Royal Enfield Bullet 500CC Owner`s manual

Congratulations on becoming the proud owner of a legendary Royal Enfield motorcycle.
The new Bullet 500 is a motorcycle with the timeless handcrafted design of the legendary Bullet, now fitted with a
solid 500cc Unit Contruction Engine with twin-spark ignition for better combustion, superior power delivery and
improved fuel economy.
Do read this manual thoroughly before you begin riding to ensure that you operate your motorcycle the right
way, are aware of the terms and conditions of warranty, and know how to maintain it properly.
We urge you to avail o f the fo ur fr ee s er vices we o ffer, at the r ight tim e, at any of o ur Autho ri sed
Dealer / Service Point to keep your motorcycle in peak condition.
Please log on to w w w.r o y a l en f i e l d .c o m to kno w m or e abo ut the his to ry o f the wo rl d’s oldest
motorcycle brand, our other products, and for exciting news of riding tours and events organised for Royal Enfield
motorcycle owners.
Welcome to motorcycling the Royal Enfield way. Ride safe and enjoy the trip!
IMPORTANT NOTICE
Keep this manual in a convenient place for easy
reference.
Beca us e o f co n tino us i m pro vem e nts i n t he
pro duct and changes that may occur in the
manufacturing process, subsequent to printing of
this m anual , i t i s po ssible so me instr uctio ns,
illustrations, pictures or designs found within this
m anual m ay dif fer fro m tho se fo und on the
vehicle.
If any information is not understood in the manual
contact your Authorised Dealer / Service Point for
assistance.
If the motorcycle is being used by any friend,
relatives, or others it is responsibility of the owner
to make certain that the owner’s manual is read
and fully understood prior to usage and has been
instructed on it’s safe and proper use.
However the technical information found within
thi s m a nual was co r r ect at the ti me i t was
approved for publication.
The motorcycle is designed for normal on road
use only. Operation in off-road usage in some
areas may be illegal and could be dangerous.
Ro yal Enfi eld r es er ves the r ig ht t o m a ke
production changes at any time without prior
notice and without incurring any obligation to
m ak e s am e o r s i m ilar chan ges to vehi cles
previously built or sold.
Obey local law and regulations.
In the event of motorcycle being resold, it is the
responsibility of the owner of the motorcycle to
hand over the manual along with the motorcycle
and it’s documents.
“© Copyright 2014 Eicher Limited, Royal Enfield Unit. All Rights Reserved. No part of this manual shall be copied,
distributed or otherwise dealt without the express permission in writing of Eicher Motor Limited, Royal Enfield Unit.”
Part No. 584639/A / Qty.1000 / Apr. ‘14
2
IMPORTANT NOTICE
SAFETY DEFINITIONS
However i f you have any queries, cl ar ifi cation,
Statements in this manual preceded by the following
words are of special significance :
suggestions/feedback, please write to us or e-mail at
“customerservice@royalenfield.com”.
WARNING
War ni ng i ndicates a potenti all y hazardo us
situation, which if not avoided, could result in serious
injury.
CAUTION
Caution indicated a protentially hazardous situation,
which if not avoided, may result in property damage,
in minor or moderate injury.
NOTE
SERVICE HEAD QUARTERS
Indicates important and useful messages for clearer
understanding.
Thiruvottiyur High Road, Thiruvottiyur,
Royal Enfield, A Unit of Eicher Motors Limited,
Chennai - 600 019.
Phone : 044 - 4223 0400, Fax : 044 - 4201 1719
All Images shown are for reference to explain and
need not to be exactly the same on the model
you own.
E-mail : customerservice@royalenfield.com
Website : www.royalenfield.com
3
CONTENTS
PERSONAL & VEHICLE INFORMATION ......................... 7
OPERATION OF CONTROLS .............................................. 26
FREE SERVICE RECORD ..................................................... 8
- Ignition Switch ......................................................... 26
SAFE OPERATING RULES .................................................. 9
- Steering lock ............................................................. 26
RULES OF THE ROAD ......................................................... 15
- Fuel tank cap ............................................................ 27
TECHNICAL SPECIFICATIONS ......................................... 17
- Side Box ...................................................................... 27
- Engine ........................................................................ 17
- Head lamp switch .................................................. 28
- Ignition System ........................................................ 18
- Dip Switch .................................................................. 28
- Transmission ............................................................ 18
- Head lamp Day flash ........................................... 28
- Electricals ................................................................. 19
- Engine Kill Switch .................................................... 29
- Chassis ....................................................................... 20
- Ho rn ............................................................................. 29
- Dimensions ............................................................... 21
- Turn Signal Switch .................................................. 29
- Weights ...................................................................... 21
- Engine Start Switch ................................................. 30
VEHICLE IDENTIFICATION NUMBER ............................. 22
- Battery Box ................................................................ 30
KEY PARTS LOCATION ....................................................... 23
- Fuel Tap ...................................................................... 30
- Top View .................................................................... 23
PRE OPERATIONAL CHECKS ............................................ 31
- Right Side View ........................................................ 24
RUNNING IN PERIOD ........................................................ 32
- Left Side View ........................................................... 25
STA RT ING ............................................................................. 33
4
CONTENTS
GEAR SHIFTING .................................................................. 35
- Rear wheel removal ............................................. 49
PA RKING ............................................................................... 36
- Rear wheel assembly ........................................... 50
- Center Stand ............................................................ 36
- Adjustment - Clutch ................................................ 51
- Side Stand ................................................................. 36
-
Drive Chain tension ......................................... 51
TOOLS AND FIRST AID KIT ............................................. 37
-
Checking Rear Brake Pedal height ........... 52
RECOMMENDED LUBRICANTS ....................................... 38
-
Rear Brake Pedal height Adjustment ....... 53
PERIODICAL MAINTENANCE ......................................... 39
-
Chain Lock Fitment .......................................... 53
MINOR MAINTENANCE TIPS ......................................... 43
-
Adjustment of Gas Filled Shockabsorber .... 54
- Control Cables, Handle bar lever,
Pivots, Center / Side Stand Pivots ....................... 43
- Removal of Battery on Vehicle ........................... 55
- Engine Oil Level Inspection ................................. 43
- Assembly of Battery on Vehicle ......................... 56
- Engine Oil Change ................................................. 44
- Changing Electrical Components .................... 57
- Battery Maintenance ............................................ 55
- Spark Plug ................................................................. 45
-
Head Lamp bulb replacement .................. 57
- Brake fluid ................................................................. 46
-
Tail Lamp bulb replacement ...................... 59
- Inspection of tyres and wheels ........................... 46
-
Trafficator bulb replacement .................... 59
- Tyre pressure ............................................................ 47
-
Fuse ....................................................................... 60
- Front Wheel removal .............................................. 47
-
Blade Fuse usage List ..................................... 60
- Air Filter element cleaning / replacement ... 61
- Front Wheel assembly ............................................ 48
5
CONTENTS
WASHING PROCEDURE .................................................... 62
- Excessive fuel consumption ................................ 72
- Precautions .............................................................. 62
- Ignition knock .......................................................... 73
- After Washing .......................................................... 62
- Brakes poor .............................................................. 73
STORAGE PRECAUT ION .................................................. 63
- Vehicle wobbles ...................................................... 74
- Preparing the motorcycle for reuse .............. 64
- Electricals .................................................................. 74
LONG TRIP PRECAUTIONS ............................................. 65
- Electric Start .............................................................. 76
- Checks prior to the commencement .............. 65
WARRANTY TERMS & CONDITIONS ............................ 77
- Checks after every 1500 kms ............................. 65
EMI SSION WARRA NTY ...................................................... 79
- Items to be carried ............................................... 65
A LL INDIA ROA D SIGNS ....................................83
CARING FOR MILEAGE ................................................... 66
FREE SERVICE COUPONS .................................................. 84
COMPLETE WIRING DIAGRAM - BULLET 500 ........... 68
PAID SERVICE / MAINTENANCE RECORD ................... 93
TROUBLE SHOOTI NG ....................................................... 69
LOG BOOK ............................................................... 101
- Engine fails to start ............................................... 69
NOT ES ...............................................................106
- Engine misfiring ..................................................... 70
A NN EXUR ES
- Engine starts, but runs irregularly & stops ......... 71
- Vehicle Installation Form
- Poor pickup .............................................................. 71
- Pre-Delivery Inspection Report (PDI)
- White / blue smoke ................................................ 72
- Bike Installation Confirmation By Customer
- Engine over heating ............................................. 72
- Form 22
6
PERSONAL & VEHICLE INFORMATION
Name
Door No./Street
Locality
City
Contact Nos.
State
Res:
Off:
Pin
Mobile:
Email:
Engine No.
Battery No.
Frame No.
Battery make
Reg. No.
Licence No.
Date of Sale
Valid till dt.
Model
Key No. :
Tyre make
Colour
Sold by
Dealer Code
Vehicle Installation Form (VIF) No.
7
FREE SERVICE RECORD
It is our endeavour to provide excellent service to your Bullet 500 at all times. Towards this we provide 4 free
services at specific Intervals.
Please avail these services at the specified time, in any of the Royal Enfield Authorised Dealer / Service Point
nearest to you and as a token of satisfactory services, kindly return the free service coupon duly filled in and
signed, to the service outlet.
Availing the free services in the specified time is a prerequisite for warranty consideration. The cost of fuel, oil,
grease etc. used for all free services are chargeable to the customer.
1 st Service
2 nd Service
3 rd Service
4 th Service
Dealer / ASP
Rubber Stamp
Dealer / ASP
Rubber Stamp
Dealer / ASP
Rubber Stamp
Dealer / ASP
Rubber Stamp
Date of Service
Kms Covered
Servicing
Dealer’s / ASP
Name, Address
NOTE
Please ensure that the free service details are recorded in this sheet immediately after the service is carried out.
8
SAFE OPERATING RULES
Before operating your new motorcycle, it is your
Use only genuine Royal Enfield spare parts and
responsibility to carefully read and follow the
approved accessories. Use of other manufacturer’s
operating and maintenance instructions detailed
performance parts may affect the performance of
in thi s m a nual f or you r o w n s a fety, yo ur
your motorcycle and render the motorcycle void of
motorcycle and that of others.
warranty. See your Royal Enfield dealer for details.
Know and respect the rules of the road. Be a safe
Whenever refuelling your mo torcycle, please
rider for your own safety and for other road users.
exercise utmost caution and carefully observe the
Before starting the motorcycle, check for proper
following rules :
operation of brakes, clutch, gear shifter, handle
DO NOT smoke and please ensure that there
bar controls, tyre pressures, fuel and oil levels.
are no open fla m es or s park s ne ar t he
motorcycle, when refuelling OR servicing the
WARNING
fuel system.
Royal Enfield cautions you against the use of
certain nonstandard parts such as aftermarket and
Switch OFF mobile phones and other hand
custom made extended front forks or suspensions,
held electronic devices / gadgets.
whi ch m ay a dver sely aff ect per f o rm a nce and
Open the fuel filler cap slowly.
handling. Removing or altering original parts may
adversely affect performance and could result in an
Refuel in a well ventilated area with the engine
accident causing serious injury.
turned off.
9
SAFE OPERATING RULES
DO NOT fill the tank to its brim. Please fill fuel
A new motorcycle must be operated according to
the special break-in-procedure. See BREAK-IN-THE
FIRST 500KM section.
only till the bottom of the filler neck insert, so
as to leave air space in the fuel tank to allow
for fuel expansion (for Spec. Ref. Page No. 20).
Operate motorcycle only at moderate speeds and
out of traffic until you have become thoroughly
fa m il i ar w i th i ts o per ati o n an d ha ndl i ng
characteristics under all conditions.
WARNING
Pe tr ol is extre m el y fl am m able an d h i gh ly
DO NOT exceed the legal speed limit or drive too
fast for existing conditions. Always reduce speed
when poor driving conditions exist. High speed
increases the influence of any other condition
affecting stability and increases the possibility of
loss of control.
explosive. Use care when handling Petrol. Always stop
the engine when refuelling or servicing the fuel
system. Do not smoke or allow open flames or sparks
near Petrol. Do not store motorcycle with
Petrol in
the tank, within the home or garage where open
flames, pilot lights, sparks or electric motors are
present. Inadequate safety precautions could cause
NOTE
an explosion or fire which could result in damage to
If you are an inexperienced rider we recommend that
you obtain formal training on correct motorcycle
riding techniques and become thoroughly familiar
with the operation of your particular motorcycle. New
ri ders s ho uld gai n ex p er i ence und er v ar io us
conditions while driving at moderate speeds.
property, serious injury.
10
SAFE OPERATING RULES
WARNING
Ope rat e
yo ur
m otor cycl e
de fens ivel y.
Remember, a motorcycle does no t af ford the
same protection as an automobile in an accident.
One o f the mo st com mon accident situati ons
occurs when the driver of the other vehicle fails
to see or recognize a motorcycle and turns into
the oncoming motorcyclist.
Avoid overspeeding and never travel over the
speed limit. Excessive speed may cause loss of control
and could r esult in an accident caus ing serious
injury.
DO NOT exceed >110 km/h solo riding.
DO NOT exceed >90 Km/h when carrying a pillion
or cargo.
Wear an appro ved helmet, clothing, and foot
gear suited for riding a motorcycle. Bright OR
light colors are best for greater visibility in traffic,
specially at night. Avoid loose, flowing garments
and scarves.
Pay strict attention to road surfaces and wind
conditions . Any two wheeler vehicle may be
subject to the following upsetting forces :
Wind blasts from passing trucks.
Whe n ca r r yi ng a pil lio n r id er, it i s yo ur
responsibility to instruct them on proper riding
procedures.
Rough uneven road surfaces.
Slippery road surfaces.
These forces may affect the handling characteristics
of your motorcycle. If this happens, reduce speed and
gui de the m o to rcycle wi th a r el ax ed gri p to a
controlled condition. Do not brake abruptly or force
the handlebar.
DO NO T allo w o ther in dividual s , under any
circumstances, to operate your motorcycle unless
you know they are experienced, licensed riders
and are thoroughly familiar with the operating
conditions of your motorcycle.
11
SAFE OPERATING RULES
WARNING
In emergency situations, if a temporary repair is
M ai n tai n th e reco m m ended t yre pr ess u r e.
made ride slowly with as light a load as possible until
Ens ur e the f ro nt and r ear wheel s ar e co rr ectly
the tyre is permanently repaired or replaced.
aligned and the tyres are seated evenly & properly
in the rims. Check for correct tightness of the spokes
Failure to heed this warning could result in serious
in the r im s. Inspect your tyres peri odically and
injury.
replace tyres with approved tyres only. Failure to do
so can lead to improper balance, abnormal tread
Safe motorcycle operation requires alert mental
wear, poor handling and could resul t in serious
judgement combined with a defensive driving
injury.
attitude. DO NOT allow fatigue, alcohol or drugs
to endanger your safety or that of others.
WARNING
Maintain your motorcycle in proper operating
Royal Enfield recommends replacement of any
condition as per Periodical Maintenance Chart
tube / tyre punctured or damaged. In some cases
(R ef Page No .4 0 ). Par t icu l ar l y i m po rt ant to
small punctures in the tread area may be repaired
from within the demounted tyre by your Royal Enfield
m ot or cy cl e stab ili t y is pro per tyre i nf lati o n
dealer. Speed should not exceed 60 km/h for the first
pressure, tread condition. Pay strict attention to
24 hours after repair and the repaired tyre should
loose and / or broken spokes, free movement of
steering system.
Never be used over 90 km/h (applicable tube less tyre)
12
SAFE OPERATING RULES
WARNING
WARNING
Avoid any contact with the exhaust system. Wear
clothing that will completely cover the legs while
riding. The exhaust system gets very hot when the
engine is running and remains too hot, even after
the engine is turned off (due to catalic converter).
Failure to wear proper or protective clothing could
result in serious injury.
DO NOT operate motorcycle with a loose, worn
or damaged steering system, including the front and
rear sus pensio n system. Contact your dealer for
repair of steering or suspension system. Damaged
steering or suspension components may adversely
affect handling which could result in serious injury.
WARNING
WARNING
Regularly inspect rear shock absorbers and front
forks and look for leaks. Replace worn parts. Worn
parts can adversely affect stability and handling.
Ex haus t ga s es cont ain s po i so n o us car b on
mono xide (CO.) and chemi cals , known to cause
serious health hazards.
WARNING
WARNING
For your personal welfare, all the listed service
and m aintenance recom m endatio ns sho ul d be
per fo rm ed. Lack of regular maintenance at the
suggested intervals may affect the safe operation of
your motorcycle, which could result in serious injury.
Motor cycle batteri es contain lead and lead
components, acids and chemicals known to cause
serious health hazards. Exercise extreme caution
while handling a battery. Wash hands thoroughly
whenever a battery is handled.
13
SAFE OPERATING RULES
WARNING
on the frame Down tube. (GVWR is the sum of the
wei ght of the m otor cycle, acces so ries, and the
maximum weight of the rider, passenger and cargo
that may be safely carried.) Exceeding GVWR may
lead to instability of the motorcycle, which could
cause an accident and result in serious injury.
Consult your Royal Enfield Dealer regarding any
questions or problems that occur in the operation of
your motorcycle. Failure to do so may aggravate an
initial problem, cause costly repairs, jeopardize your
personal safety and could result in serious injury.
WARNING
WARNING
DO NOT tow a disabled motorcycle. The steering
and handling of the disabled motorcycle will be
impaired due to the force of the towline. If a disabled
motorcycle must be transported, use a truck or a
trailer. Towing a motorcycle may cause loss of control
of the motorcycle in the front, leading to an accident
resulting in serious injury .
Use only genuine Royal Enfield replacement
fasteners tightened to the proper torque. We caution
you against the use of certain non standard parts
such as aftermarket and cus tom made fasteners
which may not have specific strength, finish and type
requirements to perform properly in the assembly
and its environment. The use of any nonstandard
parts, including fasteners, could result in serious
injury.
WARNING
DO NOT pull a trailer behi nd a mo to rcycle.
To w ing a tr ai le r ma y ca use redu ced brak i ng
efficiency, tyre overloading and unstable handling.
Towing a trailer may cause loss of control of the
m otorcycl e in the front, leading to an acci dent
resulting in serious injury.
WARNING
DO NOT exceed the Gross Vehicle Weight Rating
of your motorcycle. The Gross Vehicle Weight Rating
(GVWR) is shown on the information plate, located
14
RULES OF THE ROAD
Be sure front & rear number plates is installed in
the position specified by law and is clearly visible
at all times.
may cause loss of control of vehicle, which could
result in death or serious injury.
Ride at a safe speed that is consistent with the type
of road surface you are on. Pay strict attention to
whether the surface is :
Keep to the correct side of the road centre line
when meeting oncoming vehicle.
Dry
Icy
Always sound your horn, actuate your turn signals,
and exe rcis e CA UTI ON w hen pass ing oth er
vehicles going in the same direction. Never try to
pass another vehicle going in the same direction
at street intersections, on curves, or when going
up/or down a hill.
Oily
Wet
Watch for loose debris, such as leaves, slippery
substances or loose gravel that can hamper the
stability of your vehicle.
At street intersection give the right-of-way to the
vehicle on your left or right. DO NOT presume you
have the right-of-way.
DO NOT exceed the legal speed limit or drive too
fast for existing conditions. Always reduce speed
when poor driving conditions exist. High speed
increases the influence of any other condition
affecting stability and increases the possibility of
loss of control.
Always signal when preparing to stop, turn or
pass.
Whi le tur ning either r igh t o r l eft, watch fo r
pedestrians, animals as well as vehicles.
All traffic signs, including manual controls at
intersections, should be obeyed promptly. SLOW
DOWN at traffic signs near schools and CAUTION
signs at railroad crossings.
WARNING
Avoid excessive speed and never travel at a
speed faster than the speed limit. Excessive speed
15
RULES OF THE ROAD
When intending to turn, signal at least 100 feet
(30.5 meters) before reaching the turning. Be close
to the center line (unles s l ocal r ul es requir e
otherwise), slow down and then turn carefully.
Never jump a traffic light. When a
change is imminent from GO to STOP
(or vice versa) at intersections, slow
down and wait for the light to change
to green. Never run through a yellow
or red traffic light.
SIDE VIEW MIRRORS
Red
Yellow
Your motorcycle is equipped with convex mirrors and
have a curved surface. This type of mirror is designed
to give a much wider view to the rear than a flat
mirror; however, cars and other objects seen in this
type of mirror will look smaller and farther away than
when seen in a flat mirror.
Green
DO NOT leave the curb or parking area without
signaling. Be sure your way is clear to enter
moving traffic. A moving line of traffic always has
the right-of-way.
Use care when judging the size or distance of objects
seen in these mirrors.
Park your motorcycle on a firm and flat surface to
prevent it from falling over.
NOTE
To help you establish the relative distance of vehicles
behind your motorcycle, adjust each mirror in such
a way, that a small portion of your shoulder is visible
and a large portion behind your motorcycle is seen
clearly.
Pr o tec t yo ur m o to r cycl e ag ains t th eft. A ft er
parking your motorcycle, remove Ignition key
from switch and lock the steering head.
16
TECHNICAL SPECIFICATIONS
ENGINE
Engine ............................................................
Single Cylinder, 4 Stroke, Twinspark, Aircooled
Capacity ........................................................
499 cc (Displacement)
Bore ................................................................
84 mm
Stroke .............................................................
90 mm
Compression ratio ......................................
8.5 : 1
Max. Power @ RPM .....................................
26.1 BHP @ 5100 rpm
Max. Torque @ RPM ...................................
40.9 Nm @ 3800 rpm
Air Filter Element .........................................
Corrugated Paper Element
Fuel Supply ...................................................
Carburetor with Throttle Position Sensor (TPS)
Engine Start ..................................................
Electric / Kick
Engine Oil Capacity ...................................
2.75 Litres.
Lubrication ...................................................
Wet Sump, Forced Lubrication
Engine Oil Grade ........................................
Royal Enfield 15W50 API SL Grade Engine Oil (JASO MA)
Cooling system ............................................
Natural Air Flow
Carburetor ...................................................
UCD 33
17
TECHNICAL SPECIFICATIONS
IGNITION SYSTEM
Ignition system ...........................................
TCI Unit, Multi Curve (Variable Ignition Timing)
Spark plug ...................................................
WQR8DC (Bosch Super) M14 & UR6DC (Bosch Super) M10
Spark plug Electrode gap ......................
.................................................................
WQR8DC 0.80 to 0.90 mm
UR6DC
0.70 to 0.80 mm
TRANSMISSION
Clutch ............................................................
Wet Multiplate (7 Plates Clutch)
Primary drive ..............................................
Duplex Chain
Primary Drive Ratio ...................................
2.15 : 1
Gear box .......................................................
5 Speed Constant Mesh
Gear shift pattern ......................................
1-N-2-3-4-5
Gear Ratios ..................................................
1st-3.06:1
Secondary Drive (F.D. Sprocket) ............
18 Teeth
Final Ratio ....................................................
2. 11 : 1
Drive Chain links .......................................
102 links
2nd-2.01:1
18
3rd-1.52:1
4th-1.21:1
5th-1:1
TECHNICAL SPECIFICATIONS
ELECTRICALS
Generation ...................................................
Alternator
System ............................................................
12V DC
Battery ...........................................................
12V - 14 AH
Head lamp ...................................................
12V, 60/55 W, Halogen
Position lamp ..............................................
12V, 4W
Brake / Tail lamp .......................................
12V, 21/5 W
Turn signal ...................................................
12V, 10W - 4 nos.
Pilot lamp .....................................................
12V, 2 W - 2 nos.
Speedometer lamp ...................................
12V, 3.4 W - 1 no.
Turn signal / High beam indicator ......
12V, 1.7 W - 2 nos.
Neutral Indicator .......................................
12V, 1.7 W - 1 no.
Horn (Dual) ..................................................
12V, 2.5 Amp (Max.) X2
Starter Motor ...............................................
12V, 0.9 KW
19
WARNING
Using bulbs / other electrical
gadgets other than specified rating
may lead to over loading / erratic
behaviour / prematur e fai lur e of
electrical system.
Modifications on the bike which are
not approved by Royal Enfield may
not only disqualify for warranty, but
also affects performance of the bike.
TECHNICAL SPECIFICATIONS
CHASSIS
Frame .............................................................
Tubular Frame
Tyre size .........................................................
Front: 90 / 90 - 19” - 52 P
Tyre pressure ...............................................
Front- Solo: 1.41 Kg/cm2 (20 PSI) Pillion: 1.55 Kg/cm2 (22 PSI)
.................................................................
Rear: 120 / 80 - 18” - 62 P
Rear- Solo: 2.11 Kg/cm2 (30 PSI) Pillion: 2.25 Kg/cm2 (32 PSI)
Fuel tank capacity ....................................
13.5 Litres ***
Reserve capacity .......................................
2 Litres (approx.)
Dead stock of petrol (unusable fuel) ..
0.75 Litres (approx.)
Suspension ...................................................
Front: Telescopic, 130mm Travel
.................................................................
***Fue l t an k i s n ot a m eas ur i n g
instrument. The capacity of tank may
vary slightly from specified value.
Rear: Twin gas charged shock absorbers, 80mm travel
Front fork oil capacity ..............................
195 ml per leg
Front fork oil ................................................
1F Endurance (or Royal Enfield) fork oil
Brakes ............................................................
Front : Hydraulic 280 mm Ventilated Disc
.................................................................
Rear : Foot Operated 153mm Single Lead Internal expanding
Brake oil capacity .....................................
60 ml
Brake oil grade ..........................................
DOT 3 or DOT 4
20
TECHNICAL SPECIFICATIONS
DIMENSIONS
Length ...........................................................
2140 mm
Width ..............................................................
810 mm (Without Mirror)
Height ............................................................
1110 mm (Without Mirror)
Wheel base ..................................................
1370 mm
Saddle height .............................................
800 mm
Ground clearance .....................................
135 mm
N O TE :
BS III
This vehicle meets Emission Norms Bharat (Trem) Stage - III
WEIGHTS
Kerb Weight (with 90% Fuel) ...................
193 Kg
Max pay load .............................................
172 Kg
NOTE
1.
Values / Dimensions given above are for your guidelines only.
2.
In view of continuous improvements being done on our products, the specifications are subject to change
without notice.
21
VEHICLE IDENTIFICATION NUMBER - DETAILS
FRAME NUMBER
ENGINE NUMBER
Punched on steering head tube RH side.
Punched on top of the engine LH side.
22
KEY PARTS LOCATION
12
TOP VIEW
12
1. Turn signal switch
6
3 4
2. Horn button
7
3. Clutch lever
4. Day flash switch
5. Head lamp dip switch
8
6. Ignition switch
7. Speedometer
8. Front brake lever
1
10
5
2
11
9
9. Accelerator
10. E-Start Switch
11. Fuel tank cap
12. Rear View Mirror
23
KEY PARTS LOCATION
RIGHT SIDE VIEW
1.
RH Trafficator Front
2
5
2. Starter Motor
1
3. Brake Pedal
6
4. Kick Starter Lever
4
5.
Air Filter Box
6.
RH Trafficator Rear
3
24
KEY PARTS LOCATION
LEFT SIDE VIEW
1. Trafficator Front LH
2
3
4
5
2. Spark Plug
3. Battery Cover
1
4. Electricals Box LH
6
10
9
8
7
5. Rear Shock Absorber
6.
Trafficator Rear LH
7.
Side Stand
8.
Centre Stand
9.
Gear Change Lever
10.
25
Horn
OPERATION OF CONTROLS
IGNITION SWITCH
STEERING LOCK
OFF
Turn key clockwise to lock.
Lock the steering when leaving
bike parked.
Turn key anti clockwise to unlock.
CAUTION
ON
Protect your motorcycle against theft.
After parking your motorcycle, remove
the ignition key from switch and lock
the steering head.
Turn handle bar to extreme left, before attempting to lock
steering.
Do NOT lubricate barrel locks with petroleum based lubricants
or graphite. Inoperative locks may result in damage to your
vehicle.
26
OPERATION OF CONTROLS
FUEL TANK CAP
SIDE BOX
Turn key
AIR FILTER BOX RH
clockwise
Turn Key anti-clockwise to open
to open
SIDE BOX LH
Press cap to lock with key in position
Turn Key anti-clockwise to open,
it contains Tools Kit & Fuse
NOTE
NOTE
Key can be r em o ved only i n lo ck ed
position.
Key is common for ignition, petrol tank cap, steering lock,
side boxes and battery cover.
Key for fuel tank and tool boxes can be removed from the
lock only in locked position.
27
OPERATION OF CONTROLS
HEAD LAMP SWITCH
DIP SWITCH
OFF
Low beam
Pilot Light ON
High Beam
Head Light ON
HEAD LAMP DAY FLASH
Press for
Headlight Flash
28
OPERATION OF CONTROLS
ENGINE KILL SWITCH
TURN SIGNAL SWITCH
Run
Left
Stop
OFF (Push to off)
HORN
Right
Press
29
OPERATION OF CONTROLS
ENGINE START SWITCH
FUEL TAP
Press
OFF
Turn knob to
horizontal position
Main ON
Turn knob
downward position
BATTERY BOX
Turn anti clockwise
to open
Reserve ON
Turn knob upward
position
30
PRE OPERATIONAL CHECKS
A careful check of the following must be carried out
every time before riding and specially after long
per io ds o f sto r age to d eter m ine if addi ti on al
maintenance is necessary.
5. Engine oil level.
MAX
MIN
1. Tyres for correct pressure, abrasions or cuts.
2. Rear chain for proper tension.
6. Wh eel
Drive Chain
s po ke
for
proper tightness, no
breakage.
Spokes
Clutch
7. Headlamp, tail lamp, brake lamp and indicator
3. B r a k e s ,
a nd
s teeri ng
th ro tt l e
lamps for proper operation.
fo r
WARNING
responsiveness.
For your personal welfare and safety, all the
poi nts m ent io ne d ab o ve s ho u ld b e pe rf or m ed
per io di call y. Failu re to do s o, m ay af fe ct s afe
operation and damage your motorcycle and could
result in an accident causing serious injury.
4. Cable for fraying or
cri m ping and f r ee
operation.
31
RUNNING IN PERIOD
Avoid driving the motorcycle with full throttle
o peni ng. Var y the s pe ed o f th e m otor cycl e
regularly but avoid using the motorcycle above
3/4 throttle opening position.
Proper running-in is very important for obtaining
maximum life and performance of a new motorcycle.
The following guidelines explain proper running-in
procedures.
Since the engine is brand new, it should not be loaded
excessively for the first 2,000 kms. During the first few
hundred kms, the various parts in the engine wear and
polish themselves to the correct operating clearances.
Driving with prolonged full throttle operation, or any
high speed conditions might result in excessive heating
of the engine and cause abnormal wear of the moving
parts and hence must be avoided.
1.
3.
Avo id prolonged full-throttle operation. Var y
speed occasionally.
CAUTION
After covering the first 500 kms. please replace the
engine oil and oil filter element.
0 - 500 Kms :
Roy al Enfi eld engi nes ar e air- co ol ed a nd
consequently require forced air cooling over the
cylinders and heads to maintain proper operating
temperature. Extended periods of idling may over
heat the engine, resulting in serious engine damage.
The recommended speeds for the first 500 Kms is
bel ow 5 0 K mph. Dur i ng thi s pe ri od avo id
o p erat i ng the m o to rcyc le with f ul l th r ott le
opening. Stop the motorcycle for about 5 to 10
minutes to let it cool down, after every hour of
run ni ng. Var y the s peed o f t he m o to rcy cle
regularly during running but avoid using the
motorcycle above ½ throttle opening position.
2.
2,001 kms and above
DO NOT run the engine at extremely high RPM with
clutch disengaged or transmission in neutral as it can
cause serious engine damage.
An engine running long distances at high speed must
be given close attention to avoid over heating and
possible engine damage.
501 - 2000 Kms.
The recommended speed is below 80 Kmph.
32
STARTING
Ens ur e Engi ne s to p
swi tch is i n “R UN”
position
STARTING PROCESS (KS / ES)
Turn fuel tap to
‘ON’
Ensur e the side and
m ai n st ands ar e in
released position
Ensure that gears are
in neutral and neutral
lam p is glo wi ng i n
cluster box.
Use cho ke i n co ld
condition
CAUTION
N
Do not force the gear lever while attempting to shift
to neutral. Move the motorcycle back & forth and
simultaneously press gear lever to come to neutral.
Ensure neutral indicator light comes “ON”’ in the
Speedometer.
Switch on ignition.
WARNING
Before starting engine, always shift gears into
neutral.
33
STARTING
Pres s Star ter Butto n
and release as soon
as engine starts.
USING KICK START
Sl i ghtl y cr ank the
en gine fur the r ti ll
com pres s ion eas es
over.
Release the choke, if
applied
Start the motorcycle
wi th a
po werf ul
swinging kick.
NOTE
Release the choke, if
applied
A clutch switch is provided in the system for the
safety of the rider. This is to prevent the vehicle from
starting when the vehicle is in gear. To start the
engine when it is in gear, pull clutch lever, press
starter button and release as soon as the engine starts.
USING ELECTRIC START
Press starter button and release starter switch
once the engine starts.
Press Clutch Lever.
If the engine does not start on the first attempt in
cold climate, release the starter button, wait for
30 s econds before pressing the starter button
again.
34
GEAR SHIFTING
Pre ss th e gear
pedal with heel to
eng age 2 nd and
higher gear.
Warm up engine
for 2 minutes - till
idling is consistent/
stable
GEA R
1
N
SH IF T PATT ERN
2
3
4
5
Follow the same
procedure for 3rd, 4th
and 5th gear.
Press clutch lever towards the hand grip.
Press gear pedal with toe to engage 1st gear.
Gentl y ope n th ro tt le and rele ase clut ch
simultaneously. If clutch is released suddenly, the
engine may stall and cause a jerky start.
NOTE
CAUTION
Always move the motorcycle in first gear position only.
T he clutch m us t be ful ly dis enga ged befo re
attempting a gear shift. Failure to fully disengage the
clutch may cause a jerky start and / OR stalling the
engine besi des caus ing damage to tr ansm issi on
parts.
When engine speed decreases, while climbing a
gradient or running at a reduced speed, shift to the
appropriate lower gear to prevent the engine from
stalling or straining to pull.
35
PARKING
PARKING VEHICLE ON CENTER STAND
PARKING VEHICLE ON SIDE STAND
Select a firm, flat surface
Select a firm, flat surface
Hold handle bar straight
Lower Side Stand and gently tilt motorcycle to the
left till it rests firmly.
Lower center stand, and ensure that both the legs
of the stand are resting evenly on firm ground.
Apply pressure on the fulcrum lever on the center
stand and pull vehicle backwards, gently as
shown in pic.
WARNING
Always park the motor cycle on a firm and flat
surface. Parking in a soft ground may cause stand to
sink and the motorcycle to fall, causing injury to you
or to others and damage to the motorcycle parts.
36
TOOLS & FIRST AID KIT
1
2
3
4
5
5
6
7
6
1
4
S.No.
Description
Qty.
1.
Tool bag
1
2.
Screw driver O6 X 160
1
3.
Tommy bar
1
4.
Tubular spanner
1
5.
Tool Spark plug
1
6.
Double end spanner 10 X 12
2
3
2
S.No. Description
1.
2.
3.
4.
5.
6.
7.
Antiseptic cream 5 gms
Gauze bandage 5 cm x 2 cm
Elastic Gauze bandage 8 cm x 1 mtr.
Wash proof plaster 1.9 cm x 7.2 cm
Sterilized Gauze Swab 5 cm x 5 cm
Sterilized elastic plaster 7 cm x 6 cm
First aid kit pouch
Qty.
1
1
1
2
2
1
1
NOTE
This Tool Kit is kept in Tool box. Refer Page No. 27.
37
RECOMMENDED LUBRICANTS
Engine Oil
Grade
Royal Enfield 15 W 50 API SL Grade
Engine Oil
(JASO MA)
Grade
Front Fork Oil
Royal Enfield
Front Fork Oil
(or 1F Grade
Endurance)
Capacity 195 ml/leg
Brake Fluid
Grade
DOT 3 or DOT 4
Capacity 60ml
ISO 14001 – EMS
Operation Control Process
Capacity 2.75 Ltrs. (with oil filter)
2.50 Ltrs. (during oil & filter element
replacement)
WARNING
1. All customers are advised timely replacement of
Engine Oil, Fork Oil & Brake Oil at the dealership
/ASP. In case done privately, it is advise to reach
old/used Oil to our authorised vendor through RE
Dealer/ASP
2. Similarly we advise for disposal of old/used
Battery, Tube & Tyres as mentioned in above point
No.1.
DO NOT s wi tch o il brands indi scriminately because some oil inter act chemically when m ix ed.
Use of inferior oils or non-detergent oils can damage the engine.
DO NOT Mix DOT 3 & DOT 4 brake fluid together.
38
PERIODICAL MAINTENANCE
The maintenance schedule detailed here will help you to maintain your Bullet 500cc meticulously and to get
a long trouble free service. The schedule provided herein is based upon average riding conditions and
indicates the mileage at which regular inspections, adjustments, replacements and lubrications must be
carried out.
The frequency of the maintenance must be shortened depending upon the severity of the driving condition
OR if the motorcycle is used in a very dusty environment, severe climatic cold and hot conditions, bad roads,
stagnant water etc., Contact a nearest Royal Enfield Authorised Dealer / Service Point for expert advice and to
carry out the periodical maintenance.
WARNING
For your personal welfare, all the listed service and maintenance recommendations should be performed.
Lack of regular maintenance at the suggested intervals may affect the safe operation of your motorcycle
causing the motorcycle to malfunction and stall abruptly resulting in an accident and cause serious injury.
39
PERIODICAL MAINTENANCE
S.
No.
FREE SERVICE
whichever is earlier
Kms (x 1000) 0.5
3
6
9
12
DESCRIPTION
Months
1.5
3
6
9
R
I
R
I
R
PAID SERVICE
15
18
21
24
27
30
I
R
I
R
I
R
1
Engine Oil
2
Engine oil filter element
R
C
R
R
R
R
R
3
Engine sump filter (oil strainer)
C
C
C
C
C
C
C
C
C
C
Check level at every 1000 Kms or earlier as required
5
Magnetic drain plug under gear box and seconC
C
C
dary drain plug under crankshaft in crankcase RH C
Spark plugs (2 nos.)
C ,A C,A C,A C,A C,A
R
6
HT leads for crack
I
7
Carburetor (C.V. Type)
8
Fuel Tap / Filter
9
Fuel tank
4
I
I
I
I
I
C ,A C ,A C,A C ,A
I
I
I
I
R
I
*Clean, Inspect and Tune
C
C
C
C
C
C
C
C
C
C
C
10 Fuel hose / pipe
I
I
I
R
I
I
I
R
I
I
I
11 Accelerator & Carburetor cable play adjustment
A
A
A
A
A
A
A
A
A
A
A
12 Rubber hose, Air filter to Carburetor
I
I
I
I
R
I
I
I
R
I
I
A : Adjust
C : Clean
D : De-carbonise
I : Inspect
40
L : Lubricate
R : Replace
PERIODICAL MAINTENANCE
S.
No.
DESCRIPTION
FREE SERVICE
whichever is earlier
Kms (x 1000) 0.5
3
6
9
12
Months
1.5
3
6
9
I
I
I
I
13 Rubber hose, Adaptor
R
PAID SERVICE
15
18
21
24
27
I
I
I
R
I
14 Exhaust system
30
I
D
15 Air filter paper element
C
C
C
C
R
16 Inlet / Exhaust valve seating
C
C
C
R
C
I
17 Clutch lever free play
C
I
Check & Adjust every 1000 Kms or earlier as required
18 Cylinder head (Combustion chamber)
D
19 Hand levers & kick starter lever pivot
Lubricate every 1000 Kms or earlier as required
20 PAV pipes & hose clip
I
I
C
I
C
I
C
I
C
I
C
21 Rear brake pedal pivot
L
L
L
L
L
L
L
L
L
L
L
22 Battery terminals (apply petroleum jelly)
C
C
C
C
C
C
C
C
C
C
C
23 Battery Electrolyte level
I
I
I
I
I
I
I
I
I
I
I
24 Earth wire eyelet (behind battery carrier)
I
25 Front Fork oil / leak
A : Adjust
C : Clean
I
D : De-carbonise
I : Inspect
41
R
I
I
L : Lubricate
R
I
R : Replace
PERIODICAL MAINTENANCE
S.
No.
FREE SERVICE
whichever is earlier
Kms (x 1000) 0.5
3
6
9
12
DESCRIPTION
Months
1.5
3
6
PAID SERVICE
15
18
21
24
27
9
26 Rear wheel drive chain
Adjust for every 1000 Kms / Clean, Lubricate &
Adjustevery 3000 kms or earlier as required
27 Rear brake pedal free play
Adjust every 1000 Kms or earlier as required
28 Rear brake cam
L
29 Steering ball races / play adjustment
A
30 Spokes tightness & Wheel rim run out
I
L
L
A
I
R
L
A
I
31 Rear wheel cush rubbers
L
L
A
I
L
33 Tyre wear (Front & Rear)
R
L
A
I
I&R
32 Swing Arm pivot bush & spacer
30
L
I
I&R
L
L
R
L
I
I
I
I
I
I
I
R
I
34 Brake fluid (Disc brake)
I
I
I
I
R
I
I
I
R
I
I
35 Pivot-Side Stand, Center Stand, Pillion foot rest
L
L
L
L
L
L
L
L
L
L
L
A : Adjust
C : Clean
D : De-carbonise
I : Inspect
L : Lubricate
R : Replace
NOTE
For maintenance after 30,000 Kms, please repeat the same frequency levels specified above, in consultation
with a Royal Enfield Authorised Dealer / Service Point.
* Refer Service Manual.
42
MINOR MAINTENANCE TIPS
The following minor maintenance can be carried out
easily with simple tools. However, In case, if it is felt
that the adjustments are best done by an expert, we
recommend that the motorcycle be taken to a nearest
Royal Enfield Authorised Dealer / Service Point.
ENGINE OIL LEVEL INSPECTION
CONTROL CABLES, HANDLE LEVER, PIVOTS,
CENTER / SIDE STAND PIVOTS
MAX
MIN
Main & Side
Stand Pivot
Place motorcycle on its center stand on a firm
surface.
Lever Pivot
Warm up engine for a few minutes & switch off.
Lubricate after using the motorcycle in rain, after
water wash or if used in dusty conditions.
The level is correct if the oil level is in the middle
of the oil level window.
Wipe the area free of dirt / grease.
Apply a few drops of oil on the pivots.
Top up with recommended oil if required.
43
MINOR MAINTENANCE TIPS
ENGINE OIL CHANGE
Secondary
Drain Plug
Primary
Drain Cap
TILT VEHICLE
RH & LH
Primary
Drain Bolt
(Refer Periodical Maintenance Chart for frequency)
Place motorcycle on its center stand on a firm flat
surface.
Start engine and warm up for 2 minutes.
Keep a clean tray below the engine.
Remove the oil filter element on the Crankcase
Cover RH.
Remove primary drain cap, to drain oil & clean
suction filter, magnet.
Allow the oil to drain by tilting the motorcycle to
both sides.
Wash the primary and secondar y drain plugs
along with suction filter thoroughly and refit on
the crankcase after all the oil is drained out.
Then remove secondary drain plug to drain oil &
clean the magnet.
Finally remove primay drain bolt to drain the
complete oil.
44
MINOR MAINTENANCE TIPS
Soak a new oil filter element in the oil and refit
on the Crankcase Cover RH.
SPARK PLUG
Assembly 3 bolts and tighten them. Ensure ‘O’ Ring
and gaskets are taken seat properly.
C l eani ng a nd a djus ti ng gap (Refer Peri odic al
Maintenance Chart for frequency)
Fill recommendedoil
to engine till the oil
level is upto “M AX ”
level mark in the oil
wi ndo w i n C ran kcase Cover RH.
Remove HT Lead and
the spark plug f ro m
the cyl inde r head
usi ng
t he
p lug
spanner and tomm y
bar as shown in pic.
Clean the insulator tip
and electrodes of the
plug carefully using a
poi nted s cr aper or
spark plug cleaner.
Max
Min
NOTE
Replace o il filter elem ent whenever o il is bei ng
replaced.
Set the gap between
0.70 to 0.80 mm for
UR6DC & 0.80 to 0.90
mm for WQR8DC
CAUTION
Filling up oil over MAX mark may cause smoke and /
or loss of power. Do NOT allow oil level to fall below
MIN mark. Doing so may result in engine internal
damage or malfuncton.
Refit the spark plug on
the cylinder head and
connect H.T. Lead.
45
M10
M14
MINOR MAINTENANCE TIPS
BRAKE FLUID
INSPECTION OF TYRES AND WHEELS
Inspect the tyr e peri odically fo r tread wear,
cracks and cuts.
Check if oil is above ‘min’ level. To top up, remove
cover with diaphragm and top up with either DOT 3
or DOT 4 as specified.
Minimum tread depth :
Front tyre : 1mm
Rear tyre : 2 mm
Check and remove stone, splinters,
nails or other particles embedded in
the tyre treads.
MAX
MIN
Bald spots / swelling may be caused
by inte rnal dam age. Rep lace the tyr es , i f
defective.
Rep lace tyr es w hen the trea d depth has
reached the minimum as specified.
CAUTION
Periodically inspect wheels for spokes breakage
and wheel rim run out.
Please take care that it does not spill over any other
parts of the motorcycle. Please wipe the spilled brake
fluid immediately, if there is any spill over, using a
soft cloth (preferably a wet cloth) to avoid damage
to paint work or other parts.
Check proper seating of the tyre beading on
the rim whenever the tyre is reassembled.
Whenever a new tyre is installed, ensure rim and
spokes do not get damaged on account of using
wrong levers.
Don’t mix DOT 3 & DOT 4 Brake fluid together.
46
MINOR MAINTENANCE TIPS
Use o nl y standard tyres & tubes infl ated to
correct pressure.
FRONT WHEEL REMOVAL
Place the vehicle on center stand
Place a wooden block
th e fr o nt end of
engine to support the
vehicle.
TYRE PRESSURE
Solo
With Pillion
Frontt
Rear
1.41 kg/cm2
(20 PSI)
2.11 kg/cm2
(30 PSI)
1.55 kg/cm2
(22 PSI)
2.25 kg/cm2
(32 PSI)
Dis co nn ect
cable.
s peedo
Loosen the pinch bolt
on the RH fork guide.
Hol d fr ont ax le by
spanner and loo sen
axle nut then remove
nut along with washer.
WARNING
Tyres, rims and air valves must be correctly
matched to wheel rims. See your Royal Enfield Dealer.
Mismatching tyre, tubes, rims and air valves may
result in damage to the tyre bead during mounting,
allow tyre slippage on the rim and cause tyre failure.
47
MINOR MAINTENANCE TIPS
Tap and remove the front wheel spindle
FRONT WHEEL ASSEMBLY
Tilt the vehicle to RH Side and take out the wheel
along with speedo drive with bush & LH side spacer.
Remove the wooden piece / card board sheet
placed between the brake pads.
Pla ce
t he
b us h
sp eedo dr ive i n
positi on and place
speedo drive over it.
In sert the wheel
alo ng wit h speedo
drive assembly and
LH spacer between
the fr ont fo rk ends
ens ur ing the brake
di sc i s lo cat ed i n
between the brake
pads.
Take out Speedo drive
and bush on the RH
side as shown in pic.
CAUTION
Do not press the front brake lever when wheel is
removed as this will result in the brake pads coming
too far out of the brake caliper.
Place a 4 mm thick wooden piece or cardboard
sheet between the brake pads to avoid pads
activation in the event the front brake lever is
accidently pressed.
Ins ert and tap the
fr ont whee l ax l e
gently inside.
Refit the washer and
tighten the nut firmly.
48
MINOR MAINTENANCE TIPS
REAR WHEEL REMOVAL
Place the vehicle on center stand on a firm and
flat surface.
Note and mark the position of the chain adjuster
bu ttin g
wi th
t he
stopper on the right
side.
Remove split pin and
castle nut on the RH
side.
Tighten the pinch bolt on the RH fork guide.
Rotate the wheel and check for smooth rotation.
Remove wheel spindle
fr om LH s ide al ong
with chain adjuster,
tak ing care no t to
drop the wheel collar
and spacer from the
LH side of the wheel.
Connect the speedo cable to speedo drive unit
and rotate the wheel to check for proper working
of speedo meter.
Press brake lever 2 or 3 times to check front brake
efficiency.
Tilt vehicle to RH side
and s li de o ut r ear
wheel.
NOTE
Ensure that the speedo drive is correctly located such
that the cable can be connected without difficulty.
49
MINOR MAINTENANCE TIPS
Ensure that the chain adjuster knotch butts with
the stopper as appropriate when both the front
& rear wheels are aligned.
REAR WHEEL ASSEMBLY
Ensure the four cush rubbers are in position inside
the rear wheel hub.
Tig hten the cas tle
nut
fir m ly
and
ensure that the hole
o n ax le s ha ft a nd
the slot on castle nut
are
ali gned
to
en abl e s pl it p in
fitment.
Tilt vehicle to right
and i nsert wheel
assembly between
the swing arms.
Po s iti o n th e r ear
wh eel wi t h cu s h
rubber on the rear
chain sprocket.
Fix the split pin.
Hold wheel collar
and spa cer i n
position.
CAUTION
Do not force the spindle into the wheel as the threads
may get damaged. Tap it through the wheel gently.
A s s em b le
t he
whe el
s pind l e
alo ng with chai n
adjuster from the
LH side of vehicle
and gentl y tap it
through the wheel.
WARNING
Ensure the vehicle does not come off centre stand
whi le a ss em bli n g / dis a s sem bl in g th e wh eel
assembly. Failure to adhere could result in damage
or serious injury.
50
MINOR MAINTENANCE TIPS
ADJUSTMENTS - CLUTCH
DRIVE CHAIN FREE PLAY (PLAY 25 - 30 MM)
2 to 3 mm
Remove rear wheel
split pin.
A
B
Loo sen castle nut,
spindle nut, anchor
nut and brake rod
nut.
Clutch Lever (free play 2 to 3 mm)
CLUTCH FREE PLAY ADJUSTMENT
Loosen the cable outer lock nut (A).
Turn the RH adjuster
cam as
appr o priately, till 25 to 30
m m sla ckn es s is
achieved on the top
run of the chain.
Turn the Nut (B) Clockwise to reduce the play or
Anticlockwise to increase the free play.
Check free play 2 to 3 mm at Clutch lever pivot
on handle bar end.
Tighten lock nut (A) after adjustment is done.
51
MINOR MAINTENANCE TIPS
Check brake pedal free play, If necessary adjust.
CHECKING REAR BRAKE PEDAL HEIGHT
Check that the front
and rear wheels are
correctly aligned.
Turn the LH adjuster
cam appropriately,
to ali g n bo th t he
wheels.
C heck and ensure
that the knotches on
the cam are resting
o n the pi n in t he
swing arm on both
sides.
Loosen the lock nut.
A p ply bra ke a nd
tighten all nuts.
Turn in or out the pedal stop pin bolt till the brake
pedal and front footrest are in the same height /
level as shown in above pic.
Finall y To rque the
anchor Nut.
Tighten the lock nut
Check for free rotation of rear wheel.
52
MINOR MAINTENANCE TIPS
CHAIN LOCK FITMENT
REAR BRAKE PEDAL PLAY ADJUSTMENT
20 - 30 mm
Turn in or out the adjuster nut at the brake rod end.
The recommended brake pedal travel is 20-30 mm.
Check that the brake is not binding and the rear
wheel rotates freely.
The open end of the chain link master lock to face
opposite to normal direction of chain rotation as
shown pic.
WARNING
Please ensure brakes are adjusted to their maximum
efficiency. Inefficient brakes can cause an accident.
Please ensure adequate caution while applying brakes.
Sudden application OR pressing the levers fully can caused
the wheels to lock. This may cause the motorcycle to skid
with possible loss of control and result in an accident
causing. Brake shoes must be inspected for wear every 4000
Kms. If you ride under adverse conditions, (steep hills,
heavy traffic, etc.) a more frequent inspection at 1600 Kms
or less, is required.
WARNING
The fitment in wrong direction lock can lead to
falling off of chain link thus disengaging the drive.
This wil l lead to potentiall y hazardous situati on
which, if not avoided, could result in serious injury.
53
MINOR MAINTENANCE TIPS
Turn the adjuster such that the adjuster moves
up to increase the spring tension and vice versa
to reduce the spring tension.
ADJUSTMENT OF GAS FILLED SHOCKABSORBER
RH
A djus t both left hand and ri ght hand s hock
absorbers so that the same knotch rests on the
pin in both sides.
WARNING
Ri ding the m ot or cy cl e wit h th e kn otch es
adjus ted in different pos iti ons can cause lo ss of
control and may lead to an accident.
LH
The rear gas shock absorber is adjustable type i.e.,
the spring tension can be increased or reduced.
Increase the spring tension for high load operation.
Regularly inspect shock absorbers and front forks for
leaks. Replace worn parts. Worn parts can adversely
affect stability and handling.
Reduce the spring tension for low load operation.
NOTE
The adjuster provided on the bottom of the spring
has five knotches.
Ensure no fouling of any accessories with rear shock
abs or ber. C h eck f or s uf ficient gap avail abil ity
between the shock absorber and the attachments
when the rear end of the motorcycle is fully loaded
and the shock absorbers are fully compressed.
Insert special ‘C’ spanner on the bottom adjuster
and rotate to change knotch position.
54
MINOR MAINTENANCE TIPS
BATTERY MAINTENANCE
REMOVAL OF BATTERY ON VEHICLE
T he
veh icle
is
provided with 12V 14 AH battery.
The battery must be
periodically checked
for
Unlock (turn the key
anti clockwise) and
remove the battery
cover.
C l eanl i ne ss a nd
cor ro si o n
f r ee
terminals.
Electr o l yte lev el
m us t be abo ve
“MIN” level.
Remove the battery
holding two rubber
straps gently.
If electrolyte level
is lo w, r em o ve
caps and top up
with distilled water
only.
Pull out the battery
an d
t urn , th en
disconnect both the
ter m i na l
wi r es
(ne gati ve
a nd
positive respectively)
Apply petroleum jelly
o v er t he b atter y
ter m i na ls t o av oid
sulphation.
Take out the battery.
55
MINOR MAINTENANCE TIPS
WARNING
ASSEMBLY OF BATTERY ON VEHICLE
Always disconnect the negative (-) battery cable
fi rs t and then the Red pos iti ve (+) cable while
removing the battery connections.
Position the battery in the battery carrier such that
the negative terminal of the batter y is towards
fuel tap.
NOTE
Ensure ignition switch is in ‘OFF’ condition.
For checking the battery voltage and electrolyte
specific gravity, contact authorised Royal Enfield
service or battery service centre.
Connect the positive terminal (Red wire) first.
Connect the negative terminal (Black wire) next.
Smear the terminals with petroleum jelly. (Do not
use grease).
CAUTION
Refit the rubber strap bracket to hold the battery.
Do not use battery with low electrolyte level as
the battery internals cells will get damaged.
Refit LH side panel.
Do not overfill the battery electrolyte level as it
will spill out through the overflow pipe and cause
corrosion to vehicle parts.
NOTE
Clean the wire terminals free of corrosion and keep
the terminals coated with petroleum jelly.
Use only distilled water meant for use in batteries
to avoid damage to battery.
CAUTION
Electrolyte should not be filled when the level is
between minimum & maximum levels indicated
in battery as “MIN” & “MAX”.
Connect the +ve and -ve cables to the respective
batter y terminals. Failure to do so may result in
damage to the motorcycle electrical system.
56
MINOR MAINTENANCE TIPS
Remove rubber grommet
fr om the r ef lecto r
Assembly.
CHANGING ELECTRICAL COMPONENTS
HEAD LAMP BULB REPLACEMENT
Lo o sen the hea d la m p
holding top screw. Then
pul l out head lam p
assembly.
Gen tl y pr es s th e bu l b
holding ‘U’ clip from both
the sides downwards and
releas e it from reflecto r
slot as shown.
Detach bo ttom lug fr om
the head lamp ho us ing
body.
Pull out head lamp bulb
and inspect its filament for
fuse.
CAUTION
Di sco n nect hea d la m p
wir e co nnec to rs Gre en,
Ora nge and Blue co l o r
terminals.
Never to uch the bul b wi th
your fingers, Finger prints will
etch the glass and decrease
bul b lif e. A lways ho ld the
bulb with paper or clean dry
cloth during handling.
57
MINOR MAINTENANCE TIPS
Connect the wire couplers
as mentioned below.
ASSEMBLING THE HEADLAMP
Refix the new head lamp
hal ogen
bul b
in to
reflector unit by locating
the wide protrude on top
side mounting.
TOP SIDE: GREEN COLOUR
RIGHT SIDE: BLUE C OLOUR
LEFT SIDE: ORANGE COLOUR
Position the reflector ring
bottom lug into head lamp
cas ing slo t and sl ide it,
th en t i ght en t he t o p
mounting screw.
Fix bulb holding U clip into
ref l ect o r b o dy kno t ch,
then press the both ends of
clip and lock in its slot.
NOTE
After connecting above said procedure, turn ignition
switch to “ON” condition and then check, ensure that
flash light working in HIGH BEAM mode.
Fit the rubber grommet.
If you use the bulb other than specified rating (12V
55/60W) may result in over loading electrical system
lea d to pre m atu r e f ailu re o r fr eque nt b atte r y
discharge.
58
MINOR MAINTENANCE TIPS
TAIL LAMP BULB REPLACEMENT
TRAFFICATOR BULB REPLACEMENT
Remove the two nuts each
from RH & LH side of the
rear number plate holder.
Remo ve the 2 screws &
take out trafficator glass
cover.
Pul l ou t Ta il Lamp
as s em b ly a lo n g wi th
bracket and twist the bulb
holder in anticlockwise to
re m ove
bulb
holder
assembly.
Press bulb gently & Turn
anticlockwise to take out
the bulb.
Po s iti o n th e ne w bu lb
ins i de
the
ho ld er,
ensuring that the pins in
the bulb, match with the
slots in the holder.
Turn old bulb to remove
and replace with a new
bulb.
Refit the bulb holder and
turn clockwise to lock the
bulb holder.
Pres s the bulb and turn
clockwise to lock the bulb
in the holder.
Ref it the tai l la mp
wi th b rack et on t he
reverse order of removal
process.
Refit the trafficator cover
cu t s l o t m ar k faci ng
downwards and tighten
the 2 screws.
59
Cut Mark
MINOR MAINTENANCE TIPS
Replace the required fuse with the spare fuse
available in the fuse carrier.
FUSE
Open the LH tool box.
NOTE
Take out tool kit.
Please ensure to replace a spare fuse in the holder
at the earliest opportunity.
Remove fuse holder
rub ber & l i ft f us e
carrier top cover.
BLADE FUSE USAGE LIST
Fuse No.
4
Color
Remarks
1
Blue
Main Fuse (15A)
2
Red
Ignition Fuse (10A)
3
Red
Spare Fuse (10A)
4
Blue
Spare Fuse (15A)
3
2
1
60
MINOR MAINTENANCE TIPS
Tap the filter element
to r em o ve d ust as
sh o wn and cle an
tho ro ug hl y befo r e
assembly.
AIR FILTER PAPER ELEMENT CLEANING/REPLACEMENT
Insert the key, turn
an ti cl okw ise to
remove RH side air
filter box lid.
Clean both intake
adaptors and duct as
shown in pic.
Loo sen the fil ter
hol di ng nut by
10mm spanner as
shown in pic.
Assemble the filter
element and cover in
the reverse order of
dismantling process.
Rem o ve the nut,
washer and co ver
air filter to take out
air filter element.
Please ensure proper
sealing of cover plate
against air filter
element.
61
WASHING PROCEDURE
AFTER WASHING
PRECAUTIONS
Wash vehicle when the engine is cold.
Cover the silencer tail end and control switches with
suitable plastic bags and tie it firmly to prevent
water entry into them.
Remove ignition key and seal key hole using
adhesive tape.
Use a suitable engine degreaser, available with
your local parts store, to remove dirt or grease from
the engine external parts if required. Follow the
directions in the label carefully before using the
degreaser.
Use low pressure jet of water to clean the entire vehicle.
Never spray water with great force on head lamp,
speedometer, trafficator lights, front and rear wheel
hubs, electrical connections and wires, control
cables, sparkplug, battery, etc.
Use luke warm water and mild detergent on the
painted components to remove dirt, etc.
Rinse vehicle thoroughly with plain water to remove
the detergent and wipe vehicle dry.
If possible, use compressed air and blow off water
particles from the obscure areas of the vehicle,
electrical connections etc.
Ensure, the vehicle is thoroughly dry by wiping with
a clean soft absorbent cloth or chamois leather.
Remove all plastic bags and adhesive tapes.
Lubricate control cables, pivot and rear chain with
lube oil
Polish the painted and plated surfaces using
polishing wax.
Start the bike allow engine to idle and warm up.
Drive the motorcycle slowly, applying both brakes
intermittently to dry up the brake shoes.
Test brakes for full efficiency.
WARNING
Observe warnings and cautions given on labels
of cleaning compounds.
When washing your motorcycle, be careful not to get
the brakes, engine, mufflers or air cleaner etc., too
wet.
62
STORAGE PRECAUTIONS
Rem o ve bat ter y f ro m t he b ike. C le an t he
terminals free of corrosion.
Incase your Motorcycle is not going to be used for a
month or more, we advise the following precautions
to the taken.
Maintain electrolyte level between max or min
mark, by adding distilled water and wipe the
battery dry.
Carryout required repair / adjustments on the
motorcycle.
Sto r e t he b atter y i n a co ol , dr y an d wel l
ventilated place.
Wash the motorcycle thoroughly and lubricate as
per the maintenance chart.
Do not place the battery in direct sun light, near
open flame or where temperature is above 40 oC
or below 0 oC
Start the engine, warm up for a few minutes and
switch off.
Drain out the fuel completely from the fuel tank
and fuel lines.
Cover the silencer with plastic bags to prevent
moisture entry. Set the motorcycle on its center
stand.
Remove spark plug. Pour in about 25ml of clean
engine oil through spark plug hole. Close the hole
an d cr ank engi ne s ever al t im es and r ef i t
sparkplug.
Apply anti rust solution on all chrome pl ated
par ts. Take care not to apply this solution on
rubber or painted parts.
Store motorcycle in a clean covered area free of moisture and keep it covered to prevent dust
settling on it.
Clean rear chain thoroughly and apply a thin
film of lube oil.
63
STORAGE PRECAUTIONS
Remove spark plug on cylinder head and pour
PREPARING THE MOTORCYCLE FOR RE USE
in a few drops of engine oil. Crank engine a few
Remove anti rust solution from all chrome plated
ti mes to lubricate cylinder walls and piston.
parts and clean the motorcycle.
Clean spark plug and refit.
Inflate the tyres to the correct tyre pressure.
Switch “ON” ignition switch.
Ens ur e batter y i s fully charged and pr oper
Star t vehicle and warm up engine fo r a f ew
electrolyte level is maintained.
minutes before riding the vehicle.
Connect the battery.
Lubricate all control cables and pivots.
Check proper level of oil in engine.
NOTE
Do not raise the engine rpm the moment it is started,
but allow the engine to run at idling speed.
Fill fuel tank with fresh petrol.
Check fuel line / hose for any cracks or cuts.
CAUTION
Clean the air filter.
Proper long-term storage is important for the safe,
tr oubl e-fr ee o per a tio n of your Roy al E nfie ld
motorcycle.
Remove plastic covering from the silencer.
64
LONG TRIP PRECAUTIONS
CHECKS PRIOR TO THE COMMENCEMENT OF
LONG JOURNEY
ITEMS TO BE CARRIED
Tool kit.
Ser vice the m otor cycle tho ro ughly at Ro yal
Enfield Authorised Dealer / Service Point as per
periodical maintenance chart. (Ref. Page No. 40,
41 & 42)
First aid kit.
Bulbs for Headlight, Trafficator light, Rear Tail
Lamp and Fuse (10 & 15 Amps).
Sufficient quantity of petrol in the fuel tank for
the journey planned.
Accelerator, Clutch and Speedo Cable.
Check and correct tyre pressure if necessary.
Rear chain master link lock assembly.
CHECKS AFTER EVERY 1500 KMS OF RUN
Tightness of all fasteners.
Spare tube, puncture repair kit - cold vulcanising
Tyre tread condition and wear of tyres.
type.
Battery condition and electrolyte level.
Foot operated Air Pump.
Correct oil level in engine.
Insulation tape.
Working of all lights and horn.
Proper drive chain tension.
Spark plugs (M14 & M10), Fuel hose.
65
CARING FOR MILEAGE
Both lower and higher road speeds cause low
kilometers per litre of petrol.
STOP THE DROP THAT LEAKS
Petrol leak at a rate of one drop per m inute
accumulates to 5,25,600 drops a YEAR! That is, 35
ltrs of Petrol.
PERFORM PREVENTIVE MAINTENANCE AS PER
RECOMMENDATIONS
Petrol leaks cause raw petrol smell. Get the leaks
arrested immediately.
REGULAR PREVENTIVE MAINTENANCE ENSURES
Correctly inflated tyres.
USE RECOMMENDED FUELS AND OILS ONLY
Fasteners tightened to correct torques.
Wrong grade or adulterated petrol does not burn
fully and results in heavy smoke, high rate of
car bo n depos iti on i n cylinder and exhaus t
system and low mileage.
Freely moving engine & transmission components.
Properly tuned and adjusted engine.
CUT OFF NEEDLESS LOW IDLING
Wrong grade and inferior quality oils do not
lub rica te w ell. T he m ov ing part s we ar
prematurely.
Ten minutes of low idling wastes 70 ml. of petrol. So
cut off the engine when you know you have to wait
for one minute or more.
Always use recommended fuel (unleaded > 87
octane petrol) and oils only.
STOP
Revving : Ten revvings wastes 20 ml. of petrol
RIDE AT COST EFFECTIVE SPEED
Racing starts : Ten racing starts wastes 150 ml.
of petrol.
Cost effective speed (in top gear) is 45 to 50 Km
per hour.
66
CARING FOR MILEAGE
Sudden acceleration : Ten sudden accelerations
wastes 100 ml. of petrol.
For better mileage, use front and rear brakes
simultaneously when absolutely needed. Control
vehicle speed with throttle and gear like smart
riders always do.
STOP BRAKE RIDING
Brake riding pushes the brake shoes to come in
contact with revolving drum. To overcome the
resulting frictional load, engine burns additional
petrol.
AVOID OVER LOADING
Over loading tyres the engine, wears the parts
faster and reduces mileage.
Result : Low mileage, loss of power, faster wear
of brake shoes and drum.
PARK YOUR VEHICLE IN SHADE WHEN NOT IN USE
Petr ol is highl y volatile. It evaporates under
no r m al
atm os ph er ic te m per atur e. T he
evaportion increases with temperature. Prevent
this loss by always parking your vehicle under
shade.
NEVER CLUTCH RIDE
Clutch riding slips the clutch & engine drive does
not get totally transferred to the rear wheel.
Besides low mileage, clutch riding ends up with
burnt friction plates of clutch, loss of power and
engine overheating.
Too few Kms running per day allows more time
for evaporation affecting the mileage.
AVOID FREQUENT BRAKING
Braking arr ests the ro ad s peed. M otorcycl e
momentum is reduced. Additional fuel is burnt
for subsequent acceleration.
67
COMPLETE WIRING DIAGRAM - BULLET 500
NOTE : Complete Wiring Diagram is attached on this page.
VEHICLE STARTING PROCEDURE
BASIC GUIDELINES TO BE FOLLOWED “FOR ALL ELECTRIC START VEHICLES”
1.
In cold condition of the engine or for initial start, it is advised to use electric start (ES) only.
2.
Apply choke in cold start condition. (ambient temperature <25° C)
3.
DO NOT ATTEMPT – “HALF START” BY CASUALLY PRESSING ELECTRIC START BUTTON.
4.
PLEASE PRESS AND HOLD ELECTRIC START BUTTON FOR ATLEAST 3 SECONDS CONTINUOUSLY FOR
THE CRANKING OR UNTIL THE ENGINE FIRES AND SUSTAINS, WHICHEVER IS EARLIER.
5.
If engine doesn’t start in the first attempt, release the ES button and repeat the above Procedure.
6.
It is advised not to apply excessive throttle during starting.
68
D
C
B
LIGHT GREEN
NEUTRAL SWITCH
PILOT LAMP
LIGHT GREEN
BROWN
LH
10W FRONT
TRAFFICATORS
RH
2x6.3MM
COUPLER
IGNITION
SWITCH
OFF
POSITION
SPEEDOMETER ASSY
9x2.8 COUPLER
PILOT
LAMP
POSITION
LAMP 4W
HEAD LIGHT
60/55W
HALOGEN BULB
CLUTCH SWITCH
E START
H.LAMP
BLACK
F
E
H
9x2.8
COUPLER
GREY
GREY
A
GREY
BLACK
BLUE
GREEN
BLACK
YELLOW/RED
YELLOW
GREY
GREEN
RED/WHITE
RED/WHITE
GREY
KILL
B/G
PARK
B/W
RED/WHITE
LIGHT GREEN
BLACK
RED
BLACK/WHITE
BLACK
HORN HT
HORN
8
2
9
4
3
1
RED/WHITE
BLACK/RED
BLACK/RED
RED/WHITE
RED/WHITE
GREY
HORN LT
6
7
HB/LB
TRAFFIC
5
9x2.8
COUPLER
BLACK
BROWN
4x6.3 COUPLER
BLACK
G
BLUE
AMMETER
ASSEMBLY
BLACK/GREEN
RED/WHITE
GREY
GREY
FRONT
BRAKE
SWITCH
RED/YELLOW
RED
WHITE
RED
BLACK/WHITE
BLACK/GREEN
SWITCH
MODULE LH
YELLOW/WHTE
SWITCH MODULE RH
B/W
BLACK
RED
RED
RED
2x6.3
‘L’ TYPE
COUPLER
12V 14Ah
BATTERY
MAX
MIN
FUSE -2
15A
FLASHER
RED/WHITE
GREEN
BLACK
BLACK
FUSE-1
10A
2x6.3 COUPLER
RECTIFIER
REGULATOR UNIT
(THREE PHASE)
BROWN
BLACK
B/G
GREY
BLACK/WHITE
RELAY STARTER
R/B
SPARK
PLUG (M10)
SPARK
PLUG (M14)
4x2.3
WATER PROOF
COUPLER
VIOLET
BLACK/WHITE
BLACK
TRAFFICATOR
REAR LH 10W
STOP/TAIL
LIGHT
21/5W
3x2.8 COUPLER
TRAFFICATOR
REAR RH 10W
0.9 KW STARTER
MOTOR
BROWN
2x2.3 WATER PROOF
COUPLER NATURAL
3x2.3
THROTTLE WATER PROOF
POSITION COUPLER
SENSOR
6x2.8 COUPLER
IGNITION
COIL 2
IGNITION
COIL 1
BLACK/GREEN
WHITE/RED
BROWN
RED
2x2.3
WATER
PROOF
COUPLER
TCI UNIT
2x2.3
WATER PROOF
COUPLER
BLACK
BLUE/WHITE
LIGHT GREEN
2x2.3
WATER PROOF
COUPLER
WHITE
REAR BRAKE
SWITCH
WHITE/RED
BLACK
2x2.8
COUPLER
RED
YELLOW
YELLOW
BROWN
YELLOW
RED/WHITE
THREE
PHASE
MAGNETO
1T
BLACK
3x6.3 COUPLER
GREEN
BLACK
GREEN
PULSER
COIL
BLACK
WHITE
BLACK/GREEN
GREY
GREEN/WHITE
COMPLETE C
WIRING
O M P DIAGRAM
L E T E W- IBULLET
R I N G500
DIAGRAM
BLADE FUSE LIST
Fuse 1
TCI FUSE
IGNITION LOADS
Fuse 2
Fuse 3
Fuse 4
TROUBLE SHOOTING
CAUSES
REMEDIES
I. ENGINE FAILS TO START
1)
Ignition switch in ‘OFF’ Position ...............................................
Switch on ignition.
2)
Engine Stop switch in ‘OFF’ Position .......................................
Push stop switch to ‘ON’ position.
3)
Clogged fuel line / tap ..............................................................
Clean the fuel line / tap.
4)
Vent hole clogged in fuel tank cap .......................................
Clean vent hole.
5)
Fuse blown ....................................................................................
Check and Replace (Ref. Page No. 60)
6)
Carburetor passage & jets blocked .......................................
*Dismantle carburetor & clean jets
.........................................................................................................
/ passages
7)
Carburetor float stuck in closed position .............................
Ensure correct movement of float
8)
Spark plug cap / lead not connected ...................................
Fix cap / lead firmly
9)
Loose HT connections ................................................................
Fix connections firmly
10) HT Lead Damaged .....................................................................
*Replace HT Lead
11) Spark plug electrode dirty / fouled ........................................
Clean spark plug & Reset gap.
12) Spark plug insulation cracked ...............................................
Replace spark plug
* Contact Authorised Dealer / Service Point
69
TROUBLE SHOOTING
CAUSES
REMEDIES
13) Poor compression
- Auto Decompressor not working ..........................................
.........................................................................................................
*Ensure free motion of flyweight in exhaust
cam gear assembly
- Loose spark plug ......................................................................
*Tighten spark plug.
14) Clutch slipping ............................................................................
*Adjust clutch cable free play
II. ENGINE MISFIRING
1)
Water in petrol tank/carburetor ..............................................
.........................................................................................................
*Clean carburetor / petrol tank. Fill tank
with fresh petrol.
2)
Leak through intake hose ........................................................
.........................................................................................................
Tighten rubber hose suitably.
Replace if necessary
3)
Loose spark plug cap ................................................................
Fix cap / lead firmly
4)
Spark plug fouled/insulation broken ....................................
Clean / reset gap or, replace.
5)
Poor Compression .......................................................................
*Auto decompressor sticky or not working
6)
Loose electrical connections / coupler .................................
*Battery cable / fuse carrier / coils / TCI unit / Switch
* Contact Authorised Dealer / Service Point
70
TROUBLE SHOOTING
CAUSES
REMEDIES
III. ENGINE STARTS, BUT RUNS IRREGULARLY & STOPS
1)
Faulty fuel supply ......................................................................
Clean the fuel line / tap / vent hole
2)
Very low idling speed ................................................................
Increase idling speed
IV. POOR PICKUP
1)
Accelerator cable free play excessive ..................................
Adjust cable free play
2)
Faulty fuel supply .......................................................................
Clean the fuel line / tap / vent hole
3)
Choked air filter ..........................................................................
Clean / Replace air filter
4)
Loose carburetor mounting .....................................................
Tighten clamps firmly
5)
Brakes adjusted too tight ..........................................................
*Re-adjust properly
6)
Rear chain adjusted too tight .................................................
*Re-adjust properly
7)
Clutch Slipping ............................................................................
*Adjust clutch cable free play
8)
Under inflated tyres ...................................................................
*Inflate to correct pressure
* Contact Authorised Dealer / Service Point
71
TROUBLE SHOOTING
CAUSES
REMEDIES
V. WHITE/BLUE SMOKE
1)
Oil level in tank above the middle line in the ....................
oil level window
*Check and drain excess oil
2)
Worn out valve oil seal ..............................................................
*Check / Replace
3)
Worn out piston ring / cylinder ................................................
*Check / Replace
VI. ENGINE OVERHEATING
1)
Cylinder fins not clean ..............................................................
Clean the cylinder fins at regular intervals
2)
Clutch slipping ............................................................................
*Check and correct
3)
Suction leakage ..........................................................................
*Check and correct
4)
Incorrect carburetor adjustments ..........................................
*Check and correct
VII. EXCESSIVE FUEL CONSUMPTION
1)
Fuel leakage ................................................................................
*Check and rectify
* Contact Authorised Dealer / Service Point
72
TROUBLE SHOOTING
CAUSES
REMEDIES
2)
Worn out carburetor jets ...........................................................
*Change the defective jets
3)
Incorrect carburetor adjustments ..........................................
*Check and adjust correctly
4)
Choked air filter ..........................................................................
Clean / Replace
5)
Poor compression .......................................................................
.........................................................................................................
*Auto decompressor sticky or
not working properly
6)
Under inflated tyres ...................................................................
Inflate to correct pressure
VIII. IGNITION KNOCK
1)
Carburetor adjusted too lean .................................................
*Check and readjust
2)
Suction / intake system leakage .............................................
*Check and correct
IX. BRAKES POOR
1)
Not adjusted properly ...............................................................
*Adjust properly
2)
Oil / grease on lining or drum or disc ...................................
*Clean and refit
* Contact Authorised Dealer / Service Point
73
TROUBLE SHOOTING
CAUSES
REMEDIES
3)
Linings worn / Uneven wear ....................................................
*Replace linings
4)
Drum scored / Uneven wear ....................................................
*Rectify or Replace drums
X. VEHICLE WOBBLES
1)
Wheel rim runout ........................................................................
*Rectify
2)
Loose / Broken spokes ................................................................
*Tighten / Replace spokes
3)
Tyres not fitted correctly ............................................................
*Refit tyres correctly
4)
Wheels misaligned .....................................................................
*Ensure proper alignment
5)
Under inflated tyres ...................................................................
Inflate to correct pressure
XI. ELECTRICALS
Bulbs do not glow
1)
Loose / improper connection ..................................................
*Check and correct
2)
Bulb fused .....................................................................................
*Replace bulb
3)
Fuse blown ....................................................................................
Replace fuse
4)
Switch defective ..........................................................................
*Replace switch
* Contact Authorised Dealer / Service Point
74
TROUBLE SHOOTING
CAUSES
REMEDIES
Horn not working
1)
Loose connections ......................................................................
*Check and correct
2)
Requires tuning ...........................................................................
*Tune horn
3)
Switch Defective ..........................................................................
*Replace
4)
Fuse blown ....................................................................................
Replace fuse
Trafficators not working
1)
Loose / improper connections .................................................
Check and correct
2)
Bulb fused / Fuse blown ............................................................
Replace
3)
Switch defective ..........................................................................
*Replace
4)
I.C. Flasher defective .................................................................
*Replace
Brake light remains “ON”
(1) Switch not adjusted properly ..................................................
*Adjust switch properly
(2) Switch sticky .................................................................................
*Replace switch
* Contact Authorised Dealer / Service Point
75
TROUBLE SHOOTING
CAUSES
REMEDIES
XII. ELECTRIC START
VEHICLE NOT STARTING
(1) Neutral indicator not glowing ................................................
Bring the vehicle in neutral
(2) If vehicle is without neutral indicator ...................................
Press the clutch lever & start switch together
(3) Loose Connection .......................................................................
*Check & Correct
(4) Starter relay not working ..........................................................
*Check & Replace
(5) Malfunctioning of clutch switch .............................................
*Check & Replace
(6) Malfunctioning of Starter switch ............................................
*Check & Replace
(7) Battery discharge .......................................................................
*Check & Recharge
(8) Motor not working ......................................................................
*Check & Replace
(9) Battery not fully charged ..........................................................
*Check & charge
(10) Failure of sprag clutch ..............................................................
*Check & replace
* Contact Authorised Dealer / Service Point
76
WARRANTY TERMS & CONDITIONS
Royal Enfield Motor Cycles are manufactured by following best Quality practices in respect of the material and
workmanship.
Royal Enfield (RE) warrants Bullet 500 Motorcycle to be free from manufacturing and material defect under normal
use subject to following conditions.
1.
RE will replace or repair defective part / parts at their Authorised Dealer / Service point, free of charge within
a period of 12 months from the date of sale (date of Installation) or 10,000 kms whichever occurs earlier.
2.
The warranty is applicable only to first registered owner.
3.
The warranty shall be applicable only if all the free services are availed at the respective period / kilometer
range as per the schedule given in the owner’s manual from Authorised Dealer / Service Point.
4.
During the warranty period, RE’s obligations shall be limited to repairing / replacing free of charge such part
or parts of the vehicle, which on examination to have manufacturing defect. Such defective part / parts which
have been replaced becomes property of RE.
5.
Cost of oil, oil filter, fuel and other consumables are chargeable to the customer.
6.
Claims on proprietary items like tyres, tubes, spark plug, battery etc. should be taken up with respective
manufacturer or their authorised agents in the area directly by customer. RE shall not be liable in any manner
to replace them though their Dealers will provide assistance in preferring such claims on their manufacturer.
7.
Warranty shall not apply to:
(a) Normal ageing, detoriation or rusting of plated parts paints coat, rubber parts, soft items, glass items,
plastic parts etc.
77
WARRANTY TERMS & CONDITIONS
(b) Components like fuel filter, oil filter paper element, control cables, brake shoes / brake pads, clutch
plates, drive chain & sprocket kit, which are subjected to normal wear and tear.
(c) Damages due to use of lubricant / oil / grease etc. other than specified by RE.
(d) Damages due to use of non-genuine parts.
(e) Damages due to lack of proper maintenance of the vehicle.
(f ) Damages due to incorrect driving or riding habits.
(g) Parts damaged due to accidents, collision, abuse etc.
(h) Irregularities not recognized as affecting the quality or function of the vehicle such as slight vibration,
oil leakage, discoloration of exhaust bent pipe / silencer / soft, hard shock absorber etc.
(i)
Defects arising from fitment of unauthorised / additional Electrical loads.
(j)
Vehicle serviced / repaired at unauthorised service points.
(k) Vehicle used for competition / racing.
(l)
Electrical component like bulbs, fuses etc.
(m) Normal maintenance operations like adjustment of brakes, cleaning fuel system, engine tune up and
other such adjustments
8.
RE reserves the right to finally decide on all warranty claims
9.
RE reserves the right to make changes in Design of the vehicle without any obligation to install these changes
on previously supplied vehicles.
78
EMISSION WARRANTY
In compliance with the provisions of Rule 115(2) of the Central Motor Vehicle Rules, 1989, Royal Enfield certifies
that the following warranty is applicable to those components liable to affect the emission of the gaseous pollutants
in its range of motorcycles, in normal use to which it may be subjected to.
This emission warranty comes into force from 01st July 2001 and is valid for a period of 30,000 Kms. or 36 months,
whichever occurs earlier, from the date of sale to the first customer and is in addition to and parallel to the
warranty policy, conditions and obligations laid down in the Owner’s Manual.
Royal Enfield further warranty that if on examination by its Authorised Dealer / Service Point, the motorcycle fail to
meet the specified emission standards, then the Authorised Dealer / Service Point shall take necessary corrective
measures and shall at its sole discretion, repair or replace free of charge such components of the emission control
system to meet the required emission standards.
The method/s of examination to determine the warranty conditions of the emission warranty related components
will be at the sole discretion of Royal Enfield and / or our Authorised Dealer / Service Point and results of such
examination will be final and binding. If on examination the warranty conditions of the part/s is/are not established,
Royal enfield will have the right to charge all, or part of the cost of such examination to the customer in addition
to the cost of the components.
In case of acceptance of the component/s under Emission warranty, Royal Enfield will replace free of charge, the
component/s as required. However, the consumables like fuel, lubricants, solvents, etc shall be chargeable to the
customer as per actual.
In case any of the components covered under emission warranty or the associated parts, are not independently
replaceable. Royal Enfield will have the sole discretion to replace either the entire assembly or parts of the assembly,
through suitable repairs.
Royal Enfield reserves the right to carry out necessary consequential repairs to the motorcycle or replace any
part, in addition to the repair or replacement of the components covered under emission warranty, to establish
compliance to in-use emission standards. Such repairs / replacements will be chargeable to the customer.
79
EMISSION WARRANTY
All parts removed for replacement under warranty will become the property of Royal Enfield.
Royal Enfield will not be responsible for the cost of transportation of the motorcycle to the nearest Authorised
Dealer / Service Point OR for any loss due to non availability of the motorcycle during the period of examination
and repairs by Royal Enfield and / or their Authorised Dealer / Service Point.
Royal Enfield will not be responsible for any penalties that may be charged by statuatory authorities on account
of failure to comply with the in-use emission standards.
That cost/s incurred to check emission of the motorcycle will have to be borne by the customer.
Emission warranty will be applicable irrespective of the change of ownership of the vehicle provided all the
conditions as laid down in this document are met from the date of original sale of the motorcycle.
THE WARRANTY SHALL APPLY IF THE CUSTOMER
Observes all the important instructions and any other precautions listed in the owner’s manual.
Under all circumstances uses lubricants and fuel as recommended by Royal Enfield.
Regularly obtains and carries out maintenance in accordance with Royal Enfield guidelines and enters the
details in the Log book.
Immediately approaches the nearest Authorised Dealer / Service Point upon discovery of failure to comply
with the IN-USE emission standard inspite of having maintained and used the vehicle in accordance with the
instructions in the owner’s manual and having carried out such repairs and adjustments as may be required
with a view to establish such compliance.
Produces the ‘Pollution Under Control’ certificate valid for the period immediately preceding the test during
which the failure is discovered, the test having been carried out either for obtaining a new certificate or
80
EMISSION WARRANTY
pursuant upon being directed by an officer as referred to in sub rule (2) of rule 116 of the Central Motor
Vehicles Rules (CMVR).
Produces the owner’s manual and Log book for verification details.
Produces receipts covering maintenance of the motorcycle is specified in the owner’s manual from the date
of original purchase of the vehicle.
Produces valid certificate of Insurance and R.T.O Registration Certificate (RC Book).
THE EMISSION WARRANTY SHALL NOT APPLY IF
A valid “Pollution under control” certificate is not produced.
The motorcycle is not serviced by Authorised Dealer / Service Point as per the service schedule described in
the maintenance chart.
The motorcycle has been subjected to abnormal use, abuse, neglect and improper maintenance or has met
with an accident.
Replacement parts not specified and approved by Royal Enfield have been used.
The motorcycle, or parts thereof, has been altered, tampered with or modified or replaced in an unauthorised
manner.
The odometer is not functioning or the odometer and / or its reading has been changed / tampered with, so
that the actual distance covered cannot be readily determined.
The motorcycle has been used for competitions, races, and rallies or for the purpose of establishing records.
On examination by Royal Enfield or its Authorised Dealer / Service Point, if the motorcycle shows that any of
the conditions stipulated in the Owner’s manual with regard to use and maintenance have been violated.
81
EMISSION WARRANTY
The motorcycle has been run on adulterated / leaded fuel or lubricant other than those specified by Royal
Enfield in the Owner’s manual or any other document given to the customer at the time of sale of the motorcycle.
The emission related components are tampered with.
All service and parts related bills and vouchers incurred during the tenure of the emission warranty is not
produced.
All maintenance activities carried out on the vehicle during the tenure of the emission warranty is not entered
in the log book.
TIPS TO BE ON THE RIGHT SIDE OF LAW
Always get your vehicle checked to meet the emission regulations through and authorised emission checking
center.
Always carry a valid ‘Pollution Under Control’ certificate with you at all times during the validity of the emission
warranty (30,000 Kms / 3 years from the date of first sale)
TIPS TO REDUCE POLLUTION
1.
Ensure that the periodical maintenance is carried out as stipulated in the owner’s manual through a Royal
Enfield Authorised Dealer / Service Point.
2.
Use only Unleaded petrol (> 87 Octane) from reputed fuel pumps.
3.
Ensure the fuel used is not adulterated.
4.
Use correct spark plug as recommended in the owner’s manual.
5.
Use lubricants as per recommendations given on grade / brand in the owner’s manual.
82
ALL INDIA ROAD SIGNS
MANDATORY SIGNS
CAUTIONARY SIGNS
INFORMATION SIGNS
83
FREE SERVICE COUPONS
It is our endeavour to provide excellent service to your Royal Enfield Motor Cycle at all times. Towards this we
provide four free services at specific Intervals.
Please avail these services at the specified time, in any of the Royal Enfield Authorised Dealer / Service Point
nearest to you and as a token of satisfactory service, kindly return the free service coupon duly filled in and
signed, to the service outlet.
Availing the free services in the specified time is a prerequisite to warranty consideration.
84
1ST FREE SERVICE
1ST
FREE
SERVICE
500 KMS OR 45+8 DAYS WHICHEVER IS EARLIER FROM DATE OF SALE
Customer Name :
Dealer Code :
Address :
500 Kms
or
45+8 days
whichever is
earlier from the
date of sale
Frame No:
Regn. No:
Engine No:
Sale Date:
Vehicle Installation Form No.
Serviced Date:
ODO Reading :
Serviced by
(Dealer’s/ASP Name & Address)
Enter the Details
in Free Service
Record
Sold by (Dealer’s Name & Address)
(Cost of oil,
oil filter element
and other
consumables
used are
chargeable to
the customer)
Received the above vehicle after the service having been done to my entire satisfaction.
Customer’s Signature : .................................
Contact Phone / Mobile No.:
85
Date :
1ST FREE SERVICE ACTIVITIES
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
Water wash the vehicle and dry it with a clean cloth
Electrolyte ......................................................
Check level & top-up
Battery terminals .........................................
Clean and apply petroleum jelly
Drive chain free play .................................
Check, clean, lubricate & adjust
Rear brake pedal pivot ............................
Lubricate
Rear brake ....................................................
Adjust
Wheel rims front & rear .............................
Check spokes tightness
Front & Rear brake .....................................
Check & Adjust
Front fork oil leak .........................................
Check for leakage
Air filter element ..........................................
Clean
Spark plugs (2 Nos) ....................................
Check, clean & adjust gap
H.T. Leads ......................................................
Inspect for cracks
Carburetor ....................................................
Drain & Tune
Fuel filter ........................................................
Clean
Fuel hose ........................................................
Inspect for cracks
Rubber hose, Air filter to carburetor .....
Inspect for cracks
Accelerator cable .......................................
Check & adjust play
Clutch cable ..................................................
Adjust play
Engine oil sump strainer ...........................
Clean
Engine oil .......................................................
Replace
Engine oil filter element .............................
Replace
Hand levers & kick starter pivot ..............
Lubricate
86
CUSTOMER
COPY
Job Card No:
Date :
Odo Reading :
Name of Dealer/
ASP with Code:
..........................
..........................
ASP / Dealer’s
Stamp &
Signature
2ND FREE SERVICE
2ND
FREE
SERVICE
3000 KMS OR 90+15 DAYS WHICHEVER IS EARLIER FROM DATE OF SALE
Customer Name :
Dealer Code :
Address :
3000 Kms
or
90+15 days
whichever is
earlier from the
date of sale
Frame No:
Regn. No:
Engine No:
Sale Date:
Vehicle Installation Form No.
Serviced Date:
ODO Reading :
Serviced by
(Dealer’s/ASP Name & Address)
Enter the Details
in Free Service
Record
Sold by (Dealer’s Name & Address)
(Cost of oil,
oil filter element
and other
consumables
used are
chargeable to
the customer)
Received the above vehicle after the service having been done to my entire satisfaction.
Customer’s Signature : .................................
Contact Phone / Mobile No.:
87
Date :
2ND FREE SERVICE ACTIVITIES
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
Water wash the vehicle and dry it with a clean cloth
Electrolyte ......................................................
Check level & top-up
Battery terminals .........................................
Clean and apply petroleum jelly
Drive chain free play .................................
Check, clean, lubricate & adjust
Rear brake pedal pivot ............................
Lubricate
Rear brake ....................................................
Adjust
Wheel rims front & rear .............................
Check spokes tightness
Front & Rear brake .....................................
Check & Adjust
Front fork oil / leak .......................................
Check for leakage
Air filter element ..........................................
Clean
Spark plugs (2 Nos) ....................................
Check, clean & adjust gap
H.T. Leads ......................................................
Inspect for cracks
Carburetor ....................................................
Drain & Tune
Fuel filter ........................................................
Clean
Fuel hose ........................................................
Inspect for cracks
Rubber hose, Air filter to carburetor .....
Inspect for cracks
Accelerator cable .......................................
Check & adjust play
Clutch cable ..................................................
Adjust play
Steering free play .......................................
Check & Adjust
Engine oil .......................................................
Check level & top-up
Hand levers & kick starter pivot ..............
Lubricate
Clean
Oil filter element, oil strainer & magnetic drain plugs.
88
CUSTOMER
COPY
Job Card No:
Date :
Odo Reading :
Name of Dealer/
ASP with Code:
..........................
..........................
ASP / Dealer’s
Stamp &
Signature
3RD FREE SERVICE
3RD
FREE
SERVICE
6000 KMS OR 180+15 DAYS WHICHEVER IS EARLIER FROM DATE OF SALE
Customer Name :
Dealer Code :
Address :
6000 Kms
or
180+15 days
whichever is
earlier from the
date of sale
Frame No:
Regn. No:
Engine No:
Sale Date:
Vehicle Installation Form No.
Serviced Date:
ODO Reading :
Serviced by
(Dealer’s/ASP Name & Address)
Enter the Details
in Free Service
Record
Sold by (Dealer’s Name & Address)
(Cost of oil,
oil filter element
and other
consumables
used are
chargeable to
the customer)
Received the above vehicle after the service having been done to my entire satisfaction.
Customer’s Signature : .................................
Contact Phone / Mobile No.:
89
Date :
3RD FREE SERVICE ACTIVITIES
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
Water wash the vehicle and dry it with a clean cloth
Electrolyte ......................................................
Check level & top-up
Battery terminals .........................................
Clean and apply petroleum jelly
Drive chain free play .................................
Check, clean, lubricate & adjust
Rear brake pedal pivot ............................
Lubricate
Rear brake ....................................................
Cam clean, lubricate & Adjust play
Swing Arm Bush & Spacer ........................
Lubricate
Wheel rims front & rear .............................
Check spokes tightness
Front & Rear brake .....................................
Check & Adjust
Tyres front & rear ........................................
Check wear and tread depth
Air filter element ..........................................
Clean
Spark plugs (2 Nos) ....................................
Check, clean & adjust gap
H.T. Leads ......................................................
Inspect for cracks
Carburetor ....................................................
Clean, O/H & Tune
Fuel filter ........................................................
Clean
Fuel hose ........................................................
Inspect for cracks
Rubber hose, Air filter to carburetor .....
Inspect for cracks
Accelerator cable .......................................
Check & adjust play
Clutch cable ..................................................
Adjust play
Engine oil sump strainer ...........................
Clean
Engine oil .......................................................
Replace
Engine oil filter element .............................
Replace
Hand levers & kick starter pivot ..............
Lubricate
PAV System .....................................................
Check & Clean
Steering System ............................................
Check, Lub. steering balls & adj. play
90
CUSTOMER
COPY
Job Card No:
Date :
Odo Reading :
Name of Dealer/
ASP with Code:
..........................
..........................
ASP / Dealer’s
Stamp &
Signature
4TH FREE SERVICE
4TH
FREE
SERVICE
9000 KMS OR 270+15 DAYS WHICHEVER IS EARLIER FROM DATE OF SALE
Customer Name :
Dealer Code :
Address :
9000 Kms
or
270+15 days
whichever is
earlier from the
date of sale
Frame No:
Regn. No:
Engine No:
Sale Date:
Vehicle Installation Form No.
Serviced Date:
ODO Reading :
Serviced by
(Dealer’s/ASP Name & Address)
Enter the Details
in Free Service
Record
Sold by (Dealer’s Name & Address)
(Cost of oil,
oil filter element
and other
consumables
used are
chargeable to
the customer)
Received the above vehicle after the service having been done to my entire satisfaction.
Customer’s Signature : .................................
Contact Phone / Mobile No.:
91
Date :
4TH FREE SERVICE ACTIVITIES
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
Water wash the vehicle and dry it with a clean cloth
Electrolyte ......................................................
Check level & top-up
Battery terminals .........................................
Clean and apply petroleum jelly
Drive chain free play .................................
Check, clean, lubricate & adjust
Rear brake pedal pivot ............................
Lubricate
Rear brake ....................................................
Adjust
Wheel rims front & rear .............................
Check spokes tightness
Front & Rear brake .....................................
Check & Adjust
Front fork oil / leak .......................................
Check level & replace oil
Air filter element ..........................................
Clean
Spark plugs (2 Nos.) ...................................
Check, clean & adjust gap
H.T. Leads ......................................................
Inspect for cracks
Carburetor ....................................................
Drain & Tune
Fuel filter ........................................................
Clean
Fuel hose ........................................................
Inspect for cracks
Rubber hose, Air filter to carburetor .....
Inspect for cracks
Accelerator cable .......................................
Check & adjust play
Clutch cable ..................................................
Adjust play
Engine oil strainer .......................................
Clean
Engine oil .......................................................
Check level & top-up
Hand levers & kick starter pivot ..............
Lubricate
Steering free play / system .......................
Check and Lubricate Steering Balls & Adjust
Tyres ................................................................
Check wear and tread depth
92
CUSTOMER
COPY
Job Card No:
Date :
Odo Reading :
Name of Dealer/
ASP with Code:
..........................
..........................
ASP / Dealer’s
Stamp &
Signature
PAID SERVICE / MAINTENANCE RECORD
CUSTOMER COPY
DEALER / ASP COPY
12,000 + 250 Kms. Service
12,000 + 250 Kms. Service
Job Card No :.................Date : .........................
Job Card No :.................Date : .........................
Odo Reading : ................. Dealer Code : .............
Odo Reading : ................. Dealer Code : .............
Brief Work Done :
Brief Work Done :
Dealer’s Stamp & Signature
Dealer’s Stamp & Signature
CUSTOMER COPY
DEALER / ASP COPY
15,000 + 250 Kms. Service
15,000 + 250 Kms. Service
Job Card No :.................Date : .........................
Job Card No :.................Date : .........................
Odo Reading : ................. Dealer Code : .............
Odo Reading : ................. Dealer Code : .............
Brief Work Done :
Brief Work Done :
Dealer’s Stamp & Signature
Dealer’s Stamp & Signature
93
PAID SERVICE / MAINTENANCE RECORD
DEALER / ASP COPY
CUSTOMER COPY
12,000 + 250 Kms. Service
12,000 + 250 Kms. Service
Brief Work Done :
Brief Work Done :
Dealer’s Stamp & Signature
Dealer’s Stamp & Signature
DEALER / ASP COPY
CUSTOMER COPY
15,000 + 250 Kms. Service
15,000 + 250 Kms. Service
Brief Work Done :
Brief Work Done :
Dealer’s Stamp & Signature
Dealer’s Stamp & Signature
94
PAID SERVICE / MAINTENANCE RECORD
CUSTOMER COPY
DEALER / ASP COPY
18,000 + 250 Kms. Service
18,000 + 250 Kms. Service
Job Card No :.................Date : .........................
Job Card No :.................Date : .........................
Odo Reading : ................. Dealer Code : .............
Odo Reading : ................. Dealer Code : .............
Brief Work Done :
Brief Work Done :
Dealer’s Stamp & Signature
Dealer’s Stamp & Signature
CUSTOMER COPY
DEALER / ASP COPY
21,000 + 250 Kms. Service
21,000 + 250 Kms. Service
Job Card No :.................Date : .........................
Job Card No :.................Date : .........................
Odo Reading : ................. Dealer Code : .............
Odo Reading : ................. Dealer Code : .............
Brief Work Done :
Brief Work Done :
Dealer’s Stamp & Signature
Dealer’s Stamp & Signature
95
PAID SERVICE / MAINTENANCE RECORD
DEALER / ASP COPY
CUSTOMER COPY
18,000 + 250 Kms. Service
18,000 + 250 Kms. Service
Brief Work Done :
Brief Work Done :
Dealer’s Stamp & Signature
Dealer’s Stamp & Signature
DEALER / ASP COPY
CUSTOMER COPY
21,000 + 250 Kms. Service
21,000 + 250 Kms. Service
Brief Work Done :
Brief Work Done :
Dealer’s Stamp & Signature
Dealer’s Stamp & Signature
96
PAID SERVICE / MAINTENANCE RECORD
CUSTOMER COPY
DEALER / ASP COPY
24,000 + 250 Kms. Service
24,000 + 250 Kms. Service
Job Card No :.................Date : .........................
Job Card No :.................Date : .........................
Odo Reading : ................. Dealer Code : .............
Odo Reading : ................. Dealer Code : .............
Brief Work Done :
Brief Work Done :
Dealer’s Stamp & Signature
Dealer’s Stamp & Signature
CUSTOMER COPY
DEALER / ASP COPY
27,000 + 250 Kms. Service
27,000 + 250 Kms. Service
Job Card No :.................Date : .........................
Job Card No :.................Date : .........................
Odo Reading : ................. Dealer Code : .............
Odo Reading : ................. Dealer Code : .............
Brief Work Done :
Brief Work Done :
Dealer’s Stamp & Signature
Dealer’s Stamp & Signature
97
PAID SERVICE / MAINTENANCE RECORD
DEALER / ASP COPY
CUSTOMER COPY
24,000 + 250 Kms. Service
24,000 + 250 Kms. Service
Brief Work Done :
Brief Work Done :
Dealer’s Stamp & Signature
Dealer’s Stamp & Signature
DEALER / ASP COPY
CUSTOMER COPY
27,000 + 250 Kms. Service
27,000 + 250 Kms. Service
Brief Work Done :
Brief Work Done :
Dealer’s Stamp & Signature
Dealer’s Stamp & Signature
98
PAID SERVICE / MAINTENANCE RECORD
CUSTOMER COPY
DEALER / ASP COPY
30,000 + 250 Kms. Service
30,000 + 250 Kms. Service
Job Card No :.................Date : .........................
Job Card No :.................Date : .........................
Odo Reading : ................. Dealer Code : .............
Odo Reading : ................. Dealer Code : .............
Brief Work Done :
Brief Work Done :
Dealer’s Stamp & Signature
Dealer’s Stamp & Signature
CUSTOMER COPY
DEALER / ASP COPY
33,000 + 250 Kms. Service
33,000 + 250 Kms. Service
Job Card No :.................Date : .........................
Job Card No :.................Date : .........................
Odo Reading : ................. Dealer Code : .............
Odo Reading : ................. Dealer Code : .............
Brief Work Done :
Brief Work Done :
Dealer’s Stamp & Signature
Dealer’s Stamp & Signature
99
PAID SERVICE / MAINTENANCE RECORD
DEALER / ASP COPY
CUSTOMER COPY
30,000 + 250 Kms. Service
30,000 + 250 Kms. Service
Brief Work Done :
Brief Work Done :
Dealer’s Stamp & Signature
Dealer’s Stamp & Signature
DEALER / ASP COPY
CUSTOMER COPY
33,000 + 250 Kms. Service
33,000 + 250 Kms. Service
Brief Work Done :
Brief Work Done :
Dealer’s Stamp & Signature
Dealer’s Stamp & Signature
100
LOG BOOK
Sl.
No.
Date
Kms.
Idling
Co%
Details
101
Authorised Dealer / Service Point
Stamp &
Job Card No.
Signature
LOG BOOK
Sl.
No.
Date
Kms.
Idling
Co%
Details
102
Authorised Dealer / Service Point
Stamp &
Job Card No.
Signature
LOG BOOK
Sl.
No.
Date
Kms.
Idling
Co%
Details
103
Authorised Dealer / Service Point
Stamp &
Job Card No.
Signature
LOG BOOK
Sl.
No.
Date
Kms.
Idling
Co%
Details
104
Authorised Dealer / Service Point
Stamp &
Job Card No.
Signature
LOG BOOK
Sl.
No.
Date
Kms.
Idling
Co%
Details
105
Authorised Dealer / Service Point
Stamp &
Job Card No.
Signature
NOTES
106
NOTES
107
NOTES
108
Telephone Residence
Bike Regn. No.
Telephone Office
Invoice No.
E
Delivery Note / Advice No.
Sales Representative
or
Have you visited Royal Enfield website?
Yes
No
PRE DELIVERY INSPECTION LIST
MODEL: BULLET 350 / ELECTRA / CLASSIC 350 / CLASSIC 500 / BULLET 500
Model :
Engine No:
Dealer's Name :
Location:
Colour :
Key Number :
Battery Make :
Battery Number :
Aggregate
CHASSIS / ENGINE
NUMBER
Tyre Number :
Defect
Code
Area
1
CONNECT BATTERY /
2
CHECK VOLTAGE
Measure
Engine / Vehicle Number Details
DF
Same
Battery Charging
D / NC / Weak Battery Voltage 12V-whereas
13.5 V (Max. online voltage)
Cell
3
Fill 2.5 Litres (Capacity is
Replace oil & oil filter / Check Oil level (3 Drain
EO - (Drained 2.75 Litres) - Remove 3
Bolts system Hex 19mm, 8mm X 2nos and
Oil Level)
Drain Bolts to Drain the
Hex 12mm head bolts)
complete Oil
ENGINE OIL
4
Clean Primary Oil Strainer screen
-
Clean
LOCK OPERATION
5
Ignition / Side Air Filter Box / Tool Box Lock /
Fuel Tank Lock
H / LF / NW
Same
PETROL
6
Fill Petrol
-
5 Litres
7
Brake Lever Free Play
EP / T
2-3 mm / (STD)
8
Caliper Mounting Bolts
LF
2.7 to 3.0 Kgm
9
Front Wheel Rotation
W / T / LF / N
Free ( Check Spokes
Looseness & Runout
10
Front Mudguard Alignment / Cover Tube
Rubbing
M / RB
Straight
LF
7.0 to 7.7 Kgm
FRONT WHEEL
11 Front Wheel Nut
12 Front Tyre Condition (Check Tyre Line Seating) WF
Good
13 Front Tyre Pressure
LESS
22 PSI
14 Clutch Operation
H/N
Smooth
15 Clutch Lever Free Play
EP / V / T
2 - 3 mm
16 Accelerator Operation
T / SY
Smooth
17 Lever Brackets Tightness
LF
Tight
18 Switch Modules Tightness
LF
Tight
T
Free
WF
W.r.to Dot Punch
LF
4.5 to 5.5 Kgm
22 Electrical Switch Operation
NW / F
No Defects
23 Neutral Lamp
NW / F
No Defects
24 Fuel Tap Operation
H / NW
Smooth / Main / Reserve
25 Fuel Leak
L
No Leak ( Tank, Tap,
Carburetor)
26 Fuel Tank Alignment
M
Straight
27 Rear Brake Pedal Free Play
T / EP
20 - 30 mm
28 Pedal Position w.r.t foot rest
DF
Same Level
29 Chain Tension
T / EP
20 - 25 mm
30 Rear Wheel Rotation
W / T / LF / N
Free (Check Spokes
Looseness & Runout)
31 Anchor Pin Nut
LF
4.5 Kgm
32 Rear Mudguard Alignment
M
Straight
33 Rear Tyre Pressure
LESS
32 PSI
CLUTCH
HANDLE BAR
19 Steering Movement
CONTROLS &
ELECTRICAL SWITCH 20 Handle Bar Positioning
OPERATIONS
21 Lock Nut T- Stem
FUEL SYSTEM
REAR WHEEL
34 Rear Tyre Condition (Check Tyre Line Seating) WF
Good
35 RR Shock Absorber Operation / Adjustment
Smooth
H / N / AD
Front :
Defect Defect Defect
#1
#2
#3
Rear :
Remarks
36 Mudguards - Paint / Plating Related
SC / PD / R /
DN
No Defects (Mudguards /
Fuel Tank / Tool Box
37 Fuel Tank - Paint Related
SC / PD / R /
DN
No Defects
38 Tool Box LH, Air Filter Box, Battery Cover Paint / Plating Related
SC / PD / R /
DN
No Defects
39 Head Lamp Casing - Paint Related
SC / PD / R /
No Defects
SC / PD / R
No Defects
41 Plated Parts (Scratch / Rusty)
SC / R / PO
No Defects (Mudguards /
Fuel Tank / Wheel Rim /
Indicator
42 Buffed components poor Buffing & Scratches
SC / DU
No Defects
43 Seat Alignment
M
No Defects
44 Indicators Alignment (MFR / Amber)
M
No Defect / Colour
45 Stickers / Knee Pads
M / LF / SC
No Defects
46 Nuts, Bolts, Fasteners (Torque)
LF
Tight (RH, LH Cover /
Engine Foundation /
Accessories / Wheel Nut)
47 Owner's Manual & Tool Kit Content
-
Availability
48 Spare Fuse in Fuse Carrier
NA
Tubular / Blade Fuse
49 Starting (Kick Start / Self Start)
ST / N
Easy Start
50 Front / Rear Brakes Effectiveness / Feel
AD / SG
Sharp
51 Pulling
P
Straight
52 Vibration
V
Smooth
53 Wobbling
W
No Defects
54 Front Fork / Drive Chain Noise
N
No Defects
55 Engine Performance / Gear Shifting /
TPS Setting
N / ST / J / H
Smooth
56 Any Rattling / Squeaking Noise
N
Nil (Silencer / Accessories
/ Body Parts /
Suspension)
57 Easy Start (Hot Condition)
ST / NW
Smooth
58 Leak
L
No Leak (Oil / Fuel /
Hydraulic / Acid Leakage)
59 Smoke / Oil Droplets in Silencer
SK / EO
No Smoke
60 Cam Noise / Top End Noise
N
Smooth
40
AESTHETICS
Powder Coated Parts (Scratch / Rust /
Chipped OFF)
OTHERS
TEST RIDE
STATIC CHECK
(AFTER TEST RIDE)
Lens Colour Check
ANY OTHER
Any Abnormal Noise or Engine Open cases during PDI Inform to Plant / Factory
Note **
INSTRUCTIONS
1. Check the vehicle thoroughly for any transit damages or
shortage of parts.
4. Please ensure delivery of the vehicle in brand new condition.
2. Carry out all jobs listed under Pre-delivery Inspection Schedule.
6. Claim Parts replaced for Manufacturing defects only under
warranty.
5. Claim transit loss and damage through ‘TRANSIT’ insurance only.
3. Thoroughly road - test the vehicle for performance.
Misalignment
Noise
Vibration
Leak
Starting
Trouble/Missing
Less
Wobbling
Loose
Fitment
Discharing
Tight
Fused
Scratch
Pulling
Dent
Wrong
Fitment
Hard
Jerking
M
N
V
L
ST
LESS
W
LF
D
T
F
SC
P
DN
WF
H
J
Excess Play
Different
Spongy
Sticky
Not
Available
Smoke
Adjustment
Not
Working
Paint Defect
Rust
Peel Off
Dull
Excessive Oil
Rubbing
Not Charging
EP
DF
SG
SY
NA
SK
AD
NW
PD
R
PO
DU
EO
RB
Format No : F/14A/CS/02, Mar. 2013
NC
DLR / CS COPY
BIKE INSTALLATION CONFIRMATION BY CUSTOMER
We congratulate you on becoming a proud owner of Royal Enfield bike. We request
you to give this feedback after completion of the delivery process.
YES
1
2
3
4
5
6
7
8
9
10
11
12
Bike Documents explained (Invoice, Insurance, RC / Road Tax Receipt)
Owner’s Manual received
Recommended Lubricants explained
Maintenance Schedule sheet in Owner’s Manual shown and explained
Next Free Service due explained
All Free / Paid Services explained
Warranty Guidelines explained
“Running in period” details shown in the manual explained
Service Station Address given and Location explained
Service Incharge Name & Mobile No given
Bike delivered in neat and clean condition
Tool Kit & First Aid Kit received and explained
NO
YES
13
14
15
16
17
18
19
20
NO
Control Switches & Disc Brake System usage explained
Fuse Box location shown and explained
Recommended Tyre Pressure explained
Bike starting & Gear shifting procedure explained
Quantity of Fuel in Fuel Tank informed
Bike orientation & short distance drive provided
Date and Time of Installation
Name of Person who did Installation
Suggestions If Any:
CUSTOMER
SIGNATURE
Model:
Registration No.:
Chassis No.:
We thank you and request you to return this filled up form to the person who
did the bike installation for you
KEEP RIDINGP
FORM 22
[See Rules 47(g), 115, 124 (2), 126A and 127 (1), 127 (2)]
INITIAL CERTIFICATE OF COMPLIANCE WITH POLLUTION STANDARDS, SAFETY
STANDARDS OF COMPONENTS AND ROAD WORTHINESS
Certified that the following vehicle complies with the provisions of the Motor Vehicles Act, 1988, and the
rules made there under, including the following mass emission norms:
Bullet 500
Brand name of the vehicle
:-
Chassis number
:-
Engine number/motor number
(in case of battery operated vehicles)
:-
Sub-rule No. of rule
:-
115(2)(i), 115(14)(F)
Emission norms
[Bharat Stage-I/II/III/Bharat (Trem) Stage-III etc.]
:-
Bharat Stage III
Date :
For ROYAL ENFIELD
Quality Assurance