed in combination with
the fn key.
(2)
fn key
Executes frequently used system functions when pressed in
combination with a function key or the esc key.
(3)
Windows logo key
Displays the Windows Start menu.
(4)
Embedded numeric keypad keys
Can be used like the keys on an external numeric keypad.
(5)
Windows applications key
Displays a shortcut menu for items beneath the pointer.
(6)
Navigation keys (home, pg up, pg down)
Execute volume mute, volume up, or volume down when pressed
in combination with the fn key.
(7)
Function keys
Execute frequently used system functions when pressed in
combination with the fn key.
Chapter 2 External component identification
Display
NOTE:
Your computer may look slightly different from the illustration in this section.
Component
Description
(1)
Internal display switch
Turns off the display if the display is closed while the computer is
turned on.
(2)
Internal microphones (2)
Record sound.
NOTE: If there is a microphone icon next to each microphone
opening, your computer has internal microphones.
Depending on your computer model, the computer may have 1 or
2 internal microphones.
(3)
Integrated webcam light
On: The integrated webcam is in use.
(4)
Integrated webcam
Records video and captures still photographs.
Top components
11
Wireless antennae (select models only)
On select computer models, at least 2 antennae send and receive signals from one or more wireless
devices. These antennae are not visible from the outside of the computer.
NOTE: For optimal transmission, keep the areas immediately around the antennae free from
obstructions.
To see wireless regulatory notices, refer to the section of the Regulatory, Safety and Environmental
Notices that applies to your country or region. These notices are located in Help and Support.
12
Chapter 2 External component identification
Front components
NOTE:
Your computer may look slightly different from the illustration in this section.
Component
Description
(1)
●
On: The computer is on.
●
Blinking: The computer is in the Sleep state.
●
Off: The computer is off or in Hibernation.
●
On: A battery is charging.
●
Blinking: A battery that is the only available power source has
reached a low battery level or a critical battery level.
●
Off: If the computer is plugged into an external power source,
the light is turned off when all batteries in the computer are
fully charged. If the computer is not plugged into an external
power source, the light stays off until the battery reaches a low
battery level.
●
Blinking: The hard drive or optical drive is being accessed.
●
On: HP ProtectSmart Hard Drive Protection has temporarily
parked the internal hard drive.
(2)
(3)
Power light
Battery light
Drive light
(4)
Audio-in (microphone) jack
Connects an optional computer headset microphone, stereo array
microphone, or monaural microphone.
(5)
Audio-out (headphone) jack
Produces sound when connected to optional powered stereo
speakers, headphones, ear buds, a headset, or television audio.
Front components
13
Left-side components
NOTE:
Your computer may look slightly different from the illustration in this section.
Component
Description
(1)
Attaches an optional security cable to the computer.
Security cable slot
NOTE: The security cable is designed to act as a deterrent, but
it may not prevent the computer from being mishandled or stolen.
(2)
External monitor port
Connects an external VGA monitor or projector.
(3)
Expansion port 3 (select models only)
Connects the computer to an optional docking device or optional
expansion product.
NOTE: The computer has only one expansion port. The term
expansion port 3 describes the type of expansion port.
(4)
RJ-45 (network) jack
Connects a network cable.
(5)
HDMI port
Connects an optional video or audio device, such as a highdefinition television, or any compatible digital or audio component.
(6)
eSATA/USB port (select models only)
Connects high-performance eSATA components, such as an
eSATA external hard drive, or connects an optional USB device.
NOTE: Depending on your computer model, the computer may
include a USB port only.
(7)
Digital Media Slot light
On: A digital card is being accessed.
(8)
Digital Media Slot
Supports the following optional digital card formats:
(9)
14
ExpressCard slot (select models only)
Chapter 2 External component identification
●
Memory Stick (MS)
●
Memory Stick Pro (MSP)
●
MultiMediaCard (MMC)
●
Secure Digital (SD) Memory Card
●
xD-Picture Card (XD)
Supports optional ExpressCards.
Rear component
Component
Description
Vent
Enables airflow to cool internal components.
NOTE: The computer fan starts up automatically to cool internal
components and prevent overheating. It is normal for the internal fan to
cycle on and off during routine operation.
Right-side components
NOTE:
Your computer may look slightly different from the illustration in this section.
Component
Description
(1)
Optical drive light
Blinking: The optical drive is being accessed.
(2)
Optical drive
Reads optical discs and, on select models, also writes to optical
discs.
(3)
USB ports (2)
Connect optional USB devices.
(4)
RJ-11 (modem) jack (select models only)
Connects a modem cable.
(5)
Power connector
Connects an AC adapter.
Rear component
15
Bottom components
Component
Description
(1)
Holds the hard drive and, for select models only, the wireless LAN
(WLAN) device.
Hard drive and WLAN module compartment
CAUTION: To prevent an unresponsive system, replace the
wireless module only with a wireless module authorized for use in
the computer by the governmental agency that regulates wireless
devices in your country or region. If you replace the module and
then receive a warning message, remove the module to restore
computer functionality, and then contact technical support through
Help and Support.
(2)
Memory module compartment
Contains the 2 memory module slots.
(3)
Mini Card compartment
Holds a WLAN device (select models only).
CAUTION: To prevent an unresponsive system, replace the
wireless module only with a wireless module authorized for use in
the computer by the governmental agency that regulates wireless
devices in your country or region. If you replace the module and
then receive a warning message, remove the module to restore
computer functionality, and then contact technical support through
Help and Support.
(4)
Battery release latch
Releases the battery from the battery bay.
(5)
Battery bay
Holds the battery.
(6)
Vents (4)
Enable airflow to cool internal components.
NOTE: The computer fan starts up automatically to cool internal
components and prevent overheating. It is normal for the internal
fan to cycle on and off during routine operation.
16
Chapter 2 External component identification
3
Illustrated parts catalog
Serial number location
When ordering parts or requesting information, provide the computer serial number and model number
located on the bottom of the computer.
Serial number location
17
Computer major components
18
Item
Description
(1)
14.1-inch, WXGA, BrightView display assembly
Chapter 3 Illustrated parts catalog
Spare part number
Item
Description
Spare part number
NOTE: See Display assembly components on page 24 for more display assembly
internal component spare part information.
For use only in computer models with Intel processors and a camera module
487281-001
For use only in computer models with Intel processors without a camera module
487280-001
For use only in computer models with AMD processors, discrete graphics subsystems, and
a camera module
487353-001
For use only in computer models with AMD processors, discrete graphics subsystems,
without a camera module
487352-001
For use only in computer models with AMD processors, UMA graphics subsystems, and a
camera module
502978-001
For use only in computer models with AMD processors, UMA graphics subsystems, without
a camera module
502977-001
(2)
Switch cover (includes power button board and cable, volume/LED board, and strip
cover)
487299-001
(3)
Keyboards
Canadian French
486904-121
South Korea
486904-AD1
Taiwan
486904-AB1
Thailand
486904-281
The United States
486904-001
(4)
Top cover (includes TouchPad and cable)
487300-001
(5)
Fan/heat sink assembly (includes thermal material)
For use in computer models with Intel processors
486838-001
For use in computer models with AMD processors with UMA graphics subsystems
492260-001
For use in computer models with AMD processors with discrete graphics subsystems
487355-001
(6)
Speaker assembly
486865-001
(7)
System boards (include thermal material)
For use only in computer models with Intel processors
487274-001
For use only in computer models with AMD processors
(8)
●
Equipped with discrete graphics subsystems
492312-001
●
Equipped with UMA graphics subsystems
492313-001
System fan
486844-001
Plastics Kit (see Plastics Kit on page 25 for more Plastics Kit information)
(9a)
ExpressCard slot bezel
(9b)
Hard drive cover
(9c)
Memory module compartment cover
(10)
Power connector cable (includes power connector and cable)
486864-001
Computer major components
19
Item
Description
Spare part number
(11)
USB board (includes USB board cable)
486842-001
USB board cable
486843-001
(12)
(13)
Modem module (includes modem module cable and RJ-11 connector)
For use in all countries and regions except for Australia and New Zealand
461749-001
For use in Australia and New Zealand
461749-011
Modem module cable (includes RJ-11 connector)
494981-001
WLAN modules
Intel WiFi Link 5100 802.11a/b/g/n WLAN module for use in all countries and regions
480985-001
Intel WiFi Link 5100 802.11a/b/g WLAN module for use in all countries and regions
482957-001
Broadcom 4321 Wi-Fi Adapter for use in Afghanistan, Albania, Algeria, Andorra, Angola,
Antigua & Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the
Bahamas, Bahrain, Bangladesh, Barbados, Belgium, Belize, Benin, Bermuda, Bolivia,
Bosnia & Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina
Faso, Burundi, Cameroon, Cape Verde, the Cayman Islands, the Central African Republic,
Chad, Chile, Colombia, Comoros, the Congo, Costa Rica, Croatia, Cyprus, the Czech
Republic, Denmark, Djibouti, Dominica, the Dominican Republic, East Timor, Ecuador,
Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France,
French Guiana, Gabon, Gambia Georgia, Germany, Ghana, Gibraltar, Greece, Grenada,
Guadeloupe, Guam, Guatemala, Guinea, Guinea-Bissa, Guyana, Haiti, Honduras, Hong
Kong, Hungary, Iceland, India, Ireland, Italy, the Ivory Coast, Jamaica, Jordan, Kenya,
Kiribati, Kyrgyzstan, Laos, Latvia, Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg,
Macedonia, Madagascar, Malawi, the Maldives, Mali, Malta, the Marshall Islands,
Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro,
Morocco, Mozambique, Namibia, Nauru, Nepal, the Netherlands, New Zealand, Nicaragua,
Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay,
the People's Republic of China, Peru, the Philippines, Poland, Portugal, Puerto Rico, the
Republic of Moldova, Romania, Russia, Rwanda, Samoa, San Marino, Sao Tome &
Principe, Saudi Arabia, Senegal, Serbia and Montenegro, the Seychelles, Sierra Leone,
Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa, Spain, Sri
Lanka, St. Kitts & Nevis, St. Lucia, St. Vincent & Grenada, Suriname, Swaziland, Sweden,
Switzerland, Taiwan, Tajikistan, Tanzania, Togo, Tonga, Trinidad & Tobago, Tunisia,
Turkey, Turkmenistan, Tuvalu, Uganda, the United Arab Emirates, the United Kingdom,
Uruguay, Uzbekistan, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
453730-002
Broadcom 4322 802.11a/b/g/n WLAN modules:
20
●
For use in Antigua and Barbuda, Barbados, Belize, Canada, the Cayman Islands,
Guam, Puerto Rico, Trinidad and Tobago, the U.S. Virgin Islands, and the United
States
487330-001
●
For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda,
Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain,
Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia,
Bosnia and Herzegovina, Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria,
Burkina Faso, Burundi, Cameroon, Cape Verde, the Central African Republic, Chad,
Chile, the People's Republic of China, Colombia, Comoros, the Congo, Costa Rica,
Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the Dominican
Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia,
Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia, Germany,
Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea, Guinea-Bissa,
Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy, the
Ivory Coast, Jamaica, Jordan, Kazakhstan, Kenya, Kiribati, Kyrgyzstan, Laos, Latvia,
Lebanon, Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia,
Madagascar, Malawi, Malaysia, the Maldives, Mali, Malta, the Marshall Islands,
Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia,
487330-002
Chapter 3 Illustrated parts catalog
Item
Description
Spare part number
Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles, the
Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan,
Palau, Panama, Papua New Guinea, Paraguay, Peru, the Philippines, Poland,
Portugal, the Republic of Moldova, Romania, Russia, Rwanda, Samoa, San Marino,
Sao Tome and Principe, Saudi Arabia, Senegal, Serbia and Montenegro, the
Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon Islands,
Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia,
St. Vincent and the Grenadines, Suriname, Swaziland, Sweden, Switzerland, Taiwan,
Tajikistan, Tanzania, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey,
Turkmenistan, Tuvalu, Uganda, Ukraine, the United Arab Emirates, the United
Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zaire, Zambia,
and Zimbabwe
Broadcom BCM4312 WLAN b/g module for use in Afghanistan, Albania, Algeria, Andorra,
Angola, Antigua & Barbuda, Argentina, Armenia, Australia, Austria, Azerbaijan, Bahamas,
Bahrain, Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bhutan, Bolivia, Bosnia
& Herzegovina, Botswana, Brazil, Brunei, Bulgaria, Burkina, Faso Burundi, Cambodia,
Cameroon, Cape Verde, Central African Republic, Chad, Zaire, Chile, China, Colombia,
Comoros, Congo, Costa Rica, Croatia, Cyprus, Czech Republic, Denmark, Djibouti,
Dominica, Dominican Republic, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea,
Estonia, Ethiopia, Fiji, Finland, France, Gabon, Gambia, Georgia, Germany, Ghana,
Gibraltar, Greece, Grenada, Guatemala, Guinea, Guinea-Bissau, Guyana, Haiti, Honduras,
Hong Kong, Hungary, Iceland, India, Indonesia, Ireland, Israel, Italy, Ivory Coast, Jamaica,
Japan, Jordan, Kazakhstan, Kenya, Kiribati, Kuwait, Kyrgyzstan, Laos, Latvia, Lebanon,
Lesotho, Liberia, Martinique, British Virgin Islands, French Guiana, Guadeloupe, Nether
Antilles, Aruba, Bermuda, Syria, Liechtenstein, Lithuania, Luxembourg, Macedonia,
Madagascar, Malawi, Malaysia, Maldives, Mali, Malta, Marshall Islands, Mauritania,
Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique,
Namibia, Nauru, Nepal, Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway,
Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Peru, Philippines, Poland,
Portugal, Qatar, Republic of Moldova, Romania, Russia, Rwanda, Samoa, San Marino, Sao
Tome & Principe, Saudi Arabia, Senegal, Serbia and Montenegro, Seychelles, Sierra Leone,
Singapore, Slovakia, Slovenia, Solomon Islands, Somalia, South Africa, South Korea,
Spain, Sri Lanka, St. Kitts & Nevis, St. Lucia, St. Vincent & Grenadines, Suriname,
Swaziland, Sweden, Switzerland, Taiwan, Tajikistan, Tanzania, Thailand, East Timor, Togo,
Tonga, Trinidad & Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda, Ukraine, United
Arab Emirates, United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela, Vietnam,
Yemen, Zambia, and Zimbabwe
(14)
Base enclosure
For use only in computer models with a modem module
492248-001
For use only in computer models without a modem module
487359-001
(15)
RTC battery (includes 2-sided tape)
486835-001
(16)
Audio board (includes audio connectors and audio board cable)
487344-001
Audio board cable kit (not illustrated)
486841-001
(17)
Hard drives (include hard drive bracket)
For use only in computer models with Intel processors:
●
320-GB, 5400-rpm
504781-001
●
250-GB, 5400-rpm
454605-005
●
160-GB, 5400-rpm
454925-005
●
120-GB, 5400-rpm
454924-005
For use in computer models with AMD processors:
Computer major components
21
Item
Description
Spare part number
●
250-GB, 5400-rpm
454605-004
●
160-GB, 5400-rpm
454925-004
●
120-GB, 5400-rpm
454924-004
Hard drive hardware kit (contains screws and hard drive bracket; not illustrated)
(18)
482158-001
Optical drives (include bezel)
For use in computer models with Intel processors:
●
DVD±RW and CD-RW Super Multi, Double-Layer Combo Drive with LightScribe
482178-003
●
DVD±RW and CD-RW Super Multi, Double-Layer Combo Drive
482175-003
●
DVD±RW and CD-RW Combo Drive
487295-001
For use in computer models with AMD processors:
(19)
●
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive with LightScribe
482178-004
●
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive
482175-004
●
DVD±RW and CD-RW Combo Drive
487295-004
Memory modules (1-DIMM)
For use in computer models with Intel processors:
●
2048-MB, 800-MHz, PC2-6400
482169-003
●
1024-MB, 800-MHz, PC2-6400
482168-003
●
512-MB, 800-MHz, PC2-6400
482167-003
●
2048-MB, 667-MHz, PC-5300
448151-004
●
1024-MB, 667-MHz, PC-5300
448150-003
●
512-MB, 667-MHz, PC-5300
452312-003
For use in computer models with AMD processors:
(20)
●
2048-MB, 800-MHz, PC2-6400
482169-004
●
1024-MB, 800-MHz, PC2-6400
482168-004
●
512-MB, 800-MHz, PC2-6400
482167-004
●
2048-MB, 667-MHz, PC-5300
448151-005
●
1024-MB, 667-MHz, PC-5300
448150-004
●
512-MB, 667-MHz, PC-5300
452312-004
Processors (include thermal material)
Intel Core 2 Duo processors:
22
●
T9600 (2.80-GHz, 6-MB L2 cache)
487278-001
●
T9400 (2.53-GHz, 6-MB L2 cache)
487276-001
●
T8600 (2.40-GHz, 3-MB L2 cache)
487275-001
●
T8400 (2.26-GHz, 3-MB L2 cache)
487277-001
Chapter 3 Illustrated parts catalog
Item
Description
Spare part number
●
491832-001
T7350 (2.00-GHz, 3-MB L2 cache)
AMD processors:
(21)
(22)
●
Turion Ultra ZM-86 (2.4-GHz, 2x1-MB L2 cache)
487345-001
●
Turion Ultra ZM-82 (2.2-GHz, 2x1-MB L2 cache)
487346-001
●
Turion Ultra ZM-80 (2.1-GHz, 2x1-MB L2 cache)
487347-001
●
Turion RM-70 2.0-GHz processor (2x512-KB L2 cache)
487348-001
●
Athlon QL-60 1.9-GHz processor (2x512-KB L2 cache)
487349-001
●
Sempron SI-40 2.00-GHz processor (512-KB L2 cache)
487350-001
Bluetooth module
483113-001
Bluetooth module cable (not illustrated)
486868-001
Batteries
●
6-cell, 2.20-Ah, Li-ion for use in computer models with Intel processors
487296-001
●
6-cell, 2.20-Ah, Li-ion for use in computer models with AMD processors
487354-001
Power button board (not illustrated)
492249-001
Rubber Feet Kit (not illustrated)
486863-001
Computer major components
23
Display assembly components
Item
Description
(1)
Display bezels
For use only in computer models with a camera module
487286-001
For use only in computer models without a camera module
487285-001
(2)
Display Hinge Kit
486737-001
(3)
Camera/microphone module
487287-001
(4)
14.1-inch, WXGA, TFT BrightView display panel (includes display panel cable)
For use only with computer models with Intel processors
487279-001
For use only with computer models with AMD processors
487351-001
(5)
Display inverter (includes Mylar shield)
486736-001
(6)
Antenna Kit
(7)
24
Spare part number
For use only with computer models with Intel processors or AMD processors with UMA
graphics subsystems
489066-001
For use only with computer models with AMD processors and discrete graphics subsystems
502979-001
Display enclosure
487284-001
Display cable (not illustrated)
486735-001
Display screw kit (not illustrated; includes screws and rubber screw covers)
486730-001
Rubber display kit (not illustrated)
487283-001
Chapter 3 Illustrated parts catalog
Plastics Kit
Item
Description
Spare part number
Plastics Kit
For use only in computer models with Intel processors
486862-001
For use only in computer models with AMD processors
498322-001
(1)
ExpressCard slot bezel
(2)
Hard drive cover (includes 2 screws)
(3)
Memory module compartment cover (includes 1 screw)
Plastics Kit
25
Mass storage devices
Item
Description
(1)
Hard drives (include hard drive bracket)
Spare part number
For use only in computer models with Intel processors:
●
320-GB, 5400-rpm
504781-001
●
250-GB, 5400-rpm
454605-005
●
160-GB, 5400-rpm
454925-005
●
120-GB, 5400-rpm
454924-005
For use in computer models with AMD processors:
●
250-GB, 5400-rpm
454605-004
●
160-GB, 5400-rpm
454925-004
●
120-GB, 5400-rpm
454924-004
Hard drive hardware kit (contains screws and hard drive bracket; not illustrated)
(2)
482158-001
Optical drives (include bezel)
For use only in computer models with Intel processors:
●
DVD±RW and CD-RW Super Multi, Double-Layer Combo Drive with LightScribe
482178-003
●
DVD±RW and CD-RW Super Multi, Double-Layer Combo Drive
482175-003
●
DVD±RW and CD-RW Combo Drive
487295-001
For use in computer models with AMD processors:
26
●
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive with LightScribe
482178-002
●
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive
482175-004
●
DVD±RW and CD-RW Combo Drive
487295-004
Chapter 3 Illustrated parts catalog
Miscellaneous parts
Description
Spare part number
AC adapters
90-W PFC AC adapter
463955-001
65-W PFC AC adapter
463958-001
System fan
486844-001
Display lid switch module
489862-001
Power cords:
Australia and New Zealand
490371-011
Brazil
490371-201
India
490371-D61
The People's Republic of China
490371-AA1
South Korea
490371-AD1
Taiwan
490371-AB1
The United Kingdom and Hong Kong
490371-031
The United States
490371-001
Screw Kit
487298-001
●
Phillips PM 2.5×4.0 screw
●
Phillips PM 2.5×6.0 captive screw
●
Phillips PM 2.0×2.0 broad head screw
●
Phillips PM 1.5×9.0 screw
●
Phillips PM 2.5×3.0 screw
●
Phillips PM 2.5×17.0 screw
●
Phillips PM 2.5×6.0 screw
●
Phillips PM 2.5×7.0 screw
●
Phillips PM 3.0×4.0 screw
●
Phillips PM 2.0×4.0 screw
●
Phillips PM 2.0×3.0 broad head screw
●
Phillips PM 2.0×10.0 captive screw
Miscellaneous parts
27
Sequential part number listing
28
Spare part
number
Description
448150-003
1024-MB memory module for use only in computer models with Intel processors (667-MHz, PC2-5300, 1DIMM)
448150-004
1024-MB memory module for use only in computer models with AMD processors (667-MHz, PC2-5300, 1DIMM)
448151-004
2048-MB memory module for use only in computer models with Intel processors (667-MHz, PC2-5300, 1DIMM)
448151-005
2048-MB memory module for use only in computer models with AMD processors (667-MHz, PC2-5300, 1DIMM)
452312-003
512-MB memory module for use only in computer models with Intel processors (667-MHz, PC2-5300, 1DIMM)
452312-004
512-MB memory module for use only in computer models with AMD processors (667-MHz, PC2-5300, 1DIMM)
453730-002
Broadcom 4321 Wi-Fi Adapter for use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua & Barbuda,
Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados,
Belgium, Belize, Benin, Bermuda, Bolivia, Bosnia & Herzegovina, Botswana, Brazil, the British Virgin Islands,
Brunei, Bulgaria, Burkina Faso, Burundi, Cameroon, Cape Verde, the Cayman Islands, the Central African
Republic, Chad, Chile, Colombia, Comoros, the Congo, Costa Rica, Croatia, Cyprus, the Czech Republic,
Denmark, Djibouti, Dominica, the Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial
Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia Georgia, Germany,
Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guam, Guatemala, Guinea, Guinea-Bissa, Guyana, Haiti,
Honduras, Hong Kong, Hungary, Iceland, India, Ireland, Italy, the Ivory Coast, Jamaica, Jordan, Kenya,
Kiribati, Kyrgyzstan, Laos, Latvia, Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia,
Madagascar, Malawi, the Maldives, Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius,
Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, the
Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua New
Guinea, Paraguay, the People's Republic of China, Peru, the Philippines, Poland, Portugal, Puerto Rico, the
Republic of Moldova, Romania, Russia, Rwanda, Samoa, San Marino, Sao Tome & Principe, Saudi Arabia,
Senegal, Serbia and Montenegro, the Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon
Islands, Somalia, South Africa, Spain, Sri Lanka, St. Kitts & Nevis, St. Lucia, St. Vincent & Grenada, Suriname,
Swaziland, Sweden, Switzerland, Taiwan, Tajikistan, Tanzania, Togo, Tonga, Trinidad & Tobago, Tunisia,
Turkey, Turkmenistan, Tuvalu, Uganda, the United Arab Emirates, the United Kingdom, Uruguay, Uzbekistan,
Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
454605-004
250-GB, 5400-rpm hard drive for use only in computer models with AMD processors (includes hard drive
bracket)
454605-005
250-GB, 5400-rpm hard drive for use only in computer models with Intel processors (includes hard drive
bracket)
454924-004
120-GB, 5400-rpm hard drive for use only in computer models with AMD processors (includes hard drive
bracket)
454924-005
120-GB, 5400-rpm hard drive for use only in computer models with Intel processors (includes hard drive
bracket)
454925-004
160-GB, 5400-rpm hard drive for use only in computer models with AMD processors (includes hard drive
bracket)
454925-005
160-GB, 5400-rpm hard drive for use only in computer models with Intel processors (includes hard drive
bracket)
459263-002
Broadcom BCM4312 WLAN b/g modules for use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua
& Barbuda, Argentina, Armenia, Australia, Austria, Azerbaijan, Bahamas, Bahrain, Bangladesh, Barbados,
Belarus, Belgium, Belize, Benin, Bhutan, Bolivia, Bosnia & Herzegovina, Botswana, Brazil, Brunei, Bulgaria,
Burkina, Faso Burundi, Cambodia, Cameroon, Cape Verde, Central African Republic, Chad, Chile, People's
Chapter 3 Illustrated parts catalog
Spare part
number
Description
Republic of China, Colombia, Comoros, Congo, Costa Rica, Croatia, Cyprus, Czech Republic, Zaire, Denmark,
Djibouti, Dominica, Dominican Republic, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia,
Ethiopia, Fiji, Finland, France, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada,
Guatemala, Guinea, Guinea-Bissau, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India,
Indonesia, Ireland, Israel, Italy, Ivory Coast, Jamaica, Japan, Jordan, Kazakhstan, Kenya, Kiribati, Kuwait,
Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Martinique, British Virgin Islands, French Guiana,
Guadeloupe, Nether Antilles, Aruba, Bermuda, Syria, Liechtenstein, Lithuania, Luxembourg, Macedonia,
Madagascar, Malawi, Malaysia, Maldives, Mali, Malta, Marshall Islands, Mauritania, Mauritius, Mexico,
Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, Netherlands,
New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea,
Paraguay, Peru, Philippines, Poland, Portugal, Qatar, Republic of Moldova, Romania, Russia, Rwanda,
Samoa, San Marino, Sao Tome & Principe, Saudi Arabia, Senegal, Serbia and Montenegro, Seychelles, Sierra
Leone, Singapore, Slovakia, Slovenia, Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri
Lanka, St. Kitts & Nevis, St. Lucia, St. Vincent & Grenadines, Suriname, Swaziland, Sweden, Switzerland,
Taiwan, Tajikistan, Tanzania, Thailand, East Timor, Togo, Tonga, Trinidad & Tobago, Tunisia, Turkey,
Turkmenistan, Tuvalu, Uganda, Ukraine, United Arab Emirates, United Kingdom, Uruguay, Uzbekistan,
Vanuatu, Venezuela, Vietnam, Yemen, Zambia, and Zimbabwe
461749-001
Modem module for use in all countries and regions except for Australia and New Zealand (includes modem
module cable)
461749-011
Modem module for use only in Australia and New Zealand (includes modem module cable)
463955-001
90-W PFC AC adapter
463958-001
65-W PFC AC adapter
480985-001
Intel WiFi Link 5100 802.11a/b/g/n WLAN module for use in all countries and regions
482158-001
Hard drive hardware kit (contains screws and hard drive bracket)
482167-003
512-MB memory module for use only in computer models with Intel processors (800-MHz, PC2-6400, 1DIMM)
482167-004
512-MB memory module for use only in computer models with AMD processors (800-MHz, PC2-6400, 1DIMM)
482168-003
1024-MB memory module for use only in computer models with Intel processors (800-MHz, PC2-6400, 1DIMM)
482168-004
1024-MB memory module for use only in computer models with AMD processors (800-MHz, PC2-6400, 1DIMM)
482169-003
2048-MB memory module for use only in computer models with Intel processors (800-MHz, PC2-6400, 1DIMM)
482169-004
2048-MB memory module for use only in computer models with AMD processors (800-MHz, PC2-6400, 1DIMM)
482175-003
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive for use only in computer models with Intel
processors (includes bezel)
482175-004
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive for use only in computer models with AMD
processors (includes bezel)
482178-003
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive with LightScribe for use only in computer
models with Intel processors (includes bezel)
482178-004
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive with LightScribe for use only in computer
models with AMD processors (includes bezel)
482957-001
Intel WiFi Link 5100 802.11a/b/g WLAN module for use in all countries and regions
483113-001
Bluetooth module
Sequential part number listing
29
30
Spare part
number
Description
486730-001
Display Screw Kit (includes screws and rubber screw covers)
486736-001
Display inverter (includes Mylar shield and bracket)
486737-001
Display Hinge Kit (includes left and right display hinges and display switch module)
486835-001
RTC battery (includes 2-sided tape)
486838-001
Fan/heat sink assembly for use in computer models with Intel processors (includes thermal material)
486841-001
Audio board cable kit
486842-001
USB board
486843-001
USB board cable
486844-001
System fan
486862-001
Plastics Kit for use only in computer models with Intel processors (see Plastics Kit on page 25) for more
information)
486863-001
Rubber Feet Kit
486864-001
Power connector cable (includes power connector)
486865-001
Speaker assembly
486868-001
Bluetooth module cable for use only in computer models with Intel processors
486904-001
Keyboard for use in the United States
486904-121
Keyboard for use in French Canada
486904-281
Keyboard for use in Thailand
486904-AB1
Keyboard for use in Taiwan
486904-AD1
Keyboard for use in South Korea
487274-001
System board for use only in computer models with Intel processors (includes thermal material)
487275-001
Intel Core Duo T8600 2.40-GHz processor, 3-MB L2 cache; includes thermal material
487276-001
Intel Core Duo T9400 2.53-GHz processor, 6-MB L2 cache; includes thermal material
487277-001
Intel Core Duo T8400 2.26-GHz processor, 3-MB L2 cache; includes thermal material
487278-001
Intel Core Duo T9600 2.80-GHz processor, 6-MB L2 cache; includes thermal material
487279-001
14.1-inch, WXGA, SVA, TFT BrightView display panel for use only in computer models with Intel processors
(includes display panel cable)
487280-001
14.1-inch, WXGA, SVA, TFT BrightView display assembly for use only computer models without a camera
module (includes display panel cable)
487281-001
14.1-inch, WXGA, SVA, TFT BrightView display assembly for use only in computer models with a camera
module (includes display panel cable)
487283-001
Rubber display kit
487284-001
Display enclosure
487285-001
Display bezel for use only in computer models without a camera module
487286-001
Display bezel for use only in computer models with a camera module
Chapter 3 Illustrated parts catalog
Spare part
number
Description
487287-001
Camera/microphone module
487295-001
DVD±RW and CD-RW Combo Drive for use only in computer models with Intel processors
487295-004
DVD±RW and CD-RW Combo Drive for use only in computer models with AMD processors
487296-001
6-cell, 2.20-Ah battery for use only in computer models with Intel processors
487298-001
Screw Kit
487299-001
Switch cover (includes power button board and cable, volume/LED board, and LED cover)
487300-001
Top cover (includes TouchPad and cable)
487330-001
Broadcom 4322 802.11a/b/g/n WLAN module for use in Antigua and Barbuda, Barbados, Belize, Canada, the
Cayman Islands, Guam, Puerto Rico, Trinidad and Tobago, the U.S. Virgin Islands, and the United States
487330-002
Broadcom 4322 802.11a/b/g/n WLAN module for use in Afghanistan, Albania, Algeria, Andorra, Angola,
Antigua and Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain,
Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina,
Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cameroon, Cape Verde,
the Central African Republic, Chad, Chile, the People's Republic of China, Colombia, Comoros, the Congo,
Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the Dominican Republic, East
Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland, France, French
Guiana, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guadeloupe, Guatemala,
Guinea, Guinea-Bissa, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy,
the Ivory Coast, Jamaica, Jordan, Kazakhstan, Kenya, Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho,
Liberia, Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, the Maldives, Mali,
Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia,
Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles, the Netherlands, New
Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama, Papua New Guinea, Paraguay,
Peru, the Philippines, Poland, Portugal, the Republic of Moldova, Romania, Russia, Rwanda, Samoa, San
Marino, Sao Tome and Principe, Saudi Arabia, Senegal, Serbia and Montenegro, the Seychelles, Sierra
Leone, Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri
Lanka, St. Kitts and Nevis, St. Lucia, St. Vincent and the Grenadines, Suriname, Swaziland, Sweden,
Switzerland,
487344-001
Audio board (includes audio connectors and audio board cable)
487345-001
AMD Turion Ultra ZM-86 2.4-GHz processor, 2x1-MB L2 cache; includes thermal material
487346-001
AMD Turion Ultra ZM-82 2.2-GHz processor, 2x1-MB L2 cache; includes thermal material
487347-001
AMD Turion Ultra ZM-80 2.1-GHz processor, 2x1-MB L2 cache; includes thermal material
487348-001
AMD Turion RM-70 2.0-GHz processor, 2x512-KB L2 cache; includes thermal material
487349-001
AMD Athlon QL-60 1.9-GHz processor, 2x512-KB L2 cache; includes thermal material
487350-001
AMD Sempron SI-40 2.0-GHz processor, 256-KB L2 cache; includes thermal material
487351-001
14.1-inch, WXGA, BrightView display panel for use in computer models with AMD processors (includes display
panel cable)
487352-001
14.1-inch, WXGA, BrightView display assembly for use only in computer models with AMD processors,
discrete graphics subsystems, without a camera module
487353-001
14.1-inch, WXGA, BrightView display assembly for use only in computer models with AMD processors,
discrete graphics subsystems, and a camera module
487354-001
6-cell, 2.20-Ah battery for use only in computer models with AMD processors
487355-001
Fan/heat sink assembly for use in computer models with AMD processors with discrete graphics subsystems
(includes thermal material)
Sequential part number listing
31
32
Spare part
number
Description
487359-001
Base enclosure for use only in computer models without a modem module (includes wireless on/off switch)
492248-001
Base enclosure for use only in computer models with a modem module
489066-001
Antenna, microphone cable kit
489862-001
Display lid switch module
490371-001
Power cord for use in the United States
490371-011
Power cord for use in Australia
490371-031
Power cord for use in the United Kingdom
490371-201
Power cord for use in Brazil
490371-AA1
Power cord for use in the People's Republic of China
490371-AB1
Power cord for use in Taiwan
490371-AD1
Power cord for use in South Korea
490371-D61
Power cord for use in India
491832-001
Intel Core Duo T7350 2.00-GHz processor, 3-MB L2 cache; includes thermal material
492249-001
Power button board
492260-001
Fan/heat sink assembly for use in computer models with AMD processors with UMA graphics subsystems
(includes thermal material)
492312-001
System board for use only with computer models with AMD processors that are equipped with UMA graphics
subsystems (includes thermal material)
492313-001
System board for use only with computer models with AMD processors with UMA graphics subsystems
494960-001
Touchpad
494962-001
TouchPad bracket
494965-001
TouchPad button board
494981-001
Modem module cable (includes RJ-11 connector)
498322-001
Plastics kit for use only in computer models with AMD processors (see Plastics Kit on page 25) for more
information)
502977-001
14.1-inch, WXGA, BrightView display assembly for use only in computer models with AMD processors, UMA
graphics subsystems, without a camera module
502978-001
14.1-inch, WXGA, BrightView display assembly for use only in computer models with AMD processors, UMA
graphics subsystems, and a camera module
502979-001
Antenna cable kit for use in computer models with AMD processors and discrete graphics subsystems
504781-001
320-GB, 5400-rpm hard drive for use in computer models with Intel processors (includes hard drive bracket)
Chapter 3 Illustrated parts catalog
4
Removal and replacement procedures
Preliminary replacement requirements
Tools required
You will need the following tools to complete the removal and replacement procedures:
●
Flat-bladed screwdriver
●
Magnetic screwdriver
●
Phillips P0 and P1 screwdrivers
Service considerations
The following sections include some of the considerations that you must keep in mind during
disassembly and assembly procedures.
NOTE: As you remove each subassembly from the computer, place the subassembly (and all
accompanying screws) away from the work area to prevent damage.
Plastic parts
Using excessive force during disassembly and reassembly can damage plastic parts. Use care when
handling the plastic parts. Apply pressure only at the points designated in the maintenance instructions.
Preliminary replacement requirements
33
Cables and connectors
CAUTION: When servicing the computer, be sure that cables are placed in their proper locations
during the reassembly process. Improper cable placement can damage the computer.
Cables must be handled with extreme care to avoid damage. Apply only the tension required to unseat
or seat the cables during removal and insertion. Handle cables by the connector whenever possible. In
all cases, avoid bending, twisting, or tearing cables. Be sure that cables are routed in such a way that
they cannot be caught or snagged by parts being removed or replaced. Handle flex cables with extreme
care; these cables tear easily.
Drive handling
CAUTION: Drives are fragile components that must be handled with care. To prevent damage to the
computer, damage to a drive, or loss of information, observe these precautions:
Before removing or inserting a hard drive, shut down the computer. If you are unsure whether the
computer is off or in Hibernation, turn the computer on, and then shut it down through the operating
system.
Before handling a drive, be sure that you are discharged of static electricity. While handling a drive,
avoid touching the connector.
Before removing a diskette drive or optical drive, be sure that a diskette or disc is not in the drive and
be sure that the optical drive tray is closed.
Handle drives on surfaces covered with at least one inch of shock-proof foam.
Avoid dropping drives from any height onto any surface.
After removing a hard drive, an optical drive, or a diskette drive, place it in a static-proof bag.
Avoid exposing a hard drive to products that have magnetic fields, such as monitors or speakers.
Avoid exposing a drive to temperature extremes or liquids.
If a drive must be mailed, place the drive in a bubble pack mailer or other suitable form of protective
packaging and label the package “FRAGILE.”
34
Chapter 4 Removal and replacement procedures
Grounding guidelines
Electrostatic discharge damage
Electronic components are sensitive to electrostatic discharge (ESD). Circuitry design and structure
determine the degree of sensitivity. Networks built into many integrated circuits provide some protection,
but in many cases, ESD contains enough power to alter device parameters or melt silicon junctions.
A discharge of static electricity from a finger or other conductor can destroy static-sensitive devices or
microcircuitry. Even if the spark is neither felt nor heard, damage may have occurred.
An electronic device exposed to ESD may not be affected at all and can work perfectly throughout a
normal cycle. Or the device may function normally for a while, then degrade in the internal layers,
reducing its life expectancy.
CAUTION: To prevent damage to the computer when you are removing or installing internal
components, observe these precautions:
Keep components in their electrostatic-safe containers until you are ready to install them.
Use nonmagnetic tools.
Before touching an electronic component, discharge static electricity by using the guidelines described
in this section.
Avoid touching pins, leads, and circuitry. Handle electronic components as little as possible.
If you remove a component, place it in an electrostatic-safe container.
The following table shows how humidity affects the electrostatic voltage levels generated by different
activities.
CAUTION:
A product can be degraded by as little as 700 V.
Typical electrostatic voltage levels
Relative humidity
Event
10%
40%
55%
Walking across carpet
35,000 V
15,000 V
7,500 V
Walking across vinyl floor
12,000 V
5,000 V
3,000 V
Motions of bench worker
6,000 V
800 V
400 V
Removing DIPS from plastic tube
2,000 V
700 V
400 V
Removing DIPS from vinyl tray
11,500 V
4,000 V
2,000 V
Removing DIPS from Styrofoam
14,500 V
5,000 V
3,500 V
Removing bubble pack from PCB
26,500 V
20,000 V
7,000 V
Packing PCBs in foam-lined box
21,000 V
11,000 V
5,000 V
Preliminary replacement requirements
35
Packaging and transporting guidelines
Follow these grounding guidelines when packaging and transporting equipment:
●
To avoid hand contact, transport products in static-safe tubes, bags, or boxes.
●
Protect ESD-sensitive parts and assemblies with conductive or approved containers or packaging.
●
Keep ESD-sensitive parts in their containers until the parts arrive at static-free workstations.
●
Place items on a grounded surface before removing items from their containers.
●
Always be properly grounded when touching a component or assembly.
●
Store reusable ESD-sensitive parts from assemblies in protective packaging or nonconductive
foam.
●
Use transporters and conveyors made of antistatic belts and roller bushings. Be sure that
mechanized equipment used for moving materials is wired to ground and that proper materials are
selected to avoid static charging. When grounding is not possible, use an ionizer to dissipate
electric charges.
Workstation guidelines
Follow these grounding workstation guidelines:
36
●
Cover the workstation with approved static-shielding material.
●
Use a wrist strap connected to a properly grounded work surface and use properly grounded tools
and equipment.
●
Use conductive field service tools, such as cutters, screwdrivers, and vacuums.
●
When fixtures must directly contact dissipative surfaces, use fixtures made only of static-safe
materials.
●
Keep the work area free of nonconductive materials, such as ordinary plastic assembly aids and
Styrofoam.
●
Handle ESD-sensitive components, parts, and assemblies by the case or PCM laminate. Handle
these items only at static-free workstations.
●
Avoid contact with pins, leads, or circuitry.
●
Turn off power and input signals before inserting or removing connectors or test equipment.
Chapter 4 Removal and replacement procedures
Equipment guidelines
Grounding equipment must include either a wrist strap or a foot strap at a grounded workstation.
●
When seated, wear a wrist strap connected to a grounded system. Wrist straps are flexible straps
with a minimum of one megohm ±10% resistance in the ground cords. To provide proper ground,
wear a strap snugly against the skin at all times. On grounded mats with banana-plug connectors,
use alligator clips to connect a wrist strap.
●
When standing, use foot straps and a grounded floor mat. Foot straps (heel, toe, or boot straps)
can be used at standing workstations and are compatible with most types of shoes or boots. On
conductive floors or dissipative floor mats, use foot straps on both feet with a minimum of one
megohm resistance between the operator and ground. To be effective, the conductive strips must
be worn in contact with the skin.
The following grounding equipment is recommended to prevent electrostatic damage:
●
Antistatic tape
●
Antistatic smocks, aprons, and sleeve protectors
●
Conductive bins and other assembly or soldering aids
●
Nonconductive foam
●
Conductive tabletop workstations with ground cords of one megohm resistance
●
Static-dissipative tables or floor mats with hard ties to the ground
●
Field service kits
●
Static awareness labels
●
Material-handling packages
●
Nonconductive plastic bags, tubes, or boxes
●
Metal tote boxes
●
Electrostatic voltage levels and protective materials
The following table lists the shielding protection provided by antistatic bags and floor mats.
Material
Use
Voltage protection level
Antistatic plastic
Bags
1,500 V
Carbon-loaded plastic
Floor mats
7,500 V
Metallized laminate
Floor mats
5,000 V
Preliminary replacement requirements
37
Unknown user password
If the computer you are servicing has an unknown user password, follow these steps to clear the
password.
NOTE:
These steps also clear CMOS.
Before disassembling the computer, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 41).
5.
Remove the RTC battery (see RTC battery on page 50).
6.
Wait approximately 5 minutes.
7.
Replace the RTC battery and reassemble the computer.
8.
Connect AC power to the computer. Do not reinsert any batteries at this time.
9.
Turn on the computer.
All passwords and all CMOS settings have been cleared.
38
Chapter 4 Removal and replacement procedures
Component replacement procedures
This chapter provides removal and replacement procedures.
There are as many as 75 screws, in 12 different sizes, that must be removed, replaced, or loosened
when servicing the computer. Make special note of each screw size and location during removal and
replacement.
Serial number
Report the computer serial number to HP when requesting information or ordering spare parts. The
serial number is located on the bottom of the computer.
Component replacement procedures
39
Computer feet
Description
Spare part number
Rubber Feet Kit
486863-001
The computer feet are adhesive-backed rubber pads. The feet attach to the base enclosure in the
locations illustrated below.
40
Chapter 4 Removal and replacement procedures
Battery
Description
Spare part number
6-cell, 2.20-Ah Li-ion battery for use in computer models with Intel processors
487296-001
6-cell, 2.20-Ah Li-ion battery for use in computer models with AMD processors
487354-001
Before disassembling the computer, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
Remove the battery:
1.
Turn the computer upside down on a flat surface.
2.
Slide the battery release latch (1) to release the battery.
3.
Pivot the battery (2) upward and lift it out of the computer (3).
To insert the battery, insert the rear edge of the battery into the battery bay and pivot the front edge
downward until the battery is seated. The battery release latch automatically locks the battery into place.
Component replacement procedures
41
Optical drive
NOTE:
All optical drive spare part kits include an optical drive bezel.
Description
Spare part number
For use in computer models with Intel processors:
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive with LightScribe
482178-003
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive
482175-003
DVD±RW and CD-RW Combo Drive
487295-001
For use in computer models with AMD processors:
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive with LightScribe
482178-004
DVD±RW and CD-RW Super Multi Double-Layer Combo Drive
482175-004
DVD±RW and CD-RW Combo Drive
487295-004
Before removing the optical drive, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 41).
Remove the optical drive:
42
1.
Position the computer with the right side toward you.
2.
Remove the Phillips PM2.5×6.0 screw (1) that secures the optical drive to the computer.
3.
Insert a thin tool, such as a paper clip (2), into the release access. (The optical drive media tray is
partially ejected from the optical drive.)
Chapter 4 Removal and replacement procedures
4.
Use the media tray frame to remove the optical drive (3).
5.
If it is necessary to replace the optical drive bracket, position the optical drive with the optical drive
bracket toward you.
6.
Remove the two Phillips PM2.0×3.0 screws (1) that secure the optical drive bracket to the optical
drive.
7.
Remove the optical drive bracket (2).
Reverse the above procedure to reassemble and install the optical drive.
Component replacement procedures
43
Hard drive
NOTE:
All hard drive spare part kits include a hard drive bracket.
Description
Spare part number
For use in computer models with Intel processors:
320-GB, 5400-rpm
504781-001
250-GB, 5400-rpm
454605-005
160-GB, 5400-rpm
454925-005
120-GB, 5400-rpm
454924-005
For use in computer models with AMD processors:
250-GB, 5400-rpm
454605-004
160-GB, 5400-rpm
454925-004
120-GB, 5400-rpm
454924-004
Hard drive hardware kit (contains screws and hard drive bracket; not illustrated)
482158-001
Before removing the hard drive, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 41).
Remove the hard drive:
44
1.
Position the computer with the front toward you.
2.
Remove the two Phillips PM2.5×6.0 screws (1) that secure the hard drive cover to the computer.
Chapter 4 Removal and replacement procedures
3.
Lift the left side of the hard drive cover (2), swing it to right, and remove the cover (3). The hard
drive cover is included in the Plastics Kit, spare part number 486862-001 for use in computers with
Intel processors and 498322-001 for use in computers with AMD processors.
4.
Remove the three Phillips PM2.0×4.0 screws (1) that secure the hard drive to the computer.
5.
Use the Mylar tab (2) to slide the hard drive (3) until it disconnects from the connector, and then
lift the hard drive up and out of the computer (4).
6.
If it is necessary to replace the hard drive bracket, remove the four Phillips PM3.0×4.0
screws (1) that secure the hard drive bracket to the hard drive.
Component replacement procedures
45
7.
Lift the bracket (2) straight up to remove it from the hard drive.
Reverse this procedure to reassemble and install the hard drive.
46
Chapter 4 Removal and replacement procedures
WLAN module
Description
Spare part number
WLAN modules:
Intel WiFi Link 5100 802.11a/b/g/n WLAN module for use in all countries and regions
480985-001
Intel WiFi Link 5100 802.11a/b/g WLAN module for use in all countries and regions
482957-001
Broadcom 4321 Wi-Fi Adapter for use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua & 453730-002
Barbuda, Argentina, Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain,
Bangladesh, Barbados, Belgium, Belize, Benin, Bermuda, Bolivia, Bosnia & Herzegovina,
Botswana, Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cameroon,
Cape Verde, the Cayman Islands, the Central African Republic, Chad, Chile, Colombia, Comoros,
the Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the
Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia,
Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia Georgia, Germany, Ghana, Gibraltar,
Greece, Grenada, Guadeloupe, Guam, Guatemala, Guinea, Guinea-Bissa, Guyana, Haiti,
Honduras, Hong Kong, Hungary, Iceland, India, Ireland, Italy, the Ivory Coast, Jamaica, Jordan,
Kenya, Kiribati, Kyrgyzstan, Laos, Latvia, Lesotho, Liberia, Liechtenstein, Lithuania, Luxembourg,
Macedonia, Madagascar, Malawi, the Maldives, Mali, Malta, the Marshall Islands, Martinique,
Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique,
Namibia, Nauru, Nepal, the Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman,
Pakistan, Palau, Panama, Papua New Guinea, Paraguay, the People's Republic of China, Peru, the
Philippines, Poland, Portugal, Puerto Rico, the Republic of Moldova, Romania, Russia, Rwanda,
Samoa, San Marino, Sao Tome & Principe, Saudi Arabia, Senegal, Serbia and Montenegro, the
Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon Islands, Somalia, South
Africa, Spain, Sri Lanka, St. Kitts & Nevis, St. Lucia, St. Vincent & Grenada, Suriname, Swaziland,
Sweden, Switzerland, Taiwan, Tajikistan, Tanzania, Togo, Tonga, Trinidad & Tobago, Tunisia,
Turkey, Turkmenistan, Tuvalu, Uganda, the United Arab Emirates, the United Kingdom, Uruguay,
Uzbekistan, Venezuela, Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
Broadcom 4322 802.11a/b/g/n WLAN modules:
For use in Antigua and Barbuda, Barbados, Belize, Canada, the Cayman Islands, Guam, Puerto
Rico, Trinidad and Tobago, the U.S. Virgin Islands, and the United States
487330-001
For use in Afghanistan, Albania, Algeria, Andorra, Angola, Antigua and Barbuda, Argentina,
Armenia, Aruba, Australia, Austria, Azerbaijan, the Bahamas, Bahrain, Bangladesh, Barbados,
Belarus, Belgium, Belize, Benin, Bermuda, Bhutan, Bolivia, Bosnia and Herzegovina, Botswana,
Brazil, the British Virgin Islands, Brunei, Bulgaria, Burkina Faso, Burundi, Cameroon, Cape Verde,
the Central African Republic, Chad, Chile, the People's Republic of China, Colombia, Comoros, the
Congo, Costa Rica, Croatia, Cyprus, the Czech Republic, Denmark, Djibouti, Dominica, the
Dominican Republic, East Timor, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia,
Ethiopia, Fiji, Finland, France, French Guiana, Gabon, Gambia, Georgia, Germany, Ghana,
Gibraltar, Greece, Grenada, Guadeloupe, Guatemala, Guinea, Guinea-Bissa, Guyana, Haiti,
Honduras, Hong Kong, Hungary, Iceland, India, Ireland, Israel, Italy, the Ivory Coast, Jamaica,
Jordan, Kazakhstan, Kenya, Kiribati, Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia,
Liechtenstein, Lithuania, Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, the Maldives,
Mali, Malta, the Marshall Islands, Martinique, Mauritania, Mauritius, Mexico, Micronesia, Monaco,
Mongolia, Montenegro, Morocco, Mozambique, Namibia, Nauru, Nepal, the Nether Antilles, the
Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman, Pakistan, Palau, Panama,
Papua New Guinea, Paraguay, Peru, the Philippines, Poland, Portugal, the Republic of Moldova,
Romania, Russia, Rwanda, Samoa, San Marino, Sao Tome and Principe, Saudi Arabia, Senegal,
Serbia and Montenegro, the Seychelles, Sierra Leone, Singapore, Slovakia, Slovenia, the Solomon
Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts and Nevis, St. Lucia, St.
Vincent and the Grenadines, Suriname, Swaziland, Sweden, Switzerland, Taiwan, Tajikistan,
Tanzania, Togo, Tonga, Trinidad and Tobago, Tunisia, Turkey, Turkmenistan, Tuvalu, Uganda,
Ukraine, the United Arab Emirates, the United Kingdom, Uruguay, Uzbekistan, Vanuatu, Venezuela,
Vietnam, Yemen, Zaire, Zambia, and Zimbabwe
487330-002
Broadcom BCM4312 WLAN b/g module for use in Afghanistan, Albania, Algeria, Andorra, Angola,
Antigua & Barbuda, Argentina, Armenia, Australia, Austria, Azerbaijan, Bahamas, Bahrain,
Bangladesh, Barbados, Belarus, Belgium, Belize, Benin, Bhutan, Bolivia, Bosnia & Herzegovina,
459263-002
Component replacement procedures
47
Description
Spare part number
Botswana, Brazil, Brunei, Bulgaria, Burkina, Faso Burundi, Cambodia, Cameroon, Cape Verde,
Central African Republic, Chad, Chile, People's Republic of China, Colombia, Comoros, Congo,
Costa Rica, Croatia, Cyprus, Czech Republic, Zaire, Denmark, Djibouti, Dominica, Dominican
Republic, Ecuador, Egypt, El Salvador, Equitorial Guinea, Eritrea, Estonia, Ethiopia, Fiji, Finland,
France, Gabon, Gambia, Georgia, Germany, Ghana, Gibraltar, Greece, Grenada, Guatemala,
Guinea, Guinea-Bissau, Guyana, Haiti, Honduras, Hong Kong, Hungary, Iceland, India, Indonesia,
Ireland, Israel, Italy, Ivory Coast, Jamaica, Japan, Jordan, Kazakhstan, Kenya, Kiribati, Kuwait,
Kyrgyzstan, Laos, Latvia, Lebanon, Lesotho, Liberia, Martinique, British Virgin Islands, French
Guiana, Guadeloupe, Nether Antilles, Aruba, Bermuda, Syria, Liechtenstein, Lithuania,
Luxembourg, Macedonia, Madagascar, Malawi, Malaysia, Maldives, Mali, Malta, Marshall Islands,
Mauritania, Mauritius, Mexico, Micronesia, Monaco, Mongolia, Montenegro, Morocco, Mozambique,
Namibia, Nauru, Nepal, Netherlands, New Zealand, Nicaragua, Niger, Nigeria, Norway, Oman,
Pakistan, Palau, Panama, Papua New Guinea, Paraguay, Peru, Philippines, Poland, Portugal,
Qatar, Republic of Moldova, Romania, Russia, Rwanda, Samoa, San Marino, Sao Tome & Principe,
Saudi Arabia, Senegal, Serbia and Montenegro, Seychelles, Sierra Leone, Singapore, Slovakia,
Slovenia, Solomon Islands, Somalia, South Africa, South Korea, Spain, Sri Lanka, St. Kitts & Nevis,
St. Lucia, St. Vincent & Grenadines,. Suriname, Swaziland, Sweden, Switzerland, Taiwan,
Tajikistan, Tanzania, Thailand, East Timor, Togo, Tonga, Trinidad & Tobago, Tunisia, Turkey,
Turkmenistan, Tuvalu, Uganda, Ukraine, United Arab Emirates, United Kingdom, Uruguay,
Uzbekistan, Vanuatu, Venezuela, Vietnam, Yemen, Zambia, and Zimbabwe
Before removing the WLAN module, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 41).
5.
Remove the hard drive cover (see Hard drive on page 44).
Remove the WLAN module:
48
1.
Position the computer with the front toward you.
2.
Disconnect the two WLAN antenna cables (1) from the WLAN module.
3.
Remove the two Phillips PM2.0×3.0 screws (2) that secure the WLAN module to the computer.
(The edge of the module opposite the slot rises away from the computer.)
Chapter 4 Removal and replacement procedures
4.
Remove the WLAN module (3) by pulling it away from the slot at an angle.
CAUTION: To prevent an unresponsive system, replace the wireless module only with a wireless
module authorized for use in the computer by the governmental agency that regulates wireless
devices in your country or region. If you replace the module and then receive a warning message,
remove the module to restore computer functionality, and then contact technical support through
Help and Support.
NOTE: WLAN modules are designed with a notch (4) to prevent incorrect insertion into the WLAN
module slot.
Reverse this procedure to install a WLAN module.
Component replacement procedures
49
RTC battery
NOTE: Removing the RTC battery and leaving it uninstalled for 5 or more minutes causes all
passwords and CMOS settings to be cleared.
Description
Spare part number
RTC battery (includes 2-sided tape)
486835-001
Before removing the RTC battery, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 41).
Remove the RTC battery:
50
1.
Remove the two Phillips PM2.5×6.0 screws (1) that secure the Mini Card compartment cover to
the computer.
2.
Lift the right side of the cover (2), swing it to left, and remove the cover (3).
3.
Disconnect the RTC battery cable (1) from the system board.
Chapter 4 Removal and replacement procedures
4.
Remove the RTC battery (2).
Reverse this procedure to install the RTC battery.
Component replacement procedures
51
Memory module
Description
Spare part number
For use in computer models with Intel processors:
2048-MB (800-MHz, PC2-6400, 1-DIMM)
482169-003
1024-MB (800-MHz, PC2-6400, 1-DIMM)
482168-003
512-MB (800-MHz, PC2-6400, 1-DIMM)
482167-003
2048-MB (667-MHz, PC2-5300, 1-DIMM)
448151-004
1024-MB (667-MHz, PC2-5300, 1-DIMM)
448150-003
512-MB (667-MHz, PC2-5300, 1-DIMM)
452312-003
For use in computer models with AMD processors:
2048-MB (800-MHz, PC2-6400, 1-DIMM)
482169-004
1024-MB (800-MHz, PC2-6400, 1-DIMM)
482168-004
512-MB (800-MHz, PC2-6400, 1-DIMM)
482167-004
2048-MB (667-MHz, PC2-5300, 1-DIMM)
448151-005
1024-MB (667-MHz, PC2-5300, 1-DIMM)
448150-004
512-MB (667-MHz, PC2-5300, 1-DIMM)
452312-004
Before removing the memory module, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 41).
Remove the memory module:
52
1.
Position the computer with the front toward you.
2.
Loosen the Phillips PM2.5×6.0 captive screw (1) that secures the memory module compartment
cover to the computer.
Chapter 4 Removal and replacement procedures
3.
Lift the right side of the cover (2), swing it to the left, and lift the cover off the computer (3). The
memory module compartment cover is included in the Plastics Kit, spare part number 486862-001
for use in computers with Intel processors and 498322-001 for use in computers with AMD
processors.
4.
Spread the retaining tabs (1) on each side of the memory module slot to release the memory
module. (The edge of the module opposite the slot rises away from the computer.)
5.
Remove the module (2) by pulling it away from the slot at an angle.
NOTE: Memory modules are designed with a notch (3) to prevent incorrect insertion into the
memory module slot.
Reverse this procedure to install a memory module.
Component replacement procedures
53
Keyboard
For use in:
Spare part number
For use in:
Spare part number
Canadian French
486904-121
Thailand
486904-281
South Korea
486904-AD1
The United States
486904-001
Taiwan
486904-AB1
Before removing the keyboard, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 41).
5.
Remove the Mini Card compartment cover (see RTC battery on page 50).
Remove the keyboard:
54
1.
Turn the computer upside down, with the front toward you.
2.
Remove the three Phillips PM2.5×17.0 screws that secure the keyboard to the computer.
3.
Turn the computer display-side up, with the front toward you.
4.
Open the computer as far as possible.
5.
Release the top edge of the keyboard by lifting it up to disengage the keyboard from the tabs on
the switch cover.
6.
Lift the top edge of the keyboard until it rests at an angle (1).
Chapter 4 Removal and replacement procedures
7.
Lift the keyboard (2) up until the tabs on the bottom of the keyboard are clear of the switch cover.
8.
Release the zero insertion force (ZIF) connector (1) to which the keyboard cable is attached and
disconnect the keyboard cable (2) from the system board.
9.
Remove the keyboard.
Reverse this procedure to install the keyboard.
Component replacement procedures
55
Switch cover
Description
Spare part number
Switch cover (includes power button board and cable, volume/LED board, and LED cover)
487299-001
Before removing the switch cover, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the following components:
a.
Battery (see Battery on page 41).
b.
Optical drive (see Optical drive on page 42).
c.
Keyboard (see Keyboard on page 54).
Remove the switch cover:
56
1.
Turn the computer upside down, with the rear toward you.
2.
Remove the two Phillips PM2.5×10.0 screws (1), the Phillips PM2.0x2.0 broad head screw (2) from
the optical drive bay, and the four Phillips PM2.0x4.0 screws (3) from the battery bay that secure
the switch cover to the computer.
3.
Turn the computer display-side up, with the front toward you.
4.
Open the computer as far as possible.
5.
Release the ZIF connector to which the power button board cable (1) is connected and disconnect
the cable from the system board.
Chapter 4 Removal and replacement procedures
6.
Release the ZIF connector to which the volume board cable (2) is connected and disconnect the
cable from the system board.
7.
Lift the front edge of the switch cover to disengage it from the computer, pull the switch cover toward
the display until the light pipe on the front of the switch cover clears the top cover, and then lift the
cover up and out of the computer (3).
Reverse this procedure to install the switch cover.
Component replacement procedures
57
Speaker assembly
Description
Spare part number
Speaker assembly
486865-001
Before removing the speaker assembly, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 41).
5.
Remove the following components:
a.
Optical drive (see Optical drive on page 42)
b.
Keyboard (see Keyboard on page 54)
c.
Switch cover (see Switch cover on page 56)
Remove the speaker assembly:
58
1.
Disconnect the speaker cable (1) from the system board.
2.
Disconnect the num lock cable (2) from the system board.
3.
Remove the two Phillips PM2.5×4.0 screws (1) that secure the speaker assembly to the computer.
Chapter 4 Removal and replacement procedures
4.
Lift the speaker assembly (2) straight up to remove it from the computer.
Reverse this procedure to install the speaker assembly.
Component replacement procedures
59
Display assembly
Description
Spare part number
14.1-inch, WXGA, BrightView display assembly for use only in computer models Intel processors
with a camera module (includes microphones)
487281-001
14.1-inch, WXGA, BrightView display assembly for use only in computer models with Intel
processors without a camera module (includes microphones)
487280-001
14.1-inch, WXGA, BrightView display assembly for use only in computer models with AMD
processors, discrete graphics subsystems, and a camera module
487353-001
14.1-inch, WXGA, BrightView display assembly for use only in computer models with AMD
processors, discrete graphics subsystems, without a camera module
487352-001
14.1-inch, WXGA, BrightView display assembly for use only in computer models with AMD
processors, UMA graphics subsystems, and a camera module
502978-001
14.1-inch, WXGA, BrightView display assembly for use only in computer models with AMD
processors, UMA graphics subsystems, without a camera module
502977-001
Before removing the display assembly, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 41).
5.
Disconnect the wireless antenna cables from the WLAN module (see WLAN module on page 47).
6.
Remove the following components:
a.
Keyboard (see Keyboard on page 54)
b.
Optical drive (see Optical drive on page 42)
c.
Switch cover (see Switch cover on page 56)
Remove the display assembly:
60
1.
Turn the computer display-side up, with the front toward you.
2.
Open the display as far as possible.
3.
Remove the wireless antenna cables (1) from the hole in the system board and the routing channels
built into the top cover.
Chapter 4 Removal and replacement procedures
4.
Disconnect the display panel cable (2).
CAUTION: Support the display assembly when removing the following screws. Failure to support
the display assembly can result in damage to the display assembly and other computer
components.
5.
Remove the four black Phillips PM2.5×6.0 screws (1) that secure the display assembly to the
computer.
6.
Remove the display assembly (2).
Component replacement procedures
61
7.
If it is necessary to replace any of the display assembly internal components, remove the following
screw covers and screws. The display rubber screw covers are included in the Rubber Display Kit,
spare part number 487283-001.
(1) Two rubber screw covers on the display bezel bottom edge
(2) Two Phillips PM2.5×6.0 screws
8.
Flex the top side (1), the left and right sides (2), and the bottom (3) of the display bezel until the
bezel disengages from the display enclosure.
9.
Remove the display bezel (4). The display bezel is available using spare part number 487286-001
for computers with a camera module, 487285-001 for computers without a camera module.
10. If it is necessary to replace the inverter, release the inverter (1) from the clips in the display
enclosure as far as the display panel cable and the backlight cable will allow.
62
Chapter 4 Removal and replacement procedures
11. Disconnect the display panel cable (2) and the backlight cable (3) from the display inverter. The
display inverter is available using spare part number 486736-001.
12. Remove the inverter.
13. If it is necessary to replace the display panel, remove the six black Phillips PM2.5×5.0 screws (1)
that secure the display panel to the display enclosure, and then lift the panel from the enclosure
(2). The display panel is available using the spare part number 487279-001 for computers with
Intel processors, 487351-001 for computers with AMD processors.
14. If it is necessary to replace the display cable, follow these steps:
a.
Peel back the plastic that covers the cable (1).
b.
Remove the tape that secures the cable to the display (2).
c.
Unplug the cable from the display (3).
d.
Remove the cable from the display (4).
Component replacement procedures
63
The display cable is available using spare part number 486735-001.
15. If it is necessary to replace the display hinges, remove the four silver Phillips PM2.0×3.0 screws
(1) that secure each hinge to the display.
16. Remove the display hinges (2) from the display. The display hinges are available using spare part
number 486737-001.
17. If it is necessary to replace the wireless antenna transceivers and cables, remove the Phillips
PM2.5×4.0 screw (1) that secures each transceiver to the display enclosure.
18. Detach the wireless antenna transceivers (2) from the display enclosure.
19. Remove the wireless antenna cables from the clips (3) built into the display enclosure.
64
Chapter 4 Removal and replacement procedures
20. Remove the wireless antenna transceivers and cables (4) from the display enclosure. The wireless
antenna transceivers and cables are included in the Wireless Antenna Kit, spare part number
489066-001 for computers with Intel processors or AMD processors with UMA graphics, and
502979-001 for use in computer models with AMD processors and discrete graphics.
Reverse this procedure to reassemble and install the display assembly.
Camera/microphone module
If it has been determined that the camera/microphone module is the component that must be replaced
to complete the computer repair, the display assembly does not have to be removed. Follow the
procedures in this section to replace the camera module. For information on replacing the display
assembly and other display assembly internal components, see Display assembly on page 60.
Description
Spare part number
Camera/microphone module
487287-001
Before removing the camera/microphone module, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 41).
Remove the camera/microphone module:
1.
Turn the computer display-side up, with the front toward you.
2.
Open the computer as far as it will open.
3.
Flex the inside edges of the left and right sides, and then pull outward on the middle of the top
edge (1) of the display bezel until the top middle of the bezel disengages from the display enclosure.
Component replacement procedures
65
4.
Pull outward on the left and right of the top edge (2) of the display bezel until the bezel disengages
from the display enclosure.
5.
Release the display bezel top edge (3).
6.
Release the camera module assembly (1) from the display enclosure as far as the camera/
microphone module cable allows.
7.
Disconnect the camera module cable (2) from the camera/microphone module.
8.
Remove the camera/microphone module from the computer.
Reverse this procedure to install the camera/microphone module.
66
Chapter 4 Removal and replacement procedures
Top cover
Description
Spare part number
Top cover (includes TouchPad and cable)
487300-001
Before removing the top cover, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 41).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 44)
b.
Optical drive (see Optical drive on page 42)
c.
Keyboard (see Keyboard on page 54)
d.
Switch cover (see Switch cover on page 56)
e.
Speaker assembly (see Speaker assembly on page 58)
f.
Display assembly (see Display assembly on page 60)
Remove the top cover:
1.
Turn the computer upside down, with the front toward you.
2.
Remove the seven screws that secure the top cover to the computer.
●
(1) Three Phillips PM2.5×10.0 screws
●
(2) Two Phillips PM2.5×5.0 screws
●
(3) Two Phillips PM2.0×3.0 screws
Component replacement procedures
67
68
3.
Turn the computer right-side up, with the front toward you.
4.
Disconnect the following cables from the system board:
●
Bluetooth module cable (1)
●
TouchPad cable (2)
●
USB board cable (3) and release from top cover clips (4)
●
Num lock light cable (5)
5.
Remove the two Phillips PM2.5×7.0 screws (1) that secure the top cover to the computer.
6.
Lift up the rear edge of the top cover until it releases from the base (2).
Chapter 4 Removal and replacement procedures
7.
Remove the top cover (3).
Reverse this procedure to install the top cover.
Component replacement procedures
69
TouchPad button board
Description
Spare part number
TouchPad bracket
494962-001
TouchPad button board
494965-001
Before removing the TouchPad button board, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 41).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 44)
b.
Optical drive (see Optical drive on page 42)
c.
Keyboard (see Keyboard on page 54)
d.
Switch cover (see Switch cover on page 56)
e.
Speaker assembly (see Speaker assembly on page 58)
f.
Display assembly (see Display assembly on page 60)
g.
Top cover (see Top cover on page 67)
Remove the TouchPad button board:
70
1.
Turn the top cover upside down with the front toward you.
2.
Remove the four Phillips PM2.5×3.0 screws (1) that secure the TouchPad assembly to the top
cover.
3.
Remove the TouchPad bracket (2) from the top cover.
Chapter 4 Removal and replacement procedures
4.
Remove the TouchPad button board (3) from the TouchPad bracket.
Reverse the above procedure to reassemble and install the TouchPad button board.
Bluetooth module
Description
Spare part number
Bluetooth module
483113-001
Before removing the Bluetooth module, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 41).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 44)
b.
Optical drive (see Optical drive on page 42)
c.
Keyboard (see Keyboard on page 54)
d.
Switch cover (see Switch cover on page 56)
e.
Speaker assembly (see Speaker assembly on page 58)
f.
Display assembly (see Display assembly on page 60)
g.
Top cover (see Top cover on page 67)
Remove the Bluetooth module:
Component replacement procedures
71
1.
Turn the top cover upside down with the front toward you.
2.
Disconnect the Bluetooth module cable (1) from the system board.
3.
Remove the two silver PM2.0x3.0 screws (2) that secure the Bluetooth module to the top cover.
4.
Remove the Bluetooth module (3) from the top cover.
Reverse the above procedure to install the Bluetooth module.
72
Chapter 4 Removal and replacement procedures
Modem module
Description
Spare part number
Modem module for use in all countries and regions except for Australia and New Zealand (includes
modem module cable)
461749-001
Modem module for use only in Australia and New Zealand (includes modem module cable)
461749-011
Modem module cable (includes RJ-11 connector)
494981-001
Before removing the modem module, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 41).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 44)
b.
Optical drive (see Optical drive on page 42)
c.
Keyboard (see Keyboard on page 54)
d.
Switch cover (see Switch cover on page 56)
e.
Speaker assembly (see Speaker assembly on page 58)
f.
Display assembly (see Display assembly on page 60)
g.
Top cover (see Top cover on page 67)
Remove the modem module:
1.
Turn the computer upright with the front toward you.
2.
Disconnect the modem module cable (1) from the modem module.
3.
Remove the two Phillips PM2.0×3.0 screws (2) that secure the modem module to the system board.
Component replacement procedures
73
4.
Lift up on the front of the modem module (3) to disconnect it from the system board.
5.
Remove the modem module.
Reverse the above procedure to install the modem module, and be sure that the connector on the bottom
of the modem module connects firmly into the system board.
Audio board
Description
Spare part number
Audio board (includes audio connectors and audio board cable)
487344-001
Before removing the audio board, follow these steps:
74
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 41).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 44)
b.
Optical drive (see Optical drive on page 42)
c.
Keyboard (see Keyboard on page 54)
d.
Switch cover (see Switch cover on page 56)
e.
Speaker assembly (see Speaker assembly on page 58)
f.
Display assembly (see Display assembly on page 60)
g.
Top cover (see Top cover on page 67)
Chapter 4 Removal and replacement procedures
Remove the audio board:
1.
Turn the computer upright with the front toward you.
2.
Disconnect the audio board cable (1) from the system board.
3.
Remove the cable from between the components that secure it in the base (2).
4.
Remove the two Phillips PM2.5×3.0 screws (3) that secure the audio board to the computer.
5.
Lift the rear edge of the audio board and swing it forward until the audio connectors disengage
from the base enclosure.
6.
Remove the audio board (4).
Reverse the above procedure to install the audio board.
USB board
Description
Spare part number
USB board
486842-001
USB board cable
486843-001
Before removing the USB board, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
Component replacement procedures
75
4.
Remove the battery (see Battery on page 41).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 44)
b.
Optical drive (see Optical drive on page 42)
c.
Keyboard (see Keyboard on page 54)
d.
Switch cover (see Switch cover on page 56)
e.
Speaker assembly (see Speaker assembly on page 58)
f.
Display assembly (see Display assembly on page 60)
g.
Top cover (see Top cover on page 67)
Remove the USB board:
1.
Turn the computer upright with the right side toward you.
2.
Disconnect the USB board cable (1) from the system board. The USB board cable is available as
spare part number 486842-001.
3.
Remove the cable from the base enclosure clips (2).
4.
Remove the Phillips PM2.5×4.0 screw (3) that secures the USB board to the computer.
5.
Lift the USB board (4) straight up to remove it from the computer.
Reverse this procedure to install the USB board.
76
Chapter 4 Removal and replacement procedures
Power connector cable
Description
Spare part number
Power connector cable (includes power connector)
486864-001
Before removing the power connector cable, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 41).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 44)
b.
Optical drive (see Optical drive on page 42)
c.
Keyboard (see Keyboard on page 54)
d.
Switch cover (see Switch cover on page 56)
e.
Speaker assembly (see Speaker assembly on page 58)
f.
Display assembly (see Display assembly on page 60)
g.
Top cover (see Top cover on page 67)
Remove the power connector cable:
1.
Turn the computer upright with the right side toward you.
2.
Disconnect the power connector cable (1) from the system board.
3.
Remove the power connector (2) from the clip built into the base enclosure.
Component replacement procedures
77
4.
Remove the cable from the base enclosure clips (3).
Reverse this procedure to install the power connector cable.
78
Chapter 4 Removal and replacement procedures
System board
Description
Spare part number
System board for use only in computer models with Intel processors (includes thermal material)
487274-001
System board for use only in computer models with AMD processors and discrete graphics
subsystems (includes thermal material)
492312-001
System board for use only in computer models with AMD processors and UMA graphics subsystems
(includes thermal material)
492313-001
When replacing the system board, be sure that the following components are removed from the defective
system board and installed on the replacement system board:
●
RTC battery (see RTC battery on page 50)
●
Memory modules (see Memory module on page 52)
●
WLAN module (see WLAN module on page 47)
●
Modem module (see Modem module on page 73)
Before removing the system board, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 41).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 44)
b.
Optical drive (see Optical drive on page 42)
c.
Keyboard (see Keyboard on page 54)
d.
Switch cover (see Switch cover on page 56)
e.
Speaker assembly (see Speaker assembly on page 58)
f.
Display assembly (see Display assembly on page 60)
g.
Top cover (see Top cover on page 67)
Remove the system board:
1.
Turn the computer upright with the right side toward you.
Component replacement procedures
79
2.
80
Disconnect the following cables from the system board (if still connected):
●
(1) Modem cable
●
(2) Audio board cable
●
(3) Fan cable
3.
Remove the two silver captive Phillips PM1.5×9.0 screws on the expansion port connector (1).
4.
Remove the two black Phillips PM2.5×6.0 screws that secure the system board to the computer
(2).
5.
Lift the right side of the system board (1) until it rests at an angle (2).
Chapter 4 Removal and replacement procedures
6.
Release the system board by sliding it to the right at an angle (3) until the connectors on the left
side of the system board disengage from the base enclosure, and then remove the system board.
7.
If it is necessary to replace the modem module cable, remove the RJ-11 connector (1) from the
clip built into the base enclosure.
8.
Remove the modem module cable (2) from the routing channel built into the base enclosure. The
modem module cable is available using spare part number 494981-001.
When replacing the system board, be sure that the following components are removed from the defective
system board and installed on the replacement system board:
●
Fan/heat sink assembly (see Fan/heat sink assembly on page 82)
●
Processor (see Processor on page 85)
Reverse the preceding procedure to install the system board.
Component replacement procedures
81
Fan/heat sink assembly
Description
Spare part number
Fan/heat sink assembly for use in computer models with Intel processors (includes thermal material)
486838-001
Fan/heat sink assembly for use in computer models with AMD processors and UMA graphics
subsystems (includes thermal material)
492260-001
Fan/heat sink assembly for use in computer models and AMD processors with discrete graphics
subsystems (includes thermal material)
487355-001
NOTE: To properly ventilate the computer, allow at least a 7.6-cm (3-inch) clearance on the right side
and rear panel of the computer. The computer uses an electric fan for ventilation. The fan is controlled
by a temperature sensor and is designed to turn on automatically when high temperature conditions
exist. These conditions are affected by high external temperatures, system power consumption, power
management/battery conservation configurations, battery fast charging, and software requirements.
Exhaust air is displaced through the ventilation grill located on the left side of the computer.
Before removing the fan/heat sink assembly, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 41).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 44)
b.
Optical drive (see Optical drive on page 42)
c.
Keyboard (see Keyboard on page 54)
d.
Switch cover (see Switch cover on page 56)
e.
Speaker assembly (see Speaker assembly on page 58)
f.
Display assembly (see Display assembly on page 60)
g.
Top cover (see Top cover on page 67)
h.
System board (see System board on page 79)
Remove the fan/heat assembly (fan/heat sink appearance may vary):
1.
Turn the system board upside down with the external monitor port toward you.
2.
Loosen the four Phillips PM2.0×10.0 captive screws (1) that secure the fan/heat sink assembly to
the system board.
NOTE: Due to the adhesive quality of the thermal material located between the fan/heat sink
assembly and system board components, it may be necessary to move the fan/heat sink assembly
from side to side to detach the assembly.
82
Chapter 4 Removal and replacement procedures
3.
Remove the fan/heat sink assembly (2).
The thermal material must be thoroughly cleaned from the surface of the fan/heat sink assembly (1) and
the processor (2) each time the fan/heat sink assembly is removed. Thermal pads and thermal paste
must be installed on all surfaces before the fan/heat sink assembly is reinstalled.
The following locations require thermal pads on systems with discrete graphics subsystems:
●
(3) Four locations on heat sink
●
(4) Northbridge chip
●
(5) NVIDIA video chip
●
(6) Capacitors
NOTE: Thermal pads and thermal paste are included with all fan/heat sink assembly, system board,
and processor spare part kits.
The thermal material must be thoroughly cleaned from the surface of the fan/heat sink assembly (1) and
the processor (2) each time the fan/heat sink assembly is removed. Thermal pads and thermal paste
must be installed on all surfaces before the fan/heat sink assembly is reinstalled.
Component replacement procedures
83
The following locations require thermal pads on systems with UMA graphics subsystems:
●
(3) Four locations on heat sink
●
(4) Capacitors
●
(5) Northbridge chip
Reverse this procedure to install the fan/heat sink assembly.
84
Chapter 4 Removal and replacement procedures
Processor
NOTE:
All processor spare part kits include thermal material.
Description
Spare part number
Intel Core Duo processors:
T9600 (2.80-GHz, 6-MB L2 cache)
487278-001
T9400 (2.53-GHz, 6-MB L2 cache)
487276-001
T8600 (2.40-GHz, 3-MB L2 cache)
487275-001
T8400 (2.26-GHz, 3-MB L2 cache)
487277-001
T7350 (2.00-GHz, 3-MB L2 cache)
491832-001
AMD processors:
Turion Ultra ZM-86 2.4-GHz processor (2x1-MB L2 cache)
487345-001
Turion Ultra ZM-82 2.2-GHz processor (2x1-MB L2 cache)
487346-001
Turion Ultra ZM-80 2.1-GHz processor (2x1-MB L2 cache)
487347-001
Turion RM-70 2.0-GHz processor (2x512-KB L2 cache)
487348-001
Athlon QL-60 1.9-GHz processor (2x512-KB L2 cache)
487349-001
Sempron SI-40 2.00-GHz processor (512-KB L2 cache)
487350-001
Before removing the processor, follow these steps:
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 41).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 44)
b.
Optical drive (see Optical drive on page 42)
c.
Keyboard (see Keyboard on page 54)
d.
Switch cover (see Switch cover on page 56)
e.
Speaker assembly (see Speaker assembly on page 58)
f.
Display assembly (see Display assembly on page 60)
g.
Top cover (see Top cover on page 67)
Component replacement procedures
85
h.
System board (see System board on page 79)
i.
Fan/heat sink assembly (see Fan/heat sink assembly on page 82)
Remove the processor:
1.
Turn the processor locking screw (1) one-half turn counterclockwise until you hear a click.
2.
Lift the processor (2) straight up and remove it.
NOTE: The gold triangle (3) on the processor must be aligned with the triangle icon (4) embossed
on the processor socket when you install the processor.
Reverse this procedure to install the processor.
System fan
Description
Spare part number
System fan
486844-001
Before removing the system fan, follow these steps:
86
1.
Shut down the computer. If you are unsure whether the computer is off or in Hibernation, turn the
computer on, and then shut it down through the operating system.
2.
Disconnect all external devices connected to the computer.
3.
Disconnect the power from the computer by first unplugging the power cord from the AC outlet and
then unplugging the AC adapter from the computer.
4.
Remove the battery (see Battery on page 41).
5.
Remove the following components:
a.
Hard drive (see Hard drive on page 44)
b.
Optical drive (see Optical drive on page 42)
c.
Keyboard (see Keyboard on page 54)
Chapter 4 Removal and replacement procedures
d.
Switch cover (see Switch cover on page 56)
e.
Speaker assembly (see Speaker assembly on page 58)
f.
Display assembly (see Display assembly on page 60)
g.
Top cover (see Top cover on page 67)
h.
System board (see System board on page 79)
Remove the system fan:
1.
Position the base enclosure with the front toward you.
2.
Remove the two black Phillips PM2.5×6.0 screws (1) that secure the system fan to the
computer.
3.
Lift the system fan from the base enclosure (2).
Reverse this procedure to install a system fan.
Component replacement procedures
87
5
Setup Utility
WARNING! Only authorized technicians trained by HP must repair this equipment. All troubleshooting
and repair procedures are detailed to allow repair at only the subassembly or module level. Because of
the complexity of the individual boards and subassemblies, do not attempt to make repairs at the
component level or modify any printed wiring board. Improper repairs can create a safety hazard. Any
indication of component replacement or printed wiring board modification may void any warranty or
exchange allowances.
Starting the Setup Utility
The Setup Utility is a ROM-based information and customization utility that can be used even when your
Windows® operating system is not working.
The utility reports information about the computer and provides settings for startup, security, and other
preferences.
To start the Setup Utility:
Open the Setup Utility by turning on or restarting the computer. While the “Press the ESC key for
Startup Menu” message is displayed in the lower-left corner of the screen, press f10.
– or –
1.
Open the Setup Utility by turning on or restarting the computer. While the “Press the ESC key for
Startup Menu” message is displayed in the lower-left corner of the screen, press esc.
2.
When the Startup Menu is displayed, press f10.
Changing the language of the Setup Utility
The following procedure explains how to change the language of the Setup Utility. If the Setup Utility is
not already running, begin at step 1. If the Setup Utility is already running, begin at step 2.
1.
Open the Setup Utility by turning on or restarting the computer. While the “Press the ESC key for
Startup Menu” message is displayed in the lower-left corner of the screen, press f10.
– or –
Open the Setup Utility by turning on or restarting the computer. While the “Press the ESC key for
Startup Menu” message is displayed in the lower-left corner of the screen, press esc. When the
Startup Menu is displayed, press f10.
88
2.
Use the arrow keys to select System Configuration > Language, and then press enter.
3.
Use the arrow keys to select a language, and then press enter.
Chapter 5 Setup Utility
4.
When a confirmation prompt with your language selected is displayed, press enter.
5.
To save your change and exit the Setup Utility, use the arrow keys to select Exit > Exit Saving
Changes, and then press enter.
Your change goes into effect immediately.
Navigating and selecting in the Setup Utility
Because the Setup Utility is not Windows based, it does not support the TouchPad. Navigation and
selection are by keystroke.
●
To choose a menu or a menu item, use the arrow keys.
●
To choose an item in a list or to toggle a field, for example an Enable/Disable field, use either the
arrow keys or f5 or f6.
●
To select an item, press enter.
●
To close a text box or return to the menu display, press esc.
●
To display additional navigation and selection information while the Setup Utility is open, press
f1.
Displaying system information
The following procedure explains how to display system information in the Setup Utility. If the Setup
Utility is not open, begin at step 1. If the Setup Utility is open, begin at step 2.
1.
Open the Setup Utility by turning on or restarting the computer. While the “Press the ESC key for
Startup Menu” message is displayed in the lower-left corner of the screen, press f10.
– or –
Open the Setup Utility by turning on or restarting the computer. While the “Press the ESC key for
Startup Menu” message is displayed in the lower-left corner of the screen, press esc. When the
Startup Menu is displayed, press f10.
2.
Select the Main menu. System information such as the system time and date, and identification
information about the computer is displayed.
3.
To exit the Setup Utility without changing any settings, use the arrow keys to select Exit > Exit
Discarding Changes, and then press enter.
Navigating and selecting in the Setup Utility
89
Restoring default settings in the Setup Utility
The following procedure explains how to restore the Setup Utility default settings. If the Setup Utility is
not already running, begin at step 1. If the Setup Utility is already running, begin at step 2.
1.
Open the Setup Utility by turning on or restarting the computer. While the “Press the ESC key for
Startup Menu” message is displayed in the lower-left corner of the screen, press f10.
– or –
Open the Setup Utility by turning on or restarting the computer. While the “Press the ESC key for
Startup Menu” message is displayed in the lower-left corner of the screen, press esc. When the
Startup Menu is displayed, press f10.
2.
Use the arrow keys to select Exit > Load Setup Defaults, and then press enter.
3.
When the Setup Confirmation is displayed, press enter.
4.
To save your change and exit the Setup Utility, use the arrow keys to select Exit > Exit Saving
Changes, and then press enter.
The Setup Utility default settings go into effect when the computer restarts.
NOTE: Your password, security, and language settings are not changed when you restore the factory
default settings.
Exiting the Setup Utility
You can exit the Setup Utility with or without saving changes.
●
To exit the Setup Utility and save your changes from the current session:
If the Setup Utility menus are not visible, press esc to return to the menu display. Then use the
arrow keys to select Exit > Exit Saving Changes, and then press enter.
●
To exit the Setup Utility without saving your changes from the current session:
If the Setup Utility menus are not visible, press esc to return to the menu display. Then use the
arrow keys to select Exit > Exit Discarding Changes, and then press enter.
After either choice, the computer restarts in Windows.
90
Chapter 5 Setup Utility
Setup Utility menus
The menu tables in this section provide an overview of Setup Utility options.
NOTE: Some of the Setup Utility menu items listed in this section may not be supported by your
computer.
Main menu
Select
To do this
System information
●
View and change the system time and date.
●
View identification information about the computer.
●
View specification information about the processor, memory size,
system BIOS, and keyboard controller version (select models only).
Security menu
Select
To do this
Administrator password
Enter, change, or delete an administrator password.
Power-On Password
Enter, change, or delete a power-on password.
System Configuration menu
Select
To do this
Language Support
Change the Setup Utility language.
Button Sound (select models only)
Enable/disable the capacitive button tapping sound.
Virtualization Technology
Enable/disable the processor Virtualization Technology.
Processor C4 State (select models only)
Enable/disable the processor C4 sleep state.
LAN Power Saving (select models only)
Enable/disable LAN Power Saving. When enabled, saves power when
the computer is in DC mode.
Card Reader/1394 Power Saving (select models
only)
Enable/disable Card Reader/1394 Power Saving. When enabled, saves
power when the computer is in DC mode.
Fan Always On
Enabled/disable Fan Always On. When enabled, the computer fan will
always be on.
Boot Options
Set the following boot options:
●
f9 and f10 Delay (sec.)―Set the delay for the f9 and f10 functions
of the Setup Utility in intervals of 5 seconds each (0, 5, 10, 15, 20).
●
CD-ROM boot―Enable/disable boot from CD-ROM.
●
Floppy boot―Enable/disable boot from diskette.
●
Internal Network Adapter boot―Enable/disable boot from Internal
Network Adapter.
●
Boot Order―Set the boot order for:
Setup Utility menus
91
Select
To do this
◦
USB Floppy
◦
Internal CD/DVD ROM Drive
◦
Hard drive
◦
USB Diskette on Key
◦
USB Hard drive
◦
Network adapter
Diagnostics menu
Select
To do this
Hard Disk Self Test
Run a comprehensive self-test on the hard drive.
NOTE: On models with two hard drives, this menu option is called the
Primary Hard Disk Self Test.
92
Secondary Hard Disk Self Test (select models
only)
Run a comprehensive self-test on a secondary hard drive.
Memory Test
Run a diagnostic test on the system memory.
Chapter 5 Setup Utility
6
Specifications
Computer specifications
Metric
U.S.
Height (front to back)
3.33 to 3.97 cm
1.31 to 1.56 in
Width
33.40 cm
13.15 in
Depth
23.70 cm
9.33 in
Weight (with optical drive, hard drive, and battery)
2.09 g
4.60 lbs
Dimensions
Input power
Operating voltage
18.5 V dc —19.0 V dc
Operating current
3.5 A or 4.74 A
Temperature
Operating (not writing to optical disc)
0°C to 35°C
32°F to 95°F
Operating (writing to optical disc)
5°C to 35°C
41°F to 95°F
Nonoperating
-20°C to 60°C
-4°F to 140°F
Relative humidity
Operating
10% to 90%
Nonoperating
5% to 95%
Maximum altitude (unpressurized)
Operating
-15 m to 3,048 m
-50 ft to 10,000 ft
Nonoperating
-15 m to 12,192 m
-50 ft to 40,000 ft
Shock
Operating
125 g, 2 ms, half-sine
Nonoperating
200 g, 2 ms, half-sine
Random vibration
Operating
0.75 g zero-to-peak, 10 Hz to 500 Hz, 0.25 oct/min sweep rate
Computer specifications
93
Metric
Nonoperating
U.S.
1.50 g zero-to-peak, 10 Hz to 500 Hz, 0.5 oct/min sweep rate
NOTE: Applicable product safety standards specify thermal limits for plastic surfaces. The computer operates well within this
range of temperatures.
14.1-inch, WXGA, BrightView display specifications
Metric
U.S.
Height
27.94 cm
11.0 in
Width
20.83 cm
8.2 in
Diagonal
35.56 cm
14.1 in
Number of colors
Up to 16.8 million
Contrast ratio
250:1 (typical)
Brightness
180 nits (typical)
Dimensions
Pixel resolution
94
Pitch
0.279 × 0.279 mm
Format
1280 × 800
Configuration
RGB vertical stripe
Backlight
Edge lit
Character display
80 × 25
Total power consumption
4W
Viewing angle
+/-40° horizontal, +20/-40° vertical (typical)
Chapter 6 Specifications
Hard drive specifications
320-GB*
250-GB*
160-GB*
120-GB*
80-GB*
Dimensions
Height
9.5 mm
9.5 mm
9.5 mm
9.5 mm
9.5 mm
Width
70 mm
70 mm
70 mm
70 mm
70 mm
102 g
102 g
102 g
102 g
SATA
SATA
SATA
SATA
Weight
101 g
Interface type
SATA
Transfer rate
Synchronous (maximum)
300 MB/sec
100 MB/sec
100 MB/sec
100 MB/sec
100 MB/sec
Security
ATA security
ATA security
ATA security
ATA security
ATA security
Single track
1.5 ms
3 ms
3 ms
3 ms
3 ms
Average
12 ms
13 ms
13 ms
13 ms
13 ms
Maximum
22 ms
24 ms
24 ms
24 ms
24 ms
Logical blocks
625,142,448
495,702,655
317,249,699
237,937,274
158,624,849
Seek times (typical read, including setting)
Disk rotational speed
Operating temperature
NOTE:
5400 rpm
5°C to 55°C (41°F to 131°F)
Certain restrictions and exclusions apply. Consult technical support for details.
*1 GB = 1 billion bytes when referring to hard drive storage capacity. Accessible capacity is less. Actual drive specifications
may differ slightly.
Hard drive specifications
95
DVD±RW and CD-RW Super Multi Double-Layer Combo
Drive specifications
Applicable disc
Read:
Write:
CD-DA, CD+(E)G, CD-MIDI, CD-TEXT,
CD-ROM, CD-ROM XA, MIXED MODE
CD, CD-I, CD-I Bridge (Photo-CD, Video
CD), Multisession CD (Photo-CD, CDEXTRA, Portfolio, CD-R, CD-RW), CD-R,
CD-RW, DVD-ROM (DVD-5, DVD-9,
DVD-10, DVD-18), DVD-R, DVD-RW,
DVD+R, DVD+RW, DVD-RAM
CD-R and CD-RW
Access time
CD
DVD
Random
< 175 ms
< 230 ms
Cache buffer
2 MB
Data transfer rate
96
24X CD-ROM
3,600 KB/sec
8X DVD
10,800 KB/sec
24X CD-R
3,600 KB/sec
16X CD-RW
2,400 KB/sec
8X DVD+R
10,800 KB/sec
4X DVD+RW
5,400 KB/sec
8X DVD-R
10,800 KB/sec
4X DVD-RW
5,400 KB/sec
2.4X DVD+R(9)
2,700 KB/sec
5X DVD-RAM
6,750 KB/sec
Transfer mode
Multiword DMA Mode
Chapter 6 Specifications
DVD+R, DVD+RW, DVD-R, DVD-RW,
DVD-RAM
System DMA specifications
Hardware DMA
System function
DMA0
Not applicable
DMA1*
Not applicable
DMA2*
Not applicable
DMA3
Not applicable
DMA4
Direct memory access controller
DMA5*
Available for PC Card†
DMA6
Not assigned
DMA7
Not assigned
*PC Card controller can use DMA 1, 2, or 5.
†Not assigned for computer models with AMD processors.
System DMA specifications
97
System interrupt specifications—Intel processors
Hardware IRQ
System function
IRQ0
System timer
IRQ1
Standard 101-/102-Key or Microsoft® Natural Keyboard
IRQ2
Cascaded
IRQ3
Intel 82801DB/DBM USB2 Enhanced Host Controller—24CD
IRQ4
COM1
IRQ5*
Conexant AC—Link Audio Intel 82801DB/DBM SMBus Controller—24C3 Data Fax
Modem with SmartCP
IRQ6
Diskette drive
IRQ7*
Parallel port
IRQ8
System CMOS/real-time clock
IRQ9*
Microsoft ACPI-compliant system
IRQ10*
Intel USB UHCI controller—24C2
Intel 82852/82855 GM/GME Graphic Controller
Realtek RTL8139 Family PCI Fast Ethernet Controller
IRQ11
Intel USB EHCI controller—24CD
Intel USB UHCI controller—24C4
Intel USB UHCI controller—24C7
Intel Pro/Wireless 2200BG
TI OHCI 1394 host controller
TI PCI1410 CardBus controller
IRQ12
Synaptics PS/2 TouchPad
IRQ13
Numeric data processor
IRQ14
Primary IDE channel
IRQ15
Secondary IDE channel
*Default configuration; audio possible configurations are IRQ5, IRQ7, IRQ9, IRQ10, or none.
NOTE: PC Cards may assert IRQ3, IRQ4, IRQ5, IRQ7, IRQ9, IRQ10, IRQ11, or IRQ15. The serial port may assert IRQ3 or
IRQ4.
98
Chapter 6 Specifications
System interrupt specifications—AMD processors
Hardware IRQ
System function
ISA0
High precision event timer
ISA1
Standard 101/102-Key or Microsoft Natural PS/2 Keyboard
ISA8
High precision event timer
ISA12
Alps Pointing-device (2 way)
ISA13
Numeric data processor
ISA14
ATA Channel 0
ISA15
ATA Channel 1
PCI5
Ricoh OHCI Compliant IEEE 1394 Host Controller
PCI7
Ricoh Memory Stick Controller
PCI7
Ricoh SD/MMC Host Controller
PCI7
Ricoh xD-Picture Card Controller
PCI7
SDA Standard Compliant SD Host Controller
PC10
NVIDIA nForce PCI System Management
PC16
Standard Enhanced PCI to USB Host Controller
PC16
Standard OpenHCD USB Host Controller
PC17
Standard Enhanced PCI to USB Host Controller
PC17
Standard OpenHCD USB Host Controller
PC18
NVIDIA nForce PCI System Management
PC19
Broadcom 802.11b/g WLAN
PCI-2
PCI standard PCI-to-PCI bridge
PC21
High Definition Audio Controller
PC22
Standard Dual Channel PCI IDE Controller
PC23
NVIDIA MCP67M
PC-3
PCI standard PCI-to-PCI bridge
PC-4
NVIDIA nForce Networking Controller
System interrupt specifications—AMD processors
99
System I/O address specifications—Intel processors
I/O address (hex)
System function (shipping configuration)
000 - 00F
DMA controller no. 1
010 - 01F
Unused
020 - 021
Interrupt controller no. 1
022 - 024
Opti chipset configuration registers
025 - 03F
Unused
02E - 02F
87334 “Super I/O” configuration for CPU
040 - 05F
Counter/timer registers
044 - 05F
Unused
060
Keyboard controller
061
Port B
062 - 063
Unused
064
Keyboard controller
065 - 06F
Unused
070 - 071
NMI enable/RTC
072 - 07F
Unused
080 - 08F
DMA page registers
090 - 091
Unused
092
Port A
093 - 09F
Unused
0A0 - 0A1
Interrupt controller no. 2
I/O Address (hex)
System Function (shipping configuration)
0A2 - 0BF
Unused
0C0 - 0DF
DMA controller no. 2
0E0 - 0EF
Unused
0F0 - 0F1
Coprocessor busy clear/reset
0F2 - 0FF
Unused
100 - 16F
Unused
170 - 177
Secondary fixed disk controller
178 - 1EF
Unused
1F0 - 1F7
Primary fixed disk controller
1F8 - 200
Unused
201
JoyStick (decoded in ESS1688)
202 - 21F
Unused
100 Chapter 6 Specifications
I/O address (hex)
System function (shipping configuration)
220 - 22F
Entertainment audio
230 - 26D
Unused
26E - 26
Unused
278 - 27F
Unused
280 - 2AB
Unused
2A0 - 2A7
Unused
2A8 - 2E7
Unused
2E8 - 2EF
Reserved serial port
2F0 - 2F7
Unused
300 - 31F
Unused
320 - 36F
Unused
370 - 377
Secondary diskette drive controller
378 - 37F
Parallel port (LPT1/default)
380 - 387
Unused
388 - 38B
FM synthesizer—OPL3
38C - 3AF
Unused
3B0 - 3BB
VGA
3BC - 3BF
Reserved (parallel port/no EPP support)
3C0 - 3DF
VGA
3E0 - 3E1
PC Card controller in CPU
3E2 - 3E3
Unused
3E8 - 3EF
Internal modem
3F0 - 3F7
“A” diskette controller
3F8 - 3FF
Serial port (COM1/default)
CF8 - CFB
PCI configuration index register (PCIDIVO-1)
CFC - CFF
PCI configuration data register (PCIDIVO-1)
System I/O address specifications—Intel processors 101
System I/O address specifications—AMD processors
I/O address (hex)
System function (shipping configuration)
000 - 008
Direct memory access controller
000 - CF7
PCI Bus
00A - 00F
Direct memory access controller
010 - 01F
Motherboard resources
020 - 021
Programmable interrupt controller
022 - 03F
Motherboard resources
040 - 043
System timer
044 - 05F
Motherboard resources
060 - 060
Standard 101/102-Key or Microsoft Natural PS/2 Keyboard
061 - 061
System speaker
062 - 062
Microsoft ACPI-Compliant Embedded Controller
063 - 063
Motherboard resources
064 - 064
Standard 101/102-Key or Microsoft Natural PS/2 Keyboard
065 - 065
Motherboard resources
066 - 066
Microsoft ACPI-Compliant Embedded Controller
067 - 06F
Motherboard resources
070 - 071
System CMOS/real time clock
072 - 073
Motherboard resources
074 - 07f
Motherboard resources
080 - 080
Motherboard resources
081 - 083
Direct memory access controller
087 - 087
Direct memory access controller
089 - 08B
Direct memory access controller
08F - 08F
Direct memory access controller
091 - 093
Motherboard resources
097 - 09F
Motherboard resources
0A0 - 0A1
Programmable interrupt controller
0A2 - 0BF
Motherboard resources
0C0 - 0D1
Direct memory access controller
0D4 - 0DF
Direct memory access controller
0E0 - 0EF
Motherboard resources
0F0 - 0F1
Numeric data processor
1F0 - 1F7
ATA Channel 0
102 Chapter 6 Specifications
I/O address (hex)
System function (shipping configuration)
360 - 361
Motherboard resources
376 - 376
ATA Channel 1
3B0 - 3BB
NVIDIA MCP67M
3C0 - 3DF
NVIDIA MCP67M
3F6 - 3F6
ATA Channel 0
4D0 - 4D1
Motherboard resources
0D00 - FFFF
PCI bus
1000 - 107F
Motherboard resources
1080 - 10FF
Motherboard resources
1400 - 147F
Motherboard resources
1480 - 14FF
Motherboard resources
1800 - 187F
Motherboard resources
1880 - 18FF
Motherboard resources
3000 - 303F
NVIDIA nFOrce PCI System Management
3040 - 307F
NVIDIA nFOrce PCI System Management
3080 - 30BF
NVIDIA nFOrce PCI System Management
30C0 - 30CF
Standard Dual Channel PCI IDE Controller
30D0 - 30DF
Standard Dual Channel PCI IDE Controller
30E0 - 30E3
Standard Dual Channel PCI IDE Controller
30E4 - 30E7
Standard Dual Channel PCI IDE Controller
30E8 - 30EF
Standard Dual Channel PCI IDE Controller
30F0 - 30F7
Standard Dual Channel PCI IDE Controller
400 - 4FFF
PCI standard PCI-to-PCI bridge
System I/O address specifications—AMD processors 103
System memory map specifications—Intel processors
Size
Memory address
System function
640 KB
00000000-0009FFFF
Base memory
128 KB
000A0000-000BFFFF
Video memory
48 KB
000C0000-000CBFFF
Video BIOS
160 KB
000C8000-000E7FFF
Unused
64 KB
000E8000-000FFFFF
System BIOS
15 MB
00100000-00FFFFFF
Extended memory
58 MB
04800000-07FFFFFF
Super extended memory
58 MB
04800000-07FFFFFF
Unused
2 MB
08000000-080FFFFF
Video memory (direct access)
4 GB
08200000-FFFEFFFF
Unused
64 KB
FFFF0000-FFFFFFFF
System BIOS
System memory map specifications—AMD processors
Memory address
System function
000A0000 - 000BFFFF
NVIDIA MCP67M
000A0000 - 000BFFFF
PCI bus
000C0000 - 000C3FFF
PCI bus
000C4000 - 000C7FFF
PCI bus
000C80000 - 00CBFFF
PCI bus
000CC000 - 000CFFFF
PCI bus
000D000 - 00D3FFF
PCI bus
000D4000 - 000D7FFF
PCI bus
000D800 - 00DBFFF
PCI bus
000DC00 - 00DFFFF
PCI bus
000E0000 - 00E3FFF
PCI bus
000E4000 - 000E7FFF
PCI bus
000E800 - 000EBFFF
PCI bus
000EC00 - 000EFFFF
PCI bus
000F0000 - 000FFFFF
PCI bus
4000000 - FEBFFFFF
PCI bus
D0000000 - DFFFFFFF
NVIDIA MCP67M
E000000 - EFFFFFFF
Motherboard resources
104 Chapter 6 Specifications
Memory address
System function
F00000 - F3FFFFFF
PCI standard PCI-to-PCI bridge
F4000000 - F4FFFFFF
NVIDIA MCP67M
F500000 - F5FFFFFF
NVIDIA MCP67M
F6000000 – F6003FFF
Broadcom 802.11b/g WLAN
F600000 - F60FFFFF
PCI standard PCI-to-PCI bridge
F610000 - F61007FF
RICOH OHCI Compliant IEEE 1394 Host Controller
F6100000 - F61FFFFF
PCI standard PCI-to-PCI bridge
F6100800 - F61008FF
SDA Standard Compliant SD Host Controller
F6100C00 - F6100CFF
Ricoh SD/MMC Host Controller
F6101000 - F61010FF
Ricoh Memory Stick Controller
F6101400 - F61014FF
Ricoh xD-Picture Card Controller
F620000 - F627FFFF
NVIDIA nForce System Management Controller
F6480000 - F6483FFF
High Definition Audio Controller
F6484000 - F6485FFF
Standard Dual Channel PCI IDE Controller
F6486000 - F6486FFF
Standard OpenHCD USB Host Controller
F6487000 - F6487FFF
Standard OpenHCD USB Host Controller
F6488000 - F6488FFF
NVIDIA nForce Networking Controller
F6489000 - F64890FF
Standard Enhanced PCI to USB Host Controller
FF6489400 - F64894FF
Standard Enhanced PCI to USB Host Controller
F6489800 - F648980F
NVIDIA nForce Networking Controller
F6489C00 - F6489CFF
NVIDIA nForce Networking Controller
FEC00000 - FEC00FFF
System board
FEC80000 - FEC80FFF
System board
FED00000 - FED003FF
High precision event timer
FEE00000 - FEEFFFFF
System board
FEF00000 - FEF00FFF
System board
FFC00000 - FFFFFFFF
System board
System memory map specifications—AMD processors 105
7
Screw listing
This section provides specification and reference information for the screws and screw locks used in
the computer. All screws listed in this section are available in the Screw Kit, spare part number
487298-001, and the Display Screw Kit, spare part number 486730-001.
106 Chapter 7 Screw listing
Black Phillips PM2.5×4.0 screw
Color
Quantity
Length
Thread
Head diameter
Black
13
4.0 mm
2.5 mm
5.0 mm
Where used: 2 screws that secure the wireless antenna transceivers to the display enclosure
Where used: 6 screws that secure the display panel to the display enclosure
Black Phillips PM2.5×4.0 screw 107
Where used: 3 screws that secure the top cover to the computer
Where used: 2 screws that secure the speaker to the computer
108 Chapter 7 Screw listing
Black Phillips PM2.5×6.0 captive screw
Color
Quantity
Length
Thread
Head diameter
Black
5
6.0 mm
2.5 mm
5.0 mm
Where used: 5 screws that secure the hard drive compartment cover, Mini Card compartment cover,
and memory module cover to the computer
Black Phillips PM2.5×6.0 captive screw 109
Black Phillips PM2.0×2.0 broad head screw
Color
Quantity
Length
Thread
Head diameter
Black
1
2.0 mm
2.0 mm
7.0 mm
Where used: One screw that secures the switch cover to the computer
110 Chapter 7 Screw listing
Silver Phillips PM1.5×9.0 screw
Color
Quantity
Length
Thread
Head diameter
Silver
2
9.0 mm
1.5 mm
4.0 mm
Where used: 2 screws that secure the expansion port connector to the computer
Silver Phillips PM1.5×9.0 screw 111
Black Phillips PM2.5×3.0 screw
Color
Quantity
Length
Thread
Head diameter
Black
2
3.0 mm
2.5 mm
5.0 mm
Where used: 2 screws that secure the audio board to the computer
112 Chapter 7 Screw listing
Black Phillips PM2.5×17.0 screw
Color
Quantity
Length
Thread
Head diameter
Black
3
17.0 mm
2.5 mm
5.0 mm
Where used: 3 screws that secure the keyboard to the computer
Black Phillips PM2.5×17.0 screw 113
Black Phillips PM2.5×6.0 screw
Color
Quantity
Length
Thread
Head diameter
Black
4
6.0 mm
2.5 mm
5.0 mm
Where used: 2 screws that secure the top cover to the base enclosure
Where used: 2 screws that secure the system fan to the computer
114 Chapter 7 Screw listing
Black Phillips PM2.5×7.0 screw
Color
Quantity
Length
Thread
Head diameter
Silver
17
7.0 mm
2.5 mm
5.0 mm
Where used: 4 screws that secure the display assembly to the computer
Where used: 2 screws that secure the display bezel to the display assembly
Black Phillips PM2.5×7.0 screw 115
Where used: 6 screws that secure the optical drive, switch cover, and keyboard to the computer
Where used: 2 screws that secure the top cover to the computer
Where used: 2 screws that secure the top cover to the computer
116 Chapter 7 Screw listing
Where used: One screw that secures the USB board to the base enclosure
Black Phillips PM2.5×7.0 screw 117
Silver Phillips PM3.0×4.0 screw
Color
Quantity
Length
Thread
Head diameter
Silver
4
4.0 mm
3.0 mm
5.0 mm
Where used: 4 screws that secure the hard drive bracket to the hard drive
118 Chapter 7 Screw listing
Silver Phillips PM2.0×4.0 screw
Color
Quantity
Length
Thread
Head diameter
Silver
8
4.0 mm
2.0 mm
5.0 mm
Where used: 8 screws that secure the display hinges to the display
Silver Phillips PM2.0×4.0 screw 119
Black Phillips PM2.0×4.0 screw
Color
Quantity
Length
Thread
Head diameter
Black
12
4.0 mm
2.0 mm
5.0 mm
Where used: 2 screws that secure the optical drive bracket to the optical drive
Where used: 2 screws that secure the WLAN module to the computer
120 Chapter 7 Screw listing
Where used: 3 screws that secure the switch cover to the computer
Where used: 1 screw that secures the power button board to the computer
Where used: 2 screws that secure the Bluetooth module to the computer
Black Phillips PM2.0×4.0 screw 121
Where used: 2 screws that secure the modem module to the computer
122 Chapter 7 Screw listing
Silver Phillips PM2.0×10.0 captive screw
Color
Quantity
Length
Thread
Head diameter
Silver
4
10.0 mm
2.0 mm
5.0 mm
Where used: 4 captive screws that secure the fan/heat sink assembly to the system board
Silver Phillips PM2.0×10.0 captive screw 123
8
Backup and recovery
Recovering system information
Recovery after a system failure is as complete as your most current backup. HP recommends that you
create recovery discs immediately after software setup. As you add new software and data files, you
should continue to back up your system on a regular basis to maintain a reasonably current backup.
Tools provided by the operating system and Recovery Manager software are designed to help you with
the following tasks for safeguarding your information and restoring it in case of a system failure:
●
Making a set of recovery discs (Recovery Manager software feature). Recovery discs are used to
start up (boot) your computer and restore the operating system and software programs to factory
settings in case of system failure or instability.
●
Backing up your information regularly to protect your important system files.
●
Creating system restore points (operating system feature). System restore points allow you to
reverse undesirable changes to your computer by restoring the computer to an earlier state.
●
Recovering a program or driver (Recovery Manager software feature). This feature helps you
reinstall a program or driver without performing a full system recovery.
●
Performing a full system recovery (Recovery Manager software feature). With Recovery Manager,
you can recover your full factory image if you experience system failure or instability. Recovery
Manager works from a dedicated recovery partition (select models only) on the hard drive or from
recovery discs you create.
NOTE: If your computer includes a solid-state drive (SSD), you may not have a recovery partition.
Recovery discs have been included for computers that do not have a partition. Use these discs to
recover your operating system and software. To check for the presence of a recovery partition,
select Start > Computer. If the partition is present, an HP Recovery drive is listed in the Hard Disk
Drives section of the window.
Backing up your information
When to back up
●
On a regularly scheduled basis
NOTE: Set reminders to back up your information periodically.
●
Before the computer is repaired or restored
●
Before you add or modify hardware or software
124 Chapter 8 Backup and recovery
Backup suggestions
●
Create a set of recovery discs using Recovery Manager.
●
Create system restore points using the Windows® System Restore feature, and periodically copy
them to disc.
●
Store personal files in the Documents folder and back up these folders periodically.
●
Back up templates stored in their associated programs.
●
Save customized settings in a window, toolbar, or menu bar by taking a screen shot of your settings.
The screen shot can be a time saver if you have to reset your preferences.
To copy the screen and paste it into a word-processing document, follow these steps:
a.
Display the screen.
b.
Copy the screen:
To copy only the active window, press alt+fn+prt sc.
To copy the entire screen, press fn+prt sc.
c.
Open a word-processing document, and then select Edit > Paste.
Using system restore points
When you back up your system, you are creating a system restore point. A system restore point allows
you to save and name a snapshot of your hard drive at a specific point in time. You can then recover
back to that point if you want to reverse subsequent changes made to your system.
NOTE: Recovering to an earlier restore point does not affect data files saved or e-mails created since
the last restore point.
You also can create additional restore points to provide increased protection for your system files and
settings.
When to create restore points
●
Before you add or extensively modify software or hardware
●
Periodically, whenever the system is performing optimally
NOTE:
If you revert to a restore point and then change your mind, you can reverse the restoration.
Create a system restore point
1.
Select Start > Control Panel > System and Maintenance > System.
2.
In the left pane, click System protection.
3.
Click the System Protection tab.
4.
Under Automatic restore points, select the disk for which you want to create a restore point.
5.
Click Create.
Recovering system information 125
The System Protection window opens.
6.
Follow the on-screen instructions.
Restore to a previous date and time
To revert to a restore point (created at a previous date and time), when the computer was functioning
optimally, follow these steps:
1.
Select Start > Control Panel > System and Maintenance > System.
2.
In the left pane, click System protection.
3.
Click the System Protection tab.
4.
Click the System Restore button, and then click Next.
The System Restore window opens.
5.
Follow the on-screen instructions.
Creating recovery discs
NOTE: HP recommends that you create recovery discs to be sure that you can restore your system
to its original factory state if you experience serious system failure or instability. Create these discs after
setting up the computer for the first time.
NOTE: Handle these discs carefully and keep them in a safe place. The software allows the creation
of only one set of recovery discs.
Note the following guidelines before creating recovery discs:
●
You will need high quality CD-R, DVD-R, double-layer DVD-R, DVD+R, double-layer DVD+R, or
BD-R (writable Blu-ray) discs. All these discs are purchased separately.
NOTE: Read-write discs, such as CD-RW, DVD ± RW, double-layer DVD±RW, and BD-RE
(rewritable Blu-ray) discs, are not compatible with the Recovery Manager software.
●
The computer must be connected to AC power during this process.
●
Only one set of recovery discs can be created per computer.
●
Number each disc before inserting it into the computer optical drive.
●
If necessary, you can exit the program before you have finished creating the recovery discs. The
next time you open Recovery Manager, you will be prompted to continue the disc creation process.
To create a set of recovery discs:
1.
Select Start > All Programs > Recovery Manager > Recovery Manager.
Recovery Manager opens.
2.
Click Advanced Options.
NOTE: If you are operating the computer on battery power, you will be prompted to connect to
AC power before you can go to the next step.
126 Chapter 8 Backup and recovery
3.
Click Recovery disc creation, and then click Next.
4.
Follow the on-screen instructions.
Performing a recovery
NOTE: You can recover only files that you have previously backed up. HP recommends that you use
Recovery Manager to create an entire drive backup as soon as you set up your computer.
Recovery Manager software allows you to repair or restore the system if you experience system failure
or instability. Recovery Manager works from recovery discs that you create or from a dedicated recovery
partition (select models only) on the hard drive. However, if your computer includes a solid-state drive
(SSD), you may not have a recovery partition. If that is the case, recovery discs have been included
with your computer. Use these discs to recover your operating system and software.
NOTE: Windows has its own built-in repair features, such as System Restore and driver roll-back
capabilities. If you have not already tried these features, try them before using Recovery Manager.
NOTE: Recovery Manager recovers only software that was preinstalled at the factory. Software not
provided with this computer must be downloaded from the manufacturer's Web site or reinstalled from
the disc provided by the manufacturer.
Recovering from the recovery discs
To restore the system from the recovery discs:
1.
Back up all personal files.
2.
Insert the first recovery disc into the optical drive and restart the computer.
3.
Follow the on-screen instructions.
Recovering from the dedicated recovery partition (select models only)
NOTE: If your computer includes a solid-state drive (SSD), you may not have a recovery partition. You
will not be able to recover using this procedure. Recovery discs have been included for computers that
do not have a partition. Use these discs to recover your operating system and software.
On some models, you can perform a recovery from the partition on the hard drive from either the Start
button or f11.
To restore the system from the partition, follow these steps:
1.
Access Recovery Manager in either of the following ways:
●
Select Start > All Programs > Recovery Manager > Recovery Manager.
–or–
●
Restart the computer and press f11 while the “Press <F11> for recovery” message is displayed
on the screen. Then select Recovery Manager.
Recovery Manager opens.
2.
Click Advanced Options.
Recovering system information 127
3.
Click System recovery, and then click Next.
4.
Follow the on-screen instructions.
128 Chapter 8 Backup and recovery
9
Connector pin assignments
Audio-out (headphone)
Pin
Signal
1
Audio out, left channel
2
Audio out, right channel
3
Ground
Audio-in (microphone)
Pin
Signal
1
Audio signal in
2
Audio signal in
3
Ground
Audio-out (headphone) 129
External monitor
Pin
Signal
1
Red analog
2
Green analog
3
Blue analog
4
Not connected
5
Ground
6
Ground analog
7
Ground analog
8
Ground analog
9
+5 VDC
10
Ground
11
Monitor detect
12
DDC 2B data
13
Horizontal sync
14
Vertical sync
15
DDC 2B clock
130 Chapter 9 Connector pin assignments
RJ-11 (modem)
Pin
Signal
1
Unused
2
Tip
3
Ring
4
Unused
5
Unused
6
Unused
RJ-45 (network)
Pin
Signal
1
Transmit +
2
Transmit -
3
Receive +
4
Unused
5
Unused
6
Receive -
7
Unused
8
Unused
RJ-11 (modem) 131
HDMI
Pin
Signal
1
TMDS data 2+
2
TMDS data 2 shield
3
TMDS data 2–
4
TMDS data 1+
5
TMDS data 1shield
6
TMDS data 1–
7
TMDS data 0+
8
TMDS data 0 shield
9
TMDS data 0–
10
TMDS clock+
11
TMDS clock shield
12
TMDS clock–
13
CEC
14
No connect
15
DDC clock
16
DDC data
17
Ground
18
+5V power
19
Hot plug detect
20
Shell
Universal Serial Bus
132 Chapter 9 Connector pin assignments
Pin
Signal
1
+5 VDC
2
Data -
3
Data +
4
Ground
Universal Serial Bus 133
10 Power cord set requirements
The wide range input feature of the computer permits it to operate from any line voltage from 100 to 120
volts AC or from 220 to 240 volts AC.
The 3-conductor power cord set included with the computer meets the requirements for use in the
country or region where the equipment is purchased.
Power cord sets for use in other countries or regions must meet the requirements of the country or region
where the computer is used.
Requirements for all countries or regions
The requirements listed below are applicable to all countries or regions:
●
The length of the power cord set must be at least 1.5 m (5.0 ft) and no more than 2.0 m (6.5 ft).
●
All power cord sets must be approved by an acceptable accredited agency responsible for
evaluation in the country or region where the power cord set will be used.
●
The power cord sets must have a minimum current capacity of 10 amps and a nominal voltage
rating of 125 or 250 V AC, as required by each country or region’s power system.
●
The appliance coupler must meet the mechanical configuration of an EN 60 320/IEC 320 Standard
Sheet C13 connector for mating with the appliance inlet on the back of the computer.
134 Chapter 10 Power cord set requirements
Requirements for specific countries or regions
Country/region
Accredited agency
Applicable note number
Australia
EANSW
1
Austria
OVE
1
Belgium
CEBC
1
Canada
CSA
2
Denmark
DEMKO
1
Finland
FIMKO
1
France
UTE
1
Germany
VDE
1
Italy
IMQ
1
Japan
METI
3
The Netherlands
KEMA
1
Norway
NEMKO
1
The People's Republic of China
CCC
5
South Korea
EK
4
Sweden
SEMKO
1
Switzerland
SEV
1
Taiwan
BSMI
4
The United Kingdom
BSI
1
The United States
UL
2
1.
The flexible cord must be Type HO5VV-F, 3-conductor, 1.0-mm² conductor size. Power cord set fittings (appliance coupler
and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it
will be used.
2.
The flexible cord must be Type SPT-3 or equivalent, No. 18 AWG, 3-conductor. The wall plug must be a two-pole grounding
type with a NEMA 5-15P (15 A, 125 V) or NEMA 6-15P (15 A, 250 V) configuration.
3.
The appliance coupler, flexible cord, and wall plug must bear a “T” mark and registration number in accordance with the
Japanese Dentori Law. The flexible cord must be Type VCT or VCTF, 3-conductor, 1.00-mm² conductor size. The wall
plug must be a two-pole grounding type with a Japanese Industrial Standard C8303 (7 A, 125 V) configuration.
4.
The flexible cord must be Type RVV, 3-conductor, 0.75-mm² conductor size. Power cord set fittings (appliance coupler
and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it
will be used.
5.
The flexible cord must be Type VCTF, 3-conductor, 0.75-mm² conductor size. Power cord set fittings (appliance coupler
and wall plug) must bear the certification mark of the agency responsible for evaluation in the country or region where it
will be used.
Requirements for specific countries or regions 135
11 Recycling
Battery
When a battery has reached the end of its useful life, do not dispose of the battery in general household
waste. Follow the local laws and regulations in your area for computer battery disposal.
Display
WARNING! The backlight contains mercury. Caution must be exercised when removing and handling
the backlight to avoid damaging this component and causing exposure to the mercury.
CAUTION: The procedures in this appendix can result in damage to display components. The only
components intended for recycling purposes are the liquid crystal display (LCD) panel and the backlight.
Careful handling must be exercised when removing these components.
NOTE: Materials Disposal. This HP product contains mercury in the backlight in the display assembly
that might require special handling at end-of-life. Disposal of mercury may be regulated because of
environmental considerations. For disposal or recycling information, contact your local authorities, or
see the Electronic Industries Alliance (EIA) Web site at http://www.eiae.org.
This section provides disassembly instructions for the display assembly. The display assembly must be
disassembled to gain access to the backlight (1) and the liquid crystal display (LCD) panel (2).
NOTE: The procedures provided in this appendix are general disassembly instructions. Specific
details, such as screw sizes, quantities, and locations, and component shapes and sizes, can vary from
one computer model to another.
136 Chapter 11 Recycling
Perform the following steps to disassemble the display assembly:
1.
Remove all screw covers (1) and screws (2) that secure the display bezel to the display assembly.
2.
Lift up and out on the left and right inside edges (1) and the top and bottom inside edges (2) of the
display bezel until the bezel disengages from the display assembly.
3.
Remove the display bezel (3).
Display 137
4.
Disconnect all display panel cables (1) from the display inverter and remove the inverter (2).
5.
Remove all screws (1) that secure the display panel assembly to the display enclosure.
6.
Remove the display panel assembly (2) from the display enclosure.
7.
Turn the display panel assembly upside down.
8.
Remove all screws that secure the display panel frame to the display panel.
9.
Use a sharp-edged tool to cut the tape (1) that secures the sides of the display panel to the display
panel frame.
138 Chapter 11 Recycling
10. Remove the display panel frame (2) from the display panel.
11. Remove the screws (1) that secure the backlight cover to the display panel.
12. Lift the top edge of the backlight cover (2) and swing it outward.
13. Remove the backlight cover.
14. Turn the display panel right-side up.
Display 139
15. Remove the backlight cables (1) from the clip (2) in the display panel.
16. Turn the display panel upside down.
17. Remove the backlight frame from the display panel.
WARNING! The backlight contains mercury. Exercise caution when removing and handling the
backlight to avoid damaging this component and causing exposure to the mercury.
18. Remove the backlight from the backlight frame.
140 Chapter 11 Recycling
19. Disconnect the display cable (1) from the LCD panel.
20. Remove the screws (2) that secure the LCD panel to the display rear panel.
21. Release the LCD panel (3) from the display rear panel.
22. Release the tape (4) that secures the LCD panel to the display rear panel.
23. Remove the LCD panel.
24. Recycle the LCD panel and backlight.
Display 141
Index
Symbols/Numerics
1394 Power Saving 91
A
AC adapter, spare part
numbers 27, 29
administrator password 91
antenna
removal 64
spare part number 24, 65
Antenna Kit, spare part
number 24
antenna, microphone cable kit,
spare part number 32
applications key, Windows 10
audio board
removal 74
spare part number 21, 31,
74
audio cable kit, spare part
number 30
audio, product description 3
audio-in (microphone) jack,
identifying 13
audio-in jack, pin
assignments 129
audio-out (headphone) jack,
identifying 13
audio-out jack, pin
assignments 129
B
backing up
customized window, toolbar,
and menu bar settings 125
personal files 125
templates 125
backup suggestions 125
base enclosure, spare part
number 21, 32
142 Index
battery
removal 41
spare part numbers 23, 31,
41
battery bay, identifying 16
battery light, identifying 7, 13
battery release latch,
identifying 16
bays
battery 16
hard drive 16
BD/DVD±R/RW Super Multi
Double-Layer Combo Drive
removal 42
bezel
illustrated 24
spare part number 24, 30,
62
Bluetooth module
removal 71
spare part number 23, 29,
71
Bluetooth module cable, spare part
number 30
boot options 91
boot order 91
button sound 91
buttons
media 8
power 8
TouchPad 6
TouchPad on/off 6
volume mute 9
wireless 9
C
cables, service considerations 34
camera module
removal 65
spare part number 65
camera, product description 3
camera/microphone module, spare
part number 31
caps lock light, identifying 7
Card Reader Power Saving 91
changing the Setup Utility
language 88
chipset, product description 1
CMOS clearing 38
compartments
memory module 16
Mini Card 16
components
bottom 16
front 6, 13
left-side 14
rear 15
right-side 15
top 6
computer feet
locations 40
spare part number 23, 30,
40
computer specifications 93
connector pin assignments
audio-in 129
audio-out 129
external monitor 130
HDMI 132
headphone 129
microphone 129
modem 131
monitor 130
network 131
RJ-11 131
RJ-45 131
Universal Serial Bus
(USB) 132
connector, power 15
connectors, service
considerations 34
D
Diagnostics menu 92
Digital Media Slot light,
identifying 14
Digital Media Slot, identifying 14
diskette drive
precautions 34
product description 3
display assembly
removal 60
spare part number 18, 30,
60
display bezel
illustrated 24
spare part number 24, 30,
62
display cable, spare part
number 24
display components
illustrated 24
recycling 136
spare part numbers 24
display enclosure
illustrated 24
spare part number 24, 30
display hinge
removal 64
spare part number 30, 64
Display Hinge Kit, spare part
number 24
display inverter
illustrated 24
spare part number 24, 30
display lid switch module, spare part
number 32
display panel
illustrated 24
product description 2
removal 63
spare part number 24, 30,
31, 63
Display Screw Kit, spare part
number 30
Display screw kit, spare part
number 24
display specifications 94
display switch, identifying 11
displaying system information 89
drive light, identifying 7, 13
drives
boot order 91
preventing damage 34
DVD/CD-RW Combo Drive
precautions 34
removal 42
specifications 96
DVD±RW and CD-RW Combo
Drive
precautions 34
removal 42
spare part number 22, 26,
31, 42
spare part numbers 22, 26,
29, 42
specifications 96
E
electrostatic discharge 35
eSATA/USB port, identifying 14
esc key, identifying 10
Ethernet, product description 3
exiting the Setup Utility 90
expansion port, identifying 14
ExpressCard slot bezel,
illustrated 25
ExpressCard slot, identifying 14
external media cards, product
description 4
external monitor port
identifying 14
pin assignments 130
F
F11 127
fan always on 91
fan, spare part number 19, 30
fan/heat sink assembly
removal 82
spare part number 19, 30,
31, 32, 82
feet
locations 40
spare part number 23, 30,
40
fn key, identifying 10
front components 6
full system recovery 124
function keys, identifying 10
G
graphics, product description
grounding equipment and
methods 37
2
H
hard drive
precautions 34
product description 2
removal 44
spare part numbers 21, 26,
28, 32, 44
specifications 95
hard drive bay, identifying 16
hard drive cover
illustrated 25
removal 45
hard drive hardware kit, spare part
number 22, 26, 29
hard drive self test 92
HDMI port, identifying 14
HDMI port, pin assignments 132
headphone (audio-out) jack 13
headphone jack, pin
assignments 129
hinge
removal 64
spare part number 30, 64
I
I/O address specifications 100,
102
integrated webcam light,
identifying 11
integrated webcam,
identifying 11
internal display switch,
identifying 11
internal microphones,
identifying 11
interrupt specifications 98, 99
inverter
illustrated 24
removal 62
spare part number 24, 30,
63
Index 143
J
jacks
audio-in (microphone) 13
audio-out (headphone) 13
RJ-11 (modem) 15
RJ-45 (network 14
K
keyboard
product description 4
removal 54
spare part numbers 19, 30,
54
keypad keys, identifying 10
keys
esc 10
fn 10
function 10
keypad 10
navigation 10
Windows applications 10
Windows logo 10
L
LAN Power Saving 91
language support 91
latch, battery release 16
lights
battery 7, 13
caps lock 7
Digital Media Slot 14
drive 7, 13
mute 7
num lock 8
optical drive 15
power 7, 13
TouchPad 6
volume down 7
volume mute 7
volume up 8
webcam 11
wireless 7
M
main menu 91
mass storage devices, spare part
numbers 26
media button, identifying 8
memory map
specifications 104
144 Index
memory module
product description 2
removal 52
spare part numbers 22, 28,
29, 52
memory module compartment
cover
illustrated 25
removal 53
spare part number 53
memory module compartment,
identifying 16
memory test 92
microphone (audio-in) jack 13
microphone jack, pin
assignments 129
microphone, product
description 3
Mini Card compartment,
identifying 16
model name 1
modem jack, pin
assignments 131
modem module
product description 3
removal 73
spare part number 20, 29,
73
modem module cable
removal 81
spare part number 32
monitor port, external 14
monitor port, pin
assignments 130
mute button, identifying 9
mute light, identifying 7
N
navigating in the Setup Utility 89
navigation keys, identifying 10
network jack, pin
assignments 131
num lock light, identifying 8
O
operating system, product
description 4
optical drive
precautions 34
product description 3
removal 42
spare part numbers 22, 26,
42
specifications 96
optical drive light, identifying 15
optical drive, identifying 15
P
packing guidelines 36
password clearing 38
performing a recovery 127
plastic parts 33
Plastics Kit
contents 25
spare part number 19, 25
pointing device, product
description 4
ports
eSATA/USB 14
expansion 14
external monitor 14
HDMI 14
product description 4
USB 15
power button board, spare part
number 32
power button, identifying 8
power connector cable
removal 77
spare part number 19, 30,
77
power connector, identifying 15
power cord set requirements 134
power cord, spare part
numbers 27, 32
power lights, identifying 7, 13
power requirements, product
description 4
power-on password 91
processor
product description 1
removal 85
spare part numbers 22, 85
Processor C4 State 91
product description
audio 3
camera 3
chipset 1
diskette drive 3
display panel 2
Ethernet 3
external media cards 4
graphics 2
hard drives 2
keyboard 4
memory module 2
microphone 3
modem module 3
operating system 4
optical drives 3
pointing devices 4
ports 4
power requirements 4
processors 1
product name 1
security 4
serviceability 4
wireless 3
product name 1
R
recovering a program or
driver 124
recovering from the dedicated
recovery partition 127
recovering from the recovery
discs 127
recovery 127
recovery discs 124, 126
Recovery Manager 124, 127
recovery partition 124
recovery, system 127
removal/replacement
preliminaries 33
procedures 39
restore points 125
restoring default settings 90
RJ-11 (modem) jack,
identifying 15
RJ-11 jack, pin assignments 131
RJ-45 (network) jack,
identifying 14
RJ-45 jack, pin assignments 131
RTC battery
removal 50
spare part number 21, 30,
50
rubber display kit, spare part
number 30
Rubber Feet Kit, spare part
number 23, 30, 40
S
Screw Kit
contents 106
screw kit, spare part number 31
screw listing 106
scrolling regions, TouchPad 6
secondary hard drive self test 92
security cable slot, identifying 14
Security menu 91
security, product description 4
selecting in the Setup Utility 89
serial number 17, 39
service considerations 33
serviceability, product
description 4
Setup Utility
Diagnostics menu 92
Main menu 91
overview 88
Security menu 91
starting 88
System Configuration
menu 91
slots
Digital Media 14
ExpressCard 14
memory module 16
security cable 14
solid-state drive (SSD) 124,
127
speaker assembly
removal 58
spare part number 19, 30,
58
speakers, identifying 8
specifications
computer 93
display 94
DVD/CD-RW Combo Drive 96
DVD±RW and CD-RW Combo
Drive 96
hard drive 95
I/O addresses 100, 102
interrupts 98, 99
memory map 104
optical drive 96
system DMA 97
static-shielding materials 37
supported discs 126
switch cover
removal 56
spare part number 19, 31,
56
system board
removal 79
spare part numbers 19, 30,
32, 79
System Configuration menu 91
system DMA 97
system failure or instability 124
system fan
removal 86, 87
spare part numbers 86
system information 91
system memory map 104
system recovery 127
system restore points 124, 125
T
thermal paste, replacement 83
tools required 33
top cover
removal 67
spare part number 19, 31,
67
TouchPad
buttons 6
identifying 6
removal 70
scrolling regions 6
spare part number 32
TouchPad bracket, spare part
number 32
TouchPad button board
spare part number 70
TouchPad button board, spare part
number 32
TouchPad light, identifying 6
TouchPad on/off button 6
transporting guidelines 36
U
Universal Serial Bus (USB) port, pin
assignments 132
unknown password 38
Index 145
USB board
removal 75
spare part number 20, 30,
75
USB board cable, spare part
number 30
USB ports, identifying 15
using system restore 125
V
vents, identifying 15, 16
Virtualization Technology 91
volume down light, identifying 7
volume mute button, identifying 9
volume mute light, identifying 7
volume scroll zone, identifying 9
volume up light, identifying 8
W
webcam light, identifying 11
webcam, identifying 11
Windows applications key,
identifying 10
Windows logo key, identifying 10
wireless antenna
removal 64
spare part number 65
Wireless Antenna Kit, spare part
number 65
wireless button, identifying 9
wireless light, identifying 7
wireless, product description 3
WLAN module
removal 47
spare part numbers 20, 29,
31, 47
workstation guidelines 36
146 Index