Samsung CLP-300N Service manual

Color Laser Printer
CLP-300/XSG
Basic Model : CLP-300
Manual
Samsung Color Laser Printer
The keynote of Product
[The keynote of Product]
[Series Model]
.CLP-300: B/W 16 ppm, Color 4 ppm, SPL-C
.CLP-300N: CLP-300 + Network
[Resolution]
. 2400 x 600 dpi
[CPU]
.Samsung CorrusM 170MHz
[Interface]
.CLP-300 : USB 2.0
.CLP-300N : USB 2.0, Ethernet 10/100 Base TX
[Consumables]
.2K black toner cartridge
.1K color toner cartridge
.Waste toner box
[Paper Handling]
.150 sheets Semi-cassette
.1 sheet manual slot
.150 sheet Face-Down
Contents
Continued
Continued
Continued
1. Precautions
In order to prevent accidents and to prevent damage to the equipment please read the precautions listed
below carefully before servicing the printer and follow them closely.
1.1 Safety Warning
(1) Only to be serviced by appropriately qualified service engineers.
High voltages and lasers inside this product are dangerous. This printer should only be serviced by a suitably
trained and qualified service engineer.
(2) Use only Samsung replacement parts
There are no user serviceable parts inside the printer. Do not make any unauthorized changes or
additions to the printer, these could cause the printer to malfunction and create electric shock or fire hazards.
(3) Laser Safety Statement
The Printer is certified in the U.S. to conform to the requirements of DHHS 21 CFR, chapter 1 Subchapter J for
Class 1(1) laser products, and elsewhere, it is certified as a Class I laser product
conforming to the requirements of IEC 825. Class I laser products are not considered to be hazardous. The
laser system and printer are designed so there is never any human access to laser radiation above a Class I
level during normal operation, user maintenance, or prescribed service condition.
Service Manual
Samsung Electronics
1.2 Caution for safety
1.2.1 Toxic material
1.2.2 Electric Shock and Fire Safety Precautions
Failure to follow the following instructions could cause electric shock or potentially cause a fire.
(1) Use only the correct voltage, failure to do so could damage the printer and potentially cause a fire or electric
shock.
(2) Use only the power cable supplied with the printer. Use of an incorrectly specified cable could cause the cable
to overheat and potentially cause a fire.
(3) Do not overload the power socket, this could lead to overheating of the cables inside the wall and could lead to
a fire.
(4) Do not allow water or other liquids to spill into the printer, this can cause electric shock. Do not allow paper
clips, pins or other foreign objects to fall into the printer these could cause a short circuit leading to an electric
shock or fire hazard..
(5) Never touch the plugs on either end of the power cable with wet hands, this can cause electric shock. When
servicing the printer remove the power plug from the wall socket.
(6) Use caution when inserting or removing the power connector. The power connector must be inserted completely otherwise a poor contact could cause overheating possibly leading to a fire. When removing the power
connector grip it firmly and pull.
(7) Take care of the power cable. Do not allow it to become twisted, bent sharply round corners or otherwise
damaged. Do not place objects on top of the power cable. If the power cable is damaged it could overheat and
cause a fire or exposed cables could cause an electric shock. Replace a damaged power cable immediately,
do not reuse or repair the damaged cable. Some chemicals can attack the coating on the power cable,
weakening the cover or exposing cables causing fire and shock risks.
(8) Ensure that the power sockets and plugs are not cracked or broken in any way. Any such defects should be
repaired immediately. Take care not to cut or damage the power cable or plugs when moving the machine.
(9) Use caution during thunder or lightening storms. Samsung recommend that this machine be disconnected from
the power source when such weather conditions are expected. Do not touch the machine or the power cord if it
is still connected to the wall socket in these weather conditions.
(10) Avoid damp or dusty areas, install the printer in a clean well ventilated location. Do not position the machine
near a humidifier. Damp and dust build up inside the machine can lead to overheating and cause a fire.
(11) Do not position the printer in direct sunlight. This will cause the temperature inside the printer to rise possibly
leading to the printer failing to work properly and in extreme conditions could lead to a fire.
(12) Do not insert any metal objects into the machine through the ventilator fan or other part of the casing, it could
make contact with a high voltage conductor inside the machine and cause an electric shock.
Service Manual
Samsung Electronics
1.2.3 Handling Precautions
The following instructions are for your own personal safety, to avoid injury and so as not to damage the printer
(1) Ensure the printer is installed on a level surface, capable of supporting its weight. Failure to do so could cause
the printer to tip or fall.
(2) The printer contains many rollers, gears and fans. Take great care to ensure that you do not catch your fingers,
hair or clothing in any of these rotating devices.
(3) Do not place any small metal objects, containers of water, chemicals or other liquids close to the printer which if
spilled could get into the machine and cause damage or a shock or fire hazard.
(4) Do not install the machine in areas with high dust or moisture levels, beside on open window or close to a
humidifier or heater. Damage could be caused to the printer in such areas.
(5) Do not place candles, burning cigarettes, etc. on the printer, these could cause a fire.
1.2.4 Assembly / Disassembly Precautions
Replace parts carefully, always use Samsung parts. Take care to note the exact location of parts and also
cable routing before dismantling any part of the machine. Ensure all parts and cables are replaced correctly.
Please carry out the following procedures before dismantling the printer or replacing any parts.
(1) Check the contents of the machine memory and make a note of any user settings. These will be erased if the
mainboard is replaced.
(2) Ensure that power is disconnected before servicing or replacing any electrical parts.
(3) Disconnect printer interface cables and power cables.
(4) Only use approved spare parts. Ensure that part number, product name, any voltage, current or temperature
rating are correct.
(5) When removing or re-fitting any parts do not use excessive force, especially when fitting screws into plastic.
(6) Take care not to drop any small parts into the machine.
(7) Handling of the OPC Drum
- The OPC Drum can be irreparably damaged if it exposed to light.
Take care not to expose the OPC Drum either to direct sunlight or to fluorescent or incandescent room
lighting. Exposure for as little as 5 mins can damage the surface’s photoconductive properties and will result
in print quality degradation. Take extra care when servicing the printer. Remove the OPC Drum and store it in
a black bag or other lightproof container. Take care when working with the covers(especially the top cover)
open as light is admitted to the OPC area and can damage the OPC Drum.
- Take care not to scratch the green surface of OPC Drum Unit.
If the green surface of the Drum Cartridge is scratched or touched the print quality will be compromised.
Service Manual
Samsung Electronics
1.2.5 Disregarding this warning may cause bodily injury
(1) Be careful with the high temperature part.
The fuser unit works at a high temperature. Use caution when working on the printer. Wait for the fuser to cool
down before disassembly.
(2) Do not put finger or hair into the rotating parts.
When operating a printer, do not put hand or hair into the rotating parts (Paper feeding entrance, motor, fan,
etc.). If do, you can get harm.
(3) When you move the printer.
This printer weighs 13.6kg including Consumables. Use safe lifting and handling techniques. Back injury could
be caused if you do not lift carefully.
(4) Ensure the printer is installed safely.
The printer weighs 13.6Kg, ensure the printer is installed on a level surface, capable of supporting its weight.
Failure to do so could cause the printer to tip or fall possibly causing personal injury or damaging the printer.
(5) Do not install the printer on a sloping or unstable surface. After installation, double check that the printer is stable.
Service Manual
Samsung Electronics
1.3 ESD Precautions
Certain semiconductor devices can be easily damaged by static electricity. Such components are commonly called
“Electrostatically Sensitive (ES) Devices”, or ESDs. Examples of typical ESDs are: integrated circuits, some field
effect transistors, and semiconductor “chip” components.
The techniques outlined below should be followed to help reduce the incidence of component damage caused by
static electricity.
1. Immediately before handling a semiconductor component or semiconductor-equipped assembly, drain off any
electrostatic charge on your body by touching a known earth ground. Alternatively, employ a commercially available wrist strap device, which should be removed for your personal safety reasons prior to applying power to the
unit under test.
2. After removing an electrical assembly equipped with ESDs, place the assembly on a conductive surface, such as
aluminum or copper foil, or conductive foam, to prevent electrostatic charge buildup in the vicinity of the assembly.
3. Use only a grounded tip soldering iron to solder or desolder ESDs.
4. Use only an “anti-static” solder removal device. Some solder removal devices not classified as “anti-static” can
generate electrical charges sufficient to damage ESDs.
5. Do not use Freon-propelled chemicals. When sprayed, these can generate electrical charges sufficient to damage ESDs.
6. Do not remove a replacement ESD from its protective packaging until immediately before installing it. Most
replacement ESDs are packaged with all leads shorted together by conductive foam, aluminum foil, or a comparable conductive material.
7. Immediately before removing the protective shorting material from the leads of a replacement ESD, touch the protective material to the chassis or circuit assembly into which the device will be installed.
8. Maintain continuous electrical contact between the ESD and the assembly into which it will be installed, until completely plugged or soldered into the circuit.
9. Minimize bodily motions when handling unpackaged replacement ESDs. Normal motions, such as the brushing
together of clothing fabric and lifting one’s foot from a carpeted floor, can generate static electricity sufficient to
damage an ESD.
1.4 Super Capacitor or Lithium Battery Precautions
1. Exercise caution when replacing a super capacitor or Lithium battery. There could be a danger of explosion and
subsequent operator injury and/or equipment damage if incorrectly installed.
2. Be sure to replace the battery with the same or equivalent type recommended by the manufacturer.
3. Super capacitor or Lithium batteries contain toxic substances and should not be opened, crushed, or burned for
disposal.
4. Dispose of used batteries according to the manufacture’s instructions.
Service Manual
Samsung Electronics
Product Specifications
2. Product Specifications
2.1 Product Overview
* Average A4-/letter-sized page count based on Standard coverage of individual colors on each page.
Usage conditions and print patterns may cause results to vary.
** Image counts based on one color on each page. If you print documents in full color (Cyan, Magenta,
Yellow, Black), the life of this item will be reduced by 25%.
Service Manual
Samsung Electronics
Product Specifications
2.2 Specifications
2.2.1 General Specifications
Service Manual
Samsung Electronics
Product Specifications
2.2.2 Controller & S/W
Service Manual
Samsung Electronics
Product Specifications
2.2.3 Paper Handling
Service Manual
Samsung Electronics
Product Specifications
2.2.4 Consumables
Service Manual
Samsung Electronics
Product Specifications
2.2.5 Environment
2.2.6 Options
2.2.7 Accessory
Service Manual
Samsung Electronics
Product Specifications
2.3 Model Comparison Table
Service Manual
Samsung Electronics
System Overview
3. System Overview
This chapter describes the functions and operating principles of the main components.
3.1 System Structure
Service Manual
Samsung Electronics
System Overview
Service Manual
Samsung Electronics
System Overview
Service Manual
Samsung Electronics
System Overview
Service Manual
Samsung Electronics
System Overview
Service Manual
Samsung Electronics
System Overview
Service Manual
Samsung Electronics
System Overview
Service Manual
Samsung Electronics
System Overview
Service Manual
Samsung Electronics
System Overview
Service Manual
Samsung Electronics
System Overview
Service Manual
Samsung Electronics
System Overview
Service Manual
Samsung Electronics
System Overview
Service Manual
Samsung Electronics
System Overview
Service Manual
Samsung Electronics
System Overview
Service Manual
Samsung Electronics
System Overview
Service Manual
Samsung Electronics
System Overview
Service Manual
Samsung Electronics
System Overview
Service Manual
Samsung Electronics
System Overview
Service Manual
Samsung Electronics
System Overview
Service Manual
Samsung Electronics
System Overview
* Average A4-/letter-sized page count based on ISO 19752 Standard coverage of individual colors on each page. Usage
conditions and print patterns may cause results to vary.
** Image counts based on one color on each page. If you print documents in full color (Cyan, Magenta, Yellow, Black), the life
of this item will be reduced by 25%.
Service Manual
Samsung Electronics
System Overview
Service Manual
Samsung Electronics
4. S/W Structure and Descriptions
4.1 Architecture
The belt CRUM interface board is a transmission belt CRUM interface board of the photoelectric Dry Color Laser
Printer, mounted on the printer body, making it possible to physically combine the body and the belt CRUM board.
4.2 Language Monitor
Language Monitor is a part of the Printer Driver and the Windows Spool System. The main roll of the Language
Monitor is that sends a job start message to the Status Monitor. Therefore the Status Monitor
can start polling to get the printer status.
The second roll is that sends the job information such as User ID and Job ID to the Status Monitor and the Printer
F/W. Hence the Status Monitor can stop polling because the Printer F/W informs the Status Monitor that printing
job is complete.
4.3 Status Monitor
Status Monitor has no user interface. It shows only HTML help when any error occurs during printing jobs.
Service Manual
Samsung Electronics
4.4 Network Interface
After polling is started, Status Monitor has to know when it stops the polling. For this reason, the Network
Printer Server should inform of completing job when the printing job is finished.
When Status Monitor requests a job status, the Printer Server returns the job table that contains user id, job
id, and job status (printing or complete or canceled).
4.5 Printer Driver <-> Status Monitor
The Printer Driver and the Status Monitor can set/get some data to the system registry to share the Status Monitor
information such as the polling interval.
When the user wants to set the option of the Status Monitor manually, he or she can set it using the Printer Driver
User Interface. So, if the user set option that the Status Monitor is disabled, the Status Monitor can’s show HTML
Help to the user although the error has occurred while printing.
Service Manual
Samsung Electronics
4.6 System F/W Flow
Service Manual
Samsung Electronics
4.7 Alarm Shortage
4.8 Error status
1. Missing/Invalid Consumables
Install Cyan (Magenta, Yellow, Black) Toner
Install Transfer Belt
Invalid Cyan (Magenta, Yellow, Black) Toner
Invalid Transfer Belt
2. Paper Empty/Mismatch
Paper Empty In MP(Tray1, Tray2)
Load A4 In MP(Tray1, Tray2)
3. Paper JAM
Jam 0 In MP(Tray1, Tray2)
Jam Inside Printer
Jam In Exit Area
4. Cover
Cover Open : Message toggles between
Cover Open and Install Transfer Belt
SCF Cove Open
5. Service Call : Unrecoverable Error
Engine LSU Error
Main Motor Error / Dev. Motor Error
Engine Fuser Over(Low) Heat Error
Rear Fan Error / Left Fan Error / SMPS Fan Error
6. Others
Memory Overflow Error
Ready IP Conflict
Service Manual
Samsung Electronics
4.9 CRUM Overview
- Stands for “Customer Replaceable Unit Monitor”
- EEPROM is used for CRUM Memory.
- CRUM stores various information on consumables
(including consumables’ life).
- In CLP600, total five CRUM’s are used
(four on toner cartridges and one on transfer belt)
CRUM stores the following information
Model Name
Supplier ID
Serial Number
Company ID
MFG Date
Capacity
Page Count
- Toner Cartridge and Transfer Belt
- Indicates how many pages are printed by using the consumable
Dot Count
- Toner Cartridge Only
- Indicates how many dots are printed by using the toner cartridge
4.10 FW Upgrade
Via USB or Network (SWS/SWAS)
You can upgrade F/W via USB or Network whenever the printer is “Ready”
Via Using F/W Download Mode :
Step 1) Power on while pressing the Online Key
Step 2) Press Online Key one more time if “Press Key Again” is displayed on LCD
Step 3) Download F/W via USB
Service Manual
Samsung Electronics
4.11 Initailize Flow
Service Manual
Samsung Electronics
Service Manual
Samsung Electronics
5. Disassembly and Reassembly
5.1 Precautions When Replacing Parts
5.1.1 Precautions when assembling and disassembling
5.1.2 Precautions when handling PBA
page(5-2)
page(5-2)
page(5-2)
5.2 Parts for Maintenance and Repair
5.2.1 Replacement interval for parts with a limited life
5.2.2 Printer Cleaning
page(5-3)
page(5-3)
page(5-4)
5.3 Information Related in Disassembly and Assembly
5.3.1 Special Service Parts
1) Disassemble of LSU Unit
2) Disassemble of ITB Unit
3) Custody of OPC Unit
4) Custody of Toner Cartridge
5) Disassemble of DEVE Drive Ass’y and Main Drive Ass’y
6) Disassemble of Terminal Parts
7) Disassemble of Fuser Unit
5.3.2 Screws Used in the Printer
5.3.3 Opening Covers and replacing Consumable parts
>> Consumable parts removal
page(5-5)
page(5-5)
page(5-5)
page(5-5)
page(5-5)
page(5-5)
page(5-5)
page(5-5)
page(5-5)
page(5-6)
page(5-10)
page(5-10)
5.4 Disassembly Procedure
5.4.1 Cover Unit
5.4.2 Fuser Ass’y
5.4.3 LSU(Laser Scan Unit)
5.4.4 HVPS(High Voltage Power Supply
5.4.5 Main Board
5.4.6 SMPS(Switching Mode Power Supply)
5.4.7 Drive Ass’y
5.4.8 Transfer Roller
page(5-10)
page(5-10)
page(5-11)
page(5-12)
page(5-12)
page(5-13)
page(5-13)
page(5-14)
page(5-14)
Service Manual
Samsung Electronics
5.1 Precautions when replacing parts
5.1.1 Precautions when assembling and disassembling
* Use only approved Samsung spare parts. Ensure that part number, product name, any voltage, current or
temperature rating are correct. Failure to do so could result in damage to the machine, circuit overload,
fire or electric shock.
* Do not make any unauthorized changes or additions to the printer, these could cause the printer to malfunction and create electric shock or fire hazards.
* Take care when dismantling the unit to note where each screw goes. There are 19 different screws. Use of
the wrong screw could lead to system failure, short circuit or electric shock.
* Do not disassemble the LSU unit. Once it is disassembled dust is admitted to the mirror chamber and will
seriously degrade print quality. There are no serviceable parts inside.
* Regularly check the condition of the power cord, plug and socket. Bad contacts could lead to overheating
and firfe. Damaged cables could lead to electric shock or unit malfunction.
5.1.2 Preautions when handling PBA
Static electricity can damage a PBA, always used approved anti-static precautions when
handling or storing a PBA.
>> Precautions when moving and storing PBA
1. Please keep PBA in a conductive case, anti-static bag, or wrapped in aluminum foil.
2. Do not store a PBA where it is exposed to direct sunlight.
>> Precautions when replacing PBA
1. Disconnect power connectors first, before disconnecting other cables
2. Do not touch any soldered connections, connector terminals or other electronic parts when handling
insulated parts.
>> Precautions when checking PBA
1. Before touching a PBA, please touch other grounded areas of the chassis to discharge any static electrical charge on the body.
2. Take care not to touch the PBA with your bare hands or metal objects as you could create a short circuit or get an electric shock. Take extra care when handling PBAs with moving parts fitted such as sensors, motors or lamps as they may get hot.
3. Take care when fitting, or removing, screws. Look out for hidden screws. Always ensure that the correct
screw is used and always ensure that when toothed washers are removed they are refitted in their original positions.
5.1.3 Releasing Plastic Latches
Many of the parts are held in place with plastic latches. The latches break easily; release them carefully.
To remove such parts, press the hook end of the latch away from the part to
which it is latched.
Service Manual
Samsung Electronics
5.2 Parts for Maintenance and Repair
5.2.1 Replacement interval for parts with a limited life
Some of the parts in this printer have a limited life, shorter than that of the whole machine. These parts
must be replaced periodically.
The table below shows the interval at which these parts should be replaced.
The table shows the life of each part, and is measured when using A4 paper. When servicing a machine
always check the status of these parts using the control panel and ensure that parts are replaced at the
appropriate times otherwise a general degradation in print quality will occur.
* Average A4-/letter-sized page count based on ISO 19752 Standard coverage of individual colors on each page.
Usage conditions and print patterns may cause results to vary.
** Image counts based on one color on each page. If you print documents in full color (Cyan, Magenta, Yellow, Black), the life
of this item will be reduced by 25%.
Service Manual
Samsung Electronics
5.2.2 Printer Cleaning
A printer should be regularly cleaned, especially if it is used in a dusty environment. This will ensure that
print quality remains high and failure due to contamination of printing services is less likely to occur.
* Clean the printer with a soft, lint free, cloth dipped in a "Recommended cleaner"
"Recommended cleaner" can be purchased from our service center. (where available)
* Do not touch the transfer roller when cleaning the inside of the printer. Grease and oils from the
skin will contaminate the surface and reduce print quality.
* Do not touch transfer roller when cleaning inside of machine. If transfer roller gets dirty, printing
quality could be low.
* Please refer to the User Manual for cleaning instructions.
Service Manual
Samsung Electronics
5.3 Information Related to Disassembly and Assembly.
5.3.1 Special service parts
Never disassemble or adjust the items mentioned, a stock of these items should be maintained.
1) Disassembly of the LSU unit
There are no serviceable parts inside the
LSU. Alignment of the mirrors is critical.
Opening the LSU will allow dust into the
laser and significantly reduce print quality.
It is very dangerous to operate or service
a machine with the LSU open or system
interlocks disabled. Exposure to laser
radiation can cause blindness.
2) Disassembly of the ITB unit
Do not disassemble the ITB. The alignment of the home sensor is critical and is
set up in the factory on a special jig.
Incorrect re-assembly will cause print
quality degradation.
3) Care of the Toner cartridge
Toner cartridges contain an extremely fine
powder. Please keep toner cartridges
away from children. The toner powder
contained in the toner cartridge may be
harmful and if swallowed you should contact a doctor. Take care not to spill toner spillages should be cleaned with a
vacume cleaner and washed in could
water (hot water sets the toner). Do not
touch the developer roller surface as contamination will reduce print quality. Take
care not to damage the roller's surface
when installing or removing a toner cartridge.
4) Disassembly of DEVE drive ass'y
and the main drive ass'y
The alignment of the drive mechanism is
critical and it has been set up in factory
using a jig and a driving gear. It is adjusted for the best gearing alignment. If the
motor is disassembled alignment would
not be maintained and this could cause
operational noise and image problems:
image alignment and toner distribution
may be affected.
5) Disassembly of terminal parts
Do not adjust the variable resistors on the
PBA. They have been already adjusted in
the factory.
6) Disassembly of the fuser unit
- The fuser melts toner onto the paper at
a high temperature: therefore, you need
to take special care not to get burned by
a hot fuser. When removing the fuser
from a set that has recently been operating you need to take extra care.
- Do not touch an AC line (Copper contact) on a main frame even after removing the fuser.
7) When you replace ITB Unit,
be careful with following things;
- When you replace ITB Unit, carefully handle
with ITB Belt. If not, it harms ITB Belt.
- Do not turn ITB Belt back and forth.
If not, waste toner powder would be leaked.
- When shutter is working on an outlet of
waste toner, be careful that waste toner
powder would be leaked
Service Manual
Samsung Electronics
5.3.2 Screws used in the printer
The screws listed in the table below are used in this printer. Please ensure that, when
you disassemble the printer, you keep a note of which screw is used for which part and
that, when reassembling the printer, the correct screws are used in the appropriate
places.
Service Manual
Samsung Electronics
Service Manual
Samsung Electronics
Service Manual
Samsung Electronics
Service Manual
Samsung Electronics
5.4 Disassembly Procedure
5.4.1 Cover Unit
Service Manual
Samsung Electronics
5.4.2 Fuser Ass’y
Service Manual
Samsung Electronics
5.4.3 LSU(Laser Scan Unit)
5.4.4 HVPS(High Voltage Power Supply)
Service Manual
Samsung Electronics
5.4.5 Main Board
5.4.6 SMPS(Switching Mode Power Supply)
Service Manual
Samsung Electronics
5.4.7 Drive Ass’y
5.4.8 Transfer Roller
Service Manual
Samsung Electronics
Alignment and Adjustmens
6. Alignment and Adjustments
This chapter describes some of the main service procedures including:
Using the EDC mode; Clearing paper jam and test patterns.
Much of this chapter is also included in the user's guide.
6.1. Control Panel
- The CLP-300 printers do not have LCD panel which is used in other color model printers. On the contrary
to other models of color printers, they show the status of the printer only with their LEDs.
- The CLP-300 printers have 2 keys and 6 LEDs. The ‘User Interface’ module handles the processing of the
‘Key Press’ and ‘Led control’ at different states of the machine.
KEY (2 key): Stop key, Black only key
LED (6 LEDs):
4 LED for CMYK toners : toner-low(cyan, magenta, yellow, black) LEDs
1 LED for status : ready (green) or error(red) status LED (two color LED)
1 LED for Black only: If Black only key is pressed, Black only led glows.
User interface (panel) is made up of
- KEY input detection & process
- LED control
The initial process to use the panel checks register°Øs values of key and LED.
If user input key value, the operation to be defined by key value is processed and the LED operation to be
defined by printer status is controlled.
Service Manual
Samsung Electronics
Alignment and Adjustmens
6.2 Function
There are two keys present. The one is Stop key and the other is Black only key.
If users input key value, the key input is transferred via GIP (General Input Port) and the operation to be
defined by key value is processed.
Stop key function is made up of
- Demo page/Configuration sheet printing function
- Job cancels function
- Start manual feeding function
- Firmware downloads mode function
Black only key function is made up of
- Change printer mode to Black-only mode function
- Black only LED light function
KEY input detection & process order
1) User KEY input
2) KEY input detection
: If the key input is detected when the key input check per timer tick 10ms, The 10ms interrupt service
routine sends the key detection event to panel task.
3) KEY input process
Stop key input process
: After the panel task is received the Stop key detection event, it checks the engine error status two times
and process the operation to be defined by key value.
- Demo page/Configuration sheet function
This button will have multiple functions when the printer is in idle state.
Demo page printing
Press and hold this button for about 2 seconds until the control panel lights blink slowly to print a
demo page.
Configuration sheet printing
Press and hold this button for about 6 seconds until the control panel lights blink rapidly to print a configuration sheet.
- Job cancels function
When the printer is printing an active printing job, press and holds this button until the control panel
lights blink to cancel a job the printer is currently except the manual job.
- Start manual feeding function
When you select manual feed for paper source, press this button each time you feed a sheet of paper
manually.
The application of manual feeding function in CLP-300 will be determined
Service Manual
Samsung Electronics
Alignment and Adjustmens
- Firmware downloads mode function
Turn on the printer at the same time that the button is pressed.
If all LEDs scroll, release the button and download the firmware ROM file via USB port
Black only key input process
: After the panel task is received the Black only key detection event, it changes printer mode to Black only
mode and notifies driver that the printer mode is changed to Black only mode. If printer mode is Black
only mode, driver makes printer image by only mono excepting color and the Black only LED glows.
There are six LEDs present. Status led indicate the error/online status of the printer in idle mode. In error
mode, the status LED glows by red color and in ready mode, it glows by green color. The other four LEDs
indicate the toner status. If the black toner needs to change, the toner-low (black) LED glows and if the
color (yellow, magenta, cyan) toners need to change, the toner-low (yellow, magenta, cyan) LED glows.
Black only LED indicate the printer mode. If the users press the Black only button, the printer mode
changes to Black only mode and Black only LED glows.
LED function is made up of
- Ready/Printing status display
- Error status display
- Toner low status display
- Black only status display
LED control order
1) Control LED according to current printer state
: After the panel task is received each event, the LED operation is controlled by current printer status.
2) Write LED value to GOP (General Output Port)
Service Manual
Samsung Electronics
Alignment and Adjustmens
LED behavior
Service Manual
Samsung Electronics
Alignment and Adjustmens
Service Manual
Samsung Electronics
Alignment and Adjustmens
6.3 Jam Removal
When a jam occurs while printing a jam message is displayed on the control panel.
* Jam0 In Tray 1:
Paper jam in the main cassette.
* Jam0 In MP Tray:
Paper jam in the MP tray
* Jam Inside Printer:
Jam 1, Paper is jammed inside the printer.
* Jam In Exit Area:
Jam2, Paper is jammed in the exit area when ejecting paper.
CAUTION: When removing jammed paper, always pull it firmly and evenly without any sudden jerks. If
at all possible, remove the paper as a single sheet. If the paper tears ensures ALL paper
fragments are removed. Any fragments left inside the machine will cause it to jam again.
NOTE: When removing paper that is jammed in the printer, if possible always pull the paper in the direction
that it normally moves so as not to damage internal components. Always pull firmly and evenly; do
not jerk the paper. If the paper tears, ensure that all fragments of paper are removed; otherwise a
jam will occur again.
If a paper jam occurs, the Status LED on the control panel lights red. Find and remove the jammed paper.
To resume printing after clearing paper jams, you must open and close the front cover or rear cover.
1. To remove the jammed paper, open the rear
cover.
2. Carefully remove the paper by pulling in the
direction as shown below. Most of the jammed
paper can be removed in this step.
If you cannot find the jammed paper, or if there
is any resistance removing the paper, stop
pulling and go to the next step.
Service Manual
Samsung Electronics
Alignment and Adjustmens
3. Close the rear cover and then open the top
cover.
4. Holding the inner cover open, carefully take the
jammed paper out of the printer. The inner
cover will then close automatically.
5. Close the top cover. Make sure that it is
securely latched.
6. Open and then close the rear cover or front
cover to resume printing.
Service Manual
Samsung Electronics
Alignment and Adjustmens
By selecting the correct paper types, most paper jams can be avoided.
• Follow the procedures Jam remove. Ensure that the adjustable guides are positioned correctly.
• Do not overload the paper tray.
• Do not remove the paper from the tray while printing.
• Flex, fan, and straighten the paper before loading.
• Do not use creased, damp, or highly curled paper.
• Do not mix paper types in a tray.
• Use only recommended print materials.
• Ensure that the recommended print side of print materials is facing up in the paper tray.
Service Manual
Samsung Electronics
Alignment and Adjustmens
6.4 Sample Pattern
Service Manual
Samsung Electronics
Alignment and Adjustmens
Service Manual
Samsung Electronics
Alignment and Adjustmens
Samsung Electronics
Service Manual
Samsung Electronics
Alignment and Adjustmens
6.5 Periodic Defective Image
If an image defects appears at regular intervals on the printed-paper, it is due to a faulty or damaged roller.
Refer to the table below and check the condition of the appropriate roller.
Service Manual
Samsung Electronics
Alignment and Adjustmens
6.6 How to use EDC (Engine Diagnostic Control) Mode
Service Manual
Samsung Electronics
Alignment and Adjustmens
Service Manual
Samsung Electronics
Alignment and Adjustmens
Service Manual
Samsung Electronics
Alignment and Adjustmens
Service Manual
Samsung Electronics
Alignment and Adjustmens
Service Manual
Samsung Electronics
Alignment and Adjustmens
Service Manual
Samsung Electronics
Alignment and Adjustmens
6.7 Error Message
When the printer experiences an error, the control panel will indicate an error message with the indicator
lights and the Smart Panel program window will display to show the printer’s status or errors. Find the light
pattern below that matches the printer light pattern and follow the solutions to clear the error.
LED status legend
Service Manual
Samsung Electronics
Troubleshooting
7. Troubleshooting
7.1 Procedure of Checking the Symptoms
Service Manual
Samsung Electronics
Troubleshooting
7.2 Troubleshooting Checklist
Service Manual
Samsung Electronics
Troubleshooting
7.3 Solving General Printing Problems
Service Manual
Samsung Electronics
Troubleshooting
Service Manual
Samsung Electronics
Troubleshooting
Service Manual
Samsung Electronics
Troubleshooting
Service Manual
Samsung Electronics
Troubleshooting
7.4 Solving Print Quality Problems
AaBbCc
AaBbCc
AaBbCc
AaBbCc
AaBbCc
AaBbCc
AaBbCc
AaBbCc
AaBbCc
AaBbCc
Service Manual
Samsung Electronics
Troubleshooting
AaBbCc
AaBbCc
AaBbCc
AaBbCc
AaBbCc
AaBbCc
AaBbCc
AaBbCc
AaBbCc
AaBbCc
Service Manual
Samsung Electronics
Troubleshooting
Aa B b C
c
A a Bb C
c
Aa B b C
c
A a Bb C
c
A a Bb C
c
Service Manual
Samsung Electronics
Troubleshooting
AaBbCc
AaBbCc
AaBbCc
AaBbCc
AaBbCc
Service Manual
Samsung Electronics
Troubleshooting
7.5 Common Windows Problems
7.6 Common Macintosh Problems
Service Manual
Samsung Electronics
Troubleshooting
7.7 Common Linux Problems
Service Manual
Samsung Electronics
Troubleshooting
Service Manual
Samsung Electronics
Troubleshooting
Service Manual
Samsung Electronics
Troubleshooting
7.8 Major Problems Trouble shooting
7.8.1 Vertical Line and Band
7.8.2 Vertical White Line
Service Manual
Samsung Electronics
Troubleshooting
7.8.3 Light Image
7.8.4 Dark Image or black
Service Manual
Samsung Electronics
Troubleshooting
7.8.5 Background
7.8.6 JAM 0
Service Manual
Samsung Electronics
Troubleshooting
7.8.7 JAM 1
7.8.8 Multi-Feeding
7.8.9 Not function of the gear of the fuser due to melting away
Service Manual
Samsung Electronics
Troubleshooting
7.8.10 Paper Empty
7.8.11 Cover Open
7.8.12 Defective motor operation
Service Manual
Samsung Electronics
Troubleshooting
7.8.13 No Power
7.8.14 Vertical Line Getting Curved
7.8.15 LSU Error
Service Manual
Samsung Electronics
8. Exploded Views and Parts List
Contents
Service Manual
Samsung Electronics
9
10
7
11
12
16
28
0
13
20
2
8
24
21
3
25
22
19
1
26
6
18
27
4
23
15
17
5
14
8.1 Main
Service Manual
Samsung Electronics
8.2 Top Cover
0
3
8
11
9
7
10
2
4
6
1
5
12
Service Manual
Samsung Electronics
8.3 Rear Cover
0
2
7
1
5
4
9
9
8
3
6
8
10
Service Manual
Samsung Electronics
8.4 Front Cover
0
2
1
Service Manual
Samsung Electronics
12
1
13
14
3
4
2
18
5
2
9
16
15
7 10
6
8
19
17
7
21
20
11
27
22
25
26
23
27
24
0
31
30
37
29
28
34 35
33
36
32
8.5 Main Driver(1)
Service Manual
Samsung Electronics
45
44
48
49
47
52
42
50
42
41
46
49
40
47
43
39
28
38
23
49
11
Main Driver(2)
Service Manual
Samsung Electronics
35
32
29
34
1
33
4
2
30
31
5
3
17
3
26
2
21
28
20
27
25
6
24
7
23
19
7
22
8
8
11
10 12
8
9
17
13
11
16
18
14
15
0
8.6 Main Frame(1)
Service Manual
Samsung Electronics
0
43
40
42
41
39
38
37
Samsung Electronics
53
36
50
43
42
48
46
44
59
57
58-1
47
49
45
63
58-3
55
58-2
58
56
62
64
51
54
60
52
61
65
63
Main Frame(2)
Service Manual
8.7 LSU Cover
0
4
4
5
2
1
6
3
Service Manual
Samsung Electronics
Samsung Electronics
27
6
7
40
26
29
41
30
43
28
3
12
31
35
0
1
11
37
8
39
9
23
36
5
15
21
4
13
22
10
33
38
18
20
40
14
32
16
2
19
34
17
8.8 Fuser Unit
Service Manual
2
14
12
13
15
5
3
16
11
2
10
9
6
0
8.9 ELA-UNIT OPC DEV
Service Manual
Samsung Electronics
8.10 ITB Unit
29
61
9
64
17
13
9
72
60
26
21
14
6
6
31
19
6
51
25
6
76
46
27 55
40
23
45
33
34
37
36
6
15
38
43
6
30
58
54
65
32
39
52
18
6
59
42
62
8
22
16
56
7 7 24
39
28
44
20
37
38
57
41
35
6
68
48
49 47
10
27 7
40
53
0
5
8
50
6
6
Service Manual
Samsung Electronics
1
2
4
3
5
9
6
0
7
8
12
6
7
13
18
14
11
17
15
19
14
10
17
16
8.11 Casstte Unit
Service Manual
Samsung Electronics
Service Parts List (Model code : CLP-300/XSG)
SA : SERVICE AVAILABLE SNA : SERVICE not AVAILABLE DNA : DELIVERY not AVAILABLE
Drawer#
SEC-Code
Description & Specification
Location Service
8.1-1
JC97-02330A
MEA UNIT-FRAME;CLP-300,SEC,WORLD,-,-,-,Z4398
SA
8.1-2
JC63-00842A
COVER-M-LEFT SIDE;CLP-300,ABS FR,T2.5,23
Z4399
SA
8.1-3
JC63-00847A
COVER-M-DUMMY FRONT;CLP-300,ABS FR,T2.5,
Z4400
SA
8.1-4
JC63-01102B
SHEET-COVER TOP;CLP-300,PC SHEET,T0.5,W7
SA
8.1-6
JC96-03608A
ELA UNIT-DRIVE MAIN;CLP-300,SEC,WORLD,-,
Z4403
SA
8.1-7
JC96-03610F
ELA UNIT-OPC DEV_SET;CLP-300,SEC,EXPORT,
SA
8.1-8
JC96-03611A
ELA UNIT-ITB_SET;CLP-300,SEC,WORLD,SET,Z4404
SA
8.1-9
JC96-03615A
ELA UNIT-TONER TANK C;CLP-300,SEC,EXPORT
SNA
8.1-10
JC96-03614A
ELA UNIT-TONER TANK M;CLP-300,SEC,EXPORT
SNA
8.1-11
JC96-03613A
ELA UNIT-TONER TANK Y;CLP-300,SEC,EXPORT
SNA
8.1-12
JC96-03616A
ELA UNIT-TONER TANK K;CLP-300,SEC,EXPORT
SNA
8.1-13
JC97-02332A
MEA-UNIT CASSETTE;CLP-300,SEC,WORLD,-,-,
Z4405
SA
8.1-14
JC97-02439A
MEA UNIT-COVER TOP;CLP-300,SEC,WORLD,-,Z4406
SA
8.1-15
JC97-02440A
MEA UNIT-COVER REAR;CLP-300,SEC,WORLD,-,
Z4407
SA
8.1-16
JC97-02659A
MEA-UNIT COVER FRONT;CLP-300,SEC,WORLD,Z4408
SA
8.1-18
JC63-00863A
SHIELD-P-MAIN LOWER;CLP-300,SECC,T1.0,99
SNA
8.1-19
JC44-00090A
SMPS-PSP_TYPE3_V2C;SCX-4521F,*,AC/DC,-,2
D2114
SA
8.1-20
JC44-00089A
HVPS-GOGH;-,24V,21.6V~26.4V,-,-,-,Z4410
SA
8.1-21
JC59-00018E
UNIT-LSU;CLP-300,-,-,STANDARD SINGLEBEAM
Z4411
SA
8.1-22
JC97-02656A
MEA UNIT-COVER LSU;CLP-300,SEC,EXPORT,-,
Z4412
SA
8.1-23
JC96-03609A
ELA UNIT-FUSER 220V;CLP-300,SEC,WORLD,-,
Z4413
SA
8.1-29
JC97-01771A
MEA UNIT-TERMINAL S;CLP-500,SEC,EXPORT,S
K3635
SA
8.1-30
3903-000042
CBF-POWER CORD;DT,EU,FP3/YES,IEC320 C13/
C0022
SA
8.2-1
JC61-01460A
GUIDE-M-STACKER COVER;CLP-300,ABS FR V0,
SNA
8.2-2
JC63-00846A
COVER-M-TOP;CLP-300,ABS FR,T2.5,279.3,37
SNA
8.2-3
JC63-00843A
COVER-M-JAM COVER;CLP-300,ABS FR,-,79.4,
SNA
8.2-4
JC64-00211A
KEY-M-OP1;CLP-300,ABS,-,-,36024,-,HF-066
Z4414
SA
8.2-5
JC63-00860A
COVER-M-LED;CLP-300,ABS,T1.5,52,77.9,-,SNA
8.2-6
6107-001169
SPRING-CS;SUS304-WPB,-,PI0.55,D9.3,14.25
Z4415
SA
8.2-6
6107-001306
SPRING-CS;SUS304-WPB,-,PI0.55,D6.45,L11,
SA
8.2-6
6107-001285
SPRING-CS;SUS304-WPB,-,PI0.45,D8.85,L12,
SNA
8.2-6
6107-001278
SPRING-CS;SUS304 WPB,-,PI0.7,D6.9,L20,-,
Z4416
SA
8.2-6
6107-001292
SPRING-CS;SUS304-WPB,-,PI0.55,-,L11.1,-,
SNA
8.2-7
JC72-01343A
PMO-SUB_M_STACKER;ML-1520,PC,BLACK,39*25
Z4139
SA
8.2-8
JC61-01761A
HOLDER-LEVER BLOCKING;CLP-300,PC,2.5,30.
SNA
8.2-9
JC66-01297A
LEVER-MID BLOCKING;CLP-300,PC+GF20,2.5,1
SNA
8.2-10
JC66-01296A
LEVER-BLOCKING;CLP-300,PC,2.5,39.6,30.2,
SNA
8.2-11
6044-000001
RING-CS;ID3,OD3,T0.25,BLACK,SUS304
SNA
8.2-11
6044-001005
RING-CS;ID4.8,OD10.0,T0.25,PASS,SUS-30
Z4417
SA
8.2-12
6002-000440
SCREW-TAPPING;PWH,+,-,2,M3,L8,ZPC(BLK),S
Z4418
SA
8.3-1
JC63-00844A
COVER-M-REAR;CLP-300,ABS,T3.0,249.3,296.
SNA
8.3-2
JC64-00215A
BUTTON-M-OPEN REAR;CLP-300,ABS FR V0,80.
SNA
8.3-3
JC66-01089A
SHAFT-P-LOCKBAR REAR;CLP-300,SECC,284,6,
SNA
8.3-4
JC61-01461A
HOLDER-M-HOOK REAR R;CLP-300,POM,T5.0,19
SNA
8.3-5
JC61-01456A
HOLDER-M-HOOK REAR L;CLP-300,POM,T5.0,19
SNA
8.3-6
JC61-01462A
HOLDER-M-HOOK REAR C;CLP-300,POM,T5.0,19
SNA
8.3-7
JC66-01071A
LEVER-M-REAR LOCK;CLP-300,HIPS,T2.5,55.1
SNA
8.3-8
6107-001268
SPRING-TS;SUS304 WPB,-,PI0.9,D8.9,L7,-,Z4419
SA
8.3-8
6107-001283
SPRING-TS;SWRS82A,-,1.0X0.6,D13.70,L12.1
Z4420
SA
8.3-8
6107-001284
SPRING-TS;SWRS82A,-,0.75X0.5,-,L8.4,-,-,
SNA
8.3-10
JC96-03990A
ELA UNIT-TRANSFER;CLP-300,SEC,EXPORT,-,Z4421
SA
8.4-1
JC63-00841A
COVER-M-FRONT;CLP-300,ABS FR,T2.5,185.3,
SNA
8.4-2
JC68-01678A
LABEL-INSTRUCTION;CLP-300,-,YUPO 150G,15
SNA
SA : SERVICE AVAILABLE SNA : SERVICE not AVAILABLE DNA : DELIVERY not AVAILABLE
Drawer#
SEC-Code
Description & Specification
Location Service
8.5-1
JC61-01450A
BRACKET-P-DRIVE MOTOR;CLP-300,SECC,T1.2,
SNA
8.5-2
6031-001528
WASHER-PLAIN;POLYMIDE,-,ID6,OD13.5,T0.5,
Z4422
SA
8.5-2
6031-001051
WASHER-PLAIN;M4,ID4.1,OD7.0,T0.13,*,POLY
SNA
8.5-2
6031-001543
WASHER-PLAIN;POLY,-,ID5.1,OD8,T0.13,-,SNA
8.5-2
6031-001547
WASHER-PLAIN;POLY,-,ID6.5,OD12,T0.5,-,SNA
8.5-2
6031-001577
WASHER-PLAIN;POLY,-,ID5.1,OD14,T0.5,BLK,
SNA
8.5-3
JC66-01042A
GEAR-IDLE DEVE Z19;CLP-300,POM,M0.8,Z19,
Z4423
SA
8.5-4
JC66-01052A
GEAR-RDCN DEVE CAM;CLP-300,POM,M0.8/M0.6
Z4424
SA
8.5-5
JC66-01041A
GEAR-DEVE COUPLING;CLP-300,POM,M0.8,Z18,
Z4425
SA
8.5-6
6107-001271
SPRING-CS;SUS304 WPB,-,PI0.55,D6.75,L9.0
Z4426
SA
8.5-7
JC66-01047A
GEAR-IDLE Z39;CLP-300,POM,M0.8,Z39,-,WHI
Z4427
SA
8.5-8
JC66-01065A
GEAR-TONER DRIVE;CLP-300,POM,M0.8/Z0.8,Z
Z4428
SA
8.5-9
JC66-01046A
GEAR-IDLE Z33;CLP-300,POM,M0.8,Z33,-,WHI
Z4429
SA
8.5-10
JC66-00763A
GEAR-M-PICK UP IDLE;CLP-600,POM,M0.8,SPU
G0031
SA
8.5-11
JC47-00007E
MEP-CLUTCH CAM;-,CLP-300,-,DC24V,0.133A,
Z4430
SA
8.5-12
JC66-01208A
GEAR-RDCN FUSER CAM;CLP-300,POM,M0.8/Z0.
Z4431
SA
8.5-13
JC66-01045A
GEAR-IDLE ITB Z43;CLP-300,POM,M0.5,Z43,Z4432
SA
8.5-14
JC66-01048A
GEAR-ITB DRIVE;CLP-300,POM,M0.5/M0.5,Z10
Z4433
SA
8.5-15
JC66-01054A
GEAR-RDCN OPC;CLP-300,POM,M0.5/M0.6,Z79/
Z4434
SA
8.5-16
JC63-01049A
SHEET-HOUSING ITB;CLP-300,PET FILM,T0.18
SNA
8.5-17
JC66-01051A
GEAR-RDCN DEVE;CLP-300,POM,M0.5/M0.8,Z73
Z4435
SA
8.5-18
JC66-01055A
GEAR-RDCN P_PATH;CLP-300,POM,M0.5/M0.8,Z
Z4436
SA
8.5-19
JC66-01050A
GEAR-PICK UP DRIVE;CLP-300,POM,M0.8/M0.8
Z4437
SA
8.5-20
JC66-01044A
GEAR-FUSER DRIVE 1;CLP-300,POM,M0.8,Z45,
Z4438
SA
8.5-21
JC66-01053A
GEAR-RDCN EXIT;CLP-300,POM,M0.8/M0.8,Z51
Z4439
SA
8.5-22
JC66-01043A
GEAR-DEVE DRIVE;CLP-300,POM,M0.6,Z21,-,W
Z4440
SA
8.5-23
6031-001255
WASHER-PLAIN;NYLON,CUTTING,ID5,OD9,T0.5,
W0004
SA
8.5-24
JC66-00771A
GEAR-_M_IDLE PICKUP;CLP-600,POM,M0.8,SPU
G0010
SA
8.5-25
JC61-01459A
BRACKET-M-DRIVE FRONT;CLP-300,PC,T2.5,W1
SNA
8.5-26
JC66-01061A
SHAFT-IDLE D8;CLP-300,SUM24L+NI,L16.7,D1
SNA
8.5-27
JC66-01064A
GEAR-IDLE Z37;CLP-300,POM,M0.8,Z37,-,WHI
Z4441
SA
8.5-28
6003-000301
SCREW-TAPTITE;BH,+,S,M4,L6,ZPC(YEL),SWRC
SNA
8.5-28
6003-000152
SCREW-TAPTITE;PH,+,B,M2,L10,ZPC(YEL),SWR
Z4442
SA
8.5-28
6002-000308
SCREW-TAPTITE;PH,+,B,M2.6,L6,ZPC(YEL),SW
Z4443
SA
8.5-29
JC66-01060A
SHAFT-WORM GEAR;CLP-300,SUM24L+NI,L44.6,
SNA
8.5-30
JC66-01057A
GEAR-WORM DEVE CAM;CLP-300,POM,M0.6/M0.6
Z4444
SA
8.5-31
6044-000159
RING-C;ID3,OD7,T0.6,PASS,STSC
Z4357
SA
8.5-32
6001-000130
SCREW-MACHINE;BH,+,M3,L6,ZPC(WHT),SWRCH1
Z4445
SA
8.5-32
6001-000485
SCREW-MACHINE;PH,+,M2.6,L4,ZPC(YEL),SWRC
SNA
8.5-33
JC66-01070A
LATCH-M-HUB CLUTCH;CLP-300,POM,T2.0,D18.
SNA
8.5-34
JC66-01155A
GEAR-FUSER RDCN OUT V;ML-3560,HTNFR52G30
SNA
8.5-35
6044-000231
RING-E;ID5.0,OD11.0,T0.6,PASS,STS304
R0006
SA
8.5-36
JC66-01068A
SHAFT-M-T2 CAM;CLP-300,POM,L52,D20,BLACK
Z4446
SA
8.5-37
JC66-01067A
SHAFT-M-ITB CLEAN CAM;CLP-300,POM,L44,D2
Z4447
SA
8.5-38
JC31-00041A
MOTOR DC-DEVE DRIVE;50M843A152,CLP-600,2
M0024
SA
8.5-39
JC33-00015C
SOLENOID-PICK UP;-,CLP-300,DC24V,48§Ù¡¾1 S
Z4448
SA
8.5-40
6003-000269
SCREW-TAPTITE;BH,+,-,S,M3,L6,ZPC(YEL),SW
Z4449
SA
8.5-41
JC61-01458A
BRACKET-M-DEVE CAM;CLP-300,PC+ABS,T2.5,W
SNA
8.5-42
6003-000196
SCREW-TAPTITE;PWH,+,B,M3,L10,NI PLT,SWRC
Z4397
SA
8.5-43
JC67-00130A
CAP-M-PUSH COUPLING;CLP-300,POM,T2.0,D13
Z4450
SA
8.5-44
JC97-01788B
MEA UNIT-CLUTCH DEV;CLP-300,-,WORLD,M0.6
Z4451
SA
8.5-45
JC66-01066A
SHAFT-M-DEVE CAM;CLP-300,POM,L116,D18.3,
Z4452
SA
8.5-46
JC92-01720A
PBA SUB-DEVE_HOME;CLP-300,SEC,KOREA,DEVE
Z4453
SA
8.5-47
JC61-01453A
HOLDER-M-LINK BLACK;CLP-300,PC+ABS,T2.5,
Z4454
SA
8.5-48
JC66-01097A
LINK-M-PUSH BLACK CAP;CLP-300,POM,22,T2.
Z4455
SA
8.5-49
JC61-00699A
BUSH-D6/L4;CLP-500,BRONZE+ST,ID6.0,OD9.0
B0027
SA
8.5-50
6502-001093
CABLE CLAMP;DAWS-3NE,ID11*L34.8,-,NYLON6
C0002
SA
SA : SERVICE AVAILABLE SNA : SERVICE not AVAILABLE DNA : DELIVERY not AVAILABLE
Drawer#
SEC-Code
Description & Specification
Location Service
8.5-50
6502-000121
CABLE CLAMP;DAMC-101,D7~8,L19,SCP-1,NTR
SNA
8.5-51
0205-001003
GREASE-BEARING;NYOGEL788,DAMPING GREASE,
SNA
8.5-51
0205-001059
GREASE-BEARING;PETAMO GHV 133,BEIGE,15KG
SNA
8.5-51
0205-001144
GREASE-BEARING;SF-112,HANARL,NOISE TAMPI
SNA
8.5-51
0205-001080
GREASE-BEARING;NYOGEL 774H,NOISE DAMPING
SNA
8.5-51
0205-001095
GREASE-BEARING;NYE8512,NOISE DAMPING(BLU
SNA
8.5-52
JF68-10532B
LABEL(P)-BAR CODE;CLP-500,-,YUPO PAPER,1
SNA
8.6-27
JC66-01133A
LEVER-M-ACTUATOR FEED;CLP-300,POM,T2.5,3
SNA
8.6-65
6044-000125
RING-E;ID4,OD9,T0.6,PASS,STSC
R0004
SA
8.6-11
6107-001282
SPRING-CS;C5210W,-,PI0.6,-,L12.5,-,-,ID3
Z4456
SA
8.6-34
JC39-00302A
CBF HARNESS-100M_GND;CLP-500,-,-,1 PIN,5
C0007
SA
8.6-34
JC61-01486A
PLATE-P-GROUND PICKUP;CLP-300,C5210P,T0.
SNA
8.6-35
JC63-00854A
COVER-M-GROUND OPC;CLP-300,ABS HB,T1.5,
SNA
8.6-35
JC39-00493A
CBF HARNESS-THER;CLP-300,WIRE HARNESS,UL
Z4457
SA
8.6-54
JC39-00497A
CBF HARNESS-INLET;CLP-300,WIRE HARNESS,U
Z4458
SA
8.6-37
6107-001163
SPRING-CS;SUS304-WPB,-,PI0.4,D3.9,L13,-,
Z4460
SA
8.6-37
JC39-00498A
CBF HARNESS-COVER S/W;CLP-300,WIRE HARNE
Z4459
SA
8.6-38
JC39-00578A
CBF HARNESS-GND_BRK;CLP-300,WIRE HARNESS
Z4461
SA
8.6-38
JC61-00829B
HOLDER-BEARING EXIT F/DOWN;CLP-300,POM(A
Z4462
SA
8.6-39
JC66-01149A
ROLLER-EXIT MAIN;CLP-300,PFA,D8.5,L23,BL
Z4464
SA
8.6-39
JC39-00579A
CBF HARNESS-LSU_S/W;CLP-300,WIRE HARNESS
Z4463
SA
8.6-47
JC39-00581A
CBF HARNESS-FUSER_AC;CLP-300,WIRE HARNES
Z4465
SA
8.6-41
JC39-00583A
HARNESS-GND_FRAME;CLP-300,WIRE HARNESS,U
Z4466
SA
8.6-41
JC66-01040A
ROLLER-EXIT F DOWN;CLP-300,SUM22/EPDM,D4
SNA
8.6-55
JC61-01546A
SPRING ETC-OPC LOCK L;CLP-300,C5210W,D1.
Z4468
SA
8.6-55
JC47-00009C
MEP-CLUTCH REGI;-,CLP-300,3.0W,DC24V,125
Z4467
SA
8.6-58
JC47-00014A
MEP-CLUTCH CAM;-,CLP-300,-,DC24V,0.18A,C
Z4469
SA
8.6-58
JC61-01566A
HOLDER-M-CLUTCH FUSER;CLP-300,PC+ABS,T2.
SNA
8.6-1
JC61-01443A
FRAME-M BASE GOGH;CLP-300,PC+ABS,NH-1000
SNA
8.6-33
JC61-01451A
PLATE-P-GROUND OPC L;CLP-300,C5210P,T0.2
SNA
8.6-59
JC61-01478A
GUIDE-M-HARNESS;CLP-300,ABS,HB,T2.5,118.
SNA
8.6-18
JC61-01482A
PLATE-P-GROUND FUSER;CLP-300,SUS304-CSP,
SNA
8.6-13
JC61-01483A
PLATE-P-GROUND LSU;CLP-300,C5210P,T0.2,1
SNA
8.6-16
JC61-01484A
PLATE-P-GROUND T2;CLP-300,C5210P,T0.2,21
SNA
8.6-14
JC61-01485A
PLATE-P-GROUND REGI;CLP-300,SUS304 CSP,T
SNA
8.6-19
JC61-01489A
PLATE-P-GROUND EXIT;CLP-300,SUS 304 CSP,
SNA
8.6-17
JC61-01537A
PLATE-P-SHAFT LACK;CLP-300,SECC,T1.0,4,1
SNA
8.6-15
JC61-01547A
SPRING ETC-OPC LOCK R;CLP-300,C5210W,D1.
Z4470
SA
8.6-57
JC61-01548A
HOLDER-M-CAM;CLP-300,POM (DE8903),T2.0,1
SNA
8.6-2
JC61-40001A
FOOT-ML80;ML-80,NBR,-,GRAY,-,-,F0003
SA
8.6-60
JC61-70940A
SPRING ETC-TR(12);ML-5500,-,4.5,-,12.7,1
O1054
SA
8.6-3
JC66-00050A
CAM-CATCH;ML-9400W,POM,-,34¡¿18¡¿7,WHITE S
C0004
SA
8.6-12
JC66-00346A
GEAR-MP/DUP DRV;SCX-5100,POM,SW-01,M0.8,
G0340
SA
8.6-10
JC66-01056A
GEAR-REGI DRIVE;CLP-300,POM,M0.8,Z32,-,W
Z4471
SA
8.6-62
JC66-01120A
SHAFT-FEED IDLE;CLP-300,SUM22+NI,L237,D8
SNA
8.6-64
JC66-01128A
ROLLER-REGI;CLP-300,SUM22+EPDM,D6.0/D14.
SNA
8.6-67
JC66-01207A
SHAFT-M-CLUTCH FUSER;CLP-300,POM,L39.8,D
Z4472
SA
8.6-68
JC70-00050A
IPR-TERMINAL;SF-5100,SWRCH1018,-,-,-,-,8
SNA
8.6-61
JC72-00102A
PMO-BUSHING_TR(L);SF-5100,POM (CH-15),BL
O1101
SA
8.6-20
JC92-01714A
PBA SUB-PANEL;CLP-300,SEC,KOREA,PANEL,-,
Z4473
SA
8.6-32
JC92-01723A
PBA SUB-WASTE_T;CLP-300,SEC,KOREA,WASTE_
Z4474
SA
8.6-72
JC92-01718A
PBA SUB-EXIT;CLP-300,SEC,KOREA,EXIT SENS
Z4475
SA
8.6-49
6006-000127
SCREW-MACHINE;WS,PH,+,M3,L6,ZPC(YEL),SWR
SNA
8.6-75
6021-000222
NUT-HEXAGON;2C,M3,ZPC(YEL),SM20C,SNA
8.6-46
JC70-10961A
IPR-TERMINAL FU;ML-165,C5210P,-,T0.3,-,K3422
SA
8.6-45
JC72-41010A
PMO-HOUSING TERMINAL;ML-165,ABS GF10%,BL
H6086
SA
8.6-78
JC97-02362A
MEA UNIT-DRAW;CLP-300,SEC,WORLD,-,-,-,Z4476
SA
SA : SERVICE AVAILABLE SNA : SERVICE not AVAILABLE DNA : DELIVERY not AVAILABLE
Drawer#
SEC-Code
Description & Specification
Location Service
8.6-79
6009-001396
SCREW-SPECIAL;PH,+,-,M3,L10.3,ZPC(BLK),S
SNA
8.6-5
JC39-00488A
CBF HARNESS-MAIN_DRAW;CLP-300,WIRE HARNE
Z4477
SA
8.6-4
JC61-01521A
PLATE-P-DRAW CONNECTOR;CLP-300,SECC,T1.0
SNA
8.6-26
JC61-00018A
SPRING ETC-SENSOR;SF-5100,SUS304WPB,0.2,
SNA
8.6-28
JC61-01480A
HOLDER-M-ACTUATOR FEED;CLP-300,ABS,T2.5,
SNA
8.6-87
JC72-00463A
PMO-CAP CONNECTOR L;ML-6060A,POM,BLACK,Z0013
SA
8.6-88
JC72-00465A
PMO-CAP CONNECTOR U;ML-6060A,POM,BLACK,Z0014
SA
8.6-36
JC61-01477A
FRAME-M-EXIT;CLP-300,PC,NH-1035,5V,BLACK
SNA
8.6-42
JC61-01568A
HOLDER-M-EXIT F DOWN;CLP-300,PC,T2.5,26.
SNA
8.6-44
JC66-00810A
GEAR-EXIT_DRV17;ML-1610,POM,0.8,17,-,BLK
O1073
SA
8.6-100
6107-001167
SPRING-CS;SUS304-WPB,-,PI0.25,D3.25,L9.6
Z4318
SA
8.6-101
JC61-01151A
HOUSING-M-PICK_U;ML-1610,POM,-,-,35,NATU
P2067
SA
8.6-102
JC61-01173A
HOUSING-M-PICK_UP B;ML-1610,ABS HB,-,-,3
P2068
SA
8.6-103
JC61-01473A
GUIDE-M-PICK UP;CLP-300,PC+ABS,HB,T2.5,5
SNA
8.6-104
JC61-01533A
PLATE-P-PICK UP;CLP-300,SECC,T1.0,264,43
SNA
8.6-105
JC61-01538A
HOLDER-M-PAD;CLP-300,PC+ABS,HB,T2.5,-,-,
SNA
8.6-106
JC61-01570A
GUIDE-M-PAPER;CLP-300,POM M90-44,T2.0,15
SNA
8.6-107
JC61-70911A
SPRING ETC-EXIT ROLL FD;ML-165,SUS304 WP
O1053
SA
8.6-108
JC66-00815A
LEVER-M-KICKER P/U;ML-1610,POM,-,10.5,31
R1120
SNA
8.6-109
JC66-01076A
GEAR-PICK UP A;CLP-300,POM,M0.8,Z45,-,WH
Z4478
SA
8.6-110
JC66-01077A
GEAR-PICK UP B;CLP-300,POM,M0.8,Z45,-,WH
Z4479
SA
8.6-111
JC66-01080A
SHAFT-P-PICKUP;CLP-300,SECC,L286,T1.2,-,
SNA
8.6-112
JC66-01105A
CAM-M-PICK UP;CLP-300,POM M90-44,-,-,WHI
SNA
8.6-113
JC69-00961A
PAD-FRICTION;CLP-300,NBB,T1.0,W9.0,L39.5
Z4480
SA
8.6-114
JC73-00211A
RUBBER-PICK_UP;ML-1610,EPDM+IR,MM,-,-,-,
P2148
SA
8.6-23
JB61-00076A
SPRING ETC-TORSION DOC (CC2-F);SCX-1110F
O1013
SA
8.6-25
JC61-01481A
HOLDER-M-ACTUATOR EMPTY;CLP-300,ABS,T2.5
SNA
8.6-24
JC66-01119A
LEVER-M-ACTUATOR EMPTY;CLP-300,PC,T2.5,5
SNA
8.7-1
JC67-00168A
BRUSH-LSU;CLP-300,PP BRUSH,-,W4.5,L180.6
SNA
8.7-2
JC64-00267A
SHUTTER-LSU;CLP-300,ABS GF20,T2.5,W11.5,
SNA
8.7-3
JC63-00839A
COVER-M-LSU;CLP-300,ABS HB,T2.0,239.5,1
SNA
8.7-4
6107-001295
SPRING-CS;SUS304,-,PI0.45,D5.45,L22.5,-,
SNA
8.7-5
JC63-01093A
SHEET-LSU FRONT;CLP-300,PET SHEET,T0.188
SNA
8.7-6
JC62-00338A
SEAL-COVER LSU;CLP-300,EPDM,-,T2.5,W8,L1
SNA
8.8-1
JC61-01474A
FRAME-M-UPPER FUSER;CLP-300,PET+GF30%,BN
SNA
8.8-2
JC61-01475A
FRAME-M-LOWER FUSER;CLP-300,PET+GF30%,BN
SNA
8.8-3
JC66-01078A
ROLLER-HEAT;CLP-300,AL5052+RUBBER,D27.5,
SNA
8.8-4
JC66-00669A
GEAR-FUSER;SCX-5315F,PPS, OFL4036,1,34,P
Z4481
SA
8.8-5
JC66-10902A
BEARING-H/R L;ML-165,PPS(RBA313N),-,ID26
B1019
SA
8.8-6
JC72-00814A
PMO-BEARING H/R-F;SCX-5100,-,PPS,BLK,V0,
B1040
SA
8.8-7
4712-001027
THERMOSTAT;125/250VAC,15/7.5A,170+-5C,0C
T0002
SA
8.8-8
JC66-01079A
ROLLER-PRESSURE;CLP-300,SUM22,D16,L237.5
SNA
8.8-9
JC66-01111A
ROLLER-PRESSURE SHAFT;CLP-300,SUM22,D8.0
SNA
8.8-10
JC61-01490A
HOLDER-M-BUSH 2PR_R;CLP-300,PBT,T2.0,33.
SNA
8.8-11
JC61-01491A
HOLDER-M-BUSH 2PR_L;CLP-300,PBT,T2.0,33.
SNA
8.8-12
JC61-01534A
BUSH-M-2PR L;CLP-300,PPS(RBA313N),-,-,5.
SNA
8.8-13
JC61-01535A
BUSH-M-2PR R;CLP-300,PPS(RBA313N),-,5.3,
SNA
8.8-14
JC61-01522A
GUIDE-M-INPUT FUSER;CLP-300,PET+GF30%,5V
SNA
8.8-15
JC66-01110A
LEVER-M-ACTUATOR EXIT;CLP-300,PET+GF30%,
SNA
8.8-16
JC61-01476A
PLATE-P-GROUND FUSER;CLP-300,SUS 304 CSP
SNA
8.8-17
JC70-00518A
ELECTRODE-P-AC R;CLP-300,C5210P T0.8,D3.
SNA
8.8-18
JC70-00519A
ELECTRODE-P-AC L;CLP-300,C5210P T0.8,D3.
SNA
8.8-19
JC68-00407A
LABEL(R)-HV FUSER;ML-6060,PVC,-,220V,-,,
L0006
SNA
8.8-20
JC68-01134A
LABEL(P)-BLANK(FUSER);ML-1710D3,-,WHITE
SNA
8.8-21
JC68-01581A
LABEL(P)-CAUTION HOT;COMMON,SAMSUNG,PET,
SNA
8.8-22
6107-001246
SPRING-CS;SWP-B,-,PI0.9,D5.6,L16.6,-,-,I
SNA
8.8-23
6107-001267
SPRING-CS;SWP-B,-,PI1.0,D5.9,L17,-,-,ID4
Z4482
SA
SA : SERVICE AVAILABLE SNA : SERVICE not AVAILABLE DNA : DELIVERY not AVAILABLE
Drawer#
SEC-Code
Description & Specification
Location Service
8.8-24
JC39-00500A
CBF HARNESS-FUSE_LINK1;CLP-300,WIRE HARN
Z4483
SA
8.8-25
JC39-00501A
CBF HARNESS-FUSE_LINK2;CLP-300,WIRE HARN
Z4484
SA
8.8-27
6003-000261
SCREW-TAPTITE;BH,+,B,M3,L6,ZPC(YEL),SWRC
SNA
8.8-28
4713-001210
LAMP-HALOGEN;230V,-,850W,-,-,-,8x299.5mm
Z4485
SA
8.8-29
1404-001368
THERMISTOR-NTC ASSY;1KOHM,-,4537K,0.25MW
Z4486
SA
8.8-30
JC70-00064A
IPR-PIN ROLLER EXIT;SF-5100,SUS304,PI1.8
SNA
8.8-31
JC72-20902A
PEX-ROLLER F/UP(2);ML-5000A,TEFLON,WHT,O1106
SA
8.8-32
JC72-00382A
PMO-BUSHING TX;ML-6060A,POM M9044,BLK,-,
SNA
8.8-33
JC66-01206A
SHAFT-M-CAM FUSER;CLP-300,PC+GF30%,L252.
SNA
8.8-34
JC61-01647A
HOLDER-M-SHAFT FUSER;CLP-300,PC,T2.0,-,L
SNA
8.8-35
JC66-01147A
LEVER-M-RELEASE;CLP-300,PET+GF30%,T1.5,W
SNA
8.8-36
JC66-01148A
LEVER-M-LINK FUSER;CLP-300,PET+GF30%,T1.
Z4487
SA
8.8-37
JC61-01523A
GUIDE-M-OUTPUT FUSER;CLP-300,PET+GF30%,5
SNA
8.8-38
JC61-01271A
SPRING ETC-ACTUATOR;CLP-600,SUS304 ,0.35
S0018
SA
8.8-39
JC97-02778A
MEA UNIT-GUIDE PR;CLP-300,SEC,EXPORT,-,SNA
8.8-40
6107-001290
SPRING-CS;SUS304 WPB,-,PI0.55,D5.55,L16,
Z4488
SA
8.8-41
JC66-01309A
ROLLER-DUMMY;CLP-300,PFA,OD6.0,L10.0,-,SNA
8.8-42
JC61-01685A
SPRING ETC-DUMMY;CLP-600,SUS,0.5,-,-,20.
Z4489
SA
8.8-43
JC61-01679A
SPRING ETC-GROUND;CLP-300,SUS 304 WPB,¥Õ
Z4490
SA
8.9-2
6006-001078
SCREW-TAPTITE;WSP,PH,+,M3,L10,ZPC(YEL),S
SNA
8.9-4
JC39-00499A
CBF HARNESS-JOIN_DRAW;CLP-300,WIRE HARNE
SNA
8.9-5
JC63-01142A
SHEET-FILM YELLOW UP;CLP-300,PC,T0.38,W5
SNA
8.9-6
JC67-00199A
CAP-DEVE;CLP-300,PP,-,31.5,62,-,SNA
8.9-7
JC68-01708A
LABEL-INFORMATION;CLP-300,-,WHITE POLY,T
SNA
8.9-7
JC68-01766A
LABEL-INFORMATION;CLP-300,DSL,YUPO,0.08,
SNA
8.9-8
JC68-10914D
LABEL(P)-SERIAL NO;ML-85,ART,70X15,G100,
SNA
8.9-9
JC69-01013A
CUSHION-DEVE;CLP-300,EPP,T10,W75,L351,-,
SNA
8.9-10
JC96-03911A
ELA UNIT-DEV MAIN SET;CLP-300,SEC,EXPORT
SNA
8.9-11
JC97-02571A
MEA UNIT-OPC SET;CLP-300,SEC,WORLD,-,-,SNA
8.9-12
JC97-02613A
MEA UNIT-DEV Y;CLP-300,SEC,EXPORT,-,-,-,
SNA
8.9-13
JC97-02614A
MEA UNIT-DEV M;CLP-300,SEC,EXPORT,-,-,-,
SNA
8.9-14
JC97-02615A
MEA UNIT-DEV C;CLP-300,SEC,EXPORT,-,-,-,
SNA
8.9-15
JC97-02616A
MEA UNIT-DEV K;CLP-300,SEC,EXPORT,-,-,-,
SNA
8.9-16
JC97-02619A
MEA UNIT-TONER WASTE;CLP-300,SEC,EXPORT,
SNA
8.10-4
0604-001257
PHOTO-INTERRUPTER;TR,-,-,DIP-4,BK
SNA
8.10-4
0604-001154
PHOTO-INTERRUPTER;TR,0.2-1.0MA,80MW,DIP,
P0012
SA
8.10-5
6003-000282
SCREW-TAPTITE;BH,+,-,B,M3,L8,ZPC(BLK),SW
Z4491
SA
8.10-6
6031-000019
WASHER-PLAIN;-,ID6.1,OD8.5,T0.1,BLK,POLY
SNA
8.10-7
6107-001287
SPRING-CS;SUS304-WPB,-,PI0.6,D6.5,L25,-,
SNA
8.10-8
6107-001288
SPRING-CS;SUS304-WPB,-,PI0.35,D3.55,L12,
SNA
8.10-9
6107-001289
SPRING-CS;SUS304-WPB,-,PI0.95,-,L21.2,-,
SNA
8.10-10
JC02-00054A
TONER-BLACK;CLP-300,SAK-79JG-K1,BLACK,8.
SNA
8.10-11
JC39-00489A
CBF HARNESS-ITB_JOINT;CLP-300,WIRE HARNE
SNA
8.10-12
JC39-00502A
CBF HARNESS-ITB_HOME;CLP-300,WIRE HARNES
SNA
8.10-14
JC61-01494A
FRAME-M-ITB;CLP-300,ABS+GF20%,GR-4020,-,
SNA
8.10-15
JC61-01495A
FRAME-M-WASTE ITB;CLP-300,ABS GF20%,GR-4
SNA
8.10-16
JC61-01497A
HOUSING-M-CLEANING ITB;CLP-300,ABS GF 20
SNA
8.10-17
JC61-01498A
HOLDER-M-BUSH CHARGE;CLP-300,POM(M90-44)
SNA
8.10-18
JC61-01499A
GUIDE-M-POLE ITB;CLP-300,ABS HF-0660I,-,
SNA
8.10-19
JC61-01502A
BRACKET-P-HOUSING LEFT;CLP-300,SECC,1.2T
SNA
8.10-20
JC61-01503A
BRACKET-P-HOUSING RIGHT;CLP-300,SECC,1.2
SNA
8.10-21
JC61-01504A
PLATE-P-GND ITB;CLP-300,BRONZE(C5210P-H)
SNA
8.10-22
JC61-01505A
HOLDER-M-PTL;CLP-300,ABS HB HF-0660I,10.
SNA
8.10-23
JC61-01506A
HOLDER-M-HOME SENSOR;CLP-300,ABS HB(HF-0
SNA
8.10-24
JC61-01536A
BUSH-M-CHARGE CLEANING;CLP-300,POM(M90-4
SNA
8.10-25
JC61-01539A
BUSH-M-DRIVE ITB;CLP-300,POM(M90-44),ID6
SNA
8.10-26
JC61-01540A
BUSH-M-ITB;CLP-300,POM(M90-44),ID6,OD8.1
SNA
SA : SERVICE AVAILABLE SNA : SERVICE not AVAILABLE DNA : DELIVERY not AVAILABLE
Drawer#
SEC-Code
Description & Specification
Location Service
8.10-27
JC61-01541A
BUSH-M-TR ITB;CLP-300,POM(AT-15CF),ID6,SNA
8.10-28
JC61-01542A
BUSH-M-IDLER WASTE BELT;CLP-300,POM(M90SNA
8.10-29
JC61-01543A
BUSH-CHARGE LEFT;CLP-300,SINTERED BRONZE
SNA
8.10-30
JC61-01701A
SPRING ETC-SHUTTER;CLP-300,SWP-B,¡Ë0.35,S
SNA
8.10-31
JC61-01704A
SPRING ETC-GROUND ITB;CLP-300,SUS304-WPB
SNA
8.10-32
JC62-00210A
SEAL-AUGER OPC;CLP-300,PORON LE-20,-,5T,
SNA
8.10-33
JC62-00212A
SEAL-BELT ITB;CLP-300,URETHANE FILM,-,0.
SNA
8.10-34
JC62-00213A
SEAL-LOW ITB;CLP-300,POLYURETHANE,-,6T,W
SNA
8.10-35
JC62-00217A
SEAL-COVER WASTE;CLP-300,PORON,-,T2,W11.
SNA
8.10-36
JC62-00219A
SEAL-BACK ITB;CLP-300,POLYURETHANE FOAM,
SNA
8.10-37
JC62-00221A
SEAL-BACK ITB RIGHT;CLP-300,POLYURETHANE
SNA
8.10-38
JC62-00222A
SEAL-SIDE ITB LEFT;CLP-300,POLYURETHANE
SNA
8.10-39
JC62-00223A
SEAL-SIDE ITB RIGHT;CLP-300,POLYURETHANE
SNA
8.10-40
JC62-00229A
SEAL-BLADE ITB LEFT;CLP-300,POLYURETHANE
SNA
8.10-41
JC62-00232A
SEAL-TOP ITB;CLP-300,POLYURETHANE,-,10T,
SNA
8.10-42
JC62-00257A
SEAL-FRAME WASTE ITB;CLP-300,PORON LE-20
SNA
8.10-43
JC62-00258A
SEAL-WASTE OPC;CLP-300,PORON LE-20,-,T0.
SNA
8.10-44
JC62-00281A
SEAL-HOUSING ITB L;CLP-300,PORON LE-20,B
SNA
8.10-45
JC62-00282A
SEAL-HOUSING ITB R;CLP-300,PORON LE-20,B
SNA
8.10-46
JC62-00326A
SEAL-WASTE SIDE;CLP-300,POLY URETHANE FO
SNA
8.10-47
JC63-00857A
COVER-M-WASTE ITB;CLP-300,PC,2.0T,W49.4,
SNA
8.10-48
JC63-00859A
COVER-M-WASTE EXIT;CLP-300,POM(M90-44),T
SNA
8.10-49
JC63-00862A
COVER-M-HANDLE ITB;CLP-300,ABS HF-0660I,
SNA
8.10-50
JC63-01045A
SHEET-FRAME ITB;CLP-300,PC,T0.125,W80.5,
SNA
8.10-52
JC63-01124A
SHEET-HOUSING ITB F;CLP-300,PET,T0.188,W
SNA
8.10-53
JC63-01170A
SHEET-BLADE ITB;CLP-300,PC,T0.5,5,222.5,
SNA
8.10-54
JC66-01082A
ARM-M-BLADE ITB;CLP-300,PC,T5.0,53,L71,B
SNA
8.10-55
JC66-01083A
SHAFT-M-BELT WASTE;CLP-300,POM(M90-44),L
SNA
8.10-56
JC66-01085A
SHAFT-M-AUGER ITB;CLP-300,ABS+GF20%,253,
SNA
8.10-57
JC66-01087A
GEAR-AUGER ITB;CLP-300,POM (M90-44),M0.8
SNA
8.10-58
JC66-01112A
DRUM-ITB BELT;CLP-300,PI,OD120,W240,L376
SNA
8.10-59
JC66-01131A
ROLLER-T1;CLP-300,NBR + ECO FORM,OD14,L2
SNA
8.10-60
JC67-00027A
LENS-PTL;ML-1710,PMMA,NTR,-,-,-,K3433
SA
8.10-62
JC72-40332A
PMO-BUSHING_CHARGE;ML-80,POM,BLK,HB,SNA
8.10-63
JC73-00222A
RUBBER-BELT WASTE ITB;CLP-300,CR+NR20%,1
SNA
8.10-64
JC92-01709A
PBA SUB-ITB_JOINT;CLP-300,SEC,KOREA,ITBSNA
8.10-71
JC92-01724A
PBA SUB-PTL;CLP-300,SEC,KOREA,PTL,-,-,-,
SNA
8.10-75
JC97-02645A
MEA UNIT-BLADE ITB;CLP-300,SEC,EXPORT,-,
SNA
8.10-81
JC97-02646A
MEA UNIT-ROLL DRV ITB;CLP-300,SEC,EXPORT
SNA
8.10-85
JC97-02695A
MEA UNIT-ROLL IDL ITB;CLP-300,SEC,WORLD,
SNA
8.11-1
JC61-01530A
FRAME-M-SEMI CASSETTE;CLP-300,ABS,HF-066
SNA
8.11-2
JG61-70531A
SPRING ETC-LOCKER,PLATE;SF6000,STS304WPB
S0025
SA
8.11-3
JC64-00222A
LOCKER-M-KNOCK UP R;CLP-300,POM (M90-44)
Z4492
SA
8.11-4
JC64-00223A
LOCKER-M-KNOCK UP L;CLP-300,POM (M90-44)
Z4493
SA
8.11-5
JC97-02218A
MEA UNIT-PLATE KNOCK_UP;ML-1610,SAMSUNG,
K3602
SA
8.11-6
6107-001240
SPRING-CS;SUS304-WPB,GROUND END,PI0.6,D1
D4084
SA
8.11-7
JC70-00516A
ADJUST-M-CASSETTE R;CLP-300,ABS HB,T2.5,
Z4494
SA
8.11-8
JC70-00517A
ADJUST-M-CASSETTE L;CLP-300,ABS HB,T2.5,
Z4495
SA
8.11-9
JG66-40003A
GEAR-PINION;SF4000,POM,WHT,M1,Z16
O1127
SA
8.11-13
JC63-00869A
TRAY-M-EXTENSION SMALL;CLP-300,ABS,T2.5,
SNA
8.11-14
JC63-00855A
COVER-M-CASSETTE;CLP-300,ABS,T2.5,77,224
SNA
8.11-16
JC68-01679A
LABEL-INSTRUCTION;CLP-300,-,WHITE PET,T0
SNA
8.11-17
JC68-01680A
LABEL-INSTRUCTION;CLP-300,-,WHITE PET,T0
SNA
#N/A
JC61-01531A
STOPPER-M-PAPER REAR;CLP-300,ABS HB,T2.5
SNA
#N/A
JC61-01572A
HOLDER-M-SHAFT CLUTCH;CLP-300,POM,T1.5,D
SA
#N/A
JC62-00227A
SEAL-SHUTTER BOTTLE;CLP-300,POLYURETHANE
SNA
#N/A
JC62-00237A
SEAL-AGITATOR BOTTLE;CLP-300,PORON,BLACK
SNA
SA : SERVICE AVAILABLE SNA : SERVICE not AVAILABLE DNA : DELIVERY not AVAILABLE
Drawer#
SEC-Code
Description & Specification
Location Service
#N/A
3704-000349
SOCKET-IC;8P,DIP,SN,2.54MM
SNA
#N/A
JC62-00259A
SEAL-BOTTLE AUGER;CLP-300,PORON LE-20,-,
SNA
#N/A
JC63-00864A
SHIELD-P-SMPS;CLP-300,SECC,T1.0,109.7,19
SNA
#N/A
JC63-00872A
TRAY-M-EXT CASSETTE;CLP-300,ABS,T2.5,118
SNA
#N/A
JC63-01110A
SHEET-BRACKET ITB;CLP-300,PET FILM,T0.18
SNA
#N/A
JC64-00218A
SHUTTER-M-TONER BOTTLE;CLP-300,POM HB,-,
SNA
#N/A
JC66-01095A
GEAR-AGITATOR BOTTLE;CLP-300,POM(DE8903)
SNA
#N/A
JC66-01139A
GEAR-AUGER A;CLP-300,POM,M0.6,Z89,T4.1,B
SNA
#N/A
JC66-01144A
SHAFT-AUGER;CLP-300,POM,L67,OD16,BLACK,SNA
#N/A
JC67-00135A
CAP-M-TONER BOTTLE;CLP-300,ABS HB,-,PI59
SNA
#N/A
JC92-01711A
PBA SUB-CRUM_M;CLP-300,SEC,KOREA,CRUM_M,
SNA
#N/A
JC92-01712A
PBA SUB-CRUM_C;CLP-300,SEC,KOREA,CRUM_C,
SNA
#N/A
JC92-01713A
PBA SUB-CRUM_K;CLP-300,SEC,KOREA,CRUM_K,
SNA
#N/A
JC96-04001A
ELA UNIT-CONNECTOR;CLP-300,SEC,EXPORT,-,
SA
#N/A
JC97-02688A
MEA UNIT-PICK UP GEAR;CLP-300,SEC,WORLD,
SA
#N/A
6601-001384
BEARING-BALL;676ZZ,ID6,OD10,L3,GCr 15 +
SNA
#N/A
6902-000288
BAG PE;LDPE,T0.05,W250,L450,TRP,8,2SNA
#N/A
JC68-01765A
LABEL-POP;CLP-300,DSH,YUPO,0.08,360,154,
SNA
#N/A
0201-001235
ADHESIVE-TS;DEH-390D,RED,400,SNA
#N/A
JC99-01896A
PAA MAIN-PACKING;CLP-300,SAMSUNG,EXPORT,
SNA
#N/A
JC64-00260C
HANDLE-BOTTLE M;CLP-300,ABS,T5.4,-,L43.6
SNA
#N/A
JC99-01897B
PAA WOOD-LABEL(SEE);CLP-300/SEE,EU,GOGH,
SNA
#N/A
JC64-00260D
HANDLE-BOTTLE C;CLP-300,ABS,T5.4,-,L43.6
SNA
#N/A
JC99-01898J
INA-ACCESSORY;CLP-300/XSG,SAMSUNG,-,GOGH
SNA
#N/A
0202-001240
SOLDER-WIRE;HSE-01,-,D3,SN/0.5CU/0.03NI/
SNA
#N/A
JC63-00894A
COVER-INNER;CLP-300,ABS,T2.0,PI 56,-,HB,
SNA
#N/A
0202-001459
SOLDER-CREAM;S3X58-M405,-,D20~38§-,96.5SS
SNA
#N/A
JC68-01564B
MANUAL-INSTALL;CLP-300,SEC,10 ,GOGH,M150
SNA
#N/A
JC92-01707B
PBA MAIN-GOGH_NET;CLP-300,SEC,KOREA,GDI,
SA
#N/A
JC64-00260A
HANDLE-M-BOTTLE;CLP-300,ABS,T5.9,W32.3,L
SNA
#N/A
JC66-01049A
GEAR-OPC DRIVE;CLP-300,POM,M0.6/M0.6,Z53
SA
#N/A
JC39-00484A
CBF HARNESS-SMPS;CLP-300,WIRE HARNESS,UL
SA
#N/A
JC39-00485A
CBF HARNESS-HVPS;CLP-300,WIRE HARNESS,UL
SA
#N/A
JC67-00135B
CAP-TONER BOTTLE C;CLP-300,ABS HB,T10.87
SNA
#N/A
6902-000775
BAG PE;HDPE,T0.015,W1000,L900,TRP,28,0,
SNA
#N/A
0201-001162
ADHESIVE-CYA;LOCTITE403,NTR,1250,20G
SNA
#N/A
JC61-01466A
FRAME-M-T2 BASE;CLP-300,PC+ABS,-,HB,BLAC
SNA
#N/A
JC61-01468A
GUIDE-P-T2 OUTPUT;CLP-300,SECC,T0.6,-,22
SNA
#N/A
JC61-01677A
SPRING ETC-RETURN;CLP-300,SUS304,¡Ë0.65,S
SNA
#N/A
JC66-01084A
SHAFT-M-AUGER OPC;CLP-300,ABS+GF20%,L250
SNA
#N/A
JC66-01086A
GEAR-DRUM OPC;CLP-300,PC(LF1025),M0.6,Z9
SNA
#N/A
JC66-01088A
SHAFT-OPC;CLP-300,SUS303,L284.5,OD6,-,-,
SNA
#N/A
JC66-01113A
GEAR-IDLE M08Z30R;CLP-300,POM (M90-44),M
SNA
#N/A
JC69-01016A
CUSHION-CASSETTE IN;CLP-300,HONEY PAD,T3
SNA
#N/A
JC74-00011A
MPR-PAD KNOCK UP MP;ML-6060A,CR+CORK,10*
O1109
SA
#N/A
JC39-00487A
CBF HARNESS-OPE;CLP-300,WIRE HARNESS,UL1
SA
#N/A
JC66-01124A
GEAR-IDLE OPC;CLP-300,POM (M90-44),M0.6/
SNA
#N/A
JC61-01500A
BRACKET-P-CLEANING ITB;CLP-300,SECC,1.6T
SNA
#N/A
JC61-01496A
HOUSING-M-CLEANING OPC;CLP-300,ABS GF 20
SNA
#N/A
JC39-00486A
CBF HARNESS-BLDC;CLP-300,WIRE HARNESS,UL
SA
#N/A
JC39-00580A
CBF HARNESS-DEVE_HOME;CLP-300,WIRE HARNE
SA
#N/A
JC61-01493A
FRAME-M-RIGHT OPC;CLP-300,ABS+GF20%,-,-,
SNA
#N/A
JC66-01299A
SHAFT-AUGER SUPPLY M;CLP-300,ABS GF20% G
SNA
#N/A
JC61-01529A
HOLDER-M-CRUM;CLP-300,ABS(XR-409),T2.0,W
SNA
#N/A
JC66-01074A
LEVER-M-RELEASE R;CLP-300,ABS+GF20%,T2.0
SNA
#N/A
JC61-01669A
GUIDE-M-SENSOR L;CLP-300,PS,T10.29,W11.7
SNA
#N/A
JC66-01069A
GEAR-CLUTCH DEVE CAM;CLP-300,POM,M0.6,Z2
SA
SA : SERVICE AVAILABLE SNA : SERVICE not AVAILABLE DNA : DELIVERY not AVAILABLE
Drawer#
SEC-Code
Description & Specification
Location Service
#N/A
JC73-00220A
RUBBER-BELT BLACK;CLP-300,NBR,0.7T,-,22,
SNA
#N/A
JC72-00382B
PMO-BUSHING FEED;ML-1710,POM(DERLIN 8903
O1102
SA
#N/A
JC46-00257A
S/W APPLICATION-CD;-,CLP-300,PRT DRV,1.0
SNA
#N/A
JC39-00494A
CBF HARNESS-REGI_EMT;CLP-300,WIRE HARNES
SA
#N/A
JC61-01675A
SPRING ETC-AUGER;CLP-300,SUS304,¡Ë1.2,-,S
SNA
#N/A
JC61-01676A
SPRING ETC-AUGER K;CLP-300,SWP-B,¡Ë1.2,IS
SNA
#N/A
JC72-01384A
SPONGE-CAP BOTTLE;CLP-300,POLYURETHANE F
SNA
#N/A
JC66-01140A
GEAR-AUGER B;CLP-300,POM,M0.6,Z56,T4.1,W
SNA
#N/A
JC66-01141A
GEAR-AUGER Z15;CLP-300,POM,M0.6,Z15,T3.5
SNA
#N/A
JC66-01301A
LEVER-COVER OPEN;CLP-300,PET+GF30,2.0,24
SNA
#N/A
JC70-50901A
IPR-IPM BUSHING DEV R;ML-5000,BRONZE,-,D
SNA
#N/A
JC94-01153A
PHANTOM AU JC92-01707B
SNA
#N/A
JC72-41105A
PMO-BUSHING DEV;ML-5000,POM,NTR,-,-,-,-,
SNA
#N/A
JC66-00720A
SHAFT-P-CORE;ML-1750,SECC 1.2T,203,-,-,O1068
SA
#N/A
JC63-00897A
COVER-M-WIRE;CLP-300,ABS,T2.0,W18.9,L133
SNA
#N/A
JC33-00018A
SOLENOID-TONER;-,CLP-300,DC24V,120§Ù¡¾10SN
SNA
#N/A
JC64-00229A
HANDLE-LOCK;CLP-300,ABS,T34.26,W39.3,L83
SNA
#N/A
JC68-01245A
MANUAL-WARRANTY CARD;COMMON,XSG,ARABIC,U
SNA
#N/A
3711-000198
HEADER-BOARD TO CABLE;1WALL,3P,1R,2.5MM,
SA
#N/A
JC92-01710A
PBA SUB-CRUM_Y;CLP-300,SEC,KOREA,CRUM_Y,
SNA
#N/A
JC72-01389A
SPONGE-CRUM;CLP-300,PORON,-,T2,W8,L12,-,
SNA
#N/A
JC61-01777A
HOLDER-BLADE ITB;CLP-300,PC,-,W10,L17.2,
SNA
#N/A
JC67-00134A
TANK-M-TONER BOTTLE BK;CLP-300,ABS HB,-,
SNA
#N/A
JC97-01401A
MEA UNIT-TERMINAL:TR;ML-5000A,SAMSUNG,KO
SA
#N/A
JC97-02638A
MEA UNIT-TERMINAL GND;CLP-300,SEC,EXPORT
SA
#N/A
JC97-02639A
MEA UNIT-FU TERMINAL;CLP-300,SEC,EXPORT,
SA
#N/A
JC97-02640A
MEA UNIT-REGIACTUATOR;CLP-300,SEC,EXPORT
SA
#N/A
JC97-02641A
MEA UNIT-EXIT ROLLER;CLP-300,SEC,EXPORT,
SA
#N/A
JC68-01154A
LABEL(R)-POP(A);COMMON,-,PC+HOLOGRAM,T0.
SNA
#N/A
JC68-01825A
LABEL-CAUTION;CLP-300,SEC,WHITE POLY,-,W
SNA
#N/A
JC69-01014A
CUSHION-MAIN BOTTOM;CLP-300,EPP,87,502,4
SNA
#N/A
JC63-00845A
COVER-M-RIGHT SIDE;CLP-300,ABS FR,T2.5,2
SA
#N/A
JC69-00919B
BOX(P)-MAIN;CLP-300,OFFSET4,A-1,515,424,
SA
#N/A
JC96-03590A
ELA UNIT-MAIN LINE;CLP-300,SEC,WORLD,220
SNA
#N/A
0202-001492
SOLDER-WIRE FLUX;HSE-02 LFM48 SR-34 S,-,
SNA
#N/A
0203-000007
TAPE-FILAMENT;3M,T0.15,W18,L55M,TRP
SNA
#N/A
0203-001100
TAPE-OPP MASKING;OPP/W75/CLR,T0.05,W75,L
SNA
#N/A
0203-001159
TAPE-FILAMENT;#8915,T0.15,W12,L55000,CLR
SNA
#N/A
0204-000469
THINNER;#4662,-,0.795,SNA
#N/A
0204-002978
FLUX;KSP-70M,-,84%,FLUX,SPRAY
SNA
#N/A
0205-001214
GREASE;LUBTECH FF 662,WHITE,SNA
#N/A
1103-001273
IC-EEPROM;24C64A,64Kbit,8Kx8Bit,DIP,8P,9
SA
#N/A
2801-003886
CRYSTAL-UNIT;12MHz,50ppm,28-AAA,16pF,50o
SNA
#N/A
3711-000164
HEADER-BOARD TO CABLE;1WALL,2P,1R,2.5mm,
SNA
#N/A
3711-000203
HEADER-BOARD TO CABLE;1WALL,2P/3P,1R,7.9
SA
#N/A
3711-002410
HEADER-BOARD TO CABLE;BOX,10P,2R,2mm,STR
SNA
#N/A
3711-003035
HEADER-BOARD TO CABLE;BOX,14P,2R,2mm,STR
SA
#N/A
3711-003204
HEADER-BOARD TO CABLE;BOX,24P,2R,2mm,STR
SA
#N/A
3711-003340
HEADER-BOARD TO CABLE;BOX,16P,2R,2mm,STR
SA
#N/A
3711-003408
HEADER-BOARD TO CABLE;BOX,2P,1R,2mm,STRA
SNA
#N/A
3722-002303
JACK-USB;4P/1C,AU30U,BLK,ANGLE,B TYPE
SA
#N/A
6902-000732
BAG PE;LDPE,T0.1,W120,L200,TRP,0,0,SNA
#N/A
6902-000734
BAG PE;LDPE,T0.1,W140,L250,TRP,-,-,SNA
#N/A
JB68-00073A
LABEL(R)-BAR CODE;SF-3000,PY,38X6.5,T0.1
SNA
#N/A
JB68-00916A
LABEL RATING-BLANK;SF-340,SEC,TETRON,0.0
SNA
#N/A
JC02-00052A
TONER-MAGENTA;CLP-300,SAM-79GZ-K1,MAGENT
SNA
#N/A
JC02-00053A
TONER-CYAN;CLP-300,SAC-79GZ-K1,CYAN,8.5?
SNA
SA : SERVICE AVAILABLE SNA : SERVICE not AVAILABLE DNA : DELIVERY not AVAILABLE
Drawer#
SEC-Code
Description & Specification
Location Service
#N/A
JC02-00055A
TONER-YELLOW;CLP-300,SAY-79GZ-K1,YELLOW,
SNA
#N/A
JC39-00483A
CBF HARNESS-LSU;CLP-300,WIRE HARNESS,UL1
SA
#N/A
JC39-00496A
CBF HARNESS-LSU_GND;CLP-300,WIRE HARNESS
SA
#N/A
JC62-00261A
SEAL-SHUTTER A;CLP-300,PE FOAM,-,T10,ID3
SNA
#N/A
JC63-00895A
COVER-INNER BK;CLP-300,ABS,T2.0,R75,-,HB
SNA
#N/A
JC63-01046A
SHEET-AGITATOR;CLP-300,PET,T0.125,W25.5,
SNA
#N/A
JC63-01047A
SHEET-AGITATOR BK;CLP-300,PET,T0.125,W35
SNA
#N/A
JC64-00260B
HANDLE-BOTTLE Y;CLP-300,ABS,T5.4,-,L43.6
SNA
#N/A
JC66-01145A
SHAFT-SPRING;CLP-300,POM,L16.5,OD11.5,BL
SNA
#N/A
JC66-01146A
SHAFT-AUGER K;CLP-300,POM,L70.3,OD10,WHI
SNA
#N/A
JC67-00131A
TANK-M-TONER BOTTLE Y;CLP-300,ABS HB,-,P
SNA
#N/A
JC67-00135C
CAP-TONER BOTTLE M;CLP-300,ABS HB,T10.87
SNA
#N/A
JC67-00136A
CAP-M-TONER BOTTLE BK;CLP-300,ABS HB,-,P
SNA
#N/A
JC67-00137A
CAP-M-CRUM BOTTLE;CLP-300,ABS HB,-,PI52,
SNA
#N/A
JC67-00140A
CAP-M-CRUM BOTTLE BK;CLP-300,ABS(HF-0660
SNA
#N/A
JC67-00141A
CAP-M-CRUM BOTTLE C;CLP-300,ABS(HF-0660I
SNA
#N/A
JC67-00142A
CAP-M-CRUM BOTTLE M;CLP-300,ABS(HF-0660I
SNA
#N/A
JC67-00145A
CAP-M-TONER;CLP-300,PP,T4.5,ID16.7,OD19,
SNA
#N/A
JC67-00187A
CAP-BOTTLE Y;CLP-300,PET,T0.65,W64.53,L5
SNA
#N/A
JC67-00188A
CAP-BOTTLE BK;CLP-300,PET,T0.65,R39.1,L5
SNA
#N/A
JC68-01032A
MANUAL-REGISTRATION CARD;COMMON,XGE,ARAB
SNA
#N/A
JC68-01381B
LABEL(R)-PPID(DEVE);COMMON,DELL,ART,0.05
SNA
#N/A
JC68-01584A
LABEL(P)-BLANK 90*25;CLP-510,SEE,ART 100
D2120
SA
#N/A
JC68-01707A
LABEL-FUNCTION;CLP-300,-,YUPO,T0.2,W10,L
SNA
#N/A
JC68-01805A
LABEL-FUNCTION;CLP-300,SEC,YUPO,T0.2,W10
SNA
#N/A
JC68-10932A
LABEL(P)-BLANK(ML);ML-85,ART,70X60,G100,
SNA
#N/A
JC69-01014B
CUSHION-MAIN TOP;CLP-300,EPP,184,502,411
SNA
#N/A
JC96-04002A
ELA HOU-REGI_EMP;CLP-300,KOREA,KOREA,REG
SA
#N/A
JC97-02642A
MEA UNIT-EMPTY ACT;CLP-300,SEC,EXPORT,-,
SA
#N/A
JC97-02647A
MEA UNIT-PICKUP ROLL;CLP-300,SEC,EXPORT,
SA
#N/A
JG61-40001A
FOOT-SF4000;SF4000,CR,-,BLK,CR,3,-,F1017
SA
#N/A
0201-001183
ADHESIVE-AA;ARON ALPHA #202F,NTR,100,20G
SNA
#N/A
0205-001056
GREASE-GRAPHITE;CRS841,WHT,SNA
#N/A
0205-001067
GREASE-GRAPHITE;NYOGEL 756G,HYDRO CARBON
SNA
#N/A
0401-000116
DIODE-SWITCHING;MMSD914T1,100V,200MA,SOD
SNA
#N/A
0407-000122
DIODE-ARRAY;KDS226,80V,300mA,C2-3,SOT-23
SA
#N/A
0501-000462
TR-SMALL SIGNAL;MMBT2907A,PNP,350mW,SOTSA
#N/A
0505-001326
FET-SILICON;SI2308DS,N,60V,2A,0.22OHM,1.
SA
#N/A
0601-001226
LED;SMD,RED,1.2x0.8mm,660nm,1.6x0.8mm
SA
#N/A
0601-001383
LED;ROUND,RED,3.0MM,700NM
SNA
#N/A
0803-000634
IC-TTL;74LS07,BUFFER/DRIVER,SOP,14,150MI
SA
#N/A
0904-001989
IC-USC;ISP1582BS,-,HVQFN56,56P,8X8X0.85M
SA
#N/A
1105-001535
IC-DRAM;M12L128168A-7T,-,128MBIT,4X2MX16
SA
#N/A
1107-001302
IC-FLASH MEMORY;29LV800,1Mx8/512Kx16,TSO
SA
#N/A
1202-000164
IC-VOLTAGE COMP.;393,SOP,8P,150MIL,DUAL,
SA
#N/A
1203-001455
IC-POSI.FIXED REG.;1117,DPAK,3P,265MIL,P
SA
#N/A
1203-002233
IC-RESET;XC61F,SOT-23,3P,-,PLASTIC,0.7/1
SNA
#N/A
1203-003739
IC-DC/DC CONVERTER;MVPG31,DFN,12P,4X3MM,
SNA
#N/A
1205-002339
IC-CLOCK GENERATOR;CY25811SC,SOIC,8P,150
SA
#N/A
2007-000066
R-CHIP;20Kohm,1%,1/10W,TP,1608
SA
#N/A
2007-000067
R-CHIP;15Kohm,1%,1/10W,TP,1608
SA
#N/A
2007-000077
R-CHIP;470ohm,5%,1/10W,TP,1608
SA
#N/A
2007-000080
R-CHIP;2Kohm,5%,1/10W,TP,1608
SA
#N/A
2007-000082
R-CHIP;3.3Kohm,5%,1/10W,TP,1608
SA
#N/A
2007-000094
R-CHIP;22Kohm,5%,1/10W,TP,1608
SA
#N/A
2007-000097
R-CHIP;47Kohm,5%,1/10W,TP,1608
SA
#N/A
2007-000105
R-CHIP;200Kohm,5%,1/10W,TP,1608
SA
SA : SERVICE AVAILABLE SNA : SERVICE not AVAILABLE DNA : DELIVERY not AVAILABLE
Drawer#
SEC-Code
Description & Specification
Location Service
#N/A
2007-000113
R-CHIP;33ohm,5%,1/10W,TP,1608
SA
#N/A
2007-000123
R-CHIP;1.5Kohm,5%,1/10W,TP,1608
SA
#N/A
2007-000134
R-CHIP;33Kohm,5%,1/10W,TP,1608
SA
#N/A
2007-000239
R-CHIP;1.5Kohm,1%,1/10W,TP,1608
SA
#N/A
2007-000309
R-CHIP;10ohm,5%,1/10W,TP,1608
SA
#N/A
2007-000402
R-CHIP;150ohm,5%,1/10W,TP,1608
SA
#N/A
2007-000475
R-CHIP;1Mohm,1%,1/10W,TP,1608
SA
#N/A
2007-000539
R-CHIP;200ohm,5%,1/10W,TP,1608
SA
#N/A
2007-000729
R-CHIP;300ohm,5%,1/10W,TP,1608
SA
#N/A
2007-000965
R-CHIP;5.1Kohm,5%,1/10W,TP,1608
SA
#N/A
2007-001056
R-CHIP;6.2Kohm,5%,1/10W,TP,1608
SA
#N/A
2007-002901
R-CHIP;12.1Kohm,1%,1/10W,TP,1608
SA
#N/A
2007-007239
R-CHIP;31.6Kohm,1%,1/10W,TP,1608
SNA
#N/A
2007-008371
R-CHIP;280Kohm,1%,1/10W,TP,1608
SNA
#N/A
2011-001011
R-NET;10Kohm,5%,1/16W,L,CHIP,8P,TP,3.2x1
SNA
#N/A
2011-001261
R-NET;33ohm,5%,1/16W,L,CHIP,8P,TP,2.0x1.
SA
#N/A
2203-000236
C-CER,CHIP;0.1nF,5%,50V,C0G,1608
SA
#N/A
2203-000384
C-CER,CHIP;0.015nF,5%,50V,C0G,1608
SA
#N/A
2203-000426
C-CER,CHIP;0.018nF,5%,50V,C0G,1608
SA
#N/A
2203-000491
C-CER,CHIP;2.2nF,10%,50V,X7R,1608
SA
#N/A
2203-005384
C-CER,CHIP;4700nF,+80-20%,10V,Y5V,2012
SA
#N/A
2203-005819
C-CER,CHIP;1000nF,+80-20%,16V,Y5V,-,1608
SNA
#N/A
2203-006474
C-CER,CHIP;22000nF,20%,6.3V,X5R,2012
SA
#N/A
2203-006646
C-CER,CHIP;10000nF,10%,6.3V,X5R,2012
SA
#N/A
2401-000042
C-AL;100uF,20%,16V,GP,TP,6.3x7,5
SA
#N/A
2401-000207
C-AL;100uF,20%,50V,WT,TP,8x12,5
SNA
#N/A
2401-002300
C-AL;47uF,20%,50V,GP,TP,6.3x11,5
SA
#N/A
2402-001049
C-AL,SMD;10uF,20%,16V,GP,TP,3.3x3.3x5.4
SA
#N/A
2703-000300
INDUCTOR-SMD;1uH,10%,1608
SA
#N/A
2703-002055
INDUCTOR-SMD;2.2UH,20%,6363
SNA
#N/A
2901-001178
FILTER-EMI SMD;25V,2A,-,100000pF,2x1.25x
SA
#N/A
3301-000325
BEAD-SMD;60ohm,3.2x2.5x1.3mm,400mA,TP,,,
SNA
#N/A
3301-001122
BEAD-SMD;600ohm,1.6x0.8x0.8mm,TP,-,SNA
#N/A
3301-001240
BEAD-SMD;120ohm,1608,200mA,,393ohm/305MH
SNA
#N/A
3404-000165
SWITCH-TACT;12V,50mA,160gf,6x6mm,SPST
D2158
SA
#N/A
3711-003409
HEADER-BOARD TO CABLE;BOX,3P,1R,2mm,STRA
SNA
#N/A
3711-003410
HEADER-BOARD TO CABLE;BOX,4P,1R,2mm,STRA
SNA
#N/A
3711-003411
HEADER-BOARD TO CABLE;BOX,5P,1R,2mm,STRA
SNA
#N/A
6044-001035
RING-ETC;ID2.2,OD6.4,T3,BLK,STS304
SNA
#N/A
JC13-00031B
IC ASIC-CHORUSM;CHORUSM,SCX-4920N_VE,496
SA
#N/A
JC39-00036A
CBF HARNESS-OPE GND;SF-5100,#18,UL 1007,
SA
#N/A
JC39-00490A
WIRE HARNESS-WASTE_T;CLP-300,WIRE HARNES
SA
#N/A
JC39-00492A
CBF HARNESS-PTL;CLP-300,WIRE HARNESS,UL1
SNA
#N/A
JC39-00495A
CBF HARNESS-EXIT;CLP-300,WIRE HARNESS,UL
SA
#N/A
JC39-00577A
CBF HARNESS-DEVE_ITB;CLP-300,WIRE HARNES
SNA
#N/A
JC41-00300A
PCB MAIN-GOGH_GDI;CLP-300,FR-4,6L,-,1.6T
SNA
#N/A
JC60-00014A
FLANGE-M-DRUM OPC;CLP-300,PC(LF1025),W11
SNA
#N/A
JC60-00015A
SPACER-M-DR G;CLP-300,KL4540,-,ID6.03,OD
SNA
#N/A
JC61-00424A
BUSH-4;ML-9400W,NTN B-F4-42,-,-,-,NTR,K2867
SA
#N/A
JC61-01120B
PLATE-CRUM;CLP-300,C5210P,0.15,W3,L5.2,SNA
#N/A
JC61-01158A
PLATE-M-KNOCK_UP;ML-1610,HIPS HB,T2,W80,
K5002
SA
#N/A
JC61-01281A
BRACKET-P-BAR_PICK_UP;ML-1610,SECC,T1.0,
SNA
#N/A
JC61-01467A
PLATE-P-T2 GROUND;CLP-300,C5210P 1/2H TA
SNA
#N/A
JC61-01469A
HOLDER-M-LOCATE SHAFT;CLP-300,POM (M90-4
SNA
#N/A
JC61-01470A
GUIDE-P-T2 INPUT;CLP-300,SECC,T0.6,-,230
SNA
#N/A
JC61-01492A
FRAME-M-LEFT OPC;CLP-300,ABS+GF20%,-,-,B
SNA
#N/A
JC61-01501A
PLATE-P-EARTH OPC;CLP-300,C5210P,T0.2,ID
SNA
SA : SERVICE AVAILABLE SNA : SERVICE not AVAILABLE DNA : DELIVERY not AVAILABLE
Drawer#
SEC-Code
Description & Specification
Location Service
#N/A
JC61-01508A
FRAME-M-DEVE YELLOW;CLP-300,ABS+GF20%,GR
SNA
#N/A
JC61-01509A
FRAME-M-DEVE MAGENTA;CLP-300,ABS+GF20%,G
SNA
#N/A
JC61-01510A
FRAME-M-DEVE CYAN;CLP-300,ABS+GF20%,GR40
SNA
#N/A
JC61-01511A
FRAME-M-DEVE BLACK;CLP-300,ABS+GF20%,GR4
SNA
#N/A
JC61-01512A
HOLDER-M-DEVE YELLOW L;CLP-300,ABS+GF20%
SNA
#N/A
JC61-01516A
GUIDE-M-DEVE;CLP-300,ABS+GF20%,GR4020,22
SNA
#N/A
JC61-01518A
PLATE-P-SUPPLY ROLLER;CLP-300,SUS 301-CS
SNA
#N/A
JC61-01519A
PLATE-P-DEVE ROLLER;CLP-300,SUS 301-CSP
SNA
#N/A
JC61-01520A
FRAME-M-DEVE MAIN;CLP-300,ABS GF20%,GR-4
SNA
#N/A
JC61-01526A
GUIDE-M-BUSH IDL ITB R;CLP-300,POM M90-4
SNA
#N/A
JC61-01527A
HOLDER-P-SEAL DEVE L;CLP-300,SUS301-CSP
SNA
#N/A
JC61-01528A
HOLDER-P-SEAL DEVE R;CLP-300,SUS301-CSP
SNA
#N/A
JC61-01561A
HOLDER-M-DEVE ROLLER;CLP-300,POM M90-44,
SNA
#N/A
JC61-01562A
GUIDE-M-DRIVE ITB;CLP-300,POM(M90-44),-,
SNA
#N/A
JC61-01573A
HOLDER-SUPPORT;CLP-300,ABS,T14.5,W26.5,L
SNA
#N/A
JC61-01576A
BUSH-SHAFT;CLP-300,POM,ID3.0,OD4.5,T3.5,
SNA
#N/A
JC61-01670A
GUIDE-M-SENSOR R;CLP-300,PS,T10.29,W11.7
SNA
#N/A
JC61-01671A
GUIDE-M-SENSOR BK R;CLP-300,PS,T10,W13.4
SNA
#N/A
JC61-01672A
GUIDE-M-SENSOR BK L;CLP-300,PS,T10,W13.4
SNA
#N/A
JC61-01673A
BLADE-CLEANING ITB;CLP-300,POLYURETHANE,
SNA
#N/A
JC61-01684A
BLADE-SENSOR;CLP-300,PET FILM,-,W6.3*L9.
SNA
#N/A
JC61-01687A
SPRING ETC-LOCK;CLP-300,PW-2,PI1.3,-,-,L
SNA
#N/A
JC61-01700A
GUIDE-WASTE;CLP-300,PC,-,31,41,TRANSPARE
SNA
#N/A
JC61-01706A
STUD-GEAR ITB;CLP-300,SUM22L,-,-,-,-,OD6
SNA
#N/A
JC61-01750A
BRACKET-P_GUIDE PR;CLP-300,SUS,T1.0,W232
SNA
#N/A
JC61-01751A
GUIDE-P_PAPER PR;CLP-300,SUS304,T0.1,W21
SNA
#N/A
JC61-01753A
PLATE-_P-DEVE SUPPORT;CLP-300,STSC301-CS
SNA
#N/A
JC61-01775A
BRACKET-CAM BAR;CLP-300,SECC,T1.2,W4.5,L
SNA
#N/A
JC61-70929A
SPRING ETC-HV LARGE;ML-5000A,SUS304-WPB,
Z4437
SA
#N/A
JC62-00211A
SEAL-DRUM OPC;CLP-300,URETHANE FILM,-,T0
SNA
#N/A
JC62-00215A
SEAL-SIDE DEVE;CLP-300,PORON LE20,BLACK,
SNA
#N/A
JC62-00216A
SEAL-BRACKET OPC;CLP-300,EPDM,-,T2.7,W3,
SNA
#N/A
JC62-00226A
SEAL-DOCTOR BLADE;CLP-300,EPDM,-,T4.0,W4
SNA
#N/A
JC62-00230A
SEAL-SIDE RIGHT OPC;CLP-300,POLYURETHANE
SNA
#N/A
JC62-00231A
SEAL-SIDE LEFT OPC;CLP-300,POLYURETHANE
SNA
#N/A
JC62-00234A
SEAL-DEVE BLOCK;CLP-300,POLYURETHANE,-,3
SNA
#N/A
JC62-00235A
SEAL-DEVE ROLLER;CLP-300,PET Film,-,0.07
SNA
#N/A
JC62-00236A
SEAL-DEVE FRONT;CLP-300,PET FILM,-,0.075
SNA
#N/A
JC62-00240A
SEAL-AUGER;CLP-300,PORON ,BLACK,T5.0,ID4
SNA
#N/A
JC62-00241A
SEAL-COVER DUCT;CLP-300,PE FOAM,-,T2.0,W
SNA
#N/A
JC62-00256A
SEAL-FRAME WASTE OPC;CLP-300,PORON LE-20
SNA
#N/A
JC62-00260A
SEAL-CAP CRUM;CLP-300,Polyurethane Foam(
SNA
#N/A
JC62-00262A
SEAL-WASTE;CLP-300,PE FORM,-,T3.0,W4,L13
SNA
#N/A
JC62-00269A
SEAL-COVER FRONT;CLP-300,PE FOAM,-,T2.0,
SNA
#N/A
JC62-00270A
SEAL-COVER BOTTOM;CLP-300,POLYURETHANE F
SNA
#N/A
JC62-00271A
SEAL-COVER DEV K;CLP-300,PE FOAM,-,T3.0,
SNA
#N/A
JC62-00272A
SEAL-LSU REAR;CLP-300,URETHAN FILM,NTR,T
SNA
#N/A
JC62-00273A
SEAL-DEVE ROLLER K;CLP-300,PET FILM,-,T0
SNA
#N/A
JC62-00274A
SEAL-SIDE GAP OPC;CLP-300,POLYURETHAN FO
SNA
#N/A
JC62-00275A
SEAL-BLADE;CLP-300,PE FOAM,-,T3.0,W3,L8.
SNA
#N/A
JC62-00279A
SEAL-SENSOR BK;CLP-300,FLOCKING(DOBIRU),
SNA
#N/A
JC62-00280A
SEAL-SENSOR Y;CLP-300,FLOCKING(DOBIRU),B
SNA
#N/A
JC62-00306A
SEAL-CAP DUCT;CLP-300,FLOCKING,-,T0.5,W8
SNA
#N/A
JC62-00307A
SEAL-SENSOR;CLP-300,FLOCKING,-,T0.5,W13.
SNA
#N/A
JC62-00308A
SEAL-DOCTOR BLADE S;CLP-300,EPDM,-,T2.0,
SNA
#N/A
JC62-00320A
SEAL-WASTE F;CLP-300,PE FOAM,GRAY,2.0T,W
SNA
#N/A
JC62-00321A
SEAL-WASTE R;CLP-300,PE FOAM,GRAY,2.0T,w
SNA
SA : SERVICE AVAILABLE SNA : SERVICE not AVAILABLE DNA : DELIVERY not AVAILABLE
Drawer#
SEC-Code
Description & Specification
Location Service
#N/A
JC62-00324A
SEAL-WASTE B;CLP-300,POLY-URETHANE(SHL),
SNA
#N/A
JC62-00341A
SEAL-WASTE EXIT;CLP-300,PORON LE-20 + PE
SNA
#N/A
JC62-00342A
SEAL-SIDE CLN OPC;CLP-300,POLYURETHANE F
SNA
#N/A
JC62-00343A
SEAL-SENSOR TOP;CLP-300,EPDM,-,T2.5,W4,L
SNA
#N/A
JC63-00853A
COVER-M-TONER BOTTLE;CLP-300,ABS HB HF-0
SNA
#N/A
JC63-00858A
COVER-M-WASTE OPC;CLP-300,ABS,T2,W15.8,L
SNA
#N/A
JC63-00883A
COVER-M-WASTE;CLP-300,PC(141R),T2.0,W77,
SNA
#N/A
JC63-00898A
COVER-M-DEVE Y;CLP-300,ABS HF0660I,T1.5,
SNA
#N/A
JC63-00899A
COVER-M-DEVE M;CLP-300,ABS HF0660I,T1.5,
SNA
#N/A
JC63-00900A
COVER-M-DEVE C;CLP-300,ABS HF0660I,T1.5,
SNA
#N/A
JC63-00901A
COVER-M-DEVE K;CLP-300,ABS HF0660I,T1.5,
SNA
#N/A
JC63-01048A
SHEET-COVER HARNESS;CLP-300,PC,T0.125,W4
SNA
#N/A
JC63-01086A
SHEET-WASTE;CLP-300,PET,T0.188,W24,L24,B
SNA
#N/A
JC63-01087A
SHEET-LSU COVER;CLP-300,PC,T0.38,W17,L23
SNA
#N/A
JC63-01164A
SHEET-HOUSING REAR;CLP-300,PC,T0.38,W11.
SNA
#N/A
JC64-00217A
HANDLE-M-UNIT;CLP-300,ABS,7.0T,50.5,130,
SNA
#N/A
JC64-00276A
LOCKER-FRAME;CLP-300,PC,BLK,-,-,SNA
#N/A
JC66-00494A
GEAR-OPC ROLL CLEAN_Z18;CLP-500,POM,M0.8
SNA
#N/A
JC66-00604A
ROLLER-CHARGER CLEANING;CLP-500,URETHAN+
SNA
#N/A
JC66-00830A
ROLLER-M-EXIT FR;ML-1610,TEFLON,6.5,L22.
SNA
#N/A
JC66-01058A
LATCH-M-CLUTCH SPRING;CLP-300,POM,T1.2,D
SNA
#N/A
JC66-01072A
SHAFT-LOCATE;CLP-300,SUM 22+NI(COATING),
SNA
#N/A
JC66-01075A
LEVER-M-RELEASE L;CLP-300,ABS+GF20%,T2.0
SNA
#N/A
JC66-01081A
GEAR-RDCN T2 DRIVE;CLP-300,POM,M0.8/M0.8
SA
#N/A
JC66-01090A
GEAR-DEVE ROLLER;CLP-300,POM DE8903,M0.6
SNA
#N/A
JC66-01091A
GEAR-SUPPLY ROLLER;CLP-300,POM DE588P,M0
SNA
#N/A
JC66-01092A
SHAFT-M-AUGER SUPPLY;CLP-300,ABS GF20% G
SNA
#N/A
JC66-01093A
SHAFT-M-BELT;CLP-300,POM(M90-44),24.8,¥ÕS
SNA
#N/A
JC66-01094A
LEVER-M-WASTE SENSOR;CLP-300,ABS,3.0T,18
SNA
#N/A
JC66-01099A
SHAFT-M-AUGER TONER Y;CLP-300,ABS GF20%
SNA
#N/A
JC66-01100A
SHAFT-M-AUGER TONER M;CLP-300,ABS GF20%
SNA
#N/A
JC66-01101A
SHAFT-M-AUGER TONER C;CLP-300,ABS GF20%
SNA
#N/A
JC66-01102A
SHAFT-M-AUGER TONER K;CLP-300,ABS GF20%
SNA
#N/A
JC66-01103A
LEVER-M-LOCK DEVE FRAME;CLP-300,ABS,2.0T
SNA
#N/A
JC66-01107A
GEAR-AUGER SUPPLY;CLP-300,POM DE588P,M0.
SNA
#N/A
JC66-01108A
GEAR-IDLE;CLP-300,POM DE8903,M0.6/M0.5,Z
SNA
#N/A
JC66-01109A
GEAR-AUGER TONER;CLP-300,POM DE588P,M0.5
SNA
#N/A
JC66-01114A
GEAR-DRIVE Z20;CLP-300,POM (DE588P),M0.8
SNA
#N/A
JC66-01115A
GEAR-WORM AGITATOR;CLP-300,PC-141R,-,-,SNA
#N/A
JC66-01116A
GEAR-IDLE M08Z30L;CLP-300,POM (M90-44),M
SNA
#N/A
JC66-01117A
GEAR-IDLE ITB;CLP-300,POM (M90-44),M0.8,
SNA
#N/A
JC66-01121A
LEVER-M-T2 HOLDER R;CLP-300,ABS+GF20%,T2
SNA
#N/A
JC66-01122A
LEVER-M-T2 HOLDER L;CLP-300,ABS+GF20%,T2
SNA
#N/A
JC66-01123A
GEAR-AUGER OPC;CLP-300,POM (M90-44),M0.5
SNA
#N/A
JC66-01125A
ROLLER-DEVE;CLP-300,NBR+ECO,OD10,L295.3,
SNA
#N/A
JC66-01126A
ROLLER-SUPPLY;CLP-300,Fur Brush,OD9.15,L
SNA
#N/A
JC66-01127A
DRUM-OPC;CLP-300,AL,ID58,OD60,L248,-,SNA
#N/A
JC66-01129A
ROLLER-DRIVE ITB;CLP-300,AL+EPDM,OD29.7,
SNA
#N/A
JC66-01130A
ROLLER-IDLE ITB;CLP-300,AL,OD30,L234,-,SNA
#N/A
JC66-01137A
GEAR-DRIVE ITB;CLP-300,PC(LF1025),M0.5,Z
SNA
#N/A
JC66-01142A
ROLLER-SLIDE A;CLP-300,POM,L10,OD10.2,BL
SNA
#N/A
JC66-01143A
ROLLER-SLIDE B;CLP-300,POM,L20,OD14,BLAC
SNA
#N/A
JC66-01230A
SHAFT-DEVE FRAME;CLP-300,SUS303,L28.4,¡ËS
SNA
#N/A
JC66-01295A
SHAFT-AUGER SUPPLY Y;CLP-300,ABS GF20% G
SNA
#N/A
JC66-01298A
SHAFT-AUGER SUPPLY C;CLP-300,ABS GF20% G
SNA
#N/A
JC66-01302A
SHAFT-HOUSING PICK UP;CLP-300,SUM22+NI C
SNA
#N/A
JC67-00143A
CAP-M-WASTE BOTTLE;CLP-300,LDPE(MB9205),
SNA
SA : SERVICE AVAILABLE SNA : SERVICE not AVAILABLE DNA : DELIVERY not AVAILABLE
Drawer#
SEC-Code
Description & Specification
Location Service
#N/A
JC67-00144A
TANK-M-WASTE;CLP-300,ABS(TR557A),T2.0,W1
SNA
#N/A
JC67-00162A
CAP-DUCT;CLP-300,NBR,T0.7,17.8,19.7,-,SNA
#N/A
JC67-00191A
CAP-DUMMY;CLP-300,ABS,-,-,L31.4,DM GRAY,
SNA
#N/A
JC70-10232A
IPR-PLATE SAW;ML-80,SUS304 CSP 1/2H,-,T0
O1099
SA
#N/A
JC70-40912A
ICT-SHAFT HV LARGE;ML-5000A,SWCH18A,-,¥÷
O1100
SA
#N/A
JC71-00009A
NPM-BUSHING DEV R;ML-6060,BRONZE,D7*12,SNA
#N/A
JC72-01004A
PMO-IDLE KNOCK UP MP;ML-2150,POM,BLK,-,M
P0041
SA
#N/A
JC73-00217A
RUBBER-BELT YELLOW;CLP-300,NBR,0.7T,-,22
SNA
#N/A
JC73-00221A
RUBBER-BELT WASTE OPC;CLP-300,NBR,L335.9
SNA
#N/A
JC92-01708A
PBA SUB-DEVE_JOINT;CLP-300,SEC,KOREA,DEV
SNA
#N/A
JC92-01721A
PBA SUB-REGI_EMPTY;CLP-300,SEC,KOREA,REG
SNA
#N/A
JC92-01722A
PBA SUB-WASTE_R;CLP-300,SEC,KOREA,WASTE_
SNA
#N/A
JC94-01119A
0
SNA
#N/A
JC94-01120A
0
SNA
#N/A
JC94-01121A
0
SNA
#N/A
JC94-01122A
0
SNA
#N/A
JC94-01123A
0
SNA
#N/A
JC94-01124A
0
SNA
#N/A
JC94-01125A
0.1
SNA
#N/A
JC94-01126A
0.1
SNA
#N/A
JC94-01129A
0.1
SNA
#N/A
JC94-01130A
0.2
SNA
#N/A
JC97-01788C
MEA UNIT-CLUTCH TONER;CLP-300,-,WORLD,M0
SNA
#N/A
JC97-02620A
MEA UNIT-SUS BLADE;CLP-300,SEC,WORLD,-,SNA
#N/A
JC97-02628A
MEA UNIT-T2 ROLLER;CLP-300,SEC,WORLD,-,SA
#N/A
JC97-02643A
MEA UNIT-BLADE OPC;CLP-300,SEC,EXPORT,-,
SNA
#N/A
JC97-02644A
MEA UNIT-CHARGE OPC;CLP-300,SEC,EXPORT,SNA
#N/A
JC97-02694A
MEA-GUIDE IDL ITB;CLP-300,SEC,WORLD,-,-,
SNA
#N/A
0407-000101
DIODE-ARRAY;DA204K,20V,100mA,C2-3,SOT-23
SA
#N/A
0501-000457
TR-SMALL SIGNAL;MMBT2222A,NPN,350mW,SOTSA
#N/A
0601-000003
LED;ROUND,RED/GRN,3.1MM,650/563NM,3.8X5.
SA
#N/A
0601-001138
LED-IR;ROUND,5mm,150mW,4V,950nm,BK
SNA
#N/A
0601-001908
LED;ROUND,RED,3MM,630NM,3.2X4.6MM
SNA
#N/A
0603-001021
PHOTO TR;NPN,20V,5V,20mA,75mW,TP
SA
#N/A
1103-001366
IC-EEPROM;34C02,2KBIT,256X8BIT,SOP,8P,5X
SNA
#N/A
2001-000831
R-CARBON;510OHM,5%,1/4W,AA,TP,2.4X6.4MM
SA
#N/A
2007-000033
R-CHIP;0ohm,5%,1/4W,TP,3216
SA
#N/A
2007-000070
R-CHIP;0ohm,5%,1/10W,TP,1608
SA
#N/A
2007-000078
R-CHIP;1Kohm,5%,1/10W,TP,1608
SA
#N/A
2007-000086
R-CHIP;5.6Kohm,5%,1/10W,TP,1608
SA
#N/A
2007-000090
R-CHIP;10Kohm,5%,1/10W,TP,1608
SA
#N/A
2007-000730
R-CHIP;300ohm,5%,1/4W,TP,3216
SA
#N/A
2007-001003
R-CHIP;510ohm,5%,1/4W,TP,3216
SNA
#N/A
2201-000021
C-CERAMIC,DISC;100NF,+80-20%,50V,Y5V,TP,
DNA
#N/A
2203-000189
C-CER,CHIP;100nF,+80-20%,25V,Y5V,1608
SA
#N/A
2203-000626
C-CER,CHIP;0.022nF,5%,50V,C0G,1608
SA
#N/A
2203-005249
C-CER,CHIP;100nF,10%,50V,X7R,1608
SNA
#N/A
2404-001102
C-TA,CHIP;33uF,20%,16V,GP,TP,6032,SNA
#N/A
3711-002001
HEADER-BOARD TO CABLE;BOX,20P,2R,2MM,STR
SA
#N/A
JC39-00491A
CBF HARNESS-WASTE_R;CLP-300,WIRE HARNESS
SNA
#N/A
JC41-00171C
PCB-PTL (1LAYER);SCX-4100,FR-1,1,-,1.6T,
SNA
#N/A
JC41-00201A
PCB-TONER_TX;CLP-500,FR-1,1L,-,1.2,15*10
SNA
#N/A
JC41-00296A
PCB SUB-ITB_JOINT;CLP-300,FR-1,1L,-,1.6T
SNA
#N/A
JC41-00298A
PCB SUB-TONER_CRUM;CLP-300,FR-4,2L,-,1.6
SNA
#N/A
JC41-00299A
PCB SUB-PANEL;CLP-300,FR-1,1L,-,1.6T,45*
SNA
#N/A
JC61-01471A
HOLDER-M-T2 ROLLER R;CLP-300,POM (M90-44
SNA
#N/A
JC61-01507A
PLATE-P-DOCTOR BLADE;CLP-300,SECC,1.2T,3
SNA
SA : SERVICE AVAILABLE SNA : SERVICE not AVAILABLE DNA : DELIVERY not AVAILABLE
Drawer#
SEC-Code
Description & Specification
Location Service
#N/A
JC61-01525A
GUIDE-M-BUSH IDL ITB L;CLP-300,POM M90-4
SNA
#N/A
JC61-01545A
BRACKET-P-CLEANING OPC;CLP-300,SECC,T1.2
SNA
#N/A
JC61-01575A
BLADE-P-DOCTOR;CLP-300,SUS,NATURAL,223*1
SNA
#N/A
JC61-01668A
COLLAR-M-CLUTCH;CLP-300,POM,ID11.4,OD13.
SNA
#N/A
JC61-01674A
BLADE-CLEANING OPC;CLP-300,POLY URETHANE
SNA
#N/A
JC66-01073A
GEAR-T2 ROLLER;CLP-300,POM,M0.8,Z28,-,WH
SA
#N/A
JC66-01098A
GEAR-CHARGE;CLP-300,POM (M90-44),M0.8,Z1
SNA
#N/A
JC66-01104A
ROLLER-TRANSFER;CLP-300,SUM22+HYBRID FOA
SNA
#N/A
JC66-01224A
GEAR-WORM CLUTCH;CLP-300,POM,M0.8,Z2,-,W
SNA
#N/A
JC66-01308A
ROLLER-CHARGE;CLP-300,NBR+ECO,D12,L230,SNA
#N/A
JC70-00525A
HUB-M-CLUTCH SPRING;CLP-300,POM,-,D13.4,
SNA
#N/A
JC71-10322B
NPR-EARTH OPC;-,ML-80,C5210P-1/2H,T0.2,SNA
#N/A
JC94-01118A
0
SNA
#N/A
JC94-01127A
0.1
SNA
#N/A
JC94-01128A
0.1
SNA
#N/A
0402-001189
DIODE-RECTIFIER;M4,400V,1A,TS-1,TP
SA
#N/A
1001-000170
IC-ANALOG SWITCH;MC14051BD,SPDT CMOS,SOP
SA
#N/A
1404-001141
THERMISTOR-NTC;5.6Kohm,5%,3200K,2.1mW/C,
SNA
#N/A
2001-000281
R-CARBON;100OHM,5%,1/8W,AA,TP,1.8X3.2MM
SA
#N/A
2007-000074
R-CHIP;100ohm,5%,1/10W,TP,1608
SA
#N/A
2007-000084
R-CHIP;4.7Kohm,5%,1/10W,TP,1608
SA
#N/A
2007-000119
R-CHIP;560ohm,5%,1/10W,TP,1608
SA
#N/A
2007-000122
R-CHIP;1.2Kohm,5%,1/10W,TP,1608
SA
#N/A
2007-000839
R-CHIP;39ohm,5%,1/10W,TP,1608
SA
#N/A
2007-000939
R-CHIP;47Kohm,1%,1/10W,TP,1608
SNA
#N/A
2007-007233
R-CHIP;61.9ohm,1%,1/10W,TP,1608
SNA
#N/A
2007-007550
R-CHIP;3.16Kohm,1%,1/10W,TP,1608
SNA
#N/A
2007-007613
R-CHIP;121ohm,1%,1/10W,TP,1608
SNA
#N/A
2203-000257
C-CER,CHIP;10nF,10%,50V,X7R,1608
SA
#N/A
2203-000440
C-CER,CHIP;1nF,10%,50V,X7R,1608
SA
#N/A
3711-005561
CONNECTOR-HEADER;BOX,5P,1R,2MM,SMD-S,SN,
SA
#N/A
3711-005596
HEADER-BOARD TO CABLE;BOX,3P,1R,2MM,SMDSNA
#N/A
3711-005851
HEADER-BATTERY;NOWALL,2P,1R,4.25MM,BATTE
SA
#N/A
3711-006032
CONNECTOR-HEADER;BOX,2P,1R,2MM,SMD-A,SN,
SNA
#N/A
JC41-00133A
PCB-SENSOR;SCX-5100,FR-1,1L,-,1.6T,22X12
SNA
#N/A
JC41-00202A
PCB-TONER_RX;CLP-500,FR-1,1L,-,1.2,15*10
SNA
#N/A
JC41-00295A
PCB SUB-DEVE_JOINT;CLP-300,FR-1,1L,-,1.6
SNA
9. Block Diagram
Service Manual
Samsung Electronics
10. Connection Diagram
Service Manual
Samsung Electronics
This Document can not be used without Samsung’s authorization.
11. Schematic Diagrams
11.1
Samsung Electronics
Service Manual
A
B
C
1
DGND
JTAG
C85
C86
CN9-1
35303-0850
8
7
6
5
4
3
2
1
DGND
nRD
nWR
nCS_BOOT
nCS_USB_DEVICE
nRST_USB_DEVICE
nRST_NIC
nCS_MODEM
nCS_USB_HOST
nADF_P_DET
nDREQ_USB_DEVICE
nADF_P_POS
nADF_P_REG
nDACK_USB_DEVICE
XI_MCLK
XO_MCLK
nRST_MODEM
nRST_USB_HOST
XI_VCLK
XO_VCLK
XI_RTC
XO_RTC
15pF
15pF
2
A12
B12
C11
C10
D10
A10
A9
A13
B13
H3
J5
H5
G4
H2
H4
G2
G3
U4
U5
R1
R2
R3
R4
P3
P4
T5
T2
T3
U3
T4
R5
AD5
AF5
AE5
AE4
AD4
nRESET
ADDR(1:23)
DATA(0:31)
33
RA16
10K
+3.3V
RA11
2.2nF
TEST JIG
C154
2.2nF
10K
0
C145
R77
R70
nTRST
TCK
TMS
TDI
TDO
nRD
nWR
nROMCS0
nROMCS1
nROMCS2_GPO_2
nROMCS3_GPO_3
nIOCS0
nIOCS1
nIOCS2
nIOCS3_GPO_4
nIOCS4_nIOCS4_CIP4E_GPO_5
nIOCS5_GPO_6
nWAIT0_GPI_0
nWAIT1_GPI_1
nDREQ0_nDREQ0_CIP4E_GPI_2
nDREQ1_nDREQ1_CIP4E_GPI_3
nDREQ2_nDREQ2_CIP4E_GPI_4
nDREQ3_nDREQ3_CIP4E_GPI_5
nDACK0_nDACK0_CIP4E_GPO_7
nDACK1_nDACK1_CIP4E_GPO_8
nDACK2_nDACK2_CIP4E_GPO_9
nDACK3_GPO_10
XI_MAIN
XOUT_MAIN
MAIN_FILTER
XI_VCLK
XOUT_VCLK
VCLK_FILTER
PCIPLL_CLK
RTC_XI
RTC_XOUT
3
4
JC13-00031A
U10-1
chrousm
5
6
nACK
PDE
nFAULT
SLCT_OUT
PERROR
BUSY
MDC_GPO_19
MDIO_GPIO1_31
COL_GPI_9
TX_CLK_GPI_10
MAC_TXD0_GPO_20
MAC_TXD1_GPO_21
MAC_TXD2_GPO_22
MAC_TXD3_GPO_23
TX_EN_GPO_24
TX_ERR_GPO_25
RX_ERR_GPI_11
CRS_GPI_12
RX_CLK_GPI_13
MAC_RXD0_GPI_14
MAC_RXD1_GPI_15
MAC_RXD2_GPI_16
MAC_RXD3_GPI_17
RX_DV_GPI_18
TXD0
TXD1
TXD2
TXD3_GPO_17
TXD4_GPO_18
RXD0
RXD1
RXD2
RXD3_GPI_7
RXD4_GPI_8
SCL
SDA
NF_CLE_GPIO2_0
NF_ALE_GPIO2_1
NF_nCE_GPIO2_2
NF_nRE_GPIO2_3
NF_nWE_GPIO2_4
NF_BOOT
NF_RnB_GPIO2_5
AB15
AF16
AE15
AE16
AE17
AE18
AE22
nRESET
nRST_PANEL
6
GPIO_A0_TX_EN3_TESTOUT8_GPIO_6
GPIO_A1_TX_EN4_TESTOUT9_GPIO_7
GPIO_A2_TX_C_TESTOUT10_GPIO_8
GPIO_A3_TX_D_TESTOUT11_GPIO_9
GPIO_A4_nTX_C_TESTOUT12_GPIO_10
GPIO_A5_nTX_D_TESTOUT13_GPIO_11
GPIO_A6_SAM_HOLD0_TESTOUT14_GPIO_12
GPIO_A7_SAM_HOLD1_TESTOUT15_GPIO_13
68
68
68
nRESET
nRSTOUT_GPO_0
CLKOUT_GPO_1
TESTMODE
OM0
OM1
OM2
OM3
R195
R196
R97
D9
E10
G1
AC5
AC6
AB6
AA6
AD6
5
SD_CKE
nSCS0
nSCS1
10K
DGND
F1
F2
J25
H25
F3
J24
4
A14
D14
E14
B14
nSELECTIN
nAUTOFD
nINIT
nSTROBE
AF11
AF14
AF17
AF7
AF21
CKE
nSCS0
nSCS1
nSCS2
nSCS3_GPO_13
nSCS4_GPO_14
SDCLK_FBK
SDCLK0
SDCLK1
EINT0
EINT1
EINT2_GPI_19
EINT3_GPI_20
EINT4_GPI_21
EINT5_GPI_22
SA(0:12)
DQM0
DQM1
DQM2
DQM3
B15
E16
D16
C16
B16
A16
D17
C17
AC15
AC16
68
68
BA0
BA1
AB17
AC18
PPD0_TESTOUT0
PPD1_TESTOUT1
PPD2__TESTOUT2
PPD3_TESTOUT3
PPD4_TESTOUT4
PPD5_TESTOUT5
PPD6_TESTOUT6
PPD7_TESTOUT7
68
68
R76
R81
DQM0
DQM1
DQM2
DQM3
AD15
AD16
AD17
AD18
RA26
33
nWE
AC17
RA29
33
C14
A17
D15
E15
C15
A18
B1
D3
E1
F4
D1
D2
E2
E3
F5
G5
C2
E4
G6
F6
E5
C3
D4
C1
OP_Y_LED
OP_M_LED
OP_C_LED
OP_K_LED
7
OP_STA_LED1
OP_STA_LED2
OP_MODE_LED
nOP_KEY_MODE
nOP_KEY_ONLINE
E13
C12
D12
AE25
AE26
C9
B9
E12
AD24
AF26
AA21
AD22
AF1
AF2
AF3
AE1
AE2
AE3
AF4
AC23
AE24
AF25
AF24
AC22
AD23
AE23
AF23
R17
10K
DGND
MAC_MDC
MAC_MDIO
MAC_COL
MAC_TX_CLK
MAC_TXD0
MAC_TXD1
MAC_TXD2
MAC_TXD3
MAC_TX_EN
MAC_LED_CON
MAC_RX_ERR
MAC_CRS
MAC_RX_CLK
MAC_RXD0
MAC_RXD1
MAC_RXD2
MAC_RXD3
MAC_RX_DV
DEBUG_TXD
PANEL_TXD
SCF_TXD
SCF_CLK
DEBUG_RXD
PANEL_RXD
SCF_RXD
nSCF_RDY
SCL
SDA
NF_CLE
NF_ALE
NF_nCE
NF_nRE
NF_nWE
NF_RnB
+3.3V
R72
10K
10
U1-5
74LCX14
TITLE:
8
U1-4
74LCX14
8
+3.3V
R3
220K
C10
100nF
9
DGND
Digtal Printing Division
R&D 5
8
CHORUSm(1)
Size
A3
2/15
CLP-300(N)/CLX-3160N(FN)
Main_V0.11
11
CLX-3160N(FN) Only
FLAT_MOT_PLS
nFLAT_MOT_EN
nFLAT_MOT_SLEEP
FLAT_MOT_DIR
FLAT_MOT_MS1
FLAT_MOT_MS2
LSU_SH1
LSU_SH2
NR3 0
Engineer K.C.LEE
R&D CHK S.D.AN
Drawn by
DOC CTRL CHK
MFG ENGR CHK
7
This Document can not be used without Samsung’s authorization.
3
RA33
33
SDCLK0
SDCLK1
SDCLK2
SDCLK3_GPO_11
SDCLK4_GPO_12
RA12
ADDR(1)
33
ADDR(2)
ADDR(3)
ADDR(4)
ADDR(5)
ADDR(6)
ADDR(7)
ADDR(8)
ADDR(9)
ADDR(10)
ADDR(11)
ADDR(12)
ADDR(13)
ADDR(14)
ADDR(15)
ADDR(16)
ADDR(17)
ADDR(18)
ADDR(19)
ADDR(20)
ADDR(21)
ADDR(22)
ADDR(23)
nSDRAM_WR
BA0
BA1
RA10
33
RA24
33
P1
P2
N1
N2
N3
N4
N5
M1
M2
M3
M4
L2
L3
L4
L5
K1
K2
K3
K4
J1
J2
J3
J4
RA30
33
RA9
33
RA25
33
R66
RA15
10K
RA22
33
nINT_USB_DEVICE
nINT_WNIC
nINT_MODEM
nINT_USB_HOST
nITB_HOME
+3.3V
RA34
10K
SD(0:31)
2
RA21
33
D
E
F
1
Service Manual
RA23
33
nRAS
nCAS
R193
R194
nRAS
nCAS
RA20
33
ADDR1
ADDR2
ADDR3
ADDR4
ADDR5
ADDR6
ADDR7
ADDR8
ADDR9
ADDR10
ADDR11
ADDR12
ADDR13
ADDR14
ADDR15
ADDR16
ADDR17
ADDR18
ADDR19
ADDR20_CfgAdvFlash
ADDR21_CfgBusWidth
ADDR22_CfgAddCycle
ADDR23_CfgPageSize
RA8
33
SD0
SD1
SD2
SD3
SD4
SD5
SD6
SD7
SD8
SD9
SD10
SD11
SD12
SD13
SD14
SD15
SD16
SD17
SD18
SD19
SD20
SD21
SD22
SD23
SD24
SD25
SD26
SD27
SD28
SD29
SD30
SD31
AE6
AE7
AD7
AC7
AB7
AA7
AF8
AE8
AD8
AC8
AE9
AD9
AC9
AB9
AE10
AD10
AC10
AE11
AD11
AC11
AB11
AF12
AE12
AD12
AC12
AE13
AD13
AC13
AB13
AE14
AD14
AC14
RA19
33
SA0
SA1
SA2
SA3
SA4
SA5
SA6
SA7
SA8
SA9
SA10
SA11
SA12
AE19
AD19
AC19
AB19
AF20
AE20
AD20
AC20
AB20
AE21
AD21
AC21
AB21
RA32
33
RA7
33
DATA(0)
DATA(1)
DATA(2)
DATA(3)
DATA(4)
DATA(5)
DATA(6)
DATA(7)
DATA(8)
DATA(9)
DATA(10)
DATA(11)
DATA(12)
DATA(13)
DATA(14)
DATA(15)
DATA(16)
DATA(17)
DATA(18)
DATA(19)
DATA(20)
DATA(21)
DATA(22)
DATA(23)
DATA(24)
DATA(25)
DATA(26)
DATA(27)
DATA(28)
DATA(29)
DATA(30)
DATA(31)
AD1
AD2
AD3
AC1
AC2
AC3
AC4
AB1
AB2
AB3
AB4
AB5
AA1
AA2
AA3
AA4
AA5
Y1
Y2
Y3
Y4
Y5
W1
W2
W3
W4
W5
V2
V3
V4
U1
U2
DATA0_NFCON_IO_0
DATA1_NFCON_IO_1
DATA2_NFCON_IO_2
DATA3_NFCON_IO_3
DATA4_NFCON_IO_4
DATA5_NFCON_IO_5
DATA6_NFCON_IO_6
DATA7_NFCON_IO_7
DATA8_NFCON_IO_8
DATA9_NFCON_IO_9
DATA10_NFCON_IO_10
DATA11_NFCON_IO_11
DATA12_NFCON_IO_12
DATA13_NFCON_IO_13
DATA14_NFCON_IO_14
DATA15_NFCON_IO_15
DATA16
DATA17
DATA18
DATA19
DATA20
DATA21
DATA22
DATA23
DATA24
DATA25
DATA26
DATA27
DATA28
DATA29
DATA30
DATA31
SA(0)
SA(1)
SA(2)
SA(3)
SA(4)
SA(5)
SA(6)
SA(7)
SA(8)
SA(9)
SA(10)
SA(11)
SA(12)
RA18
33
SD(0)
SD(1)
SD(2)
SD(3)
SD(4)
SD(5)
SD(6)
SD(7)
SD(8)
SD(9)
SD(10)
SD(11)
SD(12)
SD(13)
SD(14)
SD(15)
SD(16)
SD(17)
SD(18)
SD(19)
SD(20)
SD(21)
SD(22)
SD(23)
SD(24)
SD(25)
SD(26)
SD(27)
SD(28)
SD(29)
SD(30)
SD(31)
5.1K
R15
A
B
C
D
E
F
Samsung Electronics
4
100nF
U10-2
5
+3.3V
5
6
FOR FUTURE MODEL
6
0
VSB
NR5
0
Vb
7
NR113
3
100nF
C221
2
100nF
C227
1
100nF
C254
+1.2V
100nF
C219
A
+1.2V
C267
DGND
100nF
AFE_SLOAD
nHSYNC1
nBLDC_MOTOR_EN
BLDC_MOTOR_READY
LSU_MOT_CLK
100nF
C222
nLSU_READY
VDO1_plus
VDO1_minus
VDO2_plus
VDO2_minus
VDO1_GPO_15
VDO2_GPO_16
nHSYNC1_GPIO1_0
nHSYNC2_GPIO1_1
nFSYNC_GPI_6
LSUCLK_cCLK
nPRINT_nCMSG
nLREADY_nEMSG
VDO1_Plus
VDO1_Minus
VDO2_Plus
VDO2_Minus
PHIALVDS
nHSYNC1_Plus
nHSYNC1_Minus
nHSYNC2_Plus
nHSYNC2_Minus
LSYNC1_MOD_GPIO1_2
LSYNC2_MOD_GPIO1_3
VDO_OUT1_MOD_GPIO1_4
VDO_OUT2_MOD_GPIO1_5
VLCK_MOD_GPIO1_6
100nF
C135
nFUSER_EN
nLD_EN
nLSU_MOTOR_EN
PICKUP_CLUTCH
REGI_CLUTCH
C70
PD1_MOD0_GPIO1_7
PD1_MOD1_GPIO1_8
PD1_MOD2_GPIO1_9
PD1_MOD3_GPIO1_10
PD1_MOD4_GPIO1_11
PD1_MOD5_GPIO1_12
PD1_MOD6_GPIO1_13
PD1_MOD7_GPIO1_14
PD1_MOD8_GPIO1_15
PD1_MOD9_GPIO1_16
PD1_MOD10_GPIO1_17
PD1_MOD11_GPIO1_18
100nF
C125
A26
D24
C25
B26
C26
D25
E22
E23
E24
E25
D26
E26
100nF
C215
FAN_MAIN
PTL
nTHV_EN
DEV_CLUTCH
ERASE_LAMP
ITB_CLUTCH
THV_CLUTCH
nDEV_EN
DEV_SOL1
DEV_SOL2
DEV_SOL3
DEV_SOL4
100nF
C101
B
100nF
100uF
16V
3.3K
100nF
C124
R89
100nF
C126
DGND
100nF
C189
A25
B24
C22
D22
D18
C24
D20
B18
A19
B19
A20
B20
D19
A21
B21
A22
B22
E18
D23
C20
C23
C18
100nF
C164
PD2_MOD0_CLK_LINE_GPIO1_19
PD2_MOD1_CLK_PIX_IWIN_GPIO1_20
PD2_MOD2_OUT_CLK_LINE_GPIO1_21
PD2_MOD3_OUT_CLK_PIX_GPIO1_22
PD2_MOD4_OUT_IWIN_GPIO1_23
PD2_MOD5_OUT_BIN_GPIO1_24
PD2_MOD6_AFE_D10_GPIO1_25
PD2_MOD7_AFE_D10_GPIO1_26
PD2_MOD8_AFE_D12_GPIO1_27
PD2_MOD9_AFE_D13_GPIO1_28
PD2_MOD10_AFE_D14_GPIO1_29
PD2_MOD11_AFE_D15_GPIO1_30
100nF
C158
C
100nF
C181
F22
F23
F24
F25
F26
G21
G22
G23
G24
G25
H23
H24
C182
D
100nF
C136
nP_EMPTY
nP_EXIT
nREGI_SENS
nCOVER_OPEN
nDEV_HOME
WASTE_EMPTY
SCANNER_BW_CONTROL
nFLAT_COVER_OPEN
nSCANNER_HOME
nADF_MODULE_DETECT
WASTE_LED
nBIN_FULL
100nF
100nF
C148
GND_A
GND_PLL_1
GND_PLL_2
GND_RING_1
GND_RING_2
C188
100nF
C187
B6
B10
D11
B23
F20
100nF
100nF
C159
DGND
100nF
C110
100nF
C149
GND_1
GND_2
GND_3
GND_4
GND_5
GND_6
GND_7
GND_8
GND_9
GND_10
100nF
C104
100nF
C197
A1
A11
A24
B17
E20
G26
H1
K10
K11
K12
100nF
C114
100nF
C131
+3.3V
100nF
C118
100nF
C134
DGND
100nF
E
F
C174
4
100nF
3
C228
100nF
C179
2
100nF
100nF
C61
1
100nF
100nF
100nF
C163
AFE_D0
AFE_D1
AFE_D2
AFE_D3
AFE_D4
AFE_D5
AFE_D6
AFE_D7
AFE_D8
AFE_D9
SRAM_A0
SRAM_A1
SRAM_A2
SRAM_A3
SRAM_A4
SRAM_A5
SRAM_A6
SRAM_A7
SRAM_A8
SRAM_A9
SRAM_A10
SRAM_A11
SRAM_A12
SRAM_A13
SRAM_A14
SRAM_A15
SRAM_D0_GPIO_0
SRAM_D1_GPIO_1
SRAM_D2_GPIO_2
SRAM_D3_GPIO_3
SRAM_D4_GPIO_4
SRAM_D5_GPIO_5
SRAM_D6_GPIO_6
SRAM_D7_GPIO_7
SRAM_D8_GPIO_8
SRAM_D9_GPIO_9
SRAM_D10_GPIO_10
SRAM_D11_GPIO_11
SRAM_D12_GPIO_12
SRAM_D13_GPIO_13
SRAM_D14_GPIO_14
SRAM_D15_GPIO_15
SRAM_nWR
PItg1
PI1
PI2
PIrs
PIcp
ADC_CLK
CDS2_CLK
LEVEL_SHIFT_GPIO_17
Plsh_GPIO_18
Pltg3_GPIO_19
BLED_GPIO_20
GLED_GPIO_21
RLED_GPIO_22
Pltg2_GPIO_23
TX_EN1
TX_EN2
TX_A
TX_B
nTX_A
nTX_B
MOTOR_POL
AFE_D(0)
AFE_D(1)
AFE_D(2)
AFE_D(3)
AFE_D(4)
AFE_D(5)
AFE_D(6)
AFE_D(7)
+3.3V
SRAM_A(0)
SRAM_A(1)
SRAM_A(2)
SRAM_A(3)
SRAM_A(4)
SRAM_A(5)
SRAM_A(6)
SRAM_A(7)
SRAM_A(8)
SRAM_A(9)
SRAM_A(10)
SRAM_A(11)
SRAM_A(12)
SRAM_A(13)
SRAM_A(14)
SRAM_A(15)
SRAM_D(0)
SRAM_D(1)
SRAM_D(2)
SRAM_D(3)
SRAM_D(4)
SRAM_D(5)
SRAM_D(6)
SRAM_D(7)
SRAM_D(8)
SRAM_D(9)
SRAM_D(10)
SRAM_D(11)
SRAM_D(12)
SRAM_D(13)
SRAM_D(14)
SRAM_D(15)
R107
10K
AFE_D(0:7)
SRAM_A(0:15)
VSB
8
R&D 5
1
2
A
B
C
D
E
F
Service Manual
3/15
CLP-300(N)/CLX-3160N(FN)
Main_V0.11
8
CHORUSm(2)
Size
A3
BAT1
CR-2032T6
D23
RB420D T147
D22
MMSD914T1
+3.3V
RTC
DGND
R112
200
C226
10uF
16V
2402-001049
SRAM_D(0:15)
TEST_LED3
AFE_SCLK
nADF_MOT_PHA
nADF_MOT_PHB
nADF_MOT_A
nADF_MOT_B
nADF_MOT_NB
nADF_MOT_NA
TITLE:
Digtal Printing Division
nSRAM_WR
SCANNER_PI_TG1
SCANNER_PI1
SCANNER_PI2
SCANNER_PI_RS
SCANNER_PI_CP
AFE_ADC_CLK
AFE_CDS2_CLK
SCANNER_DPI_CONTROL
SCANNER_PI_SH
AFE_SDATA
FOR CLX-3160FN MODEL
J23
J22
K26
K25
K24
K23
L25
L24
L23
L22
AB22
AD26
AD25
AC26
AC25
AC24
AB25
AB24
AB23
AA22
AA23
AA24
AA25
Y21
Y22
Y23
Y24
Y25
W23
W24
W25
V22
V23
V24
V25
U22
U23
U24
U25
U26
T23
T24
T25
P25
AA26
W26
T26
P26
L26
H26
R22
R23
R24
R25
P22
P23
P24
N24
N23
N25
M22
M23
M24
M25
Engineer K.C.LEE
Drawn by
R&D CHK S.D.AN
DOC CTRL CHK
MFG ENGR CH K
7
This Document can not be used without Samsung’s authorization.
C204
C180
C173
100nF
C170
Samsung Electronics
100nF
C286
C6
C13
PWM_MHV
PWM_THV
PWM_DEV_DC
PWM_DEV_AC
PWM_DEV_VPP
PWM_ITHV
PWM_CCD_LAMP
PWM_MOT
KEYCLICK
GND_11
GND_12
GND_13
GND_14
GND_15
GND_16
GND_17
GND_18
GND_19
GND_20
GND_21
GND_22
GND_23
GND_24
GND_25
GND_26
GND_27
GND_28
GND_29
GND_30
GND_31
GND_32
GND_33
GND_34
GND_35
GND_36
GND_37
GND_38
GND_39
GND_40
GND_41
GND_42
GND_43
GND_44
GND_45
GND_46
GND_47
GND_48
GND_49
GND_50
GND_51
GND_52
GND_53
GND_54
GND_55
GND_56
GND_57
GND_58
GND_59
GND_60
GND_61
GND_62
GND_63
GND_64
GND_65
GND_66
GND_67
GND_68
GND_69
GND_70
GND_71
GND_72
GND_73
GND_74
GND_75
GND_76
GND_77
GND_78
GND_79
GND_80
GND_81
GND_82
100nF
C214
K13
K14
K15
K16
K17
L10
L11
L12
L13
L14
L15
L16
L17
M10
M11
M12
M13
M14
M15
M16
M17
N10
N11
N12
N13
N14
N15
N16
N17
N26
P10
P11
P12
P13
P14
P15
P16
P17
R10
R11
R12
R13
R14
R15
R16
R17
R26
T1
T10
T11
T12
T13
T14
T15
T16
T17
U10
U11
U12
U13
U14
U15
U16
U17
V26
AB26
AF6
AF10
AF13
AF15
AF18
AF22
C218
A3.3_VDD
RTC3.0_VDD
C19
C21
D21
E19
LVDS3.3_VDD1
LVDS3.3_VDD2
LVDS3.3_VDD3
LVDS3.3_VDD4
A15
B25
E17
K5
K22
L1
M26
P5
T22
V1
V5
Y26
AA20
AB8
AB12
AB16
AF9
AF19
3.3VDD_1
3.3VDD_2
3.3VDD_3
3.3VDD_4
3.3VDD_5
3.3VDD_6
3.3VDD_7
3.3VDD_8
3.3VDD_9
3.3VDD_10
3.3VDD_11
3.3VDD_12
3.3VDD_13
3.3VDD_14
3.3VDD_15
3.3VDD_16
3.3VDD_17
3.3VDD_18
B11
E11
A23
E21
1.2VDD_PLL_1
1.2VDD_PLL_2
1.2VDD_RING_1
1.2VDD_RING_2
A8
B2
D13
E6
F21
H22
J26
M5
N22
W22
Y6
AB10
AB14
AB18
1.2VDD_1
1.2VDD_2
1.2VDD_3
1.2VDD_4
1.2VDD_5
1.2VDD_6
1.2VDD_7
1.2VDD_8
1.2VDD_9
1.2VDD_10
1.2VDD_11
1.2VDD_12
1.2VDD_13
1.2VDD_14
MHV_READ
THV_READ
ITHV_READ
WASTE_LEVEL
FUSER_THERM1
FUSER_THERM2
INNER_TEMP
OUT_TEMP
LD_POWER1
FLAT_MOT_DAC
A5
B5
A4
C5
B4
A3
D5
C4
A6
D6
B3
D7
F7
E7
A7
B7
C7
C8
D8
E8
E9
B8
A2
AIN0
AIN1
AIN2
AIN3
AIN4
AIN5
AIN6
AIN7
DAC1_OUT
DAC2_OUT
MOT_A_nCBSY
MOT_nA_nEBSY
MOT_B_nEPRDY
MOT_nB_GPO_26
PWM_OUT0
PWM_OUT1
PWM_OUT2
PWM_OUT3
PWM_OUT4_GPO_27
PWM_OUT5_GPO_28
PWM_OUT6_GPO_29
PWM_OUT7_GPO_30
TONE_OUT_GPO_31
C62
A
B
C
D
E
F
B
1
1
1
R190
0
NR114
0
1
2
3
4
DGND
OSC5
2
C210
15pF
XOUT
FRSEL
0.5%
0.4%
0%
0
N.C
1
LOW
N.C
S0
0
0
0
N.C
N.C
S1
5
6
7
8
ATS-49/U,12MHz,50ppm
U12
XIN/CLKIN
SSCLK
VDD
S1
VSS
S0
1.1%
CY25811
1.3%
U25
Vout 1
+3.3V
R172
100
DGND
C178
15pF
DGND
DGND
C302
1nF
R170
1K
2
3
1
33
2
F1
STS104B
3
C194
100nF
R88
nRESET
3
+3.3V
C312
22pF
DGND
2
3
Q11
KSC1623-Y
XI_MCLK
+5V
R142 300
1
3
1
CLX-3160FN ONLY
1
R151
470K
R152 5.6K
C129
4
15pF
5
[ VCLK ]
Vb
C244
10uF
0
XI_VCLK
XO_VCLK
U19
ATS-49/U,12MHz,50ppm
15pF
OSC2
C128
DGND
F2
STS104B
3
2
R115
10
Q9
KSB1151-Y
R121
+3.3V
C234
100nF
DGND
1
2
56
R161
56
D27
RB420D T147
R162
Q12
KSA1182-Y
+5V
2
3
4
7 PVIN
8 SVIN
10 SHDN
4 SGND
12
SW 6
SFB 5
11
VSET
PSET
MVPG31
C308
47uF
16V
DGND
VBIN
5
C165
22pF
22pF
OSC3
2.2uH
C155
DGND
L9
R105 31.6K,1%
R109 280K,1%
6
XI_RTC
MC-306,32.768KHz
XO_RTC
[ RTC ]
+1.2V
C243
22uF
6
+5V
1
DGND
7
R175
8
LED1
5.1K
SLS-NNGA102TS
+3.3V
C255
100uF
16V
+3.3V
Digtal Printing Division
R&D 5
8
Clock & Power On Reset
Size
A3
A
B
C
D
E
F
Samsung Electronics
4/15
CLP-300(N)/CLX-3160N(FN)
Main_V0.11
TITLE:
1
U24
LD1117DT33C
3 IN OUT 2
GND
C303 C301
10uF 100nF
16V
TEST_LED3
F3
STS104B
3
2
DGND
L8
L5
FGND
3301-000325|R3225_BEAD
Engineer K.C.LEE
DOC CTRL CHK
R&D CHK S.D.AN
Drawn by
MFG ENGR CHK
7
This Document can not be used without Samsung’s authorization.
DGND
NR6 30K
[ SYSTEM CLOCK ]
Vin
Vss 2
XC61FN3112MR
3
+3.3V
C211
DGND 15pF
R189
0
+3.3V
C277
100nF
DGND
B
[ SYSTEM RESET ]
Service Manual
NC3 3
PGND
13
NC1 1
NC2 2
NC4
9
A
B
C
D
E
F
1
1
Samsung Electronics
2
nCS_BOOT
nRD
nWR
2
ADDR(22:2)
nRESET
ADDR(21)
ADDR(20)
ADDR(19)
ADDR(18)
ADDR(17)
ADDR(16)
ADDR(15)
ADDR(14)
ADDR(13)
ADDR(12)
ADDR(11)
ADDR(10)
ADDR(9)
ADDR(8)
ADDR(7)
ADDR(6)
ADDR(5)
ADDR(4)
ADDR(3)
ADDR(2)
9
16
17
48
1
2
3
4
5
6
7
8
18
19
20
21
22
23
24
25
U9
ADDR(22)
R197
33
26
28
11
10
13
14
9
16
17
48
1
2
3
4
5
6
7
8
18
19
20
21
22
23
24
25
U13
A19
A18
A17
A16
A15
A14
A13
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
NC2
NC3
NC4
3
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
VCC
_BYTE
45
43
41
39
36
34
32
30
44
42
40
38
35
33
31
29
37
47
46
VSS1
27
VSS2
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
VCC
45
43
41
39
36
34
32
30
44
42
40
38
35
33
31
29
37
47
46
VSS1
27
VSS2
_BYTE
AM29LV160D
_CE
15
_OE _BUSY
12
_WE _RESET
NC2
NC3
NC4
A19
A18
A17
A16
A15
A14
A13
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
AM29LV160D
1107-001286
26
_CE
28
15
_OE
_BUSY
11
12
_WE _RESET
10
13
14
ADDR(21)
ADDR(20)
ADDR(19)
ADDR(18)
ADDR(17)
ADDR(16)
ADDR(15)
ADDR(14)
ADDR(13)
ADDR(12)
ADDR(11)
ADDR(10)
ADDR(9)
ADDR(8)
ADDR(7)
ADDR(6)
ADDR(5)
ADDR(4)
ADDR(3)
ADDR(2)
ADDR(22)
D39
MMSD914T1
3
R201
100K
4
DATA(15)
DATA(14)
DATA(13)
DATA(12)
DATA(11)
DATA(10)
DATA(9)
DATA(8)
DATA(7)
DATA(6)
DATA(5)
DATA(4)
DATA(3)
DATA(2)
DATA(1)
DATA(0)
R86
10K
DATA(31)
DATA(30)
DATA(29)
DATA(28)
DATA(27)
DATA(26)
DATA(25)
DATA(24)
DATA(23)
DATA(22)
DATA(21)
DATA(20)
DATA(19)
DATA(18)
DATA(17)
DATA(16)
R106
10K
DGND
DATA(31:0)
DGND
C146
100nF
+3.3V
+3.3V
C202
100nF
DGND
4
5
NF_RnB
NF_nRE
NF_nCE
NF_CLE
NF_ALE
NF_nWE
NF_nWP
5
R96 R95
5.1K 1K
6
100nF
C116
+3.3V
C212
DGND
100nF
C195
100pF
DGND
12
37
1
2
3
4
5
6
10
11
14
7
8
9
16
17
18
19
15
20
21
22
23
24
VCC1
VCC2
NC1
NC2
NC3
NC4
NC5
NC6
NC7
NC8
NC9
R|B*
RE|
CE|
CLE
ALE
WE|
WP|
NC10
NC11
NC12
NC13
NC14
NC15
7
Model
CLP-300
DGND
DATA(0)
DATA(1)
DATA(2)
DATA(3)
DATA(4)
DATA(5)
DATA(6)
DATA(7)
DATA(8)
DATA(9)
DATA(10)
DATA(11)
DATA(12)
DATA(13)
DATA(14)
DATA(15)
+3.3V
Engineer K.C.LEE
R &D CHK S.D.AN
Drawn by
DOC CTRL CHK
MFG ENGR CHK
7
8
8
Flash Memory
Size
A3
5/15
CLP-300(N)/CLX-3160N(FN)
Main_V0.11
R&D 5
Digtal Printing Division
4MB
4MB
2MB
Configuration Size
8Mbit * 2
(1107-001302)
TITLE:
DATA(0:15)
16Mbit * 2
CLP-300N
(1107-001286)
CLX-3160N 16Mbit * 2
CLX-3160FN (1107-001286)
26
28
30
32
40
42
44
46
27
29
31
33
41
43
45
47
39
36
35
34
38
13
25
48
FOR FUTURE PDL
NU1
IO0
IO1
IO2
IO3
IO4
IO5
IO6
IO7
IO8
IO9
IO10
IO11
IO12
IO13
IO14
IO15
NC19
NC18
NC17
NC16
LOCKPRE
VSS3
VSS2
VSS1
K9F5616U0C
RA14
10K
DGND
[ NAND SETTING ]
ADDR(22)
ADDR(21)
ADDR(20)
ADDR(23)
6
This Document can not be used without Samsung’s authorization.
A
B
C
D
E
F
Service Manual
2
3
C100
100nF
C191
100nF
C88
100nF
C175
100nF
C94
100nF
4
U6
DQ15
DQ14
DQ13
DQ12
DQ11
DQ10
DQ9
DQ8
DQ7
DQ6
DQ5
DQ4
DQ3
DQ2
DQ1
DQ0
SD(31)
SD(30)
SD(29)
SD(28)
SD(27)
SD(26)
SD(25)
SD(24)
SD(23)
SD(22)
SD(21)
SD(20)
SD(19)
SD(18)
SD(17)
SD(16)
6
53
51
50
48
47
45
44
42
13
11
10
8
7
5
4
2
Vb
100nF
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
C147
NC/RFU
100nF
DGND
+3.3V
DGND
100nF
C162
36
35
22
34
33
32
31
30
29
26
25
24
23
1
14
27
3
9
43
49
SD(31)
SD(30)
SD(29)
SD(28)
SD(27)
SD(26)
SD(25)
SD(24)
SD(23)
SD(22)
SD(21)
SD(20)
SD(19)
SD(18)
SD(17)
SD(16)
28
41
54
6
12
46
52
53
51
50
48
47
45
44
42
13
11
10
8
7
5
4
2
C82
40
18
*RAS
17
*CAS
VDD1
VDD2
VDD3
VDDQ1
VDDQ2
VDDQ3
VDDQ4
VSS1
VSS2
VSS3
VSSQ1
VSSQ2
VSSQ3
VSSQ4
DQ15
DQ14
DQ13
DQ12
DQ11
DQ10
DQ9
DQ8
DQ7
DQ6
DQ5
DQ4
DQ3
DQ2
DQ1
DQ0
K4S561632B-TC1L
U15
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
NC/RFU
100nF
5
SA(12)
SA(11)
SA(10)
SA(9)
SA(8)
SA(7)
SA(6)
SA(5)
SA(4)
SA(3)
SA(2)
SA(1)
SA(0)
nRAS
nCAS
40
36
35
22
34
33
32
31
30
29
26
25
24
23
38
CLK
37
CKE
15
LDQM
39
UDQM
19
*CS
16
*WE
20
BA0
21
BA1
SDCLK0
SD_CKE
DQM2
DQM3
nSCS0
nSDRAM_WR
BA0
BA1
R64 0
SA(12)
SA(11)
SA(10)
SA(9)
SA(8)
SA(7)
SA(6)
SA(5)
SA(4)
SA(3)
SA(2)
SA(1)
SA(0)
1
14
27
3
9
43
49
28
41
54
6
12
46
52
100nF
C176
1
100nF
SA(0:12)
SD(15)
SD(14)
SD(13)
SD(12)
SD(11)
SD(10)
SD(9)
SD(8)
SD(7)
SD(6)
SD(5)
SD(4)
SD(3)
SD(2)
SD(1)
SD(0)
100nF
C216
+3.3V
18
*RAS
17
*CAS
VDD1
VDD2
VDD3
VDDQ1
VDDQ2
VDDQ3
VDDQ4
VSS1
VSS2
VSS3
VSSQ1
VSSQ2
VSSQ3
VSSQ4
C87
Vb
53
51
50
48
47
45
44
42
13
11
10
8
7
5
4
2
C83
U7
1105-001384
DQ15
DQ14
DQ13
DQ12
DQ11
DQ10
DQ9
DQ8
DQ7
DQ6
DQ5
DQ4
DQ3
DQ2
DQ1
DQ0
nRAS
nCAS
38
CLK
37
CKE
15
LDQM
39
UDQM
19
*CS
16
*WE
20
BA0
21
BA1
R100 0
BA0
BA1
DQM2
DQM3
nSCS1
nSDRAM_WR
SDCLK1
SD_CKE
100nF
100nF
DQ15
DQ14
DQ13
DQ12
DQ11
DQ10
DQ9
DQ8
DQ7
DQ6
DQ5
DQ4
DQ3
DQ2
DQ1
DQ0
100nF
28
41
54
6
12
46
52
100nF
100nF
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
U16
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
A0
NC/RFU
VDD1
VDD2
VDD3
VDDQ1
VDDQ2
VDDQ3
VDDQ4
VSS1
VSS2
VSS3
VSSQ1
VSSQ2
VSSQ3
VSSQ4
K4S561632B-TC1L
6
100nF
C192
C207
NC/RFU
100nF
C183
DGND
5
100nF
C72
C99
36
35
22
34
33
32
31
30
29
26
25
24
23
1
14
27
3
9
43
49
C107
Configuration Size
8
Model
128Mbit * 2
32MB
(1105-001357)
7
CLP-300
TITLE:
Digtal Printing Division
R&D 5
6/15
CLP-300(N)/CLX-3160N(FN)
Main_V0.11
8
SDRAM
Size
A3
64MB
CLP-300N 256Mbit * 2
(1105-001384)
CLX-3160N 256Mbit * 4
128MB
CLX-3160FN (1105-001384)
Engineer K.C.LEE
DOC CTRL CHK
R&D CHK S.D.AN
Drawn by
MFG ENGR CHK
7
This Document can not be used without Samsung’s authorization.
4
C96
100nF
C106
40
18
*RAS
17
*CAS
VDD1
VDD2
VDD3
VDDQ1
VDDQ2
VDDQ3
VDDQ4
100nF
28
41
54
6
12
46
52
100nF
C206
DGND
SD(15)
SD(14)
SD(13)
SD(12)
SD(11)
SD(10)
SD(9)
SD(8)
SD(7)
SD(6)
SD(5)
SD(4)
SD(3)
SD(2)
SD(1)
SD(0)
100nF
C73
3
100nF
100nF
SD(0:31)
SA(12)
SA(11)
SA(10)
SA(9)
SA(8)
SA(7)
SA(6)
SA(5)
SA(4)
SA(3)
SA(2)
SA(1)
SA(0)
nRAS
nCAS
19
*CS
16
*WE
15
LDQM
39
UDQM
VSS1
VSS2
VSS3
VSSQ1
VSSQ2
VSSQ3
VSSQ4
53
51
50
48
47
45
44
42
13
11
10
8
7
5
4
2
C150
100nF
K4S561632B-TC1L
38
CLK
37
CKE
36
35
22
34
33
32
31
30
29
26
25
24
23
18
*RAS
17
*CAS
40
nRAS
nCAS
SDCLK0
SD_CKE
DQM0
DQM1
nSCS0
nSDRAM_WR
20
BA0
21
BA1
SA(12)
SA(11)
SA(10)
SA(9)
SA(8)
SA(7)
SA(6)
SA(5)
SA(4)
SA(3)
SA(2)
SA(1)
SA(0)
1
14
27
3
9
43
49
100nF
C200
K4S561632B-TC1L
38
CLK
37
CKE
15
LDQM
39
UDQM
19
*CS
16
*WE
20
BA0
21
BA1
SDCLK1
SD_CKE
DQM0
DQM1
nSCS1
nSDRAM_WR
BA0
BA1
R101 0
BA0
BA1
R65 0
2
C184
C201
C220
A
B
C
D
E
F
1
Service Manual
C161
A
B
C
D
E
F
Samsung Electronics
+3.3V
DGND
DGND
1
L10
1uH
LK16081ROK-T
15pF
C236
C235
15pF
+3.3V
C238
100nF
GND
2
USB_3.3VA
R25
100
C239
10uF
16V
2402-001049
USB_GND
C232
100nF
100
OSC6
ATS-49/U,12MHz,50ppm
R111
NC
2
4
3
VCC OUT
1
OSC1
SCO-10325AD-6M
ADDR(13)
ADDR(12)
ADDR(11)
ADDR(10)
ADDR(9)
ADDR(8)
ADDR(7)
ADDR(6)
ADDR(5)
ADDR(4)
ADDR(3)
3
+3.3V
C230
100nF
DGND
XI_USB
XO_USB
C229
100nF
DGND
C203
47uF
16V
USB_1V8
C224
100nF
U2
10nF
C231
C217
10nF
C198
C199
10nF
100nF
C213
10nF
VBUS 46
OSC2 64
+3.3V
R23
10K
NR4
10K
NOT USED
CLX-3160N(FN) Only
R36
10K
63 OSC1
60 CLKW
VBP 38
VREG_OUT 42
VREG_EN 41
DM1 34
DP1 33
ID 40
DM2 32
DP2 31
_PO 39
_OC 36
VDD2_5_10 10
VDD2_5_29 29
VDD2_5_53 53
VDDW_5 5
VDDW_21 21
VDDW_55 55
VDD3_3_35 35
AVDD3_3_43 43
AVDD3_3_45 45
AVDD2_5_62 62
47 _RESET
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
A12
A11
A10
A9
A8
A7
A6
A5
A4
A3
A2
A1
30 _CS
12 _WR
13 _RD
27
26
25
24
23
22
20
19
18
17
16
14
9
8
7
6
4
3
2
1
59
58
57
56
52
51
50
49
VSS15 15
VSS28 28
VSS54 54
AVSS44 44
AVSS61 61
DGND
DGND
DGND
R1
R6
R2
R7
10K
DGND
4
ADDR(9:2)
2
1
R98
+3.3V
ADDR(2)
ADDR(3)
ADDR(4)
ADDR(5)
ADDR(6)
ADDR(7)
ADDR(8)
ADDR(9)
1
5
10K
DGND
3 D1
3 D2
KDS226 KDS226
L1
C60
10uF
16V
2402-001049
2
+5V +3.3V
XI_USB
XO_USB
nINT_USB_DEVICE
nRD
nWR
nCS_USB_DEVICE
nRST_USB_DEVICE
nDREQ_USB_DEVICE
nDACK_USB_DEVICE
DGND
C59
10uF
16V
2402-001049
33
33
4.7K
C3
100nF
5
18
19
20
22
23
24
25
27
7
9
10
8
11
12
15
16
17
14
52
51
A0
A1
A2
A3
A4
A5
A6
A7
DREQ
DACK
7
U18
isp1582bs
DGND
6
WAKEUP
SUSPEND
RREF
VBUS
RPU
DP
DM
DATA0
DATA1
DATA2
DATA3
DATA4
DATA5
DATA6
DATA7
DATA8
DATA9
DATA10
DATA11
DATA12
DATA13
DATA14
DATA15
USB_3.3VA USB_1V8
+3.3V
6
RESET_N
EOT
DIOR
DIOW
nCS
nRD
nWR
INT
5
4
3
2
1
CN6-1
35303-0550
USB_GND
XTAL1
XTAL2
28
50
Vcc_1V8_28
Vcc_1V8_50
57
DGND_13
DGND_26
DGND_29
DGND_41
13
26
29
41
TGND
21
34
48
53
54
Vcc_I_O_21
Vcc_I_O_34
Vcc_I_O_48
Vcc_53
Vcc_54
AGND_1
AGND_5
1
5
A
B
C
DGND
15pF
NC2
ADDR(2)
+3.3V
11 _INT
37 _EXVBO
48 TEST
OTG242_LQFP64
0904-001865
4
P1
MINISMDC075-2
30
31
32
33
35
36
37
38
39
40
42
43
44
45
46
47
2
3
4
49
6
55
56
R110
10K
DATA(31:16)
2
1
1
D20
KDS226
2
3
DGND
8
CN14-1
787780-1
6
5
4
3
2
L7 INSTPAR 1
L6 INSTPAR
FGND
Digtal Printing Division
R&D 5
CLP-300(N)/CLX-3160N(FN)
Main_V0.11
8
Size
A3
A
B
C
D
E
F
Service Manual
USB Host & Device Controller 7/15
TITLE:
C190
1000NF
200K
3
D19
KDS226
+3.3V
R108
1.5K
R94
R93
1M
2402-001049
R102
12.1Kohm,1%
C205
10uF
16V
DATA(16)
DATA(17)
DATA(18)
DATA(19)
DATA(20)
DATA(21)
DATA(22)
DATA(23)
DATA(24)
DATA(25)
DATA(26)
DATA(27)
DATA(28)
DATA(29)
DATA(30)
DATA(31)
R114
10K
DGND
Engineer K.C.LEE
Drawn by
DOC CTRL CHK
R&D CHK S.D.AN
MFG ENGR CHK
7
This Document can not be used without Samsung’s authorization.
3
100nF
nRST_USB_HOST
DATA(31)
DATA(30)
DATA(29)
DATA(28)
DATA(27)
DATA(26)
DATA(25)
DATA(24)
DATA(23)
DATA(22)
DATA(21)
DATA(20)
DATA(19)
DATA(18)
DATA(17)
DATA(16)
R11 10K
R10 10K
DGND
2
C8
ADDR(2:13)
B
100nF
nCS_USB_HOST
nWR
nRD
DATA(31:16)
1
nINT_USB_HOST
1
100nF
100nF
C32
D
E
F
B
Samsung Electronics
100nF
C7
100nF
100nF
100nF
C58
C31
C22
100nF
10K
C57
R16
C45
C46
100nF
C6
A
1
LAN_LINK
R52
200
2
D9
MMSD914T1
D11
MMSD914T1
3
U8
4
RA36
10K
63mW
+3.3V
5
R68
100
+3.3V
D18 2
KDS226
3
1
2
DGND
1
1 D17 2 1
KDS226
3
D14
D16
KDS2263 KDS2263
DGND
2
+3.3V
CLP-300N & CLX-3160N(FN) Only
10K
DGND
DGND
10pF 10pF
LAN_LINK
5
6
6
C130 C119
C113
1
100nF
1K
100nF 100nF
R84
7
mf2
mf1
mf0
Pin
MF4 10/100 Mbps Speed Select
Scrambler Operation Disable
4B/5B Codeing Enable
Enable NRZ-NRZI conversion
Auto-Negotiation
Function
8
mf3
Multi-Function pins
mf4
Input Value
0
0
1
0
1
0
1
1
1
0
FDE
1
1
1
Advertise 100 HD
0
1
CFG1
Advertise 100 HD/FD
0
1
CFG0
Operating Configurations/ Auto-Negotiation Enabled
Desired
Configuration
Advertise 10 HD
1
Advertise All
Advertise 10 HD/FD
+3.3V
CN11
1 TDP
2 TCT
3 TDN
4 RDP
5 RCT
6 RDN
7 NC
8 CT_REF
9 FGND_9
10 FGND_10
11 LED1_ANODE
12 LED1_CATHOD
1605713-7
TITLE:
8
R&D 5
Ethernet Physical Layer
Size
A3
A
B
C
D
E
F
Samsung Electronics
8/15
CLP-300(N)/CLX-3160N(FN)
Main_V0.11
13 LED2_ANODE
14 LED2_CATHOD
FGND
Q8
MMBT2222ALT1
DGND
Engineer K.C.LEE
Drawn by
R&D CHK S.D.AN
DOC CTRL CHK
MFG ENGR CHK
7
Digtal Printing Division
Advertise 10/100 HD
2
3
R85
200
+3.3V
R55
LEDR10
LEDL
LEDC
LEDS
LEDTR
RA37
10K
63mW
49.9
C144 C153
49.9
R83
38
36
35
34
37
CG0 64
CG1 63
6
FDE
5
MF0
4
MF1
3
MF2
2
MF3
1
MF4
61
MDINT
29
RIP
RXN 18
19
RXP
DGND
R74
XI_PCLK
XO_PCLK
nRST_NIC
RA4
33
1/16W
RESET
12
X1
11 X2
28
60 CRS
59 COL
9
13
16
17
22
7
10
14
20
24
MAC_LED_CON
DGND
C71
TXN 23
21
TXP
VCCA1
VCCA2
VCCA3
VCCA4
VCCA5
GNDA1
GNDA2
GNDA3
GNDA4
GNDA5
VCCE_I1 39
VCCE_I2 45
62
VCCE_I3
GNDE_I1 25
40
GNDE_I2
GNDE_I3 50
NC3 30
8
NC4
100nF
58
TX3
57 TX2
56
TX1
55 TX0
52
TX_ER
RXD0
RXD1
RXD2
RXD3
54 TX_EN
53
TX_CLK
51 RX_ER
49 RX_CLK
48
RX_DV
47
46
44
43
42
MDC
41 MDIO
27
PWDDWN
26 TEST
33
TEST_SE
15 IREF
ste100p
100nF
C133
MAC_CRS
MAC_COL
MAC_TX_EN
C89
1nF
32 NC1
31 NC2
R73
5.1K
C157
RA5
C90
1nF
RA38
10K
63mW
XI_PCLK
100nF
33
1/16W
RA3
10K
63mW
100
(2804-004414)
R87
OSC4
XO_PCLK
100nF
C112
RA6
100
33
1/16W
R61
100
RA35
33
1/16W
R67
C102 C123
33pF 33pF
DGND
R177
1M
U1F25000-35D16N
4
C156
This Document can not be used without Samsung’s authorization.
3
100nF
100nF
MAC_TXD3
MAC_TXD2
MAC_TXD1
MAC_TXD0
MAC_RXD0
MAC_RXD1
MAC_RXD2
MAC_RXD3
MAC_RX_ERR
MAC_RX_DV
MAC_MDC
MAC_MDIO
MAC_RX_CLK
MAC_TX_CLK
C168
10pF
C167
10pF
DGND
2
10uF
16V
2402-001049
C139
C140
B
C
D
E
F
1
Service Manual
C111 100nF
AFE_D(0:7)
1
4
2
AFE_D(7)
AFE_D(6)
AFE_D(5)
AFE_D(4)
AFE_D(3)
AFE_D(2)
AFE_D(1)
AFE_D(0)
7
8
9
10
11
12
13
14
3
CIP40 ONLY USED
5
VDDDR
18
VDDA1
28
VDDA2
+3.3V
N R115
0
1
+5V
R191
0
4
HT82v26 ONLY USED
5
INV_POWER
FPC_24
CN3-1
CLX-3160N(FN) Only
100nF
+3.3V +5V +24V
C12
100nF
6
7
DGND
R38
4.7K
+3.3V
TITLE:
C27
100nF
+5V
8
+3.3V +24V
C311
100nF
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
50V
2203-005249
NC1
100nF
A
B
C
D
E
F
Service Manual
9/15
Size
A3
NOT USED
INV_POWER
C4
100nF
DGND
DGND
C50
100uF
50V
R&D 5
8
Scanner Interface
CLP-300(N)/CLX-3160N(FN)
Main_V0.11
L4
DR
D2
4
Q2
NDT2955
+24V
S 3
G 1
D1
2
D12
SS26
DGND
Engineer K.C.LEE
Drawn by
R&D CHK S.D.AN
DOC CTRL CHK
MFG ENGR CHK
7
CN1
DF11-24DP-2DSA(20)
U4
D7
D6
D5
D4
D3
D2
D1
D0
20
REFB
21
REFT
23
VCOM
25
OFFSET
C13
3
1nF
A
3
nADF_MOT_PHA
nADF_MOT_PHB
nADF_MOT_A
nADF_MOT_B
nADF_MOT_NA
nADF_MOT_NB
nADF_MODULE_DETECT
FLAT_MOT_PLS
nFLAT_MOT_EN
nFLAT_MOT_SLEEP
FLAT_MOT_DIR
FLAT_MOT_MS1
FLAT_MOT_MS2
FLAT_MOT_DAC
NOT USED
DGND
nADF_P_DET
nADF_P_REG
nADF_P_POS
nFLAT_COVER_OPEN
nBIN_FULL
1
1nF
C65
1
2
3
4
5
6
7
8
9
10
12
11
13
14
16
15
17
18
19
20
21
22
23
24
R34
4.7K
1nF
C39
15
C2
6
1nF
C26
22
B_VIN
24
G_VIN
26
R_VIN
C1 C54
U1-3
1nF
C52
CDS1_CLK
CDS2_CLK
ADCCLK
OEB
SCLK
SLOAD
C9
5
2203-005249|R1608_CAP
100nF 100nF100nF 100nF
DGND
R200
33
2
Q5
MMBT2222ALT1
1nF
C38
1
2
3
4
16
17
100pF
100nF
100pF
C17
C14
C92
100nF
C105
10uF 16V
C16
PWM_CCD_LAMP
C67
1000nF
C25
Digtal Printing Division
47K
R8
33
+3.3V
2
12
100pF
U1-2
74LCX14
SDATA
EN
DIN1
DIN2
VCC
GND
DIN3
DIN4
EN_
FIN1047M
C35
100nF
U1-1
74LCX14
14
7
C15
6
VSSDR
19
VSSA1
27
VSSA2
HT82V26
DGND
100nF
U1-6
6
1nF
33
100nF
C91
16
15
14
13
12
11
10
9
C69
U3
DGND
1
2
3
4
5
6
7
8
1000NF
DOUT1DOUT1+
DOUT2+
DOUT2DOUT3DOUT3+
DOUT4+
DOUT4-
100nF
C49
C48 15pF
DGND
R4
+3.3V
R29
10K
SRAM_D(0:15)
C55
13
100nF
C93
CIP40 : 0ohm USED
HT82V26 : 1K USED
HT82V26 USED
+3.3V
C248
100nF
100nF
DGND
5
100nF
C310
R46
R53
CIP40 NOT USED
DGND
SRAM_D(0)
SRAM_D(1)
SRAM_D(2)
SRAM_D(3)
SRAM_D(4)
SRAM_D(5)
SRAM_D(6)
SRAM_D(7)
SRAM_D(8)
SRAM_D(9)
SRAM_D(10)
SRAM_D(11)
SRAM_D(12)
SRAM_D(13)
SRAM_D(14)
SRAM_D(15)
C291
100nF
100nF
C42
SCANNER_PI_SH
AFE_CDS2_CLK
AFE_ADC_CLK
AFE_SCLK
AFE_SLOAD
AFE_SDATA
SCANNER_DPI_CONTROL
SCANNER_BW_CONTROL
SCANNER_PI_TG1
100
100
22
23
28
7
8
9
10
13
14
15
16
29
30
31
32
35
36
37
38
11
12
I_01
I_02
I_O3
I_O4
I_O5
I_O6
I_O7
I_O8
I_O9
I_O10
I_O11
I_O12
I_O13
I_O14
I_O15
I_O16
NC1
NC2
NC3
DGND
C80
4
R186
R184
1nF
100nF
C63
R46
1K
R53
2K
This Document can not be used without Samsung’s authorization.
3
1nF
1nF
47K
C41
1nF
R185
1nF
C84
C28
47K
C?
C66
1nF
47K
C78
R183
1nF
47K
C64
R182
1nF
1nF
R48
R49
U23
A0
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
VCC1
VSS1
34
33
100nF
C51
C53
100
100
1
2
3
4
5
18
19
20
21
24
25
26
27
42
43
44
VSS2
VCC2
C47
1nF
1nF
R50
R51
SRAM_A(0)
SRAM_A(1)
SRAM_A(2)
SRAM_A(3)
SRAM_A(4)
SRAM_A(5)
SRAM_A(6)
SRAM_A(7)
SRAM_A(8)
SRAM_A(9)
SRAM_A(10)
SRAM_A(11)
SRAM_A(12)
SRAM_A(13)
SRAM_A(14)
SRAM_A(15)
_CS
_WE
_LB
_UB
_OE
K6R1016V1D
15pF
SCANNER_PI_RS
SCANNER_PI1
SCANNER_PI2
SCANNER_PI_CP
SRAM_A(0:15)
nSRAM_WR
6
17
39
40
41
DGND
2
15pF
C77
B
C
D
E
F
1
15pF
C23 15pF
Samsung Electronics
C76
C37
C40
R43
10K
15pF
C75
C24
NC3
100nF 50V
C74
C36 15pF
A
B
C
1
+5V
FOR DEBUG
+3.3V
CN27-1
35303-0450
1
2
3
4
2
R92
R91
3
I2C Address Configuration
0
A2
0
0
A1
1
0
A0
Deve M
Deve Y
I2C Address
OPC
0
Not Used
Deve C
0
NPC & NVRAM
Deve K
1
Not Used
0
0
0
1
0
1
1
1
1
1
1
1
0
1
U11_A-1
WSDIF-8T
8
7
6
5
1
0
1
2
3
4
U11
8
7
6
5
C172
100nF
4
+3.3V
R80
1K
15pF
C137
R79
1K
15pF
SCL
SDA
5
CN12-1
35303-0750
1
2
3
4
5
6
7
2
1
+5V
6
C132
100nF
DGND
DISPLAY_PANEL
+5V
CN13-1
DF11-14DP-2DSA
3
B600
B600
B600
1nF 1nF
100
7
1nF
R&D CHK S.D.AN
Drawn by
DOC CTRL CHK
R82
10K
TITLE:
8
PANEL_RXD
nRST_PANEL
PANEL_TXD
nSCANNER_HOME
VBIN
OP_Y_LED
OP_M_LED
OP_C_LED
OP_K_LED
OP_STA_LED1
OP_STA_LED2
OP_MODE_LED
nOP_KEY_MODE
nOP_KEY_ONLINE
Digtal Printing Division
R&D 5
Size
A3
CLP-300(N)/CLX-3160N(FN)
Main_V0.11
8
Hyper Terminal, EEPROM, OPE 10/15
MFG ENGR CHK
7
1nF
C120 C108 C152 C141
R71
47K
+3.3V
OPE2 : CLX-3160N(FN) Only
NL2
NL3
NL1
3301-001122
DGND
OPE1 : CLP-300(N) Only
100
100
R75
R78
4
5
100
100
100
100
R59
100
R63
R60
R69
7
8
9
10
R62
100
1 D15
KDS226
DGND
R56
6
+3.3V
2
3
R57
1nF
C138
2 1
3
D13
KDS226
R192
47K
VBIN
1nF
C103
11
C151
100nF
C117
12
13
14
DGND
1nF
Engineer K.C.LEE
1nF
C95
10K
1
2
3
4
VCC
*WC
SCL
SDA
DGND
6
C109
E0
E1
E2
VSS
M24C64
DGND
5
1nF
10K
DGND
4
1nF
C98
This Document can not be used without Samsung’s authorization.
3
1nF
C121
DEBUG_RXD
DEBUG_TXD
DGND
2
1nF
C115
D
E
F
1
1nF
C142
10K
100nF
Service Manual
C127
R174
C307
A
B
C
D
E
F
Samsung Electronics
A
B
C
D
E
F
1
1
Samsung Electronics
2
2
3
3
4
CN17-1
00-6232-030-807-800
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
ADDR(2)
ADDR(3)
ADDR(4)
ADDR(5)
ADDR(6)
ADDR(7)
ADDR(8)
DATA(31)
DATA(30)
DATA(29)
DATA(28)
DATA(27)
DATA(26)
DATA(25)
DATA(24)
+3.3V +5V
DGND
5
5
CLX-3160FN Only
4
DATA(31:24)
ADDR(2:8)
nCS_MODEM
nRD
nWR
nRST_MODEM
nINT_MODEM
KEYCLICK
6
6
7
Engineer K.C.LEE
Drawn by
R&D CHK S.D.AN
DOC CTRL CHK
MFG ENGR CHK
7
This Document can not be used without Samsung’s authorization.
TITLE:
8
Digtal Printing Division
R&D 5
Size
A3
11/15
CLP-300(N)/CLX-3160N(FN)
Main_V0.11
8
SmartDAA Interface
A
B
C
D
E
F
Service Manual
A
B
C
D
E
F
1
1
Service Manual
2
LSU
CN22-1
DF11-14DP-2DSA
1
2
3
4
5
6
7
8
9
10
11
12
13
14
2
R168
100
R143
100
R103
100
R169
100
R138
100
C306
3
C266
R167
100
4
4
+5V
7
6
5
DGND
C241
100nF
1
U22-3
DM7407MX
DGND
DGND
C237
100nF
R118
5.1K
+3.3V
2
DM7407MX14
U22-1
R117
100
3
U22-2
DM7407MX
C284
10nF
DGND
4
C285
1nF
C260
10nF
DGND
9
DGND
DM7407MX
U22-4
8
R139
100
R158
10K
+5V_LSU
R171
1K
+5V_LSU
+5V
+5V
R145
10K
R144
10K
R137
10K
+5V_LSU
10uF
16V
2402-001049
DGND
DGND
100nF
NC5
15pF
+5V_LSU
NC4
15pF
DGND
DGND
C209
10uF
16V
2402-001049
+5V
C300
100nF
50V
2 1
D36
KDS226 3
NOT USED
DGND
C223
100nF
+24V
DGND
C233
47uF
50V
DGND
3
5
5
6
nHSYNC1
nLD_EN
VDO1_minus
VDO1_plus
LSU_SH1
LD_POWER1
LSU_MOT_CLK
nLSU_READY
nLSU_MOTOR_EN
6
7
Engineer K.C.LEE
Drawn by
R&D CHK S.D.AN
DOC CTRL CHK
MFG ENGR CHK
7
TITLE:
This Document can not be used without Samsung’s authorization.
8
Digtal Printing Division
R&D 5
Size
A3
12/15
CLP-300(N)/CLX-3160N(FN)
Main_V0.11
8
LSU
A
B
C
D
E
F
Samsung Electronics
A
B
C
D
E
F
B
1
1
1
B
6
4
2
5
3
1
DF11-6DP-2DSA
CN20-1
+5V
R5
150
2
R13
100
R14
47K
+3.3V
DGND
+3.3V
R164
47K
R149
100
2
R150
100
R165
47K
+3.3V
DGND
R148
150
+5V
DGND
R163
150
+5V
3
2
1
CN5-1
35303-0350
DEVE_HOME
B
Samsung Electronics
3
3
2
1
1
D6
KDS226
2
D32
KDS226
2
D33
KDS226
3
1
DGND
C20
10nF
DGND
C263
10nF
DGND
C264
10nF
3
nP_EMPTY
nREGI_SENS
3
nDEV_HOME
4
1
+3.3V
2
8
7
6
5
4
3
2
1
CN18-1
DF11-8DP-2DSA
SCF
3301-001122
D4
3
KDS226
FUSER THER.
2
1
CN8-1
5045-02A
4
DGND
L2
INSTPAR
L3
INSTPAR
C34
1nF
1
5
+3.3V
U5-1
3
2
6
8
1
DGND
LM393D 4
R20
5.6K
C21
10nF
3
6
3
R47
4.7K
7
2
3
D10
MMSD914T1
Q4
MMBT2222ALT1
+3.3V
6
5
DGND
100
100
0
R19 33K
R31
3K,1%
R33
R153
1
7
LM393D
U5-2
R126
10K
R44
4.7K
R41
1K
R132
10K
FUSER_ON
nFUSER_EN
FUSER_THERM1
FUSER_THERM2
SCF_RXD
SCF_TXD
8
Digtal Printing Division
R&D 5
nSCF_RDY
TITLE:
CLP-300(N)/CLX-3160N(FN)
Main_V0.11
8
Size
A3
A
B
C
D
E
F
Service Manual
DEVE_HOME,SCF,FUSER THER 13/15
C270
1nF
MFG ENGR CHK
DOC CTRL CHK
R&D CHK S.D.AN
Drawn by
Engineer K.C.LEE
C268 C246
1nF 1nF
DGND
R127
1K
7
R155
R32
30K,1%
3
D30
D26
D25
KDS226 KDS226 KDS226
1 2
1 2
1 2
C81
100nF
R18
15.4K,1%
R24
20K
1%
+3.3V
3
2
Q1
MMBT2222ALT1
DGND
C279
100nF
+24V +3.3V
C280
100nF,50V
DGND
5
This Document can not be used without Samsung’s authorization.
1
DEV_SOL
CN4-1
5045-02A
1
2
D8
M4
+24VF
C19
100nF
50V,10%
2203-005249
DGND
560
Q7
MMBT2222ALT1
R45
1
3
CN10-1
5045-03A
PTL
PTL
3
2
1
ITB_CLUTCH
DEV_CLUTCH
THV_CLUTCH
D7
M4
4
Q6
MMBT2222ALT1
1
C43
100nF
50V,10%
2203-005249
+24VF
3
DGND
2
DGND
R130
1
Q13
1
2
3
MMBT2222ALT1
Q14
4.7K
1nF
3
+24VF
R39
1.2K
DGND
R140
R42
1.2K
470
0
R129
R128
5
ITB_CLUTCH
PTL_LAMP
6
BLDC
2
1
2
3
4
5
6
7
8
9
10
1
+24VF
+3.3V
+5V
C11
100nF
100
100
4
6
8
10
12
DGND
R125
3K
1%
2
+3.3V
+5V +3.3V
R21
RA2
10K
R22
CN19-1
DF11-12DP-2DSA
1
3
5
7
9
11
2
DEVE & ITB JOINT
DGND
DF11-10DP-2DSA
CN2-1
+3.3V
1
1nF
R35
C44
3
MMBT2222ALT1
2
2
D37
KDS226
10nF
C30
2
DGND
C5
100nF
50V,10%
2203-005249
DGND
Q3
MMBT2222ALT1
1
1.2K
ERASE_LAMP
1.2K
DGND
10nF
2
D3
M4
3
C304
100nF
50V,10%
2203-005249
+24VF
DGND
3
3 DGND
D38
KDS226
C56
T2_CLUTCH
1
CN7-1
5045-03A
2
3
2
DGND
3
R198
33
R199
33
100nF
C29
A
B
C
REGI_CLUTCH
1
2
D34
M4
REGI_CLUTCH
SCL
SDA
WASTE_LEVEL
WASTE_EMPTY
DGND
7
1
1
Drawn by
R&D CHK S.D.AN
DOC CTRL CHK
BLDC_MOTOR_READY
R160
4.7K
R122
10K
8
nITB_HOME
PTL_LAMP
INNER_TEMP
Digtal Printing Division
R&D 5
CLP-300(N)/CLX-3160N(FN)
Main_V0.11
PWM_MOT
+5V
8
Size
A3
BLDC, CLUTCH, DEVE & ITB JOINT 14/15
MFG ENGR CHK
7
nBLDC_MOTOR_EN
DGND
3
D5
KDS226
2
D31 3
KDS226
100nF
Engineer K.C.LEE
C281
TITLE:
100nF
C33
6
1nF
3
R166
1.2K
PICKUP_CLUTCH
5
C278
Q16
MMBT2222ALT1
1
C305
100nF
50V,10%
2203-005249
+24VF
DGND
560
Q10
MMBT2222ALT1
R119
1
4
L11
INSTPAR
C265
This Document can not be used without Samsung’s authorization.
3
C282 10nF
1nF
2
100nF
C252
2
DGND
D35
M4
3
2
DGND
B
C262
CN24-1
35303-0350
2
1
PICK UP
1
CN25-1
5045-02A
1
100nF
C261
D
E
F
B
Service Manual
C292 10nF
R157 4.7K
R156 4.7K
C68
C283 1nF
1nF
C245
1nF
C271 1nF
1nF
4.7K
C79
4.7K
R37
R40
R141 4.7K
R120 4.7K
A
B
C
D
E
F
Samsung Electronics
A
B
C
1
HVPS
+24VF
DGND
CN21-1
DF11-24DP-2DSA(20)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
DGND
2
C294
100nF
10nF 10nF
C242 C297 C274
10nF
DGND
N.C
+5V
7
U20-1
DM7407MX 14
2
R134
10K
10K
1
3
5
3
C251
100nF
U20-6
13 DM7407MX
DGND
12
U20-5
11 DM7407MX
U22-6
13 DM7407MX
U20-4
9 DM7407MX
10
8
12
11
DGND
DGND
C258
10nF
1
+3.3V
3
10K
R146
100
2
D24
KDS226
3
R135
R180
47K
R116
3K
3K,1%
DGND
U20-2
DM7407MX
4
U20-3
DM7407MX
6
R159
10K
U22-5
DM7407MX
10
R124
100nF
C249
+5V
1nF
17
C253
18
1nF
19
DGND
C298
nDEV_EN
4
PWM_DEV_VPP
PWM_DEV_AC
PWM_DEV_DC
5
+5V
C166
100nF
DGND
6
+24V
C185
100nF
2401-000042
PWM_MHV
nTHV_EN
C208
100uF
50V
2401-000207
+24VA +24VF
C196
100nF
2401-000207
C240
100uF
50V
7
SMPS
14
12
10
8
6
4
2
15
13
11
9
7
5
3
1
CN15-1
DF11-16DP-2DSA
16
1
CN16-1
5096-02C
1.2K
FAN_MAIN
WASTE_LED
Q19
MMBT2907A
3
nCOVER_OPEN
R187
560
2
DGND
Engineer K.C.LEE
R&D CHK S.D.AN
Drawn by
DOC CTRL CHK
MFG ENGR CHK
7
R178
6.2K
R179
300
TITLE:
8
R104
5.1K
R99
22K
+24VF
FUSER_ON
+24VA +24VF
1
+3.3V
2
D21 3
KDS226
C225
100nF
Digtal Printing Division
R&D 5
8
Size
A3
A
B
C
D
E
F
Service Manual
HVPS, SMPS, COVER_OPEN 15/15
CLP-300(N)/CLX-3160N(FN)
Main_V0.11
Q18
MMBT2222ALT1
1
+24V_COVER SWITCH
2
CN26-1
35303-0250
ITHV_READ
R188
4.7K
1
1.2K
+5V_COVER SWITCH
R123
R136
1
2
2
THV_READ
DGND
Q15
MMBT2222ALT1
1
1
Q17
MMBT2222ALT1
6
+5V
+5V_LSU
C171
100uF
16V
C293
100nF 2203-005249
PWM_ITHV
+24VF
PWM_THV
D28
M4
3
2
3
DGND
2
DGND
5
3
MHV_READ
nP_EXIT
DEV_SOL1
DEV_SOL2
DEV_SOL3
DEV_SOL4
OUT_TEMP
4
This Document can not be used without Samsung’s authorization.
1nF
20
1nF
C290
21
1nF
C287
1nF
22
1nF
NC6
C299
23
24
1nF
NC7
2
1nF
C272
1nF
D
E
F
Samsung Electronics
1
1nF
C288
C275
1nF
1nF
C296
1nF
C247
C276 1nF
1nF
C257
C259
R131 4.7K
R147 4.7K
C273
C309
100nF
Service Manual
This Document can not be used without Samsung’s authorization.
Samsung Electronics
Samsung Electronics
This Document can not be used without Samsung’s authorization.
Service Manual
Service Manual
This Document can not be used without Samsung’s authorization.
Samsung Electronics
Samsung Electronics
This Document can not be used without Samsung’s authorization.
Service Manual
Service Manual
This Document can not be used without Samsung’s authorization.
Samsung Electronics
Samsung Electronics
This Document can not be used without Samsung’s authorization.
Service Manual
Service Manual
This Document can not be used without Samsung’s authorization.
Samsung Electronics
Samsung Electronics
This Document can not be used without Samsung’s authorization.
Service Manual
Service Manual
This Document can not be used without Samsung’s authorization.
Samsung Electronics
Samsung Electronics
This Document can not be used without Samsung’s authorization.
Service Manual
12. Reference Information
This chapter contains the tools list, list of abbreviations used in this manual, and a guide to the
location space required when installing the printer. A definition of tests pages and Wireless
Network information definition is also included.
12.1 Tools for Troubleshooting
Service Manual
Samsung Electronics
12.2 Acronyms and Abbreviations
The table below explains the abbreviations and acronyms used in this service manual. Where abbreviations
or acronyms are used in the text please refer to this table.
Service Manual
Samsung Electronics
Service Manual
Samsung Electronics
12.3 Select a location for the printer
• Leave enough room to open the printer trays, covers, and allow for proper ventilation. (see diagram
below)
• Provide the proper environment :
- A firm, level surface
- Away from the direct airflow of air conditioners, heaters, or ventilators
- Free of extreme fluctuations of temperature, sunlight, or humidity
- Clean, dry, and free of dust
Service Manual
Samsung Electronics
12.4 A4 ISO 19752 Standard Pattern
This test page is reproduced at 70% of the normal A4 size
Service Manual
Samsung Electronics