Canon iP6220D - PIXMA Color Inkjet Printer Service manual

PIXMA iP6220D
SERVICE
MANUAL
Canon
Copyright 2005, Canon U.S.A. This technical publication is the proprietary and confidential information of Canon U.S.A. which
shall be retained for reference purposes by Authorized Service Facilities of Canon U.S.A. Its unauthorized use is prohibited.
Scope
This manual has been issued by Canon Inc., to provide the service technicians of this product with the information
necessary for qualified persons to learn technical theory, installation, maintenance, and repair of products. The manual
covers information applicable in all regions where the product is sold. For this reason, it may contain information that is
not applicable to your region.
Revision
This manual could include technical inaccuracies or typographical errors due to improvements or changes made to the
product. When changes are made to the contents of the manual, Canon will release technical information when
necessary. When substantial changes are made to the contents of the manual, Canon will issue a revised edition.
The following do not apply if they do not conform to the laws and regulations of the region where the manual or product
is used:
Trademarks
Product and brand names appearing in this manual are registered trademarks or trademarks of the respective holders.
Copyright
All rights reserved. No parts of this manual may be reproduced in any form or by any means or translated into another
language without the written permission of Canon Inc., except in the case of internal business use.
Copyright © 2005 by Canon Inc.
CANON INC.
Inkjet Device Quality Assurance Div. 1
451, Tsukagoshi 3-chome, Saiwai-ku, Kawasaki-shi, Kanagawa 212-8530, Japan
I. MANUAL OUTLINE
This manual consists of the following three parts to provide information necessary to service the PIXMA iP6220D:
Part 1: Maintenance
Information on maintenance and troubleshooting of the PIXMA iP6220D
Part 2: Technical Reference
New technology and technical information such as FAQ's (Frequently Asked Questions) of the PIXMA iP6220D
Part 3: Appendix
Block diagrams and pin layouts of the PIXMA iP6220D
Reference:
This manual does not provide sufficient information for disassembly and reassembly procedures. Refer to the graphics in
the separate Parts Catalog.
II. TABLE OF CONTENTS
Part 1: MAINTENANCE
1. MAINTENANCE
1-1. Adjustment, Periodic Maintenance, Periodic Replacement Parts, and Replacement Consumables by
Service Engineer
1-2. Customer Maintenance
1-3. Product Life
1-4. Special Tools
1-5. Serial Number Location
2. LIST OF ERROR DISPLAY / INDICATIONS
2-1. Operator Call Errors
2-2. Service Call Errors
2-3. Warnings
2-4. Troubleshooting by Symptom
3. REPAIR
3-1. Notes on Service Part Replacement (and Disassembling / Reassembling)
3-2. Special Notes on Repair Servicing
3-3. Adjustment / Settings
(1) Paper feed motor adjustment
(2) Main chassis and carriage rail adjustment
(3) Grease application
(4) Waste ink counter setting
(5) User mode
(6) Service mode
3-4. Verification Items
(1) Service test print
(2) EEPROM information print
Part 2: TECHNICAL REFERENCE
1. NEW TECHNOLOGIES
2. CLEANING MODE AND AMOUNT OF INK PURGED
3. PRINT MODE
3-1. Resolution in Printing via Computer (Print on One or Both Sides of Paper, Photo and CL
Cartridges, Color Mode)
3-2. Resolution in Printing via Computer (Print on One or Both Sides of Paper, CL Cartridge, Color or
Monochrome Mode)
3-3. Resolution in Borderless Printing (Print on One or Both Sides of Paper, Photo and CL Cartridges,
Color Mode)
3-4. Resolution in Borderless Printing (Print on One or Both Sides of Paper, CL Cartridges, Color or
Monochrome Mode)
3-5. Resolution in Direct Printing
4. FAQ (Problems Specific to the iP6220D and Corrective Actions)
Part 3: APPENDIX
1. BLOCK DIAGRAM
2. CONNECTOR LOCATION AND PIN LAYOUT
2-1. Main Board
2-2. Operation Panel Board L
2-3. Operation Panel Board R
2-4. Card Slot Board (Card Slot Unit)
2-5. Carriage Board (Print Head Connector)
3. SPECIFICATIONS
Part 1
MAINTENANCE
1. MAINTENANCE
1-1. Adjustment, Periodic Maintenance, Periodic Replacement Parts, and
Replacement Consumables by Service Engineer
(1) Adjustment
Adjustment
Timing
Purpose
Tool
Approx.
time
EEPROM
initialization
(EEPROM
settings)
At logic board ass'y replacement To initialize settings other than
the following:
- USB serial number
- Destination setting
- Waste ink counter
None.
1 min.
Destination
settings
(EEPROM
settings)
At logic board ass'y replacement To set the destination.
None.
1 min.
LCD language
settings
At logic board ass'y replacement To set the language to be
displayed on the LCD.
None.
1 min.
Waste ink
counter
resetting
(EEPROM
settings)
- At bottom case unit
replacement
- At ink absorber replacement
To reset the waste ink counter.
None.
1 min.
Print head
alignment
- At printer setup
- At print head replacement
- At logic board ass'y
replacement
- At carriage unit replacement
To ensure accurate dot
placement.
- Machine buttons
(Auto/Manual)
- Computer
(settings via the
printer driver)
(Auto/Manual)
Auto:4
min.
Manual:3
min.
Paper feed
motor position
adjustment*1
At paper feed motor unit
replacement
To adjust the belt tension.
(Position the paper feed motor so
that the belt is stretched tight.)
None.
2 min.
Grease
application
- At carriage unit replacement
- At bottom case unit
replacement
- At platen replacement
- At eject roller replacement
- At cap blade unit replacement
-
- To maintain sliding properties
of the carriage, cap blade unit,
and eject rollers.
- FLOIL KG107A (QY90057)
- MOLYKOTE
PG641 (CK0562)
1 min.
*1: Red screws of paper feed motor
The red screws securing the paper feed motor may be loosened only at replacement of the paper feed motor unit.
(2) Periodic maintenance
No periodic maintenance is necessary.
(3) Periodic replacement parts
There are no parts in this machine that require periodic replacement by a service engineer.
(4) Replacement consumables
There are no consumables that require replacement by a service engineer.
1-1
1-2. Customer Maintenance
Adjustment
Timing
Purpose
Tool
- Machine buttons
(Auto/Manual)
- Computer (settings
via the printer
driver)
(Auto/Manual)
Approx.
time
Print head
alignment
When print quality is not
satisfying.
When printer is set up.
To ensure accurate dot
placement.
Print head
cleaning
When print quality is not
satisfying.
To improve nozzle conditions. - Machine button
- Computer (settings
via the MP driver)
1 min.
Print head deep
cleaning
When print quality is not
satisfying, and not improved by
print head cleaning.
To improve nozzle conditions. - Machine button
- Computer (settings
via the MP driver)
2 min.
Ink cartridge
replacement
When an ink cartridge becomes
empty. (No ink error)
-----
-----
Auto:4
min.
Manual:3
min.
2 min.
Paper feed roller When paper does not feed
properly.
cleaning
To clean the paper feed
rollers.
Machine button
2 min.
Bottom plate
cleaning
To clean the platen ribs.
- Machine button
- Computer (settings
via the MP driver)
1 min.
When the back side of the paper
is smeared
1-3. Product Life
(1) Machine
Specified print volume (I) or the years of use (II), whichever comes first.
(I) Print volume
6,600 pages
Black 1,500 character pattern
1,300 pages
Color A4, 7.5% duty per color pattern
1,000 pages
A4, 30 % duty per color pattern
1,000 pages
4 x 6, 30 % duty per color pattern
3,000pages
Postcard, 30 % duty per color pattern
300 pages
(II) Years of use
5 years of use
(2) Ink cartridge (ink tank with nozzles) (target value)
CL-52: 450 pages
710 pages
(1,500 character pattern / plain paper / standard mode)
(ISO JIS-SCID No. 5 / plain paper / standard mode)
CL-51: 330 pages
(ISO JIS-SCID No. 5 / plain paper / standard mode)
CL-52: 110 pages
(24 photos taken by a digital camera / borderless printing / SP101 4x6 / standard mode)
CL-51: 180 pages
(24 photos taken by a digital camera / borderless printing / SP101 4x6 / standard mode)
1-2
1-4. Special Tools
Name
Tool No.
Application
Remarks
MOLYKOTE
PG-641
QY9-0035-000 To be applied to the chassis.
In common with
other models.
FLOIL
KG-107A
QY9-0057-000 To be applied to the sliding portion of
the carriage, and the platen link.
In common with
other models.
1-5. Serial Number Location
On the chassis (visible when the front cover is open).
To the table of contents
To the top
<Part 1: 1.MAINTENANCE>
1-3
2. LIST OF ERROR DISPLAY / INDICATIONS
Errors and warnings are displayed by the following ways:
1) Operator call errors are indicated by the Alarm LED lit. (In the service mode, the Alarm LED blinks to indicate
errors.)
Service call errors are indicated by the number of cycles the Alarm and Power LEDs blink.
2) Errors and warnings are displayed on the LCD on the operation panel.
3) Warnings are displayed on the MP driver Status Monitor.
2-1. Operator Call Errors (by Alarm LED Lit in Orange)
LCD Message
Alarm LED
blinking in
orange (in the
service mode
only)
Error [Error code]
Solution
Remarks
There is no paper.
Load paper and press
[OK].
2 times
No paper. (ASF)
[1000]
Set the paper in the ASF,
and press the OK button.
The paper is jammed.
Clear the paper and
press [OK].
3 times
Paper jam. [1300]
Remove the jammed
paper, and press the OK
button.
No ink. [1600]
Replace the empty ink
Pressing the OK button will
cartridge(s), or press the exit the error without ink
OK button.
cartridge replacement,
however, ink may run out
during printing.
Ink has run out.
Replace the ink
cartridge and close
the cover.
U041
-
The following ink
cartridge cannot be
recognized.
U051 / U059
5 times
Ink cartridge not
installed. [1401]
Ink cartridge not for
this model installed.
[1485]
Confirm that the ink
cartridges are for this
model, install them
properly, then close the
front cover.
The following ink
cartridge cannot be
recognized.
U052
15 times
Ink cartridge not
installed. [1682]
Re-install the applicable
ink cartridge(s) properly,
and close the front cover.
Or, with the ink
cartridges installed, turn
the machine off and on
again.
The following ink
cartridge cannot be
recognized.
U140
-
Ink cartridge not for
this model installed.
[1684]
Confirm that the ink
cartridges are for this
model, install them
properly, then close the
front cover.
Some ink cartridge
are not installed in
place.
U075
7 times
Multiple ink cartridges Replace the wrong ink
of the same color
cartridge with the correct
installed. [1687]
one.
Some ink cartridge
are not installed in
place.
U076
7 times
Ink cartridge in a
Install the ink cartridge
wrong position. [1686] in the correct position.
The following ink
cartridge cannot be
recognized.
U053
4 times
Improper installation
of an ink cartridge.
[1687]
Re-install the applicable
ink cartridge(s) properly,
and close the front cover.
-
Warning: The waste
Pressing the OK button
The waste ink
1-4
The service call error,
absorber is almost
full.
Press [OK] to
continue but early
replacement
recommended. <See
manual>
ink absorber becomes
almost full.
[1700 for the main
waste ink absorber,
1710 for the platen
waste ink absorber]
will clear the error, and indicating the waste ink
enable printing.
absorber is full, is likely to
occur soon.
At repair*1:
For main waste ink
absorber replacement,
replace
- the bottom case unit, or
- the ink absorber kit
For platen ink absorber
replacement,
replace
- the ink absorber , and
- the ink absorber kit
MP450: QY5-0151).
Remove the cable
between the camera and
the machine, press the
Stop/Reset button, then
re-connect the cable.
Incompatible device
detected.
Remove the device.
-
The connected digital
camera or digital video
camera does not
support Camera Direct
Printing. [2001]
The following ink
may have run out.
U161
An ink cartridge that
was once empty is
installed.
U162
-
Remaining ink amount A once-used ink
unknown. [1685/1686] cartridge (except the one
which has been used
until just before
replacement) is installed.
Replace the applicable
ink cartridge with a new
one, or press the OK
button.
Auto head align has
failed. Press [OK] and
repeat operation.
<See manual>
-
Failed in automatic
print head alignment.
Press the OK button to
Press the Stop/Reset button.
exit the error, confirm
- If paper is being fed at
the following, then do
error occurrence, the error
the print head alignment
is indicated after the paper
again:
is ejected.
- If the error occurs, the print
- Set A4 or LTR size
head alignment values are
plain paper.
not changed.
- If the ink nozzles are
After
exit from the error by
clogged, cleaning the
the
Stop/Reset
button, the
ink cartridge.
automatic print head
- If the paper output slot
alignment will not be rehas been exposed to a
done.
strong light, move the
printer to a darker
location.
Cover is open.
-
Front cover open.
[1200]
Close the front cover.
Pressing the OK button will
exit the error without ink
cartridge replacement,
however, the function to
detect the remaining ink
amount is disabled.
*1: The main waste ink absorber is separate from the platen waste ink absorber. In servicing, replace the waste ink
absorber which becomes full.
[See Section 3-3. Adjustment / Settings, (6) Service mode, for details.]
1-5
2-2. Service Call Errors (by Cyclic Blinking in Orange (Alarm LED) and Green
(Power LED), or Alarm LED Lit in Orange)
Cycles of blinking in
orange (Alarm LED) and
green (Power LED)
Error [Error code]
Solution
(Replacement of listed parts, which are
likely to be faulty)
2 times
Carriage error [5100]
- Carriage unit (QM2-3332)
- Timing slit strip film (QC1-6015)
- Logic board ass'y (QM2-2840)*1
- Carriage motor (QM2-2865)
3 times
Paper feed error [6000]
- Timing sensor ass'y (QM2-2850)
- Timing slit disk film (QC1-4962)
- Feed roller ass'y (QL2-1284)
- Platen (QC1-7503)
- Logic board ass'y (QM2-2840)*1
- Paper feed motor (QM2-2866)
4 times
Purge unit error [5C00]
- Carriage unit (QM2-3332)
- Timing slit strip film (QC1-6015)
- Logic board ass'y (QM2-2840)*1
- Carriage motor (QM2-2865)
5 times
ASF (cam) sensor error [5700]
- Drive ass'y (QM2-3333)
- PE sensor ass'y (QM2-2855)
- Pressure roller ass'y (QM2-3337)
6 times
Internal temperature error [5400]
- Logic board ass'y (QM2-2840)*1
7 times
Waste ink absorber full [5B00]*2
Main waste ink absorber:
- Bottom case unit (QM2-3321)*3
- Ink absorber kit (QY5-0148)
Platen waste ink absorber:
- Ink absorber (QC1-6014)
- Ink absorber kit (QY5-0148)
8 times
Cartridge temperature rise error [5200]
- Print head
- Logic board ass'y (QM2-2840)*1
9 times
EEPROM error [6800]
- Logic board ass'y (QM2-2840)*1
13 times
Paper feed position error [6B00]
- Paper feed motor (QM2-2866)
- Logic board ass'y (QM2-2840)*1
15 times
USB Host VBUS overcurrent [9000]
- Logic board ass'y (QM2-2840)*1
17 times
Motor driver error [6D00]
- Logic board ass'y (QM2-2840)*1
20 times
Other hardware error [6500]
- Logic board ass'y (QM2-2840)*1
Continuous alternate
blinking
ROM error
- Logic board ass'y (QM2-2840)*1
Lights in orange
RAM error
- Logic board ass'y (QM2-2840)*1
*1: Before replacement of the logic board ass'y, check the waste ink amount, and re-set the waste ink amount value
in the replaced logic board.
[See Section 3-3. Adjustment / Settings, (6) Service mode, for details.]
*2: The main waste ink absorber is separate from the platen waste ink absorber. In servicing, replace the waste ink
absorber which becomes full.
[See Section 3-3. Adjustment / Settings, (6) Service mode, for details.]
*3: Reset the waste ink counter when replacing the bottom case unit. The main and platen waste ink counters can be
reset separately.
[See Section 3-3. Adjustment / Settings, (6) Service mode, for details.]
1-6
2-3. Warnings
Machine (displayed on the LCD):
Displayed warning
Remarks
Low ink
Print head temperature rise
If the print head temperature is high when the scanning unit is opened, the
warning is displayed.*1
When the print head temperature falls, the warning is released.
Protection of excess rise of the print head If the print head temperature exceeds the specified limit, a Wait is inserted
temperature
during printing,
*1: If the warning is displayed, the carriage does not move to the ink cartridge replacement position when the
scanning unit is opened.
2-4. Troubleshooting by Symptom
Symptom
Solution
The power does not turn on.
The power turns off immediately
after power-on.
Replace the
- AC adapter, or
Strange noise.
Remove foreign material, or attach a
removed part if any.
Printing stops mid-way.
Replace the logic board ass'y*1.
Nothing is displayed on the LCD.
- Confirm the connection of the LCD,
operation panel, and the logic board
ass'y.
- Replace the
- LCD, or
- logic board ass'y.
A portion of the LCD is not
displayed.
- Perform the button and LCD test in
the service mode, and confirm that the
LCD is displayed without any
segments missing.
- Confirm the connection of the LCD,
operation panel, and the logic board
ass'y.
- Replace the
- LCD, or
- logic board ass'y.
Multiple sheets feed.
Replace the
- drive unit, or
- pressing plate ass'y.
Paper does not feed.
Remove foreign material, or replace the
- drive unit, or
- pressing plate ass'y.
Paper feeds at an angle.
Remove foreign material, or adjust the
paper guide, or replace the
- drive unit, or
- pressing plate ass'y.
No printing, or no color ejected.
Replace the
Faulty operation
Paper feed
problems
- logic board ass'y*1.
- ink cartridge*2,
- logic board ass'y*1,
1-7
Remarks
- drive unit, or
- cap blade unit.
Printing is faint, or white lines appear Remove and re-install the ink
on printouts even after print head
cartridges, or replace the
cleaning.
- ink cartridge*2,
Line(s) not included in the print data
- cap blade unit,
appears on printouts.
- purge unit, or
- logic board ass'y*1.
Unsatisfactory
print quality
Paper gets smeared.
Feed several sheets of paper,
perform bottom plate cleaning, or
clean the paper path with cotton swab or
cloth.
A part of a line is missing on
printouts.
Replace the ink cartridge(s)*2.
Color hue is incorrect.
Replace the ink cartridge*2, or
perform print head alignment.
Printing is incorrect.
Replace the logic board ass'y*1.
No ejection of black ink.
Replace the ink cartridge(s)*2.
Graphic or text is enlarged on
printouts.
When enlarged in the carriage
movement direction, clean grease or oil
off the timing slit strip film, or replace
the
- timing slit strip film,
- carriage unit, or
- logic board ass'y*1.
When enlarged in the paper feed
direction, clean grease or oil off the
timing slit disk film, or replace the
- timing slit disk film,
- timing sensor unit, or
- logic board ass'y*1.
*1: Before replacement of the logic board ass'y, check the waste ink amount, and re-set the waste ink amount value
on the replaced logic board.
[See Section 3-3. Adjustment / Settings, (6) Service mode, for details.]
*2: Replace the print head only after the print head deep cleaning is performed 2 times, and when the problem
persists.
To the top
To the table of contents
<Part 1: 2. LIST OF ERROR DISPLAY / INDICATION>
1-8
3. REPAIR
3-1. Notes on Service Part Replacement (and Disassembling / Reassembling)
Service part
Logic board ass'y
QM2-2840
Bottom case unit
QM2-3321
Notes on replacement*1
Adjustment / settings
- Before removal of the logic
board ass'y, remove the
power cord, and allow for
approx. 1 minute (for
discharge of capacitor's
accumulated charges), to
prevent damage to the logic
board ass'y.
- After replacement, reset the
waste ink amount data in the
replaced logic board ass'y.
[See 3-3. Adjustment /
Settings, (6) Service mode, for
details.]
After replacement:
1. Initialize the EEPROM.
2. Set the destination in the
EEPROM.
3. Set the LCD language.
[See 3-3. Adjustment /
Settings, (6) Service mode,
for details of 1 to 4.]
4. Perform the print head
alignment in the user
mode.
- EEPROM information
print
- Service test print
- Printing via parallel or
USB connection
- Direct printing from a
digital camera
- Direct printing from a
memory card
Main platen waste ink
absorber
After replacement:
1. Reset the main waste ink
counter.
[See 3-3. Adjustment /
Settings, (6) Service
mode.]
2. Adjust the head-to-paper
distance.
[See 3-3. Adjustment /
Settings, (6) Service
mode.]
- Service test print
- Printing on thick paper
Ink absorber
QY5-0148
Operation check
- Print Beam printing
Carriage unit
QM2-3332
The red screws on both sides At replacement:
- Printing on thick paper
of the main chassis securing
1. Apply grease to the sliding
the carriage shaft are allowed
portions.
to be loosened only when
[See 3-3. Adjustment /
replacing the carriage or
Settings, (3) Grease
removing the main chassis.
application.]
Before removing the screws,
2. Adjust the distance between
mark the original screw
the carriage shaft and the
position, and re-fasten them at
platen.
the original position.
[See 3-3. Adjustment /
Settings, (2) Main chassis
and carriage rail
adjustment.]
3. Perform the print head
alignment in the user
mode.
Paper feed motor unit
QM2-2866
- The red screws securing the At replacement:
paper feed motor are allowed 1. Adjust the paper feed
to be loosened. (DO NOT
motor.
loosen any other red screws.)
[See 3-3. Adjustment /
Settings, (1) Paper feed
motor adjustment.]
Timing slit strip film
QC1-6015
Timing slit disk film
- Upon contact with the film,
wipe the film with ethanol.
- Confirm no grease is on the
film. (Wipe off any grease
thoroughly with ethanol.)
QC1-4962
- Do not bend the film
After replacement:
1. Perform the print head
alignment in the user
mode.
1-9
- Service test print
*1: General notes:
- Make sure that the flexible cables and wires in the harness are in the proper position and connected correctly.
[See 3-2. Special Notes on Repair Servicing, (1) Flexible cable and harness wiring, connection, for details.]
- Do not drop the ferrite core, which may cause damage.
- Protect electrical parts from damage due to static electricity.
- Before removing a unit, after removing the power cord, allow the machine to sit for approx. 1 minute (for
capacitor discharging to protect the logic board ass'y from damages).
- Do not touch the timing slit strip film and timing slit disk film. No grease or abrasion is allowed.
- Protect the units from becoming soiled with ink.
- Protect the housing from scratches.
- Exercise caution with the red screws, as follows:
i. The red screws of the paper feed motor may be loosened only at replacement of the paper feed motor
unit (DO NOT loosen them in other cases).
ii. Except for carriage replacement, DO NOT loosen the red screws (which secures the carriage shaft
positioning) on both sides of the main chassis.
After replacement of the carriage, print on thick paper to confirm that the distance between the
carriage shaft and the platen is proper, and there is no contact of the ink cartridges to the paper.
If the ink cartridges contact the paper, adjust the carriage shaft, while referring to [3-3. Adjustment /
Settings, (2) Main chassis and carriage rail adjustment.]
To the table of contents
To the top
<Part 1: 3. REPAIR, 3-1>
1-10
3-2. Special Notes on Repair Servicing
(1) Flexible cable and harness wiring, connection
Be careful of wiring of the flexible cables and harness. Improper wiring or connection may cause breakage of a
line, leading to ignition or emission of smoke.
1-11
To the table of contents
To the top
<Part 1: 3. REPAIR, 3-2>
1-12
3-3. Adjustment / Settings
(1) Paper feed motor adjustment
Perform the following adjustments when the paper feed motor unit is replaced:
1) When removing the screws, mark the screw hole.
2) When installing the motor, position each screw to the mark, and fasten them.
3) After replacement, be sure to perform the service test print, and confirm that no strange noise or faulty print
operation (due to dislocation of the belt or gear, or out-of-phase motor, etc.) occurs.
Note: The red screws securing the paper feed motor may be loosened only at replacement of the paper feed motor
unit. DO NOT loosen them in other cases.
(2) Main chassis and carriage rail adjustment
[Carriage rail adjustment]
Perform the following adjustments when the carriage unit is replaced:
1) Before loosening the red screws, mark the boss position beside the screw.
2) In attaching the carriage rail, make sure that the boss fits into the hole and to the mark made in step 1), then
fasten the screws.
3) Be sure to perform the confirmation test detailed below; confirm that the print quality is proper and the ink
cartridges are not contacting the paper.
1-13
[Main chassis adjustment]
After installing the main chassis, be sure to perform the confirmation test detailed below; confirm that the print
quality is proper and the ink cartridges are not contacting the paper.
<Confirmation test>
Using Photo Paper Pro, and with the paper thickness lever set to the left position (normal position), print an image
and confirm that the print quality is proper, and the ink cartridges are free from contacting the paper.
If the print quality is not proper, or an ink cartridge contacts the paper, adjust the head-to-paper distance in the
following procedures:
Procedures for adjusting the head-to-paper distance:
i) At the bottom edge of the boss beside the red screw on each side of the chassis, put a mark to indicate the current
position. (See the step 1 of the carriage rail adjustment above.)
ii) Loosen the red screws, and adjust the head-to-paper distance.
- To prevent the ink cartridges from contacting the paper: Raise the carriage rail from the current position.
- To improve the print quality: Lower the carriage rail from the current position.
1-14
(3) Grease application
1-15
Part name
Chassis
Where to apply grease / oil
1 Entire contact surface of the
Grease / oil name
Grease / oil amount
FLOIL KG107A
100mg
2 Inside of the rail
FLOIL KG107A
420mg
3 Back of the rail
FLOIL KG107A
100mg
4 Bottom of the rail
FLOIL KG107A
1 drop
5 Carriage slider contact portion
(front side)
FLOIL KG107A
1 drop
Idler pulley
6 Sliding portion
MOLYKOTE PG-641
1 drop
Bottom case unit
7 Slider shaft sliding portion (bottom MOLYKOTE PG-641
case top)
1 drop x 4 locations
8 Slider shaft sliding portion (bottom MOLYKOTE PG-641
case top)
1 drop x 4 locations
9 Slider shaft sliding portion (bottom MOLYKOTE PG-641
case top)
1 drop x 4 locations
10 Platen link sliding portion
MOLYKOTE PG-641
1 drop
11 Eject roller sliding portion
MOLYKOTE PG-641
Half drop
12 Trigger arm (carriage sliding
portion)
MOLYKOTE PG-641
1 drop
13 Eject roller sliding portion
FLOIL KG107A
Half drop x 2
locations
carriage slider
Platen
Note: 1 drop = 9 to 18 mg
To the table of contents
To the top
<Part 1: 3. REPAIR, 3-3 (1) to (3)>
1-16
(4) Waste ink counter reset
After replacement of the logic board ass'y, reset the waste ink amount value to the replaced logic board. In
addition, according to the waste ink amount, replace the waste ink absorber (the bottom case unit or the ink
absorbers). The standard amount for waste ink absorber replacement is given in the table below.
<Main waste ink absorber>
Waste ink
amount*1
Bottom case unit or ink absorber kit replacement
- Bottom case unit: QM2-3321
- Ink absorber kit: QY5-0148
Less than 7%
Not required.
7% or more
Required.
<Platen waste ink absorber>
Waste ink amount*1
Ink absorber (QC1-6014) replacement, and Ink absorber kit (QY5-0149)
replacement
Less than 7%
Not required.
7% or more
Required.
*1: Check the waste ink amount by service test print or EEPROM information print.
[See 3-3. Adjustment / Settings, (6) Service mode, for details.]
(5) User mode
Function
Procedures
Remarks
Nozzle check pattern
printing
On standalone machine, press the
Menu button, select
Maintenance/settings to move to
Maintenance, and perform the
selection.
Print head cleaning
Cleaning both black and color:
Also available from the printer driver
On standalone machine, press the Maintenance.
Menu button, select
Maintenance/settings to move to
Maintenance, and perform the
selection.
Print head deep cleaning
Cleaning both black and color:
Also available from the printer driver
On standalone machine, press the Maintenance.
Menu button, select
Maintenance/settings to move to
Maintenance, and perform the
selection.
Automatic print head
alignment
On standalone machine, press the
Menu button, select
Maintenance/settings to move to
Maintenance, and perform the
selection.
Also available from the printer driver
Maintenance.
Manual print head
alignment
On standalone machine, press the
Menu button, select
Maintenance/settings to move to
Maintenance, and perform the
selection.
Also available from the printer driver
Maintenance.
Print head alignment
value print
Print and confirm the print head
alignment values set in the
Also available from the printer driver
Maintenance. In the Maintenance tab,
1-17
Also available from the printer driver
Maintenance.
machine.
select Print Head Alignment and click
On standalone machine, press the Check Setting.
Menu button, select
Maintenance/settings to move to
Maintenance, and perform the
selection.
Paper feed roller cleaning On standalone machine, press the
Menu button, select
Maintenance/settings to move to
Maintenance, and perform the
selection.
Also available from the printer driver
Maintenance.
Bottom plate cleaning
On standalone machine, press the
Menu button, select
Maintenance/settings to move to
Maintenance, and perform the
selection.
Also available from the printer driver
Maintenance.
If the problem that smear is on the back
side of the paper is not resolved by Bottom
plate cleaning, clean the plate ribs.
Quiet mode setting
On standalone machine, press the Also available from the printer driver
Menu button, select
Maintenance.
Maintenance/settings, then Device
settings, and go to Print Settings,
then perform the selection.
Wireless print setting
Wireless print settings such as
paper type and print layout can be
made.
On standalone machine, press the
Menu button to move to
Maintenance / Settings, select
Device Settings, then perform the
selection.
Read/write attribute
setting
On standalone machine, press the
Menu button to move to
Maintenance / Settings; select
Device Settings, Other Settings,
and perform the selection.
Contrast adjustment
The contrast of the LCD can be
adjusted.
On standalone machine, press the
Menu button to move to
Maintenance / Settings, select
Device Settings, then Other
Settings, and perform the
selection.
Slide show setting
The slide show display quality can
be selected.
On standalone machine, press the
Menu button to move to
Maintenance / Settings; select
Device Settings, Other Settings,
and perform the selection.
Date display
On standalone machine, press the
Menu button to move to
Maintenance / Settings; select
Device Settings, Other Settings,
and perform the selection.
Language selection
The language to be used on the
LCD can be selected.
On standalone machine, press the
Menu button to move to
Maintenance / Settings, select
Device Settings, then perform the
1-18
selection.
Reset
Settings are reset to the original
shipping conditions.
On standalone machine, press the
Menu button to move to
Maintenance / Settings; select
Device Settings, then Reset
Setting.
Saving the settings
The current print settings are saved.
On standalone machine, press the
Menu button to move to
Maintenance / Settings; select
Device Settings, then Save
Settings.
Calling up the saved
settings
The saved print settings are called
up.
On standalone machine, press the
Menu button to move to
Maintenance / Settings; select
Device Settings, then Load
Settings.
Head-to-paper distance
setting
Move the paper thickness lever to
set the head-to-paper distance to
Auto or Wide.
(6) Service mode
Function
Procedures
Remarks
Service test print
- Model name
- ROM version
- USB serial number
- Waste ink amount
- Destination settings
See "Service mode operation
procedures" below.
Set a sheet of A4 or letter- sized paper.
For a print sample, see 3-4. Verification
Items, (1) Service test print, <Service test
print sample>.
EEPROM information
print
See "Service mode operation
procedures" below.
Set a sheet of A4 or letter- sized paper.
For a print sample, see 3-4. Verification
Items, (2) EEPROM information print
EEPROM initialization
See "Service mode operation
procedures" below.
The following items are NOT initialized:
- USB serial number
- Destination settings
- Waste ink counter
Waste ink counter reset
See "Service mode operation
procedures" below.
The main and platen waste ink counters
can be reset separately.
If the main waste ink amount is 7% or
more, replace the bottom case unit or the
main ink absorber (inside the bottom case
1-19
unit).
If the platen waste ink amount is 7% or
more, replace the platen ink absorber
(inside the bottom case unit).
Destination settings
See "Service mode operation
procedures" below.
After destination settings, make sure to
initialize the EEPROM.
Button and LCD test
See "Service mode operation
procedures" below.
Confirm the button and LCD operation.
Perform this test at operation panel
replacement.
Note: At the end of the service mode, press the Power button.
<Service mode operation procedures>
1) With the machine power turned off, while pressing the Stop/Reset button, press and hold the Power button. (DO
NOT release the buttons. The Power LED lights in green to indicate that a function is selectable.)
2) While holding the Power button, release the Stop/Reset button. (DO NOT release the Power button.)
3) While holding the Power button, press the Stop/Reset button 2 times, and then release both the Power and
Stop/Reset buttons. (Each time the Stop/Reset button is pressed, the Alarm and Power LEDs light alternately,
Alarm in orange and Power in green, starting with Alarm LED.)
4) When the Power LED lights in green, press the Stop/Reset button the specified number of time(s) according to
the function listed in the table below. (Each time the Stop/Reset button is pressed, the Alarm and Power LEDs
light alternately, Alarm in orange and Power in green, starting with Alarm LED.)
Time(s)
LED indication
0 times
Green (Power)
Power off
1 time
Orange (Alarm)
Service test print
See 3-4. Verification Items, (1) Service test
print.
2 times
Green (Power)
EEPROM information
print
See 3-4. Verification Items, (2) EEPROM
information print.
3 times
Orange (Alarm)
EEPROM initialization
4 times
Green (Power)
Waste ink counter
resetting
Proceed to the following step 5), and follow
the Waste ink counter reset procedures.
5 times
Orange (Alarm)
Destination settings
Proceed to the following step 5), and follow
the Destination settings procedures.
6 times
Green (Power)
Print head deep
cleaning
11 times
Orange (Alarm)
Button and LCD test
12 times or
more
Function
Remarks
Proceed to the following step 5), and follow
the Button and LCD test procedures.
Return to the menu
selection
5) After the function (menu) is selected, press the Power button. The Power LED lights in green, and the selected
function is performed. (When the operation completes, the machine returns to the menu selection mode
automatically.)
1-20
<Waste ink counter reset procedures>
In the waste ink counter resetting mode, press the Resume/Cancel button the specified number of time(s) according
to the ink counter reset value listed in the table below, and press the Power button.
Time(s)
LED indication
Waste ink counter value
0 times
Green (Power)
1 time
Orange (Alarm) Reset the platen waste ink counter (0%).
2 times
Green (Power)
Reset the main waste ink counter (0%).
Re-set the main waste ink counter value to 50%.
<Destination settings procedures>
In the destination settings mode, press the Stop/Reset button the specified number of time(s) according to the
destination listed in the table below, and press the Power button.
Time(s)
LED indication
Destination
0 times
Green (Power)
1 time
Orange (Alarm) Japan
2 times
Green (Power)
3 times
Orange (Alarm) USA
4 times
Green (Power)
5 times
Orange (Alarm) Australia
6 times
Green (Power) Asia
7 times
Orange (Alarm) China
8 times
Green (Power) Taiwan
Return to the menu selection
Korea
Europe
9 times or
Orange (Alarm) Return to the destination settings mode
more
Note: After setting the destination, be sure to initialize the EEPROM. The destination setting may not
be valid unless the EEPROM is initialized after destination settings.
Confirm the model name in the service test print or EEPROM information print.
[See 3-4. Verification Items, (1) Service test print, or (2) EEPROM information print.]
1-21
<Button and LCD test procedures>
In the button and LCD test mode, perform the following to confirm the operation of the buttons and the LCD.
1) Press the Stop/Reset button. The LCD color changes and displays a full blue screen.
2) Press each button on the operation panel (except the Power and Stop/Reset buttons). The color of a portion
corresponding to the pressed button changes to red.
For each portion of the display and its corresponding button, see the diagram below. (The diagram is a sample
when the down cursor and print buttons are pressed.)
=== LCD ===
3) When all the buttons excluding the Power and Stop/Reset buttons are pressed, the entire LCD changes to a full
red screen.
4) Open the front cover to display the color pattern.
5) Press the Power button to return to the service mode menu selection.
To the table of contents
To the top
<Part 1: 3. REPAIR, 3-3 (4) to (6)>
1-22
3-4. Verification Items
(1) Service test print
<EEPROM information contents>
On the service test print (sample below), confirm the EEPROM information as shown below. (The information is
given in the upper portion of the printout.)
iP6220D US
V.xxx
USB(xxxxxx)
Dd=xxx.x
iP6220D: Model name
US: Destination
V.xxx : ROM version
USB(xxxxxx): USB serial number
Dd=xxx.x: Main waste ink amount (%)
<Print check items>
On the service test print (sample below), confirm the following items:
- Check 1, nozzle check pattern: Ink shall be ejected from all nozzles
- Check 2, top of form accuracy: The line shall not extend off the paper.
- Check 3, vertical straight lines: The line shall not be broken.
<Service test print sample>
(2) EEPROM information print
<How to read the EEPROM information print>
Print sample:
1: iP6220D US 2: V1.03 3: IF(USB2=1) 4: D=004.5 Ds=0.002 5: ST=2005/07/27-18:30
6: ER(ER0=1000 ER1=0000) 7: LPT=2005/08/13-09:09
8: PC(M=002 R=000 T=001 D=009 C=009)
9: CLT(2005/08/10-18:30)
1-23
10: CT(Photo=001 CL_HC=002 CL_ST=000) 11: IS(PBK=0 C=0 PC=0 PM=0 M=0 Y=0)
12:: P_ON(S=00002) 13: A_REG=1 14: M_REG=0
15: UR(A(BKsi)=000 B(CLsi)=000 C(PBkbi)=000 D(SPBkbi)=000
E(Cbi)=000 F(SCbi)=000 G(BkCly)=000 H(Mbi)=000 I(SMbi)=000
J(PCbi)=000 K(SPCbi)=000 L(PMbi)=-01 M(SPMbi)=000 N(BkClx)=+06)
16: LG=01 Japanese 17: WP-0021 18: CDIN(LG-000 PB=000 OPB=000) 19: BTIN=0 20: MSD(002)
21: TPAGE=00140
22: PAGE(All=00001 PP=00001 HR+MP=00000 PR+SP+SG=00000 GP=00000 PC=00000 EV=00000)
23: CDPAGE(All=00000) 24: EDGE=00000 25: L=00000
26: Head Temp=43.0
27: Env Temp=27.5 28: FF(80 00 09) 29: OPP=00000 30: BTPAGE=00000 31: PrnB=00000 32: Seal=00000
33: CardPaper=00000 34: CardIns=(0001) 35: CardPrn=(0000)
36: CDD-PR(L=0002 2L=0000 PC=0000 A4=0000) 37: CDD-SP(L=0002 2L=0000 PC=0000 A4=0000)
38: CDD-MP(L=0002 2L=0000 PC=0000 A4=0000) 39: DCD-PR(L=0002 2L=0000 PC=0000 A4=0000)
40: DCD-FPP(L=0002 2L=0000 PC=0000 A4=0000) 41: DCD-MPP(L=0002 2L=0000 PC=0000 A4=0000)
Printed items:
1. Model name 2. ROM Version 3. Connected I/F (USB1) 4. Waste ink amount (D = Main, Ds = Platen) 5.
Installation date
6. Operator call/service call error record 7. Last printing time
8. Purging count
9. Cleaning time
10. Ink cartridge replacement count (standard BK, high-capacity BK, standard CL, high-capacity CL)
11. Ink status (BK/C/PC/PM/M/Y)
12. Power-on count (soft-on) 13. Automatic print head alignment 14. Manual print head alignment by user
15. User print head alignment value
16. Language destination 17. Wiping count 18. Camera Direct Print-supported device connection record (Bubble
Jet Direct, Canon PictBridge, Other maker's PictBridge)
19. Bluetooth-supported device connection record 20. Longest period of non-printing
21. Total pages fed
22. Pages fed (total, plain paper, High Resolution Paper & Matte Photo Paper, Photo Paper Pro & Photo Paper Plus
Glossy & Photo Paper Plus Semi-gloss, Glossy Photo Paper, Postcard, Envelope)
23. Camera Direct print pages (total) 24. Borderless print pages 25. L & 4x6 print pages
26. Print head temperature
27. Inside temperature 28. Line inspection information 29. Other photo paper print pages 30. Print pages via
Bluetooth connection
31. Print Beam print pages 32. Photo Stickers print pages
33. Business card & Credit card size paper print pages 34. Memory card use count 35.Card direct print pages
36. Number of Card Direct print: Photo Paper Pro (L/4x6, 2L/5x7, Japanese postcard, and A4/Letter)
37. Number of Card Direct print: Photo Paper Plus Glossy (L/4x6, 2L/5x7, Japanese postcard, and A4/Letter)
40. Number of Camera Direct print: Fast Photo Paper (L/4x6, 2L/5x7, Japanese postcard, and A4/Letter)
41. Number of Camera Direct print: Matte Photo Paper (L/4x6, 2L/5x7, Japanese postcard, and A4/Letter)
To the table of contents
To the top
<Part 1: 3. REPAIR, 3-4>
1-24
Part 2
TECHNICAL REFERENCE
1. NEW TECHNOLOGIES
(1) New Direct Print function
- Red eye correction: The red eyes area is selected from an image, and the red eyes are detected automatically.
Correction is made at the detected area.
- Memory card writing function: From the Menu, Setting of Read only (writing is not possible) and Read_Write
(writing is possible.) is possible.
<Possible problems with this function>
1) Print results is red-tinged. -> Change the correction value. (Shift to Y side.)
2) Direct Print is not possible. -> Release Write setting.
(2) Bluetooth printing support (option)
This printer has the Bluetooth printing function.
Install the optional Blurtooth unit (BU-20) in the printer.
<Possible problems with this function>
Printing is not possible. -> Shorten the communication distance or get rid of obstacles.
(3) Quiet mode
The machine has a quiet mode function.
Compared with the normal mode,
- Acoustic noise level: slightly lower. (HS normal approx. 42.7 dB, Quiet approx. 42.5 dB)
- Audible overtone level: Sound quality changes, and sound becomes quieter.
- Print speed: Slows.
<Possible problems with this function>
1) The operation sound does not become quieter.
=> The audible sound becomes only slightly quieter.
2) Printing is slow.
=> Disable the Quiet mode.
(4) Remaining ink level detection function
The machine has a function to detect the remaining ink level.
<Detection method>
- Dot counting (counted for each Photo / CL ink cartridge)
- The remaining ink level is detected by total counted dot values of 3 colors of ink.
<Display method>
- Displayed on the Status Monitor (at 4 levels listed below for each Photo / CL ink cartridge)
Level 1: Approx. 70% of ink remaining
Level 2: Approx. 40% of ink remaining
Level 3: Indication of "!" mark (Remaining ink level is low)
Level 4: Indication of "X" mark (No ink remaining)
Note: Remaining ink detection function displays the status only, and does not cause errors.
2-1
<Accuracy>
- The margin of error of detection accuracy is +/-10% in normal printing.
- The margin of error is likely to be large in the following specific print patterns:
When printing continuously using any one of the Photo /CL three colors of ink:
As the remaining ink level is calculated by the counted dot value of the least remaining ink of
Photo/Cl three colors, if any of the C/M/Y inks is heavily consumed, the margin of error for remaining
ink increases.
<Possible problems with this function>
1) When a one-used ink cartridge is installed, the actual remaining ink level is not detected, and an error indicating
the remaining ink amount is unknown occurs.
=> Pressing the OK button will clear the error, and printing can be done. However, the function to detect the
remaining ink amount is disabled (ink status i not displayed).
e.g. An ink cartridge was once used in another machine.
A current ink cartridge is removed from the machine. -> A new ink cartridge is installed. -> The removed
ink cartridge is installed again after removing the new ink cartridge.
2) Due to the specific print pattern, the actual remaining ink level does not match the indicated remaining ink level.
- This is because a detection error can be large in specific print patterns (such as continuous printing using any
one of the Photo/CL three colors of ink or continuous solid printing, etc.). (See "Accuracy" above.)
(5) Print head alignment
The machine has a print head alignment function to correct displacements between the nozzle lines of the print
head, and incorrect print position in bi-directional printing.
<Print head alignment>
A: Alignment of photo black nozzles in bi-directional printing
B: Alignment of cyan nozzles in bi-directional printing
C: Alignment of magenta nozzles in bi-directional printing
D: Alignment yellow nozzles in bi-directional printing
E: Alignment of photo black small nozzles in bi-directional printing
F: Alignment of cyan small nozzles in bi-directional printing
G: Alignment of magenta small nozzles in bi-directional printing
H: Alignment of yellow small nozzles in bi-directional printing
I: Alignment of photo cyan nozzles in bi-directional printing
J: Alignment of photo magenta nozzles in bi-directional printing
K: Alignment of photo cyan small nozzles in bi-directional printing
L: Alignment of photo magenta small nozzles in bi-directional printing
O: Horizontal alignment between chips
P: Vertical alignment between chips
W: Alignment of color nozzles small inclination
X: Alignment of black nozzles inclination
2-2
<Problems that can be resolved by this function>
Try the print head alignment for the following problems:
- The line is not straight.
- Printout is granulated.
<Possible problems with this function>
1) Print head alignment error
=> Perform print head deep cleaning (refreshing) because non-ejection of ink may occur.
(6) Print Beam printing
Wireless printing of photos from a camera-equipped mobile phone via infrared or Bluetooth communication is
available.
(Wireless printing from a computer or PDA is not available. Text cannot be wirelessly printed.
For Bluetooth communication, use the optional BU-20.)
<Supported mobile phones>
- Mobile phones with the IrDA port, supporting image data transfer via infrared communication
<Printable data>
- Photos taken with a camera-equipped mobile phone
<Restrictions>
- An image of 3.9 M or larger cannot be printed in some instances. Therefore, depending on a mobile phone
model, an image at the maximum resolution may not be printed.
- A moving image is not printed.
- Depending on a mobile phone model, data saved in its memory card is not printed.
- Downloaded contents or photos downloaded from a URL attached to a mail may not be printed.
<Possible problems with this function>
1) Print image quality is rough.
- The image resolution is automatically determined by the image size at shooting, thus printing on a large size
paper may result rough print quality.
=> Print on a small size paper, such as Business Card size, Credit Card size, or Photo Stickers.
2) Print orientation (portrait / landscape) cannot be specified.
- The print orientation is automatically determined by the image size at shooting.
=> Take a photo again in a desired orientation (portrait or landscape).
3) In borderless printing, the left and right side portions or the top and bottom portions extend off the paper.
- This is because the aspect ratio of a photo taken by a mobile-phone differs from that of paper.
=> Take a photo again, adjusting to position a shooting object in the center of the frame.
To the table of contents
To the top
<Part 2: 1. NEW TECHNOLOGIES>
2-3
2. CLEANING MODE AND AMOUNT OF INK PURGED
To prevent printing problems due to bubbles, dust, or ink clogging, print head cleaning is performed before the start of
printing, except in the following cases:
- Cleaning on arrival: Performed when the access cover is closed.
- Cleaning by dot count: Performed after ejection of paper (or after printing on the back side of paper when
auto duplex printing is performed).
- Manual cleaning / deep cleaning: Performed manually.
<Cleaning mode list>
Condition
Amount of ink used Est. required time
(g)
(sec.)
Details
Dot count cleaning
When the specified number of dots are
printed since the previous cleaning.
Photo: 0.10
CL: 0.10
40
Timer cleaning - 0
(First to third
cleaning after
shipping from the
plant.)
If 24 to 336 hours have elapsed since the
previous cleaning till the start of the next
printing.
Photo: 0.10
CL: 0.10
40
Timer cleaning - 1
If 336 to 1,440 hours have elapsed since
the previous cleaning till the start of the
next printing.
Photo: 0.10
CL: 0.10
40
Timer cleaning - 2
If 1,440 to 2,160 hours have elapsed since Photo: 0.15
the previous cleaning till the start of the
CL: 0.15
next printing.
40
Timer cleaning - 3
If more than 2,160 hours have elapsed
since the previous cleaning till the start of
the next printing.
Photo: 0.30
CL: 0.30
55
Photo: 0.15
Photo: 0.15
40
If the print head has
not been capped
before power-on
Ink cartridge
replaceme-1
Till 5,760 hours after the production date.
Photo: 0.10
CL: 0.10
40
Ink cartridge
replaceme-2
If more than 5,760 hours have elapsed
since the production date.
Photo: 0.20
CL: 0.20
45
Photo: 0.15
CL: 0.15
40
On arrival of the
machine
Manual cleaning
- Via the operation panel
- Via the MP driver
Photo: 0.10
CL: 0.10
40
Deep cleaning
- Via the operation panel
- Via the MP driver
Photo: 0.45
CL: 0.45
50
To the table of contents
To the top
<Part 2: 2. CLEANING MODE AND AMOUNT OF INK PURGED>
2-4
3. PRINT MODE
White background: Print with 5 pl only
Yellow background: Print with 5 pl and 2 pl
Green text: Fast
Blue text: Standard
Red text: High
3-1. Resolution in Printing via Computer (Print on One or Both Sides of Paper,
Photo and CL Cartridges, Color Mode)
Paper type
Plain paper
Quality level 5
Quality level 4
Quality level 3
Quality level 2
1 pass
1 pass
No. of
Bi-directional
Bi-directional
passes
Resolution Bk:300x300
Bk:300x300
(dpi)
Y,M,C:300x300 Y,M,C:300x300
3 passes
Bi-directional
Bk:600x600
Y,M,C:600x600
6 passes
Bi-directional
Bk:600x600
Y,M,C:600x600
Pm,Pc:600x600
Quality
level 1
6 passes
Bi-directional
Bk:600x600
High Resolution No. of
passes
Paper
Resolution
(dpi)
HR-101S
12 passes
Bi-directional
Bk:600x600
Y,M,C:600x600
Y,M,C:600x600
Pm,Pc:600x600
Pm,Pc:600x600
(print on one side) (print on one side)
No. of
Photo Paper Pro passes
Resolution
PR-101
(dpi)
16 passes
Biderection
6 passes
12 passes
Bk:
Bi-directional
Bi-directional
1200x1200
Bk:600x600
Bk:600x600
Y,M,C:
Y,M,C:600x600
Y,M,C:600x600 1200x1200
Pm,Pc:600x600
Pm,Pc:600x600
Pm,PC:
(print
on one side) 1200x1200
(print on one side)
(print on
one side)
Glossy Photo
Paper
GP-401
6 passes
Bi-directional
Bk:600x600
12 passes
Bi-directional
Bk:600x600
Y,M,C:600x600
Y,M,C:600x600
Pm,Pc:600x600
Pm,Pc:600x600
(print
on one side)
(print on one side)
No. of
passes
Resolution
(dpi)
6 passes
Bi-directional
Bk:600x600
12 passes
Bi-directional
Bk:600x600
Y,M,C:600x600
Y,M,C:600x600
Pm,Pc:600x600
Pm,Pc:600x600
(print
on one side)
(print on one side)
Photo Paper
Plus Glossy
No. of
passes
Photo Paper
Plus Semi-gloss Resolution
(dpi)
PP-101/SG-101
Matte Photo
Paper
MP-101
No. of
passes
Resolution
(dpi)
6 passes
Bi-directional
Bk:600x600
Y,M,C:600x600
2-5
12 passes
Bi-directional
Bk:600x600
Y,M,C:600x600
Pm,Pc:600x600
Pm,Pc:600x600
(print on one side) (print on one side)
3 pass
Envelope
T-shirt transfer
TR-301
Transparency
CF-102
Photo Paper
Plus Double
Sided
PP-101D
Other Photo
Paper
4 passes
Bi-directional
Bk:600x600
6 passes
Bi-directional
Bi-directional
Bk:600x600
Bk: 600x600
Y,M,C:600x600
Y,:M,C600x600
YMC: 600x600
Pm,Pc:600x600
Pm,Pc:600x600
(print on one
(print
on one side)
side)
(print on one side)
No. of
passes
Resolution
(dpi)
6 passes
Bi-directional
Bk:600x600
No. of
passes
Resolution
(dpi)
Y,M,C:600x600
(print on one side)
6 passes
Bi-directional
Bk:600x600
No. of
passes
Resolution
(dpi)
8 passes
Bi-directional
Bk: 600x600
Y,M,C:600x600 Y, M, C: 600x600
(print on one side) (print on one side)
6 passes
Bi-directional
Bk:600x600
No. of
passes
Resolution
(dpi)
Y,M,C:600x600
Pm,Pc:600x600
12 passes
Bi-directional
Bk:600x600
Y,M,C:600x600
Pm,Pc:600x600
12 passes
Bi-directional
Bk:600x600
Y,M,C:600x600
Pm,Pc:600x600
(print on one side)
No. of
passes
Resolution
(dpi)
3-2. Resolution in Printing via Computer (Print on One or Both Sides of Paper, CL
Cartridge, Color or Monochrome Mode)
Paper type
Quality level 5
Quality level 4
Quality level 3
Quality level 2
1 pass
Bi-directional
Y, M, C:
300x300
1 pass
Bi-directional
Y, M, C:
300x300
3 passes
Bi-directional
Y, M, C:
600x600
6 passes
Bi-directional
Y, M, C:
600x600
High Resolution No. of
passes
Paper
Resolution
(dpi)
HR-101S
6 passes
Bi-directional
Y, M, C:
600x600
(print on one
side)
12 passes
Bi-directional
Y, M, C:
600x600
(print on one
side)
No. of
Photo Paper Pro passes
Resolution
PR-101
(dpi)
6 passes
Bi-directional
Y, M, C:
600x600
(print on one
side)
12 passes
Bi-directional
Y, M, C:
600x600
(print on one
side)
Plain paper
No. of
passes
Resolution
(dpi)
2-6
Quality level 1
16 passes
Bi-directional
Y, M, C:
1,200x1,200
(print on one
side)
No. of
passes
Resolution
(dpi)
6 passes
Bi-directional
Y, M, C:
600x600
(print on one
side)
12 passes
Bi-directional
Y, M, C:
600x600
(print on one
side)
Photo Paper
Plus Glossy
No. of
passes
Photo Paper
Plus Semi-gloss Resolution
(dpi)
PP-101/SG-101
6 passes
Bi-directional
Y, M, C:
600x600
(print on one
side)
12 passes
Bi-directional
Y, M, C:
600x600
(print on one
side)
6 passes
Bi-directional
Y, M, C:
600x600
(print on one
side)
12 passes
Bi-directional
Y, M, C:
600x600
(print on one
side)
4 passes
Bi-directional
Y, M, C:
600x600
(print on one
side)
6 passes
Bi-directional
Y, M, C:
600x600
(print on one
side)
Glossy Photo
Paper
GP-401
Matte Photo
Paper
MP-101
No. of
passes
Resolution
(dpi)
3 passes
Envelope
T-shirt transfer
TR-301
Transparency
CF-102
Photo Paper
Plus Double
Sided
PP-101D
Other Photo
Paper
No. of
passes
Resolution
(dpi)
Bi-directional
Y, M, C:
600x600
(print on one
side)
No. of
passes
Resolution
(dpi)
6 passes
Bi-directional
Y, M, C:
600x600
(print on one
side)
No. of
passes
Resolution
(dpi)
6 passes
Bi-directional
Y, M, C:
600x600
(print on one
side)
8 passes
Bi-directional
Y, M, C:
600x600
(print on one
side)
No. of
passes
Resolution
(dpi)
6 passes
Bi-directional
Y, M, C:
600x600
12 passes
Bi-directional
Y, M, C:
600x600
12 passes
Bi-directional
Y, M, C:
600x600
(print on one
side)
No. of
passes
Resolution
(dpi)
2-7
3-3. Resolution in Borderless Printing (Print on One or Both Sides of Paper, Photo
and CL Cartridges, Color Mode)
Paper type
Plain paper
Photo Paper Pro
PR-101
Glossy Photo
Paper
GP-401
Quality level 5
Quality level 4
MP-101
Photo Paper
Plus Double
Sided
PP-101D
Other Photo
Paper
Quality level 2
Quality
level 1
3 passes
Bi-directional
Bk:600x600
No. of
passes
Resolution
(dpi)
Y,M,C:600x600
16 passes
Bidirectional
6 passes
12 passes
Bk:
Bi-directional
Bi-directional
1200x1200
Bk:600x600
Bk:600x600
Y,M,C:
Y,M,C:600x600
Y,M,C:600x600 1200x1200
Pm,Pc:600x600
Pm,Pc:600x600
Pm,PC:
(print
on one side) 1200x1200
(print on one side)
(print on
one side)
No. of
passes
Resolution
(dpi)
6 passes
Bi-directional
Bk:600x600
12 passes
Bi-directional
Bk:600x600
Y,M,C:600x600
Y,M,C:600x600
Pm,Pc:600x600
Pm,Pc:600x600
(print on one side) (print on one side)
No. of
passes
Resolution
(dpi)
6 passes
Bi-directional
Bk:600x600
12 passes
Bi-directional
Bk:600x600
Y,M,C:600x600
Y,M,C:600x600
Pm,Pc:600x600
Pm,Pc:600x600
(print
on one side)
(print on one side)
Photo Paper
Plus Glossy
No. of
passes
Photo Paper
Plus Semi-gloss Resolution
(dpi)
PP-101/SG-101
Matte Photo
Paper
Quality level 3
6 passes
Bi-directional
Bk:600x600
12 passes
Bi-directional
Bk:600x600
Y,M,C:600x600
Y,M,C:600x600
Pm,Pc:600x600
Pm,Pc:600x600
(print on one side) (print on one side)
No. of
passes
Resolution
(dpi)
6 passes
Bi-directional
Bk:600x600
No. of
passes
Resolution
(dpi)
12 passes
Bi-directional
Bk:600x600
Y,M,C:600x600
Y,M,C:600x600
Pm,Pc:600x600
Pm,Pc:600x600
(print on one side) (print on one side)
No. of
passes
Resolution
(dpi)
12 passes
Bi-directional
Bk:600x600
Y,M,C:600x600
Pm,Pc:600x600
(print on one side)
2-8
3-4. Resolution in Borderless Printing (Print on One or Both Sides of Paper, CL
Cartridges, Color or Monochrome Mode)
Paper type
Quality level 5
Quality level 4
Quality level 3
Quality level 2
Quality level 1
16 passes
Bi-directional
Y, M, C:
1,200x1,200
(print on one
side)
No. of
passes
Resolution
(dpi)
3 passes
Bi-directional
Y, M, C:
600x600
No. of
Photo Paper Pro passes
Resolution
PR-101
(dpi)
6 passes
Bi-directional
Y, M, C:
600x600
(print on one
side)
12 passes
Bi-directional
Y, M, C:
600x600
(print on one
side)
No. of
passes
Resolution
(dpi)
6 passes
Bi-directional
Y, M, C:
600x600
(print on one
side)
12 passes
Bi-directional
Y, M, C:
600x600
(print on one
side)
Photo Paper
Plus Glossy
No. of
passes
Photo Paper
Plus Semi-gloss Resolution
(dpi)
PP-101/SG-101
6 passes
Bi-directional
Y, M, C:
600x600
(print on one
side)
12 passes
Bi-directional
Y, M, C:
600x600
(print on one
side)
6 passes
Plain paper
Glossy Photo
Paper
GP-401
Matte Photo
Paper
MP-101
Photo Paper
Plus Double
Sided
PP-101D
Other Photo
Paper
No. of
passes
Resolution
(dpi)
Bi-directional
Y, M, C:
600x600
(print on one
side)
12 passes
Bi-directional
Y, M, C:
600x600
(print on one
side)
No. of
passes
Resolution
(dpi)
6 passes
Bi-directional
Y, M, C: 600x
600
12 passes
Bi-directional
Y, M, C: 600x
600
12 passes
Bi-directional
Y, M, C: 600x
600
(print on one
side)
No. of
passes
Resolution
(dpi)
2-9
3-5. Resolution in Direct Printing
Paper type
Plain paper
Photo Paper Pro
PR-101
Glossy Photo Paper
GP-401
Photo Paper Plus Glossy
Photo Paper Plus Semi-gloss
Standard
No. of passes
Resolution (dpi)
No. of passes
Resolution (dpi)
No. of passes
Resolution (dpi)
No. of passes
Resolution (dpi)
PP-101/SG-101
Matte Photo Paper
MP-101
No. of passes
Resolution (dpi)
6 passes
Bi-directional
Bk:300x300
High
12 passes
Bi-directional
Bk:300x300
Y,M,C:300x300
Y,M,C:300x300
Pm,Pc:300x300
Pm,Pc:300x300
(with borders only)
(with borders only)
+
6 passes
Bi-directional
Bk:600x600
Y,M,C:600x600
Pm,Pc:600x600
6 passes
Bi-directional
Bk:600x600
Y,M,C:600x600
Pm,Pc:600x600
6 passes
Bi-directional
Bk:600x600
Y,M,C:600x600
Pm,Pc:600x600
6 passes
Bi-directional
Bk:600x600
Y,M,C:600x600
Pm,Pc:600x600
12 passes
Bi-directional
Bk:600x600
Y,M,C:600x600
Pm,Pc:600x600
12 passes
Bi-directional
Bk:600x600
Y,M,C:600x600
Pm,Pc:600x600
12 passes
Bi-directional
Bk:600x600
Y,M,C:600x600
Pm,Pc:600x600
12 passes
Bi-directional
Bk:600x600
Y,M,C:600x600
Pm,Pc:600x600
To the top
To the table of contents
<Part 2: 3. PRINT MODE>
2-10
4. FAQ (Problems Specific to the iP6220D and Corrective Actions)
No. *
Function
Phenomenon
Carriage error
(LED cyclic
blinking in
orange and
green 2 times)
- During unpacking
and setup by a
user
- At ink cartridge
replacement
The user did not
install the ink
cartridges
completely.
Open the front
cover, and install
the ink cartridge(s)
properly.
An error occurs
indicating
incomplete
installation of an
ink cartridge.
Memory card In using a memory
not accessed or card which needs to
removed
be used with the
card adapter
The user inserted
the memory card
into the slot
without using the
card adapter.
- Use the card
- Printing cannot
adapter to insert
be done.
the memory card - The memory
into the slot.
card is not
- If the card cannot recognized.
be removed,
servicing is
required.
No paper
feeding
The paper feed
roller slips on the
paper at paper
feeding.
- Perform roller
- Paper out error
cleaning.
- Paper cannot
- Clean the paper
be fed
feed roller with - Cannot print
pre-moistened
wipe or
moistened cloth.
2
5
6
B
C
B
Possible call or
complaint
The LEDs blink
alternately in
orange and
green, 2 times
(carriage error).
Ink cartridge
installation
A Installation error
4
Corrective action
The user may not - Remove the
have removed the
packing material
packing material
fixing the
fixing the carriage. carriage.
Note: Even if the - Turn the
machine off, and
carriage
on again.
packing
material
remains, no
parts are
damaged.
A Installation
B Installation
Cause
During unpacking
and setup by a user
1
3
Condition
Paper
feeding
Multi-feeding
In the high
temperature and
high humidity
environment
The frictional force - Fan the paper
between the front
and set them in
and back sides of
the ASF.
paper becomes
- In case of PRhigh, and sheets
101, set the
stick to each other, paper sheet by
contributing to
sheet in the
multi-feeding.
ASF.
Envelope not
feeding
Envelopes
The paper feed
roller slips on the
paper at paper
feeding.
Note: Depending
on the
paper lots.
- Perform roller
- Paper out error
cleaning.
- Paper cannot
- Clean the paper
be fed
feed roller with - Cannot print
pre-moistened
wipe or
moistened cloth.
- Reduce the
number of
envelopes set in
the ASF.
- Flatten the
envelope (with a
pen).
Paper jam, or
Credit Card size
Due to paper
- Open the front
Paper
feeding
Paper
feeding
2-11
- Multiple sheets
of paper feed.
- Blank paper is
ejected.
- Paper jam error
7
8
9
10
11
B
B
B
C
C
improper paper paper
ejection
setting in the ASF covert, and
- Paper cannot
with the longer
remove the
be fed
side down, the LF
jammed paper. - Cannot print
roller cannot catch - Set a sheet of
the paper,
Credit Card size
preventing paper
paper in the ASF
feeding.
with the shorter
side down, and
press the
Stop/Reset
button.
Smearing on
printed side
The edge of paper - Correct the paper - Smear on the
rises due when
curl.
printed side of
paper is curled,
paper
- Set the paper
causing the ink
thickness lever - Cannot print
cartridge to rub
properly
for thick paper.
against the printed
- Recommend the - Paper edge
surface of paper.
user to print in
crease
the print quality
assurance area.
Smearing on
the backside, or
address side of
postcards
When borderless
- Perform Bottom
printing is
plate cleaning*1.
conducted
- Clean the ribs on
continuously, ink
the platen with
mist attaches to the
cotton swabs /
ribs on the platen,
buds*2.
and is transferred
to the backside of
the following
paper.
Horizontal
lines or uneven
print density at
the trailing
edge of paper
When the paper
- Recommend
- Cannot print to
end comes off the
printing in the
the bottom
pinch roller,
print quality
edge of paper
printing is
assurance area. - Line or uneven
performed without - Change the print
print density
the paper being
quality from
appear in the
held, preventing
Standard to High trailing edge of
the ink drops from
paper
mode.
being ejected in the
- Try other paper - Cannot print
correct positions,
(PP-101).
properly
resulting in
unevenness.
When printing
using one
cartridge only,
horizontal lines
or uneven print
density due to
LF roller
feeding at small
pitch
As the print media - Perform print
- Lines or
slightly slips while head alignment.
uneven print
being fed by the
density (on
- Change the print
LF roller, printed
skin tones and
quality from
areas overlap,
Standard to High background)
causing the
mode.
- Cannot print
problem.
properly
Paper
feeding
Image
quality
Image
quality
Image
quality
Image
quality
2-12
<Photo Paper
Plus Double
Sided>
- Smears on the
already printed
side when
printing the
other side
<When printing
the address side
of postcards>
- Smears on the
address side
<When printing
the message side
of postcards>
- Smears on the
backside
*1: When paper is not soiled, cleaning is complete. Change paper each time cleaning is performed.
*2: Locations to clean in servicing when soiling on paper in automatic duplex printing persists:
* Occurrence level:
A: The symptom is likely to occur frequently. (Caution required)
B: The symptom may occur under certain conditions, but likeliness is assumed very low in practical usage.
C: The symptom is unlikely to be recognized by the user, and no practical issues are assumed.
To the table of contents
To the top
<Part 2: 4. FAQ>
2-13
Part 3
APPENDIX
3. PIXMA iP6220D SPECIFICATIONS
<Machine>
Type
Desktop-type serial machine
Paper feeding method
Auto sheet feed (auto sheet feeder)
Resolution
4,800 x 1200 dpi (max.)
Throughput speed
(Target value)
Approx. 60 sec. (PP-101, 4x6, borderless printing, default print quality settings)
For reference:
Black
Color
Fast
11 ppm
9 ppm
Standard
3 ppm
2.6 ppm
Printing direction
Bi-directional / Uni-directional
Print width
203.2 mm (216 mm in borderless printing)
Interface
USB 2.0 Hi-Speed, Direct print port, IrDA 1.2 , Bluetooth 1.2
ASF stacking capacity
Max. 10 mm (Approx. 100 pages of 65 g/m2)
Paper weight
64 to 105 g/m2
Paper type (max.
stacking capacity)
Plain paper, 64 to 105 g/m2
A4, B5, LTR, A5 < 10 mm; LGL < 10 sheets
High Resolution Paper HR-101
A4, B5, LTR < 80 sheets
Glossy Photo Paper GP-401
A4, LTR < 10 sheets; 4x6, Credit Card < 20 sheets
Glossy Photo Paper GP-501
A4, LTR, 5x7 < 10 sheets; 4x6 < 20 sheets
Photo Paper Pro PR-101
A4, LTR < 10 sheets; 4x6, 4x8 < 20 sheets
Photo Paper Plus Glossy PP-101 A4, LTR, 5x7 < 10 sheets; 4x6 < 20 sheets
Photo Paper Plus Double Sided
PP-101D
A4, LTR, 5x7 < 1 sheet
Matte Photo Paper MP-101
A4, LTR < 10 sheets; 4x6 < 20 sheets
Photo Paper Plus Semi-gloss SGA4, LTR < 10 sheets; 4x6 < 20 sheets
101
Detection functions
Transparency CF-102
A4, LTR < 30 sheets
T-shirt transfer TR-301
A4 < 1 sheet
Envelope
COM#10, DL < 10 envelopes
Photo Stickers PS-101
1 sheet
- Front cover open
- Presence of print head
- Wrong installation of print head
- Remaining ink amount (dot count)
- Presence of memory card
- Paper presence
- Waste ink amount
- Internal temperature
- Carriage position
- Supported camera direct printing device
Acoustic noise level
(Highest print quality)
43 dB (Printing from a computer, highest print quality, Photo Paper Pro, Fine)
Environmental
requirements
During operation
Temperature
Humidity
3-11
5C to 35C (41F to 95F)
10% to 90%RH (no condensation)
Non-operation
Power supply
Temperature
Humidity
0C to 40C (32F to 104F)
5% to 95%RH (no condensation)
Power supply voltage,
Power
frequency
consumption
AC 100 to 240V, 50/60 Hz Approx. 11 W
Standby
Power-off
Approx. 1 W
Approx. 0.5 W
External dimensions
With the paper support and output tray retracted:Approx. 438 (W) x 260 (D) x 172 (H) mm
With the paper support and output tray extended:Approx. 438 (W) x 464 (D) x 318 (H) mm
Weight
Approx. 3.7 kg (excluding the ink cartridges)
Related standards
Electromagnetic radiance:
VCCI, FCC, IC, CE Mark, Taiwan EMC, C-Tick, CCC (EMC), Korea MIC, Gost-R
Electrical safety:
Electrical Appliance and Material Safety Law (DENAN), UL, C-UL, CB Report, CE
Mark, GS, Gost-R, FT, SASO, CCC, SPRING, Korea EK, IRAM (Argentine)
Serial No. location
Label affixed to the chassis (visible when the scanning unit is open)
Remaining ink detection Available (Detected by dot counting. Reset by user operation. Enabled at default.)
Paper type detection
Not available
Print head alignment
Available.
Automatic alignment, or manual alignment.
<Card Direct Printing>
Memory card drive Supported memory
card
Compact Flash TYPE I/II, Microdrive, SmartMedia Card, Memory Stick,
Memory Stick PRO, SD Card, MultiMedia Card, xD-Picture Card*,
miniSD memory card*, Memory Stick Duo*, Memory Stick PRO Duo*
Storage function
Operation
Via the machine buttons.
Condition
Before changing the settings, the memory card must be removed.
Function
Read/Write
Card Direct Printing File format
JPEG (DCF, CIFF, Exif 2.21 or prior, JFIF), Tiff, DPOF compliant
Supported print
paper
PR-101 (A4, LTR, 4x6)
PP-101 (A4, LTR, 5x7, 4x6)
SG-101 (A4, LTR, 4x6)
GP-401 (A4, LTR, 4x6, Credit Card)
MP-101 (A4, LTR, 4x6)
HR-101 (A4, LTR)
PS-101
Plain paper
Print quality
Standard (default), High
Image correction
function
Photo Optimizer PRO, VIVID, noise reduction, face brightener, image
optimizer, red eye correction
Image adjustment
function
Brightness, contrast, hue
Image processing
function
Sepia, illustrated touch, no processing
Image retrieval
function
Available (Date)
DPOF
Print layout
Ver. 1.00 compliant
Index printing, printing of an image the specified number of copies,
printing of the specified image(s), printing with the shooting date
Single-photo/multi-photo/all-photo printing:
1 photo per page (borderless/with borders, only with borders for plain
3-12
paper)
DPOF printing:
1 photo per page (borderless/with borders)
6, 15, 24, 35, 80 photos per page
30 photos per page (panorama)
Index printing:
6, 15, 24, 35, 80 photos per page
30 photos per page (panorama)
Layout printing:
2, 4, 8 photos per page (borderless/with borders)
Postcard (borderless/with borders, with/without lines)
Album (4 photos per page, right/left)
Mix 3 types (for A4/LTR)
Sticker printing:
2, 4, 9, 16 stickers
1, 5, 6, 7 stickers (for free-cut)
Information print
Date, file number
Throughput
Approx. 90 sec., with the following conditions and settings:
- A photo from a 5 mega-pixel digital camera
- PP-101 4 x 6 borderless
- Exif print
- Standard print quality
- Process from pressing the printing start button to ejecting paper
<Camera Direct Printing>
Supported digital
cameras
Digital cameras and digital video cameras supporting Bubble Jet Direct or PictBridge
Supported print paper
PR-101 (A4, LTR, 4x6)
PP-101 (A4, LTR, 5x7, 4x6, Panorama)
SG-101 (A4, LTR, 4x6)
GP-401 (A4, LTR, 4x6, Credit Card)
PS-101
Plain paper
Print layout
- 1 photo per page (borderless/with borders)
- Index printing
Resolution
1,200 x 1,200 dpi (max.)
Throughput
Approx. 89 sec., with the following conditions and settings:
- A photo from a 5 mega-pixel digital camera
- PP-101 4 x 6 borderless
- Exif print
- Standard print quality
- Process from pressing the printing start button to ejecting paper
<Print Beam printing>
Supported mobile phone Mobile phone equipped with IrDA 1.2 port, or with Bluetooth 1.2 port
Printable data
Supported print paper
Image (JPEG only, text printing not possible)
PR-101 (A4, LTR, 4x6)
3-13
PP-101 (A4, LTR, 5x7, 4x6, Panorama)
SG-101 (A4, LTR, 4x6)
GP-401 (A4, LTR, 4x6, Credit Card)
PS-101
Plain paper
Supported layout
1, 2, 4, 8 images per page (borderless/with borders)
3, 5, 6 images per page (A4 with borders)
1, 2, 4, 5, 6, 7, 9, 16 images per page (Photo Stickers with borders)
<Printing via Bluetooth communication (optional BU-20 required)>
Standard
Bluetooth version 1.2
Output
Bluetooth Power Class 2
Communication range
Good for approx. 10 m in radius (depending on interference between the communication
devices, or radio wave conditions)
Frequency band
2.4 GHz
Communication speed
Approx. 720 kbps
Supported profile
BIP, OPP, SPP, HCRP
Supported OS for HCRP - Windows XP Service Pack 2 or later
- Windows XP Service Pack 1 or later:
Microsoft "Support for Bluetooth Wireless Devices" or Toshiba Bluetooth Stack for
Windows Ver. 3.00.10 or later has to be installed
- Mac OS X 10.3.3 or later
BU-20 external
dimensions
18.5 (W) x 47.5 (D) x 8.7 (H) mm with a cap
BU-20 weight
Approx. 7 g
BU-20 power supply
voltage
4.4 to 5.25 V
BU-20 power
consumption
500 mW (max.)
BU-20 operating
temperature
5C to 35C (41F to 95F)
BU-20 operating
humidity
10% to 90%RH (no condensation)
<Ink cartridge>
Type
Ink-tank-integrated print head
Print head
Bk: 320 nozzles in 2 vertical lines
C/M/Y: 192 nozzles in 2 vertical lines per color
Ink color
Pigment-based black; Dye-based cyan, magenta, and yellow
Weight (net)
CL-41 approx. 45 g, CL-51 approx. 56 g, CL-52 approx. 56 g
Supply method
As a consumable
To the table of contents
To the top
<PIXMA iP6220D SPECIFICATIONS>
3-14