Yamaha YSP-1100 Owner`s manual

English
Connecting external components to this unit
Connect external component such as a TV or DVD player to this unit.
Connect your TV or DVD player to this unit using appropriate cables as shown below. Connecting a subwoofer enhances bass sound for listening enjoyment.
For further information on connecting other components, see pages 15 to 22 in the Owner’s Manual.
YSP-1100 QUICK REFERENCE GUIDE
DVD player
Cables used for connections
Connect cables in the following order. For the connection 2, use
either (a) or (b). If your DVD player has component video output
jacks, we suggest using the cable (b).
TV
This quick reference guide explains steps to connect a TV and a DVD player to this unit and achieve the
surround sound effects in a quick, easy manner. For detailed operation, refer to the Owner’s Manual.
Coaxial
digital
output
Video
output
Component
video
output
Optical
digital
output
Analog
audio
output
R
L
Video
input
Component
video
input
Installing this unit
1
2a
2b
3
Decide where to install this unit.
4
5
6
Install this unit where there are no objects such as furniture obstructing the path of sound beams. Otherwise, the desired surround
sound effects may not be achieved. You may install this unit in parallel with the wall or in the corner.
Install this unit in the exact center of the wall when it is
measured from the left and right corners.
An object, such as furniture
Subwoofer
Install this unit in the corner at a 40˚ to 50˚ angle from
the adjacent walls.
7
Monaural
input
An object, such as furniture
COMPONENT
COMPONENT
COMPONENT
DVD
COAXIAL
RS-232C
REMOTE IN
AUX
TV/STB
OPTICAL
DIGITAL IN
TV/STB VCR
AUDIO IN
VCR
SUBWOOFER
DVD/AUX
VIDEO IN
・Do not plug the power
supply cable into a wall
outlet until all connections
are complete.
・Unplug the power supply
cable before changing
connections, moving or
cleaning this unit.
y
If a subwoofer is connected to this unit, turn on the
power of your subwoofer and then carry out the
AUTO SETUP procedure (see the backside) or
select “SWFR” for “BASS OUT” in “SUBWOOFER
SET” (see page 67 in the Owner’s Manual).
8
This unit
40˚ to 50˚
CAUTION
1 Digital audio pin cable (supplied)
2a Video pin cable
2b Component video pin cable
3 Optical cable (supplied)
4 Audio pin cable (supplied)
5 Video pin cable (supplied)
6 Component video pin cable
(in case of a component connection)
7 Subwoofer pin cable
(in case you connect a subwoofer)
8 Power supply cable (supplied)
To the AC
outlet
STB
VIDEO OUT
Setting up the listening environment automatically
Connect the optimizer microphone to this unit.
You can automatically adjust the various channel settings that best match your listening environment using the supplied optimizer microphone. Follow the procedure below to connect the optimizer microphone to this unit and place it in a proper location.
Install this unit either above or under your TV.
Connect the optimizer microphone to the OPTIMIZER MIC jack on the left side of this unit.
Please read the following for reference. For further information on installation, see pages 11 and 13 in the Owner’s Manual.
Make sure you use the supplied fasteners to prevent an accidental fall of this unit (see page 14 in the Owner’s Manual).
When installing this unit above your TV, place it on
the top panel of a commercially available rack as
shown below.
Make sure that the top panel of the rack is wide and
stable enough to support the weight of this unit.
When installing this unit under your TV, place it in a
TV cabinet as shown below.
Make sure that the cabinet is large enough to allow
adequate ventilation space around this unit.
To enjoy better surround effects, place this unit
on the upper shelf to keep it away from the floor.
Cardboard microphone stand (supplied)
Assemble the cardboard microphone stand and place the
optimizer microphone on the top of the stand.
Optimizer microphone (supplied)
Set the optimizer microphone at your normal listening position. Use the supplied cardboard microphone stand or a tripod to place the optimizer microphone at the
same height as your ears would be when you are seated.
Place the optimizer microphone on the extended center
line of this unit and 1.8 m (6.0 ft) or more away from it.
Also, make sure place the optimizer microphone within
1 m (3.3 ft) upper or lower from the center height of this
unit.
Optimizer
microphone
Within 1 m (3.3 ft)
upper or lower
from the center
More than
1.8 m (6.0 ft)
Cardboard
microphone
stand
Printed in Malaysia
WH90290
Sofa
Center line
Optimizer
microphone
If you have set the optimizer microphone,
follow the steps on the backside to start
the AUTO SETUP procedure.
C2006
Continued
on the back
All rights reserved.
Continued
from the front
Carry out the AUTO SETUP (IntelliBeam) procedure to adjust the settings that
best match your listening environment.
Enjoying surround sound
This unit employs the YAMAHA IntelliBeam technology with the aid of the supplied optimizer microphone, allowing you to achieve highly accurate sound adjustments
that best match your listening environment. Be advised that it is normal for loud test tones to be output during the AUTO SETUP procedure. Make sure that there are
no children around in the listening room while the AUTO SETUP procedure is in progress.
Enjoy TV or DVD audio in surround sound.
1
6
Press STANDBY/ON on
the remote control.
STANDBY/ON
POWER POWER
AV
・Is the optimizer microphone firmly connected to this unit?
・Is the optimizer microphone placed in a proper loacation?
・Are there any large obstacles in between the optimizer microphone and the
walls in your listening room?
・The AUTO SETUP procedure starts in 10 seconds after pressing ENTER
on step 7. To achieve the best results possible, evacuate yourself for your
listening room until the AUTO SETUP procedure is completed.
・To cancel the AUTO SETUP procedure after it is started, press RETURN.
・The AUTO SETUP procedure takes about 3 minutes.
TV
The power of this unit turns on.
STB
VCR
DVD
AUX
TV
If a subwoofer with adjustable volume and
crossover/high cut frequency controls is
connected to this unit, set the volume
between 11 and 1 o’clock as viewed on a
conventional clockface and set the
crossover/high cut frequency to the
maximum.
CROSSOVER/
HIGH CUT
VOLUME
MIN
MAX
MIN
For instructions on your TV or DVD player, refer to the owner’s manual supplied with each component.
Before carrying out the procedure below, set the volume of this unit to 30. If necessary, adjust the volume level in
step 4.
Check the following points.
Enjoying TV in surround sound
1
Select the TV channel using
the remote control supplied
Enjoying DVDs in surround sound
1
Select the DVD video input on your
TV.
with your TV.
MAX
Subwoofer
2
2
Turn on the power of your TV.
7
CH LEVEL
TV/AV
Press ENTER to start the AUTO SETUP procedure.
ENTER
YSP
CH LEVEL
Select the appropriate video input
on your TV.
MENU
AUTO SETUP START
Will begin in 10sec
TV/AV
Please leave the room
ENTER
YSP
RETURN
TEST
3
**-------[RETURN]:Cancel
Press TV on the remote
control of this unit.
This unit switches to the TV playback mode.
4
The setup screen automatically changes during the AUTO SETUP
procedure.
If any error occurs, the corresponding error message appears on the screen.
In this case, see “Error messages for AUTO SETUP” on page 35 in the
Owner’s Manual and then follow the instructions. To start the AUTO SETUP
procedure once again, press RETURN and then carry out the procedure from
step 5.
Set the operation mode selector to YSP.
CH LEVEL
MENU
RETURN
TEST
The following screen appears on the TV and the AUTO SETUP procedure
starts in 10 seconds.
3
MENU
Set the operation mode selector to YSP .
INPUT1
3
Press DVD on the remote control of this unit,
and then start playback on the DVD player.
This unit switches to the DVD playback mode.
TV
INPUT2 MACRO
STB
VCR
TV
INPUT1
AUTO
VOL MODE SETUP INPUTMODE SLEEP
DVD
AUX
TV
INPUT2 MACRO
TV
AUTO
VOL MODE SETUP INPUTMODE SLEEP
When the AUTO SETUP procedure is complete, the following screen
appears on the TV.
TV/AV
ENTER
YSP
TEST
RETURN
SHOW RESULT
MEASUREMENT COMPLETE
BEAM MODE :5 BEAM
SUBWOOFER:NOT APPLICABLE
* This is an example of the result screen.
4
The result may differ depending on the
environment.
If you hear sound output from your TV speakers, turn down the volume level
until you cannot hear any sound.
Use the remote control supplied with your TV.
[ENTER]:Save set-up.
[RETURN]:Do not save set-up.
5
Press and hold AUTO SETUP for more than 2
seconds.
The menu screen appears on the TV.
If the menu screen does not appear, check the video pin cable (connection
5 in the diagram on the front page) is connected properly and then press
YSP followed by MENU.
STB
VCR
DVD
AUX
TV
INPUT2 MACRO
INPUT1
TV
AUTO
VOL MODE SETUP INPUTMODE SLEEP
5BEAM
ST+3BEAM
3BEAM
1
2
3
AUTO SETUP
PREPARATION & CHECK
Please connect the MIC.
Please place the MIC at least
1.8m/6ft away from the YSP
unit. The MIC should be set
at ear level when seated.
Measurement takes about 3min.
After [ENTER] is pressed,
please leave the room.
[ENTER]:Start [RETURN]:Cancel
5
8
VOLUME
CH
TV VOL
MUTE
TV INPUT
TV MUTE
5BEAM
ST+3BEAM
3BEAM
1
2
3
Press VOLUME +/– on the remote control to adjust
the volume level of this unit.
Press ENTER.
The result is confirmed and the following screen appears on the TV for 2
seconds and then the menu screen disappears from the TV.
The new settings are automatically saved in the system memory.
Disconnect the optimizer microphone and keep it in a safe place.
CH LEVEL
MENU
AUTO SETUP COMPLETE
TV/AV
ENTER
YSP
TEST
Please remove the MIC from
the YSP and the listening
position.
6
Press one of the beam mode buttons on the
remote control to select the desired beam mode.
Select one of the three beam modes that best matches the current input source of
this unit.
For further information on the beam modes, see page 42 in the Owner’s Manual.
STEREO
MY BEAM SURROUND
4
5
6
MUSIC
MOVIE
SPORTS
7
8
9
RETURN
To fine-tune the listening environment parameters manually or make advanced settings for
speaker positions, sound beams, etc., see “MANUAL SETUP” on page 60 in the Owner’s Manual.