Bosch UMS-20 Series Installation manual

UMS Series Public View Monitor
UMS-20xxxA and UMS-20xxxC
en
Installation Manual
en
Important Safeguards
1. Read, Follow, and Retain Instructions - All safety and operating instructions should be read and followed before operating the unit. Retain instructions for future reference.
2. Heed Warnings - Adhere to all warnings on the unit and in
the operating instructions.
3. Attachments - Attachments not recommended by the product manufacturer should not be used, as they may cause
hazards.
4. Installation Cautions - Do not place this unit on an unstable
stand, tripod, bracket, or mount. The unit may fall, causing
serious injury to a person and serious damage to the unit.
Use only manufacturer-recommended accessories, or those
sold with the product. Mount the unit per the manufacturer's instructions. Appliance and cart combination should
be moved with care. Quick stops, excessive force, or
uneven surfaces may cause the appliance and cart combination to overturn.
5. Cleaning - Unplug the unit from the outlet before cleaning.
Follow any instructions provided with the unit. Generally,
using a damp cloth for cleaning is sufficient. Do not use liquid cleaners or aerosol cleaners.
6. Servicing - Do not attempt to service this unit yourself.
Opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified service personnel.
7. Damage Requiring Service - Unplug the unit from the main
AC power source and refer servicing to qualified service
personnel under the following conditions:
•
•
When the power supply cord or plug is damaged.
If liquid has been spilled or an object has fallen into the
unit.
• If the unit has been exposed to water and/or inclement
weather (rain, snow, etc.).
• If the unit does not operate normally, when following
the operating instructions. Adjust only those controls
specified in the operating instructions. Improper adjustment of other controls may result in damage, and
require extensive work by a qualified technician to
restore the unit to normal operation.
• If the unit has been dropped or the cabinet damaged.
• If the unit exhibits a distinct change in performance, this
indicates that service is needed.
8. Replacement Parts - When replacement parts are required,
the service technician should use replacement parts specified by the manufacturer or that have the same characteristics as the original part. Unauthorized substitutions may
result in fire, electrical shock or other hazards.
9. Safety Check - Upon completion of servicing or repairs to
the unit, ask the service technician to perform safety
checks to ensure proper operating condition.
F01U029703 | 1.0 | 2006.07
iii
10.Power Sources - Operate the unit only from the type of
power source indicated on the label. If unsure of the type of
power supply to use, contact your dealer or local power
company.
•
For units intended to operate from battery power, refer
to the operating instructions.
• For units intended to operate with External Power Supplies, use only the recommended approved power supplies.
• For units intended to operate with a limited power
source, this power source must comply with EN60950.
Substitutions may damage the unit or cause fire or
shock.
• For units intended to operate at 24VAC, normal input
voltage is 24VAC. Voltage applied to the unit's power
input should not exceed 30VAC.
User-supplied wiring, from the 24VAC supply to unit, must
be in compliance with electrical codes (Class 2 power levels). Do not ground the 24VAC supply at the terminals or at
the unit's power supply terminals.
11.Coax Grounding - If an outside cable system is connected
to the unit, ensure that the cable system is grounded.
U.S.A. models only - Section 810 of the National Electrical
Code, ANSI/NFPA No.70, provides information regarding
proper grounding of the mount and supporting structure,
grounding of the coax to a discharge unit, size of grounding
conductors, location of discharge unit, connection to
grounding electrodes, and requirements for the grounding
electrode.
12.Grounding - This unit may be equipped with a 3-wire
grounding plug (a plug with a third pin, for grounding). This
safety feature allows the plug to fit into a grounding power
outlet only. If unable to insert the plug into the outlet, contact an electrician to arrange replacement of the obsolete
outlet. Do not defeat the safety purpose of the grounding
plug.
•
•
•
Outdoor equipment should only be connected to the
unit's inputs after this unit has had its grounding plug
connected to a grounded outlet or its ground terminal
properly connected to a ground source.
The unit's input connectors must be disconnected from
outdoor equipment before disconnecting the grounding
plug or grounding terminal.
Proper safety precautions such as grounding should be
followed for any outdoor device connected to this unit.
13.Lightning - For added protection during a lightning storm,
or when this unit is left unattended and unused for long
periods of time, unplug the unit from the wall outlet and
disconnect the cable system. This will prevent damage to
the unit due to lightning and power line surges.
Bosch Security Systems, Inc.
iv
en
For Indoor Product
WARNING:
1. Water and Moisture - Do not use this unit near water for example, in a wet basement, in an unprotected outdoor installation or in any area classified as a wet location.
Electrostatic-sensitive device. Use proper CMOS/
MOSFET handling precautions to avoid electrostatic discharge.
2. Object and Liquid Entry - Never push objects of any
kind into this unit through openings, as they might touch
dangerous voltage points or create short circuits, resulting in a fire or electrical shock. Never spill liquid of any
kind on the unit.
3. Power Cord and Power Cord Protection - For units
intended to operate with 230VAC, 50Hz, the input and
output power cord must comply with the latest versions
of IEC Publication 227 or IEC Publication 245. Power
supply cords should be routed so they are not likely to
be walked on or pinched. Pay particular attention to
location of cords and plugs, convenience receptacles,
and the point of exit from the appliance.
4. Overloading - Do not overload outlets and extension
cords; this can result in a risk of fire or electrical shock.
For Outdoor Product
Power Lines - An outdoor system should not be located
in the vicinity of overhead power lines, electric lights or
power circuits, or where it may contact such power lines
or circuits. When installing an outdoor system, extreme
care should be taken to keep from touching power lines
or circuits, as this contact might be fatal. U.S.A. models
only - refer to the National Electrical Code Article 820
regarding installation of CATV systems.
For Rack-mount Product
1. Ventilation - Do not place this equipment in a built-in
installation or rack, unless proper ventilation is provided, or the manufacturer's instructions were followed.
The equipment must not exceed its maximum operating
temperature requirements.
NOTE: Grounded wrist straps must be worn and
proper ESD safety precautions observed when
handling the electrostatic-sensitive printed circuit
boards.
This symbol indicates the presence of important
operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Cover Removal
Warning: Removal of the cover should only be
performed by qualified service personnel - not
user serviceable. The unit should always be
unplugged before removing the cover and remain
unplugged while the cover is removed.
24 VAC Units
Do not exceed 30VAC input. Voltage applied to the unit's
power input should not exceed 30VAC. Normal input voltage is
24VAC. User supplied wiring from 24VAC supply to unit must
be in compliance with electrical codes (Class 2 power levels).
Do not ground 24VAC supply at power supply terminals or at
unit's power supply terminals.
This equipment is to be isolated from the mains
supply by a limited power source as specified in
EN60950.
220-240V, 50Hz Power Cords
220-240V, 50Hz power cords, input and output, must comply
with the latest versions of IEC Publication 227 or IEC Publication 245.
2. Mechanical Loading - When rack-mounting the equipment, ensure that a hazardous condition is not created
by uneven mechanical loading.
Bosch Security Systems, Inc.
F01U029703 | 1.0 | 2006.07
en
FCC & ICES INFORMATION
v
Safety Precautions
(U.S.A. and Canadian Models Only)
This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions:
(1)This device may not cause harmful interference, and
(2)This device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to Part 15
of the FCC Rules and ICES-003 of Industry Canada. These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses and
radiates radio frequency energy, and if not installed and used
in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the
interference at his expense.
Intentional or unintentional changes or modifications, not
expressly approved by the party responsible for compliance,
shall not be made. Any such changes or modifications could
void the user’s authority to operate the equipment. If necessary, the user should consult the dealer or an experienced
radio/television technician for corrective action. The user may
find the following booklet, prepared by the Federal Communications Commission, helpful: How to Identify and Resolve RadioTV Interference Problems. This booklet is available from the U.S.
Government Printing Office, Washington, DC 20402, Stock No.
004-000-00345-4.
WARNING: This is a Class A product. In a domestic environment, this product may cause radio interference, in which
case, the user may be required to take adequate measures.
F01U029703 | 1.0 | 2006.07
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
This symbol indicates the presence of uninsulated
“dangerous voltage” within the product’s enclosure that can cause an electric shock.
This symbol indicates the presence of important
operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Installation should be performed by qualified service personnel only in accordance with the
National Electrical Code or applicable local codes.
Power Disconnect. Units with or without ON-OFF
switches have power supplied to the unit whenever the power cord is inserted into the power
source; however, the unit is operational only when
the ON-OFF switch is in the ON position. The
power cord is the main power disconnect for all
units.
Bosch Security Systems, Inc.
vi
en
INFORMATIONS FCC ET ICES
Sécurité
(modèles utilisés aux États-Unis et au Canada uniquement)
Attention : l'installation doit exclusivement être réalisée par du
Ce produit est conforme aux normes FCC partie 15. la mise en
service est soumises aux deux conditions suivantes:
(1) cet appareil ne peut pas provoquer d'interférence nuisible
et
(2) cet appareil doit pouvoir tolérer toutes les interférences
auxquelles il est soumit, y compris les interférences qui
pourraient influer sur son bon fonctionnement.
AVERTISSEMENT: Suite à différents tests, cet appareil s’est
révélé conforme aux exigences imposées aux appareils
numériques de Classe A en vertu de la section 15 du règlement
de la Commission fédérale des communications des États-Unis
(FCC). Ces contraintes sont destinées à fournir une protection
raisonnable contre les interférences nuisibles quand l'appareil
est utilisé dans une installation commerciale. Cette appareil
génère, utilise et émet de l'energie de fréquence radio, et peut,
en cas d'installation ou d'utilisation non conforme aux instructions, générer des interférences nuisibles aux communications
radio. L’utilisation de ce produit dans une zone résidentielle
peut provoquer des interférences nuisibles. Le cas échéant,
l’utilisateur devra remédier à ces interférences à ses propres
frais.
Au besoin, l’utilisateur consultera son revendeur ou un technicien qualifié en radio/télévision, qui procédera à une opération corrective. La brochure suivante, publiée par la
Commission fédérale des communications (FCC), peut
s’avérer utile : « How to Identify and Resolve Radio-TV Interference Problems » (Comment identifier et résoudre les
problèmes d’interférences de radio et de télévision). Cette
brochure est disponible auprès du U.S. Government Printing
Office, Washington, DC 20402, États-Unis, sous la référence n°
004-000-00345-4.
Avertissement : Ce produit est un appareil de Classe A. Son
utilisation dans une zone résidentielle risque de provoquer
des interférences. Le cas échéant, l’utilisateur devra prendre
les mesures nécessaires pour y remédier.
Bosch Security Systems, Inc.
ATTENTION : POUR ÉVITER TOUT RISQUE D'ÉLECTROCUTION, N'ESSAYEZ PAS DE RETIRER LE CAPOT (OU LE PANNEAU ARRIÈRE). CET APPAREIL NE CONTIENT AUCUN
COMPOSANT SUSCEPTIBLE D'ÊTRE RÉPARÉ PAR L'UTILISATEUR. CONFIEZ LA RÉPARATION DE L'APPAREIL À DU
PERSONNEL QUALIFIÉ.
Ce symbole signale que le produit renferme une «
tension potentiellement dangereuse » non isolée
susceptible de provoquer une électrocution.
Ce symbole invite l'utilisateur à consulter les
instructions d'utilisation et d'entretien (dépannage) reprises dans la documentation qui
accompagne l'appareil.
Attention: l'installation doit exclusivement être
réalisée par du personnel qualifié, conformément
au code national d'électricité américain (NEC) ou
au code d'électricité local en vigueur.
Coupure de l'alimentation. Qu'ils soient pourvus
ou non d'un commutateur ON/OFF, tous les appareils reçoivent de l'énergie une fois le cordon
branché sur la source d'alimentation. Toutefois,
l'appareil ne fonctionne réellement que lorsque le
commutateur est réglé sur ON. Le débranchement
du cordon d'alimentation permet de couper l'alimentation des appareils.
F01U029703 | 1.0 | 2006.07
en vii
AVERTISSEMENT:
cet appareil est sensible aux décharges électrostatiques. Pour éviter tout risque de décharge électrostatique, observez les précautions de
manipulation du CMOS/MOSFET appropriées.
REMARQUE : lors de la manipulation des cartes à
circuits imprimés sensibles aux décharges électrostatiques, portez des bracelets antistatiques
mis à la terre et observez les consignes de sécurité relatives aux décharges électrostatiques.
ATTENTION : pile au lithium
Le remplacement incorrect de la pile risque de
provoquer une explosion. Remplacez la pile exclusivement par une pile identique ou par un type de
pile équivalent recommandé par le fabricant.
Débarrassez-vous de la pile usagée conformément
aux instructions de son fabricant.
Enlèvement du capot
Avertissement : L’enlèvement du capot ne doit
être effectué que par un technicien spécialisé. Il
n’y a pas de pièces remplaçables ou réglables par
l’utilisateur. Il faut toujours débrancher l’appareil
avant d’enlever le capot et le laisser débranché
jusqu’à la remise en place du capot.
24 VAC Units
Ne pas excéder 30 V c.a. La tension appliquée à l’entrée d’alimentation de l’appareil ne doit pas excéder 30 V c.a. La valeur
normale de la tension d’entrée est 24 V c.a. Le circuit électrique reliant l’alimentation 24 V c.a. à l’appareil doit être conforme aux codes électriques (niveaux d’alimentation de classe
2). Ne pas mettre l’alimentation 24 V c.a. à la masse au niveau
des bornes de l’alimentation ou de l’appareil.
Cet équipement doit être isolé de l’alimentation
secteur par une source de puissance limitée, conformément à la norme EN60950.
Cordons d’alimentation 220-240 V, 50 Hz
Les cordons d’alimentation 220-240 V, 50 Hz, d’entrée ou de
sortie, doivent être conformes à la dernière version de la publication IEC 227 ou IEC 245.
F01U029703 | 1.0 | 2006.07
Bosch Security Systems, Inc.
viii en
Bosch Security Systems, Inc.
F01U029703 | 1.0 | 2006.07
UMS Series Public View Monitor
| en
ix
Preface
This guide describes how to install and configure the UMS Series Public View Monitor.
Audience
This guide is intended for qualified installation and service personnel who are familiar with the applicable national
and local electrical codes.
Document Conventions
Convention
Bold
Bold Italic
Underline
Meaning
Denotes a part, item, or assembly.
Denotes a reference to another paragraph, figure or table.
Used to emphasize a point.
Customer Support and Service
If this unit needs service, contact the nearest Bosch Security Systems Service Center for authorization to return and
shipping instructions.
Service Centers
USA
Phone: 800-366-2283 or 585-340-4162
Fax: 800-366-1329
Email: cctv.repair@us.bosch.com
CCTV Spare Parts
Phone: 800-894-5215 or 408-957-3065
Fax: 408-935-5938
Email: BoschCCTVparts@ca.slr.com
Canada
Phone: 514-738-2434
Fax: 514-738-8480
Europe, Middle East & Asia Pacific Region
Phone: 44 (0) 1495 274558
Fax: 44 (0) 1495 274280
Email: rmahelpdesk@solectron.com
For additional information, see www.boschsecurity.com
Related Publications
Refer to the latest Bosch Security Systems Databook for the most up-to-date datasheets. To obtain a copy of the
Databook, please contact your local Bosch representative.
You can also visit the Bosch Security Systems World Wide Web site at:
http://www.boschsecurity.com to view a current listings of our publications.
Bosch Security Systems, Inc.
Installation Manual
F01U029703 | 1.0 | 2006.07
x
en |
F01U029703 | 1.0 | 2006.07
UMS Series
Installation Manual
Bosch Security Systems, Inc.
UMS Series Public View Monitor
Table of Contents | en
xi
Table of Contents
1
Unpacking
1
1.1
Parts List
1
2
Description
2
2.1
General Features
2
2.2
UMS Series Models
2
3
Installing the UMS Series
3
3.1
Power
3
3.2
Mounting
3
3.3
Power Connection
4
3.4
Video Connections
4
3.5
Remote Control Battery Installation
5
4
Monitor Remote Control Functions (Bosch)
6
4.1
Monitor Remote Control Operating Modes
7
4.2
Navigating the Monitor On-screen Display (OSD)
7
4.3
Monitor Remote Control On-screen Display Menus
7
4.4
Input Select Menu
9
5
Using the Card Reader
10
5.1
Compatible Flash Memory Cards
10
5.2
Image Requirements
10
6
Card Reader Remote Control Functions (SanDisk®)
12
6.1
Card Reader On-screen Display Menu Selections
12
6.2
Card Reader Menu Selections
13
7
Configuring Motion Detection
16
7.1
Selecting a Mounting Location
16
7.2
Activating the PIR
16
8
Camera Tilt and Pivot Adjustments
17
8.1
High-resolution Color Series Camera
17
8.2
Dip Switch Location for the High-resolution Color Camera
18
8.3
Wide Dynamic Range (WDR) Series Camera
19
8.4
Dip Switch Location for Wide Dynamic Range (WDR) Camera
19
8.5
Focusing the Camera
20
8.6
Light Sensor
20
Bosch Security Systems, Inc.
Installation Manual
F01U029703 | 1.0 | 2006.07
xii
9
en | Table of Contents
UMS Series Public View Monitor
Troubleshooting
21
9.1
Make adjustments to the control board and option switches
21
9.2
Screen flickers
22
9.3
No video displayed
23
9.4
Only displays Power Save mode
23
9.5
Remote control does not activate the monitor
24
9.6
Lost remote control
24
9.7
Memory card images appear stretched and out of proportion
25
9.8
Images are smaller than the recommended size
25
9.9
Question marks are displayed in the preview mode
25
9.10
Movie clips do not play
25
9.11
Card reader does not display images
25
9.12
Monitor does not display AUTO or AUX video when turned on
26
10
UMS Ordering Information
27
10.1
Power Supply
27
10.2
Mounting Options
27
10.3
Replacement Parts
27
11
Specifications
28
F01U029703 | 1.0 | 2006.07
Installation Manual
Bosch Security Systems, Inc.
UMS Series Public View System
1
Unpacking | en
1
Unpacking
This equipment should be unpacked and handled with care. If an item appears to have been
damaged in shipment, notify the shipper. Verify that all parts shown in the Parts List are
included. If any items are missing, notify your Bosch Security Systems Sales or Customer Service Representative.
The original packing carton is the safest container in which to transport the unit. Save it for
possible future use.
1.1
Parts List
The following table lists the components that comes with all UMS Series systems:
Qty
Item
1
UMS LCD monitor
1
Monitor remote control (Bosch) with two (2) AAA batteries
2
Wago® clamps, used to connect the power leads from the UMS Public View Monitor
and the leads from the power supply.
1
This installation manual
The following additional equipment comes with the UMS-20xxxC Series models:
1
Memory card reader (SanDisk) remote control with two (2) AAA batteries
(UMS-20xxxC models only)
i
NOTICE! It is recommended that you do not remove the clear protective plastic covers on the
UMS at this time.
Bosch Security Systems, Inc.
Installation Manual
F01U029703 | 1.0 | 2006.07
2
2
en | Description
UMS Series Public View System
Description
The Universal Monitor System (UMS) Series provides video surveillance and advertising display in one system. It contains an LCD display, a hidden CCTV camera, a built-in memory card
reader*, and motion and light sensors.
The UMS 20xxxC Series, with an optional integrated memory card reader, displays images
from a Flash memory card reader.
The motion sensor allows the UMS Series to switch from displaying logos or advertising to displaying a message that alerts viewers to the use of surveillance equipment. The light sensor
detects low light levels, which triggers the UMS Series to power down the monitor while the
camera continues to film.
The UMS Series also features feed-through wiring and a button-less housing, to minimize
unauthorized tampering, and a remote control to control the optional card reader. See
Section 4, Monitor Remote Control Functions (Bosch), on page 6 for more information.
2.1
General Features
The UMS Series features a 20.1-inch LCD flat-panel monitor with either a high resolution color
camera (3–6 mm lens) or a wide dynamic range camera (3.8–9.5 mm lens). The UMS Series is
equipped with a varifocal, auto iris lens, has 640 x 480 pixels resolution, includes four (4)
memory card reader slots, features advanced power management, and supports plug and play
technology.
2.2
UMS Series Models
Each UMS Series Public View system offers some or all of the following features:
–
20.1-inch LCD flat-panel monitor
–
High resolution color and wide dynamic range camera options
–
Integrated memory card reader for storing welcome messages, logos, or advertising
–
Built-in motion sensor switches monitor from advertising to surveillance mode
–
Light sensor that triggers the Monitor Sleep mode
–
IR remote control and on-screen display for easy setup and control
–
All cables are concealed
The following table lists a summary of features for each UMS model:
Model Number
Features
UMS-20S36A-B20 20.1 inch LCD monitor with a high-resolution, color camera, 3–6 mm lens,
24 VAC, 60 Hz, motion sensor, light sensor, black cabinet
UMS-20S36C-B20 20.1 inch LCD monitor with a high-resolution, color camera and a memory
card reader, 3–6 mm lens, 24 VAC, 60 Hz, motion sensor, light sensor,
black cabinet
UMS-20W39A-B20 20.1 inch LCD monitor with a high-resolution, wide dynamic color camera,
3.8–9.5 mm lens, 24 VAC, 60 Hz, motion sensor, light sensor, black cabinet
UMS-20W39C-B20 20.1 inch LCD monitor with a high-resolution, wide dynamic color camera
and a memory card reader, 3.8–9.5 mm lens, 24 VAC, 60 Hz, motion sensor, light sensor, black cabinet
* Only available with UMS-20S36C-xxx and UMS-20W39C-xxx.
F01U029703 | 1.0 | 2006.07
Installation Manual
Bosch Security Systems, Inc.
UMS Series Public View System
3
Installing the UMS Series | en
3
Installing the UMS Series
This section provides instructions for installing and configuring the UMS Series.
!
3.1
3.2
CAUTION! Installation should be performed by qualified service installers only, using
construction methods in accordance with applicable local codes and standards.
Power
Model
Rated Voltage
Voltage Range
Power at Rated Voltage Sync. Format
UMS
24 VAC, 60 Hz
22-26 VAC
80 W/100 VA
NTSC
Mounting
The UMS Series has both 2.95-in. (75-mm) and 3.94-in. (100-mm) mounting hole patterns. The
holes are threaded for #10-24 screws with a maximum length of 3/8 in. (not provided with the
UMS Series). In addition, the UMS Series features two mounting holes in which you can attach
a sign to the UMS Series housing. The following illustration details the mounting hole patterns
on the back of the UMS monitor:
17.88
8.94
1.97
1.48
3.94
TYP
2.95
TYP
6.96
2
1
8.13
8.97
3
3
4
4
8.28
Fig. 3.1 UMS Series Mounting Hole Pattern
Bosch Security Systems, Inc.
Installation Manual
F01U029703 | 1.0 | 2006.07
4
en | Installing the UMS Series
UMS Series Public View System
Ref. # Description
1
2.95-in. (75-mm) mounting hole pattern
2
3.94-in. (100-mm) mounting hole pattern
3
Thumbscrews
4
Sign mounting hole pattern
(To mount a sign, use #8-32 screws with a maximum length of 5/16 in.)
To mount the UMS Series you must use the following hardware:
Quantity
Description
4
#10-24 3/8 BHC stainless steel patch lock screws*
4
#10 plain type stainless steel flat washers*
* The screws and washers are not provided with the UMS Series.
The UMS Series is available in a variety of mount configurations. For specific directions on
mounting the unit, see the manual that came with your mount. Once the UMS is mounted,
remove the clear protective plastic covers and continue the installation procedure.
3.3
Power Connection
Attach the two (2) 24 VAC power leads to your transformer/power supply. It is recommended
to use the UMP-24V4P0-60 power supply, otherwise see Section 3.1, Power, on page 3 for the
acceptable voltage range. Once power is supplied, the unit automatically turns on.
3.4
Video Connections
Each UMS Series model offers either a Video In or a Video Out connector.
3.4.1
Video In (UMS-20xxxA models only)
If you have an external video source you would like to use as the auxiliary source, connect the
cable to the Video In connector.
3.4.2
Video Out (both models)
To connect the camera to a monitoring station, attach a coax cable to the Video Out connector on the unit to the input connector of the external monitor/recorder.
i
NOTICE! UMS models that feature an internal card reader do not include a Video In
connector.
F01U029703 | 1.0 | 2006.07
Installation Manual
Bosch Security Systems, Inc.
UMS Series Public View System
3.5
Installing the UMS Series | en
5
Remote Control Battery Installation
1.
Turn the remote over (buttons facing down) and push down on the cover and slide it off.
2.
Insert two (2) new AAA alkaline batteries, matching the batteries to the (+) and (-) marks
inside the battery case.
Fig. 3.2 Battery Installation
3.
i
Slide the battery cover back into place.
NOTICE! Replace batteries when required or at least once a year. Dispose of used batteries
properly.
Bosch Security Systems, Inc.
Installation Manual
F01U029703 | 1.0 | 2006.07
6
4
en | Monitor Remote Control Functions (Bosch)
UMS Series Public View System
Monitor Remote Control Functions (Bosch)
This section details the functions and the usage of the Bosch remote control.
Button
Function
AUTO
Switches between images from the
auxiliary video to the surveillance video
when motion is detected. The auxiliary
video source for each mode is:
UMS-20xxxA: Video In
UMS-20xxxB: Memory card reader
MEM
Saves current operating mode during
Sleep mode or power failures. Does
not save operating mode when the unit
is turned off with this remote control.
MON
Activates the On-screen Display (OSD)
menu for the LCD panel.
CAM
Displays ONLY video from the internal
CCTV camera (disables switching from
CCTV video to auxiliary video).
Moves the cursor up in an OSD menu.
AUX
Displays ONLY a JPG image or video
from an external source, depending on
the model number (disables switching
from auxiliary video to the internal
CCTV camera).

MENU
Moves the cursor left or decreases
item values in an OSD menu.
Displays the OSD. Pressing the MENU
button returns you to the Main menu
from anywhere in the OSD menus.
Moves the cursor right or increases
item values in an OSD menu.
RST
Reserved for future use.
Moves the cursor down in an OSD
menu.
CLR
Clears any keystrokes.
ON
Returns the display from CAM mode
only to Standby mode. Press the AUTO
or AUX to select these modes if preferred.
OFF
Turns the display to Standby mode,
but the internal camera remains on.
F01U029703 | 1.0 | 2006.07
Installation Manual
Bosch Security Systems, Inc.
UMS Series Public View System
4.1
Monitor Remote Control Functions (Bosch) | en
7
Monitor Remote Control Operating Modes
There are three (3) operating modes for the UMS Series:
–
AUTO: The UMS switches between images from an auxiliary (external) video source to surveillance video when motion is detected.
–
AUX: The UMS displays only images stored on a memory card or from the external video
source.
–
4.2
CAM: The UMS monitor displays only surveillance (internal camera) video.
Navigating the Monitor On-screen Display (OSD)
Use the Bosch remote control to make any necessary adjustments to the UMS. To navigate the
set up menus, follow the steps below:
1.
Power on the unit by aiming the Bosch remote control at the bottom portion of UMS and
press the ON button.
2.
4.3
Press the MENU button to activate the Main menu selections:
–
Video
–
OSD (On-screen Display)
–
Misc.
–
Input Select
3.
Press the
and
4.
Press the
and
5.
Press the
 and
6.
When finished, press the MENU button to accept any changes.
buttons to select a main menu.
buttons to navigate through the sub-menus.
buttons to select and edit any of the sub-menus.
Monitor Remote Control On-screen Display Menus
There are five (5) on-screen main menus which allow you to customize your settings.
Icon
Menu
Function
Video
Adjusts the LCD monitor settings.
OSD
Adjusts the position of the OSD.
Misc.
Displays information and allows you to reset setting to their
factory preset values.
Audio
Not applicable
Input Select
Selects the video source. Do not change this setting.
Table 4.1 On-screen Menus
Bosch Security Systems, Inc.
Installation Manual
F01U029703 | 1.0 | 2006.07
8
en | Monitor Remote Control Functions (Bosch)
4.3.1
UMS Series Public View System
Video Menu
The Video menu allows you to customize the screen by adjusting the Sharpness, Brightness,
Backlight, Contrast, Color, and Tint from a range of 0-100 .
Fig. 4.1
Video Menu Example
Submenu
Default Setting
Definition
Sharpness
0
Adjusts the clarity
Brightness
50
Adjusts the background black level
Backlight
75
Adjusts the luminance level
Contrast
50
Adjusts the foreground white level
Color
50
Adjusts the saturation
Tint
50
Adjusts the RGB colors
Table 4.2
4.3.2
Video Submenu Default Settings
OSD Menu
The OSD menu allows you to customize the screen by adjusting the Horizontal Position, Vertical Position, and Blending from a range of 0-100. The OSD menu also allows you to set the
duration of time (0-60 seconds) that the unit displays the OSD and gives you the option to
switch Languages.
Fig. 4.2
OSD Menu Example
Submenu
Default Setting
Definition
Horizontal position 50
Adjusts horizontal position of the OSD menu
Vertical position
50
Adjusts vertical position of the OSD menu
Blending
0
Adjusts transparency of the OSD menu
Duration
5 sec.
Adjusts the menu time out (0-60 sec)
Language
English
Selects OSD language (English, Spanish, French,
Dutch, and Italian)
Table 4.3
F01U029703 | 1.0 | 2006.07
Submenu Default Settings
Installation Manual
Bosch Security Systems, Inc.
UMS Series Public View System
4.3.3
Monitor Remote Control Functions (Bosch) | en
9
Misc. Menu
The Misc. menu allows you to verify information about the unit, reset the settings to the factory default, and edit the display and OSD.
Fig. 4.3 Misc. Menu Example
i
4.4
Submenu
Default Setting
Definition
Information
None
Displays panel information
Factory Preset
None
Resets all settings to the factory default
Mirroring
OFF
Selects a mirror image
Upside Down
OFF
Rotates 180 degrees
Display Aspect
None
N/A
NOTICE! The Display Aspect feature is not applicable to this unit.
Input Select Menu
The Input Select menu is not applicable to the UMS Series. Video should always be
selected. All other input selections causes the UMS to enter the Power Save mode.
In this case, do the following:
1.
Press the Power On button on the Bosch remote control.
2.
When the monitor displays the message DPMS Power Save Mode, press MENU again.
The monitor displays the Input Select screen and the Video option should be ON.
3.
If Video is not ON, use the
or
buttons to select Video, then press the
button to
automatically display video on the monitor.
Fig. 4.4 Input Select Menu
Sub menu
Default Setting
Video
ON
Bosch Security Systems, Inc.
Installation Manual
F01U029703 | 1.0 | 2006.07
10
en | Using the Card Reader
5
UMS Series Public View System
Using the Card Reader
UMS-20xxxC models contain a card reader that allows you to expand the number of JPEG
images displayed on the UMS monitor.
5.1
Compatible Flash Memory Cards
A flash memory card is a compact, portable recording medium with a data capacity that
exceeds the capacity of a floppy disk. Select UMS models have four (4) different multimedia
ports wired into the AUX Video Input. There is one port for each of the following memory
cards:
5.2
–
Smart MediaTM (SM) (SanDisk® recommended)
–
Secure Digital/MultiMedia Card (SD/MMC) (SanDisk recommended)
–
Compact FlashTM (CF) (SanDisk recommended)
–
Sony Memory StickTM (MS)
Image Requirements
Your memory card must contain a baseline JPEG image with a recommended size of 640 x 480
pixels in its root directory. A baseline JPEG is stored as one, top-to-bottom scan of the
image. If this size is not met, the image may appear out of proportion. Use of a TIFF or other
incorrect format generates the following message:
must be base JPEG files
5.2.1
Adding Images to the Memory Card
There are two (2) ways to add images to the memory card:
–
Utilize a compatible USB card reader with your PC. Insert your compatible memory card
into the card reader and follow the instructions to copy and save desired images; then
transfer the memory card to the UMS.
–
F01U029703 | 1.0 | 2006.07
Utilize a digital camera to take photos; then transfer the memory card to the UMS.
Installation Manual
Bosch Security Systems, Inc.
UMS Series Public View System
5.2.2
Using the Card Reader | en
11
Inserting the Flash Memory Card (not provided)
1.
Insert a compatible memory card all the way into the appropriate port located on the
back of the UMS. To ensure a proper playback, you must insert the memory card correctly.
1
2
3
4
Fig. 5.1 Card Reader Insertion
Ref. # Description
1
Sony Memory StickTM input slot
2
Compact FlashTM (CF) input slot
3
Secure Digital/MultiMedia Card (SD/MMC) input slot
4
Smart MediaTM (SM) input slot
2.
Press the AUX button to display the JPEG image(s). If more than one JPEG is on the card,
the UMS displays a slide show rotating through all supplied JPEG images.
i
5.2.3
NOTICE! On units supplied with a card reader, a SanDisk remote control is included. This
remote control allows additional features to be controlled via the card reader.
Removing the Flash Memory Card
To remove your flash memory card, pull the card out.
Bosch Security Systems, Inc.
Installation Manual
F01U029703 | 1.0 | 2006.07
12
en | Card Reader Remote Control Functions (SanDisk®)
6
UMS Series Public View System
Card Reader Remote Control Functions (SanDisk®)
This section details the functions and the usage of the card reader remote control for the
UMS-20xxxC models.
Button
Function
PLAY/SLIDE SHOW Plays images continuously from
your memory card
PAUSE
Pauses the slide show
PREVIEW
Previews multiple images
POWER
Turns the card reader ON/OFF
MENU/SELECT
Selects the OSD menu
NEXT
Selects the next image
PREVIOUS
Selects the previous image
ZOOM +
Increases image zoom
ZOOM -
Decreases image zoom
ROTATE
Rotates the image to the left
ROTATE
Rotates the image to the right
DELETE
Deletes an image
Navigates up
Navigates down
Navigates right
Navigates left
6.1
Card Reader On-screen Display Menu Selections
i
NOTICE! See Section 4, Monitor Remote Control Functions (Bosch), on page 6 for information
on installing the batteries for your SanDisk remote control.
Use the memory card reader remote control to make any necessary adjustments to the images
stored on your memory card. To navigate the set up menus, follow the steps below:
1.
2.
Select the AUTO or AUX mode from the Bosch remote control.
If you have not already inserted the memory card into the appropriate port, see
Section 5.2.2, Inserting the Flash Memory Card (not provided), on page 11 for details.
3.
Use the memory card remote control (SanDisk) to activate the main menu selections.
Press the PAUSE button followed by the MENU/SELECT button. The unit displays the following menus:
F01U029703 | 1.0 | 2006.07
–
Select Memory Card
–
Display Photo Info
–
Slide Show Delay
–
TV Screen Display
–
Picture Position
–
Language
–
Exit
Installation Manual
Bosch Security Systems, Inc.
UMS Series Public View System
i
6.2
Card Reader Remote Control Functions (SanDisk®) | en13
NOTICE! The effects (called Transition Effects) that the card reader displays between images
are randomly generated and cannot be changed.
Card Reader Menu Selections
There are seven (7) on-screen main menus which allow you to customize your settings.
6.2.1
Select Memory Card Menu
The Select Memory Card menu allows you to choose the memory card you would like to
access.
Fig. 6.1 Memory Card Menu
6.2.2
Display Photo Info Menu
The Display Photo Info menu allows you to display the image information (date, time, size
of file, and resolution).
Fig. 6.2 Photo Info Menu
Bosch Security Systems, Inc.
Installation Manual
F01U029703 | 1.0 | 2006.07
14
en | Card Reader Remote Control Functions (SanDisk®)
6.2.3
UMS Series Public View System
Slide Show Delay Menu
The Slide Show Delay menu allows you to adjust the delay time (0-60 seconds) between
individual slides. To increase the number of seconds between slides, press the
arrow) button and to decrease the number of seconds between slides, press the
(right
 (left
arrow) button. When finished, press the MENU/SELECT button to accept changes.
Fig. 6.3
6.2.4
Show Delay Menu
TV Screen Display Menu
The TV Screen Display menu allows you to display images in either Full Screen mode or in
the true image size. The true image setting is best if your images are 640 x 480 pixels, the recommended size. If the original image size is greater than 640 x 480 pixels, the image is automatically resized in Full Screen mode.
Fig. 6.4
i
6.2.5
Screen Display Menu
NOTICE! When in full screen mode, there is a small black border at the bottom, left, and right
of the monitor.
Picture Position Menu
The Picture Position menu allows you to move your images to the left, right, up, and down.
To preview the changes, press the MENU/SELECT button on the memory card reader remote
control and then select the Exit option on the screen. Press the NEXT or PREVIOUS button to
view each image.
Fig. 6.5
F01U029703 | 1.0 | 2006.07
Picture Position Menu
Installation Manual
Bosch Security Systems, Inc.
UMS Series Public View System
6.2.6
Card Reader Remote Control Functions (SanDisk®) | en15
Language Menu
The Language menu allows you to switch languages for the card reader OSD.
Fig. 6.6 Language Menu
6.2.7
Exit Menu
The Exit menu allows you to exit the screen. To resume playing your images, press PLAY/
SLIDE SHOW.
Bosch Security Systems, Inc.
Installation Manual
F01U029703 | 1.0 | 2006.07
16
en | Configuring Motion Detection
7
UMS Series Public View System
Configuring Motion Detection
Passive Infrared Sensor (PIR) detectors are designed to detect movement by sensing the
infrared energy emitted from the human body as it moves across the sensor’s coverage sectors (see the shaded areas in the illustration below). The detectors emit no energy of their
own.
7.1
Selecting a Mounting Location
Mount the monitor where people will most likely cross through the coverage pattern. The PIR
sensor is at the lower right hand corner of the monitor.
1
3
4
2
Fig. 7.1
PIR Coverage Sectors
For optimum results follow these guidelines:
1.
Motion detection works best when people walk across multiple coverage sectors instead
of walking directly towards the monitor and staying within one coverage sector.
2.
3.
Position the sensor a maximum of 9.8 to 13.1 ft (4 to 5 m) from the coverage area.
Avoid aiming the monitor at sources of rapid heating or cooling. These sources include
forced air ducts, space heaters, direct sunlight, strong white lights and mirrors that
reflect strong lights.
4.
7.2
Position the sensor 7.5 to 9 ft (2.25 to 2.7 m) above the floor.
Activating the PIR
The UMS is equipped with a PIR that detects motion from a range of 3–4 m (9.8–13.1 ft). The
PIR sensor is used to control switching in the AUTO mode.
1.
Press the AUTO button on the Bosch remote control. If you have a memory card inserted,
the UMS displays the image(s) on the screen (otherwise the screen is black). For information on how to insert a memory card see Section 5.2.2, Inserting the Flash Memory Card
(not provided), on page 11.
2.
To test the motion sensor, create movement in the front, lower-right side of the UMS window. The UMS display panel switches from displaying the image(s) on the memory card
to displaying the surveillance video.
i
NOTICE! The UMS Series always transmits looping output from the internal camera to the
recording device, regardless of the operating mode.
F01U029703 | 1.0 | 2006.07
Installation Manual
Bosch Security Systems, Inc.
UMS Series Public View System
8
Camera Tilt and Pivot Adjustments | en
17
Camera Tilt and Pivot Adjustments
You can adjust the camera module position vertically and horizontally, and you can rotate the
camera module for proper tilt orientation. See Section 8.1, High-resolution Color Series Camera, on page 17 or Section 8.3, Wide Dynamic Range (WDR) Series Camera, on page 19 for your
camera series adjustment points.
8.1
High-resolution Color Series Camera
The figure below illustrates the camera adjustment points for the high-resolution, color camera.
Fig. 8.1 High-resolution, Color Camera Adjustment Points
Ref. # Description
1
Tilt adjustment; thumb nut
2
Pivot point
3
Rotate adjustment dial; used to square camera once adjustments have been made
Bosch Security Systems, Inc.
Installation Manual
F01U029703 | 1.0 | 2006.07
18
8.2
en | Camera Tilt and Pivot Adjustments
UMS Series Public View System
Dip Switch Location for the High-resolution Color Camera
The camera module has various settings for any additional adjustments that may be required.
See the illustration below and Figure 8.4 on page 19 for the correct camera series settings and
dip switch locations.
Fig. 8.2
High-resolution, Color Camera Dip Switch Location
The following chart explains the selectable dip switches and their respective functions for the
High-resolution Color Camera:
1
2
3
IRIS
DC
DC IRIS
AES
AES
ON
Shutter speed to be fixed at 1/100 second
OFF
Normal position
ON
Set to this position when a strong light is in the background
OFF
Normal position
Synchronization
INT
Internal Synchronization mode
Mode
L.L.
Linelock mode
Flickerless (FL)
Backlight
Compensation
(BLC)
4
F01U029703 | 1.0 | 2006.07
Installation Manual
Bosch Security Systems, Inc.
UMS Series Public View System
8.3
Camera Tilt and Pivot Adjustments | en
19
Wide Dynamic Range (WDR) Series Camera
The figure below illustrates the camera adjustment points for the wide dynamic range camera.
Fig. 8.3 Wide Dynamic Range (WDR) Camera Adjustment Points
8.4
Ref. #
Description
1
Tilt adjustment; thumb nut
2
Pivot point
Dip Switch Location for Wide Dynamic Range (WDR) Camera
The figure below shows the location of the dip switches for the WDR camera.
ON
1
2
Fig. 8.4 Wide Dynamic Range (WDR) Camera Dip Switch Location
The following chart explains the selectable dip switches for the Wide Dynamic Range (WDR)
Camera:
1
2
Bosch Security Systems, Inc.
WDR
WDR
ON
Camera is in WDR mode
OFF
N/A
ON
WDR
OFF
N/A
Installation Manual
F01U029703 | 1.0 | 2006.07
20
en | Camera Tilt and Pivot Adjustments
8.5
UMS Series Public View System
Focusing the Camera
Adjust the focus on the camera by adjusting the rings around the lens until the picture is sharp
and clear. If the camera is angled to one side, there is a sliding black mask behind the front
window with a hole for the camera. Adjust the camera to the proper tilt position, see
Figure 8.1 on page 17 and Figure 8.3 on page 19 for your camera series, and then slide the
black mask until none of it shows in the picture.
8.6
Light Sensor
The monitor display switches to the Power Save mode approximately one (1) minute after a
reduction in light is detected. The screen turns black and displays the following message DPMS
Power Save Mode. When the sensor detects light, the monitor automatically switches to the
ON mode.
i
NOTICE! The looping output video is still active so that external recording continues in the
Power Save mode.
F01U029703 | 1.0 | 2006.07
Installation Manual
Bosch Security Systems, Inc.
UMS Series Public View System
9
Troubleshooting | en
21
Troubleshooting
The following are commonly asked troubleshooting questions to better assist you in operating
your UMS monitor.
9.1
Make adjustments to the control board and option switches
The control board is a microprocessor-based circuit that controls the on-board sensors and a
two (2) channel video switcher. The main purpose of the switcher is to display the image from
the on-board camera when the PIR detects motion. It may also be directed to ignore the sensor and select one of the two (2) video signals.
The following figure details the control board and the option switches:
Fig. 9.1 Control Board Configuration
Ref. # Description
1
Camera ON LED (red)
2
System Pulse LED (red)
3
System Power LED (green)
4
Option Switches (see Figure 9.2 on page 22 for details)
5
RS-232 (factory use only)
6
LCD Monitor Video
7
Aux Video In
8
Internal Camera Video Out Loop
9
Video In
10
Reserved for future use
11
Power Connector
12
Phase Control
13
Power to Camera
.
Bosch Security Systems, Inc.
Installation Manual
F01U029703 | 1.0 | 2006.07
22
en | Troubleshooting
UMS Series Public View System
The following figure illustrates the option switches and their default settings:
Fig. 9.2
Option Switch Details
#
Control
Default Setting
Function
1
Motion Switcher
ON
Enables motion switcher
OFF
Disables motion switcher
ON
Not used
OFF
Not used
ON
Sync to Aux video
OFF
Sync to line
ON
Enables light sensor
OFF
Disables light sensor
2
3
4
Not Used
Synchronization Mode
Light Sensor
To verify the operation of the control board and to make any necessary adjustments to the
option switches, follow these steps:
1.
Manually unscrew the two (2) thumbscrews on the back of the unit. The control board
LED’s are located on the control board to the left of the camera. See Figure 9.1 on page
21, numbers 1-3.
–
Verify that the Camera On LED is red when the camera input is selected and Off
–
Verify that the System Pulse LED is red, signifying that the control board is run-
–
Verify that the System Power LED is green, signifying that the UMS is ON.
when the auxiliary input is selected.
ning.
2.
Verify the four (4) Option Switches are set to the default settings (see Figure 9.2 on page
22 for details on the respective functions).
9.2
Screen flickers
The most likely cause of a flickering screen is a power supply problem. Ensure that there is
proper AC voltage to the monitor. Running wires long distances from the power supply may
cause undesirable voltage loss. For running power longer distances, it is recommended that
you use a heavier wire gauge. Refer to a copper wire table and line loss table for exact engineering specifications.
Below is a table of maximum distances that the specified wire gauges can traverse with a 24 V
transformer:
Gauge
Distance
Gauge
Distance
20 AWG
40 ft
14 AWG
170 ft
18 AWG
70 ft
12 AWG
270 ft
16 AWG
100 ft
F01U029703 | 1.0 | 2006.07
Installation Manual
Bosch Security Systems, Inc.
UMS Series Public View System
9.3
Troubleshooting | en
23
No video displayed
1.
Check that the power cable is properly inserted and that the power outlet has the proper
voltage. Make sure that the power switch located is ON.
2.
If power is supplied to the unit:
a.
Open the cover to the UMS.
b.
Press the CAM button on the Bosch remote control.
c.
Check if the Monitor Power LED is illuminated green (see Figure 9.3 on page 24 for
location and definitions).
3.
If the Monitor Power LED is not illuminated:
a.
Press the Power button next to the Monitor Power LED to activate the unit. The
Monitor Power LED illuminates green, indicating that power is flowing to the monitor.
4.
If the Monitor Power LED is amber:
a.
Ensure that the Monitor Power Connector is secure. See Figure 9.3 on page 24 for
the location of this connector.
b.
Check the lighting conditions in the area of the UMS camera. If the area is too dark
the light sensor keeps the UMS in Power Save mode. To disable the light sensor, set
the Number 4 option switch, located on the control board, to the OFF position. See
Figure 9.2 on page 22 for details.
c.
Unplug the the cable from the yellow RCA Jack (see Figure 9.3 on page 24 for the
location) and plug in an alternate video source in this location, such as a DVD player
or test pattern generator.
d.
If the alternate video source is detected, please contact Bosch Security Systems for
further instructions.
5.
If the alternate video source is not detected:
a.
Press the MENU button on the Bosch remote control.
b.
Press the
 button until you navigate to the Input Select menu.
c.
Press the
button to navigate to Video, then select it using the
button as the
input source.
d.
e.
Check if the monitor displays video on the screen.
If video is displayed on the screen, press the POWER button next to the Monitor
Power LED to turn the monitor OFF; this action saves the settings.
f.
6.
Press the POWER button again to re-activate the monitor.
If there is still no video displayed, contact your Bosch Security Systems representative or
customer service.
9.4
Only displays Power Save mode
In this case, the Video option on the Input Select menu may be OFF. To verify this setting,
do the following:
1.
Press the MENU button on the Bosch remote control.
2.
When the monitor displays the message DPMS Power Save Mode, press MENU again.
The monitor displays the Input Select menu.
3.
Ensure that the video option is ON (see Figure 4.4 on page 9).
4.
If Video is not ON, use either your
or
button to select Video, then press the
but-
ton to automatically display video on the monitor.
Bosch Security Systems, Inc.
Installation Manual
F01U029703 | 1.0 | 2006.07
24
9.5
en | Troubleshooting
UMS Series Public View System
Remote control does not activate the monitor
–
Make sure that you are pointing the infrared end of the transmitter toward the bottom of
the monitor.
–
Make sure that you are within 9.8–13.1 ft (4–5 m) of the unit.
–
Make sure that the batteries in the remote control are inserted correctly (see Figure 3.2
on page 5) and are strong enough to power the controller.
9.6
Lost remote control
It is recommended to use the Bosch remote control to configure the unit (see
Section 4, Monitor Remote Control Functions (Bosch), on page 6). If you lose either remote
control, call your Bosch Security Systems representative and order kit number: 315 5531 925.
This kit contains the Bosch branded remote, a SanDisk remote, and batteries.
If the Bosch remote control is not available, it is possible to navigate through the screens by
using the buttons on the back of your unit. See the image below for the location for the these
buttons:
Fig. 9.3
Internal Monitor Controls
Ref. # Description
1
Calls up the menu on the monitor
2
Selects an item from the menu
3
Scrolls down
4
Scrolls up
5
Monitor Power LED display light
Green: Indicates Video On
Amber: Indicates Video Loss
6
Powers the unit ON and OFF
7
Monitor Power Connector
8
Video In (yellow) RCA Jack
F01U029703 | 1.0 | 2006.07
Installation Manual
Bosch Security Systems, Inc.
UMS Series Public View System
9.7
Troubleshooting | en
25
Memory card images appear stretched and out of proportion
The recommended size for images is 640 x 480 pixels (1.33 ratio). If the image was loaded
without meeting this specification, the image may look out of proportion. To confirm the true
size of your photo, follow these steps:
1.
2.
Press either the AUTO or AUX button on the Bosch remote control.
Press the PAUSE button and then press the MENU/SELECT button on the SanDisk remote
control.
3.
Scroll down to Display Photo Info, and press the MENU/SELECT button.
4.
Scroll down to ON and press the MENU/SELECT button.
5.
Scroll down to the Exit menu and press the MENU/SELECT button. The menu displays
the image number, the date and time it was loaded, the size of the image, and the pixel
size.
i
9.8
NOTICE! The Display Photo Info setting must be set to OFF if you do not want this
information displayed throughout your slide show.
Images are smaller than the recommended size
You can choose to display your images at their true size by following these steps:
1.
Press either the AUTO or AUX button on the Bosch remote control.
2.
Press the PAUSE button and then press the MENU/SELECT button on the SanDisk remote
control.
3.
Scroll down to TV Screen Display and press the MENU/SELECT button.
4.
Scroll down to True Image and press the MENU/SELECT button.
5.
Scroll down to the Exit menu and press the MENU/SELECT button. The image should be
correctly proportioned, however, it may not take up the entire screen.
9.9
Question marks are displayed in the preview mode
An incorrect image format is displayed with question marks. Delete those images.
9.10
Movie clips do not play
The internal card reader is not compatible with movie clips.
9.11
Card reader does not display images
–
Verify that the memory card is pushed in the whole way.
–
Verify that your memory card contains only baseline JPEG image(s) in its root directory.
The monitor displays the following message:
must be base JPEG files
if a TIFF or other incorrect file format is loaded into the UMS.
–
Verify that the memory card is compatible with the memory card reader hardware. See
Section 5.1, Compatible Flash Memory Cards, on page 10 for a list of compatible memory
cards.
–
Verify that the memory card is properly inserted into the memory card reader and that
there are no damaged pins.
Bosch Security Systems, Inc.
Installation Manual
F01U029703 | 1.0 | 2006.07
26
en | Troubleshooting
9.12
UMS Series Public View System
Monitor does not display AUTO or AUX video when turned on
–
Ensure that the MEM button on the monitor remote control (Bosch) was used to save the
operating mode.
–
Press the AUTO or AUX button on the monitor remote control (Bosch). If you pressed the
On/Off buttons on either remote, the display always returns to the CAM mode.
F01U029703 | 1.0 | 2006.07
Installation Manual
Bosch Security Systems, Inc.
UMS Series Public View System
UMS Ordering Information | en
10
UMS Ordering Information
10.1
Power Supply
Part Number
Description
UMP-24V4P0-60
Power Supply:
27
Single output, 120/24 VAC, 60 Hz, 4 A, with a 6 ft power cord and a steel
enclosure
10.2
Mounting Options
Part Number
Description
UMM-LP10B
Feed-through Pipe Mount:
Includes feed-through ball joint, 10 in. stem and pipe coupling, black
UMM-LW10B
Feed-through Flange/Wall Mount:
Includes feed-through ball joint, 12 in. stem and wall flange, black
10.3
Replacement Parts
Part Number
Description
UMS-CMS36
Camera Replacement Kit:
One (1) color high resolution camera with 3–6 mm lens
UMS-CMW39
Camera Replacement Kit:
One (1) wide dynamic camera with 3.8–9.5 mm lens
315 5531 925
Remote Control Replacement Kit:
One (1) Monitor Remote Control (Bosch)
One (1) Memory Card Reader Remote Control (SanDisk)
Four (4) AAA Batteries
Bosch Security Systems, Inc.
Installation Manual
F01U029703 | 1.0 | 2006.07
28
11
en | Specifications
UMS Series Public View System
Specifications
Electrical
Rated Voltage
Voltage Range
Power at Rated
Voltage
Sync. Format
LCD Panel
Screen Size
(H x V)
Viewable Picture
Area
Pixel Pitch
(H x V)
Resolution (H x V)
Aspect Ratio
Display Colors
Response Time
Backlight
Mechanical
Cabinet
24 VAC, 60 Hz
22-26 VAC
80 W/100 VA
Mounting
NTSC
TFT LCD
16.06 x 12.05 in.
(408 x 306 mm)
20.1 in. (51 cm) measured diagonally
0.6375 x 0.6375 mm
640 x 480 pixels
4:3 Composite Video
8-bit interface; 16.8 million colors
25 ms
Six (6) cold cathode fluorescent tubes, rated life
50,000 hours
Optical Characteristics
Luminance
450 cd/m2
Contrast Ratio
350:1
Viewing Angle
176° horizontal, 176° vertical
Video Input (UMS-20xxxA models only)
Composite Video
Aux video input from external source
(CVBS)
1.0 Vp-p (0.5–1.5 Vp-p), 75 Ohm
Video Output (UMS-20xxxC models only)
Composite Video
Looping video out from Video 1 ( internal camera)
(CVBS)
1.0 Vp-p (0.5–1.5 Vp-p), 75 Ohm
Controls
Remote Control
Monitor Remote: On/Off; Monitor Setup; Video
Input Selection – Aux/Camera
Memory Card Reader Remote: On/Off; Card
Reader Setup; Slideshow Controls
Switcher
2 Channels CAM/AUX, dwell time: 15 sec.
Sensors
Light Sensor
Display switches to Power Save mode upon light
reduction (1 min. delay)
Motion Detection
Built-in PIR Motion detector switches unit from Aux
to Camera upon activation (Range 3-4 m)
Memory Card Reader
Content Format Support: JPEG (baseline: 640 x 480)
Compatible Flash Memory Card Formats: SmartMedia™ (SM), Secure
Digital/MultiMedia Card (SD/MMC), Compact Flash™ (CF), Sony Memory
Stick™ (MS)
F01U029703 | 1.0 | 2006.07
Dimensions
(W x D x H)
Weight
(unit without mount)
Shipping Weight
Environmental
Operating Temp.
Storage Temp.
Humidity
Camera
Specification
Camera Type
Horizontal Resolution
Sensitivity (minimum
scene illumination f/
1.2 lens, 50 IRE)
Imager
System
Signal to Noise
Iris Control
Flickerless
Backlight
Compensation
White Balance
Video Output
Synchronization
Phase Adjust
Controls
Lens
Focal Range
Iris Range
Iris/Shutter
Format
Installation Manual
Material: Aluminum with acrylic front window
Finish: Powder coated black
Mounting pattern 75 mm and 100 mm square,
threaded 10-24
17.9 x 2.8 x 16.5 in.
(454.7 x 71.12 x 419.1 mm)
13 lbs (5.9 Kg)
17 lbs (7.71 Kg)
0°C to 40°C (32°F to 104°F)
–20°C to 60°C (–4°F to 140°F)
10%–95%, non-condensing
S36
W39
StandardHigh
Resolution Color
Camera
Wide Dynamic Range
(WDR) Camera
480 TVL
0.5 lux (30 IRE)
1.2 lux (50 IRE)
1/4-in. image
format;
interline transfer
CCD
1/3-in. image format;
double scan CCD
NTSC
50 dB
DC Iris electronic shutter 1/60 sec. fixed
Electronic shutter 1/100 sec. fixed
Selectable On/Off
N/A
control
Automatic sensing through the lens (TTL
system):+2700 K to 9000 K
Composite; 1.0 Vp-p, 75 Ohm
Line-lock / crystal mode
0° to 330°
Line-lock On/Off;
Line-lock On/Off
Backlight
compensation;
Flickerless On/Off
3-6 mm
f/1.2-360
1/4 in.
3.8-9.5 mm
f/1.3-360
DC Auto Iris
1/3 in.
Bosch Security Systems, Inc.
UMS Series Public View System
Specifications | en
29
Connector
Video In
RCA (CAM, used by internal camera)
UMS-20xxxC-xx
RCA (AUX, used by card reader)
UMS-20xxxA-xx
BNC (video in from external video source)
Video Out
BNC
Power
Flying leads
Accessories
Feed-thru Pipe Mount
Feed-thru ball joint , 10-in.
UMM-LP10B
stem and pipe coupling
Monitor Type
LCD monitors only
Maximum Load
25 lbs (11.34 Kg)
Pan Range
0° to 360°
Tilt Range
0° to 30°
Material
Aluminum
Finish
Black
Weight
3.53 lbs (1.6 Kg)
Feed-thru Flange/Wall Mount Feed-thru ball joint, 12-in.
UMM-LW10B
stem and wall flange
Monitor Type
LCD monitors only
Maximum Load
25 lbs (11.34 Kg)
Pan Range
0° to 180°
Tilt Range
0° to 30°
Material
Aluminum
Finish
Black
Weight
2.65 lbs (1.2 Kg)
Power Supply
6 ft power cord and a steel
UMP-24V4P0-60
enclosure
Voltage Range
95 to 144 VAC
Rated Input
120 VAC, 60 Hz
Rated Output
24 VAC, 60 Hz, 4 A
Dimensions (W x D x H)
4.5 x 5.0 x 3.6 in.
(114.3 x 127 x 91.44 mm)
Material
Steel case
Finish
Powder-coated white
Input Power Connector
Detachable, 3-wire IEC
grounded plug
Output Power Connector
Screw terminal block
Safety
UL, cUL
Bosch Security Systems, Inc.
Installation Manual
F01U029703 | 1.0 | 2006.07
30
en | Specifications
F01U029703 | 1.0 | 2006.07
UMS Series Public View System
Installation Manual
Bosch Security Systems, Inc.
UMS Series Public View Monitor
A
Accessories
mounts 27
power supply 27
replacement parts 27
Adjusting
backlight 8
blending 8
brightness 8
camera position 17, 19
color 8
contrast 8
control board 21
dip switch 18
focus 20
horizontal position 8
languages 8
mirroring 9
pivot 17, 19
sharpness 8
tilt 17, 19
tint 8
vertical position 8
AES 18
AUTO mode 7, 12
AUX mode 7, 12
AUX video input 10
B
Backlight compensation 18
Backlight option 8
Blending option 8
Bosch remote control 16, 24
Brightness option 8
C
CAM mode 7
Camera ON LED 21
Camera On LED 22
Card reader 10, 12
Color option 8
Connections
video in 4
video out 4
Contrast option 8
Control board 21
D
Defaults 9
Delay time 14
Digital camera 10
Dip switch 18, 19
Display aspect option 9
Display Photo Info menu 13, 25
E
Exit menu 15
F
Factory preset option 9
Flash memory 10
Flickerless 18
Focus 20
Full-screen mode 14
Bosch Security Systems, Inc.
| en
31
H
Horizontal position option 8
I
Information option 9
Input Select menu 9
Installation 3
mounting 3
power 3
power connection 4
Internal Synchronization mode 18
Iris 18
J
JPG file 10
JPG image 6
L
Language menu 15
Languages 8
Light sensor 2, 20, 22, 23
Linelock mode 18
M
Menus
Bosch 7
Input Select 9
Misc. 9
OSD 8
Video 8
card reader
Display Photo Info 13
Exit 15
Language 15
Picture Position 14
Slide Show Delay 14
TV Screen Display 14
Mirroring option 9
Misc. menu 9
Modes
AUTO 7
AUX 7, 12
CAM 7
Full-screen 14
Internal Synchronization 18
Linelock 18
Power Save 9, 20, 23
Synchronization 22
WDR 19
Monitor power
connector 23, 24
LED 23, 24
Motion detection 16
Motion sensor 2
Motion switcher 22
Mounts 3, 27
specifications for motion detection 16
UMM-LP10B 27
UMM-LW10B 27
Installation Manual
F01U029703 | 1.0 | 2006.07
32
en |
O
On-screen display 6, 7
Option switch 22
Options
backlight 8
blending 8
brightness 8
color 8
contrast 8
display aspect 9
factory preset 9
horizontal position 8
information 9
mirroring 9
sharpness 8
tint 8
upside down 9
vertical position 8
OSD menu 8
P
Passive Infrared Sensor (PIR) 16
range 16
Phase control 21
Picture Position menu 14
Pivot 17, 19
Power 3
Power connection 4
Power connector 21
Power Save mode 9, 20, 23
Power supply 4, 27
UMP-24V4P0-60 4
R
RCA jack 23, 24
Remote control 5
battery installation 5
Bosch 24
menus 7
operating mode 7
card reader 12
replacement kit 27
SanDisk 11, 12
Replacement parts 27
Resetting defaults 9
Root directory 10
RS-232 21
UMS Series Public View Monitor
T
Tilt 17, 19
Tint option 8
Transformer 4
Troubleshooting 21
black screen 23
control board 21
flicker 22
image size 25
images 25
lost remote control 24
movie clips 25
no video 23
option switch 21
remote control 24
True image size 14
TV Screen Display menu 14
U
UMM-LP10B 27
UMM-LW10B 27
UMP-24V4P0-60 4, 27
UMS-CMS36 27
UMS-CMW39 27
Upside down option 9
USB card reader 10
V
Vertical position option 8
Video In connection 4
Video menu 8
Video Out connection 4
Video switcher 21
Voltage loss 22
W
Wago clamp 1
WDR mode 19
Wire gauge 22
S
SanDisk 12
remote control 11, 12
Select 13
Select Memory Card menu 13
Sharpness option 8
Slide Show Delay menu 14
Specifications 2, 28
power 3
Synchronization mode 22
System Power LED 21, 22
System Pulse LED 21
F01U029703 | 1.0 | 2006.07
Installation Manual
Bosch Security Systems, Inc.
Americas:
Bosch Security Systems
130 Perinton Parkway
Fairport, New York, 14450
USA
Phone
+1 800 289 0096
Fax
+1 585 223 9180
www.boschsecurity.us
© Bosch Security Systems, Inc., 2006
Europe, Middle East, Asia:
Bosch Security Systems B.V.
Postbus 80002
5600 JB Eindhoven
Phone:
+31 40 2577 200
Fax:
+31 40 2577 202
nl.securitysystems@bosch.com
www.boschsecurity.nl
www.boschsecurity.com
Asia-Pacific:
Bosch Security Systems Pte Ltd.
38C Jalan Pemimpin
Singapore 577180
Phone
+65 6319 3450
Fax
+65 63139 3499
www.boschsecurity.com