AAMP of America PXDP2 Owner`s manual

®
Add iPod Capability to
Your Factory Radio
Owner’s
Manual
PXDP
SoundByte
iSimple Solutions®,
A division of AAMP of America™
13160 56th Court Clearwater, Florida 33760
Ph. 866-788-4237
support@isimplesolutions.com
©2009 AAMP of Florida, Inc.
01-27-11
Table of Contents
Pages
CHAPTER 1-Getting Started
1.1 Introduction
1.2 Precautions
1.3 Configuration & Harnesses
1.4 Programming the PXDP
4
4
5
6
CHAPTER 2-General Installation
2.1 Installation Location
2.2 Pre-Installation Checklist
2.3 Wiring Connections
2.4 Installation at Changer Location
2.5 Installation at Radio
7
8
8
10
11
CHAPTER 3 -Operation
3.1 Operation
3.2 Troubleshooting
3.3 Warranty
3.4 Warning
3.5 FCC Statement
13
15
16
16
17
Dipswitch Settings & Harness Guide
18
PXDP Connections
Factory Radio
(not included)
Vehicle Specific Harness
( actual harness may vary)
PXDP Interface
iPod Input
Chapter 1- Getting Started
1.1 Introduction
Thank you for purchasing the PXDP iPod Interface, by
iSimple®. The PXDP is designed to provide endless hours
of listening pleasure through most vehicles’ factory radios.
To ensure that your iPod performs correctly in your car or
truck, we recommend that you read this entire manual before
attempting installation of the PXDP interface.
The PXDP interface will allow you to connect your iPod to
a factory radio that has the ability to control a CD changer.
The PXDP is designed to be used with most iPod Models
featuring the 30 pin docking port.
1.2 Precautions (Important, Please Read)
UPDATING iPod FIRMWARE
For proper operation of the PXDP, your iPod must be
updated with the most recent version of Firmware from
Apple. This is done on your computer. To Update the
software on the iPod go to http://www.apple.com/ipod/
download/. Follow the directions on the website to complete
the download. There is no charge for this update.
PREVENTING DAMAGE TO YOUR VEHICLE OR iPod.
The manufacturer recommends unplugging the iPod when
not in use.To eliminate the risk of an electrical short, we
recommend disconnecting the car battery in most vehicles,
prior to installation except in the following situations:
• Vehicles equipped with on-board navigation should not
have the car’s battery disconnected. Doing so may cause
loss of memory settings. These settings would then have
to be reprogrammed by an authorized car dealer for a fee
to be paid by the vehicle’s owner. For these vehicles, we
recommend extreme caution when handling exposed 12V
power or ground wires/connectors.
4
•Vehicles that incorporate a security-code protecting the
radio. If the car’s battery or the radio’s power plugs are
disconnected, the radio will not operate without re-entering
the security-code. If you have access to the security-code,
feel comfortable disconnecting the battery and the radio’s
power connectors. Otherwise, do not disconnect the battery
and exercise extreme caution while handling exposed 12V
power or ground wires/connectors.
PROPER MOUNTING LOCATION
Securely install the interface in a location free from; heat,
humidity, moving parts or direct sunlight. Beware of hotair flow from your vehicle’s climate control system. We
recommend securing the interface to a suitable location, free
of sharp metal edges, using; double sided tape, Velcro or
wire ties.
PXDP Interface
Docking Cable
Vehicle Specific Harness
1.3 Configuration and Harness Selection
This section will instruct you on how to properly identify and/
or confirm the proper interface dip-switch configuration and
vehicle specific harness selection.
Use the guide located in the back of this manual on page 18
to locate your vehicle, inform you of the proper dip-switch
configuration for the interface, and the vehicle specific
harness that you will need for your particular vehicle.
Depending on the type of PXDP kit you purchased, it might
include a bundle of different vehicle harnesses or none at all.
If the kit contains many harnesses, only one will be needed
for your specific vehicle. If the kit came without any vehicle
harness, your authorized iSimple® dealer will have the
harness for you to purchase separately.
5
As you consult the application guide, please take a moment
to review our IMPORTANT COMPATIBILITY NOTES listed
with each of the vehicle manfactuers. These notes will
inform you of any issues or circumstances that can affect the
compatibility of our product with your factory audio system
and accessories. Some situations result in the loss of use
of some factory audio players. Please read and understand
these notes before proceeding with the installation.
1.6 Programming the PXDP
Now that you have identified the correct harness and dipswitch configuration using the application guide, it is now
time to program the interface. To program the interface, set
the dip-switches located on the side of the interface (see
Fig.1 below) to the congfiguration listed for your vehicle in
the application guide. Switches are in their default setting of
“off” in the up position and are turned “on” when switched
down. This programs the PXDP to work with the vehicle
in which it will be installed. The dip-switches MUST be set
before the interface is plugged into the vehicle. Otherwise
the PXDP will not work correctly.
Fig.1 Side view of Interface with dip switches
1 2
DIP
3
4
5
6
7 8
ON
Please Refer to Page 18 for Configuration Settings
PLEASE NOTE: If after installation you experience low
volume from the interface, Dipswitch 6 can be turned on
for a 6Db gain.
6
Chapter 2- General Installation
2.1 Installation Location
Most installations will require you to remove the factory
radio in order to plug in the vehicle specific harness. Some
vehicles may require you to connect the interface to a factory
pre-run CD changer cable. The location of these CD changer
cables will vary by vehicle. Some common locations of these
cables are in the trunk, behind the glove box, and in or under
a center console. ( see Fig.2 below)
Common Connection Locations
iPod
PXDP
interface
M EN U
iPod Docking Cable
(Sold Separately)
Refer to Application Guide
correct harness
V OL
DS P
TUN E
PWR
SEEK
S CA N
1
B AN D
DI S C
TA P E
2
3
IN F O
SEEK
TYP E
TR AF
4
AUTO
V OI
R DS
AUTO
EQ
5
6
Fig. 2
7
2.2 Pre-Installation Checklist
At this time and before beginning the installation
please ensure that:
• You have read and understand the precautions
outlined in section 1.2
• Your iPod’s Firmware is up to date. (section
1.2)
• You have your radio’s security code.(when
applicable, see section 1.2)
• The dip-switches on the interface have been
set with the proper configuration. (see section
1.3)
• You have in your possession the correct
harness for your vehicle. (see sec. 1.3)
• You have determined your installation location.
(see section 2.1)
If any of these steps has not been taken,
STOP. Only when ALL of these steps have been
taken should you proceed with the rest of the
installation.
2.3 Wiring Connections
Some vehicle specific harnesses require wiring connections
that involve splicing of wires. If you are not confident in
making these connections to your radio’s wiring harness, we
recommend you seek professional installation. You can visit
www.isimplesolutions.com and click on the dealer link at the
top of the page to find an authorized professional installer.
Make these connections only after verifying the proper circuit
on your radio harness with a voltmeter. With the key OFF
and the negative test lead of the voltmeter firmly touching a
bare metal chassis part of your car, begin probing the wires
in the main radio harness with the positive test lead. The
constant 12V+ circuit should read a continuous 12 volts or
higher.
8
Once you’ve identified the constant 12V+ circuit, strip
back about 1/8” of the insulation. Now take the positive
test lead and insert it into the wire stranding so that you
can now probe for a suitable ground location in the dash
cavity using the negative test lead. Bare chassis metal is
the recommended ground spot. The voltmeter will read a
constant 12 volts or higher when you have found a good
ground point. Attach the BLACK ground wire to this spot
with either an existing bolt or screw or use a metal piercing
screw. You also have the option of splicing into the ground
wire in the main radio harness. Probe the remaining wires
with the negative test lead until you again find a circuit that
reads a constant 12 volts on the voltmeter. When you’ve
found a circuit that reads constant 12 volts, turn the dash
light dimmer control to make sure you have not probed the
illumination dimmer circuit. If the circuit continues to read
a constant 12 volts or higher regardless of the dimmer
position, you have found the ground wire. If not, continue
testing until you do. Some vehicles do not have a ground
wire in their main radio harness and instead ground through
their mounting brackets to the dash. In these cases, you
will have to ground the black wire to the bare metal chassis
inside the dash . Once the ground wire is connected, please
finish your wiring connections by splicing in the external
YELLOW wire from the vehicle specific harness.
Vehicle Specific Harnesses that require wiring
connections:
PXHFD1 – connect the Yellow wire to constant 12V+ &
connect the Black wire to ground.
PXHFD2 – connect the Yellow wire to constant 12V+ &
connect the Black wire to ground.
PXHFD3 – connect the Yellow wire to constant 12V+ &
connect the Black wire to ground.
PXHGM3 – connect the Yellow wire to constant 12V+ &
connect the Black wire to ground.
PXHVW2 – connect both the Black and Black/White wires to
ground.
9
2.4 Installation at the CD Changer Location
In this section you will learn how to install the PXDP in the
factory CD changer location. If your vehicle is equipped with
a factory CD changer you will need to disconnect it from
the factory pre-run harness in order to connect the PXDP
interface. If your vehicle is not equipped with a factory CD
changer, you will need to locate the factory pre-run harness.
This may involve the removal of the; center console, glove
box, or carpeted side panels in the trunk. Please consult
your vehicle’s dealership or a local car audio professional
for instruction or assistance with locating the factory CD
changer connection if necessary.
1. Connect your vehicle specific Harness to the factory prerun CD changer harness in the vehicle.
2. Make any necessary wiring connections on your vehicle
specific harness. Please see section 2.3 for details on
making these wiring connections.
3. Now that the interface is connected to the radio, you
will need to test the operation of the interface before
permanently running the black iPod docking cable or reassembling the dash.
First, connect the black iPod cable to the iPod. The iPod
should indicate that it is being charged. Turn on the factory
radio and press the button that would activate the factory CD
changer to select the iPod. It may take up to three minutes
for the interface to initialize to the radio (this only happens
the very first time you select the iPod). Once the iPod has
been selected, press Play on the iPod. You should be able
to hear the music on your iPod through your factory radio.
Now press the “Next Track” button on the radio. The iPod
should change to the next song on the iPod. By pressing
the “Previous Track” button on the radio the iPod should
change to the previous song. With the operation of the
interface confirmed, you may continue with the installation.
If you experience difficulties in operation, please see our
troubleshooting chart in section 3.2.
10
4. Decide on a convenient location to mount your iPod.
5. Run the docking cable from the interface to the desired
mounting location. Use caution to not cut, pinch, or crimp
the cable during this step. Avoid moving parts, vehicle wiring
harnesses and areas of excessive heat when routing the
cable.
6. Secure the interface in the vehicle using; double sided
tape, Velcro or wire ties. Make sure to check for proper
clearance and avoid moving parts. Take into account the size
of the interface and the wire harness and do not force the
interface and harness into a space that is too tight, damage
to the harness may result.
7. Now that the interface is secured and the docking cable
has been run, you are ready to enjoy your iPod in your
vehicle!
2.5 Installation at the Radio
In this section you will learn how to install the PXDP behind
the radio. If your vehicle is equipped with a factory CD
changer or other external audio source, you will need to
disconnect it from the back of the radio in order to connect
the PXDP interface.
1. Carefully remove the radio from the vehicle. If your radio
uses a Security Code, make sure that you have the code
before unplugging the radio. Some vehicles require the use
of special tools to remove the radio. Please consult your
vehicle’s dealership or a local car audio professional for
instruction or assistance with radio removal if necessary.
2. Make any necessary wiring connections on your vehicle
specific harness. Please see section 2.3 for details on
making these wiring connections.
3. Connect the Vehicle Specific Harness to the CD changer
port on the back of the radio. Be sure to make a firm
connection but do not force it. If there is difficulty making the
connection, please consult the application guide to confirm
your vehicle specific harness selection.
11
4. Now that the interface is connected to the radio, you
will need to test the operation of the interface before
permanently running the black iPod docking cable or reassembling the dash.
First, connect the black iPod cable to the iPod. The iPod
should indicate that it is being charged. Turn on the factory
radio and press the button that would activate the factory CD
changer to select the iPod. It may take up to three minutes
for the interface to initialize to the radio (this only happens
the very first time you select the iPod). Once the iPod has
been selected, press Play on the iPod. You should be able
to hear the music on your iPod through your factory radio.
Now press the “Next Track” button on the radio. The iPod
should change to the next song on the iPod. By pressing
the “Previous Track” button on the radio the iPod should
change to the previous song. With the operation of the
interface confirmed, you may continue with the installation.
If you experience difficulties in operation, please see our
troubleshooting chart in section 3.2.
5. Decide on a convenient location to mount your iPod.
6. Run the docking cable from the interface to the desired
mounting location. Use caution to not cut, pinch, or crimp
the cable during this step. Avoid moving parts, vehicle wiring
harnesses and areas of excessive heat when routing the
cable.
7. Secure the interface in the dash cavity behind the radio
using; double sided tape, Velcro or wire ties. Make sure to
check for proper clearance and avoid moving parts. Take into
account the size of the interface and the wire harness and
do not force the interface and harness into a space that is
too tight, damage to the harness may result.
8. Now that the interface is secured and the docking cable
has been run, you may reinstall the radio and replace any
panels that may have been removed to access the radio.
You are ready to enjoy your iPod in your vehicle!
12
Chapter 3- Operation
3.1 Operation
SELECTING THE IPOD
To select the iPod from the radio, press the button that would
normally activate the factory CD changer. This button varies
by vehicle manufacturers. In some applications the PXDP is
accessed like an XM reciever, In these cases you will press
the appropriate activation button. Some radio models require
pressing the “Seek >” button once, after pressing the CD
button. Yet, it may also be necessary to press Play on the
iPod itself to begin playback. In some cases, if it is the first
time selecting the iPod from the radio it may take up to three
minutes for the PXDP to initialize.
CONTROLLING THE IPOD FROM THE RADIO
With the PXDP interface, the radio will control the iPod as
if it were a factory CD changer. Therefore, operation will be
done by using the same buttons you would use to control
a factory CD changer. For more details on your particular
radio, consult your vehicle’s owner’s manual.
The PXDP interface allows you to skip songs forward and
backwards and also to fast forward and rewind through a
particular song. In general, most radios will utilize “seek” or
“track” buttons to control these functions.
CONTROLLING THE IPOD FROM THE IPOD
The PXDP interface allows you to keep full control of the
iPod from the click wheel. You can browse files and change
playlist on the iPod. You can also skip songs forward and
backwards from the iPod. The PXDP interface does not
disable any functionality of the iPod!
13
RADIO DISPLAY DURING IPOD OPERTION
Some factory radio’s may show DISC and TRACK numbers
on the display of the radio. The PXDP interface does not
send any information from the iPod to the radio. This means
that the DISC and TRACK numbers shown on the display
will not and can not reflect the song number on the iPod
due to the complex nature of the music library. Some factory
radio’s may flash zero’s on the display of the radio, or toggle
back and forth between 1:00 and 2:00. All these are normal
behaviors and do not represent a malfunction.
CONTROLING THE IPOD FROM THE STEERING WHEEL
CONTROLS
If your vehicle’s steering wheel controls have the ability to
select track and control the forward and rewind functions of
your factory CD changer, then they will also control these
same functions on the iPod.
14
3.2 Troubleshooting
Symptom
Cause
Remedy
No Power
Blown fuse in vehicle fuse
block.
Replace fuse with same
amp rating. If the fuse
blows again, call tech
support.
No Power
Bad connection.
Check cable and wiring
connection.
Alternator noise is heard
(Changes with Engine RPM)
Improper wiring creates a
ground loop.
Install a Ground loop isolator or seek professional
service from a local car
audio shop.
You can hear music from
the iPod but you cant control it from the radio.
The Firmware on the iPod
may not be updated.
Update the Firmware on
the iPod. See section 1.2
of this manual.
Radio is not recognizing
PXDP interface
Bad cables or cables are
not connected properly
between converter box and
car radio.
Check connection and
interface.
ration for your car. (See
section 1.3).
Radio is not recognizing
PXDP interface
Yellow and black wires are
not connected to Constant
12V+ and Ground. (When
applicable).
Please read wiring instructions in chapter 2 of this
manual and see if your car
requires to connect the
yellow and black cable to
power and ground.
iPod Audio is Low or
Distorted
PXDP interface is connected with an external CD
changer or other external
factory audio source.
Disconnect the factory
external audio source.
iPod is not charging
Yellow and black wires are
not connected to Constant
12V+ and Ground. (When
applicable).
Please read your vehicles
section in this manual and
see if your car requires to
connect the yellow and
black cable to power and
ground.
Radio is not recognizing
PXDP interface
-
15
3.3 Warranty
One Year Limited Warranty
The quality controls used in the manufacture of this product
This warranty covers any supplied or manufactured parts
of this product that, upon inspection by iSimple authorized
personnel, is found to have failed in normal use due to
defects in material or workmanship. This warranty does not
apply to installation expenses.
Attempting to service or modify this unit, operating this unit
under conditions other than the recommended voltage will
render this WARRANTY VOID.
Unless otherwise prescribed by law, iSimple shall not be
liable for any personal injury, property damage and or any
incidental or consequential damages of any kind (including
water damage) resulting from malfunctions, defects, misuse,
improper installation or alteration of this product.
All parts of this iSimple product are guaranteed for a period
of 1 year as follows:
Within the first 12 months from date of purchase, subject
to the conditions above, iSimple will repair or replace the
product at their discretion, if it is defective in material or
workmanship providing it is returned to an Authorized
iSimple’s Dealer, with PROOF OF PURCHASE from an
authorized iSimple dealer.
3.4 Warning
This equipment may be reset by unintentional electrostatic
discharge during operation. Exposure to direct sunlight or
extreme heat may cause damage or malfunction.
16
3.5 FCC Class B Radio Frequency Interference
Statement
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part
15 of FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more
of the following measures:
1. Reorientate or relocate the receiving antenna.
2. Increase the separation between the equipment and
receiver.
3. Connect the equipment into an outlet on a circuit different
from that of which the receiver is connected.
4. Consult the dealer or an experienced radio / television
technical for help
Notice : The changes or modifications not expressly
approved by the party responsible for compliance
could void the user authority to operate the equipment.
17
18
Dipswitch Settings & Harness Applications
Make
Acura
Model
CL
CL
Integra
Integra
Legend
RL
RL
RSX
TL
TL
Vigor
All Models
MDX
SLX
NSX
Year
1998-2000
1996-1997
1998-2001
1992-1997
1992-1995
1998-2002
1996-1997
2002
1999-2002
1996-1997
1992-1994
2003-2007
All Years
All Years
All Years
Part #
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
Not Compatible
Not Compatible
Not Compatible
Not Compatible
Harness
PXHHD1
PXHCH2
PXHHD1
PXHCH2
PXHCH2
PXHHD1
PXHCH2
PXHHD1
PXHHD1
PXHCH2
PXHCH2
Dip Switch Settings**
1,4,8 ON
1,4,8 ON
1,4,8 ON
1,4,8 ON
1,4,8 ON
1,4,8 ON
1,4,8 ON
1,4,8 ON
1,4,8 ON
1,4,8 ON
1,4,8 ON
Vehicle Specific Notes
IMPORTANT ACURA APPLICATION INFORMATION
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function. Not compatible with factory radios that have an in
dash 6 disk cd changer. Not compatible with navigation radios.
Make
Audi
Model
All Models (Except Below)
All Models (Except Below)
Year
1998-2004
1998-2004
Part #
PXDP
PXDP
Harness
Dip Switch Settings*
PXHAD1
1,8 ON
PXHAD2 + PXHVW2*
1,8 ON
IMPORTANT AUDI APPLICATION INFORMATION
Vehicle Specific Notes
Connect at pre-wired 13-pin cable in the left rear trunk.
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function. Vehicles with Symphony sound systems must use
special adapter harness PXHAD2 as well as PXHVW2 and connect at radio.
Make
BMW
Model
3 Series
5 Series
7 Series
Mini
X5
Z3/Z5
Z4
Year
1996-2005
1996-2005
1999-2001
2001-2006
1999-2005
1998-2003
2003-2005
Part #
ISBM72
ISBM72
ISBM72
ISBM72
ISBM72
ISBM72
ISBM72
Harness
Dip Switch Settings*
Included
3,4,8, ON
Included
3,4,8, ON
Included
3,4,8, ON
Included
3,4,8, ON
Included
3,4,8, ON
Included
3,4,8, ON
Included
3,4,8, ON
IMPORTANT BMW APPLICATION INFORMATION
ISBM71: Not Compatible with Factory Head Units with DSP. "DSP" will be indicated on a radio button. Not compatible with vehicles equipped with iDrive.
*Dip Switch Settings: Please See Product Instructions for Dip Switch Configuration Settings
Vehicle Specific Notes
Not Compatible with DSP radios, Trunk Mounting Location
Not Compatible with DSP radios, Trunk Mounting Location
Not Compatible with DSP radios, Trunk Mounting Location
Not Compatible with DSP radios, Trunk Mounting Location
Not Compatible with DSP radios, Trunk Mounting Location
Not Compatible with DSP radios, Trunk Mounting Location
Not Compatible with DSP radios, Trunk Mounting Location
Make
Buick
Model
Century
Le Sabre
Park Ave
Rainier
Regal
Rendezvous
Riviera
Roadmaster
Allure
LaCrosse
Year
1997-2003
1999-2002
1995-2005
2005
1995-2003
2003-2005
1996-1999
1995-1996
2005
2005
Part #
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
Not Compatible
Not Compatible
Harness
PXHGM1 & GMH32T
PXHGM3
PXHGM1 & GMH32T
PXHGM3
PXHGM1 & GMH32T
PXHGM3
PXHGM1 & GMH32T
PXHGM1 & GMH32T
Dip Switch Settings*
3,8 ON
1,3,8 ON
3,8 ON
1,3,8 ON
3,8 ON
1,3,8 ON
3,8 ON
3,8 ON
Vehicle Specific Notes
Must use GMH32T "T"-harness then plug *PXHGM1 behind radio.
Must use GMH32T "T"-harness then plug *PXHGM1 behind radio.
Must use GMH32T "T"-harness then plug *PXHGM1 behind radio.
Must use GMH32T "T"-harness then plug *PXHGM1 behind radio.
Must use GMH32T "T"-harness then plug *PXHGM1 behind radio.
IMPORTANT BUICK APPLICATION INFORMATION
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function. GM vehicles 1998 – 2004 not equipped with a factory
slave may not be able to support an external device. Therefore the PXDP may not be compatible. If you are an experienced installer, you can retain XM. Please follow this link to the Tech Brief to retain XM:
http://peripheralelectronics.com/web/tech_dept.asp. 1995-1999 Radios with built in CD player (Except Corvette) are NOT compatible because they do not have CD changer control functions.
Make
Cadillac
Model
Catera
Deville
El Dorado
Escalade
Escalade
Seville
Year
2001
1995-2003
1995-2002
1999-2002
2003-2006
1995-2005
Part #
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
Harness
Dip Switch Settings*
PXHGM2
3,8 ON
PXHGM2
3,8 ON or 1,3,8 ON
PXHGM2
3,8 ON
PXHGM1
3,8 ON
PXHGM3
1,3,8 ON or 2,3,8 ON
PXHGM2
3,8 ON
IMPORTANT CADILLAC APPLICATION INFORMATION
Vehicle Specific Notes
Behind radio or Trunk Mounting Location
Behind radio or Trunk Mounting Location
Trunk Mounting Location
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function. GM vehicles 1998 – 2004 not equipped with a factory
slave may not be able to support an external device. Therefore the PXDP may not be compatible. If you are an experienced installer, you can retain XM. Please follow this link to the Tech Brief to retain XM:
http://peripheralelectronics.com/web/tech_dept.asp. 1995-1999 Radios with built in CD player (Except Corvette) are NOT compatible because they do not have CD changer control functions.
Make
Chevrolet
19
Model
Astro Van
Avalanche
Avalanche
Blazer
Camaro
Cavalier
Cavalier
Colorado
Corvette
Corvette
Impala
Impala
Lumina
Malibu
Monte Carlo
Year
1996-2005
2002
2003-2006
1998-2002
1997-2002
1996-1999
2003-2005
2005
1997-2004
1997-2004
1995-1999
2000-2005
1996-1999
1997-2000
1995-1999
Part #
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
Harness
PXHGM1
PXHGM1
PXHGM3
PXHGM1
PXHGM1
PXHGM1
PXHGM3
PXHGM3
PXHGM2
PXHGM4
PXHGM1
PXHGM3
PXHGM1
PXHGM1
PXHGM1
Dip Switch Settings*
3,8 ON
3,8 ON
1,3,8 ON
3,8 ON
3,8 ON
3,8 ON
1,3,8 ON or 2,3,8 ON
1,3,8 ON
3,8 ON
3,8 ON
3,8 ON
1,3,8 ON
3,8 ON
3,8 ON
3,8 ON
Vehicle Specific Notes
Trunk Mounting Location
As a substitute, Can also use PXHGM1 and GMH20T Harnesses
20
Make
Chevrolet
Model
Monte Carlo
Silverado
Silverado
Suburban
Suburban
Tahoe
Tahoe
Trailblazer
Venture
Venture
Year
2000-2005
1996-2002
2003-2006
1995-2002
2003-2006
1995-2002
2003-2006
2002-2007
1997-1999
2004-2005
Part #
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
Harness
Dip Switch Settings*
PXHGM3
3,8 ON
PXHGM1
3,8 ON
PXHGM3
1,3,8 ON
PXHGM1
3,8 ON
PXHGM3
1,3,8 ON
PXHGM1
3,8 ON
PXHGM3
1,3,8 ON
PXHGM3
1,3,8 ON or 2,3,8 ON
PXHGM1
3,8 ON
PXHGM3
1,3,8 ON or 2,3,8 ON
IMPORTANT CHEVROLET APPLICATION INFORMATION
Vehicle Specific Notes
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function. GM vehicles 1998 – 2004 not equipped with a factory
slave may not be able to support an external device. Therefore the PXDP may not be compatible. If you are an experienced installer, you can retain XM. Please follow this link to the Tech Brief to retain XM:
http://peripheralelectronics.com/web/tech_dept.asp. 1995-1999 Radios with built in CD player (Except Corvette) are NOT compatible because they do not have CD changer control functions.
Make
Chrysler
Model
All Models
All Models
All Models
Pacifica
Sebring
Year
2002-2005
1999--2001
1995-1999*
2006
2006
Part #
PXDP
PXDP
PXDP
PXDP
PXDP
Harness
Dip Switch Settings*
Vehicle Specific Notes
PXHCH3
4,8 ON
Must be non-CANBUS, if radio is an REF,REC,RAQ, RAK series, vehicles are not compatible
PXHCH2
4,8 ON
*1999 Radios with rounded corners use PXHCH2
PXHCH1
1,4,8 ON
*1999 Radios with square corners use PXHCH1
PXHCH3
4,8 ON
PXHCH3
4,8 ON
IMPORTANT CHRYSLER APPLICATION INFORMATION
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function. To determine if your 2002-2005 vehicle is compatible,
factory radio must have "Disk ^" on preset 1. Vehicle must be non-CANBUS, if radio is an REF,REC,RAQ, RAK series, vehicles are not compatible. The series is indicated on the front of the radio. 1999 Chrysler vehicles have one of two different style radios.
These two radios use different harnesses. The shape of the radio face will determine which harness you will use. If your radio face is SQUARE, you will use the harness part# PXHCH1. If your radio face is OVAL (rounded corners), you will use the harness
part# PXHCH2.
Make
Dodge
Model
All Models
All Models
All Models
Year
2002-2005
1999*-2001
1995-1999*
Part #
PXDP
PXDP
PXDP
Harness
Dip Switch Settings*
Vehicle Specific Notes
Must be non-CANBUS, if radio is an REF,REC,RAQ, RAK series, vehicles are not compatible
PXHCH3
4,8 ON
PXHCH2
4,8 ON
*1999 Radios with rounded corners use PXHCH2
PXHCH1
1,4,8 ON
*1999 Radios with square corners use PXHCH1
IMPORTANT DODGE APPLICATION INFORMATION
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function. To determine if your 2002-2005 vehicle is compatible,
factory radio must have "Disk ^" on preset 1. Vehicle must be non-CANBUS, if radio is an REF,REC,RAQ, RAK series, vehicles are not compatible. The series is indicated on the front of the radio. 1999 Chrysler vehicles have one of two different style radios.
These two radios use different harnesses. The shape of the radio face will determine which harness you will use. If your radio face is SQUARE, you will use the harness part# PXHCH1. If your radio face is OVAL (rounded corners), you will use the harness
part# PXHCH2.
Make
Eagle
Model
All Models
Year
1995-1998
Part #
PXDP
Harness
Dip Switch Settings*
PXHCH1
1,4,8 ON
IMPORTANT EAGLE APPLICATION INFORMATION
Vehicle Specific Notes
All models must have “Disc ^ ” printed on Preset Button # 1.
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function. If your vehicle is equipped with a factory CD changer,
you must disconnect it in order to be able to install the interface. You will lose the use of the factory CD changer to gain use of your iPod.
Make
Ford
Model
Crown Victoria
Crown Victoria
Crown Victoria
Escape
Econoline
Econoline
Escort
Excursion
Expedition
Expedition
Explorer
Explorer
Explorer
Freestar
F-series Pick Up
F-series Pick Up
Focus
Mustang
Ranger
Ranger
Sport Trac
Taurus
Thunderbird
Windstar
Year
1998-2003
1995-1997
1995-1997
2001-2004
1998-2004
1997
1997-2004
2000-2004
1999-2002
1997-1998
1998-2004
1995-1997
1995-1997
2004
1998-2003
1995-1997
2000-2003
2001-2003
1998-2004
1995-1997
2000-2004
1996-2005
2000-2004
1999-2004
Part #
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
Harness
Dip Switch Settings*
PXHFD3
2,8 ON
PXHFD2
2,8 ON
PXHFD1
2,8 ON
PXHFD3
2,8 ON
PXHFD3
2,8 ON
PXHFD2
2,8 ON
PXHFD2
2,8 ON
PXHFD3
2,8 ON
PXHFD3
2,8 ON
PXHFD2
2,8 ON
PXHFD3
2,8 ON
PXHFD2
2,8 ON
PXHFD1
2,8 ON
PXHFD3
2,8 ON
PXHFD3
2,8 ON
PXHFD2
2,8 ON
PXHFD4
2,8 ON
PXHFD3
2,8 ON
PXHFD3
2,8 ON
PXHFD2
2,8 ON
PXHFD3
2,8 ON
PXHFD1
2,8 ON
PXHFD3
2,8 ON
PXHFD3
2,8 ON
IMPORTANT FORD APPLICATION INFORMATION
Vehicle Specific Notes
*If equipped with JBL, use PXHFD1 at Rear Control Unit in trunk
*If equipped with JBL, use PXHFD1 at Rear Control Unit in trunk
Not compatible with factory installed Blaupunkt radio
Trunk Mounting Location
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function. Not compatible with factory radios with built-in 6-disc
CD changers. Compatible with factory navigation radios.
Make
GMC
Model
Canyon
Envoy
Envoy
Denali
Denali
Jimmy
Sonoma
Safari
Savana
Sierra
Sierra
Suburban
Suburban
Yukon/XL
Yukon/XL
Year
2004-2006
1999-2001
2002-2007
1995-2002
2003-2006
1998-2002
1998-2002
1996-2005
1999-2000
1995-2002
2003-2006
1995-2002
2003-2006
1995-2002
2003-2006
Part #
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
Harness
Dip Switch Settings*
Vehicle Specific Notes
PXHGM3
1,3,8 ON or 2,3,8 ON
PXHGMTCD harness is required to retain factory CD Changer (if equipped)
PXHGM1
3,8 ON
PXHGM3
1,3,8 ON or 2,3,8 ON
PXHGM1
3,8 ON
PXHGM3
1,3,8 ON
PXHGM1
3,8 ON
PXHGM1
3,8 ON
PXHGM1
3,8 ON
PXHGM1
3,8 ON
PXHGM1
3,8 ON
PXHGM3
1,3,8 ON
PXHGM1
3,8 ON
PXHGM3
1,3,8 ON
PXHGM1
3,8 ON
PXHGM3
1,3,8 ON
IMPORTANT GMC APPLICATION INFORMATION
21
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function. GM vehicles 1998 – 2004 not equipped with a factory
slave may not be able to support an external device. Therefore the PXDP may not be compatible. If you are an experienced installer, you can retain XM. Please follow this link to the Tech Brief to retain XM:
http://peripheralelectronics.com/web/tech_dept.asp. 1995-1999 Radios with built in CD player (Except Corvette) are NOT compatible because they do not have CD changer control functions.
22
Make
Honda
Model
Accord
Accord
Civic
Civic
CRV
CRV
Del Sol
Element
Insight
Odyssey
Odyssey
Passport
Prelude
Prelude
S2000
All Models
Accord
Pilot
Ridgeline
S2000
Year
1998-2002
1992-1997
1998-2004
1992-1997
1998-2004
1997
1993-1997
2002
2001-2004
1995-1997
1998-2004
1998-2002
1998-2001
1992-1997
2000-2003
2005-2007
2003-2004
All Years
All Years
2004
Part #
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
Not Compatible
Not Compatible
Not Compatible
Not Compatible
Not Compatible
Harness
PXHHD1
PXHCH2
PXHHD1
PXHCH2
PXHHD1
PXHCH2
PXHCH2
PXHHD1
PXHHD1
PXHCH2
PXHHD1
PXHHD1
PXHHD1
PXHCH2
PXHHD1
Dip Switch Settings*
1,4,8 ON
1,4,8 ON
1,4,8 ON
1,4,8 ON
1,4,8 ON
1,4,8 ON
1,4,8 ON
1,4,8 ON
1,4,8 ON
1,4,8 ON
1,4,8 ON
1,2,4,8 ON
1,4,8 ON
1,4,8 ON
1,4,8 ON
Vehicle Specific Notes
IMPORTANT HONDA APPLICATION INFORMATION
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function. Not compatible with factory radios that have an in
dash 6 disk cd changer. Not compatible with navigation radios.
Make
Hummer
Model
H2
H3
Year
2003-2006
2005
Part #
PXDP
PXDP
Harness
Dip Switch Settings*
PXHGM3
1,3,8 ON or 2,3,8 ON
PXHGM3
1,3,8 ON or 2,3,8 ON
IMPORTANT HUMMER APPLICATION INFORMATION
Vehicle Specific Notes
*2003-2005 Must disable factory XM Tuner if equipped
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function.
Make
Isuzu
Model
Amigo
Rodeo
Trooper
Year
1998-2002
1998-2002
1998-2002
Part #
PXDP
PXDP
PXDP
Harness
Dip Switch Settings*
PXHTY3
1,2,4,8 ON
PXHTY3
1,2,4,8 ON
PXHTY3
1,2,4,8 ON
IMPORTANT ISUZU APPLICATION INFORMATION
Vehicle Specific Notes
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function.
Make
Jaguar
Model
S-Type
Year
2000-2002
Part #
PXDP
Harness
Dip Switch Settings*
PXHFD4
2,8 ON
IMPORTANT JAGUAR APPLICATION INFORMATION
Vehicle Specific Notes
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function.
Make
Jeep
Model
All Models
All Models
All Models
Year
2002-2005
1999*-2001
1995-1999*
Part #
PXDP
PXDP
PXDP
Harness
Dip Switch Settings*
Vehicle Specific Notes
Must be non-CANBUS, if radio is an REF,REC,RAQ, RAK series, vehicles are not compatible
PXHCH3
4,8 ON
PXHCH2
4,8 ON
*1999 Radios with rounded corners use PXHCH2
PXHCH1
1,4,8 ON
*1999 Radios with square corners use PXHCH1
IMPORTANT JEEP APPLICATION INFORMATION
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function. To determine if your 2002-2005 vehicle is compatible,
factory radio must have "Disk ^" on preset 1. Vehicle must be non-CANBUS, if radio is an REF,REC,RAQ, RAK series, vehicles are not compatible. The series is indicated on the front of the radio. 1999 Chrysler vehicles have one of two different style radios.
These two radios use different harnesses. The shape of the radio face will determine which harness you will use. If your radio face is SQUARE, you will use the harness part# PXHCH1. If your radio face is OVAL (rounded corners), you will use the harness
part# PXHCH2.
Make
Lincoln
Model
Aviator
Continental
Continental
Continental*
LS
Mark VIII
Navigator
Navigator
Town Car
Town Car
Town Car*
Year
2002-2003
1998-2004
1995-1997
1995-1997
2000-2003
1995-1998
1999-2003
1997-1998
1998-2003
1995-1997
1995-1997
Part #
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
Harness
Dip Switch Settings*
PXHFD3
2,8 ON
PXHFD3
2,8 ON
PXHFD2
2,8 ON
PXHFD1
2,8 ON
PXHFD3
2,8 ON
PXHFD2
2,8 ON
PXHFD3
2,8 ON
PXHFD2
2,8 ON
PXHFD3
2,8 ON
PXHFD2
2,8 ON
PXHFD1
2,8 ON
IMPORTANT LINCOLN APPLICATION INFORMATION
Vehicle Specific Notes
*If equipped with JBL, use PXHFD1 at Rear Control Unit in trunk
*If equipped with JBL, use PXHFD1 at Rear Control Unit in trunk
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function. Not compatible with factory radios with built-in 6-disc
CD changers. Compatible with factory navigation radios.
Make
Mazda
Model
B-series Truck
B-series Truck
Year
1998-2001
1997
Part #
PXDP
PXDP
Harness
Dip Switch Settings*
PXHFD3
2,8 ON
PXHFD2
2,8 ON
IMPORTANT MAZDA APPLICATION INFORMATION
Vehicle Specific Notes
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function.
Make
Mercury
Model
Cougar
Grand Marquis
Grand Marquis
Grand Marquis
Mountaineer
Mountaineer
Mountaineer
Sable
Tracer
Villager
Year
1999-2004
1998-2003
1995-1997
1995-1997
1998-2004
1995-1997
1995-1997
1996-2005
1995-2004
1999-2002
Part #
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
Harness
Dip Switch Settings*
PXHFD4
1,2,8 ON
PXHFD3
2,8 ON
PXHFD2
2,8 ON
PXHFD1
2,8 ON
PXHFD3
2,8 ON
PXHFD2
2,8 ON
PXHFD1
2,8 ON
PXHFD1
2,8 ON
PXHFD1
2,8 ON
PXHFD3
2,8 ON
IMPORTANT MERCURY APPLICATION INFORMATION
Vehicle Specific Notes
*If equipped with JBL, use PXHFD1 at Rear Control Unit in trunk
*If equipped with JBL, use PXHFD1 at Rear Control Unit in trunk
*If equipped with JBL, use PXHFD1 at Rear Control Unit in trunk
*If equipped with JBL, use PXHFD1 at Rear Control Unit in trunk
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function. Not compatible with factory radios with built-in 6-disc
CD changers. Compatible with factory navigation radios.
Make
Nissan
Model
Quest
Year
1999-2002
Part #
PXDP
Harness
Dip Switch Settings*
PXHFD3
2,8 ON
IMPORTANT NISSAN APPLICATION INFORMATION
Vehicle Specific Notes
23
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function.
*Dip Switch Settings: Please See Product Instructions for Dip Switch Configuration Settings
24
Make
Oldsmobile
Model
Achieva
Alero
Alero
Aurora
Aurora
Bravada
Bravada
Cutlass
Cutlass Supreme
Eighty-Eight
Intrigue
LSS
Regency
Silhouette
Silhouette
Year
1996-1998
2003-2004
1999-2000
2001-2004
1995-1999
2004
1997-2001
1997-1999
1995-1997
1996-1999
1998-2001
1996-1999
1997-1998
2004
1996-1999
Part #
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
Harness
Dip Switch Settings*
PXHGM3
1,3,8 ON
PXHGM3
2,3,8 ON
PXHGM2
3,8 ON
PXHGM2
3,8 ON
PXHGM2
3,8 ON
PXHGM3
1,3,8 ON or 2,3,8 ON
PXHGM1
3,8 ON
PXHGM2
3,8 ON
PXHGM2
3,8 ON
PXHGM2
3,8 ON
PXHGM2
3,8 ON
PXHGM2
3,8 ON
PXHGM2
3,8 ON
PXHGM3
2,3,8 ON
PXHGM2
3,8 ON
IMPORTANT OLDSMOBILE APPLICATION INFORMATION
Vehicle Specific Notes
Trunk/CD Changer Mounting Location
Trunk Mounting Location
Trunk Mounting Location
Trunk Mounting Location
Trunk Mounting Location
Trunk Mounting Location
Trunk Mounting Location
Trunk Mounting Location
Trunk Mounting Location
Trunk Mounting Location
Trunk Mounting Location
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function. GM vehicles 1998 – 2004 not equipped with a factory
slave may not be able to support an external device. Therefore the PXDP may not be compatible. If you are an experienced installer, you can retain XM. Please follow this link to the Tech Brief to retain XM:
http://peripheralelectronics.com/web/tech_dept.asp. 1995-1999 Radios with built in CD player (Except Corvette) are NOT compatible because they do not have CD changer control functions.
Make
Plymouth
Model
All Models
Neon
Year
1995-2000
2002-2004
Part #
PXDP
PXDP
Harness
Dip Switch Settings*
PXHCH1
1,4,8 ON
PXHGM3
1,4,8 ON
IMPORTANT PLYMOUTH APPLICATION INFORMATION
Vehicle Specific Notes
All models must have “Disc ^ ” printed on Preset Button # 1.
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function.
Make
Pontiac
Model
Aztec
Bonneville
Bonneville
Firebird / Trans Am
Grand AM
Grand AM
Montana
Montana
Sunfire
Sunfire
TransSport
Vibe
G6
Grand Prix
Year
2003-2005
2000-2005
1996-1999
1996-2002
2003-2005
1996-2000
2004-2005
1999-2000
2003-2005
1996-1999
1996-1998
2004-2005
2005
2004-2007
Part #
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
Not Compatible
Not Compatible
Harness
PXHGM3
PXHGM2
PXHGM1
PXHGM1
PXHGM3
PXHGM1
PXHGM3
PXHGM1
PXHGM3
PXHGM1
PXHGM1
PXHGM3
Dip Switch Settings*
1,3,8 ON or 2,3,8 ON
3,8 ON
3,8 ON
3,8 ON
1,3,8 ON or 2,3,8 ON
3,8 ON
1,3,8 ON or 2,3,8 ON
3,8 ON
1,3,8 ON
3,8 ON
3,8 ON
1,3,8 ON or 2,3,8 ON
Vehicle Specific Notes
Trunk Mounting Location
IMPORTANT PONTIAC APPLICATION INFORMATION
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function. GM vehicles 1998 – 2004 not equipped with a factory
slave may not be able to support an external device. Therefore the PXDP may not be compatible. If you are an experienced installer, you can retain XM. Please follow this link to the Tech Brief to retain XM:
http://peripheralelectronics.com/web/tech_dept.asp. 1995-1999 Radios with built in CD player (Except Corvette) are NOT compatible because they do not have CD changer control functions.
Make
Saturn
Model
All Models
Year
1995-1999
Part #
PXDP
Harness
Dip Switch Settings*
PXHGM1
3,8 ON
IMPORTANT SATURN APPLICATION INFORMATION
Vehicle Specific Notes
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function.
Make
Scion
Model
tC
xA
xB
Year
2003-2007
2003-2005
2003-2005
Part #
PXDP
PXDP
PXDP
Harness
Dip Switch Settings*
Vehicle Specific Notes
PXHTY3
1,2,4,8 ON
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
PXHTY3
1,2,4,8 ON
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
PXHTY3
1,2,4,8 ON
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
IMPORTANT SCION APPLICATION INFORMATION
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function.
Make
Toyota
25
Model
4Runner
4Runner
Avalon
Avalon
Camry
Camry
Celica
Corolla
Corolla
Echo
Highlander
Highlander
Land Cruiser
Land Cruiser
Matrix
Matrix
MR2
RAV4
Sequoia
Sequoia
Sienna
Year
1998-2005
2006-2007
1998-2005
2006-2007
1998-2005
2006-2007
1998-2005
1998-2005
2006-2007
2000-2005
2001-2004
2006-2007
1998-2005
2006-2007
2003-2004
2005-2007
2000-2005
1998-2005
2001-2005
2006-2007
1998-2005
Part #
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
Harness
PXHTY3
PXHTY3 or PXH2TY1
PXHTY3
PXHTY3 or PXH2TY1
PXHTY3
PXHTY3 or PXH2TY1
PXHTY3
PXHTY3
PXHTY3 or PXH2TY1
PXHTY3
PXHTY3
PXHTY3 or PXH2TY1
PXHTY3
PXHTY3 or PXH2TY1
PXHGM3
PXHTY3 or PXH2TY1
PXHTY3
PXHTY3
PXHTY3
PXHTY3 or PXH2TY1
PXHTY3
Dip Switch Settings*
1,2,4,8 ON
1,2,4,8 ON
1,2,4,8 ON
1,2,4,8 ON
1,2,4,8 ON
1,2,4,8 ON
1,2,4,8 ON
1,2,4,8 ON
1,2,4,8 ON
1,2,4,8 ON
1,2,4,8 ON
1,2,4,8 ON
1,2,4,8 ON
1,2,4,8 ON
1,3,8 ON
1,2,4,8 ON
1,2,4,8 ON
1,2,4,8 ON
1,2,4,8 ON
1,2,4,8 ON
1,2,4,8 ON
Vehicle Specific Notes
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
26
Make
Toyota
Model
Sienna
Solara
Solara
Supra
T100
Tacoma
Tacoma
Tercel
Tundra
Prius
Highlander
Year
2006-2007
1999-2005
2006-2007
1998
1998
1998-2005
2006-2007
1998
2000-2007
All Years
2008
Part #
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
Not Compatible
Not Compatible
Harness
PXHTY3 or PXH2TY1
PXHTY3
PXHTY3 or PXH2TY1
PXHTY3
PXHTY3
PXHTY3
PXHTY3 or PXH2TY1
PXHTY3
PXHTY3
Dip Switch Settings*
1,2,4,8 ON
1,2,4,8 ON
1,2,4,8 ON
1,2,4,8 ON
1,2,4,8 ON
1,2,4,8 ON
1,2,4,8 ON
1,2,4,8 ON
1,2,4,8 ON
Vehicle Specific Notes
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
IMPORTANT TOYOTA APPLICATION INFORMATION
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function. When using the PXHTY3 with 2006-2007 vehicles the
green wires must be cut on the PXHTY3 harness. Fully compatible with factory installed Toyota Navigation Systems. Not compatible with Hybrid vehicles.
Make
Volkswagen
Model
All Models
All Models
All Models
Year
1998-2006
1998-2006
2003-2006
Part #
PXDP
PXDP
PXDP
Harness
Dip Switch Settings*
PXHVW1
1,8 ON
PXHVW2
1,8 ON
PXHVW3
1,8 ON
IMPORTANT VOLKSWAGEN APPLICATION INFORMATION
Vehicle Specific Notes
Trunk Mounting Location
For use with Single DIN radios
For use with Double DIN radios
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function. Not compatible with vehicles equipped with a factory
Navigation system. When possible, we recommend using the PXHVW2 or PXHVW3 harness and install the PXDP behind the radio. This will avoid the possibility of inherent noise problems with the factory VW CD changer cable that is found in some vehicles.
Double DIN (4” Tall) VW radios require the PXHVW3 to connect behind the radio.
PXHVW3: When using the PXHVW3 harness, connect the loose black lead to suitable chassis ground. If equipped with factory satellite, remove the blue OEM sub harness from the main OEM harness to plug in the PXHVW3 harness.
Notes
____________________________________________________
_ ____________________________________________________
_ ____________________________________________________
_ ____________________________________________________
_ ____________________________________________________
_ ____________________________________________________
_ ____________________________________________________
_ ____________________________________________________
_ ____________________________________________________
_ ____________________________________________________
_ ____________________________________________________
_ ____________________________________________________
_ ____________________________________________________
_ ____________________________________________________
_ ____________________________________________________
_ ____________________________________________________
_ ____________________________________________________
_ ____________________________________________________
_ ____________________________________________________
_ ____________________________________________________
_ ____________________________________________________
_ ____________________________________________________
_ ____________________________________________________
_ ____________________________________________________
_ ____________________________________________________
_ ____________________________________________________
27
www.isimplesolutions.com
iSimple Solutions®,
a division of AAMP of America™
13160 56th Court Clearwater, Florida 33760
Ph. 866-788-4237
support@isimplesolutions.com
©2009 AAMP of Florida, Inc.
For Best Performance Have It
Professionally Installed.
28
Peripheral iPod Application Guide
Make
Acura
Model
CL
CL
Integra
Integra
Legend
RL
RL
RSX
TL
TL
Vigor
All Models
MDX
SLX
NSX
Year
1998-2000
1996-1997
1998-2001
1992-1997
1992-1995
1998-2002
1996-1997
2002
1999-2002
1996-1997
1992-1994
2003-2007
All Years
All Years
All Years
Part #
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
Not Compatible
Not Compatible
Not Compatible
Not Compatible
Harness
PXHHD1
PXHCH2
PXHHD1
PXHCH2
PXHCH2
PXHHD1
PXHCH2
PXHHD1
PXHHD1
PXHCH2
PXHCH2
Dip Switch Settings**
1,4,8 ON
1,4,8 ON
1,4,8 ON
1,4,8 ON
1,4,8 ON
1,4,8 ON
1,4,8 ON
1,4,8 ON
1,4,8 ON
1,4,8 ON
1,4,8 ON
9/12/2008
Vehicle Specific Notes
IMPORTANT ACURA APPLICATION INFORMATION
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function. Not compatible with factory radios that have an in dash 6 disk cd
changer. Not compatible with navigation radios.
*Dip Switch Settings: Please See Product Instructions for Dip Switch Configuration Settings
Make
Audi
Model
All Models (Except Below)
All Models (Except Below)
A6
A8
Q7
Year
1998-2004
1998-2004
2005-2007
2005-2007
2006-2007
Part #
PXDP
PXDP
OPIAUDI
OPIAUDI
OPIAUDI
Harness
Dip Switch Settings*
PXHAD1
1,8 ON
PXHAD2 + PXHVW2*
1,8 ON
Included
n/a
Included
n/a
Included
n/a
IMPORTANT AUDI APPLICATION INFORMATION
Vehicle Specific Notes
Connect at pre-wired 13-pin cable in the left rear trunk.
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function. Vehicles with Symphony sound systems must use special adapter
harness PXHAD2 as well as PXHVW2 and connect at radio.
OPIAUDI: Replaces factory CD Changer. Does not support video iPods.
*Dip Switch Settings: Please See Product Instructions for Dip Switch Configuration Settings
Make
BMW
Model
3 Series
5 Series
7 Series
Mini
X5
Z3/Z5
Z4
Year
1996-2005
1996-2005
1999-2001
2001-2006
1999-2005
1998-2003
2003-2005
Part #
ISBM71
ISBM71
ISBM71
ISBM71
ISBM71
ISBM71
ISBM71
Harness
Dip Switch Settings*
Included
3,4,8, ON
Included
3,4,8, ON
Included
3,4,8, ON
Included
3,4,8, ON
Included
3,4,8, ON
Included
3,4,8, ON
Included
3,4,8, ON
IMPORTANT BMW APPLICATION INFORMATION
Vehicle Specific Notes
Not Compatible with DSP radios, Trunk Mounting Location
Not Compatible with DSP radios, Trunk Mounting Location
Not Compatible with DSP radios, Trunk Mounting Location
Not Compatible with DSP radios, Trunk Mounting Location
Not Compatible with DSP radios, Trunk Mounting Location
Not Compatible with DSP radios, Trunk Mounting Location
Not Compatible with DSP radios, Trunk Mounting Location
ISBM71: Not Compatible with Factory Head Units with DSP. "DSP" will be indicated on a radio button. Not compatible with vehicles equipped with iDrive.
*Dip Switch Settings: Please See Product Instructions for Dip Switch Configuration Settings
Make
Buick
Model
Century
Century
Enclave
Le Sabre
Lucerne
Park Ave
Rainier
Rainier
Regal
Regal
Rendezvous
Rendezvous
Riviera
Roadmaster
Skylark
Terraza
Allure
LaCrosse
Year
2004-2005
1997-2003
2008
1999-2002
2006-2007
1995-2005
2005
2005
1995-2003
2004
2003-2005
2003-2006
1996-1999
1995-1996
1996-1998
2005-2006
2005
2005
Part #
PXDPGMT
PXDP
PXDP3
PXDP
PXDP3
PXDP
PXDP
PXDPGMT
PXDP
PXDPGMT
PXDP
PXDPGMT
PXDP
PXDP
PXDP
PXDPGMT
Not Compatible
Not Compatible
Harness
PXHGMT
PXHGM1 & GMH32T
PXH3GM1 or PXH3GM1X
PXHGM3
PXH3GM1 or PXH3GM1X
PXHGM1 & GMH32T
PXHGM3
PXHGMT or PXHGMTX
PXHGM1 & GMH32T
PXHGMT
PXHGM3
PXHGMT or PXHGMTX
PXHGM1 & GMH32T
PXHGM1 & GMH32T
PXHGM1 & GMH32T
PXHGMT or PXHGMTX
Dip Switch Settings*
n/a
3,8 ON
n/a
1,3,8 ON
n/a
3,8 ON
1,3,8 ON
n/a
3,8 ON
n/a
1,3,8 ON
n/a
3,8 ON
3,8 ON
3,8 ON
n/a
Vehicle Specific Notes
Must use GMH32T "T"-harness then plug *PXHGM1 behind radio.
XM tuner is on the driver side of the dash tucked high up
Must use GMH32T "T"-harness then plug *PXHGM1 behind radio.
PXHGMTCD harness is required to retain factory CD Changer (if equipped)
Must use GMH32T "T"-harness then plug *PXHGM1 behind radio.
PXHGMTCD harness is required to retain factory CD Changer (if equipped)
PXHGMTCD harness is required to retain factory CD Changer (if equipped)
Must use GMH32T "T"-harness then plug *PXHGM1 behind radio.
Must use GMH32T "T"-harness then plug *PXHGM1 behind radio.
Must use GMH32T "T"-harness then plug *PXHGM1 behind radio.
PXHGMTCD harness is required to retain factory CD Changer (if equipped)
IMPORTANT BUICK APPLICATION INFORMATION
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function. GM vehicles 1998 – 2004 not equipped with a factory slave may not be
able to support an external device. Therefore the PXDP may not be compatible. If you are an experienced installer, you can retain XM. Please follow this link to the Tech Brief to retain XM: http://peripheralelectronics.com/web/tech_dept.asp. 1995-1999 Radios with built in
CD player (Except Corvette) are NOT compatible because they do not have CD changer control functions.
PXDP3: PXH3GM1 is for vehicles without XM, connects to the back of the factory radio. PXH3GM1X harness retains XM and connects to the XM tuner. Non-Navigation radios must have a “CAT” button on the faceplate. Compatible with navigation radios for the applicable
vehicles listed above. Compatible with existing factory CD changer. Not Compatible with 2008 GM vehicles.
PXDPGMT: Radios must be equipped with the "BAND" button and be SAT radio ready. Factory radio must have a CD player and/or tape player. PXHGMTCD harness is required to retain factory CD Changer. PXHGMT harness is for vehicles without XM installed is installed
behind the factory radio. PXHGMTX harness retains XM and is installed at the XM tuner. Rear Seat Entertainment (RSE) will need to be disconnected in order for the PXDPGMT to work properly.
*Dip Switch Settings: Please See Product Instructions for Dip Switch Configuration Settings
Make
Cadillac
Model
Catera
Deville
El Dorado
Escalade
Escalade
Escalade
Escalade
Seville
XLR
Year
2001
1995-2003
1995-2002
1999-2002
2003-2006
2003-2006
2007
1995-2005
2004-2005
Part #
PXDP
PXDP
PXDP
PXDP
PXDP
PXDPGMT
PXDP3
PXDP
PXDPGMT
Harness
Dip Switch Settings*
PXHGM2
3,8 ON
PXHGM2
3,8 ON or 1,3,8 ON
PXHGM2
3,8 ON
PXHGM1
3,8 ON
PXHGM3
1,3,8 ON or 2,3,8 ON
PXHGMT or PXHGMTX
n/a
PXH3GM1 or PXH3GM1X
n/a
PXHGM2
3,8 ON
PXHGMT or PXHGMTX
n/a
IMPORTANT CADILLAC APPLICATION INFORMATION
Vehicle Specific Notes
Behind radio or Trunk Mounting Location
Behind radio or Trunk Mounting Location
Trunk Mounting Location
PXHGMTCD harness is required to retain factory CD Changer (if equipped)
*PLEASE READ IMPORTANT NOTES BELOW
PXHGMTCD harness is required to retain factory CD Changer (if equipped)
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function. GM vehicles 1998 – 2004 not equipped with a factory slave may not be
able to support an external device. Therefore the PXDP may not be compatible. If you are an experienced installer, you can retain XM. Please follow this link to the Tech Brief to retain XM: http://peripheralelectronics.com/web/tech_dept.asp. 1995-1999 Radios with built in
CD player (Except Corvette) are NOT compatible because they do not have CD changer control functions.
PXDP3: PXH3GM1 is for vehicles without XM, connects to the back of the factory radio. PXH3GM1X harness retains XM and connects to the XM tuner. Non-Navigation radios must have a “CAT” button on the faceplate. Compatible with navigation radios for the applicable
vehicles listed above. Compatible with existing factory CD changer. Not Compatible with 2008 GM vehicles. *In some late production 2007 Escalades GM switched to the 2008 model radio, so the PXDP3 may not be compatible in some 2007 Escalades with the new 2008
model year radio.
PXDPGMT: Radios must be equipped with the "BAND" button and be SAT radio ready. Factory radio must have a CD player and/or tape player. PXHGMTCD harness is required to retain factory CD Changer. PXHGMT harness is for vehicles without XM installed is installed
behind the factory radio. PXHGMTX harness retains XM and is installed at the XM tuner. Rear Seat Entertainment (RSE) will need to be disconnected in order for the PXDPGMT to work properly.
*Dip Switch Settings: Please See Product Instructions for Dip Switch Configuration Settings
Make
Chevrolet
Model
Astro Van
Avalanche
Avalanche
Avalanche
Avalanche
Blazer
Camaro
Cavalier
Cavalier
Cavalier
Colorado
Colorado
Corvette
Corvette
Express Van
Impala
Impala
Impala
Impala
Lumina
Malibu
Monte Carlo
Monte Carlo
Monte Carlo
Monte Carlo
Silverado
Silverado
Silverado
Silverado
Suburban
Suburban
Suburban
Suburban
Tahoe
Tahoe
Tahoe
Tahoe
Trailblazer
Trailblazer
Uplander
Venture
Venture
Venture
Year
1996-2005
2002
2003-2006
2003-2006
2007
1998-2002
1997-2002
1996-1999
2003-2005
2003-2005
2005
2004-2006
1997-2004
1997-2004
2003-2005
1995-1999
2000-2005
2003-2005
2006-2007
1996-1999
1997-2000
1995-1999
2000-2005
2003-2005
2006-2007
1996-2002
2003-2006
2003-2006
2007
1995-2002
2003-2006
2003-2006
2007
1995-2002
2003-2006
2003-2006
2007
2002-2007
2003-2007
2005-2006
1997-1999
2004-2005
2003-2006
Part #
PXDP
PXDP
PXDP
PXDPGMT
PXDP3
PXDP
PXDP
PXDP
PXDPGMT
PXDP
PXDP
PXDPGMT
PXDP
PXDP
PXDPGMT
PXDP
PXDP
PXDPGMT
PXDP3
PXDP
PXDP
PXDP
PXDP
PXDPGMT
PXDP3
PXDP
PXDP
PXDPGMT
PXDP3
PXDP
PXDP
PXDPGMT
PXDP3
PXDP
PXDP
PXDPGMT
PXDP3
PXDP
PXDPGMT
PXDPGMT
PXDP
PXDP
PXDPGMT
Harness
Dip Switch Settings*
PXHGM1
3,8 ON
PXHGM1
3,8 ON
PXHGM3
1,3,8 ON
PXHGMT or PXHGMTX
n/a
PXH3GM1 or PXH3GM1X
n/a
PXHGM1
3,8 ON
PXHGM1
3,8 ON
PXHGM1
3,8 ON
PXHGMT or PXHGMTX
n/a
PXHGM3
1,3,8 ON or 2,3,8 ON
PXHGM3
1,3,8 ON
PXHGMT or PXHGMTX
n/a
PXHGM2
3,8 ON
PXHGM4
3,8 ON
PXHGMT or PXHGMTX
n/a
PXHGM1
3,8 ON
PXHGM3
1,3,8 ON
PXHGMT or PXHGMTX
n/a
PXH3GM1 or PXH3GM1X
n/a
PXHGM1
3,8 ON
PXHGM1
3,8 ON
PXHGM1
3,8 ON
PXHGM3
3,8 ON
PXHGMT or PXHGMTX
n/a
PXH3GM1 or PXH3GM1X
n/a
PXHGM1
3,8 ON
PXHGM3
1,3,8 ON
PXHGMT or PXHGMTX
n/a
PXH3GM1 or PXH3GM1X
n/a
PXHGM1
3,8 ON
PXHGM3
1,3,8 ON
PXHGMT or PXHGMTX
n/a
PXH3GM1 or PXH3GM1X
n/a
PXHGM1
3,8 ON
PXHGM3
1,3,8 ON
PXHGMT or PXHGMTX
n/a
PXH3GM1 or PXH3GM1X
n/a
PXHGM3
1,3,8 ON or 2,3,8 ON
PXHGMT or PXHGMTX
n/a
PXHGMT or PXHGMTX
n/a
PXHGM1
3,8 ON
PXHGM3
1,3,8 ON or 2,3,8 ON
PXHGMTX
IMPORTANT CHEVROLET APPLICATION INFORMATION
Vehicle Specific Notes
PXHGMTCD harness is required to retain factory CD Changer (if equipped)
PXHGMTCD harness is required to retain factory CD Changer (if equipped)
PXHGMTCD harness is required to retain factory CD Changer (if equipped)
Trunk Mounting Location
As a substitute, Can also use PXHGM1 and GMH20T Harnesses
PXHGMTCD harness is required to retain factory CD Changer (if equipped)
PXHGMTCD harness is required to retain factory CD Changer (if equipped)
PXHGMTCD harness is required to retain factory CD Changer (if equipped)
PXHGMTCD harness is required to retain factory CD Changer (if equipped)
Not Compatible with Silverado Classic
PXHGMTCD harness is required to retain factory CD Changer (if equipped)
PXHGMTCD harness is required to retain factory CD Changer (if equipped)
PXHGMTCD harness is required to retain factory CD Changer (if equipped)
PXHGMTCD harness is required to retain factory CD Changer (if equipped)
PXHGMTCD harness is required to retain factory CD Changer (if equipped)
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function. GM vehicles 1998 – 2004 not equipped with a factory slave may not be
able to support an external device. Therefore the PXDP may not be compatible. If you are an experienced installer, you can retain XM. Please follow this link to the Tech Brief to retain XM: http://peripheralelectronics.com/web/tech_dept.asp. 1995-1999 Radios with built in
CD player (Except Corvette) are NOT compatible because they do not have CD changer control functions.
PXDP3: PXH3GM1 is for vehicles without XM, connects to the back of the factory radio. PXH3GM1X harness retains XM and connects to the XM tuner. Non-Navigation radios must have a “CAT” button on the faceplate. Compatible with navigation radios for the applicable
vehicles listed above. Compatible with existing factory CD changer. Not Compatible with 2008 GM vehicles.
PXDPGMT: Radios must be equipped with the "BAND" button and be SAT radio ready. Factory radio must have a CD player and/or tape player. PXHGMTCD harness is required to retain factory CD Changer. PXHGMT harness is for vehicles without XM installed is installed
behind the factory radio. PXHGMTX harness retains XM and is installed at the XM tuner. Rear Seat Entertainment (RSE) will need to be disconnected in order for the PXDPGMT to work properly.
*Dip Switch Settings: Please See Product Instructions for Dip Switch Configuration Settings
Make
Chrysler
Model
All Models (Except Below)
All Models
All Models
300
Aspen
Pacifica
PT Cruiser
Sebring
Year
2002-2005
1999--2001
1995-1999*
2005-2007
2007
2006
2007-2008
2006
Part #
PXDP
PXDP
PXDP
CHYP
CHYP
PXDP
CHYP
PXDP
Harness
Dip Switch Settings*
Vehicle Specific Notes
Must be non-CANBUS, if radio is an REF,REC,RAQ, RAK series, vehicles are not compatible
PXHCH3
4,8 ON
PXHCH2
4,8 ON
*1999 Radios with rounded corners use PXHCH2
PXHCH1
1,4,8 ON
*1999 Radios with square corners use PXHCH1
Included
n/a
Included
n/a
PXHCH3
4,8 ON
Included
n/a
PXHCH3
4,8 ON
IMPORTANT CHRYSLER APPLICATION INFORMATION
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function. To determine if your 2002-2005 vehicle is compatible, factory radio
must have "Disk ^" on preset 1. Vehicle must be non-CANBUS, if radio is an REF,REC,RAQ, RAK series, vehicles are not compatible. The series is indicated on the front of the radio. 1999 Chrysler vehicles have one of two different style radios. These two radios use
different harnesses. The shape of the radio face will determine which harness you will use. If your radio face is SQUARE, you will use the harness part# PXHCH1. If your radio face is OVAL (rounded corners), you will use the harness part# PXHCH2.
CHYP: Not compatible with REF model factory radios. Model is indicated on the face of the factory radio. Compatible with RAQ, REC, and RAK series factory radios. If the vehicle has a VES (Video Entertainment System), it must be disconnected. The audio from the VES will
no longer play through the factory stereo, but the video and wireless headphones will still function normally. VES does NOT operate in R.A.P. mode, the radio will automatically switch from the CHYP to tuner mode during R.A.P. (Retained Accessory Power). Compatible with
factory installed satellite.
*Dip Switch Settings: Please See Product Instructions for Dip Switch Configuration Settings
Make
Dodge
Model
All Models (Except Below)
All Models
All Models
Caliber
Charger
Dakota
Durango
Magnum
Ram
Year
2002-2005
1999*-2001
1995-1999*
2006-2008
2005-2007
2005-2007
2004-2007
2005-2007
2006-2008
Part #
PXDP
PXDP
PXDP
CHYP
CHYP
CHYP
CHYP
CHYP
CHYP
Harness
Dip Switch Settings*
PXHCH3
4,8 ON
PXHCH2
4,8 ON
PXHCH1
1,4,8 ON
Included
n/a
Included
n/a
Included
n/a
Included
n/a
Included
n/a
Included
n/a
IMPORTANT DODGE APPLICATION INFORMATION
Vehicle Specific Notes
Must be non-CANBUS, if radio is an REF,REC,RAQ, RAK series, vehicles are not compatible
*1999 Radios with rounded corners use PXHCH2
*1999 Radios with square corners use PXHCH1
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function. To determine if your 2002-2005 vehicle is compatible, factory radio
must have "Disk ^" on preset 1. Vehicle must be non-CANBUS, if radio is an REF,REC,RAQ, RAK series, vehicles are not compatible. The series is indicated on the front of the radio. 1999 Chrysler vehicles have one of two different style radios. These two radios use
different harnesses. The shape of the radio face will determine which harness you will use. If your radio face is SQUARE, you will use the harness part# PXHCH1. If your radio face is OVAL (rounded corners), you will use the harness part# PXHCH2.
CHYP:Not compatible with REF model factory radios. Model is indicated on the face of the factory radio. Compatible with RAQ, REC, and RAK series factory radios. If the vehicle has a VES (Video Entertainment System), it must be disconnected. The audio from the VES will
no longer play through the factory stereo, but the video and wireless headphones will still function normally. VES does NOT operate in R.A.P. mode, the radio will automatically switch from the CHYP to tuner mode during R.A.P. (Retained Accessory Power). Compatible with
factory installed satellite.
*Dip Switch Settings: Please See Product Instructions for Dip Switch Configuration Settings
Make
Eagle
Model
All Models
Year
1995-1998
Part #
PXDP
Harness
Dip Switch Settings*
PXHCH1
1,4,8 ON
IMPORTANT EAGLE APPLICATION INFORMATION
Vehicle Specific Notes
All models must have “Disc ^ ” printed on Preset Button # 1.
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function. If your vehicle is equipped with a factory CD changer, you must
disconnect it in order to be able to install the interface. You will lose the use of the factory CD changer to gain use of your iPod.
*Dip Switch Settings: Please See Product Instructions for Dip Switch Configuration Settings
Make
Ford
Model
Crown Victoria
Crown Victoria
Crown Victoria
Edge
Escape
Escape
Econoline
Econoline
Escort
Excursion
Expedition
Expedition
Expedition
Explorer
Explorer
Explorer
Explorer
Explorer
Freestar
Freestyle
F-150
F-150
F-250
Year
1998-2003
1995-1997
1995-1997
2007-2008
2001-2004
2008
1998-2004
1997
1997-2004
2000-2004
2007-2008
1999-2002
1997-1998
2005-2007
2006-2008
1998-2004
1995-1997
1995-1997
2004
2005-2007
2005-2008
2005-2007
2007-2008
Part #
PXDP
PXDP
PXDP
PXAMG
PXDP
PXAMG
PXDP
PXDP
PXDP
PXDP
PXAMG
PXDP
PXDP
PXDP2
PXAMG
PXDP
PXDP
PXDP
PXDP
PXDP2
PXAMG
PXDP2
PXAMG
Harness
PXHFD3
PXHFD2
PXHFD1
PGHFD1
PXHFD3
PGHFD1
PXHFD3
PXHFD2
PXHFD2
PXHFD3
PGHFD1
PXHFD3
PXHFD2
PXH2FD1
PGHFD1
PXHFD3
PXHFD2
PXHFD1
PXHFD3
PXH2FD1
PGHFD1
PXH2FD1
PGHFD1
Dip Switch Settings*
2,8 ON
2,8 ON
2,8 ON
Vehicle Specific Notes
*If equipped with JBL, use PXHFD1 at Rear Control Unit in trunk
2,8 ON
Also requires PGHFD1A for Separate LCD Display. Not needed for navigation radios.
2,8 ON
2,8 ON
2,8 ON
2,8 ON
2,8 ON
2,8 ON
1,2,3 ON
2,8 ON
2,8 ON
2,8 ON
2,8 ON
1,2,3 ON
1,2,3 ON
*If equipped with JBL, use PXHFD1 at Rear Control Unit in trunk
F-250
F-350
F-350
F-450
F-series Pick Up
F-series Pick Up
Five Hundred
Five Hundred
Focus
Focus
Freestyle
Fusion
Fusion
Mustang
Mustang
Ranger
Ranger
Sport Trac
Sport Trac
Sport Trac
Taurus
Taurus
Taurus X
Thunderbird
Windstar
All
2007
2007-2008
2007
2007-2008
1998-2003
1995-1997
2006-2007
2005-2007
2005-2007
2000-2003
2006-2007
2005-2008
2006-2007
2005-2008
2001-2003
1998-2004
1995-1997
2007-2008
2007
2000-2004
2008
1996-2005
2008
2000-2004
1999-2004
2008
PXDP2
PXAMG
PXDP2
PXAMG
PXDP
PXDP
PXAMG
PXDP2
PXAMG
PXDP
PXAMG
PXAMG
PXDP2
PXAMG
PXDP
PXDP
PXDP
PXAMG
PXDP2
PXDP
PXAMG
PXDP
PXAMG
PXDP
PXDP
PXDP2
PXH2FD1
1,2,3 ON
PGHFD1
PXH2FD1
1,2,3 ON
PGHFD1
PXHFD3
2,8 ON
PXHFD2
2,8 ON
PGHFD1
PXH2FD1
1,2,3 ON
PGHFD1
PXHFD4
2,8 ON
PGHFD1
PGHFD1
PXH2FD1
1,2,3 ON
PGHFD1
PXHFD3
2,8 ON
PXHFD3
2,8 ON
PXHFD2
2,8 ON
PGHFD1
PXH2FD1
1,2,3 ON
PXHFD3
2,8 ON
PGHFD1
PXHFD1
2,8 ON
PGHFD1
PXHFD3
2,8 ON
PXHFD3
2,8 ON
N/A
IMPORTANT FORD APPLICATION INFORMATION
See Important F-250 Compatibility Notes Below
See Important F-350 Compatibility Notes Below
Not compatible with factory installed Blaupunkt radio
Sat Tuner located high in the passenger kick panel
Trunk Mounting Location
ALL 2008 Models are NOT Compatible with the PXDP2
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function. Not compatible with factory radios with built-in 6-disc CD changers.
Compatible with factory navigation radios.
PXDP2: Not compatible with Factory Satellite or Rear Seat Entertainment systems, they must be disconnected for the PXDP2 to operate correctly. Radio must be MP3 compatible, this will be indicated on the face of the radio. Compatible with factory navigation radios. ALL
2008 Models are NOT Compatible with the PXDP2. 250 and F-350: Compatible with factory radios that respond with the text "NO AUX AUDIO" when the Aux button on the factory radio pushed before the interface is installed. If the text displays "NO AUX" the PXDP2 is not
compatible.
PXAMG: Not compatible with SYNC.
*Dip Switch Settings: Please See Product Instructions for Dip Switch Configuration Settings
Make
GMC
Model
Acadia
Canyon
Envoy
Envoy
Envoy
Denali
Denali
Denali
Denali
Jimmy
Sonoma
Safari
Savana
Savana
Sierra
Sierra
Sierra
Sierra
Sonoma
Suburban
Suburban
Suburban
Suburban
Yukon/XL
Yukon/XL
Yukon/XL
Yukon/XL
Year
2007
2004-2006
1999-2001
2003-2007
2002-2007
1995-2002
2003-2006
2003-2006
2007
1998-2002
1998-2002
1996-2005
1999-2000
2003-2006
1995-2002
2003-2006
2003-2006
2007
2003-2004
1995-2002
2003-2006
2003-2006
2007
1995-2002
2003-2006
2003-2006
2007
Part #
PXDP3
PXDPGMT
PXDP
PXDPGMT
PXDP
PXDP
PXDP
PXDPGMT
PXDP3
PXDP
PXDP
PXDP
PXDP
PXDPGMT
PXDP
PXDP
PXDPGMT
PXDP3
PXDPGMT
PXDP
PXDP
PXDPGMT
PXDP3
PXDP
PXDP
PXDPGMT
PXDP3
Harness
Dip Switch Settings*
PXH3GM1 or PXH3GM1X
n/a
PXHGMT or PXHGMTX
3,8 ON
PXHGM1
3,8 ON
PXHGMT or PXHGMTX
n/a
PXHGM3
1,3,8 ON or 2,3,8 ON
PXHGM1
3,8 ON
PXHGM3
1,3,8 ON
PXHGMT or PXHGMTX
n/a
PXH3GM1 or PXH3GM1X
n/a
PXHGM1
3,8 ON
PXHGM1
3,8 ON
PXHGM1
3,8 ON
PXHGM1
3,8 ON
PXHGMT or PXHGMTX
n/a
PXHGM1
3,8 ON
PXHGM3
1,3,8 ON
PXHGMT or PXHGMTX
n/a
PXH3GM1 or PXH3GM1X
n/a
PXHGMT or PXHGMTX
n/a
PXHGM1
3,8 ON
PXHGM3
1,3,8 ON
PXHGMT or PXHGMTX
PXH3GM1 or PXH3GM1X
n/a
PXHGM1
3,8 ON
PXHGM3
1,3,8 ON
PXHGMT or PXHGMTX
n/a
PXH3GM1 or PXH3GM1X
n/a
IMPORTANT GMC APPLICATION INFORMATION
Vehicle Specific Notes
XM tuner is located behind the rear driver’s side quarter panel
PXHGMTCD harness is required to retain factory CD Changer (if equipped)
PXHGMTCD harness is required to retain factory CD Changer (if equipped)
PXHGMTCD harness is required to retain factory CD Changer (if equipped)
PXHGMTCD harness is required to retain factory CD Changer (if equipped)
PXHGMTCD harness is required to retain factory CD Changer (if equipped)
Not Compatible with Sierra Classic
PXHGMTCD harness is required to retain factory CD Changer (if equipped)
PXHGMTCD harness is required to retain factory CD Changer (if equipped)
PXHGMTCD harness is required to retain factory CD Changer (if equipped)
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function. GM vehicles 1998 – 2004 not equipped with a factory slave may not be
able to support an external device. Therefore the PXDP may not be compatible. If you are an experienced installer, you can retain XM. Please follow this link to the Tech Brief to retain XM: http://peripheralelectronics.com/web/tech_dept.asp. 1995-1999 Radios with built in
CD player (Except Corvette) are NOT compatible because they do not have CD changer control functions.
PXDP3: PXH3GM1 is for vehicles without XM, connects to the back of the factory radio. PXH3GM1X harness retains XM and connects to the XM tuner. Non-Navigation radios must have a “CAT” button on the faceplate. Compatible with navigation radios for the applicable
vehicles listed above. Compatible with existing factory CD changer. Not Compatible with 2008 GM vehicles.
PXDPGMT: Radios must be equipped with the "BAND" button and be SAT radio ready. Factory radio must have a CD player and/or tape player. PXHGMTCD harness is required to retain factory CD Changer. PXHGMT harness is for vehicles without XM installed is installed
behind the factory radio. PXHGMTX harness retains XM and is installed at the XM tuner. Rear Seat Entertainment (RSE) will need to be disconnected in order for the PXDPGMT to work properly.
*Dip Switch Settings: Please See Product Instructions for Dip Switch Configuration Settings
Make
Model
Year
Part #
Harness
Dip Switch Settings*
Vehicle Specific Notes
Honda
Accord
Accord
Civic
Civic
CRV
CRV
Del Sol
Element
Insight
Odyssey
Odyssey
Passport
Prelude
Prelude
S2000
All Models
Accord
Pilot
Ridgeline
S2000
1998-2002
1992-1997
1998-2004
1992-1997
1998-2004
1997
1993-1997
2002
2001-2004
1995-1997
1998-2004
1998-2002
1998-2001
1992-1997
2000-2003
2005-2007
2003-2004
All Years
All Years
2004
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
Not Compatible
Not Compatible
Not Compatible
Not Compatible
Not Compatible
PXHHD1
PXHCH2
PXHHD1
PXHCH2
PXHHD1
PXHCH2
PXHCH2
PXHHD1
PXHHD1
PXHCH2
PXHHD1
PXHHD1
PXHHD1
PXHCH2
PXHHD1
1,4,8 ON
1,4,8 ON
1,4,8 ON
1,4,8 ON
1,4,8 ON
1,4,8 ON
1,4,8 ON
1,4,8 ON
1,4,8 ON
1,4,8 ON
1,4,8 ON
1,2,4,8 ON
1,4,8 ON
1,4,8 ON
1,4,8 ON
IMPORTANT HONDA APPLICATION INFORMATION
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function. Not compatible with factory radios that have an in dash 6 disk cd
changer. Not compatible with navigation radios.
*Dip Switch Settings: Please See Product Instructions for Dip Switch Configuration Settings
Make
Hummer
Model
H2
H2
H3
Year
2003-2006
2003-2007
2005
Part #
PXDP
PXDPGMT
PXDP
Harness
Dip Switch Settings*
Vehicle Specific Notes
PXHGM3
1,3,8 ON or 2,3,8 ON
*2003-2005 Must disable factory XM Tuner if equipped
PXHGMT or PXHGMTX
n/a
PXHGMTCD harness is also required to retain factory CD Changer (if equipped)
PXHGM3
1,3,8 ON or 2,3,8 ON
IMPORTANT HUMMER APPLICATION INFORMATION
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function.
PXDPGMT: Radios must be equipped with the "BAND" button and be SAT radio ready. Factory radio must have a CD player and/or tape player. PXHGMTCD harness is required to retain factory CD Changer. PXHGMT harness is for vehicles without XM installed is installed
behind the factory radio. PXHGMTX harness retains XM and is installed at the XM tuner. Rear Seat Entertainment (RSE) will need to be disconnected in order for the PXDPGMT to work properly.
*Dip Switch Settings: Please See Product Instructions for Dip Switch Configuration Settings
Make
Isuzu
Model
Amigo
Rodeo
Trooper
Year
1998-2002
1998-2002
1998-2002
Part #
PXDP
PXDP
PXDP
Harness
Dip Switch Settings*
PXHTY3
1,2,4,8 ON
PXHTY3
1,2,4,8 ON
PXHTY3
1,2,4,8 ON
IMPORTANT ISUZU APPLICATION INFORMATION
Vehicle Specific Notes
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function.
*Dip Switch Settings: Please See Product Instructions for Dip Switch Configuration Settings
Make
Jaguar
Model
S-Type
Year
2000-2002
Part #
PXDP
Harness
Dip Switch Settings*
PXHFD4
2,8 ON
IMPORTANT JAGUAR APPLICATION INFORMATION
Vehicle Specific Notes
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function.
*Dip Switch Settings: Please See Product Instructions for Dip Switch Configuration Settings
Make
Jeep
Model
All Models
All Models
All Models
Grand Cherokee
Commander
Compass
Patriot
Year
2002-2005
1999*-2001
1995-1999*
2005-2007
2005-2007
2007-2008
2007-2008
Part #
PXDP
PXDP
PXDP
CHYP
CHYP
CHYP
CHYP
Harness
Dip Switch Settings*
PXHCH3
4,8 ON
PXHCH2
4,8 ON
PXHCH1
1,4,8 ON
Included
n/a
Included
n/a
Included
n/a
Included
n/a
IMPORTANT JEEP APPLICATION INFORMATION
Vehicle Specific Notes
Must be non-CANBUS, if radio is an REF,REC,RAQ, RAK series, vehicles are not compatible
*1999 Radios with rounded corners use PXHCH2
*1999 Radios with square corners use PXHCH1
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function. To determine if your 2002-2005 vehicle is compatible, factory radio
must have "Disk ^" on preset 1. Vehicle must be non-CANBUS, if radio is an REF,REC,RAQ, RAK series, vehicles are not compatible. The series is indicated on the front of the radio. 1999 Chrysler vehicles have one of two different style radios. These two radios use
different harnesses. The shape of the radio face will determine which harness you will use. If your radio face is SQUARE, you will use the harness part# PXHCH1. If your radio face is OVAL (rounded corners), you will use the harness part# PXHCH2.
CHYP: Not compatible with REF model factory radios. Model is indicated on the face of the factory radio. Compatible with RAQ, REC, and RAK series factory radios. If the vehicle has a VES (Video Entertainment System), it must be disconnected. The audio from the VES will
no longer play through the factory stereo, but the video and wireless headphones will still function normally. VES does NOT operate in R.A.P. mode, the radio will automatically switch from the CHYP to tuner mode during R.A.P. (Retained Accessory Power). Compatible with
factory installed satellite.
*Dip Switch Settings: Please See Product Instructions for Dip Switch Configuration Settings
Make
Lexus
Model
ES330
GS300
Year
2005
2006
Part #
PXDP2
PXDP2
Harness
Dip Switch Settings*
PXH2TY1
2,4 ON
PXH2TY1
2,4 ON
IMPORTANT LEXUS APPLICATION INFORMATION
Vehicle Specific Notes
PXDP2: Radio must have a button labeled "SAT". Fully compatible with factory installed Lexus Navigation Systems. Not compatible with factory satellite. If satellite is installed, it must be disconnected. Not compatible with Hybrid vehicles.
*Dip Switch Settings: Please See Product Instructions for Dip Switch Configuration Settings
Make
Lincoln
Model
Aviator
Continental
Year
2002-2003
1998-2004
Part #
PXDP
PXDP
Harness
PXHFD3
PXHFD3
Dip Switch Settings*
2,8 ON
2,8 ON
Vehicle Specific Notes
Continental
Continental*
LS
Mark VIII
Mark LT
Mark LT
MKZ
MKX
Navigator
Navigator
Navigator
Town Car
Town Car
Town Car*
Zephyr
All
1995-1997
1995-1997
2000-2003
1995-1998
2006-2008
2005-2006
2007-2008
2007-2008
2007-2008
1999-2003
1997-1998
1998-2003
1995-1997
1995-1997
2005-2006
2008
PXDP
PXDP
PXDP
PXDP
PXAMG
PXDP2
PXAMG
PXAMG
PXAMG
PXDP
PXDP
PXDP
PXDP
PXDP
PXAMG
PXDP2
PXHFD2
2,8 ON
PXHFD1
2,8 ON
PXHFD3
2,8 ON
PXHFD2
2,8 ON
PGHFD1
PXH2FD1
1,2,3 ON
PGHFD1
PGHFD1
PGHFD1
PXHFD3
2,8 ON
PXHFD2
2,8 ON
PXHFD3
2,8 ON
PXHFD2
2,8 ON
PXHFD1
2,8 ON
PGHFD1
N/A
IMPORTANT LINCOLN APPLICATION INFORMATION
*If equipped with JBL, use PXHFD1 at Rear Control Unit in trunk
*If equipped with JBL, use PXHFD1 at Rear Control Unit in trunk
ALL 2008 Models are NOT Compatible with the PXDP2
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function. Not compatible with factory radios with built-in 6-disc CD changers.
Compatible with factory navigation radios.
PXDP2: Not compatible with Factory Satellite or Rear Seat Entertainment systems, they must be disconnected for the PXDP2 to operate correctly. Radio must be MP3 compatible, this will be indicated on the face of the radio. Compatible with factory navigation radios. ALL
2008 Models are NOT Compatible with the PXDP2
PXAMG: Not compatible with SYNC.
*Dip Switch Settings: Please See Product Instructions for Dip Switch Configuration Settings
Make
Mazda
Model
B-series Truck
B-series Truck
Year
1998-2001
1997
Part #
PXDP
PXDP
Harness
Dip Switch Settings*
PXHFD3
2,8 ON
PXHFD2
2,8 ON
IMPORTANT MAZDA APPLICATION INFORMATION
Vehicle Specific Notes
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function.
*Dip Switch Settings: Please See Product Instructions for Dip Switch Configuration Settings
Make
Mercedes Benz
Model
C
CL
CLK
CLS
E
GL
Maybach
ML
R
SL
SLK
Year
2005-2007
2004-2007
2004-2007
2005-2007
2003-2007
2007
2004-2007
2006-2007
2006-2007
2006-2007
2005-2007
Part #
Opi-M
Opi-M
Opi-M
Opi-M
Opi-M
Opi-M
Opi-M
Opi-M
Opi-M
Opi-M
Opi-M
Harness
Dip Switch Settings*
Included
n/a
Included
n/a
Included
n/a
Included
n/a
Included
n/a
Included
n/a
Included
n/a
Included
n/a
Included
n/a
Included
n/a
Included
n/a
IMPORTANT MERCURY APPLICATION INFORMATION
Vehicle Specific Notes
Opi-M: Must disconnect factory CD changer. Must be a Navigation Radio
Opi-M: Must be a MOST Databus vehicle
Make
Mercury
Model
Cougar
Grand Marquis
Grand Marquis
Grand Marquis
Mariner
Milan
Montego
Montego
Mountaineer
Mountaineer
Mountaineer
Mountaineer
Sable
Sable
Tracer
Villager
All
Year
1999-2004
1998-2003
1995-1997
1995-1997
2008
2006-2008
2005-2007
2005-2006
2006-2008
1998-2004
1995-1997
1995-1997
2008
1996-2005
1995-2004
1999-2002
2008
Part #
PXDP
PXDP
PXDP
PXDP
PXAMG
PXAMG
PXAMG
PXDP2
PXAMG
PXDP
PXDP
PXDP
PXAMG
PXDP
PXDP
PXDP
PXDP2
Harness
Dip Switch Settings*
Vehicle Specific Notes
PXHFD4
1,2,8 ON
PXHFD3
2,8 ON
PXHFD2
2,8 ON
PXHFD1
2,8 ON
*If equipped with JBL, use PXHFD1 at Rear Control Unit in trunk
PGHFD1
Also requires PGHFD1A for Separate LCD Display. Not needed for navigation radios.
PGHFD1
PGHFD1
PXH2FD1
1,2,3 ON
PGHFD1
PXHFD3
2,8 ON
PXHFD2
2,8 ON
PXHFD1
2,8 ON
*If equipped with JBL, use PXHFD1 at Rear Control Unit in trunk
PGHFD1
PXHFD1
2,8 ON
*If equipped with JBL, use PXHFD1 at Rear Control Unit in trunk
PXHFD1
2,8 ON
*If equipped with JBL, use PXHFD1 at Rear Control Unit in trunk
PXHFD3
2,8 ON
N/A
ALL 2008 Models are NOT Compatible with the PXDP2
IMPORTANT MERCURY APPLICATION INFORMATION
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function. Not compatible with factory radios with built-in 6-disc CD changers.
Compatible with factory navigation radios.
PXDP2: Not compatible with Factory Satellite or Rear Seat Entertainment systems, they must be disconnected for the PXDP2 to operate correctly. Radio must be MP3 compatible, this will be indicated on the face of the radio. Compatible with factory navigation radios. ALL
2008 Models are NOT Compatible with the PXDP2
PXAMG: Not compatible with SYNC.
*Dip Switch Settings: Please See Product Instructions for Dip Switch Configuration Settings
Make
Nissan
Model
Quest
Year
1999-2002
Part #
PXDP
Harness
PXHFD3
Dip Switch Settings*
2,8 ON
Vehicle Specific Notes
IMPORTANT NISSAN APPLICATION INFORMATION
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function.
*Dip Switch Settings: Please See Product Instructions for Dip Switch Configuration Settings
Make
Oldsmobile
Model
Achieva
Alero
Alero
Alero
Aurora
Aurora
Bravada
Bravada
Bravada
Cutlass
Cutlass Supreme
Eighty-Eight
Intrigue
LSS
Regency
Silhouette
Silhouette
Silhouette
Year
1996-1998
2003-2004
2003-2004
1999-2000
2001-2004
1995-1999
2004
2003-2004
1997-2001
1997-1999
1995-1997
1996-1999
1998-2001
1996-1999
1997-1998
2004
2003-2004
1996-1999
Part #
PXDP
PXDP
PXDPGMT
PXDP
PXDP
PXDP
PXDP
PXDPGMT
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP
PXDPGMT
PXDP
Harness
Dip Switch Settings*
Vehicle Specific Notes
PXHGM3
1,3,8 ON
Trunk/CD Changer Mounting Location
PXHGM3
2,3,8 ON
PXHGMT or PXHGMTX
n/a
PXHGMTCD harness is required to retain factory CD Changer (if equipped)
PXHGM2
3,8 ON
Trunk Mounting Location
PXHGM2
3,8 ON
Trunk Mounting Location
PXHGM2
3,8 ON
Trunk Mounting Location
PXHGM3
1,3,8 ON or 2,3,8 ON
PXHGMT or PXHGMTX
n/a
PXHGMTCD harness is required to retain factory CD Changer (if equipped)
PXHGM1
3,8 ON
PXHGM2
3,8 ON
Trunk Mounting Location
PXHGM2
3,8 ON
Trunk Mounting Location
PXHGM2
3,8 ON
Trunk Mounting Location
PXHGM2
3,8 ON
Trunk Mounting Location
PXHGM2
3,8 ON
Trunk Mounting Location
PXHGM2
3,8 ON
Trunk Mounting Location
PXHGM3
2,3,8 ON
PXHGMT
n/a
PXHGMTCD harness is required to retain factory CD Changer (if equipped)
PXHGM2
3,8 ON
Trunk Mounting Location
IMPORTANT OLDSMOBILE APPLICATION INFORMATION
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function. GM vehicles 1998 – 2004 not equipped with a factory slave may not be
able to support an external device. Therefore the PXDP may not be compatible. If you are an experienced installer, you can retain XM. Please follow this link to the Tech Brief to retain XM: http://peripheralelectronics.com/web/tech_dept.asp. 1995-1999 Radios with built in
CD player (Except Corvette) are NOT compatible because they do not have CD changer control functions.
PXDPGMT: Radios must be equipped with the "BAND" button and be SAT radio ready. Factory radio must have a CD player and/or tape player. PXHGMTCD harness is required to retain factory CD Changer. PXHGMT harness is for vehicles without XM installed is installed
behind the factory radio. PXHGMTX harness retains XM and is installed at the XM tuner. Rear Seat Entertainment (RSE) will need to be disconnected in order for the PXDPGMT to work properly.
*Dip Switch Settings: Please See Product Instructions for Dip Switch Configuration Settings
Make
Plymouth
Model
All Models
Neon
Year
1995-2000
2002-2004
Part #
PXDP
PXDP
Harness
Dip Switch Settings*
PXHCH1
1,4,8 ON
PXHGM3
1,4,8 ON
IMPORTANT PLYMOUTH APPLICATION INFORMATION
Vehicle Specific Notes
All models must have “Disc ^ ” printed on Preset Button # 1.
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function.
*Dip Switch Settings: Please See Product Instructions for Dip Switch Configuration Settings
Make
Pontiac
Model
Aztec
Aztec
Bonneville
Bonneville
Firebird / Trans Am
Grand AM
Grand AM
Grand AM
Montana
Montana
Montana
Sunfire
Sunfire
Sunfire
TransSport
Vibe
G6
Grand Prix
Year
2003-2005
2003-2006
2000-2005
1996-1999
1996-2002
2003-2005
2003-2006
1996-2000
2004-2005
2003-2005
1999-2000
2003-2005
2003-2005
1996-1999
1996-1998
2004-2005
2005
2004-2007
Part #
PXDP
PXDPGMT
PXDP
PXDP
PXDP
PXDP
PXDPGMT
PXDP
PXDP
PXDPGMT
PXDP
PXDP
PXDPGMT
PXDP
PXDP
PXDP
Not Compatible
Not Compatible
Harness
PXHGM3
PXHGMT or PXHGMTX
PXHGM2
PXHGM1
PXHGM1
PXHGM3
PXHGMT or PXHGMTX
PXHGM1
PXHGM3
PXHGMT or PXHGMTX
PXHGM1
PXHGM3
PXHGMT or PXHGMTX
PXHGM1
PXHGM1
PXHGM3
Dip Switch Settings*
1,3,8 ON or 2,3,8 ON
n/a
3,8 ON
3,8 ON
3,8 ON
1,3,8 ON or 2,3,8 ON
n/a
3,8 ON
1,3,8 ON or 2,3,8 ON
n/a
3,8 ON
1,3,8 ON
n/a
3,8 ON
3,8 ON
1,3,8 ON or 2,3,8 ON
Vehicle Specific Notes
PXHGMTCD harness is required to retain factory CD Changer (if equipped)
Trunk Mounting Location
PXHGMTCD harness is required to retain factory CD Changer (if equipped)
PXHGMTCD harness is required to retain factory CD Changer (if equipped)
PXHGMTCD harness is required to retain factory CD Changer (if equipped)
IMPORTANT PONTIAC APPLICATION INFORMATION
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function. GM vehicles 1998 – 2004 not equipped with a factory slave may not be
able to support an external device. Therefore the PXDP may not be compatible. If you are an experienced installer, you can retain XM. Please follow this link to the Tech Brief to retain XM: http://peripheralelectronics.com/web/tech_dept.asp. 1995-1999 Radios with built in
CD player (Except Corvette) are NOT compatible because they do not have CD changer control functions.
PXDPGMT:Radios must be equipped with the "BAND" button and be SAT radio ready. Factory radio must have a CD player and/or tape player. PXHGMTCD harness is required to retain factory CD Changer. PXHGMT harness is for vehicles without XM installed is installed
behind the factory radio. PXHGMTX harness retains XM and is installed at the XM tuner. Rear Seat Entertainment (RSE) will need to be disconnected in order for the PXDPGMT to work properly.
*Dip Switch Settings: Please See Product Instructions for Dip Switch Configuration Settings
Make
Porsche
Model
All Models with Navigation
All Models with Navigation
Year
2005-2007
2004
Part #
OPIP
OPIP04
Harness
Dip Switch Settings*
Included
n/a
Included
n/a
IMPORTANT PONTIAC APPLICATION INFORMATION
Vehicle Specific Notes
Must be a MOST Databus vehicle
Must be a MOST Databus vehicle
OPIP/OPIP04: Must disconnect factory CD changer. Must be a Navigation Radio
Make
Saturn
Model
All Models
Outlook
Year
1995-1999
2007
Part #
PXDP
PXDP3
Harness
Dip Switch Settings*
PXHGM1
3,8 ON
PXH3GM1 or PXH3GM1X
n/a
IMPORTANT SATURN APPLICATION INFORMATION
Vehicle Specific Notes
XM tuner is on the driver side of the dash tucked high up
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function.
PXDP3: PXH3GM1 is for vehicles without XM, connects to the back of the factory radio. PXH3GM1X harness retains XM and connects to the XM tuner. Non-Navigation radios must have a “CAT” button on the faceplate. Compatible with navigation radios for the applicable
vehicles listed above. Compatible with existing factory CD changer. Not Compatible with 2008 GM vehicles.
*Dip Switch Settings: Please See Product Instructions for Dip Switch Configuration Settings
Make
Scion
Model
tC
xA
xB
Year
2003-2007
2003-2005
2003-2005
Part #
PXDP
PXDP
PXDP
Harness
Dip Switch Settings*
PXHTY3
1,2,4,8 ON
PXHTY3
1,2,4,8 ON
PXHTY3
1,2,4,8 ON
IMPORTANT SCION APPLICATION INFORMATION
Vehicle Specific Notes
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function.
*Dip Switch Settings: Please See Product Instructions for Dip Switch Configuration Settings
Make
Suzuki
Model
XL-7
Year
2007
Part #
PXDP3
Harness
Dip Switch Settings*
PXH3GM1 or PXH3GM1X
n/a
IMPORTANT SCION APPLICATION INFORMATION
Vehicle Specific Notes
PXDP3: Non-Navigation radios must have a “CAT” button on the faceplate. Compatible with all navigation radios. Compatible with existing factory CD changer. PXH3GM1 is for vehicles without XM, connects to the back of the factory radio. PXH3GM1X harness retains XM,
connects to the XM tuner.
Make
Toyota
Model
4Runner
4Runner
4Runner
Avalon
Avalon
Avalon
Camry
Camry
Camry
Celica
Corolla
Corolla
Echo
FJ Cruiser
Highlander
Highlander
Highlander
Land Cruiser
Land Cruiser
Land Cruiser
Matrix
Matrix
Matrix
MR2
RAV4
RAV4
Sequoia
Sequoia
Sequoia
Sienna
Sienna
Sienna
Solara
Solara
Solara
Supra
T100
Tacoma
Tacoma
Tacoma
Tercel
Tundra
Tundra
Yaris
Prius
Highlander
Year
1998-2005
2005-2007
2006-2007
1998-2005
2005-2007
2006-2007
1998-2005
2005-2007
2006-2007
1998-2005
1998-2005
2006-2007
2000-2005
2007
2001-2004
2005-2007
2006-2007
1998-2005
2005-2007
2006-2007
2003-2004
2005-2007
2005-2007
2000-2005
1998-2005
2005-2007
2001-2005
2005-2007
2006-2007
1998-2005
2005-2007
2006-2007
1999-2005
2005-2007
2006-2007
1998
1998
1998-2005
2005-2007
2006-2007
1998
2000-2007
2007
2005-2007
All Years
2008
Part #
PXDP
PXDP2
PXDP
PXDP
PXDP2
PXDP
PXDP
PXDP2
PXDP
PXDP
PXDP
PXDP
PXDP
PXDP2
PXDP
PXDP2
PXDP
PXDP
PXDP2
PXDP
PXDP
PXDP2
PXDP
PXDP
PXDP
PXDP2
PXDP
PXDP2
PXDP
PXDP
PXDP2
PXDP
PXDP
PXDP2
PXDP
PXDP
PXDP
PXDP
PXDP2
PXDP
PXDP
PXDP
PXDP2
PXDP2
Not Compatible
Not Compatible
Harness
PXHTY3
PXH2TY1
PXHTY3 or PXH2TY1
PXHTY3
PXH2TY1
PXHTY3 or PXH2TY1
PXHTY3
PXH2TY1
PXHTY3 or PXH2TY1
PXHTY3
PXHTY3
PXHTY3 or PXH2TY1
PXHTY3
PXH2TY1
PXHTY3
PXH2TY1
PXHTY3 or PXH2TY1
PXHTY3
PXH2TY1
PXHTY3 or PXH2TY1
PXHGM3
PXH2TY1
PXHTY3 or PXH2TY1
PXHTY3
PXHTY3
PXH2TY1
PXHTY3
PXH2TY1
PXHTY3 or PXH2TY1
PXHTY3
PXH2TY1
PXHTY3 or PXH2TY1
PXHTY3
PXH2TY1
PXHTY3 or PXH2TY1
PXHTY3
PXHTY3
PXHTY3
PXH2TY1
PXHTY3 or PXH2TY1
PXHTY3
PXHTY3
PXH2TY1
PXH2TY1
Dip Switch Settings*
1,2,4,8 ON
2,4 ON
1,2,4,8 ON
1,2,4,8 ON
2,4 ON
1,2,4,8 ON
1,2,4,8 ON
2,4 ON
1,2,4,8 ON
1,2,4,8 ON
1,2,4,8 ON
1,2,4,8 ON
1,2,4,8 ON
2,4 ON
1,2,4,8 ON
2,4 ON
1,2,4,8 ON
1,2,4,8 ON
2,4 ON
1,2,4,8 ON
1,3,8 ON
2,4 ON
1,2,4,8 ON
1,2,4,8 ON
1,2,4,8 ON
2,4 ON
1,2,4,8 ON
2,4 ON
1,2,4,8 ON
1,2,4,8 ON
2,4 ON
1,2,4,8 ON
1,2,4,8 ON
2,4 ON
1,2,4,8 ON
1,2,4,8 ON
1,2,4,8 ON
1,2,4,8 ON
2,4 ON
1,2,4,8 ON
1,2,4,8 ON
1,2,4,8 ON
2,4 ON
2,4 ON
Vehicle Specific Notes
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
When using the PXHTY3 the green wires must be cut on the PXHTY3 harness
IMPORTANT TOYOTA APPLICATION INFORMATION
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function. When using the PXHTY3 with 2006-2007 vehicles the green wires must
be cut on the PXHTY3 harness. Fully compatible with factory installed Toyota Navigation Systems. Not compatible with Hybrid vehicles.
PXDP2: Radio must have a button labeled "SAT". Not compatible with factory satellite. If satellite is installed, it must be disconnected. Fully compatible with factory installed Toyota Navigation Systems. Not compatible with Hybrid vehicles.
*Dip Switch Settings: Please See Product Instructions for Dip Switch Configuration Settings
Make
Volkswagen
Model
All Models (Except Below)
All Models
All Models
Year
1998-2006
1998-2006
2003-2006
Part #
PXDP
PXDP
PXDP
Harness
PXHVW1
PXHVW2
PXHVW3
Dip Switch Settings*
1,8 ON
1,8 ON
1,8 ON
Vehicle Specific Notes
Trunk Mounting Location
For use with Single DIN radios
For use with Double DIN radios
IMPORTANT VOLKSWAGEN APPLICATION INFORMATION
PXDP: Not compatible with any factory external audio source such as: XM tuner, CD changer, or Cassette player. These devices must be disconnected during the installation and will no longer function. Not compatible with vehicles equipped with a factory Navigation
system. When possible, we recommend using the PXHVW2 or PXHVW3 harness and install the PXDP behind the radio. This will avoid the possibility of inherent noise problems with the factory VW CD changer cable that is found in some vehicles. Double DIN (4” Tall) VW
radios require the PXHVW3 to connect behind the radio.
PXHVW3: When using the PXHVW3 harness, connect the loose black lead to suitable chassis ground. If equipped with factory satellite, remove the blue OEM sub harness from the main OEM harness to plug in the PXHVW3 harness.
*Dip Switch Settings: Please See Product Instructions for Dip Switch Configuration Settings
Revision History
Date
1/2/2008
12/26/2007
12/26/2007
12/20/2007
12/18/2007
12/12/2007
12/12/2007
12/12/2007
12/12/2007
12/12/2007
11/12/2007
11/12/2007
11/12/2007
11/12/2007
11/12/2007
11/12/2007
11/12/2007
11/12/2007
11/12/2007
11/12/2007
11/12/2007
11/12/2007
11/12/2007
11/12/2007
11/12/2007
11/12/2007
11/12/2007
11/12/2007
11/12/2007
11/12/2007
11/12/2007
11/12/2007
11/12/2007
11/12/2007
11/12/2007
11/12/2007
9/21/2007
8/31/2007
8/24/2007
8/24/2007
8/24/2007
8/3/2007
Vehicle
Ford Expedition
Chevy Trailblazer
GMC Envoy
All GM Class II vehicles Prior to 03
Acura CL
Dodge Caliber
Jeep Compass
Jeep Patriot
Chrysler PT Cruiser
Dodge Ram
Ford Edge
Ford Escape
Ford Expedition
Ford Explorer
Ford Sport Trac
Ford F-150
Ford F-250
Ford F-350
Ford F-450
Ford Five Hundred
Ford Freestyle
Ford Focus
Ford Fusion
Ford Mustang
Ford Taurus
Ford Taurus X
Lincoln MKZ
Lincoln MKX
Lincoln Mark LT
Lincoln Navigator
Lincoln Zephyr
Mercury Milan
Mercury Marnier
Mercury Montego
Mercury Mountaineer
Mercury Sable
Pontiac Grand Prix
Ford Focus
Chrysler Pacifica
PT Cruiser
Ford/Lincoln/Mercury
Toyota Corolla
Year
2003-2004
2002-2003
2002-2003
Notes
PXDP Removed
PXDP Added
PXDP Added
PXDPGMT Apps Removed
2001-2002
2008
2008
2008
2008
2008
2007-2008
2008
2007-2008
2005-2008
2007-2008
2005-2008
2007-2008
2007-2008
2007-2008
2006-2007
2006-2007
2005-2007
2005-2008
2005-2008
2008
2008
2007-2008
2007-2008
2006-2008
2007-2008
2005-2006
2006-2008
2008
2005-2007
2006-2008
2008
2004-2007
2005-2007
2006
2007
2008
2005-2007
Removed
CHYP Added
CHYP Added
CHYP Added
CHYP Added
CHYP Added
PXAMG Added
PXAMG Added
PXAMG Added
PXAMG Added
PXAMG Added
PXAMG Added
PXAMG Added
PXAMG Added
PXAMG Added
PXAMG Added
PXAMG Added
PXAMG Added
PXAMG Added
PXAMG Added
PXAMG Added
PXAMG Added
PXAMG Added
PXAMG Added
PXAMG Added
PXAMG Added
PXAMG Added
PXAMG Added
PXAMG Added
PXAMG Added
PXAMG Added
PXAMG Added
PXDPGMT Removed
PXDP2 Removed
PXDP Added
CHYP Added
PXDP2 NOT Compatible
PXDP2 Removed
Installation Note:
When installing a PXHTY3 harness in any 2006 or newer Toyota vehicle, if
the audio becomes muted on all audio sources (CD, Tuner, etc.), it will be
necessary to cut the green wires on the harness. Cut and insulate all the
green wires that come out of pin 21 in the 22-pin connector that plugs
into the interface.
Green wires
22-pin connector