AWA T2102B User manual

Add to my manuals
37 Pages

advertisement

AWA T2102B User manual | Manualzz

深圳市安科讯实业有限公司

印刷要求:

颜色:黑色双面印刷

材质:80克书纸

尺寸:

130x180mm

装订方式: 骑马钉

料号: 2.01.011.0487

制作: 肖小燕

校对:

审核:

批准:

10" (26cm) Portable TV and Photo Frame

T2102B-User Manual

Should you encounter any problems, please contact the help line before you return this product back to the place of purchase.

Contact our Toll Free Warranty

Support Help Line

1300 366 144

Email: [email protected]

Visit our web site for FAQ’s or request for service

www.awa.com.au

Warning

Important Notes on Safety

Before you use this product, please read carefully the corresponding parts about the signs on the product you have bought and keep it properly for future reference.

This sign indicates that there

Warning

Electric shock, do not open

Note: In order to reduce electric shock, please do not take off the cover.

There is no component inside that users can maintain.

。 is dangerous high voltage inside, and it is dangerous to contact any component inside the product in any form.

This sign prompts you to pay

Please ask qualified maintenance personnel to conduct maintenance. attention to the attached important notes on the operation and maintenance of the product.

z The notches and holes inside the cabinet, on the back and at the bottom of the cabinet are designed to provide necessary ventilation. z In order to ensure the reliable operation of this television and to prevent it from getting overheated, do not stop or cover these notches and holes.

- Do not cover the notches and holes with cloth or other materials.

- Do not put this television on bed, sofa, carpet, or on the surface of other similar object, in order to avoid causing the blockage of the notches and holes.

- Do not put this television in a limited space, such as bookcase or embedded cupboard unless there is proper ventilation conduction.

- Do not put this television in a limited space, such as bookcase or embedded cupboard unless there is proper ventilation conduction.

-Please keep an interval of 10cm (4 inch) between this product and the wall.

-In the process of use, this television may get slightly hot, and this is the normal condition and does not indicate that any failure occurs to it. z Do not put this television near or above electric heater or heating plate, or a place with direct sunlight. z Do not put heat-generation articles such as candle, ashtray, incense, flammable materials or explosive materials near this product. z Do not place any container containing water on this television, which will lead to fire hazard or electric shock. z Do not expose this television in the rain or somewhere near water (such as somewhere near bathtub, water basin, water trough in a kitchen or laundry pool, damp basement, or near swimming pool). If this television gets wet accidentally, please immediately unplug the power adapter, turn off the power switch of this television, and then contact the authorized distributor of this television for help. When cleaning the television, please use dry and soft cloth that does not contain any volatile material. Before cleaning, please make sure to unplug the power adapter and turn off power switch of this television. z Do not overload socket on the wall, extended electric line or convenient socket, which will lead to fire hazard or electric shock. z The power adapter should be laid in a position where it will not be trodden or be extruded by objects above or near it, and special attention should be paid to the electric lines at plug, convenient socket and the television lead-out. z To better protect this television in thunder weather, unattended status or when it is unused for a long time, please remove the plug, and disconnect the antenna or the connection of the cable system. In this way, damage of the television in a thunder or when surge appears in power line can be prevented.

z Connect the power adapter to the front of AC socket. Please make sure that the output voltage of the AC socket complies with the input voltage of the power adapter of this television. z Do not insert any metal object into the holes of this television. Otherwise it may lead to the danger of electric shock or the damage of the television. z In order to avoid electric shock, do not contact the inside of this television. Only qualified technical personnel can open of the cover of this television. z Please make sure to insert the power adapter firmly into the socket. When disconnecting the power adapter connection, please make sure to hold the outer cover of the power adapter, and then unplug the power adapter from the socket. z If this television fails to operate normally, especially when it gives out abnormal sound or emits unusual odor, please immediately unplug the power adapter and turn off the power switch of this television, and then contact the authorized distributor or service center of this television. z If this television is to be left unused for a long time or you leave home (especially when a child, elder or a disabled person is left at home alone), make sure to unplug the power adapter from the socket and turn off the power switch. If the remote controller is to be left unused for a long time, please take out the batteries and put it in a cool and dry place. The accumulated dust may make the input end of the power adapter emit sparks and heat or age in insulation, thereby causing electric shock, creepage or fire hazard. z There are rechargeable batteries within the television. If the television is to be left unused for a long time, please make sure to conduct charge, discharge on the television once every three months. z Avoid dropping the remote controller. z When the television is moved to a warm environment from a low-temperature environment, in order for the dew within the television to fully volatilize and become dry, the television should be left unused for a period of time before powering on and turning it on.

We strongly recommend you to use the original power adapter of our company. z If the product is to be installed in an environment with much dust, high temperature or low temperature, high humidity and chemical materials, and in airport or railway station where the product is to be used 24 hours a day, please contact the authorized service center. Otherwise, the display may be seriously damaged, and the product may be seriously damaged. z Please do not allow any child to play with this product. z Please store the accessories in a place that children cannot get near or reach. z Please do not put the product in an unstable position, such as rolling frame, slant ground or position influenced by external vibrations. z Do not make the product fall or lashed. If this product is damaged, please disconnect the power adapter, turn off the power switch, and contact the service center.

z This television has a LCD; please do not press the screen at discretion to avoid causing screen breakage. z Refer to description provided by manufacturer: For color LCD screen, the defect of 0.01% of pixels is allowed, so please understand that when finding related phenomenon.. z The quality of the received image and sound of this product is related to the local signal and use environment. If the receiving performance is found to be not so ideal, an outdoor antenna is recommended. z This product is hot-swappable. However, it is suggested to power off this product before plugging/unplugging your memory card, to protect the memory card or other devices.

Precautions for Displaying Still Image

Static image may cause perpetual damage to the television screen. z Avoid displaying static image on LCD flat panel for over 2 hours as this may cause remnant shadow to the screen.

This remnant shadow is also called Screen burn.

To avoid this type of remnant image shadow, please lower the luminance and contrast of the screen when displaying still image.

When watching LCD TV program in 4:3 format, there may be traces left on brims of images displayed on the right and left sides and in the middle due to different light emissions.

The damage caused by the above-mentioned factors is out of the scope of warranty.

CONTENT

GENERAL INFORMATION ABOUT THE T2102B............................................................................................. 1

QUICK GUIDE ......................................................................................................................................................... 1

P

LUG IN YOUR

T2102B.......................................................................................................................................... 1

P

REPARING THE

R

EMOTE

C

ONTROL

...................................................................................................................... 1

1. PANELS................................................................................................................................................................. 2

1.1

F

RONT PANEL AND SIDE PANELS

...................................................................................................................... 2

1.2

F

RONT PANEL TOUCH KEYS DEFINITION

.......................................................................................................... 3

2. INTRODUCTION ................................................................................................................................................. 3

2.1

C

HECK LIST

...................................................................................................................................................... 3

2.2

A

BOUT TRANSMISSION

.................................................................................................................................... 4

2.3

A

BOUT THE PORTABLE RECEIVING ANTENNA AND ACCESSORIAL ANTENNA

.................................................. 4

2.4

C

ONNECTING THE

T2102B

TO THE

TV ........................................................................................................... 5

2.5

C

ONNECTING THE ACCESSORIAL ANTENNA AND THE EXTERNAL ANTENNA

................................................... 5

2.

6 I

NSTALLING

S

TAND

......................................................................................................................................... 5

3. REMOTE CONTROL........................................................................................................................................... 6

3.1

D

EFINITION

...................................................................................................................................................... 6

3.2

P

REPARING THE REMOTE CONTROL

................................................................................................................. 7

4. NAVIGATING WITH MENUS........................................................................................................................... 8

4.1

B

ASIC OPERATION METHODS OF

TV

SET

......................................................................................................... 8

4.2

D

IGITAL

TV

AND ANALOG

TV ........................................................................................................................ 8

4.2.1 Menu summarize..................................................................................................................................... 8

4.2.2 Menu definition ....................................................................................................................................... 8

4.2.3 Special Features at the DTV mode....................................................................................................... 16

4.3

A

UDIO AND VIDEO INPUT

............................................................................................................................... 16

4.4

C

ONNECT TO

PC ............................................................................................................................................ 17

4.5

M

ULTIMEDIA

................................................................................................................................................. 17

5. MAINTENANCE................................................................................................................................................ 20

5.1

H

ANDLING YOUR

T2102B ............................................................................................................................. 20

5.2

C

ONSIDERATIONS ABOUT THE SCREEN

.......................................................................................................... 20

5.3

C

LEANING RECOMMENDATIONS

.................................................................................................................... 21

5.4

C

ARE THE POWER SOURCE

............................................................................................................................. 21

5.5

C

ARE BATTERY

.............................................................................................................................................. 21

5.6

A

BOUT THE HEADPHONE USING

..................................................................................................................... 22

6. TROUBLESHOOTING ...................................................................................................................................... 22

7. TECHNICAL SPECIFICATIONS ..................................................................................................................... 24

GENERAL INFORMATION ABOUT THE T2102B

T2102B is a portable digital TV set; it can be used in a car or outdoor. Throughout this manual you will notice that everyday operation of your T2102B is based on a series of user friendly on-screen displays and menus. These menus will help you get the most from your

T2102B, guiding you through installation, channel selection, viewing and many other functions.

NOTICE

Using the buttons on the remote control can perform all functions. But using the buttons on the front panel can perform some of the functions.

This product support several types of memory cards such as SD/MMC/MS, since there are many memory card brands, it is recommended to test whether a card is compatible with this product. (Note; this product does not support illegal cards) If the card is inserted correctly and the startup picture is displayed but the card fails to read, it is recommended that you shut down and restart the unit or reformat the card before writing files onto it.

QUICK GUIDE

Plug in your T2102B

You can use either an AC adapter or a rechargeable Li-ion battery as a power source for your T2102B.

NOTICE

! only with the supplied AC adapter.

To use the AC adapter:

1.

Plug one end of the power cord into the AC outlet.

2.

Plug the cable attached to the AC adapter into the DC in port on the T2102B.

Preparing the Remote Control

Before using the remote controller, you need to insert the supplied battery in order to enable communication between the T2102B and remote controller. z To insert battery:

1

z Turn the remote controller over. z Press in the tab and lift the battery cover up. z Insert the supplied battery into the remote controller. z Align the battery cover to the remote controller. z Press down until the cover clicks into place.

OPEN

PUSH

! If the remote controller does not operate properly, you may need to replace the battery. When the remote controller is not being used for extended periods of time, remove the batteries to avoid possible damage from battery leakage

.

1. PANELS

1.1 Front panel and side panels

1.Screen

2. SD/MMC/MS CARD jack

3. USB jack

4. Power switch

2

5. Power supply jack

6. VGA input jack

7. Video input jack (CVBS)

8. Audio input jack (white port is left)

9. Audio input jack (red port is right)

10. Speaker

11. Portable receiving antenna (the antenna jack can plug the accessorial antenna)

12. Infrared remote receiver and Indicators (Red, Green)

The states are shown as:

Blue – Machine turn on, no charge

Red – Machine turn on and charge battery, Machine turn off and charge battery

Null – Machine turn off or charge battery full.

13. Stand

14. Headphone jack

15. Front panel touch keys (include

CH+, CH-

,

VOL+, VOL-, OK,

, and

MODE

)

1.2 Front panel touch keys definition

CH+:

Move up in the menus and change to the next channel in viewing mode.

CH-:

Move down in the menus and change to the previous channel in viewing mode.

VOL+

Move left /change settings in menus. Decrease the volume level in viewing mode.

VOL-:

Move right /change settings in menus. Increase the volume level in viewing mode.

OK:

To confirm a selection

: Press to open the menus /exit to go back to the topper menus.

MODE:

Open the mode main menu; press again to shift between

DTV, ATV, AV, VGA, and Multimedia.

! If you touch the front panel keys and the key show blue light color for a wait.

2. INTRODUCTION

2.1 Check list

The box for your T2102B should contain the following items:

3

z The T2102B machine z Owner’s manual z Remote control Headphone z Power supply adapter (AC adapter) Car Power Adapter z Accessorial Antenna

2.2 About transmission

Buildings, mountains and the surrounding terrain can block Radio and TV signals.

Depending on whether the receiver is located in a valley, behind a mountain or in a concrete building, the quality of reception may vary considerably. As with most other transmissions, bad weather affects reception quality. We recommend use the accessorial long antenna instead of short antenna when the signal isn’t good.

2.3 About the portable receiving antenna and accessorial antenna

z Use the antenna for UHF channels 21-69 for DVB-T, such as a directional antenna. z If possible, place the antenna by the window and directed towards the TV transmitter. z If possible, please use the power antennas. z The strength of TV signal varies according to reflections from buildings or mountains.

The signal penetrates thick stone or concrete walls poorly. However, a wooden building is not a big barrier to digital TV signals.

4

2.4 Connecting the T2102B to the TV

z Connect the T2102B AV input socket for video and audio. z Connect the T2102B Headphone jack to the TV audio input socket for sound.

2.5 Connecting the accessorial antenna and the external antenna.

Align the telescopic antenna plug with the antenna jack on the TV set, and just plug in until its end.

If you use the external antenna, unplug the telescopic antenna plug, plug the attached antenna plug into the antenna jack on TV set.

2. 6 Installing Stand

Insert the front end of the support to the slot on the back cover, and then rotate the base as illustrated in bottom, until the support is locked properly.

5

In order to storage remote control more expedient, insert the remote control to the slot on the back stand.

3. REMOTE CONTROL

3.1 Definition

This section describes how to operate the T2102B using the buttons on the remote control.

FAV

To operate the favorite channels (DVB and ATV

Function mode)

Mute

Press once to turn the sound off/on (mute/ unmute).

16:9/4:3

Screen switch. (DTV ATV and AV Function mode)

Mode

Press this button open the mode menu and press again to shift between Digital TV

Analogue TV

AV ,VGA and Multimedia.

AUTO

Start auto search (At Digital TV and Analogue TV mode)

Ok

To confirm a selection.

6

Or to open the channel list Menu. (At Digital TV and Analogue TV mode)

Menu /Exit

Press to open the menus and press again to go back to the topper menu.

Cursor up button,

move up in the menus and change to the next channel in viewing mode.

Cursor down button,

move down in the menus and change to the previous channel in viewing mode.

PIC

Press to open the picture mode menu.

Cursor left button,

move left /change settings in menus. Decrease the volume level in viewing mode.

Cursor right button,

move right /change settings in menus. Increase the volume level in viewing mode.

0~9

Press to change the channel and to select individual menu options.

LANG

Press to change the menu languages.

TTX

Press to enter Teletext (if available) (only Digital TV Mode)

INFO

Press to display the information of the current programs. (At Digital TV Mode)

S.TIT

Press to display the subtitle of the current programs. (only Digital TV Mode)

L/R

Press to change the sound channel (At Digital TV)

Or audio mode ( At ATV, AV and VGA mode).

EPG

Press this button to display Electronic Program Guide (only Digital TV Mode)

3.2 Preparing the remote control

Remove the cover from the battery compartment at the bottom of the remote control.

Insert the battery, taking care to observe the “+”and “–” markings indicated inside.

Replace the cover.

! Attention:

This remote controller’s figure maybe different to the remote controller what you obtained. But the symbols and functions on the remote controller are the same as this figure.

7

The remote control range is 4M or less within a±45°horizontal and ±5°vertical angle from the remote sensor. If the remote’s battery is low, the remote may not function properly, so replacing the battery immediately is recommended.

4. NAVIGATING WITH MENUS

4.1 Basic operation methods of TV set

1. Connect with power supply and turn on the power switch. In normal status, the power light is red. If you only use the battery power supply, the light is blue.

2. Pull out telescopic antenna.

3. Press

up/down

cursor buttons to choose the desired channel.

4. Press l

eft/right

cursor buttons adjust the sound volume of the TV

! Attention:

The following describes the functions of your T2102B while watching Analog

TV and terrestrial digital TV. Some of the functions described here are dependent on the

Service Provider and can only be used if they are included in the transmitted program information.

4.2 Digital TV and analog TV

4.2.1 Menu summarize

You can open the main menu by pressing

Menu

key at the remote control or front panel. You can perform different settings enter menus at current mode. And you can press mode key display mode menu, you can press

up/down

cursor buttons to select mode which you want with

OK

button enter.

Display menu by pressing the Menu button; press the menu button again to go back to the topper menu.

When menus are displayed, you can move the folders in horizontal directions with

left/right

cursor buttons.

4.2.2

Menu definition

The Main menu includes following menu icons:

8

, , , ,

,

To use the

up/down

cursor buttons

You can enter the submenu list by pressing

right

cursor.

Exit the menu list by pressing

Menu

.

.

:

You can select how the picture mode shall be sorted. There are four sort mode

(

personal, standard, dynamic

and

soft.

) are used here.

Figure 4.2.1

Brightness

Left/right

cursor buttons adjust the brightness of the screen.

Contrast

: adjust the contrast of the screen.

Color

: adjust the color of the screen.

Sharpness

: adjust the sharpness of the screen.

:

You can select how the audio mode shall be sorted. There are five sort mode (

personal, standard, music, movie

and

sports.

) are used here.

9

Figure 4.2.2

Bass

Left/right

cursor buttons adjust the bass of the screen.

Treble

: adjust the treble of the screen.

Balance

: adjust the balance of the screen.

Audio channel

:

Left/right

cursor buttons adjust the audio channel:

Stereo

,

L

and

R

Prefer Language

:

Left/right

cursor buttons adjust the prefer language:

English

,

German

,

Danish

and so on.

! Audio Channel

and

Prefer Language

menus only DTV mode and the program signal must contain.

:

You can select Country and the menu Language at the standard of local TV system..

In order to fit the person of different countries, the

menu language

can be set to different languages (

English, Dutch, French, German, Italian, Portuguese, and Spanish

) The default language is

English

.

Here, you can set

zoom mode

and other too.

10

Figure 4.2.3

Menu Language: Left/right

cursor buttons adjust the screen:

English, Dutch, French,

German, Italian, Portuguese, Spanish .

Zoom Mode: Left/right

cursor buttons adjust the screen:

16:9, 4:3

Battery Information: right

cursor buttons enter the battery information.

!

IF the Machine charge battery, the

Battery Information

menu can’t select.

Select Country: Left/right

cursor buttons adjust the screen:

Germany

,

French, Poland,

Portugal, Russia

and so on

Restore Default:

Press the

Left/right

cursor buttons to enter next step, and press

OK

key

to come back the factory default.

Antenna Power: Left/right

cursor buttons adjust the screen:

on, off

! Zoom Mode

only operated in

DTV, ATV

and

AV

mode.

If the machine turn on and used the outside power supplied or charge battery, the battery icon hide whenever on or off.

If use the power antenna, please press the

Left/right

cursor buttons to

ON.

: (Only DTV mode)

Under the Time Setting menu, you can set the time zone here in order to correct current time zone where you are.

11

Figure 4.2.4

! Clock setting

menu only

DTV

mode,

: (Only DTV mode)

To open this menu you will be asked to enter your access code. From the factory the access code is set to

0000

. After set, the access code has to be entered before you can watch locked channels and change the password.

:( Under the DTV mode)

Figure 4.2.5

12

Under the search menu, when you want to search for channels, a channel search procedure can be performed in different ways at

Automatic Search

and

Manual Search

. And you can edit favorite or skip channel lists in this menu.

If you edit channel favorite list ON, Press the

FAV

button can display the favorite List.

If you edit channel skip list ON, Press the CH+ or CH- don’t choose the channel.

DTV program:

press the

Left/right

cursor buttons adjust the screen:

DTV

or

RADIO

If you choose the D

TV

, current channel only the video program

If you choose the

RADIO

, current channel only the radio program

!if you current program is only the radio or video, and you want watch each other, please change the menu list.

Figure 4.2.6

Under the

Program Search

menu, Use

right

cursor button enter the submenu:

Figure 4.2.7

13

The TV list may contain a lot of channels. To sort your own lists you can make it easier to handle channels by LCN, number and name.

Under the DTV mode you can edit the personal channel list.

Press the

OK

button, open the channel list icon, then press the

right

cursor button again into the sub-menu ,so you can write a number what you want order, then ago order list be changed.

:( Under the ATV mode)

Figure 4.2.8

Figure 4.2.9

Program Search

menu under the ATV mode only add color system and sound system submenu.

Color System: Left/right

cursor buttons adjust the screen:

AUTO, PAL, SECAM

14

Sound System: Left/right

cursor buttons adjust the screen:

BG, DK, I, L

!

If the

Program List

menu does not exist . The system will automatically start the first time installation.

Press

OK

button to select

YES

;

Figure 4.2.10

Figure 4.2.11

Press

OK

button to select Country at the standard of local TV system .and Press

CH+/CH-

buttons to select other items. Set Language menu and

Time Zone

too.

!

The region item is decided by the signal of different country’s broadcasting companies.

15

4.2.3 Special Features at the DTV mode

Electronic Program Guide (EPG)

Pressing

EPG key

will open the EPG page. In the EPG you will find information about the programs for the current day and for the following seven days. (Provided that this information is included in the channel transmission from the distributor)

You may also select the type of program you want information about, like Movie, Sports or

Music.

TELETEXT

Pressing

TTX key

will open a TTX page, if TTX is transmitted for that channel. Select TTX pages using the

TTX

buttons on the remote control.

You can also quickly move to the different page options shown on any page by pressing

cursor left/right

.

Sometimes a TTX page may contain sub-pages. When sub-pages are available, they are numbered on the lower part of the screen. To view a sub page, press

OK

when no page numbers have been highlighted. Move to the different sub-pages with

cursor left/right

.

!

The program signal must contain

EPG

and

TTX

date.

4.3 Audio and video input

First just inset the plug of the external video cord into yellow jack, and left audio plug into the white port and right audio plug into the red port.

Press the

MODE

key to the AV mode, the screen display video play and music.

Figure 4.3.1

! Attention:

in the AV and VGA mode the operate menu have a little difference compare with DTV and ATV mode.

16

4.4 Connect to PC

Just inset the connect cord to the VGA port of PC, and tighten the screws to keep good contact, then plug the other end of the cord to the VGA port of the TV set and tighten the screws as the same.

Then turn the mode to VGA, the screen display as the monitor.

! Attention:

The VGA mode only support Standard is 640*480 60Hz and 800*600 60Hz.

Figure 4.4.1

4.5 Multimedia

! Attention:

Make sure the memory card into the right slot. If the card is improperly inserted, it may not function properly.

Press

Mode

key at the remote control or front panel, and Press

CH+/CH-

buttons to select

multimedia

, press

OK

button enter.

You can enter the icon by pressing

OK

key and pressing MENU key to go back to the topper

Menu interface.

Figure 4.5.1

17

When you select memory equipment display reading fulfil, you can enter the icon by pressing

OK

key.

Music:

At the function select interface, use the

VOL+/VOL-

to move the cursor to icon and press OK key enter.

Figure 4.5.2

In the music play interface, choose the file and press OK key playing. And press

VOL+

key to music control submenu. Press

menu

key to return main interface.

Figure 4.5.3

Photo:

At the function select interface, use the

VOL+/VOL-

to move the cursor to icon and press OK key enter.

Press

CH+/CH-

buttons to move the cursor to picture and press OK key enter, during the picture view mode, press

VOL+

key to photo control submenu. And then play the pictures which in current directory automatically.

18

Figure 4.5.4

Movie:

At the function select interface, use the

VOL+/VOL-

to move the cursor to icon and use the

CH+/CH-

to choose the file and press

OK

key playing.

In the video play interface, choose the file and press

OK

key playing. During movie playing,

Press

VOL+

key to video control submenu, and use the

VOL+/VOL-

to choose the preview or next file. And press

MENU

to return main interface.

During the movie playing, press

PIC

button, you can adjust the color, bright, and so on.

And press the

16:9/4:3

button you can change the movie size small screen or full screen.

!movie playing default is full screen.

Figure 4.5.5

19

5. MAINTENANCE

5.1 Handling your T2102B

1.

Do not drop the machine or heavy objects on top of the T2102B

2.

Do not place the machine in a location subject to: Heat sources, such as radiators or air ducts,

3.

Direct sunlight, Excessive dust, Moisture or rain, Mechanical vibration or shock, Strong magnets or speakers that are not magnetically shielded, Ambient temperature of more than 35

o

C or less than 5

o

C and High humidity.

4.

Do not place electronic equipment near the machine. The electromagnetic field of the machine may cause a malfunction.

5.

Provide adequate air circulation to prevent internal heat from building up. Do not place the machine on porous surfaces such as rugs or blankets, or near material such as curtains or draperies that may block its ventilation slots.

6.

The machine uses high-frequency radio signals and may cause interference to radio or

TV reception. If this occurs, relocate the machine a suitable distance away from the set.

7.

Use only specified peripheral equipment and interface cables; otherwise, problems may occur.

8.

Do not use cut or damaged connection cables.

9.

If the machine is brought directly from a cold location to a warm one, moisture may condense inside the machine, In this case, allow at least one hour before turning on the machine, if any problems occur, unplug the machine and contact an authorized Service

Centre. To find the nearest centre or agent, visit the online support Web site.

10.

Make sure you disconnect the power cord before cleaning the machine.

5.2 Considerations about the screen

1.

Please read the details of this guidebook before using, and store safely in case use another day.

2.

You may see tiny black points and/or bright points (red, blue, or green) that continuously appear on the LCD. LCD has a very few (0.01%) unlit pixels and always lit pixels. You may also see distortion in colours or brightness depending on your perspective. This is a normal result of the manufacturing process and does not indicate a malfunction.

3.

The LCD is manufactured using high-precision technology, do not apply a strong shock or drop it. Do not disassemble or refit yourself.

4.

Do not exert pressure on LCD screen. The LCD that is made from glass may be broken by pressure.

5.

Do not place your LCD in a location subject to direct sunlight or excessively high temperature. This may cause a malfunction.

6.

Do not place your LCD in a location subject to mechanical vibrations or in an unstable location.

20

7.

Do not place use a moist cloth to wipe the LCD. Liquid may cause a malfunction if it leaks into your LCD.

8.

Do not place or drop any object onto the LCD. Also, do not apply any force to the LCD.

If the liquid leaves out, please use soap and clean water to clean.

9.

If you bring your LCD from a cold location to a warm one, moisture may condense on the LCD. In such a case, wipe off the moisture before using your LCD. It is recommended to use tissue papers to wipe off the moisture. If the LCD surface is still not warm enough, moisture may condense again. Leave LCD until its surface is warmed up to the ambient temperature. Do not use alcohol, gas or chemistry reagent to wipe.

10.

Close LCD after use or during in malfunction. Please switch off power in case safe.

11.

If you have any questions, please contact our company.

5.3 Cleaning recommendations

1.

To clean the cover, take care the machine is disconnected.

2.

Do not use scented hydrocarbons or chloride solvents. Such products may attack the plastics used in the construction of the cover. The cover should be cleaned by means of a light solution of detergent and water applied with a soft cloth. Dry thoroughly before using the system again.

3.

Do not used for the cleaning of the front panel, alcohol or its derivatives, these products can attack the mechanical properties of the materials and diminish their useful time of life.

5.4 Care the power source

1.

Refer the online specifications to check the power operation of your machine.

2.

Do not share the AC outlet with other power-consuming equipment, such as a photocopier or shredder.

3.

You can purchase a power strip with a surge protector. This device prevents damage to the machine caused by sudden power surges, in an electrical storm.

4.

Do not place heavy objects on the power cord.

5.

To disconnect the cord, pull it out by the plug.

6.

Unplug the machine from the AC outlet if you are planning to not use the machine for a long time.

7.

Make sure that AC outlet is easily accessible.

8.

When the AC adapter is not used, unplug it from the AC outlet.

9.

Use the AC adapter supplied with the machine or authorized products. Do not use any other AC adapter as it may cause a malfunction.

5.5 Care battery

1.

Battery life is shorter in a cold environment. This is due to decreased battery efficiency at low temperatures.

21

2.

Charge the batteries at temperatures between 10

o

C to 30

o

C. Low temperatures require a long charging time.

3.

This machine is designed to operate only with special batteries. The battery design for only professional or Service Provider can open. Do not open or try to disassemble the battery cover on the back yourself.

4.

While the battery is in use or being charged, the battery pack heats up. This normal and is not cause concern.

5.

When the battery indicated iron on the screen flashes or when you have not used the battery for a long time, you need to recharge the battery.

6.

If the battery power is still low after charging it, the battery may be reaching the end of its life and should be replaced. Please contact your dealer or Service Provider.

5.6 About the headphone using

1.

Do not use headphones while driving, cycling, or operating any motorized vehicle. It may create a traffic hazard and is illegal in some areas. It can also be potentially dangerous to play loud music while walking, especially at pedestrian crossings.

2.

Avoid using headphones at high volume. Hearing experts advise and against continuous, loud and extended play. If you experience a ringing in your ears, reduce the volume or discontinue use.

6. TROUBLESHOOTING

Problem

The LED does not light up/is not lit.

Possible causes

Mains cable is not conn- ected.

The battery isn’t installed or need to recharge.

Condensed fluid may cause the machine

to malfunction.

What to do

Check that the mains cable is plugged into the power socket

Make sure the battery is installed properly and charged.

Reattach the AC adapter and reinstall the battery, and press the power button to turn on the machine.

Do not use the machine

for at least one hour if

22

The screen is close and Battery exhausted. power LED is on.

The remote control is not working.

Battery exhausted.

Don’t display the

subtitle

there are some condensed fluids in it.

Change battery.

Change battery.

Aim the remote control at incorrectly aimed Check that nothing blocks the front panel.

The program signal no Try press the S.TIT button

subtitle

date

The subtitle don’t open or open the subtitle.

Make sure the signal is

When the machine tries to signal too weak

The aerial is not properly connected to the machine. find and store channels you get the message “No mitter. signal” directed towards the trans-

When only very few of the

The aerial is not correctly

The aerial is not suitable for digital channels. expected number of channels are found. The signal is too weak for the connected aerial.

There are no terrestrial digital transmissions in the area.

Since the channel searching process use a lot of system resource, the system scan good

Check the aerial ins- tallation including its connections.

Check that the aerial is directed towards the trans- miters.

Check that digital trans- missions are available in the area.

If things does not work out as they should, let the local

TV dealer check whether the aerial is intended for receiving digital trans- missions or not. If not you have to exchange the aerial.

Try press buttons or remote controller’s keys several

During the channel searching process, the buttons or remote controller’s keys are insensitive.

Can’t play the music file correctly

Can’t play the video. become very slow.

The file is damaged or code is wrong

The format of the video doesn’t compatible or file has damaged.

Change the right files.

The max bit-rate of the video is 8Mbps.

23

Picture or video doesn’t full screen

The resolution of the files not suitable

Change the files

Note: If you have tried all of the actions suggested above, without solving the problem, please contact your dealer or Service Provider.

7. TECHNICAL SPECIFICATIONS

LCD

Panel

LCD Model Size

Active area

Resolution

RF input impedance

Digital television

RF input Frequency

RF input level range

Demodulation

Supported systems

Analogue television

RF input impedance

RF input Frequency

AV input

CVBS input level range

Supported CVBS systems

Supported VGA Format

VGA input

VGA input level range

Photo

Playback

Format

Max. resolution

Audio

Playback

File Format

10.1-inch Digital TFT LCD

219.6(W) ×131.76(H) mm

800*RGB x480

75 Ω imbalance

VHF High : 177.5MHz ~ 226.5MHz

UHF

474MHz

858MHz

20dBm

~-

78dBm

OFDM 2K and 8K, QPSK

16QAM, 64QAM

PAL - D/K 、 B/G 、 I 、

SECAM - D/K 、 B/G 、 L

75 Ω imbalance

VHF Low : 48.25MHz ~ 160.25MHz

VHF High

168.25MHz

456.25MHz

UHF : 464.25MHz ~ 863.25MHz

1.0Vp-p/75 Ω

PAL

NTSC

AUTO

640*480 60Hz

800*600 60Hz

H SYNC

3.3~5.0Vp-p

V SYNC

3.3~5.0Vp-p

RGB: 1Vp-p

JEPG(EXIF,JFIF

, baseline sequential DCT)

12 Mega-pixel

(Sample Rate 44.1kHz Bit Rate32k-320kbps)

24

Video

Playback

Coding Format

Memory

Support

Max. resolution

Bit rate

USB

SD/MMC/MS Card

Video

AVI (MPEG4 ASP (Level

5))

Audio

AUDIO

(MP2,AC3,PCM)

720 x 560

≤ 4Mbps(In Cards)

2.0

( only Host

Max. card capacity 2GB

Insert

Battery

Connect 3000Ma/h 7.4V

External power supply

input

Power consumption

100V

18W

240V±10%, 50~60Hz 0.55AMAX

DC power to the T2102B 9V 2A

Operating temperature 0°C to +40°C

Storage temperature

-20°C to +65°C

25% to 75% rel. humidity

Front panel

Dimensions (w×d×t)

Seven touch keys

286mm×178mm×39.5mm

Trademark Statement

The product names mentioned in this manual only serve for identification, and they may be the registered trademarks or copyright of other companies.The rest of the companies, products, or service names involved in this manual may all be the trademarks or service logos of the relevant holders here the following statement:

1.

SD logo is a registered trademark.

2.

Multi Media Card is the trademark of Infineon Technologies AG of Germany, and it has been authorized to Multi Media Card Association(MMCA)

3.

The rest of the companies, products, or service names involved in this manual may all be the trademarks or service logos of the relevant holders.

25

Company Statement

Our company hereby promises to users that the warranty period of our T2102B series products shall be valid within 12 months starting from the date of purchase (the warranty period of the batteries within the television shall be 6 months), and our company shall be responsible for providing free maintenance and repair for failures caused by non-human factors in normal use, and our company shall provide maintenance for failures exceeding the warranty period or caused by human factors, and shall charge the expenses of repair materials and related expenses.

Our company shall not bear any responsibility for any damage or loss resulting from failing to operate the television according to the operation manual.

Our company shall not bear any responsibility for any loss or claim for compensation caused by the use of this product by a third party.

The product specifications and information mentioned in this manual are for reference only, and the contents shall be subject to updating at any time without further notice.

26

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals