Motorola AP-6521 Series Installation guide

AP-6521E Access Point
INSTALLATION GUIDE
2
AP-6521E Access Point
MOTOROLA SOLUTIONS and the Stylized M Logo are registered in the US Patent & Trademark Office. © Motorola Solutions,
Inc. 2014. All rights reserved.
Installation Guide
1.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.1 Document Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.2 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.3 Site Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.4 AP-6521E Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
1.5 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.0 Hardware Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.1 Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.2 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.3 Access Point Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.3.1 Antenna Options. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.3.2 Power Injector System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
2.4 Wall Mount Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
2.5 Suspended Ceiling T-Bar Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2.6 Above the Ceiling (Plenum) Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
2.7 LED Indicator. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.0 Basic WiNG Express Access Point Configuration . . . . . . . . . . . . . . . . . . . . 19
4.0 Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
4.1 Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
4.2 Physical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
4.3 Radio Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
5.0 Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
5.1 Regulatory Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
5.2 Wireless Device Country Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
5.2.1 Country Selection - Note for AP & Wireless Controller. . . . . . . . . . . . . . . 31
5.2.2 Frequency of Operation - FCC and IC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
5.3 Health and Safety Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
5.3.1 Warnings for the use of Wireless Devices . . . . . . . . . . . . . . . . . . . . . . . . 32
5.3.2 Potentially Hazardous Atmospheres - Fixed Installations . . . . . . . . . . . . . 32
3
4
AP-6521E Access Point
5.3.3 Safety in Hospitals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
5.4 RF Exposure Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
5.4.1 Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
5.5 International . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
5.6 EU . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
5.7 US and Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
5.8 Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
5.9 Radio Frequency Interference Requirements - FCC . . . . . . . . . . . . . . . . . . . . . . 34
5.10 Radio Frequency Interference Requirements - Canada . . . . . . . . . . . . . . . . . . 34
5.4.1 Radio Transmitters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
5.11 CE Marking and European Economic Area (EEA) . . . . . . . . . . . . . . . . . . . . . . . 35
5.12 Mexico . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
5.13 Statement of Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
5.14 Waste Electrical and Electronic Equipment (WEEE). . . . . . . . . . . . . . . . . . . . . 36
5.15 Turkish WEEE Statement of Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
5.16 Japan (VCCI) - Voluntary Control Council for Interference Class B ITE . . . . . . 38
5.17 Korea Warning Statement for Class B ITE . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
5.18 Other Countries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
6.0 Motorola Solutions Support Center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Installation Guide
5
1 Introduction
AP-6521E Series Access Points are components of Motorola Solutions Wireless Controller System. An AP-6521E
links wireless 802.11a/b/g/n devices to the controller, enabling the growth of your wireless network with a
cost-effective alternative to standard Access Points. The AP-6521E Series Access Point is an enterprise class
802.11n Access Point, installed in minutes anywhere a CAT-5e (or better) cable is located.
An AP-6521E Series Access Point utilizes a setup wizard to define its operational mode as either a Dependent mode
AP, Standalone AP or Virtual Controller AP.
AP-6521E Series Access Points ship with a single dual-band radio supporting the 802.11a/b/g/n radio bands. For
more information on available SKUs, refer to the following:
Part Number
Description
AP-6521E-60010-US
802.11a/b/g/n single radio, integrated antenna, high power,
United States model, with WiNG Express
AP-6521E-60020-US
802.11a/b/g/n single radio, external antenna, high power,
United States model, with WiNG Express
AP-6521E-60010-EU
802.11a/b/g/n single radio, integrated antenna, high power,
European model, with WiNG Express
AP-6521E-60020-EU
802.11a/b/g/n single radio, external antenna, high power,
European model, with WiNG Express
AP-6521E-60010-WR
802.11a/b/g/n single radio, integrated antenna, high power,
World Wide model, with WiNG Express
AP-6521E-60020-WR
802.11a/b/g/n single radio, external antenna, high power,
World Wide model, with WiNG Express
The AP-6521E series Access Point is approved under MODEL: NCAP-500.
Motorola Solutions recommends the Access Point receive power and transfer data through the same CAT-5e (or
better) Ethernet cable using a Motorola Solutions Power Injector. The Power Injector
(Part No. AP-PSBIAS-2P2-AFR) is an 802.3af PoE injector. For information, see Power Injector System.
A separate power supply (Part No. PWRS-147376-01R) is also available if you do not wish to use a Power Injector.
This standard power supply just supplies power to the Access Point’s power connector and does not converge
power and Ethernet within a single cable connection.
6
AP-6521E Access Point
1.1 Document Conventions
The following graphical alerts are used in this document to indicate notable situations:
NOTE
!
Tips, hints, or special requirements that you should take note of.
CAUTION
Care is required. Disregarding a caution can result in data loss or
equipment malfunction.
WARNING! Indicates a condition or procedure that could result in personal injury or
equipment damage.
1.2 Warnings
•
•
•
•
Read all installation instructions and site survey reports, and verify correct equipment installation before
connecting the Access Point.
Remove jewelry and watches before installing this equipment.
Verify any device connected to this unit is properly wired and grounded.
Verify there is adequate ventilation around the device, and that ambient temperatures meet equipment
operation specifications.
1.3 Site Preparation
• Consult your site survey and network analysis reports to determine specific equipment placement, power
drops, and so on.
• Assign installation responsibility to the appropriate personnel.
• Identify and document where all installed components are located.
• Ensure adequate, dust-free ventilation to all installed equipment.
• Prepare Ethernet port connections.
• Verify cabling is within the maximum 100 meter allowable length.
1.4 AP-6521E Package Contents
An AP-6521E Access Point is available in integrated antenna and external antenna models. Contents differ
depending on the model ordered.
•
•
•
•
•
AP-6521E Access Point
AP-6521E Installation Guide (This Guide)
Rubber Wall Mount Spacers (4)
LED light pipe and badge
Wall mount screw and anchor kit
Installation Guide
7
1.5 Features
•
•
•
•
•
•
One RJ-45 console connector
LED indicators
Safety wire tie point
Wall mount slots
Clips for suspended T-Bar mounting
DC power connector
An AP-6521E Series Access Point has one RJ-45 connector supporting an 10/100/1000 Ethernet port connection
and requires 802.3af compliant power from an external source.
The Access Point contains runtime firmware which enables the unit to boot after either a power up or a watchdog
reset. The runtime firmware on the Access Point can be updated via the Ethernet interface.
8
AP-6521E Access Point
2
Hardware Installation
2.1 Installation Instructions
An AP-6521E Series Access Point can attach to a wall, mount under a suspended T-Bar or mount above a ceiling.
Select a mounting option based on the physical environment of the coverage area. Do not mount the Access Point
in a location that has not been approved in a site survey.
To prepare for the installation, perform the following:
1. Verify the contents of the box includes the intended Access Point and accessory hardware.
2. Review site survey and network analysis reports to determine the location and mounting position for the
Access Point.
3. Connect a CAT-5 or better Ethernet cable to a PoE compatible device and run the cable to the installation
site. Ensure there is sufficient cable slack to perform the installation steps.
4. Determine whether the Access Point is powered using a Power Injector system, combining data and
power to the Access Point’s GE1/PoE port or will be powered from a conventional power adapter
providing power only to the Access Point’s DC-48V connector.
2.2 Precautions
Before installing an AP-6521E model Access Point:
•
•
Verify the intended deployment location is not prone to moisture or dust.
Verify the environment has a continuous temperature range between 0° C to 40° C.
Installation Guide
9
2.3 Access Point Placement
For optimal performance, install the Access Point away from transformers, heavy-duty motors, fluorescent lights,
microwave ovens, refrigerators and other industrial equipment. Signal loss can occur when metal, concrete, walls
or floors block transmission. Install the Access Point in an open area or add Access Points as needed to improve
coverage.
Antenna coverage is analogous to lighting. Users might find an area lit from far away to be not bright enough. An
area lit sharply might minimize coverage and create dark areas. Uniform antenna placement in an area (like even
placement of a light bulb) provides even, efficient coverage.
Place the Access Point using the following guidelines:
•
•
•
Install the Access Point at an ideal height of 10 feet from the ground.
Orient the Access Point antennas vertically for best reception.
Point the Access Point antennas downward if attaching to the ceiling (external antenna models only).
To maximize the Access Point’s radio coverage area, Motorola Solutions recommends conducting a site survey to
define and document radio interference obstacles before installing the Access Point.
2.3.1 Antenna Options
Motorola Solutions supports two antenna suites for the single radio, dual-band AP-6521E Access Point. One
antenna suite supporting the 2.4 GHz band, and another antenna suite supporting the 5 GHz band. Select an
antenna best suited to the intended operational environment of your Access Point.
10
AP-6521E Access Point
The 2.4 GHz antenna suite includes the following models:
Part Number
Antenna Type
Approximate Gain (dBi)
ML-2452-APA2-01
Dipole
3
ML-2452-HPA5-036
Dipole
2.9
ML-2499-HPA3-01R
Dipole
4.6
ML-2499-APA2-01R
Dipole
2
ML-2452-APA2GA1-01
Dipole
2
ML-2452-PNA5-01R
Panel
4.5
ML-2452-PTA3M3-36
Patch
5
ML-2499-SD3-01R
Patch
4.8
Internal Antenna
PIFA
2.4
The 5 GHz antenna suite includes the following models:
Part Number
Antenna Type
Approximate Gain (dBi)
ML-2452-APA2-01
Dipole
5
ML-2452-HPA5-036
Dipole
4.9
ML-5299-APA1-01R
Dipole
2
ML-5299-HPA1-01R
Dipole
5
ML-2452-APA2GA1-01
Dipole
1
ML-2452-PNA5-01R
Panel
5
ML-2452-PTA3M3-36
Patch
3
ML-5299-PTA1-0R
Patch
5
Internal Antenna
PIFA
6
For a more exhaustive overview of the antennas and associated components supported by the Motorola Solutions
Access Point family, refer to the Enterprise Wireless LAN Antenna Specification Guide available at
https://portal.motorolasolutions.com/Support/US-EN/Wireless+Networks.
Installation Guide
11
2.3.2 Power Injector System
The Access Point can receive power via an Ethernet cable connected to the GE1/PoE port.
When users purchase a WLAN solution, they often need to place Access Points in obscure locations. In the past, a
dedicated power source was required for each Access Point in addition to the Ethernet infrastructure. This often
required an electrical contractor to install power drops at each Access Point location. The Power Injector merges
power and Ethernet into one cable, reducing the burden of installation and allowing optimal Access Point
placement in respect to the intended coverage area.
The Power Injector (Part No. AP-PSBIAS-2P2-AFR) is an 802.3af PoE injector. The Access Point can only use a Power
Injector when connecting to the Access Point’s GE1/PoE port. The Power Injector is separately ordered and not
shipped with the Access Point. A separate Power Injector is required for each Access Point comprising the network.
The Power Injector has no On/Off power switch. The Injector receives power and is ready for device connection and
operation as soon as AC power is applied. Refer to the Installation Guide shipped with the Power Injector for a
description of the device’s LEDs.The Power Injector can be installed free standing, on an even horizontal surface or
wall mounted using the Power Injector’s wall mounting key holes.
12
AP-6521E Access Point
The following guidelines should be adhered to before cabling the Power Injector to an Ethernet source and an
Access Point:
•
•
•
•
!
!
Do not block or cover airflow to the Power Injector.
Keep the Power Injector away from excessive heat, humidity, vibration and dust.
The Power Injector isn’t a repeater, and does not amplify the Ethernet signal. For optimal performance,
ensure the Power Injector is placed as close as possible to the Ethernet switch. This will allow the
AP-6521E to be deployed away from power drops.
Ensure the cable length from the Ethernet source (host) to the Power Injector and AP-6521E Access Point
does not exceed 100 meters (333 ft).
CAUTION
To avoid problematic performance and restarts, disable POE from a
wired controller port connected to an Access Point if mid-span power
sourcing equipment (PSE) is used between the two, regardless of the
manufacturer.
CAUTION
Ensure AC power is supplied to the Power Injector using an AC cable
with an appropriate ground connection approved for the country of
operation.
NOTE
If not using the Power Injector to power the Access Point, the only other
approved power solution is the standard power supply (Part Number
PWRS-147376-01R). The standard power supply does not converge data
and power in one cable, and requires a separate data Ethernet
connection in addition to a power connection. This product is intended to
be supplied by a listed power adapter marked “Class 2” or “L.P.S” (or
“Limited Power Source”) and rated from 48Vdc, 0.27A minimum.
Installation Guide
13
2.4 Wall Mount Installation
To support wall mount installations, the Access Point is fastened directly to a flat wall surface. The wall should be
of gypsum board, plaster, wood or concrete in composition.
!
CAUTION
An Access Point should be wall mounted to concrete or
plaster-wall-board (dry wall) only. Do not wall mount the Access Point
to combustible surfaces.
To install the Access Point to a wall surface:
1. Orient the Access Point by either its width or length.
2. Mark the mounting surface at the target screw insertion points.
3. At each point, drill a hole in the wall, insert an anchor, screw into the anchor the wall mounting screw and
stop when there is 1mm between the screw head and the wall.
4. If pre-drilling a hole, the recommended hole size is 2.8mm (0.11in.) if the screws are going directly into
the wall and 6mm (0.23in.) if wall anchors are being used.
5. If required, install and attach a security cable to the Access Point lock port.
6. Attach the antennas to their correct connectors.
For information on available antennas, see Antenna Options.
7. Place the large center opening of each of the mount slots over the screw heads.
8. Slide the Access Point down along the mounting surface to hang the mount slots on the screw heads.
9. Cable the Access Point using either the Power Injector solution or an approved line cord and power supply.
For Motorola Power Injector installations:
a. Connect an RJ-45 CAT5 Ethernet cable between the network data supply (host) and the Power
Injector’s Data In connector.
b. Connect an RJ-45 CAT5 Ethernet cable between the Power Injector’s Data & Power Out connector
and the Access Point.
c. Ensure the cable length from the Ethernet source (host) to the Power Injector and Access Point does
not exceed 100 meters (333 ft). The Power Injector has no On/Off power switch. The Power Injector
receives power as soon as AC power is applied. For more information, see Power Injector System.
For power adapter (Part Number PWRS-147376-01R) and line cord installations:
a. Connect a RJ-45 CAT5e (or CAT6) Ethernet cable between the network data supply (host) and the
Access Point’s GE1/PoE.
b. Verify the power adapter is correctly rated according the country of operation.
c. Connect the power supply line cord to the power adapter.
d. Attach the power adapter cable to the DC-48V power connector on the Access Point.
14
AP-6521E Access Point
e. Attach the power supply line cord to a power supply.
10. Verify the behavior of the Access Point LEDs. For more information, see LED Indicator.
11. The Access Point is ready to configure. For information on basic Access Point device configuration, see
Basic WiNG Express Access Point Configuration.
2.5 Suspended Ceiling T-Bar Installation
A suspended ceiling mount requires holding the Access Point up against the T-bar of a suspended ceiling grid and
twisting the Access Point chassis onto the T-bar.
To install the Access Point on a ceiling T-bar:
1.
2.
3.
4.
!
If desired, install and attach a security cable to the Access Point lock port.
If using an external antenna model, attach the antennas to their correct connectors.
For more information on the antenna options available to the Access Point, see Antenna Options.
Cable the Access Point using either the Power Injector solution or an approved line cord and power supply.
CAUTION
Do not connect to the power source until the cabling of the Access
Point is complete. Ensure PoE is not connected to the Access Point’s
console connector or risk rendering the console connector
permanently inoperable.
For Motorola Power Injector installations:
a. Connect an RJ-45 CAT5 Ethernet cable between the network data supply (host) and the Power
Injector’s Data In connector.
b. Connect an RJ-45 CAT5 Ethernet cable between the Power Injector’s Data & Power Out connector
and the Access Point.
c. Ensure the cable length from the Ethernet source (host) to the Power Injector and Access Point does
not exceed 100 meters (333 ft). The Power Injector has no On/Off power switch. The Power Injector
receives power as soon as AC power is applied. For more information, see Power Injector System.
For power adapter (Part Number PWRS-147376-01R) and line cord installations:
a. Connect a RJ-45 CAT5e (or CAT6) Ethernet cable between the network data supply (host) and the
Access Point’s GE1/PoE.
b. Verify the power adapter is correctly rated according the country of operation.
c. Connect the power supply line cord to the power adapter.
d. Attach the power adapter cable to the DC-48V power connector on the Access Point.
e. Attach the power supply line cord to a power supply.
5. Verify the behavior of the Access Point LEDs. For more information, see Basic WiNG Express Access
Point Configuration.
Installation Guide
6.
7.
8.
9.
15
Align the bottom of the ceiling T-bar with the back of the Access Point.
Orient the Access Point chassis by its length and the length of the ceiling T-bar.
Rotate the Access Point chassis 45 degrees clockwise.
Push the back of the Access Point chassis on to the bottom of the ceiling T-bar.
10. Rotate the Access Point chassis 45 degrees counter-clockwise. The clips click as they fasten to the T-bar.
11. Verify the behavior of the Access Point LEDs. For more information, see LED Indicator.
12. The Access Point is ready to configure. For information on basic Access Point device configuration, see
Basic WiNG Express Access Point Configuration.
16
AP-6521E Access Point
2.6 Above the Ceiling (Plenum) Installation
An above the ceiling installation requires placing the Access Point above a suspended ceiling and installing the
provided light pipe under the ceiling tile for viewing the status LED of the unit. An above the ceiling deployment
enables installations compliant with drop ceilings, suspended ceilings and industry standard tiles from .625 to .75
inches thick.
NOTE
!
The Access Point is Plenum rated to UL2043 and NEC1999 to support
above the ceiling installations. To ensure UL compliance and proper
Access Point operation within the Air Handling Plenum, the Access Point
must be installed with the bottom surface of the unit in contact with the
un-finished surface of the ceiling tile. Placing the product on the ceiling
tile will facilitate the positioning of the light pipe. Placement of the
product in the Air Handling Plenum off of, or away from, the unfinished
surface of the ceiling tile is not UL approved and certification of UL2043
compliance would be void in that case.
CAUTION
Motorola Solutions does not recommend mounting the Access Point
directly to suspended ceiling tile with a thickness less than 12.7mm
(0.5in.) or a suspended ceiling tile with an unsupported span greater
than 660mm (26in.).
The mounting hardware required to install the Access Point above a ceiling consists of:
• Light pipe
• Badge for light pipe
• Decal for badge
To install the Access Point above a ceiling:
1.
2.
3.
4.
5.
!
If possible, remove the adjacent ceiling tile from its frame and place it aside.
If required, install and attach a security cable to the Access Point’s lock port.
Mark a point on the finished side of the tile where the light pipe is to be located.
Create a light pipe path hole in the target position on the ceiling tile.
Use a drill to make a hole in the tile the approximate size of the Access Point LED light pipe.
CAUTION
Motorola Solutions recommends care be taken not to damage the
finished surface of the ceiling tile when creating the light pipe hole
and installing the light pipe.
6. Remove the light pipe’s rubber stopper (from the Access Point) before installing the light pipe.
7. Connect the light pipe to the bottom of the Access Point. Align the tabs and rotate approximately 90
degrees. Do not over tighten.
8. Fit the light pipe into hole in the tile from its unfinished side.
Installation Guide
17
9. Place the decal on the back of the badge and slide the badge onto the light pipe from the finished side of
the tile.
10. Attach the antennas to their correct connectors.
11. Align the ceiling tile into its former ceiling space.
12. Cable the Access Point using either the Power Injector solution or an approved line cord and power supply.
!
CAUTION
Do not connect to the power source until the cabling of the Access
Point is complete. Ensure PoE is not connected to the Access Point’s
console connector or risk rendering the console connector
permanently inoperable.
For Motorola Power Injector installations:
a. Connect an RJ-45 CAT5 Ethernet cable between the network data supply (host) and the Power
Injector’s Data In connector.
b. Connect an RJ-45 CAT5 Ethernet cable between the Power Injector’s Data & Power Out connector
and the Access Point.
c. Ensure the cable length from the Ethernet source (host) to the Power Injector and Access Point does
not exceed 100 meters (333 ft). The Power Injector has no On/Off power switch. The Power Injector
receives power as soon as AC power is applied. For more information, see Power Injector System.
For power adapter (Part Number PWRS-147376-01R) and line cord installations:
a. Connect a RJ-45 CAT5e (or CAT6) Ethernet cable between the network data supply (host) and the
Access Point’s GE1/PoE.
b. Verify the power adapter is correctly rated according the country of operation.
c. Connect the power supply line cord to the power adapter.
d. Attach the power adapter cable to the DC-48V power connector on the Access Point.
e. Attach the power supply line cord to a power supply.
13. Verify the behavior of the Access Point LED light pipe. For more information, see
LED Indicator.
14. Place the ceiling tile back in its frame and verify it is secure.
15. The Access Point is ready to configure. For information on basic Access Point device configuration, see
Basic WiNG Express Access Point Configuration.
18
AP-6521E Access Point
2.7 LED Indicator
An AP-6521E Access Point has a single LED activity indicator on the front of the unit.
The LED provides a status display indicating error conditions, transmission, and network activity for the 5 GHz
802.11a/n (amber) radio or the 2.4 GHz 802.11b/g/n (green) radio.
Task
5 GHz Activity LED (Amber)
2.4 GHz Activity LED (Green)
Unadopted
Off
Blinking 5 times per second
Normal
Operation
• If this radio band is enabled:
Blink at 5 second interval
• If this radio band is disabled:
Off
• If there is activity on this band:
Blink at a 1Hz
• If this radio band is enabled:
Blink at 5 second interval
• If this radio band is disabled:
Off
• If there is activity on this band:
Blink at a 1Hz
Firmware
Update
On
Off
Locate AP
Mode
Blink at 5Hz
Blink at 5Hz
Installation Guide
3
19
Basic WiNG Express Access Point Configuration
For a WiNG Express SKU (AP6521E), both the WiNG Express UI and an over the air (OTA) provisioning configuration
are required for a basic setup and network connection. For a non WiNG Express SKU (AP6521), there’s no OTA
support, and the Access Point utilizes just the UI for its basic setup.
NOTE For information on using WiNG Express beyond this initial setup, refer to
the Motorola Solutions WiNG Express Users Guide to familiarize yourself
with the WiNG Express Access Point operating system. The guide is
available at https://portal.motorolasolutions.com/Support/US-EN.
To provide the Access Point a basic configuration and access WiNG Express management functions:
1. Power up the Access Point.
The Access Point can be powered using an appropriately rated power adapter, POE injector or POE switch
resource.
2. Connect to the Access Point.
For WiNG Express models:
Connect to the WiNG Express SSID. For Windows systems, locate the SSID by selecting the network icon
on the bottom right corner of the screen. For MAC systems, locate the SSID by selecting the network icon
on the top right corner of the screen.
Open a browser (Chrome, Firefox or Internet Explorer) and enter
http://express.motorolasolutions.com. The login screen displays.
For non-WiNG Express models:
Refer to the bottom of the Access Point to obtain the numeric IP address used for connecting to the device.
Point the Web browser to the Access Point’s IP address. The login screen displays.
20
AP-6521E Access Point
3. Enter the default username admin in the Username field.
4. Enter the default password motorola in the Password field.
5. Select the Login button to load the management interface.
If this is the first time the WiNG Express interface has been accessed, a screen displays prompting for the
Access Point’s country code.
6. Select the Country Code specific to this Access Point’s deployment location.
Selecting the correct country is central to legal operation. Each country has its own regulatory restrictions
concerning electromagnetic emissions and the maximum RF signal strength that can be transmitted.
Select Apply to implement the selected Country Code. SKU's only support certain countries (for example:
a US SKU only includes US, Guam, Puerto Rico, American Samoa, US Virgin Islands and Mariana Island).
The Access Point automatically displays a Dashboard where users can assess network health and
conduct a diagnostic review of Access Point performance..
NOTE At some point in the Access Point’s initial setup, the default password
should be changed to enhance the security of the Access Point and WiNG
Express managed network. Refer to the Configuration > Management
screen to change the default password to a more secure password.
Installation Guide
21
7. Expand the Configuration menu item and select Basic.
8. Set the following Basic Configuration Settings for this Access Point:
• AP Name - Provide an AP Name used as this Access Point’s WiNG Express network identifier. If
setting this Access Point as a Virtual Controller, each Access Point managed by this Virtual Controller
lists this Access Point’s AP Name as its own. The AP Name is a required parameter.
• Country Code - If the Country Code was not set when the Access Point was initially powered on, set
the country now to ensure the Access Point’s legal operation. The Access Point’s wireless capabilities
are disabled until the required country code is set.
• Virtual Controller -Select this option to define this Access Point as a Virtual Controller capable of
managing and provisioning up to 24 Access Points of the same model. If selecting this Access Point
as a Virtual Controller, those Access Points managed by this Virtual Controller will list this Access
Point’s AP Name as its own. Only one Virtual Controller can be designated.
• Timezone - Use the drop-down menu to specify the geographic timezone where the Access Point is
deployed. Different geographic time zones have daylight savings clock adjustments, so specifying the
timezone correctly is important to account for geographic time changes.
• Date & Time - Set the date, hour and minute for the Access Point’s current system time. Specify
whether the current time is in the AM or PM.
• NTP Server - Optionally provide the IP address of a NTP server resource. Network Time Protocol (NTP)
manages time and/or network clock synchronization within the WiNG Express network. NTP is a
client/server implementation. Access Points (NTP clients) periodically synchronize their clock with a
master clock (an NTP server). For example, an Access Point resets its clock to 07:04:59 upon reading
a time of 07:04:59 from its designated NTP server.
9. Select Apply to implement the updates.
22
AP-6521E Access Point
10. Expand the Configuration menu item and select WAN.
11. Refer to the WAN Settings field and set the following:
•
Enable - Select this option to allow a connection between the Access Point and a larger network or
outside world through the WAN port. Disable this option to isolate the WAN connection. No
connections to a larger network or Internet are possible. Clients cannot communicate beyond
configured subnets. Both the physical Port used to connect to the WAN and the virtual Interface
(VLAN) are also listed and fixed.
•
DHCP Client - Select this option to enable DHCP for the Access Point WAN connection. This is
useful, if the target network or Internet Service Provider (ISP) uses DHCP. DHCP is a protocol that
includes mechanisms for IP address allocation and delivery of host-specific configuration
parameters from a DHCP server to a host. Some of these parameters are IP address, network mask,
and gateway. Motorola Solutions recommends the WAN and LAN ports should not both be
configured as DHCP clients.
•
Static IP - Select this option to bypass DHCP address allocation resources and manually set the IP
address for the Access Point’s WAN connection. Manually provide the Access Point’s Static IP/Mask
and Default Gateway.
•
PPPoE Settings - Optionally enable Point-to-Point Protocol over Ethernet (PPPoE) on the WAN
network. If PPPoE is enabled, provide the required Auth Type, Login Name and Login Password.
Server Name and Default Gateway are optional settings. PPP is a data-link protocol for dialup
connections allowing an Access Point to use a broadband modem (DSL, cable modem, etc.) for
access to high-speed data and broadband networks. Most DSL providers support (or deploy) the
PPPoE protocol. PPPoE uses standard encryption, authentication, and compression as specified by
the PPPoE protocol. PPPoE enables the Access Point to establish a point-to-point connection to an
ISP over an existing Ethernet interface.
Installation Guide
23
•
Static IP / Mask - Specify an IP address for the WAN connection if using static address assignment
for the WAN port. An IP address uses a series of four numbers expressed in dot notation, for
example, 190.188.12.1. Additionally, specify a Mask for the access point’s WAN connection. This
number is available from the ISP for a DSL or cable-modem connection, or from an administrator if
the Access Point connects to a larger network.
•
Primary/Secondary DNS/Default Gateway - If using a static IP or DHCP, enter the Primary and
Secondary DNS server resource’s numerical IP address and Default Gateway.
NOTE If segmenting traffic between the Access Point’s WAN and LAN, you’ll
need to create a VLAN. Complete steps 13 and 14 to define the required
VLAN. Otherwise, proceed to step 15.
12. Select Apply to implement the updates.
13. Expand the Configuration menu item and select Access Points. Each AP Name displays as a link that
can be selected to update the configuration of that specific Access Point. Select a target AP Name link
from amongst those displayed in the Access Points screen.
Refer to the LAN IP Interface Settings field, and add a VLAN and Static IP as required for enabling DHCP
(within the Configuration > Services screen) for client IP address requests and ensuring routable traffic.
24
AP-6521E Access Point
14. Select Apply to commit the updates to the selected Access Point’s configuration.
15. Expand the Configuration menu item and select Wireless.
The Wireless screen displays fields where Radio Settings and Wireless LAN settings can be defined.
Motorola Solutions recommends default radio settings remain as is for the Access Point’s basic setup. For
information on using WiNG Express beyond this initial setup, refer to the Motorola Solutions WiNG
Express Users Guide. The guide is available at https://portal.motorolasolutions.com/Support/US-EN.
In respect to the Radio Settings, the professional installer should be aware of the following:
NOTE The above example includes a field for setting the antenna gain. This
setting is only available for external antenna model Access Points and
does not display for internal antenna model Access Points.
•
The Channels available for configuration are channels for which the product is approved in its
selected country. The professional installer must ensure the product is set to operate under
conditions, and on channels, approved by country regulations.
•
Selecting Smart as the Power setting automatically configures radio power to not exceed the
maximum power allowed by the defined country. For static power settings, the professional installer
must ensure the configured power levels are compliant with local and regional regulations. The
county selected automatically limits the maximum output power that can be set.
•
For external antenna model Access Points, configure the Antenna Gain based on the antenna used
in the deployment. The set gain value should include the antenna gain, along with any additional
components, such as extension cables used between the Access Point and the antenna.
In respect to the Wireless LAN settings, the professional installer should be aware WiNG Express
Access Points ship with a default WLAN (WINGExpress). However, this WLAN does not provide adequate
authentication to protect from unauthorized user access. Motorola Solutions recommends an additional
WLAN configuration be created and validated before deleting default WLAN.
Installation Guide
25
16. To create a new WLAN, select + Add from the upper, left-hand side of the Wireless LAN field.
17. Set the following configuration attributes for the new WLAN:
•
Name - Provide a unique name for the WLAN as its WiNG Express network identifier. This is a
required setting.
•
Enable - Select this setting to enable this WLAN within the WiNG Express managed Access Point
network and to provide some measure of data protection not available in the default WLAN.
26
AP-6521E Access Point
•
SSID - Specify the WLAN's SSID. The WLAN SSID is case sensitive and alphanumeric. SSID length
should not exceed 32 characters. This is a required setting. Select Client-To-Client
Communication to enable client interoperability within this WLAN. The default is disabled,
meaning clients are not allowed to exchange packets with other clients. It does not necessarily
prevent clients on other WLANs from sending packets to this WLAN, but if this setting is disabled
on the other WLAN, clients are not permitted to interoperate at all.
•
WLAN Type - The screen displays with the Open option selected. Naming and saving such a policy
(as is) would provide no security and might only make sense in a network wherein no sensitive data
is either transmitted or received. This default setting is not recommended.
If selecting Secure-PSK, enter a WPA2 Key to password protect the WLAN. Define whether the
key is entered in ASCII or HEX characters. Selecting Show to expose the key is not recommended.
If selecting Secure-802.1x, provide an IP address (or hostname) and a shared secret (password)
used to access an external RADIUS server resource designated to validate user requests to the
Access Point’s WLAN resources.
Selecting Guest displays fields for captive portal Web page creation, and is beyond the scope of
this basic WiNG Express Access Point configuration.
•
Band -Select the 2.4 GHz and/or 5 GHz radio bands supports by the WiNG Express managed Access
Point and its connected client traffic. If this Access Point is designated as a Virtual Controller AP,
both radio bands should be enabled.
•
VLAN - Use the spinner control to specify a VLAN from 1 - 4,094 for this WLAN. When a client
associates with a WLAN, the client is assigned a VLAN by load balance distribution. Motorola
Solutions recommends you do not use VLAN 1 with the WLAN if the WAN port has been enabled.
•
Description - Optionally enter a WLAN description to further describe the WLAN’s deployment
objective within the WiNG Express managed network.
18. Select Apply to commit the updates to the Access Point’s WLAN configuration.
Installation Guide
27
19. Expand the Configuration menu item and select Services
.
20. Select Enable DHCP Server to ensure the Access Point can provision IP addresses to requesting clients
over the specified interface.
NOTE A VLAN must be already configured and available to the DHCP server as
a viable interface between the Access Point and requesting client. Refer
to the LAN IP Interface Settings field (within the Edit Access Point
screen), and add a VLAN.
Select + Add and provide a starting and ending IP range of addresses that constitute a pool of addresses
available to requesting clients.
21. Select Apply to commit the updates to the Access Point’s DHCP configuration.
22. At this point, you’re ready to connect to the WiNG Express managed network using the security
restrictions applied to the newly created WLAN. Ensure the new secure WLAN has been enabled, and
check whether a client is able to access the WiNG Express network.
NOTE Only when the new WLAN configuration is validated as accessible
should the existing WiNG Express default WLAN be deleted.
28
4
AP-6521E Access Point
Specifications
4.1 Electrical Characteristics
An AP-6521E model Access Point has the following electrical characteristics:
Max DC Power
Consumption
12.95W (270mA@48V)
4.2 Physical Characteristics
An AP-6521E model Access Point has the following physical characteristics:
Dimensions
6.0 (Length) x 5.5 (Width) x 1.63 (Tall) - Inches
152.4 (Length) x 139.7 (Width) x 41.1 (Tall) - Millimeters
Housing
Plastic
Weight
0.60 lbs/0.272 kg
Operating
Temperature
32°F to 104°F/0°C to 40°C
Storage Temperature
-40°F to 158°F/-40°C to 70°C
Operating Humidity
5 to 95% Relative Humidity non-condensing
Storage Humidity
85% Relative Humidity non-condensing
Operating Altitude
(max)
8,000 ft @ 28°C
Storage Altitude
(max)
30,000 ft @ 12°C
Electrostatic
Discharge
+/-15kV Air and +/-8kV Contact @ 50% Relative Humidity
Installation Guide
29
4.3 Radio Characteristics
An AP-6521E model Access Points have the following radio characteristics:
Operating Channel (2.4 GHz)
Channel 1 to 13 (2412 to 2472 MHz)
*Japan Only - Channel 14 (2484 MHz)
Operating Channel (5. GHz)
Channels 36 - 165
802.11a Data Rates
6, 9, 12, 18, 24, 36, 48, 54 Mbps
802.11b Data Rates
1, 2, 5.5, 11 Mbps
802.11g Data Rates
6, 9, 12, 18, 24, 36, 48, 54 Mbps
802.11n Data Rates
MCS0 to MCS15 at both HT20 and HT40 modes
Max Transmit Power (2.4GHz)
27 dBm
Max Transmit Power (5 GHz)
22 dBm
Transmit Power Adjustment
1 dB
NOTE
Channel 14 is valid only for 802.11b in Japan, 802.11g is not supported.
30
5
AP-6521E Access Point
Regulatory Information
5.1 Regulatory Overview
This device is approved under the Motorola brand.
This guide applies to Part Numbers AP-6521E-60010-US, AP-6521E-60020-US, AP-6521E-60010-EU,
AP-6521E-60020-EU, AP-6521E-60010-WR and AP-6521E-60020E-WR.
AP-6521 Series Access Points are approved under MODEL: NCAP-500.
All Motorola/Symbol devices are designed to be compliant with rules and regulations in locations they are sold and
will be labeled as required.
Local language translations are available at the following website:
https://portal.motorolasolutions.com/Support/US-EN/Wireless+Networks
Any changes or modifications to Motorola Solutions equipment, not expressly approved by Motorola Solutions,
could void the user’s authority to operate the equipment.
Motorola Solutions Access Points must be professionally installed and configured so that the Radio Frequency
Output Power will not exceed the maximum allowable limit for the country of operation.
Antennas: Use only the supplied or an approved replacement antenna. Unauthorized antennas, modifications, or
attachments could cause damage and may violate regulations. Use of an unapproved antenna is illegal under FCC
regulations subjecting the end user to fines and equipment seizure.
5.2 Wireless Device Country Approvals
Regulatory markings, subject to certification, are applied to the device signifying the radio(s) is/are approved for
use in the following countries: United States, Canada, Japan, China, S. Korea, Australia, and Europe.
Please refer to the Declaration of Conformity (DoC) for details of other country markings. This is available at
http://www.motorolasolutions.com/doc
Note: For 2.4GHz or 5GHz Products: Europe includes, Austria, Belgium, Bulgaria, Czech Republic, Cyprus, Denmark,
Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovak Republic, Slovenia, Spain, Sweden,
Switzerland and the United Kingdom.
Operation of the device without regulatory approval is illegal.
5.2.1 Country Selection – Note for AP & Wireless Controller
Select only the country in which you are using the device. Any other selection will make the operation of this device
illegal. The US version of the Access Point will only have US listed in the country selection table. The US version
will be sold / used in the US protectorates: American Samoa, Guam, Puerto Rico, US Virgin Islands.
Installation Guide
31
5.2.2 Frequency of Operation – FCC and IC
5 GHz Only
The use on UNII (Unlicensed National Information Infrastructure) Band 1 5150-5250 MHz is restricted to indoor use
only, any other use will make the operation of this device illegal.
Industry Canada Statement:
Caution: The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful
interference to co-Channel mobile satellite systems. High power radars are allocated as primary users (meaning
they have priority) of 5250-5350 MHz and 5650-5850 MHz and these radars could cause interference and/or
damage to LE-LAN devices.
Avertissement: Le dispositive fonctionnant dans la bande 5150-5250 MHz est réservé uniquement pour une
utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles
utilisant les mêmes canaux. Les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux
(c.-à-d., qu'ils ont la priorité) pour les bands 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer
du brouillage et/ou des dommages aux dispositifs LAN-EL.
2.4 GHz Only
The available channels for 802.11 b/g operation in the US are Channels 1 to 11. The range of channels is limited
by firmware.
5.3 Health and Safety Recommendations
5.3.1 Warnings for the use of Wireless Devices
Please observe all warning notices with regard to the usage of wireless devices.
5.3.2 Potentially Hazardous Atmospheres – Fixed Installations
You are reminded of the need to observe restrictions on the use of radio devices in fuel depots, chemical plants etc.
and areas where the air contains chemicals or particles (such as grain, dust, or metal powders).
5.3.3 Safety in Hospitals
Wireless devices transmit radio frequency energy and may affect medical electrical equipment. When
installed adjacent to other equipment, it is advised to verify that the adjacent equipment is not adversely
affected.
Pacemakers
Pacemaker manufacturers recommended that a minimum of 15cm (6 inches) be maintained between a handheld
wireless device and a pacemaker to avoid potential interference with the pacemaker. These recommendations are
consistent with independent research and recommendations by Wireless Technology Research.
32
AP-6521E Access Point
Persons with Pacemakers:
•
•
•
•
Should ALWAYS keep the device more than 15cm (6 inches) from their pacemaker when turned ON.
Should not carry the device in a breast pocket.
Should use the ear furthest from the pacemaker to minimize the potential for interference.
If you have any reason to suspect that interference is taking place, turn OFF your device.
Other Medical Devices
Please consult your physician or the manufacturer of the medical device, to determine if the operation of your
wireless product may interfere with the medical device.
5.4 RF Exposure Guidelines
5.4.1 Safety Information
Reducing RF Exposure—Use Properly
Only operate the device in accordance with the instructions supplied.
5.5 International
The device complies with internationally recognized standards covering human exposure to electromagnetic fields
from radio devices. For information on “International” human exposure to eletromagnic fields refer to the Motorola
Solutions Declaration of Conformity (DoC) at
http://www.motorolasolutions.com/doc
5.6 EU
Remote and Standalone Antenna Configurations
To comply with EU RF exposure requirements, antennas that are mounted externally at remote locations or
operating near users at stand-alone desktop of similar configurations must operate with a minimum separation
distance of 20 cm from all persons.
5.7 US and Canada
Co-located statement
To comply with FCC RF exposure compliance requirement, the antennas used for this transmitter must not be
co-located or operating in conjunction with any other transmitter/antenna except those already approved in this
filling.
Remote and Standalone Antenna Configurations
To comply with FCC RF exposure requirements, antennas that are mounted externally at remote locations or
operating near users at stand-alone desktop of similar configurations must operate with a minimum separation
distance of 20 cm from all persons.
Installation Guide
33
5.8 Power Supply
This device is powered from a 802.3af compliant power source which is UL approved and certified by the
appropriate agencies.
5.9 Radio Frequency Interference Requirements—FCC
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
•
•
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
Consult the dealer or an experienced radio/TV technician for help
Radio Transmitters (Part 15)
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Restricted Band 5.60 – 5.65 GHz
5.10 Radio Frequency Interference Requirements – Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
5.10.1 Radio Transmitters
For RLAN Devices:
The use of 5 GHz RLAN’s, for use in Canada, have the following restrictions:
• Restricted Band 5.60 – 5.65 GHz
L'utilisation de RLAN de 5 GHz, pour utilisation au Canada est soumise aux restrictions suivantes:
• Bande Restreinte de 5,60 à 5,65 GHz
This device complies with RSS 210 of Industry & Science Canada. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de
licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de
34
AP-6521E Access Point
brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible
de provoquer un fonctionnement indésirable
Label Marking: The Term "IC:" before the radio certification only signifies that Industry Canada technical
specifications were met.
5.11 CE Marking and European Economic Area (EEA)
The use of 2.4 GHz RLAN’s, for use through the EEA, have the following restrictions:
•
•
•
Maximum radiated transmit power of 100 mW EIRP in the frequency range 2.400 -2.4835 GHz.
France, outside usage is restricted to 2.4 – 2.454 GHz.
Italy requires a user license for outside usage.
5.12 Mexico
"La operación de este equipo está sujeta a lassiguientes dos condiciones: (1) es posible que este equipo o
dispositivo no cause interferencia perjudicialy (2) este equipo o dispositivo debe aceptar cualquierinterferencia,
incluyendo la que pueda causar suoperación no deseada."
5.13 Statement of Compliance
Motorola Solutions hereby, declares that this device is in compliance with the essential requirements and other
relevant provisions of Directive 1999/5/EC. A Declaration of Conformity may be obtained from
http://www.motorolasolutions.com/doc.
Installation Guide
35
5.14 Waste Electrical and Electronic Equipment (WEEE)
English: For EU Customers: All products at the end of their life must be returned to Motorola Solutions for
recycling. For information on how to return product, please go to:
http://www.motorolasolutions.com/recycling/weee.
Français: Clients de l'Union Européenne: Tous les produits en fin de cycle de vie doivent être retournés à
Motorola Solutions pour recyclage. Pour de plus amples informations sur le retour de produits, consultez :
http://www.motorolasolutions.com/recycling/weee.
Español: Para clientes en la Unión Europea: todos los productos deberán entregarse a Motorola Solutions al final
de su ciclo de vida para que sean reciclados. Si desea más información sobre cómo devolver un producto, visite:
http://www.motorolasolutions.com/recycling/weee.
Български: За клиенти от ЕС: След края на полезния им живот всички продукти трябва да се връщат на
Motorola Solutions за рециклиране. За информация относно връщането на продукти, моля отидете на
адрес: http://www.motorolasolutions.com/recycling/weee.
Deutsch: Für Kunden innerhalb der EU: Alle Produkte müssen am Ende ihrer Lebensdauer zum Recycling an
Motorola Solutions zurückgesandt werden. Informationen zur Rücksendung von Produkten finden Sie unter
http://www.motorolasolutions.com/recycling/weee.
Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del rispettivo ciclo di vita devono essere
restituiti a Motorola Solutions al fine di consentirne il riciclaggio. Per informazioni sulle modalità di restituzione,
visitare il seguente sito Web: http://www.motorolasolutions.com/recycling/weee.
Português: Para clientes da UE: todos os produtos no fim de vida devem ser devolvidos à Motorola Solutions
para reciclagem. Para obter informações sobre como devolver o produto, visite:
http://www.motorolasolutions.com/recycling/weee.
Nederlands: Voor klanten in de EU: alle producten dienen aan het einde van hun levensduur naar Motorola
Solutions te worden teruggezonden voor recycling. Raadpleeg http://www.motorolasolutions.com/recycling/weee
voor meer informatie over het terugzenden van producten.
Polski: Klienci z obszaru Unii Europejskiej: Produkty wycofane z eksploatacji nale¿y zwróciæ do firmy Motorola
Solutions w celu ich utylizacji. Informacje na temat zwrotu produktów znajduj¹ siê na stronie internetowej
http://www.motorolasolutions.com/recycling/weee.
Čeština: Pro zákazníky z EU: Všechny produkty je nutné po skonèení jejich životnosti vrátit spoleènosti Motorola
Solutions k recyklaci. Informace o zpùsobu vrácení produktu najdete na webové stránce:
http://www.motorolasolutions.com/recycling/weee.
Eesti: EL klientidele: kõik tooted tuleb nende eluea lõppedes tagastada taaskasutamise eesmärgil Motorola
Solutions'ile. Lisainformatsiooni saamiseks toote tagastamise kohta külastage palun aadressi:
http://www.motorolasolutions.com/recycling/weee.
Magyar: Az EU-ban vásárlóknak: Minden tönkrement terméket a Motorola Solutions vállalathoz kell eljuttatni
újrahasznosítás céljából. A termék visszajuttatásának módjával kapcsolatos tudnivalókért látogasson el a
http://www.motorolasolutions.com/recycling/weee weboldalra.
Svenska: För kunder inom EU: Alla produkter som uppnått sin livslängd måste returneras till Motorola Solutions
för återvinning. Information om hur du returnerar produkten finns på
http://www.motorolasolutions.com/recycling/weee.
Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet on palautettava kierrätettäväksi Motorola
Solutions-yhtiöön, kun tuotetta ei enää käytetä. Lisätietoja tuotteen palauttamisesta on osoitteessa
http://www.motorolasolutions.com/recycling/weee.
36
AP-6521E Access Point
Dansk: Til kunder i EU: Alle produkter skal returneres til Motorola Solutions til recirkulering, når de er udtjent. Læs
oplysningerne om returnering af produkter på: http://www.motorolasolutions.com/recycling/weee.
Ελληνικά: Για πελάτες στην Ε.Ε.: Όλα τα προϊόντα, στο τέλος της διάρκειας ζωής τους, πρέπει να επιστρέφονται
στην Motorola Solutions για ανακύκλωση. Για περισσότερες πληροφορίες σχετικά με την επιστροφή ενός
προϊόντος, επισκεφθείτε τη διεύθυνση http://www.motorolasolutions.com/recycling/weee στο ∆ιαδίκτυο.
Malti: Għal klijenti fl-UE: il-prodotti kollha li jkunu waslu fl-aħħar tal-ħajja ta' l-użu tagħhom, iridu jiġu rritornati
għand Motorola Solutions għar-riċiklaġġ. Għal aktar tagħrif dwar kif għandek tirritorna l-prodott, jekk jogħġbok żur:
http://www.motorolasolutions.com/recycling/weee.
Românesc: Pentru clienţii din UE: Toate produsele, la sfârşitul duratei lor de funcţionare, trebuie returnate la
Motorola Solutions pentru reciclare. Pentru informaţii despre returnarea produsului, accesaţi:
http://www.motorolasolutions.com/recycling/weee.
Slovenski: Za kupce v EU: vsi izdelki se morajo po poteku življenjske dobe vrniti podjetju Motorola Solutions za
reciklažo. Za informacije o vračilu izdelka obiščite: http://www.motorolasolutions.com/recycling/weee.
Slovenčina: Pre zákazníkov z krajín EU: Všetky výrobky musia byť po uplynutí doby ich životnosti vrátené
spoločnosti Motorola Solutions na recykláciu. Bližšie informácie o vrátení výrobkov nájdete na:
http://www.motorolasolutions.com/recycling/weee.
Lietuvių: ES vartotojams: visi gaminiai, pasibaigus jų eksploatacijos laikui, turi būti grąžinti utilizuoti į kompaniją
„Motorola Solutions“. Daugiau informacijos, kaip grąžinti gaminį, rasite:
http://www.motorolasolutions.com/recycling/weee.
Latviešu: ES klientiem: visi produkti pēc to kalpošanas mūža beigām ir jānogādā atpakaļ Motorola Solutions
otrreizējai pārstrādei. Lai iegūtu informāciju par produktu nogādāšanu Motorola, lūdzu, skatiet:
http://www.motorolasolutions.com/recycling/weee.
Türkçe: AB Müşterileri için: Kullanım süresi dolan tüm ürünler geri dönüştürme için Motorola Solutions'ya iade
edilmelidir. Ürünlerin nasıl iade edileceği hakkında bilgi için lütfen şu adresi ziyaret edin:
http://www.motorolasolutions.com/recycling/weee.
5.15 TURKISH WEEE Statement of Compliance
EEE Yönetmeliğine Uygundur
Installation Guide
37
5.16 Japan (VCCI) - Voluntary Control Council for Interference Class B ITE
この装置は、情報処理装置等電波障害自主規制協議会 (VCCI)の基準に基づくク
ラス B 情報技術装置です。この装置は、家庭環境で使用することを目的としています
が、この装置がラジオやテレビジョン受信機に近接して使用されると、受信障害を引
き起こすことがあります。取扱説明書に従って正しい取り扱いをして下さい。
This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information
Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may
cause radio interference. Install and use the equipment according to the instruction manual.
5.17 Korea Warning Statement for Class B ITE
기종별
B 급 기기
( 가정용 방송통신기기 )
사용자안내문
이 기기는 가정용 (B 급 ) 으로 전자파적합등록을
한 기기로서 주로 가정에서 사용하는 것을 목적
으로 하며 , 모든 지역에서 사용할 수 있습니다 .
Class B (Broadcasting
This device obtained EMC registration mainly for home use
Communication Device for Home (Class B) and may be used in all areas.
Use)
5.18 Other Countries
Australia
Use of 5 GHz RLAN’s in Australia is restricted in the following band 5.50 – 5.65 GHz.
Brazil
Regulatory declarations for AP-6521 - BRAZIL
Note: The certification mark applied to the AP-6521 is for Restrict Radiation Equipment. This equipment operates
on a secondary basis and does not have the right for protection against harmful interference from other users
including same equipment types. Also this equipment must not cause interference to systems operating on primary
basis.
For more information consult the website http://www.anatel.gov.br
Declarações Regulamentares para AP-6521 - Brasil
Nota: "A marca de certificação se aplica ao Transceptor, modelo AP-650. Este equipamento opera em caráter
secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo,
e não pode causar interferência a sistemas operando em caráter primário.”
Para maiores informações sobre ANATEL consulte o site: http://www.anatel.gov.br
38
AP-6521E Access Point
Chile
“Este equipo cumple con la Resolución No 403 de 2008, de la Subsecretaria de telecomunicaciones, relativa a
radiaciones electromagnéticas.”.
"This device complies with the Resolution Not 403 of 2008, of the Undersecretary of telecommunications, relating
to electromagnetic radiation.”
Mexico
Restrict Frequency Range to: 2.450 – 2.4835 GHz.
Taiwan
NOTICE!
According to: Administrative Regulations on Low Power Radio Waves Radiated Devices
Article 12
Without permission granted by the DGT, any company, enterprise, or user is not allowed to change frequency,
enhance transmitting power or alter original characteristic as well as performance to an approved low power
radio-frequency devices.
Article 14
The low power radio-frequency devices shall not influence aircraft security and interfere legal communications; If
found, the user shall cease operating immediately until no interference is achieved.
The said legal communications means radio communications is operated in compliance with the
Telecommunications Act.
The low power radio-frequency devices must be susceptible with the interference from legal communications or
ISM radio wave radiated devices. Wireless devices operate in the frequency band of 5.25-5.35 GHz, limited for
Indoor use only.
臺灣
低功率電波輻射性電機管理辦法
第十二條
經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者均不得擅自
變更頻率、加大功率或變更原設計之特性及功能。
第十四條
低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發現有干擾現象
時,應立即停用,並改善至無干擾時方得繼續使用。
前項合法通信,指依電信規定作業之無線電通信。
低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干
擾。
Installation Guide
39
Wireless devices operate in the frequency band of 5.25-5.35 GHZ, limited for Indoor use.
在 5.25-5.35 赫頻帶內操作之無線資訊傳輸設備,限於室內使用。
Korea
For radio equipment using 2400~2483.5MHz or 5725~5825MHz, the following expressions should be displayed:
1. “This radio equipment cannot provide a service relevant to human life safety, as it can be crossed” through the
user manual, etc.
당해 무선설비 는전파혼 신 가능성이 있으므로 인명안전과 관련된 서비스는 할 수 없습니다
2. “This radio equipment cannot provide a service relevant to human life safety, as it can be crossed” through the
user manual, etc.
당해 무선설비 는전파혼 신 가능성이 있으므로 인명안전과 관련된 서비스는 할 수 없습니다
40
6
AP-6521E Access Point
Motorola Solutions Support Center
If you have a problem with your equipment, contact support for your region.
Contact information is available at: https://portal.motorolasolutions.com/Support/US-EN
When contacting Motorola Solutions support, please provide the following information:
• Serial number of the unit
• Model number or product name
• Software type and version number
Motorola Solutions responds to calls by e-mail, telephone, or fax within the time limits set forth in support
agreements. If you purchased your product from a Motorola Solutions business partner, contact that business
partner for support.
Customer Support Web Sites
The Motorola Solutions Support Central Web site, located at
https://portal.motorolasolutions.com/Support/US-EN.
provides information and online assistance including developer tools, software downloads, product manuals and
online repair requests.
Manuals
https://portal.motorolasolutions.com/Support/US-EN/Wireless+Networks.
General Information
Obtain additional information by contacting Motorola Solutions at:
Telephone (North America): 1-800-722-6234
Telephone (International): +1-631-738-5200
Website: http://www.motorolasolutions.com
Installation Guide
41
42
AP-6521E Access Point
Installation Guide
43
Motorola Solutions, Inc.
1301 E. Algonquin Rd.
Schaumburg, IL 60196-1078, U.S.A.
http://www.motorolasolutions.com
MOTOROLA, MOTO, MOTOROLA SOLUTIONS and the Stylized M Logo are trademarks or registered trademarks of Motorola Trademark
Holdings, LLC and are used under license. All other trademarks are the property of their respective owners.
© 2014 Motorola Solutions, Inc. All Rights Reserved.
MN000034A01
Revision B May 2014