Bosch UML-202 Instruction manual

Bosch 20-inch High-resolution LCD Monitor
UML-202-90
en
Instruction Manual
UML-202-90
Table of Contents | en
iii
Table of Contents
1
Safety
1
1.1
Important Safety Instructions
1
1.2
Safety precautions
3
1.3
Important notices
4
1.4
Customer Support and Service
8
2
Unpacking
9
2.1
Parts List
9
3
Exploded View
10
4
Remote Control
12
4.1
Remote Control Battery Installation
13
5
Description
14
5.1
Features
14
5.2
Power
14
6
Installing the UML-202-90
15
6.1
Ventilation
15
6.2
Mounting the UML-202-90
15
6.2.1
Desktop Installation
15
6.2.2
Wall Mount Installation
16
6.3
Connecting the Composite Video Signal to the Monitor
16
6.4
Connecting the Y/C (S-Video) Signal to the Monitor
17
6.5
Connecting Audio to the Monitor
17
6.5.1
Connecting PC Audio
17
6.6
Connecting the PC Signal to the Monitor
17
6.6.1
HDMI
17
6.6.2
DVI
18
6.6.3
VGA
18
6.7
Single / Multiple Monitor Configuration
19
7
Navigating the Monitor
20
7.1
Navigating the Front Panel
20
7.2
Navigating the Monitor On-screen Display (OSD)
21
7.3
On-screen Display Menus
21
7.4
Custom Menu
22
7.5
Picture / Sound Menu
23
7.6
PIP Menu
24
7.7
Setup Menu
25
8
Power Management
26
8.1
Power Consumption
26
Bosch Security Systems, Inc.
Instruction Manual
F01U076723 | 1.0 | 2007.09
iv
en | Table of Contents
UML-202-90
8.2
LED Indicator
26
9
TroubleShooting Guide
27
10
Maintenance
28
11
Technical Specifications
29
F01U076723 | 1.0 | 2007.09
Instruction Manual
Bosch Security Systems, Inc.
UML-202-90
Bosch Security Systems, Inc.
Table of Contents | en
Instruction Manual
v
F01U076723 | 1.0 | 2007.09
1
en | Safety
UML-202-90
1
Safety
1.1
Important Safety Instructions
Read, follow, and retain for future reference all of the following safety instructions. Heed all
warnings on the unit and in the operating instructions before operating the unit.
1.
Cleaning - Unplug the unit from the outlet before cleaning. Follow any instructions
provided with the unit. Generally, using a dry cloth for cleaning is sufficient, but a moist
fluff-free cloth or leather shammy may also be used. Do not use liquid cleaners or aerosol
cleaners.
2.
Heat Sources - Do not install the unit near any heat sources such as radiators, heaters,
stoves, or other equipment (including amplifiers) that produce heat.
3.
Ventilation - Any openings in the unit enclosure are provided for ventilation to prevent
overheating and ensure reliable operation. Do not block or cover these openings. Do not
place the unit in an enclosure unless proper ventilation is provided, or the manufacturer's
instructions have been adhered to.
4.
Water - Do not use this unit near water, for example near a bathtub, washbowl, sink,
laundry basket, in a damp or wet basement, near a swimming pool, in an outdoor
installation, or in any area classified as a wet location. To reduce the risk of fire or
electrical shock, do not expose this unit to rain or moisture.
5.
Object and liquid entry - Never push objects of any kind into this unit through openings
as they may touch dangerous voltage points or short-out parts that could result in a fire
or electrical shock. Never spill liquid of any kind on the unit. Do not place objects filled
with liquids, such as vases or cups, on the unit.
6.
Lightning - For added protection during a lightning storm, or when leaving this unit
unattended and unused for long periods, unplug the unit from the wall outlet and
disconnect the cable system. This will prevent damage to the unit from lightning and
power line surges.
7.
Controls adjustment - Adjust only those controls specified in the operating instructions.
Improper adjustment of other controls may cause damage to the unit. Use of controls or
adjustments, or performance of procedures other than those specified, may result in
hazardous radiation exposure.
8.
Overloading - Do not overload outlets and extension cords. This can cause fire or
electrical shock.
9.
Power cord and plug protection - Protect the plug and power cord from foot traffic,
being pinched by items placed upon or against them at electrical outlets, and its exit
from the unit. For units intended to operate with 230 VAC, 50 Hz, the input and output
power cord must comply with the latest versions of IEC Publication 227 or IEC Publication
245.
10. Power disconnect - Units with or without ON/OFF switches have power supplied to the
unit whenever the power cord is inserted into the power source; however, the unit is
operational only when the ON/OFF switch is in the ON position. The power cord is the
main power disconnect device for switching off the voltage for all units.
11. Power sources - Operate the unit only from the type of power source indicated on the
label. Before proceeding, be sure to disconnect the power from the cable to be installed
into the unit.
–
For battery powered units, refer to the operating instructions.
–
For external power supplied units, use only the recommended or approved power
supplies.
F01U076723 | 1.0 | 2007.09
Instruction Manual
Bosch Security Systems, Inc.
UML-202-90
Safety | en
–
2
For limited power source units, this power source must comply with EN60950.
Substitutions may damage the unit or cause fire or shock.
–
For 24 VAC units, voltage applied to the unit's power input should not exceed ±10%,
or 28 VAC. User-supplied wiring must comply with local electrical codes (Class 2
power levels). Do not ground the supply at the terminals or at the unit's power
supply terminals.
–
If unsure of the type of power supply to use, contact your dealer or local power
company.
12. Servicing - Do not attempt to service this unit yourself. Opening or removing covers may
expose you to dangerous voltage or other hazards. Refer all servicing to qualified service
personnel.
13. Damage requiring service - Unplug the unit from the main AC power source and refer
servicing to qualified service personnel when any damage to the equipment has occurred,
such as:
–
the power supply cord or plug is damaged;
–
exposure to moisture, water, and/or inclement weather (rain, snow, etc.);
–
liquid has been spilled in or on the equipment;
–
an object has fallen into the unit;
–
unit has been dropped or the unit cabinet is damaged;
–
unit exhibits a distinct change in performance;
–
unit does not operate normally when the user correctly follows the operating
instructions.
14. Replacement parts - Be sure the service technician uses replacement parts specified by
the manufacturer, or that have the same characteristics as the original parts.
Unauthorized substitutions may cause fire, electrical shock, or other hazards.
15. Safety check - Safety checks should be performed upon completion of service or repairs
to the unit to ensure proper operating condition.
16. Installation - Install in accordance with the manufacturer's instructions and in
accordance with applicable local codes.
17. Attachments, changes or modifications - Only use attachments/accessories specified by
the manufacturer. Any change or modification of the equipment, not expressly approved
by Bosch, could void the warranty or, in the case of an authorization agreement, authority
to operate the equipment.
Bosch Security Systems, Inc.
Instruction Manual
F01U076723 | 1.0 | 2007.09
3
1.2
en | Safety
UML-202-90
Safety precautions
DANGER! High risk:
This symbol indicates an imminently hazardous situation such
as “Dangerous Voltage” inside the product.
If not avoided, this will result in an electrical shock, serious
bodily injury, or death.
WARNING! Medium risk:
!
Indicates a potentially hazardous situation.
If not avoided, this could result in serious bodily injury or death.
CAUTION! Medium risk:
!
Indicates a potentially hazardous situation.
If not avoided, this may result in minor or moderate injury.
Alerts the user to important instructions accompanying the
unit.
CAUTION! Low risk: (without safety alert symbol)
Indicates a potentially hazardous situation.
if not avoided, this may result in property damage or risk of
damage to the unit.
NOTICE!
i
F01U076723 | 1.0 | 2007.09
This symbol indicates information or a company policy that
relates directly or indirectly to the safety of personnel or
protection of property.
Instruction Manual
Bosch Security Systems, Inc.
UML-202-90
1.3
Safety | en
4
Important notices
Accessories - Do not place this unit on an unstable stand, tripod, bracket, or mount. The unit
may fall, causing serious injury and/or serious damage to the unit. Use only with the cart,
stand, tripod, bracket, or table specified by the manufacturer. When a cart is used, use
caution and care when moving the cart/apparatus combination to avoid injury from tip-over.
Quick stops, excessive force, or uneven surfaces may cause the cart/unit combination to
overturn. Mount the unit per the manufacturer's instructions.
All-pole power switch - Incorporate an all-pole power switch, with a contact separation of at
least 3 mm in each pole, into the electrical installation of the building.
If it is needed to open the housing for servicing and/or other activities, use this all-pole switch
as the main disconnect device for switching off the voltage to the unit.
Coax grounding:
–
Ground the cable system if connecting an outside cable system to the unit.
–
Connect outdoor equipment to the unit's inputs only after this unit has had its grounding
plug connected to a grounded outlet or its ground terminal is properly connected to a
ground source.
–
Disconnect the unit's input connectors from outdoor equipment before disconnecting the
grounding plug or grounding terminal.
–
Follow proper safety precautions such as grounding for any outdoor device connected to
this unit.
U.S.A. models only - Section 810 of the National Electrical Code, ANSI/NFPA No.70, provides
information regarding proper grounding of the mount and supporting structure, grounding of
the coax to a discharge unit, size of grounding conductors, location of discharge unit,
connection to grounding electrodes, and requirements for the grounding electrode.
NOTICE!
i
This device is intended for use in public areas only.
U.S. federal law strictly prohibits surreptitious recording of oral
communications.
Disposal - Your Bosch product was developed and manufactured with high-quality material
and components that can be recycled and reused. This symbol means that electronic and electrical appliances, which have reached the end of their working life, must be collected and disposed of separately from household waste material. Separate collecting systems are usually in
place for disused electronic and electrical products. Please dispose of these units at an environmentally compatible recycling facility, per European Directive 2002/96/EC.
Environmental statement - Bosch has a strong commitment towards the environment. This
unit has been designed to respect the environment as much as possible.
Fuse rating - For security protection of the device, the branch circuit protection must be
secured with a maximum fuse rating of 16A. This must be in accordance with NEC800 (CEC
Section 60).
Grounding and polarization - This unit may be equipped with a polarized alternating current
line plug (a plug with one blade wider than the other blade). This safety feature allows the
plug to fit into the power outlet in only one way. If unable to insert the plug fully into the
outlet, contact a locally certified electrician to replace the obsolete outlet. Do not defeat the
safety purpose of the polarized plug.
Alternately, this unit may be equipped with a 3-pole grounding plug (a plug with a third pin for
earth grounding). This safety feature allows the plug to fit into a grounded power outlet only.
If unable to insert the plug into the outlet, contact a locally certified electrician to replace the
obsolete outlet. Do not defeat the safety purpose of the grounding plug.
Bosch Security Systems, Inc.
Instruction Manual
F01U076723 | 1.0 | 2007.09
5
en | Safety
UML-202-90
Moving - Disconnect the power before moving the unit. Move the unit with care. Excessive
force or shock may damage the unit and the hard disk drives.
Outdoor signals - The installation for outdoor signals, especially regarding clearance from
power and lightning conductors and transient protection, must be in accordance with NEC725
and NEC800 (CEC Rule 16-224 and CEC Section 60).
Permanently connected equipment - Incorporate a readily accessible disconnect device in
the building installation wiring.
Pluggable equipment - Install the socket outlet near the equipment so it is easily accessible.
Power disconnect - Units have power supplied whenever the power cord is inserted into the
power source. The power cord is the main power disconnect for all units.
Power lines - Do not locate the camera near overhead power lines, power circuits, or
electrical lights, nor where it may contact such power lines, circuits, or lights.
Rack-mount
–
Ventilation - Do not place this unit in a built-in installation or rack without proper
ventilation or adhering to the manufacturer's instructions. The equipment must not
exceed its maximum operating temperature requirements.
–
Mechanical loading - Properly mount the equipment in a rack to prevent a hazardous
condition due to uneven mechanical loading.
SELV
–
All the input/output ports are Safety Extra Low Voltage (SELV) circuits. SELV circuits
–
Because the ISDN circuits are treated like telephone-network voltage, avoid connecting
should only be connected to other SELV circuits.
the SELV circuit to the Telephone Network Voltage (TNV) circuits.
Video loss - Video loss is inherent to digital video recording; therefore, Bosch Security
Systems cannot be held liable for any damage that results from missing video information. To
minimize the risk of lost digital information, Bosch Security Systems recommends multiple,
redundant recording systems, and a procedure to back up all analog and digital information.
NOTICE!
i
F01U076723 | 1.0 | 2007.09
This is a class A product. In a domestic environment this
product may cause radio interference, in which case the user
may be required to take adequate measures.
Instruction Manual
Bosch Security Systems, Inc.
UML-202-90
Safety | en
6
FCC & ICES INFORMATION (commercial applications)
(U.S.A. and Canadian Models Only)
This device complies with part 15 of the FCC Rules. Operation is subject to the following
conditions:
–
this device may not cause harmful interference, and
–
this device must accept any interference received, including interference that may cause
undesired operation.
Note
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules and ICES-003 of Industry Canada. These limits
are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses, and
radiates radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of
this equipment in a residential area is likely to cause harmful interference, in which case the
user will be required to correct the interference at his expense.
Intentional or unintentional modifications, not expressly approved by the party responsible for
compliance, shall not be made. Any such modifications could void the user's authority to
operate the equipment. If necessary, the user should consult the dealer or an experienced
radio/television technician for corrective action.
The user may find the following booklet, prepared by the Federal Communications
Commission, helpful: How to Identify and Resolve Radio-TV Interference Problems. This booklet
is available from the U.S. Government Printing Office, Washington, DC 20402, Stock No. 004000-00345-4.
INFORMATIONS FCC ET ICES (commercial applications)
(modèles utilisés aux États-Unis et au Canada uniquement)
Ce produit est conforme aux normes FCC partie 15. la mise en service est soumises aux deux
conditions suivantes:
–
cet appareil ne peut pas provoquer d'interférence nuisible et
–
cet appareil doit pouvoir tolérer toutes les interférences auxquelles il est soumit, y
compris les interférences qui pourraient influer sur son bon fonctionnement.
AVERTISSEMENT: Suite à différents tests, cet appareil s’est révélé conforme aux exigences
imposées aux appareils numériques de Classe A en vertu de la section 15 du règlement de la
Commission fédérale des communications des États-Unis (FCC). Ces contraintes sont
destinées à fournir une protection raisonnable contre les interférences nuisibles quand
l'appareil est utilisé dans une installation commerciale. Cette appareil génère, utilise et émet
de l'energie de fréquence radio, et peut, en cas d'installation ou d'utilisation non conforme
aux instructions, générer des interférences nuisibles aux communications radio. L’utilisation
de ce produit dans une zone résidentielle peut provoquer des interférences nuisibles. Le cas
échéant, l’utilisateur devra remédier à ces interférences à ses propres frais.
Au besoin, l’utilisateur consultera son revendeur ou un technicien qualifié en radio/télévision,
qui procédera à une opération corrective. La brochure suivante, publiée par la Commission
fédérale des communications (FCC), peut s’avérer utile : « How to Identify and Resolve RadioTV Interference Problems » (Comment identifier et résoudre les problèmes d’interférences de
radio et de télévision). Cette brochure est disponible auprès du U.S. Government Printing
Office, Washington, DC 20402, États-Unis, sous la référence n° 004-000-00345-4.
AVERTISSEMENT: Ce produit est un appareil de Classe A. Son utilisation dans une zone
résidentielle risque de provoquer des interférences. Le cas échéant, l’utilisateur devra
prendre les mesures nécessaires pour y remédier.
Bosch Security Systems, Inc.
Instruction Manual
F01U076723 | 1.0 | 2007.09
7
en | Safety
UML-202-90
Disclaimer
Underwriter Laboratories Inc. (“UL”) has not tested the performance or reliability of the
security or signaling aspects of this product. UL has only tested fire, shock and/or casualty
hazards as outlined in UP’s Standard(s) for Safety for Information Technology Equipment, UL
60950-1. UL Certification does not cover the performance or reliability of the security or
signaling aspects of this product.
UL MAKES NO REPRESENTATIONS, WARRANTIES, OR CERTIFICATIONS WHATSOEVER
REGARDING THE PERFORMANCE OR RELIABILITY OF ANY SECURITY OR SIGNALING-RELATED
FUNCTIONS OF THIS PRODUCT.
Copyright
This user guide is the intellectual property of Bosch Security Systems, Inc. and is protected by
copyright.
All rights reserved.
Trademarks
All hardware and software product names used in this document are likely to be registered
trademarks and must be treated accordingly.
NOTICE!
This user guide has been compiled with great care and the
information it contains has been thoroughly verified. The text
i
was complete and correct at the time of printing. The ongoing
development of the products may mean that the content of the
user guide can change without notice. Bosch Security Systems
accepts no liability for damage resulting directly or indirectly
from faults, incompleteness or discrepancies between the user
guide and the product described.
More information
For additional information, please contact the Bosch Security Systems location nearest you or
visit our web site at www.boschsecuritysystems.com
F01U076723 | 1.0 | 2007.09
Instruction Manual
Bosch Security Systems, Inc.
UML-202-90
1.4
Safety | en
8
Customer Support and Service
If this unit needs service, contact the nearest Bosch Security Systems Service Center for
authorization to return and shipping instructions.
Service Centers
USA
Telephone: 800-366-2283 or 585-340-4162
Fax: 800-366-1329
Email: cctv.repair@us.bosch.com
Customer Service
Telephone: 800-289-0096
Fax: 585-223-9180
Email: security.sales@us.bosch.com
Technical Support
Telephone: 800-289-0096
Fax: 585-223-3508 or 717-735-6560
Email: technical.support@us.bosch.com
Repair Center
Telephone: 585-421-4220
Fax: 585-223-9180 or 717-735-6561
Email: security.repair@us.bosch.com
Canada
Telephone: 514-738-2434
Fax: 514-738-8480
Europe, Middle East & Asia Pacific Region
Telephone: 44 (0) 1495 274558
Fax: 44 (0) 1495 274280
Email: rmahelpdesk@solectron.com
More information
For additional information, please contact your Bosch Security Systems representative or visit
our web site at www.boschsecurity.com
Bosch Security Systems, Inc.
Instruction Manual
F01U076723 | 1.0 | 2007.09
UML-202-90
2
Unpacking | en
9
Unpacking
This equipment should be unpacked and handled with care. If an item appears to have been
damaged in shipment, notify the shipper immediately.
Verify that all the parts listed in the Parts List below are included. If any items are missing,
notify your Bosch Security Systems Sales or Customer Service Representative.
The original packing carton is the safest container in which to transport the unit and must be
used if returning the unit for service. Save it for possible future use.
2.1
Parts List
The following table lists the parts included:
Quantity
Part
1
UML-202-90 Color LCD Flat Panel Monitor
1
Installation manual
2
Power Cords, 3-wire with grounded plug 1.8 m (6 ft) long:
one with a U.S plug type and one with a European Continental plug type
1
VGA to VGA (D-SUB) cable, 1.5 m (5 ft)
1
DVI-D to DVI-D cable, 1.5 m (5 ft)
1
Remote control with two (2) batteries
1
Audio cable PC-style
Bosch Security Systems, Inc.
Instruction Manual
F01U076723 | 1.0 | 2007.09
10
3
en | Exploded View
UML-202-90
Exploded View
Fig. 3.1 Front Panel UML-202-90
Reference # Button
Description
1
Input Button
Selects the signal to be displayed
2
Menu Button
Selects the on-screen display (OSD)
3
Adjusts the value when in the OSD Scrolls up in the OSD
4
Adjusts the value when in the OSD Scrolls down in the OSD
or auto adjusts when in PC mode
5
Decreases the value when in the
Scrolls left in the OSD
OSD
6
Increases the value when in the
Scrolls right in the OSD
OSD
7
IR Sensor
Remote control sensor
8
LED Indicator
Power On (green)
Power Off, Standby (red)
9
F01U076723 | 1.0 | 2007.09
Power Button Display power (On/Off)
Instruction Manual
Bosch Security Systems, Inc.
UML-202-90
Exploded View | en
11
1
2
3
4
5
6
7
9
8
10
11
12
13
14
15 16
17
18
Fig. 3.2 Side and Bottom Panels UML-202-90
Side Panel
Bottom Panel
Reference #
Connector
Reference #
Connector
1
Video 1 (AV1) IN
12
HDMI IN
2
Video 1 (AV1) OUT
13
DVI IN
3
Video 2 (AV2) IN
14
D-SUB IN
4
Video 2 (AV2) OUT
15
PC Stereo IN
5
S-Video (Y/C) IN
16
Audio OUT
6
S-Video (Y/C) OUT
17
Component Y, Pb, Pr
and Sound L, R
7
Audio IN (AV1, S-Video)
8
Audio OUT (AV1,
18
DC 12 V IN
S-Video)
9
Audio IN (AV2)
10
Audio OUT (AV2)
11
12 V Adaptor
Bosch Security Systems, Inc.
Instruction Manual
F01U076723 | 1.0 | 2007.09
12
en | Remote Control
4
UML-202-90
Remote Control
This section details the functions and the usage of the Bosch remote control.
Button
Function
POWER
Turns the power ON and OFF.
SOURCE
Selects the PC or Video source.
Numbers
Numerals 0-9.
AUTO
Auto adjusts to the graphics adaptor.
MUTE
Mutes the sound.
MENU
Displays the OSD. Pressing the MENU button returns you to the Main
menu from anywhere in the OSD menus.
EXIT
Exits the OSD.
UP
Moves the cursor up in an OSD menu.
DOWN
Moves the cursor down in an OSD menu.
ENTER
Accepts your selection or displays the current mode when in the OSD
menu.
s
VOL
€
Moves the cursor left, decreases item values in an OSD menu, or
decreases sound.
Moves the cursor right, increases item values in an OSD menu, or
VOL
decreases sound.
PIP
Activates/deactivates Picture-In-Picture mode.
P. INPUT
Selects the PC or Video source for the PIP. Continuously press this button to change the selection.
P. POS
Moves the position of the sub picture for the PIP mode. Continuously
press this button to change the selection.
P. SIZE
Changes the size of the sub and main picture for the PIP mode. Continuously press this button to change the selection.
SWAP
Alternates between the main and sub picture for the PIP mode. Continuously press this button to change the selection.
ARC (Aspect
Selects the screen ratio when in Video mode. Continuously press this
Ratio Control) button to change the selection.
APC (Auto Pic- Selects the picture mode. Continuously press this button to change the
ture Control)
selection.
ACC (Auto
Selects the color mode. Continuously press this button to change the
Color Control) selection.
S. SET
Selects the sound mode main input or sub input (only available when
PIP is enabled).
PC
Selects the PC mode (HDMI, DVI, PC). Continuously press this button to
change the selection.
AV
Selects the AV mode (AV1, AV2, S-Video). Continuously press this button to change the selection.
COMP
Selects the COMPONENT mode.
F01U076723 | 1.0 | 2007.09
Instruction Manual
Bosch Security Systems, Inc.
UML-202-90
Remote Control | en
4.1
13
Remote Control Battery Installation
1.
Turn the remote over (buttons facing down) and push down on the cover and slide it off.
2.
Insert two (2) new AAA alkaline batteries, matching the batteries to the (+) and (-) marks
inside the battery case.
Fig. 4.1 Battery Installation
3.
i
Slide the battery cover back into place.
NOTICE! Replace batteries when required or at least once a year. Dispose of used batteries
properly.
Bosch Security Systems, Inc.
Instruction Manual
F01U076723 | 1.0 | 2007.09
14
5
en | Description
UML-202-90
Description
The UML-202-90 20-inch (51-cm) Color Panel Display Monitor displays PAL or NTSC standard
color pictures in CCTV systems. The UML-202-90 monitor includes two (2) looping Composite
Video BNC connector inputs, two (2) looping Audio input RCA, and two (2) looping Y/C (SVideo) input using a 4-pin mini-DIN. In addition, this model also includes an Analog VGA input
using 15-pin D-sub to accommodate the increasing use of PCs and digital video devices in
security applications, an HDMI (High Definition Multimedia Input), DVI, PC-RGB (VGA), RC
Audio In and Out, and Component Video (Y/Pb/Pr) connectors.
Monitor control functions are accessed via the front panel push buttons and On-screen Display (OSD). See Figure 3.1 on page 10 for front panel descriptions.
5.1
Features
This high-performance, 20-inch Color Panel Display Monitor with 1600 X 1200 pixels resolution has been designed to display Analog VGA and Composite Video signals.
5.2
–
90 to 256 VAC Power Supply
–
NTSC/PAL Auto-Detect
–
1600 x 1200 High-Resolution Display
–
VGA Input
–
Composite Video Input
–
Y/C Input (S-Video)
–
On-screen Display (OSD) with Multiple Languages
Power
Model No.
Rated Voltage
Voltage Range
Power at Rated Voltage Sync Format
UML-202-90
120/230 VAC
90 to 256 V
70 W (max)
NTSC/PAL
50/60 Hz
F01U076723 | 1.0 | 2007.09
Instruction Manual
Bosch Security Systems, Inc.
UML-202-90
Installing the UML-202-90 | en
6
15
Installing the UML-202-90
This chapter outlines the procedures needed to install the UML-202-90 Series. A qualified service person should install the monitor and adhere to all local codes.
The UML-202-90 monitor is delivered with a 3-pole US-style power cord and a 3-pole Eurostyle power cord. Use the US-style power cord where 120 VAC, 60 Hz power is available; and
use the Euro-style power cord where 230 VAC, 50 Hz power is available. The monitor automatically adjusts to either power input voltage.
6.1
Ventilation
To prevent overheating, ensure that the ventilation openings on the rear of the monitor are not
covered.
6.2
Mounting the UML-202-90
The UML-202-90 is designed to be used on a desktop or mounted to a wall or rack.
6.2.1
Desktop Installation
The viewing angle of the LCD can be adjusted to fit the most comfortable monitoring status.
i
Min Degree
Max Degree
25o 122 mm
50o 192 mm
NOTICE! For the best viewing quality and holding support, the suggested bracket angle is 25°
to 50°.
Bosch Security Systems, Inc.
Instruction Manual
F01U076723 | 1.0 | 2007.09
16
en | Installing the UML-202-90
6.2.2
UML-202-90
Wall Mount Installation
The square mounting holes (100 mm (3.9 in.) centers) can be used for wall mount installation
using the optional UMM-LW-20B fixed mount or the UMM-LW-30B swivel/tilt mount.
Fig. 6.1 Mounting the Device
6.3
Connecting the Composite Video Signal to the Monitor
There are two (2) BNC connectors located on the rear side panel of the monitor for composite
video input and two (2) BNC connectors for composite video outputs (see Figure 3.2 on page
11).
NOTE: All video inputs are passive loop-through. The impedance is automatically set to
75 ohm by the input of the signal on the input connector, while operating in a single connection mode (see Figure 6.6 on page 19). If a cable is also connected to the output connector,
the video signal can be passed on to another monitor connected to it via the passive loopthrough function. Up to three (3) monitors may be connected in this manner (see Figure 6.7
on page 19).
i
NOTICE! To select between AV1 and AV2, press Input (see Figure 3.1 on page 10, Item 1)
located on the front of the monitor.
F01U076723 | 1.0 | 2007.09
Instruction Manual
Bosch Security Systems, Inc.
UML-202-90
6.4
Installing the UML-202-90 | en
17
Connecting the Y/C (S-Video) Signal to the Monitor
There is one (1) mini-DIN type connector for the S-Video (Y/C) input (see Figure 6.2 on page
17) on the rear side panel.
NOTE: Both Y and C inputs are terminated with 75 ohm.
Fig. 6.2 Y/C Connection Pinout
6.5
Reference
Input
1
GND
2
GND
3
Y-signal IN or OUT
4
C-signal IN or OUT
Connecting Audio to the Monitor
There are two (2) sets of mono audio connectors for audio input.
–
All audio inputs are active loop-through.
–
Audio 1 is associated with Video 1 or Y/C; Audio 2 is associated with Video 2.
Reference
Audio 1
Video 1
X
Video 2
S-video
6.5.1
Audio 2
X
X
Connecting PC Audio
The rear bottom panel has PC stereo audio IN and audio OUT. Connect with 1/8 in. mini phono
plug jack to Audio IN.
6.6
Connecting the PC Signal to the Monitor
There are three ways to connect the PC signal to the monitor.
6.6.1
HDMI
The monitor can be connected to the HDMI (High Definition Multimedia Input) by connecting a
HDMI cable (not supplied).
Fig. 6.3 HDMI Input
Bosch Security Systems, Inc.
Instruction Manual
F01U076723 | 1.0 | 2007.09
18
en | Installing the UML-202-90
6.6.2
UML-202-90
DVI
The monitor can be connected by using the supplied DVI-D cable and connecting it to the digital DVI-D signal.
Fig. 6.4 DVI Input
6.6.3
VGA
The monitor can be connected by connecting the analog VGA signal by using the provided VGA
cable (D-SUB to D-SUB).
Fig. 6.5 VGA Input
Pin #
Description
1
Red Video
2
Green Video
3
Blue Video
4
Ground
5
Ground
6
Red Ground
7
Green Ground
8
Blue Ground
9
N/A
10
Signal Cable Detect
11
Ground
12
SDA (for DDC)
13
H-Sync or H+V Sync
14
V-Sync
15
SCL (for DDC)
F01U076723 | 1.0 | 2007.09
Instruction Manual
Bosch Security Systems, Inc.
UML-202-90
6.7
Installing the UML-202-90 | en
19
Single / Multiple Monitor Configuration
Fig. 6.6 Single Monitor Configuration
Reference #
Description
1
Video Camera
2
VIDEO 2 (AV2) IN
3
VIDEO 2 (AV2) OUT
4
VCR
Fig. 6.7 Multiple Monitor Configuration
Reference #
Description
1
Video Camera
2
VIDEO 2 (AV2) IN
3
VIDEO 2 (AV2) OUT
Bosch Security Systems, Inc.
Instruction Manual
F01U076723 | 1.0 | 2007.09
20
en | Navigating the Monitor
UML-202-90
7
Navigating the Monitor
7.1
Navigating the Front Panel
Use the front panel to make any necessary OSD adjustments to the UML-202-90. See the figure below for an explanation of the front panel.
Fig. 7.1 Front Panel Buttons
Reference
Button
Description
1
Input Button
Selects the signal to be displayed
2
Menu Button
Selects the on-screen display (OSD)
3
Scrolls up in the OSD
4
Performs an Autoset when con-
Scrolls down in the OSD
nected to the VGA input, which
automatically adjusts the display
to match the graphics adapter.
5
Decreases the value
Scrolls left in the OSD
6
Increases the value
Scrolls right in the OSD
7
LED Indicator
Power On (green)
Standby, Suspend, Active Off (flashing red)
Unsupported mode (green)
Power Off (red)
8
F01U076723 | 1.0 | 2007.09
Power Button
Display power (On/Off)
Instruction Manual
Bosch Security Systems, Inc.
UML-202-90
Navigating the Monitor | en
7.2
21
Navigating the Monitor On-screen Display (OSD)
The UML-202-90 has two (2) modes, Video and PC. The UML-202-90 is programmed through
the on-screen display (OSD) menus. Each OSD shows a list of parameters or submenus that
the operator can select. To access the OSD menus, press the Menu button on the front panel
or on the remote control. Use the front panel of the UML-202-90 or remote control to make
any necessary adjustments to the OSD.
i
NOTICE! When you are navigating through the OSD menus, use the Input button to select a
menu and use the Menu button to exit a menu.
To navigate the set up menus, follow the steps below:
1.
2.
Connect the CVBS or VGA cable.
If required, press the Input button until a signal is displayed. NOTE: Menus are not available without a signal applied.
3.
Power on the unit by pressing the power button (see Figure 7.1 on page 20).
4.
Press the Menu button to activate the main menu selections (see Figure 7.1 on page 20).
5.
Press the
6.
Press the Input button to enter the selected main menu.
7.
Press the
and
buttons to select a menu item.
8.
Press the
and
button to toggle the OSD values.
9.
Press the Menu button to exit the selected button and to return to the menu bar.
and
buttons to navigate the main menu bar.
10. Press the Menu button again to exit the OSD menu bar.
7.3
On-screen Display Menus
There are four (4) on-screen menus that allow you to customize your settings. Press the Menu
button to access the OSD menu.
Icon
Menu
Function
Custom
Adjusts the Brightness, Contrast, Color, Tint, and the Sharpness
level for video performance of the OSD.
Picture / Sound Adjusts the Picture Mode, Color Tone, Mute, Volume, Size, and the
PC settings.
PIP
Adjusts the Input Source, Size, Position, Swap, and the Sound
Select settings.
Set Up
Enables user to Reset the factory default settings and to adjust the
Language, OSD Tone, Blue Screen, and the Key Lock settings.
Bosch Security Systems, Inc.
Instruction Manual
F01U076723 | 1.0 | 2007.09
22
7.4
en | Navigating the Monitor
UML-202-90
Custom Menu
To access the Custom menu, press the Menu button on the front panel of the monitor. Next,
press the right arrow and then press the up and down arrows to select a submenu. Press the
left and right arrow buttons to increase or decrease the values. When finished, press the Menu
button to save any changes, then press the Menu button again to exit the OSD.
Custom
Brightness
Contrast
Color
Tint
Sharpness
:Move
50
50
50
50
20
:Input
:Menu
Fig. 7.2 Custom Menu (Video Mode)
Custom
Brightness
Contrast
:Move
:Input
50
50
:Menu
Fig. 7.3 Custom Menu (PC Mode)
Submenu
Definition
Brightness
Adjusts the brightness level for video performance (range 0-100).
Contrast
Adjusts the contrast level for video performance (range 0-100).
Color
Adjusts the overall intensity of the screen (range 0-100).
Tint
Adjusts the tint of the picture (range 0-100). NTSC only.
Sharpness
Adjusts the sharpness level for video performance (range 0-100).
F01U076723 | 1.0 | 2007.09
Instruction Manual
Bosch Security Systems, Inc.
UML-202-90
7.5
Navigating the Monitor | en
23
Picture / Sound Menu
To access the Picture / Sound menu, press the Menu button on the front panel of the monitor,
then press the left and right arrows to select the Picture / Sound icon. Press the up and down
arrows to select the Picture / Sound submenu.
Picture / Sound
Picture Mode
Color Tone
Mute
Volume
Size
NR
:Move
Custom
Normal
Off
20
4.3
On
:Input
:Menu
Fig. 7.4 Picture / Sound Menu (Video Mode)
Picture / Sound
Picture Mode
Color Tone
Mute
Volume
Size
PC
:Move
Custom
Normal
Off
20
4.3
:Input
:Menu
Fig. 7.5 Picture / Sound Menu (PC Mode)
Submenu
Definition
Picture Mode (Video Selects the automatic picture control mode. Choices are:
Mode)
–
Custom: User selected values of the Custom menu are applied.
–
Dynamic: Automatically adjusts the Brightness, Contrast, and
–
Standard: Applies factory default values.
Sharpness, maximizing the video quality in the picture.
Picture Mode (PC
Selects the automatic picture control mode. Choices are:
Mode)
–
Custom: User selected values of the Custom menu are applied.
–
High: Uses the following values: Brightness = 70, Contrast = 80
–
Middle: Uses the following values Brightness = 60, Contrast = 70.
–
Low: Uses the following values Brightness = 50, Contrast = 60.
Color Tone
Selects the color temperature. Choices are: Cool 9300K, Normal
6500K, Warm 5000K.
Mute
Enables/disables audio. Choices are: On and Off.
Volume
Controls built-in speaker output volume (range 0-100).
Bosch Security Systems, Inc.
Instruction Manual
F01U076723 | 1.0 | 2007.09
24
en | Navigating the Monitor
UML-202-90
Size (Video Mode)
Selects the Aspect Ratio Control mode. Choices are: 4:3, Panorama,
Zoom1, Zoom2, Wide.
NR (Video Mode)
Turns Noise Reduction on or off. Turning this feature OFF reduces the
video quality slightly, but improves the monitors response time to
MOTION.
PC (PC Mode)
Selects between Auto or manual adjustment of the desktop screen.
Auto Adjust: Auto synchronizes screen to graphics adaptor.
Manual choices are: Phase (range 0-100), H-Position (range 0-100), VPosition (range 0-100), Frequency (range 0-100).
7.6
PIP Menu
To access the PIP menu, press the Menu button on the front panel of the monitor, then press
the left and right arrows to select the PIP icon. Press the up and down arrows to select the
PIP submenu.
PIP
PIP
Input Source
Size
Position
Swap
Sound Select
:Move
On
AV1
Main
:Input
Submenu
Definition
PIP
On and Off
:Menu
Input Source
AV1, AV2, S-video
Size
Enables 3 screen sizes: full screen side by side, 4:3 side by side, and 4:3 corner (177 mm [3.03 in.] diagonal).
Position
Enables 4 positions: bottom right, top right, bottom left, top left.
Swap
Alternates between the main and sub picture for the PIP mode. Continuously
press to change selection.
Sound Select Main and Sub (only available when PIP is enabled)
F01U076723 | 1.0 | 2007.09
Instruction Manual
Bosch Security Systems, Inc.
UML-202-90
Navigating the Monitor | en
7.7
25
Setup Menu
To access the Setup menu, press the Menu button on the front panel of the monitor, then
press the left and right arrows to select the Setup icon. Press the up and down arrows to
select the Setup submenu.
Setup
Reset
Language
OSD Tone
Blue Screen
Key Lock
Firmware Version
:Move
:Input
English
Blue
Off
Off
1.2
:Menu
Submenu
Definition
Reset
Restores default settings.
Language
Adjusts the language of the OSD. Choices are: English, French, German, Italian, Dutch, Spanish, and Portuguese.
OSD Tones
Selects the type of background for the OSD menu. Choices are: Transparency and Blue.
Blue Screen
Enables or disables video loss indication. Choices are:
On: displays a blue background when video loss is detected.
Off: displays a black backgound when video loss is detected.
i
Key Lock
Enables or disables the Key Lock function.
Firmware Version
Displays the release level of the monitor firmware.
NOTICE! When key lock is enabled through the front panel, use either the remote control or
the front panel buttons to disable the key lock command. To disable the key lock feature using
the front panel buttons, press and hold both the Input and the Menu buttons until the monitor
displays the Key Unlocked message.
Bosch Security Systems, Inc.
Instruction Manual
F01U076723 | 1.0 | 2007.09
26
8
en | Power Management
UML-202-90
Power Management
This monitor features a power management system to “power down” upon receipt of the display power management signaling (DPMS) from a DPMS video card.
The DPMS-compliant video card performs this signaling system through not sending horizontal, vertical, or sync signal.
This monitor enters an appropriate mode through identifying each of the three modes of the
signaling system.
8.1
8.2
Power Consumption
Mode
Power Consumption
ON
70 W
STANDBY
10 W
SUSPEND
10 W
ACTIVE OFF
10 W
LED Indicator
The power management feature of the monitor is comprised of these stages:
Mode
LED Color
Monitor Operation
ON
Green
Normal operation
STANDBY
Flashes Red
Screen blanks after idle time and some electronic circuits or all circuitry in the monitor shuts down.
SUSPEND
ACTIVE OFF
UNSUPPORTED MODE
Green
Normal operation but the screen displays an error
message.
POWER OFF
F01U076723 | 1.0 | 2007.09
Red
Not operational.
Instruction Manual
Bosch Security Systems, Inc.
UML-202-90
9
TroubleShooting Guide | en
27
TroubleShooting Guide
Problem
Solution
No image is displayed on 1.
Check that the power cord of the monitor is securely con-
screen
nected into the wall outlet or grounded extension cable or
strip.
2.
3.
Power switch should be in the ON position and the LED lit.
Check that the Brightness and/or Contrast adjustments of the
display have not been turned down to minimum levels.
“Going to Sleep” mes-
1.
sage is displayed
The signal cable should be completely connected to the video
card/computer.
2.
The video card should be completely seated in its slot and the
computer switched ON.
Display image is not cen- Push the down key to activate the Autoset function.
tered, is too small, or too -orlarge in the PC mode
Adjust the Clock and Phase in the OSD submenu.
Vertical or horizontal
Push the down key to activate the Autoset function (for VGA inputs
noise is present in the
only).
picture
-orAdjust the Clock and Phase in the OSD submenu.
Incorrect colors
1.
Press the Menu button on the front panel of the monitor, then
press the right arrow to select the Color menu. Press the
down arrow on the front panel and select Cool, Warm, or Normal.
- or 2.
Press the Menu button on the front panel of the monitor, then
press the right arrow to select the Utility menu. Press the
down arrow on the front panel and select Recall to reset to
the default settings.
The error message “Out
PC is operating with either a resolution or timing mode that is not
of Range” is displayed
supported by the UML-202-90. Change the PC timing mode to one
of the valid combinations below:
640 x 480; 60/72/75 Hz
800 x 600; 60/72/75 Hz
1024 x 768; 60/70/75 Hz
1280 x 1024; 60/75 Hz
1600 x 1200; 60 Hz
Bosch Security Systems, Inc.
Instruction Manual
F01U076723 | 1.0 | 2007.09
28
en | Maintenance
10
UML-202-90
Maintenance
To clean the LCD panel, wipe off water droplets or oil immediately with absorbent cotton or a
soft lint-free cloth. Staining and discoloration may occur if left on the panel for long periods.
If the surface (polarizer) of the LCD panel is dirty or stained, use absorbent cotton or a soft
lint-free cloth to remove the residue as follows:
1.
2.
Turn off the computer or display.
Do not spray any liquid directly on the screen. Dampen a clean, soft, lint-free cloth with
water only (using a paper towel or dirty cloth can scratch the screen).
3.
Gently wipe the screen starting from the top of the screen to bottom wiping in a downward motion. Be careful not to press too hard to avoid damaging the screen.
4.
i
To avoid streaking, wipe the screen again with another clean, dry, lint-free cloth.
NOTICE! If water does not work, use a mild cleaner labeled for use with LCD panels, available
at office supply stores.
Do not use any of the following as a cleaning agent:
–
Ketone type materials
–
Ethyl alcohol
–
Ethyl acid
–
Tolulene
–
Methyl chloride
–
Ammonia
Use of these materials may permanently damage the polarizer due to a chemical reaction.
F01U076723 | 1.0 | 2007.09
Instruction Manual
Bosch Security Systems, Inc.
UML-202-90
11
Technical Specifications | en
29
Technical Specifications
Electrical
Rated Voltage
110/230 VAC, 50/60 Hz
Voltage Range
90 to 264
Power at Rated Voltage
70 W
Sync Format
PAL/NTSC
LCD Panel
TFT LCD
Screen Size (H x V)
408 x 306 mm (16 x 12 in.)
Viewable Picture Area
20.1 in. (53 cm) measured diagonally
Pixel Pitch (H x V)
0.255 x 0.255 mm (0.01 x 0.01 in.)
Resolution
1600 x 1200 pixels, 500 TV lines typical
Aspect Ratio
4:3
Display Colors
8-bit interface; 16.7 million colors
Response Time
16 ms (typical)
Backlight
Six (6) cold cathode fluorescent tubes, rated life 50,000 hours, at 50% brightness
LCD Panel Optical Characteristics
Luminance
300 cd/m2, hard-coating (3H), non-glare treatment
Contrast Ratio (CR)
800:1
Viewing Angle
178° horizontal, 178° vertical @ CR >= 10
Sync Format
PAL/NTSC
Video Input
Composite Video (CVBS)
1.0 Vp-p (0.5-1.5 Vp-p), automatic switching from 75 Ohm unbalanced termination
to Hi-Z with passive loop-through operation
Y/C (S-video)
0.7 Vp-p (Y-signal), 0.3 Vp-p (C-signal) 75 Ohm termination
Picture-in-Picture
Video 1, Video 2, S-video
Bosch Security Systems, Inc.
Instruction Manual
F01U076723 | 1.0 | 2007.09
30
en | Technical Specifications
UML-202-90
HDMI/DVI/RGB Inputs
Analog RGB
0.7 Vp-p (0.5-1 Vrms)
Picture-in-Picture
Video 1, Video 2, S-video
DVI/RGB/HDMI Timing Modes
640 x 480, 60/72/75 Hz
800 x 600, 60/72/75 Hz
1024 x 768, 60/70/75 Hz
1280 x 1024, 60/75 Hz
1600 x 1200, 60 Hz
Component Timing
Resolution
V-freq (Hz)
640 x 480 (480i)
60
HDMI Timing
720 x 576 (576i)
50
640 x 480 (480P)
60
720 x 576 (576P)
50
1280 x 720 (720P)
50, 60
1920 x 1080 (1080i)
50, 60
1920 x 1080 (1080P)
50, 60
Resolution
V-freq (Hz)
640 x 480 (480P)
60
720 x 576 (576P)
50
1280 x 720 (720P)
50, 60
1920 x 1080 (1080i)
50, 60
1920 x 1080 (1080P)
50, 60
Audio Input
1.0 V line level, mono
Audio Output
Loop-through line level Speaker: two (2), 2 W
Controls
Front Panel
Push-buttons
Input
Selects Video 1, Video 2, S-video, RGB, DVI, or HDMI input
Menu
Selects on-screen display (OSD)
Up arrow, Menu select
Down arrow, Menu select
Left arrow, decrease
Right arrow, increase
Power
On/Off
Front Panel Lockout Multiple push-button combination
On-Screen Display
Video
Custom (Brightness, Contrast, Color, tint, Sharpness), Picture/Sound (Picture Mode, Color Tone,
Mute, Volume, Size, Auto Adjust, H-position, V-position, Frequency), PIP (PIP, Input Source, Size,
Position, Swap, Sound Select), Setup (Reset, Language, OSD Tone, Blue Screen, Key Lock,
Version)
DVI/RGB
Custom (Brightness, Contrast, Sharpness), Picture/Sound (Picture Mode, Color Tone, Mute,
Volume, PC, Auto Adjust, H-position, V-position, Frequency), PIP (PIP, Input Source, Size,
Position, Swap, Sound Select), Setup (Reset, Language, OSD Tone, Blue Screen, Key Lock,
Version)
Indicators
LED
Power On (green)
Power Off (red)
Standby\Sleep Mode (flashes red)
On-Screen
“No Signal” (Moving OSD)
F01U076723 | 1.0 | 2007.09
Instruction Manual
Bosch Security Systems, Inc.
UML-202-90
Technical Specifications | en
31
Connectors
Video 1
Composite video: two (2) BNC (1 in, 1 out)
Video 2
Composite video: two (2) BNC (1 in, 1 out)
Y/C (S-Video)
Two (2) mini-DIN, 4-pin (1 in, 1 out)
Component
Y, Pb, Pr
Audio
PC: one (1) 1/8 in. mini phono plug Video: four (4) RCA (2 in, 2 out)
DVI-D
HDMI
RGB
One (1) DVI to DVI cable included
One (1) cable not included
One (1) RGB to RGB cable included
Power Cord
Two (2) 3-wire with a grounded plug, 1.8 m (6 ft) long, one (1) with a European/
Continental plug type and one (1) with a U.S. plug type
Mechanical
Cabinet Material
Front: ABS plastic
Chassis: electrolytic galvanized iron
Finish
Charcoal black
Mount
Wall mounting compatible with standard bracket, 100 mm centers, M4 thread
Environmental
Operating Temp.
0°C to 40°C (32°F to 104°F)
Storage Temp.
-20°C to 60°C (-4°F to 140°F)
Humidity
10%-95%, non-condensing
Bosch Security Systems, Inc.
Instruction Manual
F01U076723 | 1.0 | 2007.09
Americas:
Bosch Security Systems
130 Perinton Parkway
Fairport, New York, 14450
USA
Phone
+1 800 289 0096
Fax
+1 585 223 9180
www.boschsecurity.us
Europe, Middle East, Asia:
Bosch Security Systems B.V.
Postbus 80002
5600 JB Eindhoven
Phone:
+31 40 2577 200
Fax:
+31 40 2577 202
nl.securitysystems@bosch.com
www.boschsecurity.nl
www.boschsecurity.com
© Bosch Security Systems, Inc., 2007; F01U076723 | 1.0 | 2007.09
www.boschsecurity.com
Asia-Pacific:
Bosch Security Systems Pte Ltd.
38C Jalan Pemimpin
Singapore 577180
Phone
+65 6319 3450
Fax
+65 63139 3499
www.boschsecurity.com