11166_sbd-1-manual

Before using your new SBD-1, please read this manual
thoroughly and use the system properly and safely.
After reading this manual, store it in a safe place.
S.BUS Decoder
Thank you for purchasing an SBD-1, S.BUS *1
decoder. The SBD-1 is a converter for using
conventional servos (other than S.BUS servo*2) with
the S.BUS system.
There are five types of SBD-1 available as follows.
Type
S.BUS Decoder
SBD-1
INSTRUCTION MANUAL
200
400
600
1100
1600
Total Length
200mm (8in.)
400mm (16in.)
600mm (24in.)
1,100mm (43in.)
1,600mm (63in.)
*1
S.BUS: Serial communication system for Futaba R/C system
*2
Use the S.BUS hub as the extension code used for the S.BUS servo. Also SBD-1 can be used.
Usage Precautions
CAUTION
WARNNG
not connect any device (gyro, battery,
use in the state in which the
Do
Always
etc.) other than servos to the servo
SBD-1 is firmly attached to the fuselage
connector of the SBD-1. There is the danger of
erroneous operation or damage.
not connect an S.BUS connector
Do
of the SBD-1 to other than an S.BUS
servo connection port. There is the danger of
erroneous operation or damage.
of the airplane or helicopter. There is the danger
of loss of control and crashing if the connector is
disconncted by vibration and shock.
Futaba Corp. will not be responsible for
damage caused by combination with other
than Futaba Genuine parts.
Name of Each Part and Accessories
<Accessories>
Channel No. Label
SBD-1
•Put the channel No. label on the servo connector
for the identification of channel No..
Instruction manual (this manual)
SX1
to the S.BUS servo connection port of the
SBC-1.
2C o n n e c t t h e b a t t e r y t o t h e b a t t e r y
connection port of the SBC-1.
*Status display LED blinks slowly. (About 1 sec/time)
*During channel setting, the LED blinks quickly
(about 5 times/sec). When the LED changes to a
steady light, channel setting is complete.
6To
set the channel of other ser vo
connection por ts, quickly press and
release the setting switch and repeat steps
4 and 5.
3Quickly press and release the SBC-1 setting
switch and select the servo connection port
at which the channel is to be set.
*Each time the switch is pressed, the set servo
connection port and the number of times the LED
blinks change.
SBC-1
S e t t i n g sw i t c h LED display
operation
W h e n p ow e r 1 shor t blink
turned on
each second
Switch pressed 2 s h o r t bl i n k s
a n d r e l e a s e d each second
quickly
Connector (SX2)
selected.
Switch pressed
and released
quickly
Connector (SX3)
selected.
3 s h o r t bl i n k s
each second
SBD-1 servo connector selection
Connector (SX1)
selected.
*(Channel confirmation)
When the operation position of the channel selector
switch and the channel set at the connector during
the SBD-1 servo connector selection coincide, the
LED changes to a steady light.
Usage Method
•Connection
1Connect the S.BUS connector of the SBD-1
to the receiver S.BUS connection port or
S.BUS hub.
2Connect a conventional servo or an S.BUS
servo to the servo connector of the SBD-1.
*When an S.BUS servo was connected, that servo
will operate as a conventional servo. However,
it operates on the channel set at the servo
connector of the SBD-1 instead of the channel set
at the servo itself.
to the receiver S.BUS connection port or S.BUS hub
Conventional servo
(or S.BUS servo)
4Set
SX1
the SBC-1 channel selector switch to
the channel you want to set.
5Hold down the setting switch (about 1
second).
SX2
Meaning of Special Markings
[SBD-1 Ratings]
Pay special attention to safety where indicated by the following marks:
Procedures which may lead to dangerous conditions and
cause death/serious injury if not carried out properly.
(Middle)
DANGER
(Lower)
WARNING
Procedures which may lead to a dangerous condition or
cause death or serious injury to the user if not carried out
properly, or procedures where the probability of superficial
injury or physical damage is high.
CAUTION
Procedures where the possibility of serious injury to the user
is small, but there is a danger of injury, or physical damage,
if not carried out properly.
SX2
SX3
Servo connector
Channel Setting
Before installing the SBD-1 to the fuselage, set
each channel at each servo connector (SX1~3).
Use the SBC-1 S.BUS channel changer or CIU-2
USB adapter (PC-Link software for setting) to set
the channel.
1Connect the S.BUS connector of the SBD-1
SX3
(Upper)
S.BUS connector
•Channel setting by SBC-1
*S.BUS decoder channel setting is impossible with
the S.BUS receiver R6108SB.
*PC-Link software can be downloaded from the
home page of your region's Futaba importer.
= Prohibited
= Mandatory
•Dimensions:
41.8x12.3x8.4mm
(1.65x0.48x0.33in.)
(excluding protruding)
•Weight:
6.9/10.8/14.7/24.5/34.3g
(0.24/0.38/0.52/0.86/1.21oz.)
•Power requirement:
Ni-Cd, Ni-MH 4 to 5 cells
equivalent battery (Futaba)
•O p e r a t i n g t e m p e r a t u r e
range: -10 to +45°
©Copyright 2010. No part of this manual may be reproduced in any form without prior permission. The contents of this
manual are subject to change without prior notice. While this manual has been carefully written, there may be inadvertent
errors or omissions. Please contact our service center if you feel that any corrections or clarifications should be made.
FUTABA CORPORATION Phone: +81 475 32 6982, Facsimile: +81 475 32 6983
1080 Yabutsuka, Chosei-mura, Chosei-gun, Chiba 299-4395, Japan
1M23N23401
©FUTABA CORPORATION
2010, 2
(1)