Yamaha CP-20 Owner`s manual

OWNER’S MANUAL
STAGE PIANO
EN
SPECIAL MESSAGE SECTION
PRODUCT SAFETY MARKINGS: Yamaha electronic
products may have either labels similar to the graphics
shown below or molded/stamped facsimiles of these graphics on the enclosure. The explanation of these graphics
appears on this page. Please observe all cautions indicated
on this page and those indicated in the safety instruction section.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The exclamation point within the equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the
product.
The lightning flash with arrowhead symbol, within the equilateral triangle, is
intended to alert the user to the presence
of uninsulated “dangerous voltage”
within the product’s enclosure that may
be of sufficient magnitude to constitute a
risk of electrical shock.
IMPORTANT NOTICE: All Yamaha electronic products
are tested and approved by an independent safety testing
laboratory in order that you may be sure that when it is properly installed and used in its normal and customary manner,
all foreseeable risks have been eliminated. DO NOT modify
this unit or commission others to do so unless specifically
authorized by Yamaha. Product performance and/or safety
standards may be diminished. Claims filed under the
expressed warranty may be denied if the unit is/has been
modified. Implied warranties may also be affected.
SPECIFICATIONS SUBJECT TO CHANGE: The information contained in this manual is believed to be correct at
the time of printing. However, Yamaha reserves the right to
change or modify any of the specifications without notice or
obligation to update existing units.
92-469- ➀ (rear)
2
CP300 Owner’s Manual
ENVIRONMENTAL ISSUES: Yamaha strives to produce
products that are both user safe and environmentally
friendly. We sincerely believe that our products and the production methods used to produce them, meet these goals. In
keeping with both the letter and the spirit of the law, we
want you to be aware of the following:
Battery Notice: This product MAY contain a small nonrechargeable battery which (if applicable) is soldered in
place. The average life span of this type of battery is approximately five years. When replacement becomes necessary,
contact a qualified service representative to perform the
replacement.
Warning: Do not attempt to recharge, disassemble, or incinerate this type of battery. Keep all batteries away from children. Dispose of used batteries promptly and as regulated by
applicable laws. Note: In some areas, the servicer is required
by law to return the defective parts. However, you do have
the option of having the servicer dispose of these parts for
you.
Disposal Notice: Should this product become damaged
beyond repair, or for some reason its useful life is considered to be at an end, please observe all local, state, and federal regulations that relate to the disposal of products that
contain lead, batteries, plastics, etc.
NOTICE: Service charges incurred due to lack of knowledge relating to how a function or effect works (when the
unit is operating as designed) are not covered by the manufacturer’s warranty, and are therefore the owners responsibility. Please study this manual carefully and consult your
dealer before requesting service.
NAME PLATE LOCATION: The graphic below indicates
the location of the name plate. The model number, serial
number, power requirements, etc., are located on this plate.
You should record the model number, serial number, and the
date of purchase in the spaces provided below and retain this
manual as a permanent record of your purchase.
AC INLET
Model
Serial No.
Purchase Date
ASSIGNABLE FOOT PEDAL
3
1
2
SOFT
SUSTAIN SOSTENUTO
4
AUX
IN
MIDI
OUT
USB
THRU
OUTPUT
R
L
R
OUTPUT
L/MONO
R
INPUT
L/MONO
IMPORTANT SAFETY INSTRUCTIONS
INFORMATION RELATING TO PERSONAL INJURY, ELECTRICAL SHOCK,
AND FIRE HAZARD POSSIBILITIES HAS BEEN INCLUDED IN THIS LIST.
WARNING- When using any electrical or electronic product,
basic precautions should always be followed. These precautions
include, but are not limited to, the following:
8.
This product was NOT designed for use in wet/damp locations and should not be used near water or exposed to rain. Examples of wet/damp locations are; near a swimming pool, spa, tub,
sink, or wet basement.
1.
9.
2.
10.
Read all Safety Instructions, Installation Instructions, Special Message Section items, and any Assembly Instructions found
in this manual BEFORE making any connections, including connection to the main supply.
Main Power Supply Verification: Yamaha products are
manufactured specifically for the supply voltage in the area where
they are to be sold. If you should move, or if any doubt exists about
the supply voltage in your area, please contact your dealer for supply voltage verification and (if applicable) instructions. The
required supply voltage is printed on the name plate. For name
plate location, please refer to the graphic found in the Special Message Section of this manual.
3.
This product may be equipped with a polarized plug (one
blade wider than the other). If you are unable to insert the plug into
the outlet, turn the plug over and try again. If the problem persists,
contact an electrician to have the obsolete outlet replaced. Do NOT
defeat the safety purpose of the plug.
4.
Some electronic products utilize external power supplies or
adapters. Do NOT connect this type of product to any power supply or adapter other than one described in the owners manual, on
the name plate, or specifically recommended by Yamaha.
5.
WARNING: Do not place this product or any other objects
on the power cord or place it in a position where anyone could
walk on, trip over, or roll anything over power or connecting cords
of any kind. The use of an extension cord is not recommended! If
you must use an extension cord, the minimum wire size for a 25’
cord (or less) is 18 AWG. NOTE: The smaller the AWG number,
the larger the current handling capacity. For longer extension
cords, consult a local electrician.
6.
Ventilation: Electronic products, unless specifically
designed for enclosed installations, should be placed in locations
that do not interfere with proper ventilation. If instructions for
enclosed installations are not provided, it must be assumed that
unobstructed ventilation is required.
7.
This product should be used only with the components
supplied or; a cart, rack, or stand that is recommended by the manufacturer. If a cart, rack, or stand is used, please observe all safety
markings and instructions that accompany the accessory product.
The power supply cord (plug) should be disconnected from
the outlet when electronic products are to be left unused for
extended periods of time. Cords should also be disconnected when
there is a high probability of lightning and/or electrical storm activity.
11.
Care should be taken that objects do not fall and liquids are
not spilled into the enclosure through any openings that may exist.
12.
Electrical/electronic products should be serviced by a qualified service person when:
a. The power supply cord has been damaged; or
b. Objects have fallen, been inserted, or liquids have been
spilled into the enclosure through openings; or
c. The product has been exposed to rain: or
d. The product dose not operate, exhibits a marked change
in performance; or
e. The product has been dropped, or the enclosure of the
product has been damaged.
13.
Do not attempt to service this product beyond that
described in the user-maintenance instructions. All other servicing
should be referred to qualified service personnel.
14.
This product, either alone or in combination with an amplifier and headphones or speaker/s, may be capable of producing
sound levels that could cause permanent hearing loss. DO NOT
operate for a long period of time at a high volume level or at a level
that is uncomfortable. If you experience any hearing loss or ringing
in the ears, you should consult an audiologist.
IMPORTANT: The louder the sound, the shorter the time period
before damage occurs.
15.
Temperature considerations: Electronic products should be
installed in locations that do not significantly contribute to their
operating temperature. Placement of this product close to heat
sources such as; radiators, heat registers and other devices that produce heat should be avoided.
Some Yamaha products may have benches and/or accessory mounting fixtures that are either supplied as a part of the product or as optional accessories. Some of these items are designed to
be dealer assembled or installed. Please make sure that benches are
stable and any optional fixtures (where applicable) are well secured
BEFORE using. Benches supplied by Yamaha are designed for
seating only. No other uses are recommended.
PLEASE KEEP THIS MANUAL
92-469-2
CP300 Owner’s Manual
3
PRECAUTIONS
PLEASE READ CAREFULLY BEFORE PROCEEDING
* Please keep this manual in a safe place for future reference.
WARNING
Always follow the basic precautions listed below to avoid the possibility of serious injury or even death from electrical
shock, short-circuiting, damages, fire or other hazards. These precautions include, but are not limited to, the following:
Power supply/Power cord
Water warning
• Only use the voltage specified as correct for the instrument. The required
voltage is printed on the name plate of the instrument.
• Check the electric plug periodically and remove any dirt or dust which may have
accumulated on it.
• Do not expose the instrument to rain, use it near water or in damp or wet
conditions, or place containers on it containing liquids which might spill into
any openings.
• Never insert or remove an electric plug with wet hands.
• Use only the supplied power cord/plug.
• Do not place the power cord near heat sources such as heaters or radiators, and
do not excessively bend or otherwise damage the cord, place heavy objects on
it, or place it in a position where anyone could walk on, trip over, or roll anything
over it.
Fire warning
• Do not put burning items, such as candles, on the unit.
A burning item may fall over and cause a fire.
If you notice any abnormality
Do not open
• Do not open the instrument or attempt to disassemble the internal parts or
modify them in any way. The instrument contains no user-serviceable parts. If it
should appear to be malfunctioning, discontinue use immediately and have it
inspected by qualified Yamaha service personnel.
• If the power cord or plug becomes frayed or damaged, or if there is a sudden
loss of sound during use of the instrument, or if any unusual smells or smoke
should appear to be caused by it, immediately turn off the power switch,
disconnect the electric plug from the outlet, and have the instrument inspected
by qualified Yamaha service personnel.
CAUTION
Always follow the basic precautions listed below to avoid the possibility of physical injury to you or others, or damage
to the instrument or other property. These precautions include, but are not limited to, the following:
Power supply/Power cord
Location
• When removing the electric plug from the instrument or an outlet, always hold
the plug itself and not the cord. Pulling by the cord can damage it.
• Remove the electric plug from the outlet when the instrument is not to be used
for extended periods of time, or during electrical storms.
• Do not expose the instrument to excessive dust or vibrations, or extreme cold or
heat (such as in direct sunlight, near a heater, or in a car during the day) to
prevent the possibility of panel disfiguration or damage to the internal
components.
• Do not connect the instrument to an electrical outlet using a multiple-connector.
Doing so can result in lower sound quality, or possibly cause overheating in the
outlet.
• Do not use the instrument in the vicinity of a TV, radio, stereo equipment,
mobile phone, or other electric devices. Otherwise, the instrument, TV, or radio
may generate noise.
• Do not place the instrument in an unstable position where it might accidentally
fall over.
• Before moving the instrument, remove all connected cables.
• When setting up the instrument, make sure that the AC outlet you are using is
easily accessible. If some trouble or malfunction occurs, immediately turn off
the power switch and disconnect the plug from the outlet.
• Do not place the instrument against a wall (allow at least 3 cm/one-inch from
the wall), since this can cause inadequate air circulation, and possibly result in
the instrument overheating.
4
CP300 Owner’s Manual
(1)B-9
1/2
Connections
• Before connecting the instrument to other electronic components, turn off the
power for all components. Before turning the power on or off for all
components, set all volume levels to minimum. Also, be sure to set the volumes
of all components at their minimum levels and gradually raise the volume
controls while playing the instrument to set the desired listening level.
Maintenance
• When cleaning the instrument, use a soft, dry or slightly damp cloth. Do not use
paint thinners, solvents, cleaning fluids, or chemical-impregnated wiping
cloths.
Handling caution
• Do not insert a finger or hand in any gaps on the instrument.
• Never insert or drop paper, metallic, or other objects into the gaps on the panel
or keyboard. If this happens, turn off the power immediately and unplug the
power cord from the AC outlet. Then have the instrument inspected by qualified
Yamaha service personnel.
• Do not place vinyl, plastic or rubber objects on the instrument, since this might
discolor the panel or keyboard.
• Do not rest your weight on, or place heavy objects on the instrument, and do not
use excessive force on the buttons, switches or connectors.
• Do not operate the instrument for a long period of time at a high or
uncomfortable volume level, since this can cause permanent hearing loss. If you
experience any hearing loss or ringing in the ears, consult a physician.
Saving data
Saving and backing up your data
• Current memory data (see page 82) is lost when you turn off the power to the
instrument. Save the data to the storage memory (see page 82)/external device
such as a computer.
Saved data may be lost due to malfunction or incorrect operation. Save
important data to external device such as a computer.
Yamaha cannot be held responsible for damage caused by improper use or
modifications to the instrument, or data that is lost or destroyed.
Always turn the power off when the instrument is not in use.
(1)B-9
2/2
CP300 Owner’s Manual
5
Introduction
Introduction
Thank you for choosing the Yamaha Stage Piano CP300. The CP300 features exceptionally high-quality
sound, comprehensive features and a variety of editing functions—making it suitable for a wide range of
applications, including live performance and recording.
We recommend that you read this manual carefully so that you can fully take advantage of the advanced and
convenient functions of the CP300. We also recommend that you keep this manual in a safe and handy place
for future reference.
About this Owner’s Manual
This manual consists of four main sections: Introduction, Basic Operation, Reference and Appendix.
Introduction (page 6)
Please read this section first.
Basic Operation (page 20)
This section explains the basic functions and how to use them in detail.
Refer to this section while you play the CP300.
Reference (page 53)
This section explains how to make detailed settings for the CP300’s various functions. Refer to this section as
necessary.
Appendix (page 94)
This section contains important reference material, including Voice and Drum Kit lists, and various detailed
charts and tables.
• The illustrations and LCD displays as shown in this Owner’s Manual are for instructional purposes only, and may
appear somewhat different from those on your instrument.
Copying of the commercially available musical data including but not limited to MIDI data and/or audio data is strictly
prohibited except for your personal use. If you wish to use such data for occasions other than personal use, consult a
copyright expert.
This product incorporates and bundles computer programs and contents in which Yamaha owns copyrights or with respect
to which it has license to use others’ copyrights. Such copyrighted materials include, without limitation, all computer
software, style files, MIDI files, WAVE data, musical scores and sound recordings. Any unauthorized use of such programs
and contents outside of personal use is not permitted under relevant laws. Any violation of copyright has legal
consequences. DON’T MAKE, DISTRIBUTE OR USE ILLEGAL COPIES. This device is capable of using various types/
formats of music data by optimizing them to the proper format music data for use with the device in advance. As a result,
this device may not play them back precisely as their producers or composers originally intended.
Trademarks
• Windows is the registered trademark of Microsoft® Corporation.
• Apple and Macintosh are trademarks of Apple Computer, Inc.
• The company names and product names in this Owner’s Manual are the trademarks or registered trademarks of their
respective companies.
6
CP300 Owner’s Manual
Introduction
Supplied Accessories
• Power cord
• Foot pedal (FC3)
• Owner’s Manual
Main Features
The CP300 gives you the ultimate acoustic grand piano sound—utilizing three-stage dynamic sampling,
providing the ability to change tone with the sustain pedal, and adding a subtle, authentic release sound when
you lift your fingers from the keys.
Among the advanced features are:
• 88-key “Graded Hammer” keyboard with action that is virtually indistinguishable from an actual acoustic
piano.
• Sophisticated AWM synthesis engine and tone generation system, with a maximum polyphony of 128 notes.
Using AWM, the CP300 has 50 original Voices—including a variety of ultra-realistic piano and other
keyboard Voices, plus a wealth of authentic sounds of virtually every instrument type.
• High-grade five-band Master EQ, which enables you to control the tone intuitively using sliders on the
panel.
• Luscious reverb and chorus effects, plus an enormous variety of other effects that add extraordinary depth
and expression to your sound.
• Comprehensive MIDI functions for use with other devices and in larger music production systems.
• Four pedal connectors for maximum expressive capabilities—especially ideal for live performance—and
built-in high-quality stereo speakers.
• A powerful, versatile Performance function, which lets you store and instantly recall your custom CP300
settings, including Dual/Split configurations, Voice and effect parameters, MIDI transmit/receive channel
values and Master Edit settings.
• Built-in 16-track sequencer for recording and playing back your keyboard performance, as well as for
creating complex multi-instrument arrangements and Songs—up to a maximum 16 parts.
• Master mode, which allows you to independently control up to four external tone generators.
• Comprehensive selection of inputs/outputs and interfaces—including two separate stereo output pairs,
stereo inputs, MIDI terminals, and a USB connector.
CP300 Owner’s Manual
7
Introduction
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Application Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Before Using the CP300 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Power Supply Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Using the Pedals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Using Headphones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Turning the Power On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Adjusting the Brightness of the Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Setting the Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Playing the keyboard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Playing the Sounds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Basic Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Display Settings—Basic Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Restoring the Factory-programmed Settings of the CP300 . . . . . . . . . . . . . . . . . . 16
Basic Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Basic Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Control Names and Functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Quick Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Listening to the Demo Songs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Playing Voices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Playing Different Voices Simultaneously . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Changing the Volume for Each Part (Zone Control) . . . . . . . . . . . . . . . . . . . . . . . 28
Combining Voices—Dual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Playing Different Voices with the Left and Right Hands—Split . . . . . . . . . . . . . . . 31
Using the Pedals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Bending Notes—Pitch Bend Wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Adding a Vibrato Effect to the Sound—Modulation Wheel . . . . . . . . . . . . . . . . . . 34
Enhancing the Sound with Reverb and Chorus . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Equalizer (EQ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Key Transposition—Transpose . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Using the Click . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Using the Master Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Selecting a Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Recording Your Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Recording Your Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Re-recording Parts of a Song . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Other Recording Techniques. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Song Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Playing Back a Song . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Convenient Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Panel Lock Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
MIDI Transmission On/Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
8
CP300 Owner’s Manual
Introduction
MIDI Panic Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Built-in Speakers On/Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Reference Section . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Master Settings—Master Edit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Detailed Settings for the Voices—Voice Edit . . . . . . . . . . . . . . . . . . . . 56
Voice Edit—Basic Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Detailed Settings for MIDI Operations—MIDI Settings . . . . . . . . . . . . 63
About MIDI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
MIDI Settings—Basic Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Miscellaneous CP300 Settings—Other Settings . . . . . . . . . . . . . . . . . 67
Other Settings—Basic Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Master Equalizer Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Using the Performance Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Performance Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Handling Performance Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Performance File—Basic Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Handling Song Files . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Song File—Basic Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
Settings for Song Recording and Playback—Song Settings . . . . . . . 85
Song Settings—Basic Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Connecting to a Computer and Other MIDI Devices . . . . . . . . . . . . . . 88
Connecting to External Audio Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Connecting to External Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Connecting to External MIDI Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Connecting to a Computer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92
Appendix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Message List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
MIDI Data Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Factory Setting List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101
Voice List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Program Change List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105
Preset Performance List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
XG Voice List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
XG Drum Kit List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112
Effect Type List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114
Effect Parameter List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115
Effect Data Assign Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
MIDI Data Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
MIDI Implementation Chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
CP300 Owner’s Manual
9
Introduction
Application Index
Listening
• Listening to Demo Songs with different Voices . . . . . . . . . . . . . .“Listening to the Demo Songs” on page 23
• Listening to your recorded performance . . . . . . . . . . . . . . . . . . . . . . . . . . “Playing Back a Song” on page 49
Playing
• Selecting and playing Voices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . “Playing Voices” on page 25
• Selecting and playing Performances . . . . . . . . . . . . . . . . . . . . . . . . . . . “Selecting a Performance” on page 40
• Using different pedals. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . “Using the Pedals” on page 33
• Using multiple MIDI tone generators . . . . . . . . . . . . . . . . . . . . . . . . . “Using the Master Mode” on page 39
Changing Voices
• Viewing the list of Voices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . “Voice List” on page 103
• Viewing the list of Performances. . . . . . . . . . . . . . . . . . . . . . . . . . . . . “Preset Performance List” on page 106
• Combining Voices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . “Combining Voices—Dual” on page 29
• Playing different sounds with left and right hands
. . . . . . . . . . . . . . . . . . . . . . . . . .“Playing Different Voices with the Left and Right Hands—Split” on page 31
• Adding Variations to the Sound . . . . . . . . . . . . . . . . . . . . “Bending Notes—Pitch Bend Wheel” on page 34
“Adding a Vibrato Effect to the Sound—Modulation Wheel” on page 34
“Enhancing the Sound with Reverb and Chorus” on page 35
“Equalizer (EQ)” on page 36
Recording
• Recording your performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . “Recording Your Performance” on page 42
• Deleting recorded Songs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . “Handling Song Files” on page 81
Settings
• Making detailed settings for Voices. . . . . . . . . . . . “Detailed Settings for the Voices—Voice Edit” on page 56
• Making detailed settings for the entire CP300 “Miscellaneous CP300 Settings—Other Settings” on page 67
• Making settings for Master mode . . . . . . . . . . . . . . . . . . . . . . . . “Master Settings—Master Edit” on page 53
• Making detailed settings for MIDI . . .“Detailed Settings for MIDI Operations—MIDI Settings” on page 63
• Making detailed settings for Master Equalizer . . . . . . . . . . . . . . . . . .“Master Equalizer Settings” on page 72
Saving
• Saving the Voice settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .“Handling Performance Files” on page 76
Connecting the CP300 to other devices
• What is MIDI?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . “About MIDI” on page 63
• Connecting to multiple MIDI devices . . . . . . . . . . “Connecting to External MIDI Equipment” on page 90
• Raising the volume. . . . . . . . . . . . . . . . . . . . . . . . . “Connecting to External Audio Equipment” on page 88
• Connecting to a computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . “Connecting to a Computer” on page 92
Quick solutions
• Returning to the main display . . . . . . . . . . . . . . . . . . . . . . “Display Settings—Basic Operation” on page 15
• Resetting the default settings . . . . . “Restoring the Factory-programmed Settings of the CP300” on page 16
• About the display messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . “Message List” on page 94
• Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . “Troubleshooting” on page 98
10
CP300 Owner’s Manual
Introduction
Before Using the CP300
Power Supply Connections
1
Make sure that the instrument’s [POWER] switch on the rear panel is at the OFF
position.
POWER
POWER
OFF!!
2
3
ON
OFF
Connect the supplied power cord to the [AC INLET] jack (page 22) on the
instrument’s rear panel.
Connect the other end of the power cord to an AC outlet. Make sure your CP300
meets the voltage requirement for the country or region in which it is being used.
AC INLET jack
Power cord (included)
Using the Pedals
Connect the included pedal (FC3) to the [1 SUSTAIN] jack.
An optional FC3/FC4/FC5 foot switch or FC7 foot controller can alternately be connected to this jack. Also
an optional FC3/FC4/FC5 foot switch or FC7 foot controller can be connected to the [4 AUX] jack, and can
be assigned to control a variety of parameters on the instrument (page 33).
AC INLET
ASSIGNABLE FOOT PEDAL
3
1
2
SOFT
SUSTAIN SOSTENUTO
4
AUX
IN
MIDI
OUT
USB
THRU
ASSIGNABLE FOOT PEDAL
3
1
2
SOFT
SUSTAIN SOSTENUTO
FC3/FC4/FC5
OUTPUT
R
L
R
OUTPUT
L/MONO
R
INPUT
L/MONO
4
AUX
FC7
CP300 Owner’s Manual
11
Before Using the CP300
Introduction
Using Headphones
If you are using a set of headphones, connect them to the [PHONES] jack.
PHONES jack
CAUTION
Do not use headphones at a high volume for an extended period of time. Doing so may cause hearing loss.
n If the [SPEAKER] button is lit, this indicates that the built-in speakers sound normally when using the
headphones.
Turning the Power On
Make sure the volume setting of the CP300 and external devices are turned down to the minimum.
Press the [POWER] switch to turn the power on.
MIN
MAX
MASTER VOLUME
POWER
POWER
ON!
ON
OFF
The display located in the center of the front panel lights up.
B
A
****** PleaseWait ******
******
YAMAHA
******
D
A
B
C
Press the [POWER] switch again to turn off the power to the CP300.
The display will disappear.
CP300 Owner’s Manual
YES
C
Grand Piano 1
12
NO
NO
YES
D
Before Using the CP300
Introduction
Adjusting the Brightness of the Display
You can adjust the contrast of the display by turning the [CONTRAST] knob located to the right of the LCD.
B
A
Grand Piano 1
NO
CONTRAST
YES
EXIT
C
D
Setting the Volume
To adjust the volume, use the [MASTER VOLUME] dial located at the left of the panel. When you start
playing, re-adjust the [MASTER VOLUME] dial to the most comfortable listening level.
The level
decreases.
The level
increases.
MIN
MAX
MASTER VOLUME
Terminology
Master Volume: The volume level of the entire keyboard sound.
n The [MASTER VOLUME] dial also controls the volume of the headphones.
CP300 Owner’s Manual
13
Introduction
Playing the keyboard
Playing the Sounds
Try playing some of the realistic and dynamic CP300 sounds from the keyboard now.
When you turn the power on following the directions in “Power Supply Connections” (pages 11 and 12), the
display below appears.
B
A
Grand Piano 1
NO
C
YES
D
In this condition, you can play the keyboard and hear the sound of the selected “Grand Piano 1” Voice.
To change the Voice, press any one of the Voice group buttons located at the right of the panel.
GRAND
PIANO 1
GRAND
PIANO 2
MONO
PIANO
E. PIANO 1
E. PIANO 2
E. PIANO 3
CLAVI.
VIBES
1
ORGAN 1
2
ORGAN 2
3
HARPSI.
4
STRINGS
5
CHOIR/PAD
6
GUITAR
7
BASS
8
XG
9
10
11
12
13
14
15
16
VOICE/PERFORMANCE
Voice group buttons
Play the keyboard and enjoy the sound.
14
CP300 Owner’s Manual
Introduction
Basic Operation
In this section you’ll learn about the fundamental operations of the CP300—the use of the panel buttons and controls and
how to restore the CP300’s memory to the factory default settings.
Display Settings—Basic Operation
Each function may have many items or parameters from which you can choose. To select an item or parameter,
press one of the A [–][+] – D [–][+] buttons.
Each parameter in the display corresponds to the A [–][+] – D [–][+] buttons next to it.
B
A
GrandPiano1
Strings
Choir
E.Bass
NO
C
YES
D
Sometimes, after you’ve changed the parameter values or settings, you may want to reset them to their normal
condition. To do this, simply press the [–] button and [+] button simultaneously.
B
A
ClickVolume
NO
YES
100
C
D
n The TEMPO [DOWN][UP] buttons are the same shape as the A [–][+] – D [–][+] buttons. Parameters
corresponding to button pairs of this shape can all be reset to their default values by pressing both buttons
simultaneously.
To execute the operation, press B [+(YES)] button. To cancel the operation, press the B [– (NO)] button.
In general, when a prompt is shown on the upper right of the display, press the appropriate B [– (NO)]
[+(YES)] buttons to execute or cancel the operation.
NO: Cancel
YES: Execute
B
A
SaveToMemory Execute?-->
M-001:NewSong.MID
NO
C
YES
D
Press the [EXIT] button to exit from a function.
B
A
Main
Octave
C
Set?-->
0
NO
CONTRAST
YES
EXIT
D
CP300 Owner’s Manual
15
Basic Operation
Introduction
Restoring the Factory-programmed Settings of the CP300
The CP300 has a Factory Set function for restoring your CP300’s memory to the factory default settings.
This lets you restore the CP300’s default Voices and Performances, as well as its System and other settings.
Refer to “Factory Setting List” on page 101.
There are two ways you can restore the CP300’s memory to the factory default settings: 1) Set the “Factory Set”
parameter in the Other Settings menu, or 2) Turn the power off and turn the power on again while holding the
C7 key (rightmost key on the keyboard).
Method 1
1
Press the [OTHER SETTING] button to access the Other Settings menu.
OTHER SETTING
2
Press the [OTHER SETTING] button repeatedly or use the A [–][+] buttons to call up
“Factory Set” in the display.
B
A
FactorySet
Execute?-->
MemoryFileExcluded
NO
C
3
YES
D
Use the D [–][+] buttons to select either “Memory File Excluded” or “Memory File
Included.”
Storage memory selections:
Memory File Excluded.......................Memory files are maintained.
Memory File Included .......................Memory files are erased.
B
A
FactorySet
Execute?-->
MemoryFileExcluded
NO
C
YES
D
Indicates memory files are maintained.
B
A
FactorySet
Execute?-->
MemoryFileIncluded
C
NO
YES
D
Indicates memory files are erased.
n The “Character Code” parameter in the Song File menu does not change (page 84).
16
CP300 Owner’s Manual
Basic Operation
Press the B [+ (YES)] button to execute the job.
After the job has been completed, a “Completed” message appears and operation returns to the original
display.
Introduction
4
CAUTION
For Factory Set operations that take longer to process, you will see the message “Executing” during processing.
Do not switch the power off while this message is on the display. Turning the power off in this state may cause the
system to freeze.
Terminology
File: A file contains various data in a group. A file includes both Performance data and Song data (pages 73, 81).
Method 2
Simultaneously hold down the white key on the right end of the keyboard (C7), and press the [POWER]
switch to turn on the power to the CP300.
In this case, the Memory files saved in the storage memory are not erased.
POWER
ON
OFF
C7
If you wish to erase Memory files at this time, simultaneously hold down the rightmost white key (C7) and
black key (Bb6) together and press the [POWER] switch to turn on the power to the CP300.
POWER
ON
OFF
Bb6 C7
Terminology
Storage memory: This memory area enables you to save Performance files and recorded Songs.
CP300 Owner’s Manual
17
Introduction
Basic Instructions
Turning the Power On
Selecting and Playing a Voice
First, turn the power on and set
up the keyboard before playing.
The CP300 features an exceptionally wide variety of Preset Voices
for playing in virtually any musical style. Try searching through
the Voices to find your favorites.
• Before Using the CP300 (pages 11
and 12)
• Selecting a Voice (page 25)
Terminology
POWER
ON!
ON
OFF
Preset: Refers to data loaded to the internal memory of the CP300
before being shipped from the factory.
GRAND
PIANO 1
GRAND
PIANO 2
MONO
PIANO
E. PIANO 1
E. PIANO 2
E. PIANO 3
CLAVI.
VIBES
1
ORGAN 1
2
ORGAN 2
3
HARPSI.
4
STRINGS
5
CHOIR/PAD
6
GUITAR
7
BASS
8
XG
9
10
11
12
13
14
15
16
VOICE/PERFORMANCE
Combining Voices and Playing Them on the
Keyboard
The CP300 allows you to play several different Voices together in
a layer, or play one Voice with your left hand while you play a
different Voice (or even two layered Voices!) with your right. Try
out some of the variations and experiment with your own Voice
combinations.
• Playing Different Voices Simultaneously (page 27)
• Combining Voices—Dual (page 29)
• Playing Different Voices with the Left and Right Hands—Split
(page 31)
Create Your Own Original Voices
Once you’ve explored your favorite Voices and feel comfortable
with them, try branching out creatively and use the editing
features to make your own original Voices.
• Detailed Settings for the Voices—Voice Edit (page 56)
Connecting to a Computer and MIDI devices
• Connecting to External Audio Equipment (page 88)
• Connecting to External MIDI Equipment (page 90)
• Connecting to a Computer (page 92)
MUSIC PRODUCTION
18
CP300 Owner’s Manual
SYNTHESIZER
Introduction
Basic Instructions
Recording Your Performance and Playing It Back
Recording and playing back your performance is exceptionally easy. The
CP-300 allows you to record up to sixteen independent parts, letting you
record the left- and right-hand parts separately—and lets you build up a
complete, multi-instrument Song by recording each part one-by-one.
• Recording Your Performance (page 42)
• Other Recording Techniques (page 46)
• Handling Song Files (page 81)
• Playing Back Songs (page 49)
Terminology
On the CP300, performance data is called a “Song.” This includes
demonstration tunes and piano preset tunes.
TRACK
1
2
3-16
REC
STOP
PLAY/PAUSE
SYNCHRO START
Using the Performance Functions
The useful Performance functions enable you to store and recall the entire
CP300 settings all together. These include the Dual/Split settings, Voice
and effect parameters, MIDI transmit/receive channel settings and Master
Edit settings. If you have any original Voices you’ve created, you can save
these to a Performance as well.
• Using the Performance Functions (page 73)
• Selecting a Performance (page 40)
• Performance Parameters (page 74)
• Handling Performance Files (page 76)
PERFORMANCE
GRAND
PIANO 1
GRAND
PIANO 2
MONO
PIANO
E. PIANO 1
E. PIANO 2
E. PIANO 3
CLAVI.
VIBES
1
ORGAN 1
2
ORGAN 2
3
HARPSI.
4
STRINGS
5
CHOIR/PAD
6
GUITAR
7
BASS
8
XG
9
10
11
12
13
14
15
16
PERFORM.FILE
Using as a Master Keyboard
The Master mode of the instrument enables you to control up to four external tone
generators (or four separate instrument parts on one multi-timbral tone generator).
This effectively lets you play four different MIDI instruments at one time. Once you’ve
created your custom Master settings, you can save them to a Performance as well.
• Using the Master Mode (page 39)
ZONE 1
ZONE 2
ZONE 3
ZONE 4
MASTER
• Master Settings—Master Edit (page 53)
MASTER EDIT
CP300 Owner’s Manual
19
Control Names and Functions
Basic Operation
Control Names and Functions
Front Panel
Basic Operation
5
6
7
ZONE 1
ZONE 2
8) @
ZONE 3
ZONE 4
MASTER
4
PERFORMANCE
$
& (º ™
TRACK
TRANSPOSE
SONG SELECT
SONG FILE
1
2
3-16
REC
STOP
PLAY/PAUSE
MASTER EDIT PERFORM.FILE
MIDI OUT PANEL LOCK
SONG SETTING
DOWN
£
A
UP
POWER
ON
MIN
OFF
MAX
SONG
VOLUME
MASTER VOLUME
1
NEW SONG
9!
ZONE CONTROL
SYNCHRO START
# % ^
SONG
*
¡
TEMPO
C
2
3
PHONES
A-1
B-1
C0
D0
1 Pitch Bend wheel
E0
F0
G0
A0
(page 34)
Controls the pitch bend effect.
2 Modulation wheel
(page 34)
Controls the modulation effect.
3 [PHONES] jack
(page 12)
For turning the power on or off. The power is turned on if the
button is set to this position:
. The power is turned off if
the button is set this way:
.
5 [MASTER VOLUME] dial
Adjusts the volume of the Song playback.
20
CP300 Owner’s Manual
D1
E1
F1
G1
A1
B1
C2
D2
E2
7 [ZONE CONTROL] sliders
F2
G2
A2
B2
C3
D3
(pages 28, 39)
These four sliders adjust the output level for each Layer parts
(up to four). Turning on the [MASTER] button switches the
function assigned to the [ZONE CONTROL] sliders.
(page 39)
Turning on the [MASTER] button switches the CP300 to
function as a Master keyboard.
9 [MASTER EDIT] button
(page 53)
Enables selection of the settings for the Master mode.
) [PERFORMANCE] button
(page 40)
Switches the Performance on/off.
(page 13)
Adjusts the overall volume.
6 [SONG VOLUME] slider
C1
8 [MASTER] button
(page 12)
For connection to a pair of stereo headphones.
4 [POWER] switch
B0
(page 47)
! [PERFORM.FILE] button
(page 76)
Enables selection of Performance File settings, such as saving
and deleting Performance data, and making other settings for
Performance files.
Basic Operation
Control Names and Functions
™
¢
B
CONTRAST
NO
YES
§
¶•
GRAND
PIANO 1
GRAND
PIANO 2
MONO
PIANO
E. PIANO 1
E. PIANO 2
E. PIANO 3
CLAVI.
VIBES
1
ORGAN 1
2
ORGAN 2
3
HARPSI.
4
STRINGS
5
CHOIR/PAD
6
GUITAR
7
BASS
8
XG
9
10
11
12
13
14
15
16
VOICE EDIT
SPLIT
VARIATION
‚ ¤ ›
REVERB
CHORUS
SPEAKER
MIDI SETTING
CLICK
OTHER SETTING
MASTER EQ EDIT
fl
LOW
LO-MID
MID
HI-MID
HIGH
DEMO
EXIT
∞
D
D3
E3
F3
G3
A3
VOICE/PERFORMANCE
B3
C4
D4
E4
F4
G4
A4
@ [TRANSPOSE] button
ª
B4
⁄ ‹ fi
C5
D5
(page 37)
The Transpose function makes it possible to shift the pitch of
the entire keyboard up or down, letting you easily match the
pitch of the keyboard to the range of a singer or other
instruments.
# SONG SELECT [N][O] buttons
(pages 42, 49)
Selects a Preset Song or one of your recorded Songs.
$ TRACK [1], [2], and [3-16] buttons
(page 50)
For turning off the specified track as required so you can
practice the corresponding track (the track that is turned off )
on the keyboard.
% SONG [REC] button
(page 42)
E5
F5
MASTER EQUALIZER
G5
A5
B5
C6
D6
E6
F6
G6
A6
B6
& [SONG FILE] button
C7
(page 81)
Saves recorded Songs and makes other settings for Song files.
* [SONG SETTING] button
(page 85)
Enables selection of the settings for playback of recorded
Songs.
( [MIDI OUT] button
(page 51)
Switches MIDI transmission on/off.
º [PANEL LOCK] button
(page 51)
Switches panel lock on/off. Turning on the button disables the
panel operations.
¡ TEMPO [UP]/[DOWN] buttons
(page 38)
Adjusts the tempo.
For recording your keyboard performance.
^ SONG [PLAY/PAUSE], [STOP] buttons
(page 49)
Plays back the Preset Songs or your recorded Songs.
CP300 Owner’s Manual
21
Control Names and Functions
™ A to D [–][+] buttons
ª VARIATION [▼][▲] buttons
(page 15)
For selecting parameters and changing values while viewing
the display.
£ Display
‚ [REVERB], [CHORUS] buttons
(page 15)
For showing various messages and certain settings of the
instrument.
¢ [CONTRAST] knob
(page 35)
These add ambience (Reverb) and depth (Chorus) to the
sound. You can turn the corresponding effect on or off with a
single touch.
(page 13)
⁄ MASTER EQ EDIT [▼][▲] buttons
Adjusts the brightness of the display.
(page 72)
Enables selection of detailed settings for the Master Equalizer.
Basic Operation
∞ [EXIT] button
(page 15)
¤ [SPEAKER] button
Returns to the initial display (the display that first appears
when the power is turned on).
§ Voice group buttons
(page 25)
Enables selection of alternate Voices in the selected Voice
group.
(page 52)
Switches the built-in speakers on or off.
‹ [CLICK] button
(pages 25, 40)
These let you select from sixteen groups of Voices, including
grand piano. You can also select a Performance if the
[PERFORMANCE] button is turned on.
(page 38)
Switches the click function on or off.
› [MIDI SETTING] button
(page 64)
Enables selection of detailed MIDI settings.
¶ [VOICE EDIT] button
(page 56)
fi [OTHER SETTING] button
Enables selection of detailed settings of the sounds and effects.
• [SPLIT] button
(page 67)
This lets you make detailed settings, such as adjusting the
keyboard touch or making fine adjustments to the scale.
(page 31)
Allows you to play different Voices on the left- and right-hand
sections of the keyboard.
fl [MASTER EQUALIZER] sliders
(page 36)
These five sliders adjust the tone of each band: LOW (low
band) to HIGH (high band).
Rear Panel
AC INLET
ASSIGNABLE FOOT PEDAL
3
1
2
SOFT
SUSTAIN SOSTENUTO
1
1 [AC INLET] jack
4
AUX
2
(page 11)
Connect the supplied AC power cord here. Use only the AC
power cord supplied with the CP300.
2 [ASSIGNABLE FOOT PEDAL] jacks
(pages 11, 33)
For connecting the included pedal (FC3), an optional FC4/5
foot switch, or FC7 foot controller.
3 MIDI [IN][OUT][THRU] connectors
(page 90)
For connecting external MIDI devices, allowing the use of
various MIDI functions.
4 [USB] connector
For connecting the CP300 and computer.
22
CP300 Owner’s Manual
(page 92)
IN
MIDI
OUT
3
USB
THRU
OUTPUT
R
4
L
5
5 OUTPUT [L][R] jacks
R
OUTPUT
L/MONO
6
R
INPUT
L/MONO
7
(page 88)
These jacks output balanced audio signals, and are for
connection to an external device such as a mixer.
6 OUTPUT [L/MONO][R] jacks
(page 88)
These jacks output stereo audio signals (1/4" mono phone
plug). For monophonic output, use just the L/MONO jack.
7 INPUT [L/MONO][R] jacks
(page 89)
External audio signals can be input via these phone jacks (1/4"
mono phone plug). The sound of an external instrument can
be reproduced via the CP300’s speakers. Use 1/4" mono
phone plugs. For stereo input from an audio device, connect
to both the L/MONO and R jacks.
Quick Guide
Listening to the Demo Songs
The CP300 has a variety of specially recorded Demo Songs that effectively showcase each of the instrument’s
Voice groups. Listen to some of these Demo Songs now and hear the wide-ranging capabilities of the CP300.
TRACK
MASTER
PERFORMANCE
TRANSPOSE
SONG SELECT
1
2
3-16
REC
STOP
PLAY/PAUSE
MASTER EDIT PERFORM.FILE
SONG FILE
SONG SETTING
MIDI OUT PANEL LOCK
B
A
NO
DOWN
CONTRAST
YES
UP
GRAND
PIANO 1
GRAND
PIANO 2
MONO
PIANO
E. PIANO 1
E. PIANO 2
E. PIANO 3
CLAVI.
VIBES
1
ORGAN 1
2
ORGAN 2
3
HARPSI.
4
STRINGS
5
CHOIR/PAD
6
GUITAR
7
BASS
8
XG
9
10
11
12
13
14
15
16
VOICE EDIT
SPLIT
REVERB
VARIATION
CHORUS
MASTER EQ EDIT
SPEAKER
MIDI SETTING
CLICK
OTHER SETTING
Basic Operation
n Make sure the CP300 is ready for playback. Details are given in the section “Before Using the CP300” on page 11.
DEMO
EXIT
NEW SONG
SYNCHRO START
C
TEMPO
D
SONG
VOICE/PERFORMANCE
3
1
4
2
1
Simultaneously press both the [MIDI SETTING] button and the [OTHER SETTING]
button.
The Voice group button indicators will flash in sequence.
The “Voice Demo” message appears in the display.
A
B
VoiceDemo
SelectVoiceButton
NO
C
2
YES
D
Press one of the Voice group buttons to listen to the Demo Songs.
The corresponding Voice button indicator lights up and playback starts. Demo Songs provided for each
Voice group will play back in sequence until you press the [STOP] button.
Adjusting the Volume
To adjust the volume level of the Demo Songs, use the [MASTER VOLUME] dial or [SONG VOLUME]
slider.
ZONE 1
MIN
MAX
MASTER VOLUME
SONG
VOLUME
ZONE 2
ZONE 3
ZONE 4
ZONE CONTROL
n Make sure that the [SONG VOLUME] slider is set appropriately. If the [SONG VOLUME] slider is set to
minimum, no sound can be heard.
3
4
Press the button of the Voice group currently being played or the [PLAY/PAUSE]
button to stop the Voice demo.
Press the [EXIT] button to exit the Demo selection display.
CP300 Owner’s Manual
23
Quick Guide
Listening to the Piano Demo Songs
1
2
Simultaneously press both the [MIDI SETTING] button and the [OTHER SETTING]
button.
Use the A [–][+] buttons to select the Piano Demo Songs.
The “Piano Demo” message appears in the display.
A
B
Basic Operation
PianoDemo
SelectVoiceButton
NO
C
3
YES
D
Press one of the Voice group buttons to listen to the corresponding Piano Demo
Song.
GRAND
PIANO 1
GRAND
PIANO 2
MONO
PIANO
E. PIANO 1
E. PIANO 2
E. PIANO 3
CLAVI.
VIBES
1
ORGAN 1
2
ORGAN 2
3
HARPSI.
4
STRINGS
5
CHOIR/PAD
6
GUITAR
7
BASS
8
XG
9
10
11
12
13
14
15
16
VOICE/PERFORMANCE
The Piano Demo Songs are assigned to the sound buttons as follows.
Voice Name
24
Piano Demo Song
1
GRAND PIANO 1
Stereo sampling
Song recorded in stereo.
2
GRAND PIANO 2
Mono sampling
Song recorded with a mono sampled sound.
Showcases the Dynamic Sampling feature, with
multiple velocity-switched samples to accurately
simulate the timbral response of an acoustic
instrument.
3
MONO PIANO
Dynamic sampling: mezzopiano
4
E. PIANO 1
Dynamic sampling: mezzoforte
5
E. PIANO 2
Dynamic sampling: forte
6
E. PIANO 3
With Sustain
(with Sustain Sampling)
7
CLAVI.
No Sustain
(without Sustain Sampling)
8
VIBES
With KeyOff
(with Key-off Sampling)
9
ORGAN 1
No KeyOff
(without Key-off Sampling)
10
ORGAN 2
With String Resonance
11
HARPSI.
No String Resonance
CP300 Owner’s Manual
Description
Showcases the Sustain Sampling feature, which
reproduces the unique resonance of an acoustic
grand piano’s soundboard and strings when the
damper pedal is pressed.
Showcases the Key-off Samples that add the
subtle sound produced when the keys are
released on an acoustic piano.
Showcases the String Resonance feature that
recreates the characteristic resonance of actual
piano strings.
Quick Guide
Playing Voices
Selecting a Voice
2
1 Voice group buttons
TRACK
PERFORMANCE
TRANSPOSE
SONG SELECT
1
2
3-16
REC
STOP
PLAY/PAUSE
SONG FILE
SONG SETTING
MIDI OUT PANEL LOCK
B
A
NO
DOWN
CONTRAST
YES
UP
GRAND
PIANO 1
GRAND
PIANO 2
MONO
PIANO
E. PIANO 1
E. PIANO 2
E. PIANO 3
CLAVI.
VIBES
1
ORGAN 1
2
ORGAN 2
3
HARPSI.
4
STRINGS
5
CHOIR/PAD
6
GUITAR
7
BASS
8
XG
9
10
11
12
13
14
15
16
VOICE EDIT
SPLIT
VARIATION
REVERB
CHORUS
MASTER EQ EDIT
SPEAKER
MIDI SETTING
CLICK
OTHER SETTING
DEMO
EXIT
NEW SONG
SYNCHRO START
C
TEMPO
D
SONG
Basic Operation
MASTER
MASTER EDIT PERFORM.FILE
VOICE/PERFORMANCE
2
1
Select the desired Voice group button by pressing one of the Voice group buttons.
In this step, press the [GRAND PIANO 1] button.
n Make sure the [PERFORMANCE] button is turned off. For details about Performances, refer to page 73.
n Refer to the “Voice List” on page 103 for more information on the characteristics of each Preset Voice.
2
Select the desired Voice by using the VARIATION [▼][▲] buttons or the A [–][+]
buttons.
The currently selected Voice will sound when you play the keyboard.
Indicates the currently selected Voice
A
B
Mellow Piano 1
NO
C
Voice Group
GrandPiano1
D
Voice Name
Grand Piano 1
Voice Group
Organ1
Theater Organ
Rock Piano
Rock Organ
Grand Piano 2
Draw Organ
Organ2
Mellow Piano 2
MonoPiano
Pipe Organ Flute
Harpsichord
Comp. Piano 1
Comp. Piano 2
Strings
Synth Strings
Slow Strings
Choir/Pad
DX E.Piano 1
Scat
DX E.Piano 2
Synth Pad 1
Tremolo Vintage E.P.
Synth Pad 2
Guitar
Vintage E.Piano
Amp.Sim.Vintage E.P.
Nylon Guitar
Steel Guitar
Bass
Phaser Clavi.
Wood Bass
Bass&Cymbal
Clavi. 1
Electric Bass
Wah Clavi.
Fretless Bass
Clavi. 2
Vibraphone
Choir
Slow Choir
Synth Piano
Clavi.
Strings
Phaser E.Piano
Standard E.Piano
E.Piano3
Harpsichord 8'
Harpsichord 8'+4'
Chorus E.Piano
AutoPan E.Piano
E.Piano2
Pipe Organ Principal
Pipe Organ Tutti
Mono Piano 1
Mono Piano 2
E.Piano1
Voice Name
Jazz Organ
Mellow Piano 1
Honky Tonk Piano
GrandPiano2
YES
XG
XG Voice
Vibraphone
Marimba
Celesta
CP300 Owner’s Manual
25
Quick Guide
About XG Voices
The XG Voices are categorized and contained in appropriate folders. Select the XG Voice group first, then
select the desired Voice.
2-1
Press the [XG] button.
GRAND
PIANO 1
GRAND
PIANO 2
MONO
PIANO
E. PIANO 1
E. PIANO 2
E. PIANO 3
CLAVI.
VIBES
1
ORGAN 1
2
ORGAN 2
3
HARPSI.
4
STRINGS
5
CHOIR/PAD
6
GUITAR
7
BASS
8
XG
9
10
11
12
13
14
15
16
VOICE/PERFORMANCE
Basic Operation
2-2
Simultaneously press the [–] [+] buttons located beside the XG Voice name display,
to call up the display for selecting XG Voices.
In this case, press the A [–][+] buttons simultaneously to call up the XG Voice selection display.
Voice group name
Indicates that an XG Voice is selected
B
A
PIANO
00:GrandPiano
C
XG
NO
YES
D
Voice name
The XG Voice selection display can also be called up by pressing both the VARIATION [▼][▲]
buttons simultaneously, after pressing the [XG] button.
3
26
2-3
Use the A [–][+] buttons to select a Voice group.
2-4
Use the C [–][+] buttons to select a specific Voice.
Play the keyboard.
CP300 Owner’s Manual
Quick Guide
Playing Different Voices Simultaneously
The advanced features of the CP300 allow you to do things and perform in ways that are simply not possible
on an acoustic instrument. For example, you can play several different Voices together in a layer, or play one
Voice (or even two) layered Voices with your left hand while you play a different Voice (or two) layered Voices
with your right.
Basic Operation
You can make detailed settings for each Voice and combined Voice in Dual or Split. Refer to the “Detailed
Settings for the Voices—Voice Edit” on page 56.
Keyboard Part Combinations
The CP300 lets you effectively divide the keyboard into four independent parts: Main, Layer, Left and Left
Layer. Moreover, a different Voice can be assigned to each part.
■ Playing a Single Voice (Main part) (page 25)
You can play a single Voice over the entire keyboard range. This is used for normal performance.
Main part
■ Playing Two Voices Simultaneously (Dual) (page 29)
This lets you play a unison melody with two different instruments, or combine two similar, complementary
Voices to create a thicker sound.
Layer part
Main part
■ Playing Different Voices with Your Left and Right Hands (Split) (page 31)
This allows you to play different Voices with your left and right hands. For example, you can play a bass
part with your left hand, using the Wood Bass or Electric Bass Voice, and a melody on top with your right
hand.
Left part
Main part
■ Playing Three Different Voices with Your Left and Right Hands (Split and Dual for the
Main parts) (pages 29, 31)
Left part
Layer part
Main part
■ Playing Three Different Voices with Your Left and Right Hands (Split and Dual for the
Left parts) (page 31)
Left Layer part
Left part
Main part
■ Playing Four Different Voices with Your Left and Right Hands (Split and Dual) (page 30)
Left Layer part
Left part
Layer part
Main part
n The volume level for each Voice part can be adjusted independently. For details, refer to page 28.
CP300 Owner’s Manual
27
Quick Guide
Changing the Volume for Each Part (Zone Control)
The convenient [ZONE CONTROL] sliders allow you to adjust the volume of each part independently while
you play the keyboard. Moving a slider up increases the volume while pulling the slider down decreases it.
Layer part
Main part
Left Layer part
Left part
ZONE 1
ZONE 2
Basic Operation
SONG
VOLUME
ZONE 3
ZONE 4
ZONE CONTROL
ZONE 1: Main part
ZONE 2: Left part
ZONE 3: Layer part
ZONE 4: Left Layer part
n When you play a single Voice (Main part), you can adjust the volume by moving the [ZONE 1] slider. In this case,
the [ZONE 2], [ZONE 3] and [ZONE 4] sliders have no effect on the volume.
Turning on the [MASTER] button switches the function assigned to the [ZONE CONTROL] sliders. Refer
to the “Using the Master Mode” on page 39.
MASTER
PERFORMANCE
MASTER EDIT PERFORM.FILE
28
CP300 Owner’s Manual
Quick Guide
Combining Voices—Dual
Using Voices of Different Voice Groups—Dual
2
1, 3 Voice group buttons
2
TRACK
PERFORMANCE
TRANSPOSE
SONG SELECT
1
2
3-16
REC
STOP
PLAY/PAUSE
SONG FILE
SONG SETTING
MIDI OUT PANEL LOCK
B
A
NO
DOWN
CONTRAST
YES
UP
GRAND
PIANO 1
GRAND
PIANO 2
MONO
PIANO
E. PIANO 1
E. PIANO 2
E. PIANO 3
CLAVI.
VIBES
1
ORGAN 1
2
ORGAN 2
3
HARPSI.
4
STRINGS
5
CHOIR/PAD
6
GUITAR
7
BASS
8
XG
9
10
11
12
13
14
15
16
VOICE EDIT
SPLIT
VARIATION
REVERB
CHORUS
MASTER EQ EDIT
SPEAKER
MIDI SETTING
CLICK
OTHER SETTING
DEMO
EXIT
NEW SONG
SYNCHRO START
TEMPO
C
D
SONG
Basic Operation
MASTER
MASTER EDIT PERFORM.FILE
VOICE/PERFORMANCE
n Make sure the [PERFORMANCE] button is turned off. For details about Performances, refer to page 73.
1
Press two Voice group buttons at the same time (or press one Voice group button
while holding down another) to enable Dual.
In this step, press the [GRAND PIANO 1] button and the [CHOIR/PAD] button.
The [GRAND PIANO 1] button and [CHOIR/PAD] button light. The selected Voice name will appear
in the display.
Main part
Layer part
A
B
GrandPiano1
NO
C
2
Dual
Choir
YES
D
Select the particular Voice for each part by using the A [–][+] buttons and B [– (NO)]
[+ (YES)] buttons.
You can also select the Main part Voice by using the VARIATION [▼][▲] buttons.
n XG Voices can also be selected. For more information, refer to “About XG Voices” on page 26.
Select the “Honky Tonk Piano” Voice by using the A [–][+] buttons and select the “Scat” Voice by using
the B [– (NO)][+ (YES)] buttons.
Main part
Layer part
A
B
HonkyTonkPiano
Scat
NO
C
YES
D
To select three parts—Main, Layer and Left—simultaneously hold down the [SPLIT] button and press
the desired Voice group button.
Main part
Layer part
A
B
GrandPiano1
Strings
C
Split + Dual for the Main parts
Choir
NO
YES
D
Left part
CP300 Owner’s Manual
29
Quick Guide
To select four parts—Main, Layer, Left and Left Layer—simultaneously hold down the [SPLIT] button
and press two Voice group buttons.
Main part
Layer part
B
A
GrandPiano1
Strings
Choir
E.Bass
Split + Dual
NO
C
YES
D
Left part
Left Layer part
You can select other Voices by using the A – D letter buttons (A [–][+] to D [–][+]).
Basic Operation
n For details about the Split function, refer to page 31.
3
Press any single Voice group button to exit Dual and return to normal play.
Using Voices in the Same Voice Group—Dual
Dual can also be used to select and play Voices in the same Voice group.
1
2
3
30
Press one of the Voice group buttons.
Use the A [–][+] buttons to select the desired Voice.
You can also select the Main part Voice by pressing the VARIATION [▼][▲] buttons.
Use the B [– (NO)][+ (YES)] buttons to select another Voice in the same Voice group.
To use identical Voices, press the B [– (NO)][+ (YES)] buttons once.
To use different Voices within the same Voice group, press the B [– (NO)][+ (YES)] buttons repeatedly.
CP300 Owner’s Manual
Quick Guide
Playing Different Voices with the Left and Right Hands—Split
2
2, 3
TRACK
PERFORMANCE
TRANSPOSE
SONG SELECT
1
2
3-16
REC
STOP
PLAY/PAUSE
SONG FILE
SONG SETTING
MIDI OUT PANEL LOCK
B
A
NO
DOWN
CONTRAST
YES
UP
GRAND
PIANO 1
GRAND
PIANO 2
MONO
PIANO
E. PIANO 1
E. PIANO 2
E. PIANO 3
CLAVI.
VIBES
1
ORGAN 1
2
ORGAN 2
3
HARPSI.
4
STRINGS
5
CHOIR/PAD
6
GUITAR
7
BASS
8
XG
9
10
11
12
13
14
15
16
VOICE EDIT
SPLIT
VARIATION
REVERB
CHORUS
MASTER EQ EDIT
SPEAKER
MIDI SETTING
CLICK
OTHER SETTING
DEMO
EXIT
NEW SONG
SYNCHRO START
TEMPO
C
D
SONG
VOICE/PERFORMANCE
4
3
1
2
3
Basic Operation
MASTER
MASTER EDIT PERFORM.FILE
1,4,5 [SPLIT] button
Press the [SPLIT] button to enable Split.
The [SPLIT] button lights.
Select a Voice for the right-hand area by pressing one of the Voice group buttons.
In this step, press the [GRAND PIANO 1] button.
Use the A [–][+] buttons to select the “Honky Tonk Piano” Voice.
Select a Voice for the left-hand area by simultaneously holding down the [SPLIT]
button and pressing one of the Voice group buttons.
In this step, press the [CHOIR/PAD] button.
Use the C [–][+] buttons to select the “Scat” Voice.
Main part
A
B
Split
HonkyTonkPiano
Scat
NO
C
YES
D
Left part
To divide the keyboard into Main, Layer and Left parts, press two Voice group buttons at the same time
(or press one Voice group button while holding down another).
Main part
Layer part
A
B
GrandPiano1
Strings
Split + Dual for the Main parts
Choir
NO
C
YES
D
Left part
To divide the keyboard into Main, Layer and Left Layer parts, simultaneously hold down the [SPLIT]
button and press two Voice group buttons.
Main part
A
B
Grand Piano 1
Strings
NO
Split + Dual for the Left parts
YES
E.Bass
C
D
Left part
Left Layer part
To divide the keyboard into four parts—Main, Layer, Left and Left Layer—perform both the above
operations (last two sentences) in order.
CP300 Owner’s Manual
31
Quick Guide
4
Specify the split point (the border between the right- and left-hand range).
The default setting (factory setting) is “F#2.” (If you do not need to change the split point, skip this
step.)
F#2
Center “C” (C3)
Basic Operation
To Change the Split Point Setting
4-1
Simultaneously hold down the [SPLIT] button and use the D [–][+] buttons to specify
the split point.
There is also a quicker, more intuitive way: instead of using the D [–][+] buttons, simultaneously hold
down the [SPLIT] button and press the appropriate key on the keyboard.
A
B
SplitPoint
NO
YES
F#2
C
D
Split point
n The Main part and Layer part of the split point are specified simultaneously. If you wish to independently change
the split point for each part, you can call up the Other Settings menu and use the “Split Point” parameter to set the
Main part split point and use “Split Point 2” to set that of the Layer part (page 69).
4-2
5
32
Release the [SPLIT] button to return to the main display.
Press the [SPLIT] button to exit Split and return to normal play.
CP300 Owner’s Manual
Quick Guide
Using the Pedals
ASSIGNABLE FOOT PEDAL
3
1
2
SOFT
SUSTAIN SOSTENUTO
4
AUX
IN
MIDI
OUT
USB
THRU
ASSIGNABLE FOOT PEDAL
3
1
2
SOFT
SUSTAIN SOSTENUTO
FC3/FC4/FC5
OUTPUT
R
L
R
OUTPUT
L/MONO
R
INPUT
L/MONO
4
AUX
Basic Operation
AC INLET
FC7
CAUTION
Make sure that the power is off when connecting or disconnecting any pedal.
n • By connecting a pedal to the [ASSIGNABLE FOOT PEDAL] jack, you can use the pedal to control one of various
assignable functions. Refer to the “Pedal 1/Pedal 2/Pedal 3/Pedal 4” parameter in the Voice Edit menu (pages 61, 62).
• Depending upon the pedal that is connected to the [ASSIGNABLE FOOT PEDAL] connector, the effect produced by
operating the pedal (on/off, dynamics, etc.) might be reversed. Refer to the “Pedal Type” parameter in the Other
Settings menu (page 70).
• The function of the [PLAY/PAUSE] button can be assigned to the pedal connected to the [2 SOSTENUTO]/[3
SOFT]/[4 AUX] jacks. Refer to the “Pedal Play/Pause” parameter in the Other Settings menu (page 70).
The [ASSIGNABLE FOOT PEDAL] jack is set initially for use with the following functions (factory default
setting).
Sustain Pedal (1 SUSTAIN jack)
This jack is for connecting the included FC3 foot pedal. The pedal functions in the same way as a damper pedal on
an acoustic piano. Connect the included pedal (FC3) to this jack and press the pedal to sustain the sound.
When Voices of the GRAND PIANO 1 Voice group and the Mono Piano 1 and Comp. Piano 1 Voices are selected,
pressing the FC3 pedal activates the instrument’s special Sustain Samples, which accurately recreate the unique
resonance of an acoustic grand piano’s soundboard and strings. The FC3 can also be used to control the half pedal
effect on these Voices, recreating the partial damping of strings that is possible on an actual piano. An optional FC4/
FC5 foot switch can also be connected to this jack. However, these foot switches cannot be used to control the half
pedal effect.
n The depth of the effect produced by the Sustain Samples can be adjusted via the “Sustain Sampling Depth”
parameter in the Other Settings menu (page 69).
Sostenuto Pedal (2 SOSTENUTO jack)
This jack is for connecting an included foot pedal FC3 and an optional FC3/FC4/FC5 foot switch.
If you play a note or chord on the keyboard and press the sostenuto pedal while holding the note(s), the notes will
sustain as long as the pedal is held. This makes it possible to sustain a chord, for example, while other notes are
played “staccato.”
n Organ, string and choir Voices will continue to sound for as long as the sostenuto pedal is depressed.
Soft Pedal (3 SOFT jack)
This jack is for connecting an included foot pedal FC3 and an optional FC3/FC4/FC5 foot switch. The soft pedal
reduces the volume and slightly changes the timbre of notes played while the pedal is pressed. The soft pedal will not
affect notes that are already playing.
n The depth of the Soft pedal can be adjusted via the “Soft Pedal Depth” parameter in the Other Settings menu
(page 69).
AUX Pedal (4 AUX jack)
This jack is for connecting an optional FC7 foot controller.
This AUX Pedal can be assigned to control a variety of parameters on the instrument. Refer to the “Pedal 4"
parameter in the Voice Edit menu (page 62).
CP300 Owner’s Manual
33
Quick Guide
Bending Notes—Pitch Bend Wheel
Use the Pitch Bend wheel to bend notes up (roll the wheel away from you) or down (roll the wheel toward you)
while playing the keyboard. This wheel is self-centering and will automatically return to normal pitch when
released. Try out the Pitch Bend wheel while pressing a note on the keyboard.
Raises the pitch
Basic Operation
Lowers the pitch
Pitch Bend wheel
n The bend range can be adjusted via the “Pitch Bend Range” parameter in the Other Settings menu (page 70).
Adding a Vibrato Effect to the Sound—Modulation Wheel
The Modulation wheel applies vibrato to the sound. The more you move this wheel up, the greater the effect
that is applied to the sound. Try out the Modulation wheel with various Preset Voices while playing the
keyboard.
Maximum
Minimum
Modulation wheel
n Keep in mind that many of the Preset Voices are not set with a Modulation effect. (This is to ensure the most
natural sound on these acoustic instrument Voices.) However, the Modulation wheel can be effectively used to
control user-programmable effects, as well as alter the sounds of a connected MIDI tone generator.
n Various functions can be assigned to the Modulation Wheel. Refer to the “Modulation” parameter in the Voice
Edit menu (page 62).
n To avoid accidentally applying Modulation or other effects to the current Voice, make sure the Modulation Wheel
is set to minimum before you start playing.
34
CP300 Owner’s Manual
Quick Guide
Enhancing the Sound with Reverb and Chorus
The effect processing of the CP300 features both System Effects and Insertion Effects.
System Effects—Reverb and Chorus
System Effects are applied to the overall sound, whether it be a Voice, an entire Performance, a Song, etc. Each
part can be given a different amount of System Effect processing.
Basic Operation
[REVERB] button
[CHORUS] button
TRACK
MASTER
PERFORMANCE
TRANSPOSE
SONG SELECT
1
2
3-16
REC
STOP
PLAY/PAUSE
MASTER EDIT PERFORM.FILE
SONG FILE
SONG SETTING
MIDI OUT PANEL LOCK
B
A
NO
DOWN
CONTRAST
YES
UP
GRAND
PIANO 1
GRAND
PIANO 2
MONO
PIANO
E. PIANO 1
E. PIANO 2
E. PIANO 3
CLAVI.
VIBES
1
ORGAN 1
2
ORGAN 2
3
HARPSI.
4
STRINGS
5
CHOIR/PAD
6
GUITAR
7
BASS
8
XG
9
10
11
12
13
14
15
16
VOICE EDIT
SPLIT
VARIATION
REVERB
CHORUS
MASTER EQ EDIT
SPEAKER
MIDI SETTING
CLICK
OTHER SETTING
DEMO
EXIT
NEW SONG
SYNCHRO START
TEMPO
C
D
SONG
VOICE/PERFORMANCE
Reverb
The reverb effects add a warm ambience to the sound, simulating the complex reflections of actual
performance spaces, such as a concert hall or small club.
Refer to “Effect Type List” on page 114 for more information on the preset reverb types.
Pressing the [REVERB] button alternates between On and Off.
The indicator lights if reverb is turned on.
n You can select a reverb type via the “Reverb Type” parameter in the Voice Edit menu, and adjust the reverb depth
for the selected Voice via the “Reverb Send” parameter (page 58).
n Even if the reverb effect is turned off, a “soundboard reverb” effect will be applied for these Voices: GRAND
PIANO 1, GRAND PIANO 2 Voice groups and Mono Piano 1, Mono Piano 2, Marimba and Celesta Voices.
Chorus
The chorus effects use various types of modulation processing, including flanger and phaser, to enhance the
sound in a variety of ways.
Refer to “Effect Type List” on page 114 for more information on the preset chorus types.
Pressing the [CHORUS] button alternates between On and Off.
The indicator lights if chorus is turned on.
You can turn the chorus effect on and off by pressing the [CHORUS] button on the panel and by setting the
“Chorus On Off ” parameter in the Voice Edit menu (page 59). The [CHORUS] button setting on the panel is
temporary. That is, if you select another Voice, the chorus setting for the previous Voice is cancelled.
The “Chorus On Off ” parameter setting is saved for each Voice. That is, if you select a given Voice, the chorus
setting is automatically turned on or off according to the saved chorus setting.
n You can select a chorus type via the “Chorus Type” parameter in the Voice Edit menu and adjust the chorus depth
for the selected Voice via the “Chorus Send” parameter (page 59). You can also turn chorus on or off via the
“Chorus On Off ” parameter (page 59).
Insertion Effects
Insertion effects can be applied individually to each part. Insertion effects are mainly used to directly process a
single part. The CP300 has three separate Insertion Effect blocks, letting you apply different effects on up to
three parts from Main, Layer, Left and Left Layer parts (page 27).
n You can select an Insertion type via the “Ins. Type” parameter in the Voice Edit menu, and adjust the Insertion
effect depth for the selected part via the “Dry/Wet Balance” parameter (pages 59, 60).
The CP300 also has a Variation effect that can be used as either a System effect or Insertion effect. Refer to
“Effect Type List” on page 114 for more information on the types of effects you can use. The Variation effect
can be controlled only by the use of MIDI messages.
CP300 Owner’s Manual
35
Quick Guide
Equalizer (EQ)
Usually an equalizer is used to correct the sound output from amps or speakers to match the special character
of the room, or to change the tonal character of the sound. EQ divides the sound into several frequency bands,
and adjustments are made by raising or lowering the level of each band.
By adjusting the sound according to the genre—classical music being more refined, pop music more crisp, and
rock music more dynamic—you can draw out the special characteristics of the music and make your
performance more enjoyable.
Two separate EQ sections are available on the instrument: Part EQ and Master EQ.
Basic Operation
Part EQ
The Part EQ is applied to each Voice.
Gain
Low Gain
High Gain
Freq.
Low Freq.
High Freq.
n You can adjust the part’s low and high frequency via the “EQ Low Freq.” and “EQ High Freq.” parameter in the
Voice Edit menu. You can also adjust the part’s low- and high-range gain via the “EQ Low Gain” and “EQ High
Gain” parameters (pages 60, 61).
Master EQ
Master EQ is applied to the final, overall (post-effect) sound of the instrument.
When the corresponding slider is set to center, the equalizer level is set to normal.
Q (frequency bandwidth)
Gain
+
0
Freq.
–
5 bands
LOW LOWMID MID HIGHMID HIGH
n You can adjust the Q (frequency bandwidth) and Frequency parameters via the Master EQ Edit menu (page 72).
However, the last gain setting by the slider or Master EQ Edit menu will remain in effect.
n While the “Equalizer Lock” parameter (page 71) in the Other Settings menu is turned on, the Master Equalizer
values will not be affected by Performance recall, incoming MIDI data and Song playback.
36
CP300 Owner’s Manual
Quick Guide
Key Transposition—Transpose
The CP300’s Transpose function makes it possible to shift the pitch of the entire keyboard up or down in
semitone intervals to facilitate playing in difficult key signatures, and to let you easily match the pitch of the
keyboard to the range of a singer or other instruments. For example, if you set the transposition amount to
“+5,” playing a C key produces a pitch of F. In this way, you can play a Song as though it were in C major, and
the CP300 will transpose it to the key of F.
Basic Operation
Press the [TRANSPOSE] button to transpose the entire keyboard. With just the press of a button, you can
reconfigure the transpose setting. For details about setting the amount of transposition, see below. The
indicator will light when a transpose setting other than “0” is selected.
1 [TRANSPOSE] button
TRACK
MASTER
PERFORMANCE
TRANSPOSE
SONG SELECT
1
2
3-16
REC
STOP
PLAY/PAUSE
MASTER EDIT PERFORM.FILE
SONG FILE
SONG SETTING
MIDI OUT PANEL LOCK
B
A
NO
DOWN
CONTRAST
YES
UP
GRAND
PIANO 1
GRAND
PIANO 2
MONO
PIANO
E. PIANO 1
E. PIANO 2
E. PIANO 3
CLAVI.
VIBES
1
ORGAN 1
2
ORGAN 2
3
HARPSI.
4
STRINGS
5
CHOIR/PAD
6
GUITAR
7
BASS
8
XG
9
10
11
12
13
14
15
16
VOICE EDIT
SPLIT
VARIATION
REVERB
CHORUS
MASTER EQ EDIT
SPEAKER
MIDI SETTING
CLICK
OTHER SETTING
DEMO
EXIT
NEW SONG
SYNCHRO START
TEMPO
C
D
SONG
VOICE/PERFORMANCE
2
1
3
Press the [TRANSPOSE] button.
The amount of transposition in semitone units appears in the display.
A
B
Transpose
Keyboard
NO
YES
0
C
D
Amount of transposition
2
Press the D [–][+] button to transpose down or up as required.
You can set the range from -12 semitones (down one octave) to 12 semitones (up one octave) in semitone
steps.
Transposing shifts the pitch of the entire keyboard.
The transposition range:
-12: -12 semitones (down one octave), 0: normal pitch, 12: 12 semitones (up one octave)
n You can set the keyboard’s Transpose via the “Transpose” parameter in the Other Settings menu, when the
[TRANSPOSE] button is turned on (page 69).
n The Transpose setting affects transmitted MIDI data.
3
Press the [EXIT] button to exit the Transpose setting.
n The edited Transpose settings will be erased after you turn off the power to the CP300. If you set the Memory
Backup’s Transpose setting to On in the Other Settings menu, the current Transpose setting will remain in effect
when you turn the power off and back on again (page 71).
CP300 Owner’s Manual
37
Quick Guide
Using the Click
Pressing the [CLICK] button turns Click or the metronome sound on and off.
TRACK
MASTER
PERFORMANCE
TRANSPOSE
SONG SELECT
1
2
3-16
REC
STOP
PLAY/PAUSE
MASTER EDIT PERFORM.FILE
SONG FILE
SONG SETTING
MIDI OUT PANEL LOCK
B
A
NO
DOWN
CONTRAST
YES
UP
GRAND
PIANO 1
GRAND
PIANO 2
MONO
PIANO
E. PIANO 1
E. PIANO 2
E. PIANO 3
CLAVI.
VIBES
1
ORGAN 1
2
ORGAN 2
3
HARPSI.
4
STRINGS
5
CHOIR/PAD
6
GUITAR
7
BASS
8
XG
9
10
11
12
13
14
15
16
VOICE EDIT
SPLIT
REVERB
VARIATION
CHORUS
MASTER EQ EDIT
SPEAKER
MIDI SETTING
CLICK
OTHER SETTING
DEMO
EXIT
NEW SONG
SYNCHRO START
TEMPO
C
D
SONG
VOICE/PERFORMANCE
1, 2
TEMPO [DOWN][UP] button
Basic Operation
1
Press the [CLICK] button to start the click.
Adjusting the Tempo
1-1
Press the TEMPO [DOWN] or [UP] button.
The “Tempo” parameter will appear in the display.
A
B
Tempo
NO
YES
120
C
D
Tempo
To adjust the tempo (number of beats per minute: 10-500), use the TEMPO [DOWN][UP] or the
D [–][+] buttons.
To reset the tempo to the default setting, press the TEMPO [DOWN][UP] or the D [–][+] buttons
simultaneously.
Default setting: 120 (If a Song has been selected, the Song tempo is used.)
1-2
2
Press the [EXIT] button to go back to the Main display.
Press the [CLICK] button to stop the click sound.
n You can change the time signature, volume, and bell on/off settings using the Song Setting menu (page 87).
n The click will not start after the Song is stopped. If you wish to start the click, press the [CLICK] button again.
n The click will stop when Song playback is paused.
38
CP300 Owner’s Manual
Using the Master Mode
The Master mode allows you to divide the keyboard into a total of four independent areas (called “Zones”). Each Zone can be
assigned to different MIDI channels and have different Control Slider functions. This makes it possible to control up to four
tone generators simultaneously from a single keyboard, and to control Voices of an external tone generator over several
different channels, in addition to the internal Voices of the CP300 itself.
Press the [MASTER] button to turn the Master mode on.
Turning on the Master mode also enables the “Master Edit” settings for this function.
For details, refer to page 53.
PERFORMANCE
Basic Operation
MASTER
MASTER EDIT PERFORM.FILE
Example: Connecting to external tone generators
External tone generator
Voice
Voice
ZONE 4
ZONE 2
MIDI CH4
MIDI CH2
MIDI CH3
ZONE 3
ZONE 1
MIDI CH1
External MIDI synthesizer/tone generator
ZONE 1
ZONE 1: Main part
ZONE 2: Left part
ZONE 3: Layer part
ZONE 4: Left Layer part
Left Layer part
(ZONE 4)
Left part
(ZONE 2)
Internal tone generator
ZONE 2
ZONE 3
ZONE 4
ZONE CONTROL
Layer part
(ZONE 3)
Main part
(ZONE 1)
n While the Master mode is turned on, the “MIDI Out Channel” parameter in the Master Edit menu will be
enabled for MIDI channel assignments.
n If you turn the power off and on again while the Master mode is on, the function will be turned off.
CP300 Owner’s Manual
39
Selecting a Performance
All settings of the entire CP300 can be saved together in a group, referred to as a “Performance.” A Performance includes
Dual/Split settings, Voice and effect parameters, MIDI transmit/receive channel settings and Master Edit settings. For details
on Performance settings, refer to page 73.
A total of 64 Preset Performances are supplied with the CP300. The Preset Performances consist of 32 Yamaha original Voices
and 32 default Performances (Grand Piano Voices). Try some of the Preset Performances and listen to the sound.
Terminology
Preset Performance file: A single file that includes data of 64 different Preset Performances.
Basic Operation
n Refer to the “Preset Performance List” on page 106 for more information on the characteristics of each Preset Performance.
1, 5
2
2
TRACK
MASTER
PERFORMANCE
TRANSPOSE
SONG SELECT
1
2
3-16
REC
STOP
PLAY/PAUSE
MASTER EDIT PERFORM.FILE
SONG FILE
SONG SETTING
MIDI OUT PANEL LOCK
B
A
NO
DOWN
CONTRAST
YES
UP
GRAND
PIANO 1
GRAND
PIANO 2
MONO
PIANO
E. PIANO 1
E. PIANO 2
E. PIANO 3
CLAVI.
VIBES
1
ORGAN 1
2
ORGAN 2
3
HARPSI.
4
STRINGS
5
CHOIR/PAD
6
GUITAR
7
BASS
8
XG
9
10
11
12
13
14
15
16
VOICE EDIT
SPLIT
VARIATION
REVERB
CHORUS
MASTER EQ EDIT
SPEAKER
MIDI SETTING
CLICK
OTHER SETTING
DEMO
EXIT
NEW SONG
SYNCHRO START
TEMPO
C
D
SONG
VOICE/PERFORMANCE
3
1
2
Press the [PERFORMANCE] button to enter the Performance mode.
The [PERFORMANCE] button flashes.
Choose a Performance by pressing one of the Voice group buttons.
Playing the keyboard sounds the Performance indicated in the display. The parameters shown in the
Performance Play display are briefly explained below.
A01.Piano+Pad
Hold this down to view
all Voices of the parts
Hold this down to view
the Performance file name
Performance name
Number
(Select the number by pressing
one of the Voice group buttons.)
A to D
(Select “A” to “D” by pressing the
VARIATION [▼][▲] buttons.)
A
B
A01.Piano+Pad
GrandPiano1
NO
YES
WarmPad
C
D
Voice names (Main and Layer only)
3
4
5
40
Press the VARIATION [▼][▲] buttons to select one of the Performance variations,
A to D.
A single Performance can include up to four different Performances (A to D). “A” and “B” features the
Yamaha original Voices. “C” and “D” contains the default Performances (Grand Piano Voices).
Play the keyboard.
Press the [PERFORMANCE] button to exit the Performance Play mode.
The [PERFORMANCE] button lamp turns off. The Voice selection will return to the Voice selected
before entering the Performance.
You can exit the Performance yet keep the current Voice used in the Performance by simultaneously
holding down the B [– (NO)] button and pressing the [PERFORMANCE] button.
CP300 Owner’s Manual
Recording Your Performance
This chapter explains how to record your performance using the CP300’s versatile recording features. For example, you can
record just the left-hand part, and then practice the right-hand part while playing back the recorded left-hand part. Since the
CP300 lets you record up to sixteen tracks separately, you can build up a complete, multi-instrument Song by recording each
part one-by-one.
About the Recording Features of the CP300
Basic Operation
Unlike conventional audio recording (such as to an MD recorder or cassette tape recorder), the CP300 records
your keyboard playing as performance data. In other words, while an MD records the actual sounds, the
CP300 records the physical “moves” and settings that create the sound—including which notes are played, the
timing they were played with, the Voice(s) used, and the tempo value. This type of recording has the advantage
of allowing you greater editing flexibility and smaller data size.
n If you want to record the sounds of your performance as audio data, you can do so by connecting an MD recorder
or other recording device to the [OUTPUT] connector (page 88).
Song
On the CP300, performance data is called a “Song.” This includes demonstration tunes and preset tunes.
Song (performance data)
Demo Songs
Preset Songs
Recorded
Songs
CP300 Owner’s Manual
41
Recording Your Performance
Recording Your Performance
3
2
TRACK
MASTER
PERFORMANCE
TRANSPOSE
SONG SELECT
1
2
3-16
REC
STOP
PLAY/PAUSE
MASTER EDIT PERFORM.FILE
SONG FILE
SONG SETTING
MIDI OUT PANEL LOCK
B
A
NO
DOWN
CONTRAST
YES
UP
GRAND
PIANO 1
GRAND
PIANO 2
MONO
PIANO
E. PIANO 1
E. PIANO 2
E. PIANO 3
CLAVI.
VIBES
1
ORGAN 1
2
ORGAN 2
3
HARPSI.
4
STRINGS
5
CHOIR/PAD
6
GUITAR
7
BASS
8
XG
9
10
11
12
13
14
15
16
VOICE EDIT
SPLIT
VARIATION
REVERB
CHORUS
MASTER EQ EDIT
SPEAKER
MIDI SETTING
CLICK
OTHER SETTING
DEMO
EXIT
NEW SONG
SYNCHRO START
C
TEMPO
D
SONG
VOICE/PERFORMANCE
1 3 5 4,6
Basic Operation
n The Performance mode is automatically turned off if the CP300 is set to recording or recording standby while
Performance mode is on.
1
Press the SONG SELECT [N] button and [O] button at the same time.
Indicates the current measure.
(The words “bar” and “measure” are used interchangeably.)
A
B
PresetSong
P-000:NewSong
Bar 001
NO
C
YES
D
n “P-000: New Song” is a blank Song provided for you to record your performance.
2
Select a Voice (page 25).
In addition to selecting the desired Voice, make sure to set other sound-related parameters, such as reverb
and chorus. When you’ve finished making the settings, press the SONG SELECT [N] or [O] button
to return to the “New Song” display.
Using the Click Sound
You can record data while using the Click sound. Press the [CLICK] button in Step 2.
The Click sound is not recorded.
n Refer to page 48 for more information on recording in Dual/Split mode.
3
Select a recording track.
Recording to Track 1:
Press the TRACK [1] button while holding down the [REC] button.
Recording to Track 2:
Press the TRACK [2] button while holding down the [REC] button.
Recording to Tracks 3 – 16:
Press the B [– (NO)][+ (YES)] button while holding down the [REC] button, then select the desired
recording track, 3 – 16. Keep holding down the [REC] button and press the TRACK [3-16] button.
42
CP300 Owner’s Manual
Recording Your Performance
When the recording track has been selected, the indicator for the [REC] button and selected track lights
up in red. (Record Ready mode can be disengaged before recording by pressing the [REC] button again.)
A
B
SongRecording
P-000:NewSong
Bar 001
NO
C
YES
D
4
Basic Operation
Set the Tempo, if necessary (page 38).
If this Record Standby display does not appear, press one of the SONG SELECT [N][O] buttons
once. If you select “Key On” as the Starting method (page 44), a Tempo setting of 120 will be entered at
the beginning of the Song.
Start recording.
You can start recording by pressing the [PLAY/PAUSE] button, or have recording started automatically
for you as soon as you play a note on the keyboard. The current measure number is shown in the display
during recording.
n Song recording can be paused by pressing the [PLAY/PAUSE] button. Recording will begin automatically as soon
as you play a note on the keyboard or press the [PLAY/PAUSE] button again.
5
6
Press either [STOP] button or [REC] button to stop recording.
Press the [STOP] button to return to the top of the Song.
Press the [PLAY/PAUSE] button to play back the recording.
n To erase recorded data from a track, use the “Channel Clear” parameter in the Song Setting menu for Song
playback/recording (page 86).
7
Save the recorded Song
When pressing the SONG SELECT [N][O] button, A [–][+] button or C [–][+] button, a “Song
Changed Save?” message appears in the display. Press the B [+ (YES)] button to save the file. If you want
to cancel the Save operation, press the B [– (NO)] button. For details about saving Song files, refer to
page 82.
A
B
SongChanged Save?
NO
C
YES
D
CP300 Owner’s Manual
43
Recording Your Performance
Re-recording Parts of a Song
This section explains how to record a specific section or part of a Song again.
1
Use the B [– (NO)][+ (YES)] buttons while the playback display is displayed to move
through the measures, or play back the recording and press the [PLAY/PAUSE]
button to locate a point slightly prior to the beginning of the part you wish to rerecord.
If the playback display does not appear, press one of the SONG SELECT [N][O] buttons once.
Basic Operation
Indicates the current measure.
(The words “bar” and “measure” are used interchangeably.)
A
B
PresetSong
P-000:NewSong
Bar 012
NO
C
2
3
YES
D
Select a Voice or Voices for recording, if necessary.
Repeat Step 2 on page 42 if you wish to change the previous settings.
Press and hold down the [REC] button, and press one of the C [–][+] buttons
repeatedly to specify how the recording should start. Similarly, use the D [–][+]
buttons to specify how the recording should end.
While you are holding down the [REC] button, the following recording method select display appears.
A
B
RecMode
ExtraTrackCh=3
Start:Norm
End:Replace
C
NO
YES
D
Starting methods:
Norm: All existing data in the Song will be erased after re-recording starts.
Key On: Data that exists prior to the point where you start playing a note will not be erased (when rerecording part of the Song).
Ending methods:
Replace: Existing data following the point at which you stopped recording will be erased.
Punch Out: Existing data following the point at which you stopped recording will remain.
4
44
Select a recording track, then start recording.
After this, follow the procedure beginning with Step 3 on page 42.
CP300 Owner’s Manual
Recording Your Performance
Data Recorded to User Songs
Basic Operation
Data recorded to individual tracks:
• Notes played
• Voice selection
• Pitch Bend
• Pedal/Modulation wheel ON/OFF
• Reverb depth (Reverb Send)
• Chorus depth (Chorus Send)
• Insertion effect depth (Dry/Wet Balance)
• Sound brightness (Brightness)
• Resonance effect setting (Harmonic Content)
• Equalizer’s low-range frequency setting (EQ Low Freq.)
• Equalizer’s low-range gain setting (EQ Low Gain)
• Equalizer’s high-range frequency setting (EQ High Freq.)
• Equalizer’s high-range gain setting (EQ High Gain)
• Voice octave setting (Octave)
• Voice volume level (Volume)
• Stereo image of each Voice (Pan)
• Fine tuning of the pitch of two Voices in Dual mode (Detune)
• Volume level changes for each Voice with response to the way you play (Touch Sense)
• Voice Transpose (Transpose)
• Scale (Scale)
• Depth of Soft pedal effect (Soft Pedal Depth)
• Depth of string resonance (String Resonance Depth)
• Depth of sustain sampling (Sustain Sampling Depth)
• Volume of the key-off sound (Key-off Sampling Depth)
• Modulation (Modulation)
• Pitch Bend range (Pitch Bend Range)
Data recorded globally to all tracks:
• Tempo
• Time signature (beat)
• Reverb type
• Chorus type
• Insertion effect type
n You can change any of the settings with the exception of note data (including the Octave and Transpose setting)
after recording.
n You can change the time signature at the beginning of the Song, or at a specific position in the Song, by using the
B [– (NO)][+ (YES)] buttons while the Song is stopped.
n When you record in the Dual or Split mode, the CP300 records each Voice onto a separate track. For details, refer
to page 48.
CP300 Owner’s Manual
45
Recording Your Performance
Other Recording Techniques
Adding Data to or Recording Over an Existing Song
The previous section explains how to record your performance from the beginning by selecting a blank Song
(P-000: New Song). You can also add new performance recordings to existing Songs, or overwrite your
previously recorded performances.
Basic Operation
1
Press one of the SONG SELECT [N][O] button then use the A [–][+] button to call
up “Memory Song.”
A
B
MemorySong
Bar 001
M-001:NewSong.MID
NO
C
2
YES
D
Press the C [–][+] button to select the Song you wish to add data to or record over.
You cannot add data to or record over Preset Songs.
To continue recording, follow the procedure described in “Recording Your Performance” on page 42. To add
data to an existing Song, follow the procedure starting with Step 1 in “Re-recording Parts of a Song” on
page 44.
CAUTION
If you record on a track that already has data, the existing data on the track will be lost.
Changing a Voice or Tempo After Recording
You can change the Voice or tempo after recording to change a Song’s feel or to set a more suitable tempo. You
can also change these elements in the middle of a Song.
n Before changing the Voice or tempo, set the starting method to “Norm” (page 44). When the starting method is set
to “Key On,” you cannot change the Voice or tempo.
1
2
46
Select a Song you wish to change.
To select a Song, follow the procedure described in “Adding Data to or Recording Over an Existing
Song” above.
To change the Voice or tempo in the middle of the Song, specify the measure at which
the change is to be made by using the B [– (NO)][+ (YES)] buttons while the playback
display is appeared, or by pressing the [PLAY/PAUSE] button to locate a point slightly
prior to the beginning of the part you wish to re-record.
If the playback display does not appear, press one of the SONG SELECT [N][O] buttons once.
CP300 Owner’s Manual
Recording Your Performance
3
Change the settings (Voice, reverb, etc.).
For example, if you wish to change the recorded E. Piano 1 Voice to E. Piano 2, use the Voice group
buttons and the A [–][+] buttons to select E. Piano 2.
When you’ve finished making the settings, press one of the SONG SELECT [N][O] button to
return to the Song Select display.
CAUTION
4
Basic Operation
The panel settings made in Step 3 will be saved in memory and you will not be able to restore the previous
settings. Proceed with caution.
Simultaneously hold down the [REC] button and select a track to change the value.
The indicator for the selected part lights up in red. Change the tempo setting now, if necessary.
CAUTION
Do not play the keyboard or press the [PLAY/PAUSE] button. Doing so will start recording, erasing the recorded
data.
5
Press the [STOP] or [REC] button to exit the record mode.
When you exit the record mode, the display prompts you whether you want to overwrite the Song or
not. Press the B [+ (YES)] button to overwrite the Song.
n Refer to “Data Recorded to User Songs” on page 45 for information on the settings that can be changed here.
Adjusting the Volume Balance between the Song and the Keyboard
While recording multiple parts one-by-one, you can adjust the volume balance between the playback of the
recorded parts and your current performance by using the [SONG VOLUME] slider.
Turning off the [MASTER] button lets you adjust the volume for the keyboard performance by using the
[ZONE CONTROL] sliders.
ZONE 1
ZONE 2
ZONE 3
ZONE 4
Move the sliders to make
adjustments in the sound.
SONG
VOLUME
ZONE CONTROL
CP300 Owner’s Manual
47
Recording Your Performance
Recording in Dual or Split Mode
When you record in Dual or Split mode, the CP300 records each Voice onto a separate track. The following
table shows how tracks are assigned to each Voice.
CAUTION
When you record multiple parts into tracks one-by-one, or when you record new data over an existing Song (page 46),
the existing data will be erased. Proceed with caution.
In the following example, Tracks 1, 2, and Extra Track “n” have been selected for recording.
Panel
Basic Operation
Dual
Assigned
recording track
TRACK
1
2
3-16
Track 1
Main part
TRACK
1
2
Track 2
Main part
3-16
Split
2
2
3-16
Main part
Left part
3-16
Main part
Left part
TRACK
1
2
TRACK
1
Dual+Split
2
2
2
2
Left part
(Track n+1)
Main part
Left part
Main Layer Left Layer
part
part
3-16
Main part
Left part
Main Layer Left Layer
part
part
TRACK
1
3-16
Main part
(Track n)
Left part
Main Layer Left Layer
(Track n+1) part
part
(Track n+2) (Track n+3)
Track n = Track 3 to 16
If “n+1,” “n+2,” and “n+3” exceeds 16, Tracks 1, 2, and 3 are used.
n Changing between Dual and Split mode in the middle of a Song cannot be recorded.
48
CP300 Owner’s Manual
Extra
Track 6
Layer part
(Track n+2)
3-16
TRACK
1
Main part
(Track n)
3-16
TRACK
1
Extra
Track 5
Layer part
Main part
(Track n)
3-16
TRACK
1
Extra
Track 4
Layer part
TRACK
1
Extra
Track 3
...
Extra
Track 16
Song Playback
Songs you’ve recorded using the Record function (page 41) as well as Preset Songs can be played back on the CP300. You can
also play the keyboard along with Song playback.
Playing Back a Song
TRACK
MASTER
PERFORMANCE
TRANSPOSE
SONG SELECT
1
2
3-16
REC
STOP
PLAY/PAUSE
MASTER EDIT PERFORM.FILE
SONG FILE
SONG SETTING
MIDI OUT PANEL LOCK
B
A
NO
DOWN
CONTRAST
YES
UP
GRAND
PIANO 1
GRAND
PIANO 2
MONO
PIANO
E. PIANO 1
E. PIANO 2
E. PIANO 3
CLAVI.
VIBES
1
ORGAN 1
2
ORGAN 2
3
HARPSI.
4
STRINGS
5
CHOIR/PAD
6
GUITAR
7
BASS
8
XG
9
10
11
12
13
14
15
16
VOICE EDIT
SPLIT
VARIATION
REVERB
CHORUS
MASTER EQ EDIT
SPEAKER
MIDI SETTING
CLICK
OTHER SETTING
Basic Operation
2
DEMO
EXIT
NEW SONG
SYNCHRO START
TEMPO
C
D
SONG
1, 3 5 4, 5
1
VOICE/PERFORMANCE
3
6
Press one of the SONG SELECT [N][O] buttons to call up the Song Select display.
A
B
PresetSong
P-000:NewSong
Bar 001
C
2
NO
YES
D
Select “Preset Song” or “Memory Song” by using the A [–][+] buttons.
The indication “Memory Song” can be called up when your Song data exists in internal storage memory.
Terminology
Preset: Preset Song Memory. Several Preset Songs (16 Songs) are built into this instrument.
Memory: Refers to the memory storage location for saving recorded data on this instrument.
3
4
Select the desired Song by using the C [–][+] buttons or SONG SELECT [N][O]
buttons.
Use the D [–][+] buttons to scroll through the Song name, if the name does not fit in the display.
Press the [PLAY/PAUSE] button to start playback.
n • Use the “Song Repeat” parameter in the Song Setting menu (page 87) to select repeat playback of all Songs or
repeat playback of a single Song.
• You can use the TEMPO [DOWN][UP] buttons to adjust the playback tempo as required before or during
playback (page 38).
• When the “Character Code” setting is different than that used when you named the Song, the title might be
displayed incorrectly. Change the CP300’s character type (“Character Code”) to that appropriate for the selected
Song (page 84).
5
6
Stop playback.
When playback is complete, the Song automatically stops and the CP300 returns to the top of the Song.
If you wish to stop playback in the middle of a Song, press the [STOP] button. Song playback can be
paused by pressing the [PLAY/PAUSE] button.
Press the [EXIT] button to go back to the Main display.
CP300 Owner’s Manual
49
Song Playback
Fast Forward and Rewind
The following operations can be performed in the Song select display:
• Use the B [– (NO)][+ (YES)] buttons to move back and forth (rewind and fast forward) through the Song
while the Song is played or stopped.
• Press the C [–] button during playback to locate the top of the current Song.
• Press the C [–] button twice (double-click) during playback to start playback from the previous Song.
• Press the C [+] button during playback to start playback from the next Song.
• Press the [STOP] button or simultaneously press the B [– (NO)][+ (YES)] buttons during playback or while
playback is stopped in the middle of the Song to locate the top of the Song.
Basic Operation
Resetting the Tempo
Whenever you select a new Preset Song, the tempo is automatically reset to the Song’s original value.
n Performance mode is automatically turned off if you start Song playback while Performance mode is on.
Automatically Starting Song Playback by Playing the Keyboard—
Synchro Start
You can pause playback to begin when you play the keyboard (Synchro Start). Hold down the [STOP] button
and press the [PLAY/PAUSE] button. The [PLAY/PAUSE] indicator will blink, and the CP300 will wait for
Synchro Start.
In this condition, playback begins as soon as you play the keyboard.
1. Hold down the [STOP] button
2. Press the [PLAY/PAUSE] button
REC
STOP
PLAY/PAUSE
REC
SYNCHRO START
STOP
PLAY/PAUSE
SYNCHRO START
Synchro Start standby mode
n If you press the [STOP] button while waiting, Synchro Start will be cancelled.
Pedal Play/Pause
You can alternately start or pause Song playback by pressing a pedal connected to the CP300’s [ASSIGNABLE
FOOT PEDAL] jack. A pedal connected to the [ASSIGNABLE FOOT PEDAL] jack can be assigned to play
and pause Preset Song playback from the “Pedal Play/Pause” parameter in the Other Settings function
described on page 70.
This is convenient when performing along with previously recorded parts—it lets you stop and start playback
of the recorded backing, while you add parts of your own live.
Turning Part Playback On and Off
While the CP300 is playing or stopped, pressing these track buttons turn off the indicators, and the data on
those parts will not be played. Pressing the part buttons toggles part playback on and off. Turning a playback
part off lets you play that part yourself while the other parts play back.
TRACK
1
2
Track 1
Track 3-16
Track 2
50
CP300 Owner’s Manual
3-16
Convenient Functions
This section covers various functions that you’ll find come in handy as you play and perform with the instrument.
Panel Lock Function
1
Basic Operation
The panel lock function can temporarily disable the panel operation and prevent unintended operation during
live performance.
Double-click the [PANEL LOCK] button (press it quickly twice).
The [PANEL LOCK] button lights. A “PANEL LOCK” message also appears in the display. While the
Panel Lock function is engaged, panel operations will be ignored.
MIDI OUT PANEL LOCK
A
B
****** PANEL LOCK ******
Grand Piano 1
C
2
NO
YES
D
To cancel Panel Lock, double-click the [PANEL LOCK] button.
The [PANEL LOCK] button turns off, and the display returns to the previous display.
n The Panel Lock function affects all controls, with the exception of the [MASTER VOLUME] dial, the [SONG
VOLUME] slider, the [ZONE CONTROL] sliders, the [MASTER EQUALIZER] sliders, the Modulation wheel,
the Pitch bend wheel, and the pedals.
MIDI Transmission On/Off
This parameter specifies whether the CP300 transmits MIDI data to an external MIDI device (On) or not
(Off ).
Pressing the [MIDI OUT] button alternates between On and Off. MIDI messages can be transmitted if the
button lamp is lit. MIDI messages cannot be transmitted if the lamp is off.
MIDI OUT PANEL LOCK
Lit: Enables sending of MIDI messages.
MIDI OUT PANEL LOCK
Off: Disables sending of MIDI messages.
n This button is equipped with certain MIDI safeguards and also turns off pedal messages during performance. Even
if you turn MIDI transmission off while holding a key, a key-off message will still be transmitted when you release
the key. Turning MIDI transmission off also sends the following MIDI messages: Sustain Off, Sostenuto Off, Soft
Pedal Off.
n Keep in mind that if you turn MIDI transmission off, MIDI signals will not be transmitted no matter what other
MIDI transmission settings (in Master Edit and MIDI Settings) are made.
CP300 Owner’s Manual
51
Convenient Functions
MIDI Panic Control
This function serves as a convenient MIDI “panic” switch during performance when using a connected
external tone generator. If the connected tone generator continues to sound (stuck notes, etc.) even after you’ve
released the keys of the CP-300, using this MIDI Panic control transmits the necessary messages to stop the
tone generator from sounding continuously.
Press the [REVERB] button while holding the [MIDI OUT] button.
A “MIDI PANIC SEND” message appears in the display.
Basic Operation
MIDI OUT PANEL LOCK
REVERB
CHORUS
A
B
*** MIDI PANIC SEND
***
NO
C
YES
D
n Keep in mind that MIDI Panic transmission will not function if MIDI transmission is set to Off (page 51).
MIDI Panic messages: All Note Off, All Sound Off, Reset All Controllers, Sustain Off, Sostenuto Off, Modulation
Depth Off, Pitch Bend Center, Channel Pressure Off
Built-in Speakers On/Off
This parameter specifies whether the CP300’s built-in speakers produce sound (On) or not (Off ).
Pressing the [SPEAKER] button alternates between On and Off. The built-in speakers produce sound if the
lamp is lit, and do not sound if the lamp is off.
SPEAKER
MIDI SETTING
CLICK
OTHER SETTING
DEMO
Lit: Speaker sounds normally.
SPEAKER
MIDI SETTING
CLICK
OTHER SETTING
DEMO
Off: Speakers do not sound.
n If the [SPEAKER] button is lit, the built-in speakers sound normally even when using the headphones.
52
CP300 Owner’s Manual
Master Settings—Master Edit
Reference Section
Master Settings—Master Edit
The Master mode allows you to divide the keyboard into up to four independent areas (zones) which will be effective when
the [MASTER] button is turned on.
n This setting is retained even after you turn off the power to the CP300. If you set the Memory Backup’s Master Setting to Off in the
Other Settings menu, the Master Settings will return to the default (initial) values when you turn on the power next time (page 71).
2
TRACK
MASTER
PERFORMANCE
TRANSPOSE
SONG SELECT
1
2
3-16
REC
STOP
PLAY/PAUSE
MASTER EDIT PERFORM.FILE
SONG FILE
SONG SETTING
MIDI OUT PANEL LOCK
B
A
NO
DOWN
CONTRAST
YES
UP
GRAND
PIANO 1
GRAND
PIANO 2
MONO
PIANO
E. PIANO 1
E. PIANO 2
E. PIANO 3
CLAVI.
VIBES
1
ORGAN 1
2
ORGAN 2
3
HARPSI.
4
STRINGS
5
CHOIR/PAD
6
GUITAR
7
BASS
8
XG
9
10
11
12
13
14
15
16
VOICE EDIT
SPLIT
VARIATION
REVERB
CHORUS
MASTER EQ EDIT
SPEAKER
MIDI SETTING
CLICK
OTHER SETTING
DEMO
EXIT
SYNCHRO START
C
TEMPO
D
SONG
1, 2
VOICE/PERFORMANCE
3
1
4
5
Press the [MASTER EDIT] button to call up the Master Setting display.
A
B
Slider
Zone1
C
2
3
4
5
Reference
NEW SONG
NO
YES
Volume
D
Select the desired item by pressing the [MASTER EDIT] button or by using the A [–]
[+] buttons.
For information about the parameters and their values, refer to “Parameters” on page 54.
Use the C [–][+] buttons to select a target item.
Use the D [–][+] buttons to change the value.
Press the [EXIT] button to exit the Master Setting display and return to normal play.
CP300 Owner’s Manual
53
Master Settings—Master Edit
Parameters
Slider Settings
Bank Select LSB Settings for MIDI
Transmission to an External Tone Generator
For assigning specific functions to each [ZONE
CONTROL] slider.
A
B
Slider
Zone 1
NO
YES
Volume
C
You can select specific Voices or programs on a connected
MIDI device by specifying a Bank Select LSB value, in
combination with the Bank Select MSB parameter (above)
and the Program Change parameter (below).
A
D
SendBankLsb
Zone 1
Setting targets: Zone 1, Zone 2, Zone 3, Zone 4
Functions/range: Volume, Modulation, Brightness, Harmonic
Content, After Touch, Control numbers 001 – 031, 033 – 095, Off
n If you select After Touch or control numbers 001 – 031,
033 – 095, the slider affects only connected MIDI
instruments and not the CP300 itself.
Setting range: 0 – 127
Reference
A
C
NO
The three specified MIDI messages—Bank Select MSB, Bank
Select LSB and Program Change—will be transmitted in the
following conditions:
• When turning on the Master mode.
• When changing any of the values of Bank Select MSB, Bank
Select LSB or Program Change when the Master mode is on.
• When selecting a Performance which was saved with the
Master mode on.
YES
0
D
Setting targets: Zone 1, Zone 2, Zone 3, Zone 4
Setting range: 0 – 127
Default setting: 0
The three specified MIDI messages—Bank Select MSB, Bank
Select LSB and Program Change—will be transmitted in the
following conditions:
• When turning on the Master mode.
• When changing any of the values of Bank Select MSB, Bank
Select LSB or Program Change when the Master mode is on.
• When selecting a Performance which was saved with the
Master mode on.
CP300 Owner’s Manual
Default setting: 0
Program Change Number Settings for MIDI
Transmission to an External Tone Generator
B
SendBankMsb
Zone 1
YES
D
Setting targets: Zone 1, Zone 2, Zone 3, Zone 4
You can select specific Voices or programs on a connected
MIDI device by specifying a Bank Select MSB value, in
combination with the Bank Select LSB and Program
Change parameters below.
NO
0
C
Default setting: Volume
Bank Select MSB Settings for MIDI
Transmission to an External Tone Generator
54
B
You can select specific Voices or programs on a connected
MIDI device by specifying a Program Change number, in
combination with the Bank Select MSB and Bank Select
LSB parameters above.
A
B
SendPG#
Zone 1
C
NO
YES
1
D
Setting targets: Zone 1, Zone 2, Zone 3, Zone 4
Setting range: 1 – 128
Default setting: 1
The three specified MIDI messages—Bank Select MSB, Bank
Select LSB and Program Change—will be transmitted in the
following conditions:
• When turning on the Master mode.
• When changing any of the values of Bank Select MSB, Bank
Select LSB or Program Change when the Master mode is on.
• When selecting a Performance which was saved with the
Master mode on.
Master Settings—Master Edit
Octave Setting for Connected External Tone
Generator
The pitch of a note can be shifted upward or downward in
steps of an octave in each zone. You can adjust the offset up
or down over a maximum range of two octaves.
A
MIDI Transmission Channel for Master Mode
Specifies the channels over which the CP300 transmits
MIDI data from each zone.
A
MidiOutChannel
Zone 1
B
Octave
Zone 1
B
NO
C
NO
YES
Ch1
D
YES
0
C
Setting targets: Zone 1, Zone 2, Zone 3, Zone 4
D
Setting range: Ch 1 – Ch 16, Off
Setting targets: Zone 1, Zone 2, Zone 3, Zone 4
Setting range: -2 – 0 – +2
-2 (two octaves lower), 0 (no pitch shift), +2 (two octaves higher)
Default setting: 0
The Octave setting is effective when the [MASTER] button is on.
It also affects the following settings:
Default settings:
Zone 1
Ch 1
Zone 2
Ch 2
Zone 3
Ch 3
Zone 4
Ch 4
Internal: [VOICE EDIT] Octave setting for each Voice
When the [MASTER] button is off, Octave affects the following:
n When the [MASTER] button is turned off, the “MIDI
Out Channel” setting in the MIDI Settings menu is used
for MIDI channel assignments.
Reference
MIDI Output: [MASTER EDIT] Octave setting for each zone
Internal and MIDI Output: [VOICE EDIT] Octave setting for each
Voice
Internal Tone Generator On/Off Status
Turns the sound from the internal tone generator on or off
for each part.
A
B
InternalTG
Zone 1
NO
YES
On
C
D
Setting targets: Zone 1, Zone 2, Zone 3, Zone 4
Settings: On/Off
Default setting: On
CP300 Owner’s Manual
55
Detailed Settings for the Voices—Voice Edit
You can make detailed settings for Voice. You can make these settings for each Voice (or each combination of Voices)
individually.
Voice Edit—Basic Operation
1
2
3
Select the desired Voice or combination of Voices.
For instructions on how to select a Voice, see page 25.
Press the [VOICE EDIT] button to access the Voice Edit menu.
Use the A [–][+] buttons to select the part for which you wish to change the Voice.
The range of the displayed part varies depending on the selected Voice.
Reference
Voice Part
Main
Display
Main
Octave
Setup
Set?-->
0
The Main part Voice can be set.
MAIN Voices (displayed with a single
Voice or in Split mode)
Main x Layer
MainXLayer
Set?-->
Octave(GrndPno1)
0
The Main part Voice and Layer
part Voice can be set.
Displayed when the MAIN side is in
Dual mode
Left
Left
Octave
Set?-->
0
The Left part Voice can be set.
Displayed in Split mode
Left x Left Layer
LeftXLeftLayer
Set?-->
Octave(GrndPno1)
0
The Left part Voice and Left
Layer Voice can be set.
Displayed when the LEFT side is in Dual
mode
n For details about the split point settings between the Main part and Left part, refer to the “To Change the Split
Point Setting” (page 32) or the “Split Point” parameter in the Other Settings menu (page 69). The split point
settings for the Layer part and Left Layer part can be changed via the “Split Point 2” parameter in the Other
Settings menu (page 69).
For information about the parameters and their values, refer to “Parameters” on page 58.
56
CP300 Owner’s Manual
Detailed Settings for the Voices—Voice Edit
Use the C [–][+] buttons to select a target item.
You can change the Voice for each part when Main x Layer or Left x Left Layer is selected in Step 3 (in
Dual mode). The target Voice name will be displayed in parentheses.
A
B
MainXLayer
Set?-->
Octave(GrndPno1)
0
NO
C
5
D
Use the D [–][+] buttons to change the value.
Press the [–][+] buttons simultaneously to instantly reset to the default setting.
A
B
Main
Octave
Set?-->
0
NO
C
6
YES
YES
D
Press the B [+ (YES)] button to execute the job.
To proceed, press the B [+ (YES)] button again. An “Executing” message appears and the data is saved.
When the operation is complete, a “Completed” message appears briefly, then returns to the previous
display.
A
Reference
4
B
Main
Octave
Executing
0
C
NO
YES
D
n This setting will be retained even if you turn off the power to the CP300. The previous settings will be restored
when you turn on the power next time and the same Voice or part you selected before turning the power off will
automatically be selected.
7
Press the [EXIT] button to exit from the Voice Edit settings.
CP300 Owner’s Manual
57
Detailed Settings for the Voices—Voice Edit
Parameters
When the Voice part is set to Main x Layer or Left x Left Layer, parameters indicated with an asterisk (*) below are set for
each part’s Voice individually.
Octave*
Detune (Dual mode only)
This allows you to shift the pitch of a note upward or
downward in octave steps, over a range of +/- two octaves.
A
B
Main
Octave
Set?-->
0
NO
This allows you to finely tune the pitches of the two Voices
selected in Dual mode away from each other. Used
especially with similar sounding Voices, this creates a
warmer, richer sound.
YES
A
C
B
MainxLayer
Detune
D
Setting range: -2 – 0 – +2
-2 (two octaves lower), 0 (no pitch shift), +2 (two octaves higher)
Set?-->
+3
NO
C
YES
D
Setting range: -20 – +20 (Positive (+) settings will raise the
pitch of the Main or Left Voice part’s sound and lower the pitch of
the Layer or Left Layer Voice part’s sound. Negative (-) settings
will do the opposite.)
Volume*
Reference
This allows you to set the volume level for each Voice part.
A
B
Main
Volume
Set?-->
115
NO
C
Reverb Type
YES
This determines the types of Reverb effects used for the
Voices of the Main and Main x Layer parts. The Reverb
Type settings here are also used for the Voices of the Left
and Left x Left Layer parts, respectively. (These cannot be
set independently from the Main and Main x Layer Voices.)
D
Setting range: 0 – 127
Pan (Stereo position)*
A
Main
ReverbType
This allows you to set the position of the sound in the
stereo field, left or right.
A
C
Set?-->
C
NO
Set?-->
Hall1
NO
C
YES
D
Settings:
B
Main
Pan
B
YES
D
Setting range: L64 (hard left) – C (center) – R63 (hard right)
Room
Simulates the reverberation of a room.
Hall1
Simulates the reverberation of a concert hall.
Hall2
Reverberation is slightly longer than that of Hall 1.
Stage
Reverberation suitable for a solo instrument sound.
Plate
Simulates the characteristic sound of a plate reverb.
Reverb Send*
This allows you to control the depth of the reverb effect for
the Voice.
n The reverb effect is not applied if “Reverb Send” is set to
“0.”
n Reverb Send can be set independently for all Voice
parts—Main, Main x Layer, Left, and Left x Left Layer.
A
B
Main
ReverbSend
C
Setting range: 0 – 127
58
CP300 Owner’s Manual
Set?-->
10
NO
YES
D
Detailed Settings for the Voices—Voice Edit
Insertion Effect Type*
This determines the types of Chorus effects used for the
Voices of the Main and Main x Layer parts. The Chorus
Type settings here are also used for the Voices of the Left
and Left x Left Layer parts, respectively. (These cannot be
set independently from the Main and Main x Layer Voices.)
A
A
Set?-->
Chorus
NO
C
YES
Settings:
Makes the sound more rich and spacious.
Celeste
Adds warm animation and spaciousness to the
sound.
Adds a sweeping, metallic sound, similar to a jet
airplane.
This allows you to control the depth of the chorus effect for
the Voice.
n Chorus Send can be set independently for all Voice
parts—Main, Main x Layer, Left, and Left x Left Layer.
B
Main
ChorusSend
Set?-->
48
NO
C
NO
Settings:
DelayLCR
Delay applied at left, center, and right positions.
DelayLR
Delay applied at left and right positions.
Echo
Echo-like delay
CrossDelay
Left and right delays are crossed.
Symphonic
Adds a rich and deep acoustic effect.
Rotary
Adds the vibrato effect of a rotary speaker.
Tremolo
Changes the volume level in rapid cycles.
VibeRotor
Produces the vibrato effect of a vibraphone.
AutoPan
Automatically pans the sound left to right and
back and forth.
Phaser
Changes the phase of the sound periodically,
creating sweeping effects.
AutoWah
Changes the center frequency of the wah filter
periodically.
SoundBoard
Simulates the reverberation of a piano
soundboard.
AmpSimulator
Recreates the distortion effect of a guitar amp.
Compressor
This squeezes the dynamic range of a sound,
giving the overall sound greater “punch” and
impact.
Off
No effect
YES
D
YES
D
Chorus Send*
A
Set?-->
SoundBoard
C
D
Chorus
B
Main
Ins.Type
B
Main
ChorusType
Flanger
This allows you to select from a variety of effects (other
than reverb and chorus).
Reference
Chorus Type
Setting range: 0 – 127
Vibe Rotor Speed*
Chorus On/Off
This allows you to set the [CHORUS] button on or off for
each Voice. When you select a Voice, the [CHORUS]
button on/off setting for the Voice automatically changes
according to this parameter’s setting.
n Even if this parameter is turned on, the chorus effect is
disabled if “Chorus Send” is set to 0.
A
This applies only to the Vibraphone Voice and allows you
to change the speed of the vibrato effect (controlled by the
Modulation wheel), simulating the electric rotor on an
actual vibraphone.
This is displayed only if “Vibe Rotor” is selected for the
“Ins. Type” parameter.
It enables you to set the speed of vibrato when you select
the Vibraphone Voice and use the Modulation wheel.
B
Main
ChorusOnOff
C
Set?-->
Off
A
NO
B
YES
Main
VibeRotorSpeed
D
C
Set?-->
6
NO
YES
D
Setting range: On/Off
Setting range: 1 – 10
CP300 Owner’s Manual
59
Detailed Settings for the Voices—Voice Edit
Vibe Rotor On/Off*
Brightness*
This applies only to the Vibraphone Voice and allows you
to turn the vibrato effect (controlled by the Modulation
wheel) on and off. This is displayed only if “Vibe Rotor” is
selected for the “Ins. Type” parameter. When the
Vibraphone Voice is selected, the Vibe Rotor effect is
automatically set to On.
This allows you to set the brightness of the sound.
A
B
Main
Brightness
Set?-->
0
NO
C
YES
D
Setting range: -64 – +63
A
B
Main
VibeRotorOnOff
Set?-->
On
NO
C
YES
Harmonic Content*
D
This allows you to adjust the resonance of the sound.
Setting range: On/Off
A
B
Main
HarmonicContent
Rotary Speed*
Reference
This allows you to set the rotation speed of the rotary
speaker effect. This is displayed only if “Rotary” is selected
for the “Ins. Type” parameter.
A
Set?-->
0
NO
C
D
Setting range: -64 – +63
B
Main
RotarySpeed
Set?-->
Slow
EQ Low Frequency*
NO
C
YES
This allows you to adjust the low-range frequency of the
part EQ.
D
Setting range: Slow/Fast
n For details about EQ or Equalizer, refer to page 36.
A
B
Main
EQ LowFreq.
Dry/Wet Balance*
This allows you to set the depth of the Insertion effect.
Some “Ins. Type” settings do not allow you to set the “Dry/
Wet Balance.”
A
Set?-->
80
NO
C
YES
D
Setting range: 32 Hz – 2.0 kHz
B
Main
Dry/WetBalance
Set?-->
D58>W
NO
C
YES
D
Setting range: D63>W – D=W – D<W63
D63>W (outputs only the original sound with almost no effect
applied)
EQ Low Gain*
This allows you to adjust the low-range gain (amount of
boost/cut of the low frequencies) of the part EQ.
A
D<W63 (outputs only the sound processed by the effect)
B
Main
EQ LowGain
D=W (dry/wet balance is even)
C
Setting range: -12 dB – +12 dB
60
YES
CP300 Owner’s Manual
Set?-->
0
NO
YES
D
Detailed Settings for the Voices—Voice Edit
EQ High Frequency*
Assigning the Pedal 1 Function
This allows you to adjust the high-range frequency of the
part EQ.
A
This allows you to assign a specific function to the pedal
connected to the [1 SUSTAIN] jack.
B
Main
EQ HighFreq.
Set?-->
4.0k
NO
C
A
Main
Pedal 1
YES
D
Set?-->
SustainCont
NO
C
Setting range: 500 Hz – 16 kHz
YES
D
Settings:
EQ High Gain*
This allows you to adjust the high-range gain (amount of
boost/cut of the high frequencies) of the part EQ.
A
B
Main
EQ HighGain
B
Set?-->
0
NO
C
Sustain
On/Off switch-type damper (page 33).
SustainCont
Damper function that sustains the sound longer
the further down you press the pedal (page 33)
Sostenuto
Sostenuto pedal (page 33)
Soft
Soft pedal (page 33)
Expression
Makes the sound softer or louder
Off
No function is assigned
YES
D
Reference
Assigning the Pedal 2 Function
Setting range: -12 dB – +12 dB
This allows you to assign a specific function to the pedal
connected to the [2 SOSTENUTO] jack.
Touch Sensitivity (Touch Sense)*
A
This allows you to determine the manner and degree to
which the volume level changes in response to your touch
on the keyboard (how hard you play). Since the volume
level of actual harpsichords and pipe organs does not
change regardless of how you play the keyboard, the normal
setting for these Voices is 127. (See the setting range below.)
A
C
Set?-->
64
NO
YES
D
Setting range: 0 – 64 – 127
0: Softest level
64: Normal touch response; optimum dynamic range
127: Loudest level; fixed (no change in response to touch)
Main
Pedal 2
Set?-->
Sostenuto
NO
C
YES
D
Setting range: same as “Pedal 1” (above)
Assigning the Pedal 3 Function
B
Main
TouchSense
B
This allows you to assign a specific function to the pedal
connected to the [3 SOFT] jack.
A
B
Main
Pedal 3
Set?-->
Soft
C
NO
YES
D
Setting range: same as “Pedal 1” (above)
CP300 Owner’s Manual
61
Detailed Settings for the Voices—Voice Edit
Assigning the Pedal 4 Function
Assigning the Modulation Wheel Function
This allows you to assign a specific function to the pedal
connected to the [4 AUX] jack.
A
A
B
Main
Pedal 4
Set?-->
Expression
C
NO
B
Main
Modulation
YES
Set?-->
Ctrl#001
NO
C
D
YES
D
Settings:
Settings:
Reference
Sustain
On/Off switch-type damper (page 33)
Expression
Makes the sound softer or louder.
SustainCont
Damper function that sustains the sound longer
the further down you press the pedal (page 33).
MainVolume
Changes the volume level of notes being played
in the Main part. (Displayed only when Main is in
Dual mode.)
Sostenuto
Sostenuto (page 33)
LayerVolume
Soft
Soft (page 33)
Expression
Makes the sound softer or louder.
Changes the volume level of notes being played
in the Layer part. (Displayed only when Main is in
Dual mode.)
ReverbSend
Adds reverb accents to notes being played.
LeftVolume
Changes the volume level of notes being played
in the Left part. (Displayed only when Left is in
Dual mode.)
LeftLayer
Volume
Changes the volume level of notes being played
in the Left Layer part. (Displayed only when Left
is in Dual mode.)
RotarySpeed
Changes the rotary speaker effect’s rotation
speed.
VibeRotor
Changes the vibraphone’s vibrato speed.
Modulation
Adds modulation accents.
ReverbSend
Adds reverb accents to notes being played.
ChorusSend
Adds chorus accents to notes being played.
Brightness
Adds brightness accents to notes being played.
Harmonic
Adds resonance accents to notes being played.
AfterTouch
Adds after-touch accents to notes being played
(MIDI transmit only).
Ctrl #0 – #119
Adds accents by controllers #0 – 119 to notes
being played (MIDI transmit only).
Off
No function is assigned.
ChorusSend
Adds chorus accents to notes being played.
Brightness
Adds brightness accents to notes being played.
Harmonic
Content
Adds resonance accents to notes being played.
AfterTouch
Adds after-touch accents to notes being played
(MIDI transmit only)
Ctrl #0 – #119
Adds accents by controllers #0 – 119 to notes
being played (MIDI transmit only).
Off
62
This allows you to specify the parameter controlled by the
modulation wheel.
No function is assigned.
CP300 Owner’s Manual
Detailed Settings for MIDI Operations—MIDI Settings
Here you can make settings for MIDI applications, such as MIDI receive/transmit channels and other settings necessary when
using the CP300 with other MIDI devices.
n These settings will be retained even if you turn off the power to the CP300. If you set the Memory Backup’s MIDI Setting to Off in
the Other Settings menu, the MIDI Settings will return to the default (initial) values when you turn on the power next time
(page 71).
n While the Master mode is turned on, the “MIDI Out Channel” parameter and “MIDI Out Select” parameter in the MIDI Settings
menu are not effective.
About MIDI
Reference
MIDI (Musical Instrument Digital Interface) is a standard format for data transmission/reception. It enables
the transfer of performance data and commands between MIDI devices and personal computers. Using MIDI,
you can control a connected MIDI device from the CP300, or control the CP300 from a connected MIDI
device or computer.
MIDI Channels
MIDI data is transferred over 16 channels numbered from 1 through 16. Using these channels, 1 – 16, the
performance data for sixteen different instrument parts can be simultaneously sent over one MIDI cable.
Think of the MIDI channels as TV channels. Each TV station transmits its broadcasts over a specific channel.
Your home TV set receives many different programs simultaneously from several TV stations and you select the
appropriate channel to watch the desired program.
Weather Report
News
1
2
News
2
MIDI operates on the same basic principle. The transmitting instrument sends MIDI data on a specific MIDI
channel (MIDI Transmit Channel) via a single MIDI cable to the receiving instrument. If the receiving
instrument’s MIDI channel (MIDI Receive Channel) matches the Transmit Channel, the receiving instrument
will sound according to the data sent by the transmitting instrument.
For detailed information on how to set the MIDI transmit channel and the MIDI receive channel, refer to
page 65.
MIDI
cable
MIDI Transmit channel 2
MIDI Receive channel 2
CP300 Owner’s Manual
63
Detailed Settings for MIDI Operations—MIDI Settings
MIDI Settings—Basic Operation
2
5
1, 2
TRACK
MASTER
PERFORMANCE
TRANSPOSE
SONG SELECT
1
2
3-16
REC
STOP
PLAY/PAUSE
MASTER EDIT PERFORM.FILE
SONG FILE
SONG SETTING
MIDI OUT PANEL LOCK
B
A
NO
DOWN
CONTRAST
YES
UP
GRAND
PIANO 1
GRAND
PIANO 2
MONO
PIANO
E. PIANO 1
E. PIANO 2
E. PIANO 3
CLAVI.
VIBES
1
ORGAN 1
2
ORGAN 2
3
HARPSI.
4
STRINGS
5
CHOIR/PAD
6
GUITAR
7
BASS
8
XG
9
10
11
12
13
14
15
16
VOICE EDIT
SPLIT
VARIATION
REVERB
CHORUS
MASTER EQ EDIT
SPEAKER
MIDI SETTING
CLICK
OTHER SETTING
DEMO
EXIT
NEW SONG
SYNCHRO START
TEMPO
C
D
SONG
VOICE/PERFORMANCE
3
1
2
Reference
3
4
4
6
Press the [MIDI SETTING] button to call up the MIDI Settings menu.
Select the desired item by pressing the [MIDI SETTING] button or by using the A [–]
[+] buttons.
For information about the parameters and their values, refer to “Parameters” on page 65.
Use the C [–][+] buttons to select a target item.
Use the D [–][+] buttons to change the value.
Press the [–][+] buttons simultaneously to instantly reset to the default setting.
A
B
MidiOutChannel
Main
NO
C
5
YES
Ch1
D
Press the B [+ (YES)] button to execute the job, if a “Start?” message appears.
Press the B [+ (YES)] button to call up the confirmation prompt (“Sure?”). Press the B [+ (YES)] button
once again to actually execute the job. An “Executing” message appears and the data is saved. When the
operation is complete, a “Completed” message appears briefly, then returns to the previous display.
To cancel the operation, press the B [– (NO)] button instead of the B [+ (YES)] button.
A
B
InitialSetup
Start?-->
NO
C
6
64
Press the [EXIT] button to exit the MIDI Settings menu.
CP300 Owner’s Manual
YES
D
Detailed Settings for MIDI Operations—MIDI Settings
Parameters
MIDI IN
(Ch 1 – Ch 16)
MIDI Transmit Channel Selection
USB
(Ch 1 – Ch 32)
This allows you to specify the channel over which the
CP300 transmits MIDI data.
A
B
MidiOutChannel
Main
NO
YES
Ch1
C
D
Selects the Voice part
Specifies the channel
Ch 1 – Ch 16
Song
Ch 17 – Ch 32
Song
Keyboard
Internal Voices
Setting targets: Main, Left, Layer, Left Layer
Setting range: Ch 1 – Ch 16, Off (not transmitted)
Default settings:
Ch 1
Left
Ch 2
Layer
Ch 3
Left Layer
Ch 4
Local Control On/Off
“Local Control On” is a state in which the CP300 produces
the sound from its tone generator when you play the
keyboard. In “Local Control Off ” state, the keyboard and
the tone generator are cut off from each other. This means
that even if you play the keyboard, the CP300 will not
produce the sound. Instead, the keyboard data can be
transmitted via MIDI to a connected MIDI device, which
can produce the sound. The “Local Control Off ” setting is
useful when you wish to play an external sound source
while playing the keys on the CP300, but don’t want the
CP300 to sound. It’s also useful for recording data to a
sequencer/computer and using the sequencer to route the
data to the appropriate tone generator or instrument.
n While the Master mode is turned on, “MIDI Out
Channel” parameter in the Master Edit menu will be
enabled for MIDI channel assignments.
MIDI Receive Channel Selection
This allows you to specify the channel over which the
CP300 receives data from the MIDI [IN] or USB
connectors.
A
A
Reference
Main
B
B
MidiInChannel
Ch1
LocalControl
NO
NO
C
C
YES
On
YES
Song
D
D
Selects the channel
Selects the MIDI receive part
Setting range: On/Off
Default setting: On
Setting targets: Song, Main, Left, Layer, Left Layer, Keyboard,
Off
Setting range: Ch 1 – Ch 32
Default settings:
MIDI Out Select
This allows you to select whether your performance data or
Song playback data is sent via MIDI.
A
B
Ch 1 – Ch 16
Song
Ch 17
Keyboard
Ch 18
Main
Ch 19
Left
Ch 20
Layer
Ch 21
Left Layer
Keyboard
Performance data played on the keyboard
Ch 22 – Ch 32
Off
Song
Song playback data
MidiOutSelect
NO
YES
Keyboard
C
D
Settings:
Default setting: Keyboard
n While the Master mode is turned on, keyboard
performance data is transmitted no matter what setting is
made here.
CP300 Owner’s Manual
65
Detailed Settings for MIDI Operations—MIDI Settings
MIDI Receive Parameter
Bulk Dump
This allows you to specify which types of MIDI data the
CP300 will receive and respond to.
A
You can transmit each setting data as the MIDI setting bulk
data.
B
ReceiveParameter
Note
NO
A
YES
On
C
D
Selects the type of data
B
BulkDump
Voice
Start?-->
NO
C
Turns reception on or off
YES
D
Type of data:
Type of data: Note, Control, Program, AfterTouch, PitchBend,
SysEx (System Exclusive)
Current
The data is set on the panel
Performance
The data saved to the Performance
Setting range: On/Off
Voice
The Voice data saved using Voice Edit
Default setting: On for all types of data
MemorySong/
Perf.File
The Performance file, the data saved to the
Song file.
ALL
Send each bulk in sequence.
MIDI Transmit Parameter
Default setting: Current
Reference
This allows you to specify which types of MIDI data the
CP300 will transmit.
A
B
TransmitParameter
Note
NO
YES
On
C
D
Selects the type of data
Turns transmission
on or off
Type of data: Note, Control, Program, AfterTouch, PitchBend,
SystemRealTime, SysEx (System Exclusive)
Setting range: On/Off
Default setting: On for all types of data
Transmitting the Default Settings on the Panel
This allows you to transmit initial panel setup data, such as
Voice selection and other settings, to a connected
sequencer. This is useful when you record performance data
to a sequencer, since it lets you take a “snapshot” of the
CP300 settings you want to use at the beginning of a
recorded Song and have those settings automatically called
up for you when you play back the Song.
A
B
InitialSetup
Start?-->
NO
C
66
CP300 Owner’s Manual
YES
D
Bulk data cannot be transmitted in the following situations:
• Song record/playback
• Song recording standby
• When selecting recording tracks
• Demo Song playback
Bulk data cannot be received in the following situations:
• Song record/playback
• Song recording standby
• When selecting recording tracks
• Demo Song playback
• When transmitting bulk data
• When the message “Receiving bulk data has failed” appears
If the Performance file has 56 files, or the Song file has 112
Songs (1.4 MB), the data transfer will take at least 3 minutes if
you are using the USB connection, or 21 minutes if you are using
the MIDI connection.
n If you’ve changed the “Character Code” setting (page 84)
since naming a Song and the Song name does not display
correctly, bulk data cannot be transmitted.
n Press the B [– (NO)] button or [EXIT] button to cancel
the transmission.
CAUTION
Never attempt to turn off the power while bulk data is being
transmitted. Turning the power off in this state results in loss of
all user data.
Miscellaneous CP300 Settings—Other Settings
The Other Setting(s) menu provides a variety of settings, generally related to the overall sound and operation of the CP300.
These include detailed settings for touch response, tuning, pedal operation, and more.
n The edited Other Settings will be erased after you turn off the power to the CP300. If you set the Memory Backup’s Other Setting
to On in the Other Settings menu, the current Other Settings’ values will remain in effect when you turn the power off and back on
again (page 71).
Other Settings—Basic Operation
2
5
TRACK
PERFORMANCE
TRANSPOSE
SONG SELECT
1
2
3-16
REC
STOP
PLAY/PAUSE
SONG FILE
SONG SETTING
MIDI OUT PANEL LOCK
B
A
NO
DOWN
CONTRAST
YES
UP
GRAND
PIANO 1
GRAND
PIANO 2
MONO
PIANO
E. PIANO 1
E. PIANO 2
E. PIANO 3
CLAVI.
VIBES
1
ORGAN 1
2
ORGAN 2
3
HARPSI.
4
STRINGS
5
CHOIR/PAD
6
GUITAR
7
BASS
8
XG
9
10
11
12
13
14
15
16
VOICE EDIT
SPLIT
VARIATION
REVERB
CHORUS
MASTER EQ EDIT
SPEAKER
MIDI SETTING
CLICK
OTHER SETTING
DEMO
EXIT
NEW SONG
SYNCHRO START
TEMPO
C
D
SONG
VOICE/PERFORMANCE
3
1
2
3
4
4
6
1, 2
Press the [OTHER SETTING] button to call up the Other Settings menu.
Select the desired item by pressing the [OTHER SETTING] button or by using the
A [–][+] buttons.
For information about the parameters and their values, refer to “Parameters” on page 68.
Use the C [–][+] buttons to select a target item.
Use the D [–][+] buttons to change the value.
Press the [–][+] buttons simultaneously to instantly reset to the default setting.
A
B
Transpose
Song
NO
D
Press the B [+ (YES)] button to execute the job (if an “Execute?” message appears).
Pressing the B [+ (YES)] button calls up a confirmation prompt (“Sure?”). Press the B [+ (YES)] button
again to execute the job. An “Executing” message appears and the data is saved. When the operation is
complete, a “Completed” message appears briefly, then returns to the previous display.
To cancel the operation, press the B [– (NO)] button instead of the B [+ (YES)] button.
A
B
FactorySet
Sure?-->
MemoryFileExcluded
NO
C
6
YES
0
C
5
Reference
MASTER
MASTER EDIT PERFORM.FILE
YES
D
Press the [EXIT] button to exit from the Other Settings menu.
CP300 Owner’s Manual
67
Miscellaneous CP300 Settings—Other Settings
Parameters
Settings:
Touch Response
This allows you to specify the touch response of the
CP300’s keyboard, or change how the sound responds to
the way you play the keys.
A
B
TouchResponse
Vel= 64
Fixed
NO
C
Stretch
Tuning curve particularly for pianos, with higher
octaves slightly “stretched.”
Flat
Tuning curve in which the frequency relationships are
precisely duplicated in all octaves.
Default setting: Stretch
YES
D
Scale
Settings:
Light
A soft playing touch results in a relatively loud sound.
The volume level tends to be consistent.
Medium
Standard touch response.
Heavy
The keys must be played very strongly to generate
loud volume. This setting is best for a wide dynamic
range and optimum expressive control of the sound,
from pianissimo to fortissimo.
Fixed
No touch response. The volume level will be the same
regardless of how strongly you play the keys. Use the
B [– (NO)][+ (YES)] buttons to set the fixed volume
level. Setting range of the fixed volume level: 1 – 127
This allows you to select different scales or tuning systems
for the instrument. Equal Temperament is the most
common contemporary piano tuning scale. However,
history has known numerous other scales, many of which
serve as the basis for certain genres of music. You can
experience these tunings with the CP300.
Reference
A
B
Scale
C
BaseNote=C
PureMajor
NO
YES
D
Default setting: Medium
Settings:
Equal
The pitch range of each octave is divided equally
into twelve parts, with each half-step evenly
spaced in pitch. This is the most commonly used
tuning in music today.
PureMajor
These tunings preserve the pure mathematical
intervals of each scale, especially for triad chords
(root, third, fifth). You can hear this best in actual
vocal harmonies—such as choirs and a cappella
singing.
Tune
This allows you to finely tune the pitch of the entire
instrument—a useful feature when playing the CP300
along with other instruments or CD music.
A
PureMinor
B
Tune
NO
Pythagorean
This scale was devised by the famous Greek
philosopher and is created from a series of
perfect fifths, which are collapsed into a single
octave. The 3rd in this tuning are slightly
unstable, but the 4th and 5th are beautiful and
suitable for some leads.
MeanTone
This scale was created as an improvement on the
Pythagorean scale, by making the major third
interval more “in tune.” It was especially popular
from the 16th century to the 18th century. Handel,
among others, used this scale.
Werckmeister
The Werckmeister and Kirnberger scales were
improvements on the mean-tone and
Pythagorean scales. The main feature of these
scales is that each key has its own unique
character. The scales were used extensively
during the time of Bach and Beethoven, and
even now are often used when performing period
music on the harpsichord.
YES
A3=440.0Hz
C
D
Setting range: A3 = 427.0 Hz – 453.0 Hz (0.1 Hz steps)
Default setting: A3 = 440.0 Hz
Piano Tuning Curve
This allows you to specify a tuning curve, Stretch or Flat,
for the Piano Voices groups (Grand Piano 1, Grand Piano 2
and Mono Piano). Actual piano tuners often employ stretch
tuning, extending the upper octaves of the piano slightly to
compensate for the perception of the human ear in the
higher range. The Flat setting is an acoustically perfect
tuning, to be used if the stretch-tuned piano Voice sounds
out of tune with other instrument Voices.
A
B
PianoTuningCurve
NO
YES
Stretch
C
68
CP300 Owner’s Manual
D
Kirnberger
Setting range: C, C#, D, Eb, E, F, F#, G, Ab, A, Bb, B
For scales other than Equal, a root note must be specified using
the B [– (NO)]/[+ (YES)] buttons.
Default setting: Equal
Miscellaneous CP300 Settings—Other Settings
Split Point
Soft Pedal Depth
This allows you to specify the split point (the boundary on
the keyboard separating the Main part and Left part).
This allows you to specify the depth of the soft pedal effect.
A
A
B
SoftPedalDepth
B
NO
SplitPoint(Main)
NO
F#2
C
C
D
YES
5
YES
D
Setting range: 1 – 10
Setting range: A-1 – C7
Default setting: 5
Default setting: F#2
String Resonance Depth
Split Point 2
This allows you to specify the secondary split point (the
boundary on the keyboard separating the Layer part and
Left Layer part).
A
This parameter sets the amount or depth of the String
Resonance sound and is effective on certain Voice, such as
Grand Piano 1.
A
B
StringResonanceDepth
B
NO
SplitPoint(Layer)
YES
5
YES
F#2
C
C
D
Reference
NO
D
Setting range: Off, 1 – 10
Setting range: A-1 – C7
Default setting: 5
Default setting: F#2
Sustain Sampling Depth
Transpose
The CP300’s Transpose function makes it possible to shift
the pitch of the entire keyboard up or down in semitone
intervals to facilitate playing in difficult key signatures, and
to let you easily match the pitch of the keyboard to the
range of a singer or other instruments.
This parameter sets the amount or depth of the Sustain
Sampling sound and is effective on the Mono Piano 1 and
Comp. Piano 1 Voices, as well as on the Grand Piano 1
Voice group.
A
B
SustainSamplingDepth
NO
A
Transpose
Keyboard
C
NO
D
YES
0
C
YES
5
B
Setting range: Off, 1 – 10
D
Default setting: 5
Setting targets:
Keyboard
The sound you play with the keys
Song
The sound of Song playback
Setting range: -12 – 0 – +12
-12 (-1 octave) – 0 (normal pitch) – +12 (+1 octave)
Default setting: Keyboard = 0, Song = 0
n The Keyboard settings can only be made when the
[TRANSPOSE] button is turned on (page 37).
n You can also change the keyboard Transpose setting by
using the [TRANSPOSE] button. Whichever method
you use, the most recently made settings will be effective.
n The Transpose setting affects transmitted MIDI data.
CP300 Owner’s Manual
69
Miscellaneous CP300 Settings—Other Settings
Key-off Sampling Depth
Pedal Type
This allows you to adjust the volume of the key-off sound
(the subtle sound that occurs when you release a key). This
parameter is effective on the Grand Piano 1, Mono Piano 1
and Comp. Piano 1 Voices, as well as on the E. Piano 1,
Clavi. and Harpsi Voice groups.
A
B
KeyoffSamplingDepth
NO
YES
5
C
D
This allows you to select the type or polarity of the pedals
you use, connected to the [SUSTAIN] pedal jack,
[SOSTENUTO] pedal jack, [SOFT] pedal jack and [AUX]
pedal jack. If you are using a Yamaha-recommended pedal
(such as the FC4 or FC5), the Pedal Type need not be
changed. However, if you are using a pedal of a different
manufacturer, the polarity may be opposite and the effect
produced by operating the pedal (on/off, dynamics, etc.)
might be reversed. If this happens, you can use this setting
to correct the pedal operation.
Setting range: Off, 1 – 10
A
Default setting: 5
B
PedalType
Pedal 1
NO
C
Vibraphone Pedal Mode
D
Setting for: Pedal 1, Pedal 2, Pedal 3, Pedal 4
Reference
This parameter affects only the Vibraphone Voice, and
enables you to select whether the Vibraphone sound is
sustained while you press the keys on the keyboard (“Piano
Like”) or the sound is sustained only while you press and
hold down the sustain pedal, like when playing an actual
vibraphone (“Normal”).
A
B
VibraphonePedalMode
PianoLike
NO
C
YES
D
Setting range: PianoLike, Normal
Default setting: PianoLike
Pedal Play/Pause
Setting range: Make, Break
Default settings: Pedal 1, Pedal 2, Pedal 3: Make; Pedal 4:
Break
Half Pedal Point
This allows you to set the point at which the damper pedal
starts to affect the sound. In other words, you can change
the point at which the assigned effect begins to be applied,
as you press the pedal down. If the effect is a simple on/off
type effect, this setting specifies the point at which the
effect will be switched on/off (with the exception of the
Expression function).
Refer to the section on assigning the pedal function in the
Voice Edit settings (page 61).
A
This allows you to assign the Song Play/Pause function to
the pedal, letting you start or pause Song playback with
your foot. In this setting, the selected pedal (2 – 4)
functions in the same manner as the [PLAY/PAUSE]
button on the panel.
n If you assign the Play/Pause function to a pedal and turn
the function On, the pedal function assigned to the pedal
in the Voice Edit menu (pages 61 and 62) is disabled.
A
C
Selects the pedal to which
the function will be assigned
NO
B
HalfPedalPoint
NO
YES
0
C
D
Setting range: -2 (effective with the shallowest press) – 0 – +2
(effective with the deepest press)
Default setting: 0
Pitch Bend Range
B
PedalPlay/Pause
Pedal 2
YES
Make
YES
Off
D
Selects on or off
This allows you to specify the amount of pitch change
produced by moving the Pitch bend wheel. This parameter
applies only to the manually played sound (not to a
connected MIDI device). The value can be set in semitone
steps.
Setting for: Pedal 2, Pedal 3, Pedal 4
A
Setting range: On/Off
B
PitchBendRange
NO
Default setting: Off for all pedals
YES
2
C
D
Setting range: 0 – 12 semitones (moving the wheel will raise/
lower the pitch by a maximum of 12 semitones or 1 octave)
Default setting: 2
70
CP300 Owner’s Manual
Miscellaneous CP300 Settings—Other Settings
Equalizer Lock
Factory Set
This allows you to lock the Master Equalizer settings and
prevent them from being changed when selecting a
Performance, or by Song playback and incoming MIDI
data.
However, if bulk data (of the Current type) is received, the
Master Equalizer settings will be changed, no matter
whether the "Equalizer Lock" is turned on or off. (See Bulk
Dump in the MIDI Settings on page 66.)
A
CAUTION
B
EqualizerLock
NO
YES
Off
C
This allows you to reset the CP300 to its default settings.
• The “Character Code” parameter setting does not change
(page 84).
• The “Memory Backup” parameter setting (On/Off ) is
reset to the default setting (left column).
• You can specify whether the files in the storage memory
are erased or kept.
Never attempt to turn off the power during factory set. Doing so
could result in damage to the data.
D
Resets the CP300
Setting range: On/Off
A
Default setting: On
B
FactorySet
Execute?-->
MemoryFileExcluded
C
NO
YES
D
Memory Backup
A
Selects whether the memory files
are erased or kept
Reference
This allows you to select specific items and parameters, such
as Voice selection and reverb type, to be automatically saved
upon shutdown, ensuring that they will not be lost when
you turn off the power to the CP300.
If the backup function is turned on for an item, the settings
for that item when power is turned off will be in effect the
next time power is turned on. If the backup function is
turned off for an item, the settings in memory are erased
when you turn off the power. In this case, when you turn
on the power to the unit, the default settings (the initial
settings) will be used. Refer to the “Factory Setting List” on
page 101.
Keep in mind that the backup settings themselves, the files
of the storage memory, and Character Code setting
(page 84) are always saved upon shutdown.
Selecting for storage memory:
MemoryFileExcluded
Memory Songs are kept.
MemoryFileIncluded
Memory Songs are erased.
B
MemoryBackUp
Transpose
NO
YES
Off
C
D
Selects the desired item
Selects on or off
Setting for:
Master
Master settings (page 53)
Transpose
Transpose settings (page 69)
Equalizer
Master Equalizer settings (page 72)
ReverbOnOff
Reverb on or off (page 35)
SplitPoint
Split Point settings (page 69)
Main/LeftVoice
Voice, Keyboard part combinations
(page 27)
SongSetting
Settings for Song recording and playback
(page 85)
MidiSetting
MIDI Settings (page 63)
OtherSetting
Other Settings (page 67)
Default setting: The Transpose, Main/LeftVoice and
OtherSetting parameters are set to Off. Other parameters are set
to On.
CP300 Owner’s Manual
71
Master Equalizer Settings
This section explains how to set the Master Equalizer using the Master EQ Edit menu.
n This setting is retained even after you turn off the power to the CP300. If you set the Memory Backup’s Equalizer setting to Off in
the Other Settings menu, the Master Equalizer settings will return to the default (initial) values when you turn on the power the
next time (page 71).
Specifies the type
TRACK
MASTER
PERFORMANCE
TRANSPOSE
SONG SELECT
1
2
3-16
REC
STOP
PLAY/PAUSE
MASTER EDIT PERFORM.FILE
SONG FILE
MIDI OUT PANEL LOCK
SONG SETTING
B
A
NO
DOWN
CONTRAST
YES
UP
GRAND
PIANO 1
GRAND
PIANO 2
MONO
PIANO
E. PIANO 1
E. PIANO 2
E. PIANO 3
CLAVI.
VIBES
1
ORGAN 1
2
ORGAN 2
3
HARPSI.
4
STRINGS
5
CHOIR/PAD
6
GUITAR
7
BASS
8
XG
9
10
11
12
13
14
15
16
VOICE EDIT
SPLIT
VARIATION
REVERB
CHORUS
MASTER EQ EDIT
SPEAKER
MIDI SETTING
CLICK
OTHER SETTING
DEMO
EXIT
NEW SONG
SYNCHRO START
C
TEMPO
D
SONG
VOICE/PERFORMANCE
Specifies the value
Specifies the item
1
MASTER EQ EDIT
[▼][▲] buttons
Use the MASTER EQ EDIT [▼][▲] buttons to show the Master EQ Edit display.
Master Equalizer type
A
B
Reference
Equalizer
LowGain
Edit
0dB
C
3
4
YES
D
Parameter name
2
NO
Parameter value
Set the Master Equalizer type by using the MASTER EQ EDIT [▼][▲] buttons or the
B [– (NO)][+ (YES)] buttons.
Setting range: Mellow 1 – 3, Normal, Bright 1 – 3, Edit
Default setting: Edit
Use the C [–][+] buttons to select the parameter item.
Use the D [–][+] buttons to change the value.
The contents of the EQ parameters are briefly explained below.
Parameter name
Contents
Data Range
gain*1
-9 dB – +9 dB*2
Low Gain
EQ low-range
Low Freq.
EQ low-range frequency
32 Hz – 2.0 kHz
Low Q
EQ low-range resonance
0.1 – 12.0
LowMid Gain
EQ low-middle range gain*1
-9 dB – +9 dB*2
LowMid Freq.
EQ low-middle frequency
100 Hz – 10.0 kHz
LowMid Q
EQ low-middle resonance
0.1 – 12.0
Mid Gain
EQ middle range gain*1
-9 dB – +9 dB*2
Mid Freq.
EQ middle frequency
100 Hz – 10.0 kHz
Mid Q
EQ middle resonance
0.1 – 12.0
HighMid Gain
EQ high-middle range gain*1
-9 dB – +9 dB*2
HighMid Freq.
EQ high-middle frequency
100 Hz – 10.0 kHz
HighMid Q
EQ high-middle resonance
0.1 – 12.0
High Gain
EQ high range gain*1
-9 dB – +9 dB*2
High Freq.
EQ high frequency
500 Hz – 16.0 kHz
High Q
EQ high resonance
0.1 – 12.0
*1 You can also set the EQ Gain by moving the [MASTER EQUALIZER] slider. Keep in mind that the most recently made
settings will be effective.
*2 You can specify the range of the gain from -12 dB to +12 dB on MIDI Input. The display will also indicate from -12 dB
to +12 dB.
n If the “Equalizer Lock” parameter (page 71) in the Other Settings menu is turned on, the Master Equalizer settings
will not be affected by selecting a Performance, or by Song playback and incoming MIDI data.
72
CP300 Owner’s Manual
Using the Performance Functions
The Performance functions allow you to store edited Voices, including Dual/Split settings, Voice and effect parameters, MIDI
transmit/receive channel settings and Master Edit settings, to the VOICE/PERFORMANCE [1] – [16] buttons. Once they
have been saved, the Performances can instantly be recalled from the panel. Refer to the section “Handling Performance Files”
on page 76.
You can save up to a total of 64 Performances to the VOICE/PERFORMANCE [1] – [16] buttons. A single button can
contain four different Performances, A – D.
To select the desired Performance (A – D), use the VARIATION [▼][▲] buttons.
Performance file
A Performance file is a single file that includes the data of 64 Performances.
Performance
• Dual/Split settings
• Voice and effect parameters
• MIDI transmit/receive channel
settings
• Master Edit settings
GRAND
PIANO 1
GRAND
PIANO 2
MONO
PIANO
E. PIANO 1
E. PIANO 2
E. PIANO 3
CLAVI.
VIBES
1
ORGAN 1
2
ORGAN 2
3
HARPSI.
4
STRINGS
5
CHOIR/PAD
6
GUITAR
7
BASS
8
XG
9
10
11
12
13
14
15
16
VARIATION
VOICE/PERFORMANCE
Reference
Switch the Performance
(A – D)
Performance D (16 Performances)
Performance C (16 Performances)
Performance B (16 Performances)
Performance A (16 Performances)
GRAND
PIANO 1
GRAND
PIANO 2
MONO
PIANO
E. PIANO 1
E. PIANO 2
E. PIANO 3
CLAVI.
VIBES
1
ORGAN 1
2
ORGAN 2
3
HARPSI.
4
STRINGS
5
CHOIR/PAD
6
GUITAR
7
BASS
8
XG
9
10
11
12
13
14
15
16
Performance file = 64 Performances
The current Performance, along with data of 64 Performances, is saved to the storage memory. For details
about recalling a Performance file from storage memory, refer to page 79.
Terminology
Storage memory: This memory area enables you to save Performance files and recorded Songs.
Performance
A01
Select the button
to save
GRAND
PIANO 1
GRAND
PIANO 2
MONO
PIANO
E. PIANO 1
E. PIANO 2
E. PIANO 3
CLAVI.
VIBES
1
ORGAN 1
2
ORGAN 2
3
HARPSI.
4
STRINGS
5
CHOIR/PAD
6
GUITAR
7
BASS
8
XG
9
10
11
12
13
14
15
16
VOICE/PERFORMANCE
Recalling a Performance file
from storage memory
Storage memory
Performance D
Performance C
Performance B
Performance D
Performance C
Performance B
Performance A
Performance D
Performance C
Performance B
Performance A
Performance A
GRAND
PIANO 1
GRAND
PIANO 2
MONO
PIANO
E. PIANO 1
E. PIANO 2
E. PIANO 3
CLAVI.
VIBES
GRAND
PIANO 1
GRAND
PIANO 2
MONO
PIANO
E. PIANO 1
E. PIANO 2
E. PIANO 3
CLAVI.
VIBES
GRAND
PIANO 1
GRAND
PIANO 2
MONO
PIANO
E. PIANO 1
E. PIANO 2
E. PIANO 3
CLAVI.
VIBES
1
ORGAN 1
2
ORGAN 2
3
HARPSI.
4
STRINGS
5
CHOIR/PAD
6
GUITAR
7
BASS
8
XG
1
ORGAN 1
2
ORGAN 2
3
HARPSI.
4
STRINGS
5
CHOIR/PAD
6
GUITAR
7
BASS
8
XG
1
ORGAN 1
2
ORGAN 2
3
HARPSI.
4
STRINGS
5
CHOIR/PAD
6
GUITAR
7
BASS
8
XG
9
10
11
12
13
14
15
16
9
10
11
12
13
14
15
16
9
10
11
12
13
14
15
16
Preset Performance file
= 64 Performances
Performance file
= 64 Performances
Performance file
= 64 Performances
CP300 Owner’s Manual
73
Using the Performance Functions
Performance Parameters
The useful Performance function enables you to store and recall all settings of the entire CP300 together,
including Dual/Split settings, Voice and effect parameters, MIDI transmit/receive channel settings and Master
Edit settings. Settings that can be edited and stored to a Performance are called “Performance parameters.”
Parameter menu
VOICE/
PERFORMANCE
Contents
Parameter name
–
25
Setting Dual
–
29
SPLIT
Setting Split
–
31
REVERB
Turning the Reverb on/off
–
35
MASTER
Turning the Master mode on/off
–
39
TRANSPOSE
Turning the Transpose on/off
–
37
Octave
58
VOICE EDIT
Setting the
octave*1
Setting the volume level*1
Volume
58
Setting the position of right and left channels*1
Pan
58
Make fine adjustments to the pitch (only in Dual mode)*1
Detune
58
Selecting the Reverb type*1
ReverbType
58
Reference
send*1
ReverbSend
58
Setting the Chorus type*1
ChorusType
59
ChorusSend
59
Setting the Reverb
Setting the Chorus send*1
Turning the Chorus on/off
*1
Selecting the Insertion effect type*1
Setting the speed of the Vibraphone vibrato effect*1
Turning the Vibraphone vibrato effect
on/off*1
Setting the rotation speed of the rotary speed*1
Adjusting the Insertion effect
depth*1
Adjusting the Brightness of the sound*1
Adjusting the Resonance effect*1
Adjusting the low-range frequency of the Part
equalizer*1
59
VibeRotorSpeed
59
VibeRotorOnOff
60
RotarySpeed
60
Dry/WetBalance
60
Brightness
60
HarmonicContent
60
60
EQHighFreq.
61
Adjusting the low-range gain of the Part equalizer*1
EQLowGain
60
EQHighGain
61
TouchSense
61
function*2
Pedal1
61
Setting the Pedal 2 function*2
Pedal2
61
Setting the Pedal 3 function*2
Pedal3
61
function*2
Pedal4
62
Setting the Pedal 1
Setting the Pedal 4
equalizer*1
Setting the Modulation wheel function*2
Modulation
62
Selecting the Master equalizer type*3
Edit or Master EQ type
name
72
Adjusting the low-range gain of the Master equalizer*3
LowGain
Adjusting the low-middle range gain of the Master equalizer*3
LowMidGain
Adjusting the middle range gain of the Master equalizer*3
MidGain
Adjusting the high-middle range gain of the Master
equalizer*3
Adjusting the high range gain of the Master equalizer*3
Adjusting the low-range frequency of the Master
equalizer*3
HighMidGain
HighGain
LowFreq.
Adjusting the low-middle frequency of the Master equalizer*3
LowMidFreq.
Adjusting the middle frequency of the Master equalizer*3
MidFreq.
Adjusting the high-middle frequency of the Master
equalizer*3
Adjusting the high frequency of the Master equalizer*3
CP300 Owner’s Manual
59
Ins.Type
EQLowFreq.
Setting the Touch Sensitivity*1
MASTER EQ EDIT
ChorusOnOff
Adjusting the high frequency of the Part equalizer*1
Adjusting the high range gain of the Part
74
Page
Selecting a Voice*1
HighMidFreq.
HighFreq.
Using the Performance Functions
Contents
Parameter name
Adjusting the low-range resonance of the Master equalizer*3
Adjusting the low-middle resonance of the Master
equalizer*3
Adjusting the middle resonance of the Master equalizer*3
Adjusting the high-middle resonance of the Master
MIDI SETTING
OTHER SETTING
MASTER EDIT
equalizer*3
LowQ
Page
72
LowMidQ
MidQ
HighMidQ
Adjusting the high resonance of the Master equalizer*3
HighQ
Setting the MIDI transmit channel
MidiOutChannel
65
Setting the MIDI receive channel
MidiInChannel
65
Turning Local Control on/off
LocalControl
65
Selecting Performance from the keyboard or Song data for
MIDI transmission
MidiOutSelect
65
68
Selecting the Touch Response
TouchResponse
Selecting a tuning curve for a Piano Voice
PianoTuningCurve
68
Selecting a scale
Scale
68
Specifying the Split Point (Main)
SplitPoint (Main)
69
Specifying the Split Point 2 (Layer)
SplitPoint2 (Layer)
69
Changing the key
Transpose
69
Adjusting the depth of the Soft pedal
SoftPedalDepth
69
Setting the depth of String Resonance
StringResonanceDepth
69
Setting the depth of Sustain Sampling for the Sustain pedal
SustainSamplingDepth
69
Specifying the volume of the Key-off sound
KeyOffSamplingDepth
70
Selecting a pedal function for Vibraphone Voice
VibraphonePedalMode
70
Assigning the SONG [PLAY/PAUSE] function to the pedal
PedalPlay/Pause
70
Setting the point at which the Sustain pedal starts to affect the
sound
HalfPedalPoint
70
Setting the Pitch bend range
PitchBendRange
70
Assigning a function to the [ZONE CONTROL] slider
Slider
54
Setting the MSB of the Send Bank Select message
SendBankMsb
54
Setting the LSB of the Send Bank Select message
SendBankLsb
54
Setting the Program Change message
SendPG#
54
Setting the octave of the external tone generator
Octave
55
Turning the internal tone generator on/off
InterITG
55
Setting the MIDI transmit channel when the Master mode is
turned on
MidiOutChannel
55
Reference
Parameter menu
MASTER EQ EDIT
*1 The value of the parameter varies depending on the Dual (page 29) and Split (page 31) settings.
*2 The value of the parameter varies depending on the Split settings (page 31).
*3 If the Equalizer Lock parameter in the Other Settings menu is turned on, recalling a Performance from the panel will
not update the parameter settings (page 71).
CP300 Owner’s Manual
75
Handling Performance Files
File displays (accessed via the [PERFORM.FILE] button) enable you to handle and organize files (e.g., save, delete and
rename Performance files) from the display.
Setting
Parameter name
Page
Saving a Performance
Performance
77
Renaming a Performance
Perf.Name
78
Saving as a Performance file
SaveAs
79
Recalling the Performance file from the storage memory
LoadFromMem.
79
Deleting a Performance file
DeleteFile
80
Renaming a Performance file
RenameFile
80
Performance File—Basic Operation
Reference
A message (information or confirmation prompt) sometimes appears on the display to facilitate operation.
Refer to the “Message List” on page 94 for an explanation of each message, along with the appropriate actions
to take.
3
4
TRACK
MASTER
PERFORMANCE
TRANSPOSE
SONG SELECT
1
2
3-16
REC
STOP
PLAY/PAUSE
MASTER EDIT PERFORM.FILE
SONG FILE
SONG SETTING
MIDI OUT PANEL LOCK
B
A
NO
DOWN
CONTRAST
YES
UP
GRAND
PIANO 1
GRAND
PIANO 2
MONO
PIANO
E. PIANO 1
E. PIANO 2
E. PIANO 3
CLAVI.
VIBES
1
ORGAN 1
2
ORGAN 2
3
HARPSI.
4
STRINGS
5
CHOIR/PAD
6
GUITAR
7
BASS
8
XG
9
10
11
12
13
14
15
16
VOICE EDIT
SPLIT
VARIATION
REVERB
CHORUS
MASTER EQ EDIT
SPEAKER
MIDI SETTING
CLICK
OTHER SETTING
DEMO
EXIT
NEW SONG
SYNCHRO START
C
TEMPO
D
SONG
2, 3
VOICE/PERFORMANCE
4
1
4
5
Prepare the file(s) for handling.
When using the Performance or Save As parameters:
Select the edited Voice or Performance file you want to save.
When using the Perf. Name, Rename File, Load From Mem. and Delete File parameters:
No operations necessary; go on to Step 2 below.
2
3
Press the [PERFORM.FILE] button to enter the Performance File settings.
Select the desired item by pressing the [PERFORM.FILE] button or by using the A [–]
[+] buttons.
A
B
Performance
A01.Piano+Pad
Set?-->
NO
C
YES
D
To close the Performance File menu, press the [EXIT] button once or twice.
4
5
76
Use the B [– (NO)][+ (YES)] to D [–][+] buttons to change the value.
For details about each operation, refer to pages 77 – 80.
Press the [EXIT] button to exit from the Performance File settings.
CP300 Owner’s Manual
Handling Performance Files
Saving a Performance—Performance
You can save the edited Performance to one of the VOICE/PERFORMANCE [1] – [16] buttons. For details
about the parameters you can store to a Performance and their contents, refer to the “Performance Parameters”
list (page 74). The Performance data is stored to storage memory as a Performance file. For instructions on
recalling a Performance file from storage memory, refer to page 79.
CAUTION
If you create a Performance by editing an existing Preset Performance file, a new Performance file named
“PresetPerformance.PER” will be made. The Preset Performance file is not overwritten; however, the edited
Performance can be overwritten without any warning. To avoid overwriting the data, save it as another Performance file
with the Save As operation or rename the Performance file with Rename File.
A
B
Performance
A01.Piano+Pad
Set?-->
NO
C
YES
D
4-1
Reference
For basic operation instructions, refer to page 76.
The following steps are detailed instructions for Step 4 (in the Basic Operation above).
Select the desired Performance by using the VARIATION [▼][▲] buttons or the C [–]
[+] buttons.
The location for saving the Performance can be specified from A01 to D16.
Performance D (16 Performances)
Performance C (16 Performances)
Performance B (16 Performances)
Performance A (16 Performances)
A01
GRAND
PIANO 1
GRAND
PIANO 2
MONO
PIANO
E. PIANO 1
E. PIANO 2
E. PIANO 3
CLAVI.
VIBES
1
ORGAN 1
2
ORGAN 2
3
HARPSI.
4
STRINGS
5
CHOIR/PAD
6
GUITAR
7
BASS
8
XG
9
10
11
12
13
14
15
16
Save
Performance file = 64 Performances
4-2
Press the B [+ (YES)] button to execute the job.
An “Executing” message appears and the data is saved. When the operation is complete, a “Completed”
message appears briefly, then returns to the previous display.
CAUTION
Never attempt to turn the [POWER] switch OFF while the “Executing” message is shown in the display. Turning
the power off in this state may cause the Performance file to be deleted.
CP300 Owner’s Manual
77
Handling Performance Files
Renaming a Performance—Perf. Name
This allows you to rename the Performance.
A
B
Perf.Name
A01.Piano+Pad
Set?-->
C
NO
YES
D
For basic operation instructions, refer to page 76.
The following steps are detailed instructions for Step 4 (in the Basic Operation above).
4-1
Renaming a Performance.
To move the cursor (small underline), use the C [–][+] buttons.
To insert a space, press the C [–][+] buttons simultaneously.
To select a character on the cursor, use the D [–][+] buttons.
To delete a character, press the D [–][+] buttons simultaneously.
You can use up to 20 characters for a Performance name.
Reference
You can change the type of characters on the display using the “Character Code” parameter in the Song
File menu.
4-2
Press the B [+ (YES)] button to execute the job.
An “Executing” message appears and the data is saved. When the operation is complete, a “Completed”
message appears briefly, then returns to the previous display.
CAUTION
Never attempt to turn the [POWER] switch OFF while the “Executing” message is shown in the display. Turning
the power off in this state may cause the Performance file to be deleted.
78
CP300 Owner’s Manual
Handling Performance Files
Saving as a Performance File—Save As
This allows you to save the Performance file as another file, under another file name.
A
B
SaveAs
Execute?-->
001.PresetPerformance
NO
C
YES
D
For basic operation instructions, refer to page 76.
The following steps are detailed instructions for Step 4 (in the Basic Operation above).
4-1
Name the Performance as described in the “Perf.Name” section (page 78).
4-2
Press the B [+ (YES)] button to execute the job.
Press the B [+ (YES)] button to display the confirmation prompt (“Sure?”).
To proceed, press the B [+ (YES)] button again. An “Executing” message appears and the data is saved.
When the operation is complete, a “Completed” message appears briefly, then returns to the previous
display.
To cancel the operation, press the B [– (NO)] button instead of the B [+ (YES)] button.
Reference
If storage memory contains one or more Performance files, and you save a Performance file, the CP300
automatically sorts the Songs alphabetically and renumbers them.
CAUTION
Never attempt to turn the [POWER] switch OFF while the “Executing” message is shown in the display. Turning
the power off in this state may cause the Performance file to be deleted.
Recalling the Performance File from the Storage Memory—Load From Memory
This allows you to recall the Performance file from storage memory. A single Performance file consists of 64
separate Performances. The Performance file in the current memory will be replaced with the selected
Performance file in the storage memory.
A
B
LoadFromMem. Execute?-->
001.PresetPerformance
C
NO
YES
D
For basic operation instructions, refer to page 76.
The following steps are detailed instructions for Step 4 (in the Basic Operation above).
4-1
Use the C [–][+] buttons to select the desired Performance file to be loaded.
4-2
Press the B [+ (YES)] button to execute the job.
Press the B [+ (YES)] button to display the confirmation prompt (“Sure?”).
To proceed, press the B [+ (YES)] button again. An “Executing” message appears and the data is saved.
When the operation is complete, a “Completed” message appears briefly, then returns to the previous
display.
To cancel the operation, press the B [– (NO)] button instead of the B [+ (YES)] button.
CAUTION
Never attempt to turn the [POWER] switch OFF while the “Executing” message is shown in the display. Turning
the power off in this state may cause the Performance file to be deleted.
n The Performance file loaded from the storage memory is effective after restarting the CP300.
CP300 Owner’s Manual
79
Handling Performance Files
Deleting a Performance File—Delete File
This allows you to delete a Performance file from the CP300’s storage memory. It is not possible to delete a
Preset Performance file and current Performance file.
A
B
DeleteFile
Execute?-->
001.MyPerformance.PER
NO
C
YES
D
For basic operation instructions, refer to page 76.
The following steps are detailed instructions for Step 4 (in the Basic Operation above).
4-1 Use the C [–][+] buttons to select the Performance file to be deleted.
Reference
4-2 Press the B [+ (YES)] button to execute the job.
Press the B [+ (YES)] button to display the confirmation prompt (“Sure?”).
To proceed, press the B [+ (YES)] button again. An “Executing” message appears and the data is saved.
When the operation is complete, a “Completed” message appears briefly, then returns to the previous
display.
To cancel the operation, press the B [– (NO)] button instead of the B [+ (YES)] button.
CAUTION
Never attempt to turn the [POWER] switch OFF while the “Executing” message is shown in the display. Turning
the power off in this state may damage the data of the Performance.
n The Performance file in the current memory cannot be deleted. After you delete a Performance file, the CP300
automatically updates the Performance file numbers.
Renaming a Performance File—Rename File
You can rename a Performance file in the storage memory. You cannot change the Preset Performance file.
A
B
RenameFile
Execute?-->
001.MyPerformance.PER
C
NO
YES
D
For basic operation instructions, refer to page 76.
The following steps are detailed instructions for Step 4 (in the Basic Operation above).
4-1
Name the Performance file as described in the “Perf.Name” section (page 78).
4-2
Press the B [+ (YES)] button to execute the job.
After you rename a Performance, the CP300 sorts Performance files alphabetically and renumbers them.
CAUTION
Never attempt to turn the [POWER] switch OFF while the “Executing” message is shown in the display. Turning
the power off in this state may cause the Performance file to be deleted.
80
CP300 Owner’s Manual
Handling Song Files
File displays (accessed via the [SONG FILE] button) enable you to handle and organize files (e.g., save, delete and rename
Song files) and change characters from the display.
Setting
Parameter name
Saving recorded Songs to the CP300’s storage memory
Page
SaveToMemory
82
Deleting a Song from the CP300’s storage memory
DeleteSong
83
Renaming Song files
RenameSongs
83
Changing the type of characters in display
CharacterCode
84
Terminology
Song file: On the CP300, a Song file includes both Song data and a Song number.
Song File—Basic Operation
2, 3
4
3
TRACK
MASTER
PERFORMANCE
TRANSPOSE
SONG SELECT
1
2
3-16
REC
STOP
PLAY/PAUSE
MASTER EDIT PERFORM.FILE
SONG FILE
SONG SETTING
MIDI OUT PANEL LOCK
B
A
NO
DOWN
Reference
A message (information or confirmation prompt) sometimes appears on the display to facilitate operation.
Refer to the “Message List” on page 94 for an explanation of each message, along with troubleshooting
information and the appropriate actions to take.
CONTRAST
YES
UP
GRAND
PIANO 1
GRAND
PIANO 2
MONO
PIANO
E. PIANO 1
E. PIANO 2
E. PIANO 3
CLAVI.
VIBES
1
ORGAN 1
2
ORGAN 2
3
HARPSI.
4
STRINGS
5
CHOIR/PAD
6
GUITAR
7
BASS
8
XG
9
10
11
12
13
14
15
16
VOICE EDIT
SPLIT
VARIATION
REVERB
CHORUS
MASTER EQ EDIT
SPEAKER
MIDI SETTING
CLICK
OTHER SETTING
DEMO
EXIT
NEW SONG
SYNCHRO START
TEMPO
C
D
SONG
1
1
VOICE/PERFORMANCE
4
4
5
Prepare the file(s) for handling.
When using the Save To Memory, Rename Song and Delete Song parameters:
Use the SONG SELECT [N] [O] buttons to select the target Song.
When using the Character Code parameter:
No operations necessary; go on to Step 2 below.
2
3
Press the [SONG FILE] button to access the Song File settings.
Select the desired item by pressing the [SONG FILE] button or by using the A [–][+]
buttons.
A
B
RenameSong
Execute?-->
M-001:NewSong.MID
C
NO
YES
D
To close the Song File menu, press the [EXIT] button once or twice.
4
5
Press the B [– (NO)][+ (YES)] to D [–][+] button to execute the job or change the value.
For details about each operation, refer to pages 82 – 84.
Press the [EXIT] button to exit the Song File settings.
CP300 Owner’s Manual
81
Handling Song Files
Saving Recorded Songs to the CP300’s Storage Memory—Save To Memory
This allows you to save recorded Songs to the CP300’s storage memory. Keep in mind that when you turn off
the power to the CP300, your recorded Song data will be lost. To permanently save the recorded Song, you
must save it to the CP300’s storage memory.
Current memory
Storage memory
This is a temporary memory area
where you can temporarily place
and edit the currently selected
Song before playback or recording.
This is a memory area that provides space for saving
recorded Songs that would normally be lost when
you turn off the power.
A recorded
Song
Save
Memory
Song
Preset
Song
A
B
SaveToMemory Execute?-->
M-001:NewSong.MID
C
NO
YES
D
Reference
The Save To Memory operation is not available for Preset Songs.
For basic operation instructions, refer to page 81.
The following steps are detailed instructions for Step 4 (in the Basic Operation above).
4-1
Name the Song.
To move the cursor (small underline), use the C [–][+] buttons.
To insert a space, press the C [–][+] buttons simultaneously.
To select a character on the cursor, use the D [–][+] buttons.
To delete a character, press the D [–][+] buttons simultaneously.
You can use up to 58 characters for a Song name. If the name is longer than the display, use the C [–][+]
buttons to move the cursor and scroll through the name.
You can change the type of characters on the display using the “Character Code” parameter (page 84).
4-2
Press the B [– (NO)][+ (YES)] button to execute the job.
Press the B [+ (YES)] button to display the confirmation prompt (“Sure?”).
To proceed, press the B [+ (YES)] button again. An “Executing” message appears and the data is saved.
When the operation is complete, a “Completed” message appears briefly, then returns to the previous
display.
To cancel the operation, press the B [– (NO)] button instead of the B [+ (YES)] button.
CAUTION
Never attempt to turn the [POWER] switch OFF while the “Executing” message is shown in the display. Turning
the power off in this state may cause the recorded Song to be deleted.
The Song is automatically numbered as “Mxx,” where “M” stands for “Memory” and “xx” is a number.
If storage memory contains one or more Songs, and you save a new Song, the CP300 automatically sorts the
Songs alphabetically and renumbers them.
82
CP300 Owner’s Manual
Handling Song Files
Deleting a Song from the CP300’s Storage Memory—Delete Song
This allows you to delete a Song from the CP300’s storage memory. It is not possible to delete a Preset Song.
A
B
DeleteSong
Execute?-->
M-001:NewSong.MID
NO
C
YES
D
For basic operation instructions, refer to page 85.
The following steps are detailed instructions for Step 4 (in the Basic Operation above).
4-1
Use the C [–][+] buttons to select a Song to delete.
4-2
Press the B [+ (YES)] button to execute the job.
Press the B [+ (YES)] button to display the confirmation prompt (“Sure?”).
To proceed, press the B [+ (YES)] button again. An “Executing” message appears and the data is saved.
When the operation is complete, a “Completed” message appears briefly, then returns to the previous
display.
Reference
CAUTION
Never attempt to turn the [POWER] switch OFF while the “Executing” message is shown in the display. Turning
the power off in this state may damage the data of the recorded Song.
n After you delete a Song, the CP300 automatically updates the Song numbers.
Renaming Song Files—Rename Song
This allows you to rename Song files. The titles of any Songs can be changed, with the exception of the Preset
Songs and “P-000:NewSong.”
A
B
RenameSong
Execute?-->
M-001:NewSong.MID
C
NO
YES
D
For basic operation instructions, refer to page 81.
The following steps are detailed instructions for Step 4 (in the Basic Operation above).
4-1
Name the Song as described in the Save To Memory operation (page 82).
4-2
Press the B [+ (YES)] button to execute the job.
After you rename a Song, the CP300 sorts all Songs alphabetically and renumbers them.
CAUTION
Never attempt to turn the [POWER] switch OFF while the “Executing” message is shown in the display. Turning
the power off in this state may cause the recorded Song to be deleted.
CP300 Owner’s Manual
83
Handling Song Files
Changing the Type of Characters in Display—Character Code
This allows you to change the type of characters that appear on display. The instructions below correspond to
Step 4 in the Basic Operation on page 81.
A
B
CharacterCode
International
C
4
NO
YES
D
Use the D [–][+] buttons to select “International” or “Japanese.”
Settings: International, Japanese
Character List
Japanese
International
Reference
n File names using the characters shown in gray above will not display correctly if the Character Code setting has
been changed.
n The Character Code setting is also reflected in the display for the Performance and Performance file names.
84
CP300 Owner’s Manual
Settings for Song Recording and Playback—
Song Settings
From this menu, you can make detailed settings for the selected Song. First, select the desired Song (page 49).
Song Settings—Basic Operation
2
3, 4
TRACK
PERFORMANCE
TRANSPOSE
SONG SELECT
SONG FILE
1
2
3-16
REC
STOP
PLAY/PAUSE
SONG SETTING
MIDI OUT PANEL LOCK
B
A
NO
DOWN
CONTRAST
YES
UP
GRAND
PIANO 1
GRAND
PIANO 2
MONO
PIANO
E. PIANO 1
E. PIANO 2
E. PIANO 3
CLAVI.
VIBES
1
ORGAN 1
2
ORGAN 2
3
HARPSI.
4
STRINGS
5
CHOIR/PAD
6
GUITAR
7
BASS
8
XG
9
10
11
12
13
14
15
16
VOICE EDIT
SPLIT
VARIATION
REVERB
CHORUS
MASTER EQ EDIT
SPEAKER
MIDI SETTING
CLICK
OTHER SETTING
DEMO
EXIT
NEW SONG
SYNCHRO START
TEMPO
C
D
SONG
VOICE/PERFORMANCE
1, 2
1
2
3
3
5
Press the [SONG SETTING] button to access the Song Settings menu.
Select the desired item by pressing the [SONG SETTING] button or by using the
A [–][+] buttons.
A
B
Quantize
Execute?-->
Off
C
3
4
5
Reference
MASTER
MASTER EDIT PERFORM.FILE
NO
YES
D
Use the B [– (NO)][+ (YES)] to D [–][+] buttons to execute the job or change the value.
Press the [–][+] buttons simultaneously to instantly reset to the default setting.
Press the B [+ (YES)] button to execute the job, if an “Execute?” or “Start?” prompt
appears.
Press the B [+ (YES)] button to display the confirmation prompt (“Sure?”).
To proceed, press the B [+ (YES)] button again. An “Executing” message appears and the data is saved.
When the operation is complete, a “Completed” message appears briefly, then returns to the previous
display.
To cancel the operation, press the B [– (NO)] button instead of the B [+ (YES)] button.
Press the [EXIT] button to exit from the Song Settings menu.
n Save the edited Song data by using the “Save To Memory” operation in the Song File menu.
CP300 Owner’s Manual
85
Settings for Song Recording and Playback—Song Settings
Parameters
Quantize
Quick Play
This allows you to correct the timing of notes you’ve
recorded. For example, if the timing of your performance
was slightly off in places, you can adjust the notes to precise
eighth or sixteenth notes. Changes made in Quantize affect
the entire Song.
A
B
Quantize
Execute?-->
SwingRate= 50%
1/8
C
NO
YES
This allows you to specify whether a Song that starts at a
point other than the first beat of the first measure should be
played from the first actual note or from the beginning of
the Song. (Some Songs are recorded with initial settings and
non-note data at the very beginning of the Song; this
parameter allows you to skip those settings and play the
Song from the first note. It also allows you to skip over rests
that naturally occur before the pickup note in a Song.)
A
D
Changes the swing rate
B
QuickPlay
Selects the notes for which
you can adjust the timing
NO
YES
On
C
D
Quantize timing settings (according to note value):
Settings:
Off
Reference
1/4 .............
Quarter note
1/8 .............
Eighth note
On
Playback from the first note
Off
Playback from the start of the Song (including a rest
or blank measure)
Default setting: On
1/12 ...........
Eighth note triplets
1/16 ...........
Sixteenth note
1/24 ...........
Sixteenth note triplets
If you select “1/8” or “1/16” for correction, the Swing Rate
parameter is shown (as a percentage value). Changing the
Swing Rate will make the Song sound more lively and give it
more of a swing or jazzy feel.
Channel Listen
This allows you to select and audition the recorded contents
of a single channel. Playback starts from the first note.
A
B
ChannelListen
Start?-->
Ch1
NO
C
YES
D
Setting range: 0% – 100%
Setting range: Ch 1 – Ch 16
If you select “1/8” for correction:
Default setting: Ch 1
Your keyboard performance
n Song data consists of 16 channels. Each instrument part is
assigned to a specific channel, so for this instrument, the
words “channel” and “track” have the same meaning.
Swing rate = 50%: No swing; straight
Swing rate = 75% (51% or higher): The timing of even beat
notes is slightly delayed.
Swing rate = 25% (49% or lower): The timing of even beat notes
is slightly early.
Swing rate = 67%: The timing of even beat notes is moved to
the third beat of the triplets.
n Channels that do not contain any data are not displayed.
However, for some Songs, all channels (including the
channels that contain no data) may be displayed.
Channel Clear
This allows you to delete data of a single specified channel,
or of all 16 channels at once.
A
B
ChannelClear Execute?-->
Ch1
C
Default setting: Off
NO
YES
D
Setting range: Ch 1 – Ch 16, ALL (all channels)
Default setting: Ch 1
n Song data consists of 16 channels. Each instrument part is
assigned to a specific channel, so for this instrument, the
words “channel” and “track” have the same meaning.
86
CP300 Owner’s Manual
Settings for Song Recording and Playback—Song Settings
n Channels that do not contain any data are not displayed.
However, for some Songs, all channels (including the
channels that contain no data) may be displayed.
n When you clear all channels using the “ALL” parameter,
you can overwrite the Song. In this case, an empty Song
file having no channel data is saved.
From/To Repeat
This allows you to set the time signature of the click.
Specify the numerator of the time signature by using the
C [–][+] buttons and specify the denominator by using the
D [–][+] buttons. For example, to specify 3/4 time, use the
C [–][+] buttons to select “3” and the D [–][+] buttons to
select “4.”
A
This allows you to specify a section within a Song and play
it back repeatedly. The section can be specified freely (in
measures/beats), and playback repeats after it reaches the
point just prior to the beat specified as the end point.
If you start playing back a Song with “Repeat On” selected,
a lead-in count starts, followed by the repeated playback of
the specified part until you press the [STOP] button. If you
select “Repeat Off,” normal playback starts.
NO
C
TimeSignature
4/
NO
YES
4
C
D
Setting range for the numerator: 1 – 16
Setting options for the denominator: 2, 4, 8
Default setting: 4/4
Click Volume
B
RepeatOff
To 002:001
B
YES
D
This allows you to set volume of the click sound.
A
Reference
A
FromToRepeat
From 001:001
Time Signature
B
ClickVolume
Settings: RepeatOn, RepeatOff
NO
Default setting: RepeatOff
If you select “Repeat On,” use the C [–][+] and D [–][+] buttons
to specify the range to be repeated during Song playback.
n When you select another Song, the specified range is
automatically cancelled and the Repeat function is turned
off.
YES
100
C
D
Setting range: 0 – 127
Default setting: 100
Click Type
Song Repeat
This allows you to repeatedly play back all Songs or a single
Song selected from storage memory.
When you start playback, the CP300 plays the Song you
selected from the front panel, then starts repeat playback of
the specified Songs until you press the [STOP] button.
Press the [STOP] button to return to the top of the Song.
A
This allows you to select whether the click sound has a bell
accent, or plays only a click sound.
A
B
ClickType
NO
YES
BellOff
C
D
Setting range:
B
SongRepeat
Off
PresetSongs
NO
C
YES
BellOff
Click (standard click sound)
BellOn
Click and bell
D
Default setting: BellOff
Settings:
PresetSongs
All Preset Songs
All
All Memory Songs and Preset Songs
OneSong
One Song selected from the front panel
MemorySongs
All recorded Songs
Default setting: PresetSongs
CP300 Owner’s Manual
87
Connecting to a Computer and Other MIDI Devices
CAUTION
First, make sure that all volume settings are turned down all the way to the minimum. Then turn on the every
device in your setup in the order of MIDI master (controllers), MIDI slaves (receivers), then audio equipment
(mixers, amplifiers, speakers, etc.).
1
MUSIC PRODUCTION SYNTHESIZER
2
3
CP300
Audio equipment (first mixer,
then amplifier)
POWER
ON!!
MIDI master
Reference
When powering down the setup, first turn down the volume for each audio devices, then switch off each device in
the reverse order (first audio devices, then MIDI).
Connecting to External Audio Equipment
The CP300 has built-in speakers. You can also monitor the sound of the instrument by using external
equipment. Connect a set of headphones, powered speakers, or other playback equipment as required.
There are several methods of connecting to external audio equipment, as described in the following
illustrations. The following illustrations show various connection examples; use the one most similar to your
intended setup.
Connecting Stereo Powered Speakers
For optimum, accurate reproduction of the instrument’s rich sounds, effects and full stereo image, use a pair of
powered speakers. Connect the powered speakers to the OUTPUT L/MONO and R jacks on the rear panel.
Powered speaker (Left)
Powered speaker (Right)
OUTPUT L/MONO jack
OUTPUT R jack
Headphones
PHONES
jack
CP300
n When using just one powered speaker, connect it to the OUTPUT L/MONO jack on the rear panel.
n If you are connecting only to the L/MONO jack and want to use a Piano Voice, we recommend that you use the
Mono Piano 1 or Mono Piano 2 Voice for best results.
88
CP300 Owner’s Manual
Connecting to a Computer and Other MIDI Devices
Connecting to a Mixer
These are extra audio outputs in addition to the main OUTPUT L/R jacks.
The CP300 also features professional-use balanced XLR connectors for the OUTPUT L/R jacks. This type of
connector is used in professional studio equipment and installations.
OUTPUT L
OUTPUT R
Amplifier
OUTPUT L jack
OUTPUT R jack
Mixer
Headphones
Powered
speaker
(Right)
Powered
speaker
(Left)
CP300
Reference
PHONES
jack
n • Connecting a pair of headphones does not affect audio output from the OUTPUT L/R and OUTPUT L/
MONO, R jacks. You can adjust the volume of the external audio equipment, built-in speakers or headphones
with the [MASTER VOLUME] dial.
• The sound monitored through the headphones is identical to the sound of the OUTPUT L/R and OUTPUT L/
MONO, R jacks.
About the OUTPUT L/R jacks
These XLR connectors carry a balanced signal output, and are intended for use in professional studios
and installations. If the corresponding circuitry is designed properly, however, XLR-type connectors will
also handle unbalanced signals with no problem. Microphone cables usually have this type of connector,
as do the inputs and outputs of most professional audio gear.
Connecting to External Equipment
The CP300 also features a set of INPUT jacks. The stereo outputs from another instrument can be connected
to these jacks, allowing you to play the sound of an external instrument through the CP300’s speakers.
Connect the outputs from the other instrument to the INPUT L/MONO and R jacks on the rear panel.
INPUT L/MONO jack
INPUT R jack
OUTPUT L/MONO jack
OUTPUT R jack
MUSIC PRODUCTION SYNTHESIZER
CP300
External MIDI synthesizer/tone generator
The sound of an instrument connected to these INPUT jacks cannot be adjusted from the CP300. Any level
adjustments must be done from the instrument itself.
CP300 Owner’s Manual
89
Connecting to a Computer and Other MIDI Devices
Connecting to External MIDI Equipment
Using a standard MIDI cable (available separately), you can connect an external MIDI device, and control it
from the CP300. Likewise, you can use an external MIDI device (such as a keyboard or sequencer) to control
the sounds on the CP300. Below are several different MIDI connection examples; use the one most similar to
your intended setup.
n The CP300 cannot receive or transmit MIDI start (FAh), Continue (FBh), or Stop (FCh) messages.
Controlling from an External MIDI Keyboard
Use an external keyboard or synthesizer (such as the MOTIF ES) to remotely select and play the Voices of the
CP300.
MIDI IN
MIDI OUT
MUSIC PRODUCTION SYNTHESIZER
Reference
CP300
External MIDI synthesizer such as MOTIF ES
n The CP300 can playback commercially available Song data or Song data created for other instruments or on a
computer. For details about MIDI data compatibility, refer to page 100.
n In order to have an external MIDI device control separate parts of the CP300’s internal tone generator, you’ll need
to change the “MIDI In Channel” parameter in the MIDI Setting menu. For details, refer to page 65.
MIDI Transmit Channel and Receive Channel
Make sure to match the MIDI Transmit Channel of the external MIDI instrument with the MIDI
Receive Channel of the CP300. For details on setting the MIDI Transmit Channel of the external MIDI
instrument, refer to the Owner’s Manual of the MIDI instrument.
When setting the MIDI Receive Channel of the CP300, confirm the MIDI Receive Channel for each
part and change the settings of the desired parts, if necessary, to match the MIDI Transmit Channel
settings on the external MIDI instrument. (Refer to page 65.)
90
CP300 Owner’s Manual
Connecting to a Computer and Other MIDI Devices
Controlling an External MIDI Keyboard
This connection lets you play the sounds of an external MIDI tone generator (synthesizer, tone generator
module, etc.) from the keyboard of the CP300. Use this connection to play the sounds of the connected
instrument in a layer with the CP300, or use the sophisticated Zone functions (page 39) to set up splits in the
sounds.
MIDI IN
MIDI OUT
External MIDI keyboard or synthesizer,
such as the S/SY/EX series
CP300
Reference
Splitting the Sound between the CP300 and an External Tone Generator by MIDI
Channel
Using the connection example shown above, you can play both instruments and have them separately
sound different parts. To use this feature, you must set the CP300’s output channel and the external tone
generator’s receive channel to the same channel number. Set the MIDI Transmit Channel via the “MIDI
Out Channel” parameter in the MIDI Settings menu while turning on the power (page 65). While the
Master mode is turned on, set the MIDI Transmit Channel via the “MIDI Out Channel” parameter in
the Master Edit menu (page 55).
Controlling Another MIDI Device via MIDI THRU
MIDI THRU simply re-transmits the MIDI messages received via MIDI IN. In the example below, the MIDI
messages generated by playing an external keyboard are transmitted to an external tone generator via the MIDI
THRU connector on the CP300. The MIDI data of your performance on the CP300 are transmitted to an
external device via the MIDI OUT connector on the CP300.
MIDI OUT
MIDI OUT
MIDI IN
MIDI THRU
MIDI IN
MIDI IN
MUSIC PRODUCTION SYNTHESIZER
C
External MIDI tone
generator
External MIDI keyboard
CP300
External MIDI synthesizer
CP300 Owner’s Manual
91
Connecting to a Computer and Other MIDI Devices
Connecting to a Computer
Connecting this instrument to a computer via MIDI opens up a whole world of musical possibilities—such as
using sequencer software to record and play back compositions with the CP300 sounds.
In order to use the instrument with a computer via a USB connection, you will need to install an
appropriate USB-MIDI driver. You can download the proper driver from our website:
http://www.yamaha.co.jp/download/usb_midi/
Compatible versions for: Windows XP Professional/Home Edition/Me/2000/98, and Mac OS X 10.2 – 10.4.0
*This information applies to version 2.1.6 (Windows) and version 1.0.4 (Mac OS X). For the latest information,
check the web site above.
Using a USB Cable
MIDI messages can be transferred between the sequencer software and CP300 using the USB cable. However,
audio data cannot be transmitted or received via USB on the CP300.
Reference
USB cable
USB connector
CP300
Computer with a USB interface
When the USB connector is connected, the MIDI connectors cannot be used.
Precautions when using the USB connector
When connecting the computer to the USB connector, make sure to observe the following points. Failing
to do so risks freezing the computer and corrupting or even losing the data. If the computer or the
instrument freezes, turn the power to the instrument off or restart the computer.
CAUTION
• Before connecting the computer to the USB connector, exit from any power-saving mode (such as suspended, sleep, standby)
of the computer.
• Before turning on the power to the instrument, connect the computer to the USB connector.
• Execute the following before turning the power to the instrument on/off or plugging/unplugging the USB cable to/from the
USB connector.
- Quit any open applications (such as Voice Editor, Multi Part Editor, and sequencer software).
- Make sure that data is not being transmitted from the instrument. (Data is transmitted only by playing notes on the
keyboard or playing back a song.)
• While a USB device is connected to the instrument, you should wait for six seconds or more between these operations: (1)
when turning the power of the instrument off then on again, or (2) when alternately connecting/disconnecting the USB cable.
Selecting Voices from a Computer
You can select Voices on this instrument from your computer software by specifying the following MIDI
messages.
• Bank Select MSB
• Bank Select LSB
• Program Change
For details on what values are assigned to the Voice Bank/Number of this synthesizer, refer to the
“Program Change List” on page 105.
92
CP300 Owner’s Manual
Connecting to a Computer and Other MIDI Devices
Using Local On/Off when connected to a computer
When connecting the CP300 to a computer, the keyboard performance data is generally sent to the computer,
and then returned from the computer to play the tone generator block on the CP300. If the Local Control
parameter in the MIDI Settings menu is set to “on,” a “double” sound may result, since the CP300 tone
generator is receiving performance data from both the keyboard directly and the computer.
Use the setting suggestions below as a guideline; specific instructions may differ depending on your computer
and the software used.
When MIDI Echo (MIDI Thru) is enabled on the software/computer:
Computer (SQ01, etc.)
USB connector
CP300
In
Out
Out
Tone generator
Keyboard
Local off
In
[MIDI SETTING] Local Control = Off
Echo back = on
Reference
n When transmitting or receiving System Exclusive data (such as with the Bulk Dump function), use the setting
example below, making sure that MIDI Echo on the computer software is set to “off.”
When MIDI Echo (MIDI Thru) is disabled on the software/computer:
Computer (SQ01, etc.)
USB connector
Out
CP300
In
Tone generator
Keyboard
Local on
[MIDI SETTING] Local Control = On
Echo back = on
* MIDI Echo is a function on sequencers that takes any data received via the MIDI IN and “echoes” it (or sends it as is) through the MIDI
OUT. In some software, this function is also called “MIDI Thru.”
n For details about MIDI Echo, refer to the owner’s manual of your particular software.
CP300 Owner’s Manual
93
Message List
Appendix
Message List
The messages are listed in alphabetical order.
Message
Description
Bulk data reception has been completed.
BulkDataReceiving
Completed
This is shown following the “Bulk Data Receiving Voice” message. This indicates that the
instrument finished receiving bulk data, and that you can go on to the next step.
Bulk data reception has failed.
BulkDataReceiving
Error
Check that the cable connection is secure and try again.
The instrument is receiving bulk data while this message is displayed.
BulkDataReceiving
BulkDump
Wait until the message closes, then go on to the next step.
Error
Appendix
Canceled
Completed
DataFmtErr
DuplicatedName
Execute?-->
Executing
FactorySet
Completed
MemoryFileExcluded
FactorySet
Completed
MemoryFileIncluded
94
CP300 Owner’s Manual
The instrument failed to transmit the bulk data.
If this message appears, make sure that the power of your computer has not been turned
off, that the cable is connected correctly, and that the driver on your computer is functioning
correctly. Then try transmitting the data once again.
This is shown when the operation has been canceled.
The operation is completed.
This is shown following the “Executing” message. The instrument’s internal processing is
complete. You can go on to the next step.
The file format is invalid.
This message appears when the Performance file selected via “Load From Mem.” (page 79)
is invalid and cannot be called up.
The Song name or Performance name is duplicated.
You tried to save a Song file after changing its name using the “Rename Song” (page 83), or
a Performance file after changing its name using the “Rename File” (page 80) parameter,
but a Song or Performance with the same name already exists in memory. The instrument
returns to the previous display after three seconds. Rename the Song correctly.
Do you wish to execute the operation?
This message prompts you to execute a file-related operation. Press the B [+ (YES)] button
to save the settings. Press the B [– (NO)] or [EXIT] button to cancel.
The instrument is processing the data internally.
Wait until the message closes, then proceed to the next step.
The factory default settings, excepting files stored to storage memory (refer to
“Factory Set” on page 71), have been restored.
This message also appears if you press and hold down the C7 key and turn on the power to
the instrument (page 17).
The factory default settings, including files stored to storage memory (refer to
“Factory Set” on page 71), have been restored.
This message also appears if you press and hold down the C7 and Bb6 keys and turn on the
power to the instrument (page 17).
Message List
Message
Description
FlashMemoryLifeTime
Exit-->
The instrument’s flash memory (storage memory) has expired.
Consult your Yamaha dealer. If this message appears, the instrument will not be able to back
up the Songs, Performance files and settings in memory. Press the [EXIT] button to return to
the original display.
There is a problem with the USB connector.
HostError
The power to the computer is turned off, the cables are connected incorrectly, or the driver
or MIDI application on the computer is working incorrectly. In this situation, turn the power off
to both the instrument and the computer, and check the cable connection. Then, turn on the
power to the computer and the instrument in this order and check to see if the driver and
MIDI application on the computer work properly.
This message is also shown if the USB cable is connected to the instrument without being
connected to your computer. When you wish to use the instrument alone, turn off the power
of the instrument, disconnect the USB cable from the instrument, then turn the power on
again. If the cable is left connected in this condition, the instrument may not function
properly.
LastPowerOffIllegal
MemoryFileErrorRecovered
LastPowerOffIllegal
MemoryFileErased
The power was incorrectly turned off the previous time. The instrument is
checking the internal memory.
You turned off the power to the instrument while it was writing data to storage memory. This
message appears next time you turn on the power. The internal memory is being checked
while this message is displayed. If it has been confirmed that any files in the storage
memory are corrupted, all the files will be deleted.
Some files in the storage memory have been restored.
This message appears following the message “Last Power Off Illegal / Memory File
Checking,” indicating that the instrument recovered as much data in the storage memory as
possible.
Files on the storage memory have been deleted.
Appendix
LastPowerOffIllegal
MemoryFileChecking
This message appears following the message “Last Power Off Illegal / Memory File
Checking,” indicating that the instrument could not recover data in the storage memory and
that all memory files were deleted.
A memory problem has occurred.
MemoryError
While a Song or a Performance file was being loaded, the instrument detected defects in
memory. Reset the instrument to its normal (factory default) settings with “Memory File
Included” (page 71) after you back up all Song data.
MemoryError
MemoryFull
NoSong
There may be a memory problem.
1. This message indicates that there may be a problem with the memory when selecting a
Song or Performance file. If the message appears repeatedly when you continue using
the instrument, back up the Song data, then restore the default setting by using “Memory
File Included” in “Factory Set” (page 71).
2. This message will appear if a different “Character Code” (page 84) is selected than was
when you assigned the Performance file name. In this case, switch the “Character
Code,” re-select the Performance file.
There is no more available space in storage memory.
There is not enough memory space left and you cannot save any more Songs or
Performance files. Delete some Songs or Performance files in the storage memory (pages
80, 83), then save the new data to memory.
There is no Song to be saved.
This message will appear if there is no Song for the “Save To Memory” (page 82) operation
to save. In this case, no Song will be saved.
There is no file to be deleted.
NoFileToDelete
You tried to delete a file that does not exist in the storage memory. You cannot delete the file.
There is no Song to be deleted.
NoSongToDelete
You tried to delete a Song that does not exist in the storage memory. The Song cannot be
deleted.
CP300 Owner’s Manual
95
Message List
Message
Description
OverWrite?
Do you want to overwrite the data?
This message prompts you to select whether you wish to overwrite the existing data with
new data. Press the B [+ (YES)] button to allow overwriting. Press the B [– (NO)] button to
cancel.
Please wait.
PleaseWait
You tried to start playing a Song or perform another operation right after selecting the Song.
Wait until the message closes.
ProtectedFile
ProtectedSong
Set?-->
SongChanged Save?
This is a protected file.
You tried to copy or delete data in internally-protected files (such as commercially available
music data). You cannot write to, copy, or delete such files.
This is a protected Song.
This message appears when you try to change the name of an internally-protected Song
(Preset Song). You cannot change the name of such Songs.
Is the setting maintained?
This message prompts you to select whether you wish to save the edited settings or not.
Press the B [+ (YES)] button to save the settings. Press the [EXIT] button to cancel.
The Song has been changed. Do you wish to save the Song?
You tried to perform another operation before saving the recorded Song to storage memory.
If you continue the operation, the recorded Song will be lost. To delete the new recording,
press the B [– (NO)] button. To keep the recording, press the B [+ (YES)] button. The “Save
To Memory” (page 82) parameter is shown in the display. Save the Song then try the
operation again.
An error has been found in the Song data.
Appendix
SongError
SongError
1. The instrument has found some defects in the selected (or playing) Song. Select the
Song and play it again. If you still see this message, the Song data may be damaged.
2. This message will appear if a different “Character Code” (page 84) is selected than was
when you assigned the Song name. In this case, switch the “Character Code,” re-select
the Song, and play it back.
The Song data is too large.
SongTooBig
1. The Current memory space has become full during recording. Recording stops
automatically. The data recorded up to that point remains. This message also appears
when you try to enter recording mode to perform additional recording but the Song data
has already filled the current memory. In this case, you cannot perform additional
recording. Use the “Channel Clear” parameter (page 86) to delete unnecessary tracks (if
any) to make more room in memory.
SongTooBig
2. The size of the selected Song is larger than the current memory. The instrument cannot
load/play the selected Song. Select another Song.
3. This message is shown when you edit a Song if that Song is larger than the capacity of
the current memory. This Song cannot be edited on the instrument.
Start?-->
Sure?-->
Transmitting
Transmitting
Completed
96
CP300 Owner’s Manual
Do you wish to start the operation?
This message prompts you to start the operation. To start, press the B [+ (YES)] button.
Press the [EXIT] button to cancel the operation.
Are you sure?
This message prompts you to confirm the execution. Press the B [+ (YES)] button to
continue. Press the B [– (NO)] button to cancel.
MIDI bulk data is being transmitted.
This message appears when the instrument receives a bulk request from a computer. This
message appears while the bulk data is being transmitted. Wait until the message closes,
then go on to the next step. Please wait.
Bulk data transmission has been completed.
This is shown following the “Transmitting” message. It is displayed when the transmission of
the bulk data has been completed. You can go on to the next step.
Message List
Message
Description
MIDI Bulk data is being transmitted.
Transmitting
Error
This message appears when the instrument receives a bulk request from a computer. The
instrument has failed to transmit Voice bulk data.
Check the cable connection and repeat the procedure from the beginning.
The Song name or Performance file name is not appropriate.
1. This message appears when you have used a period or space at the beginning of a
Song name/Performance file (while handling a Song/Performance file), or you have tried
to change a Song name by including a character (or characters) not supported by the
instrument. The instrument returns to previous display after three seconds. Make sure to
enter a valid name.
2. This message will appear if a different “Character Code” (page 84) is selected than was
when you assigned the Song name or Performance file name. In this case, switch the
“Character Code,” re-select the Song or Performance file.
Appendix
WrongName
CP300 Owner’s Manual
97
Troubleshooting
Problem
Solution
The power of the instrument does
not turn on.
The instrument has not been plugged in
properly.
Securely insert the female plug into the
socket on the instrument, and the male plug
into a proper AC outlet (page 11).
A click or pop is heard when the
power is turned on or off.
This is normal when electrical current is
being applied to the instrument.
This is normal.
Noise is heard from the instrument's
speakers.
The noise may be due to interference
caused by the use of a mobile phone in
close proximity to the instrument.
Turn off the mobile phone, or use it further
away from the instrument. Using a mobile
phone in close proximity to the instrument
may produce interference.
The overall volume is too low, or
there is no sound at all.
The [MASTER VOLUME] (page 13) may be
set too low.
Raise the [MASTER VOLUME] level.
The [ZONE CONTROL] (page 28) may be
set too low.
Raise the [ZONE CONTROL] slider.
Speaker setting may be off.
Turn on the [SPEAKER] button (page 52).
“Local Control” (page 65) may be set to off.
Set “Local Control” to on.
“Internal TG” (page 55) may be set to off.
Set “Internal TG” to on.
The pedal or the Modulation wheel is set to
minimum, when “Expression” is assigned to
the foot controller or Modulation wheel.
Change the position of the pedal or
Modulation wheel.
“Expression” may have been assigned to
one of the connected footswitches.
Assign any function other than “Expression”
to the footswitch.
The gain setting of the Master EQ (page 36)
may be low.
Raise the gain of the Master EQ.
The gain of the Part EQ (page 36) may be
low.
Raise the gain of the Part EQ.
“Volume” may have been assigned to the
[ZONE CONTROL] slider while the Master
mode is turned on, the [ZONE CONTROL]
may be set too low.
Raise the [ZONE CONTROL] slider.
The keyboard volume is low.
The volume level for the keyboard
Performance may be set too low.
Raise any of the [ZONE CONTROL] slider.
The Song playback volume is low.
The volume of the Song playback may be
set too low.
Raise the [SONG VOLUME] slider.
The speakers do not switch off when
a pair of headphones is connected.
Speaker setting may be On.
Set the Speaker setting to Off.
The pitch and/or tone of the Piano
Voices in certain ranges do not
sound right.
The Piano Voices attempt to precisely
simulate actual piano sounds. However, as
a result of sampling algorithms, overtones in
some ranges may sound exaggerated,
producing a somewhat different pitch or
tone.
This is normal.
Mechanical noise is heard during
Performance.
The keyboard mechanism of this instrument
simulates the keyboard mechanism of an
actual piano. Mechanical noise is also heard
on a piano.
This is normal.
The buttons do not respond.
While you are using a function, some
buttons not used for the function are
disabled.
If a Song is playing or recording, stop
playback or recording. Otherwise, press the
[EXIT] button to return to the main display,
and then perform the desired operation.
The Panel Lock function is effective.
Rapidly press the [PANEL LOCK] button
twice to cancel the Panel Lock.
Appendix
98
Possible causes
CP300 Owner’s Manual
Troubleshooting
Possible causes
Solution
The sound sustains and does not
decay while pressing the pedal to
which the sostenuto function is
assigned.
For Voices in the ORGAN, STRINGS,
CHOIR, PAD, and XG groups, the sound
continues sustaining while you are holding
down the sostenuto pedal.
This is normal.
Higher or lower notes do not sound
correctly when the transpose or
octave setting is made.
The setting range for the transposition and
octave setting is C-2 – G8. (With the normal
setting, the 88 keys of this instrument cover
the range of A-1 – C7.) If the lowest key is
set to a note lower than C-2, it will produce a
sound one octave higher. If the highest key
is set to a note higher than G8, it will
produce a sound one octave lower.
This is normal.
The tempo does not change even
though the Song was recorded with
tempo changes.
Depending on the timing of tempo changes,
the tempo change may not have been
recorded. In this case, the recording will be
played back at the original tempo. Make
tempo changes when the recording track is
selected and a red track indicator is
flashing. The same method applies to
editing the tempo after recording.
This is normal. Check the location of the
tempo change.
Performance in Dual or Split mode
is not recorded, and one or more
tracks have been unexpectedly
deleted.
For Dual or Split mode recording, the
recording track for the Layer part Voice or
the Left part Voice is automatically assigned
(page 48). Therefore, if the track already has
data, the data will be overwritten during
recording. Also, the actual process of
switching to Dual mode or Split mode in the
middle of the Song is not recorded.
Therefore, the notes you played with the
Layer part Voice or the Left part Voice are
not recorded.
This is normal.
Cannot change the time signature in
the Song after recording.
The time signature cannot be changed in
the middle of the measure.
Press the [STOP] button to locate the top of
the Song, use the B [– (NO)][+ (YES)]
buttons to locate the measure in which you
wish to change the time signature, and then
change it.
The Song title is not correct.
The “Character Code” setting may be
different than that used when you named the
Song.
Use the “Character Code” parameter
(page 84) in the [SONG FILE] button to
change the setting.
The Performance title is not correct.
The “Character Code” parameter setting
(page 84) has been changed from the one
set when naming the Performance file.
Make sure that the “Character Code”
parameter is set to the same one as set
when the Performance file was named.
CP300 Owner’s Manual
Appendix
Problem
99
MIDI Data Compatibility
The data and the MIDI device must match in regards to the items below.
Voice allocation format
With MIDI, Voices are assigned to specific numbers, called “program numbers.” The numbering standard
(order of Voice allocation) is referred to as the “Voice allocation format.” Voices may not play back as expected
unless the Voice allocation format of the Song data matches that of the compatible MIDI device used for
playback.
GM System Level 1
This is one of the most common Voice allocation formats. Many MIDI devices are compatible with GM
System Level 1. Most commercially available music data is created as Format 0 “GM System Level 1.”
XG
XG is a major enhancement of the GM System Level 1 format, and was developed by Yamaha specifically
to provide more Voices and variations, as well as greater expressive control over Voices and effects, and to
ensure compatibility of data well into the future. Song data recorded on the instrument using Voices in
the XG category is XG-compatible.
Appendix
100
CP300 Owner’s Manual
Factory Setting List
Voice settings [VOICE EDIT]
All the Voice settings differ depending on the current Voice.
MIDI settings [MIDI SETTING]
Settings
Value
Page
MidiOutChannel
Setting the MIDI transmit channel
Main: Ch 1
Left: Ch 2
Layer: Ch 3
Left Layer: Ch 4
65
MidiInChannel
Setting the MIDI receive channel
Ch 1 – 16: Song
Ch 17: Keyboard
Ch 18: Main
Ch 19: Left
Ch 20: Layer
Ch 21: Left Layer
Ch 22 – 32: Off
65
LocalControl
Turning local control on/off
On
65
MidiOutSelect
Selecting performance from the keyboard or Song data for
MIDI transmission
Keyboard
65
ReceiveParameter
Selecting the types of data received via MIDI
All data: On
66
TransmitParameter
Selecting the types of data transmitted via MIDI
All data: On
66
IntialSetup
Transmitting the initial settings on the panel
—
66
BulkDump
Executing Voice data bulk dump
Current
66
Appendix
Parameter name
Other settings [OTHER SETTING]
Parameter name
Settings
Value
Page
TouchResponse
Selecting the touch response
Medium
68
Tune
Fine tuning the pitch
A3 = 440.0 Hz
68
PianoTuningCurve
Selecting a tuning curve for a Piano Voice
Stretch
68
Scale
Selecting a scale
Equal
68
SplitPoint
Specifying the Split Point (Main)
F#2
69
SplitPoint2
Specifying the Split Point 2 (Layer)
F#2
69
Transpose
Changing the key
Keyboard = 0
Song = 0
69
SoftPedalDepth
Adjusting the depth of the Soft pedal
5
69
StringResonanceDepth
Setting the depth of String Resonance
5
69
SustainSamplingDepth
Setting the depth of Sustain Sampling for the Sustain pedal
5
69
KeyOffSamplingDepth
Specifying the volume of the Key-off sound
5
70
VibraphonePedalMode
Selecting a pedal function for Vibraphone Voice
PianoLike
70
PedalPlay/Pause
Assigning the SONG [PLAY/PAUSE] function to the pedal
All pedals: Off
70
PedalType
Selecting a pedal type
Pedal 1, Pedal 2, Pedal
3: Make; Pedal 4: Break
70
CP300 Owner’s Manual
101
Factory Setting List
Parameter name
Settings
Value
Page
HalfPedalPoint
Setting the point at which the sustain pedal starts to affect
the sound
0
70
PitchBendRange
Setting the Pitch Bend range
2
70
EqualizerLock
Locking the Master Equalizer settings
On
71
MemoryBackUp
Selecting items saved at shutdown
Transpose,
Main/Left Layer,
OtherSetting: Off,
Others: On
71
FactorySet
Restoring the default settings
MemoryFileExcluded
71
Master settings [MASTER EDIT]
Parameter name
Settings
Value
Page
Assigning a function to the [ZONE CONTROL] slider
VOLUME
54
SendBankMsb
Setting the MSB of the Send Bank Select message
0
54
SendBankLsb
Setting the LSB of the Send Bank Select message
0
54
SendPG#
Setting the Program Change message
1
54
Octave
Setting the octave of the external tone generator
0
55
InterITG
Turning the internal tone generator on/off
On
55
MidiOutChannel
Setting the MIDI transmit channel when the Master mode is
turned on
Zone 1: Ch 1,
Zone 2: Ch 2,
Zone 3: Ch 3,
Zone 4: Ch 4
55
Appendix
Slider
Settings for Song recording and playback [SONG SETTING]
Parameter name
Quantize
Settings
Correcting note timing.
Determining how strongly the notes will be quantized.
SwingRate
102
Value
Off
Page
86
50%
QuickPlay
Specifying whether playback starts immediately along with
the first voicing
On
86
ChannelListen
Auditioning the channels
Ch 1
86
ChannelClear
Deleting data from each channel
Ch 1
86
FromToRepeat
Specifying the range and playing back repeatedly
RepeatOff
87
SongRepeat
Playing back a Song/all Songs repeatedly
PresetSongs
87
TimeSignature
Setting the Click time signature
4/4
87
ClickVolume
Setting the Click volume level
100
87
ClickType
Setting the Click bell sound
BellOff
87
CP300 Owner’s Manual
Voice group
Voice name
GrandPiano1
GrandPiano2
Mono Piano
E.Piano1
E.Piano2
E.Piano3
Stereo
sampling
Touch
Sense
Dynamic
sampling
Key-off
samples
String
resonance
Voice description
Grand Piano 1
Ø
Ø
Ø
Ø
Ø
This sound was sampled from a full concert
grand piano. Three stages of dynamics were
sampled, and no effort has been spared in
making the sound virtually identical to that of an
acoustic piano. Even the tonal changes
produced by the damper pedal and the subtle
sounds of releasing a key are reproduced. The
sympathetic vibration (string resonance) that
occurs between the strings of an acoustic piano
has also been simulated. Suitable not only for
classical compositions but also for piano pieces
of any style.
Mellow Piano 1
Ø
Ø
Ø
Ø
Ø
A warm and mellow piano sound. Ideal for
classical music.
Rock Piano
Ø
Ø
Ø
Ø
Ø
A bright-sounding piano. Ideal for rock styles.
HonkyTonk Piano
Ø
Ø
Ø
Ø
Ø
A honky-tonk style piano. Enjoy a tonal
character that is quite different than a grand
piano.
Grand Piano 2
Ø
Ø
–
–
–
A spacious and clear piano sound with a bright
resonance. Ideal for popular music.
Mellow Piano 2
Ø
Ø
–
–
–
A mellow piano sound with a different character
than Mellow Piano 1.
Mono Piano 1
–
Ø
Ø
–
–
The sound of a mono piano. Good for ensemble
performance.
Mono Piano 2
–
Ø
–
–
–
A mono piano sound with a different character
than Mono Piano 1.
Comp. Piano 1
–
Ø
Ø
–
–
A mono piano sound with compression effect.
Comp. Piano 2
–
Ø
–
–
–
A mono piano sound with a different character
than Comp. Piano 1.
Chorus E.Piano
–
Ø
Ø
Ø
–
The sound of an electric piano that generates
sound by striking metal tines with a hammer.
Softly played notes will have a mellow character,
and strongly played notes will sound more
forceful. A chorus effect is applied to create
warmth.
Phaser E.Piano
–
Ø
Ø
Ø
–
A distinctive phaser effect makes this ideal for
fusion styles.
AutoPan E.Piano
–
Ø
Ø
Ø
–
An electric piano with a characteristic panning
effect.
Standard E.Piano
–
Ø
Ø
Ø
–
A straightforward electric piano sound with
reverb as the only effect.
DX E.Piano 1
Ø
Ø
Ø
–
–
The sound of an electronic piano as simulated
by an FM synthesizer such as the DX7.
Differences in playing dynamics will affect the
tone. Ideal for popular songs.
DX E.Piano 2
–
Ø
–
–
–
An FM synthesizer electronic piano sound using
a different algorithm than DX E.Piano 1, with a
bright sounding character.
Synth Piano
–
Ø
–
–
–
This Voice simulates the electric piano sound
produced by synthesizers in popular music. It
also goes well with the acoustic piano sound.
Tremolo Vintage
E.P.
–
Ø
Ø
–
–
The sound of an electric piano of a different type
than E.Piano 1, often used in rock and popular
music.
Vintage E.Piano
–
Ø
Ø
–
–
An electric piano sound with a vintage
character, and reverb as the only effect.
Amp.Sim. Vintage
E.P.
–
Ø
Ø
–
–
The sound of an electric piano distorted by an
amp simulator effect. Ideal for rock music.
CP300 Owner’s Manual
Appendix
Voice List
103
Voice List
Voice group
Clavi.
Vibraphone
Organ1
Organ2
Appendix
Harpsichord
Strings
Choir/Pad.
104
Voice name
Stereo
sampling
Touch
Sense
Dynamic
sampling
Key-off
samples
String
resonance
Voice description
Phaser Clavi.
–
Ø
–
Ø
–
This is the Voice of a keyboard that produces
sound by striking the strings with magnetic
pickups. This funky sound is popular in
contemporary soul and R&B music. Because of
its unique structure, the instrument produces a
peculiar sound when you release the keys.
Clavi. 1
–
Ø
–
Ø
–
A struck-string keyboard instrument with
electromagnetic pickups. A straightforward
sound with only reverb applied.
Wah Clavi.
–
Ø
–
Ø
–
Includes a distinctive wah effect.
Clavi. 2
–
Ø
–
Ø
–
A different type of Clavi. 1 sound.
Vibraphone
Ø
Ø
Ø
–
–
Vibraphone played with relatively soft mallets.
The tone becomes more metallic the harder you
play.
Marimba
Ø
Ø
–
–
–
A marimba sound, sampled in stereo for
spaciousness and realism.
Celesta
Ø
Ø
Ø
–
–
The sound of a celesta—a percussion
instrument in which hammers strike metallic
bars to produce sound.
Jazz Organ
–
–
–
–
–
The sound of a “tonewheel” type electric organ.
Often heard in jazz and rock idioms.
Theater Organ
–
–
–
–
–
A bright electric organ sound.
Rock Organ
–
–
–
–
–
An aggressive electric organ sound, ideal for
rock.
Draw Organ
–
–
–
–
–
A standard electric organ sound.
Pipe Organ
Principal
Ø
–
–
–
–
This Voice features the combination of pipes
(8'+4'+2') of a principal (brass instrument)
organ. It is suitable for Baroque church music.
Pipe Organ Tutti
Ø
–
–
–
–
This Voice features a full coupler of a pipe
organ, famous for the sound used in Toccata
and Fugue in D Minor by Bach.
Pipe Organ Flute
Ø
–
–
–
–
A pipe organ sound that combines flute-type
(woodwind type) stops of different pitches
(8'+4'). This is a gentle sound that is ideal for
accompanying hymns.
Harpsichord 8
Ø
–
–
Ø
–
The sound of the instrument frequently used in
baroque music. Variations in playing touch will
not affect the volume, and a characteristic
sound will be heard when you release the key.
Harpsichord 8'+4
Ø
–
–
Ø
–
A harpsichord with an added upper octave.
Produces a more brilliant sound.
Strings
Ø
Ø
–
–
–
Stereo-sampled, large-scale strings ensemble
with realistic reverb. Try combining this Voice
with piano in the Dual mode.
Synth Strings
Ø
Ø
–
–
–
A bright and spacious strings sound. Suitable
for sustained parts in the background of an
ensemble.
Slow Strings
Ø
Ø
–
–
–
The sound of a string ensemble, with a slow
attack. Suitable for use in Dual mode with
GRAND PIANO or E.PIANO.
Choir
–
Ø
–
–
–
A big, spacious choir Voice. Perfect for creating
rich harmonies in slow pieces.
Slow Choir
–
Ø
–
–
–
The sound of a choir with a slow attack. Suitable
for use in Dual mode with GRAND PIANO or
E.PIANO.
Scat
–
Ø
Ø
–
–
You can enjoy jazz “scatting” with this Voice.
Depending on how hard and what note range
you play, different sounds will be produced.
Synth Pad 1
–
Ø
–
–
–
A warm, mellow, and spacious synth sound.
Ideal for sustained parts in the background of
an ensemble.
CP300 Owner’s Manual
Voice group
Voice name
Stereo
sampling
Touch
Sense
Dynamic
sampling
Key-off
samples
String
resonance
Voice description
Choir/Pad.
Synth Pad 2
–
Ø
–
–
–
A clear and spacious synth sound. Ideal for
sustained parts in the background of an
ensemble.
Guitar
Nylon Guitar
Ø
Ø
Ø
–
–
A warm and natural nylon-string guitar sound.
Enjoy the atmosphere it adds to a quiet song.
Steel Guitar
–
Ø
–
–
–
A bright steel guitar sound. Ideal for popular
music.
Wood Bass
–
Ø
–
–
–
The sound of a finger-plucked upright bass.
Frequently used in jazz and Latin music.
Bass&Cymbal
–
Ø
–
–
–
The sound of a cymbal has been layered onto
the bass. Effective when used for jazz walkingbass lines.
Electric Bass
–
Ø
–
–
–
The sound of an electric bass. Frequently used
in jazz, rock, and popular music.
Fretless Bass
–
Ø
–
–
–
The sound of a fretless bass. Suitable for styles
such as jazz and fusion.
Bass
Voice group
GrandPiano1
GrandPiano2
Mono Piano
E.Piano1
E.Piano2
E.Piano3
Clavi.
Vibraphone
Voice name
Bank
MSB
Bank
LSB
P.C.#
Voice group
Grand Piano 1
0
122
1
Mellow Piano 1
0
123
1
Rock Piano
0
122
3
HonkyTonk Piano
0
122
4
Draw Organ
0
125
17
Grand Piano 2
0
112
1
Pipe Organ Principal
0
123
20
Organ1
Organ2
Voice name
Bank
MSB
Bank
LSB
P.C.#
Jazz Organ
0
122
17
Theater Organ
0
124
17
Rock Organ
0
122
19
Mellow Piano 2
0
114
1
Mono Piano 1
0
123
2
Mono Piano 2
0
114
2
Comp. Piano 1
0
124
2
Comp. Piano 2
0
116
2
Chorus E.Piano
0
122
5
Synth Strings
0
122
51
Phaser E.Piano
0
124
5
Slow Strings
0
122
50
AutoPan E.Piano
0
125
5
Choir
0
122
53
Standard E.Piano
0
126
5
Slow Choir
0
123
53
DX E.Piano 1
0
122
6
Scat
0
122
54
Harpsichord
Strings
Choir/Pad.
Pipe Organ Tutti
0
122
20
Pipe Organ Flute
0
124
20
Harpsichord 8'
0
122
7
Harpsichord 8'+4'
0
123
7
Strings
0
122
49
DX E.Piano 2
0
123
6
Synth Pad 1
0
122
90
Synth Piano
0
122
89
Synth Pad 2
0
122
92
Nylon Guitar
0
122
25
Steel Guitar
0
122
26
Wood Bass
0
122
33
Tremolo Vintage E.P.
0
123
5
Vintage E.Piano
0
121
5
Amp.Sim.Vintage E.P.
0
120
5
Phaser Clavi.
0
124
8
Clavi. 1
0
122
8
Wah Clavi.
0
123
8
Clavi. 2
0
125
8
Vibraphone
0
122
12
Marimba
0
122
13
Celesta
0
122
9
Guitar
Bass
XG
Bass&Cymbal
0
124
33
Electric Bass
0
122
34
Fretless Bass
0
122
36
480 Voices
–
–
–
Appendix
Program Change List
P.C.# = Program Change number (1-128)
When you specify a program change as a number in the range of 0-127, specify a number that is one less than the program number listed
below. For example, to specify program number 128, you would actually enter program change 127.
For details about XG Voices, refer to the XG Voice List (page 108).
CP300 Owner’s Manual
105
Preset Performance List
Number
Performance name
Type
Voices used
Main
Appendix
106
Layer
Performance discription
Left
Left Layer
A01
Piano+Pad
Dual
GrandPiano1
WarmPad
Grand piano layered with a
warm-sounding pad. Usable in
a variety of situations from rapid
passages to ballads.
A02
Piano+E.Piano
Dual
GrandPiano1
ChorusE.P.
Widely-used layered sound with
piano and electric piano. Ideal
for 80’s pop.
A03
Piano+DX E.P.1
Dual
GrandPiano1
DX E.Piano1
Widely-used layered sound with
piano and DX electric piano.
Enjoy harmonies with the
sparkling electric piano.
A04
Piano+DX E.P.2
Dual
GrandPiano2
DX E.Piano2
Another type of layered piano
and DX electric piano.
A05
Piano+SoftStr
Dual
GrandPiano2
S.SlwStr
Piano layered with soft strings.
A06
HonkyTonkPiano
Dual
GrandPiano1
GrandPiano1
Honky-tonk piano that simulates
slight detuning.
A07
E.Piano+Pad
Dual
AutoPanE.P.
SynthPad1
Auto-panned electric piano
layered with a soft pad.
Beautifully spacious stereo
spread.
A08
E.Piano+DX E.P.
Dual
StandardE.P
DX E.Piano1
Layered electric piano and DX
electric piano.
A09
E.Piano+SlowStr
Dual
ChorusE.P.
SlowStrings
Chorused electric piano layered
with slow attack strings.
A10
E.Piano+
Vintage E.P.
Dual
StandardE.P
VintageE.P.
Standard electric piano layered
with vintagetype electric piano.
A11
DX E.P.+SoftStr
Dual
DX E.Piano2
S.SlwStr
DX electric piano layered with
soft strings.
A12
DX E.P.+
SynthPiano
Dual
DX E.Paino2
SynthPiano
DX electric piano layered with
synth piano.
A13
PipeOrgan+Choir
Dual
PipeOrganTu
Choir
Magnificent layered sound with
pipe organ and chorus.
A14
Strings+Choir
Dual
Strings
Choir
Classical layered sound with
strings and chorus.
A15
Orchestral Harp
Dual
NylnHarp
Harp
Beautiful layered sound of two
harps, slightly delayed.
A16
PolySynthPad
Dual
PolySyPd
NewAgePd
Dense and rich motion pad.
Key-on modifies the sound.
B01
WoodBass/
GrandPiano
Split
GrandPiano1
Wood Bass
Standard wood bass split with
piano. Ideal for playing jazz by
yourself.
B02
WoodBass/
NylonGuitar
Split
Nylon Guitar
Wood Bass
Nylon-string guitar split with
wood bass.
B03
WoodBass/
VibraPhone
Split
Vibraphone
Wood Bass
Standard wood bass split with
vibraphone.
B04
Bass+Cym/
JazzOrgan
Split
JazzOrgan
Bass & Cymbal
Play rhythm with bass and
cymbal in the left hand, and
solo organ in the right hand.
B05
E.Bass/PhaserE.P.
Split
Phaser E.Piano
Electric Bass
Electric piano with phaser
(typical of 70’s fusion), split with
electric bass.
B06
Bass+Cym/Scat
Split
Scat
Bass & Cymbal
Play scat in the right hand, and
bass and cymbal in the left.
Scat sounds are velocityswitched.
CP300 Owner’s Manual
Preset Performance List
Performance name
Type
Voices used
Main
B07
Organ Upper/Lower
Dual+Split
JazzOrgan
B08
E.Piano/GrandPiano
Split
B09
Layer
SoloSine
Performance discription
Left
Left Layer
Jazz Organ
Simulates a dual-manual organ.
Play chords in the left hand, and
solo with the right.
GrandPiano1
Phaser E.Piano
Play chords in the left hand on
an electric piano with phaser
applied, and piano solo in the
right.
JazzOrg/GrandPiano Split
GrandPiano1
Jazz Organ
Play organ backing in the left
hand, and piano solo in the
right.
B10
SynBass/SynBrass
Dual+Split
SynBrss1
SynBass1Dark
Play synth bass in the left hand,
and bright synth brass in the
right.
B11
Delay E.Piano
Single
Standard
E.Piano
Electric piano with delay
applied to create a sense of
space.
B12
Room Piano
Single
GrandPiano1
Piano that sounds as if heard at
a distance in a spacious room.
B13
Old piano
Single
GrandPiano2
Simulation of a piano sound
heard on an old record. Distorts
slightly as you play harder.
B14
Baroque Ensemble
Dual+Split
Hc8'+4'
PipeOrganP
Strings
Choir
Play strings and chorus in the
left hand, and harpsichord and
pipe organ in the right.
B15
AOR Split
Dual+Split
GrandPiano2
SynthPad1
E.Bass
MuteGtr
Rich sound that lets you play
muted guitar and bass in the left
hand, and piano and pad in the
right.
B16
Drum Kit
Drm
StandardKit1
SynBrss1
The CP300 provides highquality drum sounds as well as
piano sounds. Try out your
drumming skills!
Appendix
Number
The 32 Performances in variations C, D use the Grand Piano 1 Voice.
CP300 Owner’s Manual
107
XG Voice List
Bank Select MSB=00
KSP
Instrument
Group
Piano
Chromatic
Percussion
Organ
Guitar
Bass
Strings
Ensemble
Brass
Appendix
Reed
Pipe
Synth Lead
Synth Pad
Synth Effects
Ethnic
Percussive
Sound Effects
Pgm#
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
Bank 0
Bank Select LSB=00
Acoustic Grand Piano
Bright Acoustic Piano
Electric Grand Piano
Honky-tonk Piano
Electric Piano 1
Electric Piano 2
Harpsichord
Clavi
Celesta
Glockenspiel
Music Box
Vibraphone
Marimba
Xylophone
Tubular Bells
Dulcimer
Drawbar Organ 1
Percussive Organ
Rock Organ
Church Organ 1
Reed Organ
Accordion
Hamonica
Tango Accordion
Acoustic Guitar (nylon) 1
Acoustic Guitar (steel)
Electric Guitar (jazz)
Electric Guitar (clean)
Electric Guitar (muted)
Overdriven Guitar
Distortion Guitar
Guitar Harmonics
Acoustic Bass
Electric Bass (finger)
Electric Bass (pick)
Fretless Bass
Slap Bass 1
Slap Bass 2
Synth Bass 1
Synth Bass 2
Violin
Viola
Cello
Contrabass
Tremolo Strings
Pizzicato Strings
Orchestral Harp
Timpani
String Ensemble 1
String Ensemble 2
Synth Strings 1
Synth Strings 2
Choir Aahs
Voice Oohs
Synth Voice
Orchestra Hit
Trumpet
Trombone
Tuba
Muted Trumpet
French Horn
Brass Section 1
Synth Brass 1
Synth Brass 2
Soprano Sax
Alto Sax
Tenor Sax
Baritone Sax
Oboe
English Horn
Bassoon
Clarinet
Piccolo
Flute
Recorder
Pan Flute
Blown Bottle
Shakuhachi
Whistle
Ocarina
Lead 1 (square)
Lead 2 (sawtooth)
Lead 3 (calliope)
Lead 4 (chiff)
Lead 5 (charang)
Lead 6 (voice)
Lead 7 (fifths)
Lead 8 (bass+lead)
Pad 1 (new age)
Pad 2 (warm)
Pad 3 (polysynth)
Pad 4 (choir)
Pad 5 (bowed)
Pad 6 (metallic)
Pad 7 (halo)
Pad 8 (sweep)
FX 1 (rain)
FX 2 (soundtrack)
FX 3 (crystal)
FX 4 (atmosphere)
FX 5 (brightness)
FX 6 (goblins)
FX 7 (echoes)
FX 8 (sci-fi)
Sitar
Banjo
Shamisen
Koto
Kalimba
Bagpipe
Fiddle
Shanai
Tinkle Bell
Agogo
Steel Drums
Woodblock
Taiko Drum
Melodic Tom 1
Synth Drum
Reverse Cymbal
Guitar Fret Noise
Breath Noise
Seashore
Bird Tweet
Telephone Ring
Helicopter
Applause
Gunshot
: Same as Bank 0
108
CP300 Owner’s Manual
Bank 0
GrandPno
BritePno
El.Grand
HnkyTonk
E.Piano1
E.Piano2
Harpsi.
Clavi.
Celesta
Glocken
MusicBox
Vibes
Marimba
Xylophon
TubulBel
Dulcimer
DrawOrgn
PercOrgn
RockOrgn
ChrchOrg
ReedOrgn
Acordion
Harmnica
TangoAcd
NylonGtr
SteelGtr
Jazz Gtr
CleanGtr
Mute.Gtr
Ovrdrive
Dist.Gtr
GtrHarmo
Aco.Bass
FngrBass
PickBass
Fretless
SlapBas1
SlapBas2
SynBass1
SynBass2
Violin
Viola
Cello
Contrabs
Trem.Str
Pizz.Str
Harp
Timpani
Strings1
Strings2
Syn.Str1
Syn.Str2
ChoirAah
VoiceOoh
SynVoice
Orch.Hit
Trumpet
Trombone
Tuba
Mute.Trp
Fr. Horn
BrasSect
SynBrss1
SynBrss2
SprnoSax
Alto Sax
TenorSax
Bari.Sax
Oboe
Eng.Horn
Bassoon
Clarinet
Piccolo
Flute
Recorder
PanFlute
Bottle
Shakhchi
Whistle
Ocarina
SquareLd
Saw Ld
CaliopLd
Chiff Ld
CharanLd
Voice Ld
Fifth Ld
Bass&Ld
NewAgePd
Warm Pad
PolySyPd
ChoirPad
BowedPad
MetalPad
Halo Pad
SweepPad
Rain
SoundTrk
Crystal
Atmosphr
Bright
Goblins
Echoes
Sci-Fi
Sitar
Banjo
Shamisen
Koto
Kalimba
Bagpipe
Fiddle
Shanai
TnklBell
Agogo
SteelDrm
Woodblok
TaikoDrm
MelodTom
Syn Drum
RevCymbl
FretNoiz
BrthNoiz
Seashore
Tweet
Telphone
Helicptr
Applause
Gunshot
E
2
2
2
2
2
2
1
2
1
1
2
1
1
1
1
1
1
1
2
2
1
2
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
2
2
1
1
1
2
1
1
1
1
2
1
2
1
1
1
1
1
2
1
1
1
1
1
1
1
2
2
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
1
1
1
1
1
2
1
1
2
2
2
1
1
2
1
1
2
2
2
2
1
1
1
1
Bank 1
Stereo
E
GrndPnoK
BritPnoK
ElGrPnoK
HnkyTnkK
El.Pno1K
El.Pno2K
Harpsi.K
Clavi K
1
1
2
2
1
1
1
1
Vibes K
MarimbaK
1
1
Bank 3
Single
E
Bank 6
Slow
E
Bank 8
Fast Decay
E
Bank 12
Double Attack
E
Bank 14
E
Bright
Bank 16
NylonGt2
SteelGt2
MelloSBa
S.Strngs
S.SlwStr
2
2
S.Choir
2
: No sound E: Element number
1
Seq Bass
Slow Vln
1
SlwTrStr
1
Slow Str
LegatoSt
1
2
E
Bank 18
Resonant
E
MelloGrP
2
MelloEP1
2
Bank 19
E
Bank 20
Attack
E
Bank 24
E
70sPcOr1
2
1 AcidBass
1
1
1
MelloGtr
1
FingrDrk
2
SynBa1Dk
ClkSynBa
1
2 SynBa2Dk
FastResB
1
Arco Str
2
2 PolyBrss
2
2 HeavySyn
2
SynthAah
2
2
Trumpet2
1 BriteTrp
Tuba 2
1
2
Trmbone2
2
Soft Brs
2
Hollow
Dyna Saw
1 Shroud
1 Digi Saw
1
Quack Br
SquarLd2
Saw Ld 2
Bank 17
2
Ch.Aahs2
FrHrSolo
Dark
E
1 LMSquare
1 ThickSaw
2
RezSynBr
2
2
Big&Low
2
ThickPad
2 Soft Pad
2 Sine Pad
2
2 Big Lead
2
Shwimmer
SynDrCmp
Echoes 2
2
2 Popcorn
Echo Pan
2
2
TinyBell
WarmAtms
2
2 HollwRls
2
2
XG Voice List
Release
Piano
Chromatic
Percussion
Organ
Guitar
Bass
Strings
Ensemble
Brass
Reed
Pipe
Synth Lead
Synth Pad
Synth Effects
Ethnic
Percussive
Sound Effects
Pgm#
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
Bank 0
Bank Select LSB=00
Acoustic Grand Piano
Bright Acoustic Piano
Electric Grand Piano
Honky-tonk Piano
Electric Piano 1
Electric Piano 2
Harpsichord
Clavi
Celesta
Glockenspiel
Music Box
Vibraphone
Marimba
Xylophone
Tubular Bells
Dulcimer
Drawbar Organ 1
Percussive Organ
Rock Organ
Church Organ 1
Reed Organ
Accordion
Hamonica
Tango Accordion
Acoustic Guitar (nylon) 1
Acoustic Guitar (steel)
Electric Guitar (jazz)
Electric Guitar (clean)
Electric Guitar (muted)
Overdriven Guitar
Distortion Guitar
Guitar Harmonics
Acoustic Bass
Electric Bass (finger)
Electric Bass (pick)
Fretless Bass
Slap Bass 1
Slap Bass 2
Synth Bass 1
Synth Bass 2
Violin
Viola
Cello
Contrabass
Tremolo Strings
Pizzicato Strings
Orchestral Harp
Timpani
String Ensemble 1
String Ensemble 2
Synth Strings 1
Synth Strings 2
Choir Aahs
Voice Oohs
Synth Voice
Orchestra Hit
Trumpet
Trombone
Tuba
Muted Trumpet
French Horn
Brass Section 1
Synth Brass 1
Synth Brass 2
Soprano Sax
Alto Sax
Tenor Sax
Baritone Sax
Oboe
English Horn
Bassoon
Clarinet
Piccolo
Flute
Recorder
Pan Flute
Blown Bottle
Shakuhachi
Whistle
Ocarina
Lead 1 (square)
Lead 2 (sawtooth)
Lead 3 (calliope)
Lead 4 (chiff)
Lead 5 (charang)
Lead 6 (voice)
Lead 7 (fifths)
Lead 8 (bass+lead)
Pad 1 (new age)
Pad 2 (warm)
Pad 3 (polysynth)
Pad 4 (choir)
Pad 5 (bowed)
Pad 6 (metallic)
Pad 7 (halo)
Pad 8 (sweep)
FX 1 (rain)
FX 2 (soundtrack)
FX 3 (crystal)
FX 4 (atmosphere)
FX 5 (brightness)
FX 6 (goblins)
FX 7 (echoes)
FX 8 (sci-fi)
Sitar
Banjo
Shamisen
Koto
Kalimba
Bagpipe
Fiddle
Shanai
Tinkle Bell
Agogo
Steel Drums
Woodblock
Taiko Drum
Melodic Tom 1
Synth Drum
Reverse Cymbal
Guitar Fret Noise
Breath Noise
Seashore
Bird Tweet
Telephone Ring
Helicopter
Applause
Gunshot
: Same as Bank 0
Bank 0
GrandPno
BritePno
El.Grand
HnkyTonk
E.Piano1
E.Piano2
Harpsi.
Clavi.
Celesta
Glocken
MusicBox
Vibes
Marimba
Xylophon
TubulBel
Dulcimer
DrawOrgn
PercOrgn
RockOrgn
ChrchOrg
ReedOrgn
Acordion
Harmnica
TangoAcd
NylonGtr
SteelGtr
Jazz Gtr
CleanGtr
Mute.Gtr
Ovrdrive
Dist.Gtr
GtrHarmo
Aco.Bass
FngrBass
PickBass
Fretless
SlapBas1
SlapBas2
SynBass1
SynBass2
Violin
Viola
Cello
Contrabs
Trem.Str
Pizz.Str
Harp
Timpani
Strings1
Strings2
Syn.Str1
Syn.Str2
ChoirAah
VoiceOoh
SynVoice
Orch.Hit
Trumpet
Trombone
Tuba
Mute.Trp
Fr. Horn
BrasSect
SynBrss1
SynBrss2
SprnoSax
Alto Sax
TenorSax
Bari.Sax
Oboe
Eng.Horn
Bassoon
Clarinet
Piccolo
Flute
Recorder
PanFlute
Bottle
Shakhchi
Whistle
Ocarina
SquareLd
Saw Ld
CaliopLd
Chiff Ld
CharanLd
Voice Ld
Fifth Ld
Bass&Ld
NewAgePd
Warm Pad
PolySyPd
ChoirPad
BowedPad
MetalPad
Halo Pad
SweepPad
Rain
SoundTrk
Crystal
Atmosphr
Bright
Goblins
Echoes
Sci-Fi
Sitar
Banjo
Shamisen
Koto
Kalimba
Bagpipe
Fiddle
Shanai
TnklBell
Agogo
SteelDrm
Woodblok
TaikoDrm
MelodTom
Syn Drum
RevCymbl
FretNoiz
BrthNoiz
Seashore
Tweet
Telphone
Helicptr
Applause
Gunshot
E
Bank 25
2
2
2
2
2
2
1 Harpsi.2
2
1
1
2
1
1
1
1
1
1
1
2
2
1
2
1
2
1 NylonGt3
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
2
2
1
1
1
2
1
1
1
1
2
1
2
1
1
1
1
1
2
1
1
1
1
1
1
1
2
2
1
1
2
2 WaspySyn
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
1
1
1
1
1
2
1
1
2
2
2
1
1
2
1
1
2
2
2
2
1
1
1
1
Rezo Sweep
E
Bank 27
Muted
E
Bank 28
Detune 1
E
Bank 32
Detune 2
E
Bank 33
Detune 3
E
Bank 34
Octave 1
E
Bank 35
Octave 2
E
Bank 36
5th 1
E
Bank 37
5th 2
E
Bank 38
Bend
E
Bank 39
Tutti
E
Bank 40
PianoStr
Det.CP80
2
LayerCP1
2
Chor.EP1
Chor.EP2
2
2 DX Hard
HardEl.P
DX Phase
2
2
16+2"2/3
2
2 DXLegend
2
2
Harpsi.3
ClaviWah
E
2
2
2
DetDrwOr
DetPrcOr
2 60sDrOr1
2 Lite Org
ChurOrg3
2
AccordIt
Harmo. 2
2
2
Jazz Amp
ChorusGt
2
2
2 60sDrOr2
2
Dulcimr2
2 70sDrOr1
2
2 DrawOrg2
2 60sDrOr3
PercOrg2
2 Even Bar
2
2
ChurOrg2
2
NotreDam
Puff Org
2
2
12StrGtr
2
Nyln&Stl
2
FunkGtr1
2
2
FlangeBa
2
ResoSlap
1
MutePkBa
Fretles2
PunchThm
2 Fretles3
2
SmthSynB
2
2 Fretles4
2
2
TechnoBa
ModulrBa
2
2
Susp.Str
2
2
60sStrng
2
2
YangChin
2
Orchestr
Warm Str
2
2
ChoirStr
2
SyVoice2
2
BrssSec2
2
2
MelChoir
SynBrss3
2
JazzRthm
Ba&DstEG
1
Clv Bass
Reso Str
FeedbkGt
2
2
Warm Trp
2
FrHorn 2
1
JumpBrss
2
OrchHit2
2
Tp&TbSec
2
HornOrch
2
Converge
2
Prologue
2
DetSitar
MuteBnjo
2
Big Five
2
RndGlock
2
Sitar 2
2
Appendix
Instrument
Group
2
SynBrss4
2
Sax Sect
BrthTnSx
2
2
PulseSaw
2
GlockChi
Nylon EP
2
2
1
: No sound E: Element number
CP300 Owner’s Manual
109
XG Voice List
Velo-Switch
Instrument
Group
Piano
Chromatic
Percussion
Organ
Guitar
Bass
Strings
Ensemble
Brass
Appendix
Reed
Pipe
Synth Lead
Synth Pad
Synth Effects
Ethnic
Percussive
Sound Effects
Pgm#
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
Bank 0
Bank Select LSB=00
Acoustic Grand Piano
Bright Acoustic Piano
Electric Grand Piano
Honky-tonk Piano
Electric Piano 1
Electric Piano 2
Harpsichord
Clavi
Celesta
Glockenspiel
Music Box
Vibraphone
Marimba
Xylophone
Tubular Bells
Dulcimer
Drawbar Organ 1
Percussive Organ
Rock Organ
Church Organ 1
Reed Organ
Accordion
Hamonica
Tango Accordion
Acoustic Guitar (nylon) 1
Acoustic Guitar (steel)
Electric Guitar (jazz)
Electric Guitar (clean)
Electric Guitar (muted)
Overdriven Guitar
Distortion Guitar
Guitar Harmonics
Acoustic Bass
Electric Bass (finger)
Electric Bass (pick)
Fretless Bass
Slap Bass 1
Slap Bass 2
Synth Bass 1
Synth Bass 2
Violin
Viola
Cello
Contrabass
Tremolo Strings
Pizzicato Strings
Orchestral Harp
Timpani
String Ensemble 1
String Ensemble 2
Synth Strings 1
Synth Strings 2
Choir Aahs
Voice Oohs
Synth Voice
Orchestra Hit
Trumpet
Trombone
Tuba
Muted Trumpet
French Horn
Brass Section 1
Synth Brass 1
Synth Brass 2
Soprano Sax
Alto Sax
Tenor Sax
Baritone Sax
Oboe
English Horn
Bassoon
Clarinet
Piccolo
Flute
Recorder
Pan Flute
Blown Bottle
Shakuhachi
Whistle
Ocarina
Lead 1 (square)
Lead 2 (sawtooth)
Lead 3 (calliope)
Lead 4 (chiff)
Lead 5 (charang)
Lead 6 (voice)
Lead 7 (fifths)
Lead 8 (bass+lead)
Pad 1 (new age)
Pad 2 (warm)
Pad 3 (polysynth)
Pad 4 (choir)
Pad 5 (bowed)
Pad 6 (metallic)
Pad 7 (halo)
Pad 8 (sweep)
FX 1 (rain)
FX 2 (soundtrack)
FX 3 (crystal)
FX 4 (atmosphere)
FX 5 (brightness)
FX 6 (goblins)
FX 7 (echoes)
FX 8 (sci-fi)
Sitar
Banjo
Shamisen
Koto
Kalimba
Bagpipe
Fiddle
Shanai
Tinkle Bell
Agogo
Steel Drums
Woodblock
Taiko Drum
Melodic Tom 1
Synth Drum
Reverse Cymbal
Guitar Fret Noise
Breath Noise
Seashore
Bird Tweet
Telephone Ring
Helicopter
Applause
Gunshot
: Same as Bank 0
110
CP300 Owner’s Manual
Bank 0
GrandPno
BritePno
El.Grand
HnkyTonk
E.Piano1
E.Piano2
Harpsi.
Clavi.
Celesta
Glocken
MusicBox
Vibes
Marimba
Xylophon
TubulBel
Dulcimer
DrawOrgn
PercOrgn
RockOrgn
ChrchOrg
ReedOrgn
Acordion
Harmnica
TangoAcd
NylonGtr
SteelGtr
Jazz Gtr
CleanGtr
Mute.Gtr
Ovrdrive
Dist.Gtr
GtrHarmo
Aco.Bass
FngrBass
PickBass
Fretless
SlapBas1
SlapBas2
SynBass1
SynBass2
Violin
Viola
Cello
Contrabs
Trem.Str
Pizz.Str
Harp
Timpani
Strings1
Strings2
Syn.Str1
Syn.Str2
ChoirAah
VoiceOoh
SynVoice
Orch.Hit
Trumpet
Trombone
Tuba
Mute.Trp
Fr. Horn
BrasSect
SynBrss1
SynBrss2
SprnoSax
Alto Sax
TenorSax
Bari.Sax
Oboe
Eng.Horn
Bassoon
Clarinet
Piccolo
Flute
Recorder
PanFlute
Bottle
Shakhchi
Whistle
Ocarina
SquareLd
Saw Ld
CaliopLd
Chiff Ld
CharanLd
Voice Ld
Fifth Ld
Bass&Ld
NewAgePd
Warm Pad
PolySyPd
ChoirPad
BowedPad
MetalPad
Halo Pad
SweepPad
Rain
SoundTrk
Crystal
Atmosphr
Bright
Goblins
Echoes
Sci-Fi
Sitar
Banjo
Shamisen
Koto
Kalimba
Bagpipe
Fiddle
Shanai
TnklBell
Agogo
SteelDrm
Woodblok
TaikoDrm
MelodTom
Syn Drum
RevCymbl
FretNoiz
BrthNoiz
Seashore
Tweet
Telphone
Helicptr
Applause
Gunshot
E
2
2
2
2
2
2
1
2
1
1
2
1
1
1
1
1
1
1
2
2
1
2
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
2
2
1
1
1
2
1
1
1
1
2
1
2
1
1
1
1
1
2
1
1
1
1
1
1
1
2
2
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
1
1
1
1
1
2
1
1
2
2
2
1
1
2
1
1
2
2
2
2
1
1
1
1
Bank 41
E
Bank 42
Dream
2
LayerCP2
2
DX+Analg
2 DXKotoEP
E
Bank 43
Velo-Xfade
E
Bank 45
VX El.P1
VX El.P2
2
HardVibe
Stl&Body
Bank 64
2 60sEl.P1
2
E
Bank 65
E
Bank 66
E
Bank 67
E
Bank 68
E
Bank 69
E
Bank 70
E
Bank 71
E
1
PulseClv
1 PierceCl
Orgel
2
SineMrmb
2
2
2
VelGtHrm
2
FunkGtr2
Gt.Pinch
2 Jazz Man
2
1
FngrSlap
VXUprght
2 FngBass2
2
2
VeloSlap
2
Organ Ba
1 70sDrOr2
2 CheezOrg
2 DrawOrg3
RotaryOr
OrgFlute
2 SloRotar
2 TrmOrgFl
2 FstRotar
2
2
TngoAcd2
2
GtFeedbk
1 GtrHrmo2
1
Mod.Bass
2
2
2
MuteStlG
2
FeedbkG2
2
DX Bass
2
Orchstr2
Kingdom
2 TremOrch
2
Choral
2
Hi Brass
2 MelloBrs
ChoirBrs
2
SoftTenr
2
Dr. Lead
2
2
Velo.Str
AnVelBr1
AnVelBr2
: No sound E: Element number
2 Sqr.Bass
2
1 RubberBa
70s Str
Syn Str4
1 Strings3
2 Syn Str5
1
2
AnaVoice
Impact
1
2
2 AnaBrss1
2 AnaBrss2
2
2
TnrSax 2
1
Mellow
2 SoloSine
2
2
2
VeloLead
ClaviPad
2 ChorBell
Orbiter
X WireBa
2
HyprAlto
ClearBel
other wave
E
2
2 SineLead
1
2
PureLead
2
Rubby
DistLead
Vox Lead
2
2 WireLead
2
2
Fat&Prky
Fantasy
Horn Pad
PolyPd80
Heaven
Glacier
Tine Pad
2
2
2
2
2
2
2
PolarPad
2 HrmoRain
Ancestrl
SynMalet
NylnHarp
FantaBel
GobSynth
EchoBell
Starz
2
2
2
1
2
2
2
2
2
Soft Wrl
2
RotarStr
ClickPad
GlassPad
Pan Pad
2
2 Ana. Pad
Itopia
2
2
AfrcnWnd
Celstial
2 Carib
2
2
SftCryst
Harp Vox
2 LoudGlok
2 AtmosPad
2 ChrstBel
2 Planet
2 VibeBell
2
2 DigiBell
2 AirBells
Creeper
Big Pan
2 Ring Pad
2 SynPiano
2 Ritual
2 Creation
2 ToHeaven
2 StarDust
2
2 Reso&Pan
2
2 Rock Tom
2
2
Shanai 2
1
Mel Tom2
Ana Tom
1 Real Tom
1 ElecPerc
2 SquarPad
2 CC Pad
2
2
Night
2 BellHarp
2
2 Glisten
2
XG Voice List
Bank Select MSB=64
Piano
Chromatic
Percussion
Organ
Guitar
Bass
Strings
Ensemble
Brass
Reed
Pipe
Synth Lead
Synth Pad
Synth Effects
Ethnic
Percussive
Sound Effects
Pgm#
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
Bank 0
Bank Select LSB=00
Acoustic Grand Piano
Bright Acoustic Piano
Electric Grand Piano
Honky-tonk Piano
Electric Piano 1
Electric Piano 2
Harpsichord
Clavi
Celesta
Glockenspiel
Music Box
Vibraphone
Marimba
Xylophone
Tubular Bells
Dulcimer
Drawbar Organ 1
Percussive Organ
Rock Organ
Church Organ 1
Reed Organ
Accordion
Hamonica
Tango Accordion
Acoustic Guitar (nylon) 1
Acoustic Guitar (steel)
Electric Guitar (jazz)
Electric Guitar (clean)
Electric Guitar (muted)
Overdriven Guitar
Distortion Guitar
Guitar Harmonics
Acoustic Bass
Electric Bass (finger)
Electric Bass (pick)
Fretless Bass
Slap Bass 1
Slap Bass 2
Synth Bass 1
Synth Bass 2
Violin
Viola
Cello
Contrabass
Tremolo Strings
Pizzicato Strings
Orchestral Harp
Timpani
String Ensemble 1
String Ensemble 2
Synth Strings 1
Synth Strings 2
Choir Aahs
Voice Oohs
Synth Voice
Orchestra Hit
Trumpet
Trombone
Tuba
Muted Trumpet
French Horn
Brass Section 1
Synth Brass 1
Synth Brass 2
Soprano Sax
Alto Sax
Tenor Sax
Baritone Sax
Oboe
English Horn
Bassoon
Clarinet
Piccolo
Flute
Recorder
Pan Flute
Blown Bottle
Shakuhachi
Whistle
Ocarina
Lead 1 (square)
Lead 2 (sawtooth)
Lead 3 (calliope)
Lead 4 (chiff)
Lead 5 (charang)
Lead 6 (voice)
Lead 7 (fifths)
Lead 8 (bass+lead)
Pad 1 (new age)
Pad 2 (warm)
Pad 3 (polysynth)
Pad 4 (choir)
Pad 5 (bowed)
Pad 6 (metallic)
Pad 7 (halo)
Pad 8 (sweep)
FX 1 (rain)
FX 2 (soundtrack)
FX 3 (crystal)
FX 4 (atmosphere)
FX 5 (brightness)
FX 6 (goblins)
FX 7 (echoes)
FX 8 (sci-fi)
Sitar
Banjo
Shamisen
Koto
Kalimba
Bagpipe
Fiddle
Shanai
Tinkle Bell
Agogo
Steel Drums
Woodblock
Taiko Drum
Melodic Tom 1
Synth Drum
Reverse Cymbal
Guitar Fret Noise
Breath Noise
Seashore
Bird Tweet
Telephone Ring
Helicopter
Applause
Gunshot
Bank 0
GrandPno
BritePno
El.Grand
HnkyTonk
E.Piano1
E.Piano2
Harpsi.
Clavi.
Celesta
Glocken
MusicBox
Vibes
Marimba
Xylophon
TubulBel
Dulcimer
DrawOrgn
PercOrgn
RockOrgn
ChrchOrg
ReedOrgn
Acordion
Harmnica
TangoAcd
NylonGtr
SteelGtr
Jazz Gtr
CleanGtr
Mute.Gtr
Ovrdrive
Dist.Gtr
GtrHarmo
Aco.Bass
FngrBass
PickBass
Fretless
SlapBas1
SlapBas2
SynBass1
SynBass2
Violin
Viola
Cello
Contrabs
Trem.Str
Pizz.Str
Harp
Timpani
Strings1
Strings2
Syn.Str1
Syn.Str2
ChoirAah
VoiceOoh
SynVoice
Orch.Hit
Trumpet
Trombone
Tuba
Mute.Trp
Fr. Horn
BrasSect
SynBrss1
SynBrss2
SprnoSax
Alto Sax
TenorSax
Bari.Sax
Oboe
Eng.Horn
Bassoon
Clarinet
Piccolo
Flute
Recorder
PanFlute
Bottle
Shakhchi
Whistle
Ocarina
SquareLd
Saw Ld
CaliopLd
Chiff Ld
CharanLd
Voice Ld
Fifth Ld
Bass&Ld
NewAgePd
Warm Pad
PolySyPd
ChoirPad
BowedPad
MetalPad
Halo Pad
SweepPad
Rain
SoundTrk
Crystal
Atmosphr
Bright
Goblins
Echoes
Sci-Fi
Sitar
Banjo
Shamisen
Koto
Kalimba
Bagpipe
Fiddle
Shanai
TnklBell
Agogo
SteelDrm
Woodblok
TaikoDrm
MelodTom
Syn Drum
RevCymbl
FretNoiz
BrthNoiz
Seashore
Tweet
Telphone
Helicptr
Applause
Gunshot
E
Bank 72
2
2
2
2
2
2
1
2
1
1
2
1
1
1
1
1
1
1
2
2
1
2
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
2
2
1
1
1
2
1
1
1
1
2
1
2
1
1
1
1
1
2
1
1
1
1
1
1
1
2
2
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2 Gamelmba
2
2
2
2
2
1
1
1
1
1
2
1
1
2
2
2
1
1
2
1
1
2
2
2
2
1
1
1
1
E
Bank 96
E
Bank 97
Balimba
ChrchBel
Cimbalom
2 Carillon
2 Santur
Ukulele
Mandolin
1
2
SynFretl
2 SmthFrtl
Hammer
2
Seq Ana.
E
Bank 98
2 Log Drum
E
Bank 99
E
Bank 100
E
Bank 101
E
2
2
2
2
2
2
Smokey
BelChoir
2
2
Tambra
Rabab
2 Tamboura
2 Gopichnt
2
2 Oud
Taisho-k
2 Kanoon
2
Pungi
Bonang
1 Hichriki
2 Altair
2
2 Gamelan
2 S.Gamlan
2 ThaiBell
2
Castanet
Gr.Cassa
1
1
GlasPerc
2
2 Rama Cym
2 AsianBel
2
Pgm#
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
SFX
Bank 0
E
CuttngNz
CttngNz2
1
2
Str Slap
1
Fl.KClik
1
Shower
Thunder
Wind
Stream
Bubble
Feed
1
1
1
2
2
2
Dog
Horse
Tweet 2
1
1
1
Ghost
Maou
2
2
PhonCall
DoorSqek
Door Slam
ScratchC
ScratchS
WindChim
Telphon2
1
1
1
1
2
1
1
CarEIgnt
CarTSqel
Car Pass
CarCrash
Siren
Train
JetPlane
Starship
Burst
Coaster
Submarin
1
1
1
1
2
1
2
2
2
2
2
Laugh
Scream
Punch
Heart
Footstep
1
1
1
1
1
MchinGun
LaserGun
Xplosion
Firework
1
2
2
2
CP300 Owner’s Manual
Appendix
Instrument
Group
111
XG Drum Kit List
• Key-off: Keys marked “O” stop sounding the instant they are released.
• Alternate Group: Playing any instrument within a numbered group will immediately stop the sound of any other
instrument in the same group of the same number
No Sound
Bank Select MSB (0-127)
127
127
127
127
127
127
Bank Select LSB (0-127)
0
0
0
0
0
0
0
Program Change (1-128)
1
2
9
17
25
26
28
Standard Kit1
Standard Kit2
Room Kit
Rock Kit
Electro Kit
Analog Kit
Dance Kit
MIDI
Note# Note
Appendix
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
112
Same as Standard Kit 1
C#-1
D-1
D#-1
E-1
F-1
F#-1
G-1
G#-1
A-1
A#-1
B-1
C0
C#0
D0
D#0
E0
F0
F#0
G0
G#0
A0
A#0
B0
C1
C#1
D1
D#1
E1
F1
F#1
G1
G#1
A1
A#1
B1
C2
C#2
D2
D#2
E2
F2
F#2
G2
G#2
A2
A#2
B2
C3
C#3
D3
D#3
E3
F3
F#3
G3
G#3
A3
A#3
B3
C4
C#4
D4
D#4
E4
F4
F#4
G4
G#4
A4
A#4
B4
C5
C#5
D5
D#5
E5
F5
F#5
G5
Key Alternate
Off
Group
3
3
4
4
O
O
O
1
1
1
O
O
O
2
2
Surdo Mute
Surdo Open
Hi Q
Whip Slap
Scratch H
Scratch L
Finger Snap
Click Noise
Metronome Click
Metronome Bell
Seq Click L
Seq Click H
Brush Tap
Brush Swirl
Brush Slap
Brush Tap Swirl
Snare Roll
Castanet
Snare Soft
Sticks
Kick Soft
Open Rim Shot
Kick Tight
Kick
Side Stick
Snare
Hand Clap
Snare Tight
Floor Tom L
Hi-Hat Closed
Floor Tom H
Hi-Hat Pedal
Low Tom
Hi-Hat Open
Mid Tom L
Mid Tom H
Crash Cymbal 1
High Tom
Ride Cymbal 1
Chinese Cymbal
Ride Cymbal Cup
Tambourine
Splash Cymbal
Cowbell
Crash Cymbal 2
Vibraslap
Ride Cymbal 2
Bongo H
Bongo L
Conga H Mute
Conga H Open
Conga L
Timbale H
Timbale L
Agogo H
Agogo L
Cabasa
Maracas
Samba Whistle H
Samba Whistle L
Guiro Short
Guiro Long
Claves
Wood Block H
Wood Block L
Cuica Mute
Cuica Open
Triangle Mute
Triangle Open
Shaker
Jingle Bells
Bell Tree
CP300 Owner’s Manual
Reverse Cymbal
Reverse Cymbal
Reverse Cymbal
Hi Q 2
Snare Snappy Electro
Hi Q 2
Snare Noisy 4
Hi Q 2
Snare Techno
Kick 3
Kick 3
Kick 2
Kick Gate
Kick Gate
Kick Gate Heavy
Snare Snappy
Snare Rock
Snare Noisy 2
Kick Analog Short
Kick Analog
Side Stick Analog
Snare Analog
Kick Techno Q
Rim Gate
Kick Techno L
Kick Techno
Side Stick Analog
Snare Clap
Snare Tight Snappy
Tom Room 1
Snare Rock Tight
Tom Rock 1
Snare Noisy 3
Tom Electro 1
Tom Room 2
Tom Rock 2
Tom Electro 2
Tom Room 3
Tom Rock 3
Tom Electro 3
Tom Room 4
Tom Room 5
Tom Rock 4
Tom Rock 5
Tom Electro 4
Tom Electro 5
Tom Room 6
Tom Rock 6
Tom Electro 6
Snare Analog 2
Tom Analog 1
Hi-Hat Closed Analog
Tom Analog 2
Hi-Hat Closed Analog 2
Tom Analog 3
Hi-Hat Open Analog
Tom Analog 4
Tom Analog 5
Crash Analog
Tom Analog 6
Snare Dry
Tom Analog 1
Hi-Hat Closed 3
Tom Analog 2
Hi-Hat Closed Analog 3
Tom Analog 3
Hi-Hat Open 3
Tom Analog 4
Tom Analog 5
Crash Analog
Tom Analog 6
Cowbell Analog
Cowbell Analog
Conga Analog H
Conga Analog M
Conga Analog L
Conga Analog H
Conga Analog M
Conga Analog L
Maracas 2
Maracas 2
Claves 2
Claves 2
Scratch H 2
Scratch L 2
Scratch H 2
Scratch L 2
Snare Soft 2
Snare Noisy
Open Rim Shot H Short
Kick Short
Side Stick Light
Snare Short
Snare Tight H
127
Scratch H 2
Scratch L 2
XG Drum Kit List
Bank Select MSB (0-127)
127
127
127
126
Bank Select LSB (0-127)
0
0
0
0
0
Program Change (1-128)
33
41
49
1
2
Jazz Kit
Brush Kit
Symphony Kit
SFX Kit1
SFX Kit2
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
C#-1
D-1
D#-1
E-1
F-1
F#-1
G-1
G#-1
A-1
A#-1
B-1
C0
C#0
D0
D#0
E0
F0
F#0
G0
G#0
A0
A#0
B0
C1
C#1
D1
D#1
E1
F1
F#1
G1
G#1
A1
A#1
B1
C2
C#2
D2
D#2
E2
F2
F#2
G2
G#2
A2
A#2
B2
C3
C#3
D3
D#3
E3
F3
F#3
G3
G#3
A3
A#3
B3
C4
C#4
D4
D#4
E4
F4
F#4
G4
G#4
A4
A#4
B4
C5
C#5
D5
D#5
E5
F5
F#5
G5
Key Alternate
Off
Group
3
3
4
4
O
O
O
Snare Jazz H
Brush Slap 2
Kick Soft 2
Open Rim Shot Light
Kick Jazz
Side Stick Light
Snare Jazz L
Kick Jazz
Side Stick Light
Brush Slap 3
Snare Jazz M
Brush Tap 2
Tom Brush 1
Gran Cassa
Gran Cassa Mute
Cutting Noise
Cutting Noise 2
Band Snare
String Slap
Band Snare 2
1
Phone Call
Door Squeak
Door Slam
Scratch Cut
Scratch H 3
Wind Chime
Telephone Ring 2
Tom Brush 2
1
Tom Brush 3
Appendix
MIDI
Note# Note
126
1
Tom Brush 4
Tom Brush 5
Hand Cymbal
Tom Brush 6
Hand Cymbal Short
Flute Key Click
Car Engine Ignition
Car Tires Squeal
Car Passing
Car Crash
Siren
Train
Jet Plane
Starship
Burst
Roller Coaster
Submarine
Shower
Thunder
Wind
Stream
Bubble
Feed
Laugh
Scream
Punch
Heart Beat
Foot Steps
Dog
Horse
Bird Tweet 2
Machine Gun
Laser Gun
Explosion
Firework
Hand Cymbal 2
Hand Cymbal 2 Short
O
O
O
2
2
Ghost
Maou
CP300 Owner’s Manual
113
Effect Type List
■ Reverb
■ Variation/Insertion
Reverb types that can be selected by
panel operation
Type MSB
Type LSB
2
1
1
3
4
17
19
17
17
16
Effect Name
Room 4
Hall 4
Hall 3
Stage 3
Plate 2
Display
Room
Hall 1
Hall 2
Stage
Plate
All reverb types
Appendix
Type MSB
Type LSB
0
1
1
1
1
1
1
2
2
2
2
2
2
2
3
3
3
3
4
4
4
16
17
18
19
0
0
1
6
7
17
19
0
1
2
5
6
7
17
0
1
17
18
0
7
16
0
0
0
0
Effect Name
No Effect
Hall 1
Hall 2
Hall M
Hall L
Hall 3
Hall 4
Room 1
Room 2
Room 3
Room S
Room M
Room L
Room 4
Stage 1
Stage 2
Stage 3
Sound Board
Plate 1
GM Plate
Plate 2
White Room
Tunnel
Canyon
Basement
Chorus types that can be selected by
panel operation
Type LSB
65
66
67
8
8
1
Effect Name
Chorus 4
Celeste 4
Flanger 2
Display
Chorus
Celeste
Flanger
All chorus types
114
Type MSB
Type LSB
0
65
65
65
65
65
65
65
65
65
66
66
66
66
66
67
67
67
67
68
68
72
72
72
87
0
0
1
2
3
4
5
6
7
8
0
1
2
8
18
0
1
7
8
0
16
0
8
20
0
Effect Name
No Effect
Chorus 1
Chorus 2
Chorus 3
GM Chorus 1
GM Chorus 2
GM Chorus 3
GM Chorus 4
FB Chorus
Chorus 4
Celeste 1
Celeste 2
Celeste 3
Celeste 4
Rotary Speaker 1
Flanger 1
Flanger 2
GM Flanger
Flanger 3
Symphonic 1
Symphonic 2
Phaser 1
Phaser 2
Phaser 3
Ens Detune
CP300 Owner’s Manual
Type MSB Type LSB
5
6
7
8
68
66
70
119
71
72
78
3
75
83
16
0
0
0
16
18
22
0
27
20
21
18
26
16
Effect Name
Display
DelayL,C,R 2
Delay L,R
Echo
Cross Delay
Symphonic 2
RotarySpeaker1
Tremolo 3
VibeRotor
Auto Pan 3
Phaser 3
Auto Wah 2
Sound Board
AmpSimulator2
Compressor 2
Delay L,C,R
Delay L,R
Echo
Cross Delay
Symphonic
Rotary Speaker
Tremolo
VibeRotor
Auto Pan
Phaser
Auto Wah
Sound Board
Amp Simulator
Compressor
All variation/insertion effects
■ Chorus
Type MSB
Variation/insertion types that can be
selected by panel operation
Type MSB
Type LSB
0
1
1
1
1
2
2
2
2
2
2
3
3
3
4
4
5
5
6
7
8
9
9
10
11
16
17
18
19
20
20
20
21
21
22
64
65
65
65
65
65
65
65
65
65
66
66
66
66
66
67
67
67
67
0
0
1
6
7
0
1
2
5
6
7
0
1
18
0
7
0
16
0
0
0
0
1
0
0
0
0
0
0
0
1
2
0
8
0
0
0
1
2
3
4
5
6
7
8
0
1
2
8
18
0
1
7
8
Effect Name
No Effect
Hall 1
Hall 2
Hall M
Hall L
Room 1
Room 2
Room 3
Room S
Room M
Room L
Stage 1
Stage 2
Sound Board
Plate
GM Plate
Delay L,C,R 1
Delay L,C,R 2
Delay L,R
Echo
Cross Delay
ER1
ER2
Gate Reverb
Reverse Gate
White Room
Tunnel
Canyon
Basement
Karaoke 1
Karaoke 2
Karaoke 3
Tempo Delay
Tempo Echo
Tempo Cross
Thru
Chorus1
Chorus2
Chorus3
GM Chorus 1
GM Chorus 2
GM Chorus 3
GM Chorus 4
FB Chorus
Chorus 4
Celeste 1
Celeste 2
Celeste 3
Celeste 4
Rotary Speaker 1
Flanger 1
Flanger 2
GM Flanger
Flanger 3
Type MSB
Type LSB
68
68
69
69
69
69
70
70
70
71
71
71
72
72
72
73
73
73
74
74
75
75
75
76
77
78
78
78
78
80
80
81
82
82
82
82
83
83
84
85
86
86
86
86
87
88
93
94
95
95
96
96
97
97
98
98
98
98
99
99
100
100
101
101
102
102
103
103
119
0
16
0
1
2
3
0
19
22
0
26
27
0
8
20
0
1
8
0
8
0
8
26
0
0
0
1
2
21
0
1
0
0
1
2
8
0
16
0
0
0
1
2
3
0
0
0
0
0
1
0
1
0
1
0
1
2
3
0
1
0
1
0
1
0
1
0
1
0
Effect Name
Symphonic 1
Symphonic 2
Rotary Speaker 2
Dist + Rot Sp
OD + Rot Sp
Amp Sin + Rot Sp
Tremolo 1
Tremolo 2
Tremolo 3
AutoPan 1
AutoPan 2
AutoPan 3
Phaser 1
Phaser 2
Phaser 3
Distortion
Comp Dist
Stereo Dist
Over Drive
Stereo OD
Amp Simulator 1
Stereo Amp Sim
Amp Simulator 2
3 Band EQ
2 Band EQ
Auto Wah 1
Auto Wah + Dist
Auto Wah + OD
Auto Wah 2
Pitch Change 1
Pitch Change 2
Hrm ENH
Touch Wah 1
Touch Wah + Dist
Touch Wah + OD
Touch Wah 2
Compressor 1
Compressor 2
Noise Gate
Voice Cancel
2 Way Rot Sp
Dist + 2 Rot Sp
OD + 2 Rot Sp
Amp Sim + 2 Rot Sp
Ens Detune
Ambience
Talk Mod
Lo-Fi
Dist + Delay
OD + Delay
Cmp + Dist + Dly
Cmp + OD + Dly
Wah + Dist + Dly
Wah + OD + Dly
V Dist Hard
V Dist H + Dly
V Dist Soft
V Dist S + Dly
Dual Rot Sp 1
Dual Rot Sp 2
Dist + Tmp Delay
OD + Tmp Delay
Cmp + Dist + TDly
Cmp + OD + TDly
Wah + Dist + TDly
Wah + OD + TDly
V Dist H + TDly
V Dist S + TDly
Vibe Rotor
Effect Parameter List
Items with a dot indicator (●) in the Control column are parameters that can be controlled via assignable controllers.
Note that this is applicable to the Variation effects (while Insertion is selected) and to the Insertion effects.
HALL 1, HALL 2, HALL M, HALL L
ROOM 1, ROOM 2, ROOM 3, ROOM S, ROOM M, ROOM L
STAGE 1, STAGE 2
PLATE (Reverb, Variation, Insertion block)
4 HPF Cutoff
5 LPF Cutoff
6
7
8
9
10 Dry/Wet
11 Rev Delay
12
13
14
15
16
Density
Er/Rev Balance
High Damp
Feedback Level
Display
0.3 – 30.0s
0 – 10
0.1mS – 200.0mS (Rev)
0.1mS – 99.3mS (Var/Ins)
Thru – 8.0kHz
1.0k – Thru
Value
0 – 69
0 – 10
0 – 127
0 – 63
0 – 52
34 – 60
See Table Control
table #4
table #5
table #3
table #3
●
D63>W – D=W – D<W63
1 – 127
(table #15)
0.1mS – 200.0mS (Rev)
0.1mS – 99.3mS (Var/Ins)
0–4
E63>R – E=R – E<R63
0.1 – 1.0
-63 – +63
0 – 127
0 – 63
0–4
1 – 127
1 – 10
1 – 127
table #5
Parameter
Reverb Time
Diffusion
Initial Delay
HPF Cutoff
LPF Cutoff
Display
0.3 – 30.0s
0 – 10
0.1mS – 99.3mS
Thru – 8.0kHz
1.0k – Thru
Value
0 – 69
0 – 10
0 – 63
0 – 52
34 – 60
See Table Control
table #4
Dry/Wet
11
12
13
14 High Damp
15
16
D63>W – D=W – D<W63
1 – 127
table #5
table #3
table #3
(table #15)
11
12
13
14
15
16
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Display
0.1 – 1638.3ms
0.1 – 1638.3ms
0.1 – 1638.3ms
0.1 – 1638.3ms
-63 – +63
0.1 – 1.0
Value
See Table Control
1 – 16383
1 – 16383
1 – 16383
1 – 16383
1 – 127
1 – 10
Dry/Wet
D63>W – D=W – D<W63
1 – 127
EQ Low Frequency
EQ Low Gain
EQ High Frequency
EQ High Gain
32Hz – 2.0kHz
-12 – +12dB
500Hz – 16.0kHz
-12 – +12dB
4 – 40
52 – 76
28 – 58
52 – 76
●
table #3
table #3
Parameter
Lch Delay1
Lch Feedback Level
Rch Delay1
Rch Feedback Level
High Damp
Lch Delay2
Rch Delay2
Delay2 Level
Display
0.1 – 1486.0ms
-63 – +63
0.1 – 1486.0ms
-63 – +63
0.1 – 1.0
0.1 – 1486.0ms
0.1 – 1486.0ms
0 – 127
Value
See Table Control
1 – 14860
1 – 127
1 – 14860
1 – 127
1 – 10
1 – 14860
1 – 14860
0 – 127
Dry/Wet
D63>W – D=W – D<W63
1 – 127
EQ Low Frequency
EQ Low Gain
EQ High Frequency
EQ High Gain
32Hz – 2.0kHz
-12 – +12dB
500Hz – 16.0kHz
-12 – +12dB
4 – 40
52 – 76
28 – 58
52 – 76
●
table #3
table #3
●
CROSS DELAY (Variation, Insertion block)
0.1 – 1.0
No.
1
2
3
4
5
6
7
8
9
10
1 – 10
DELAY L, C, R 1
DELAY L, C, R 2 (Variation, Insertion block)
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Parameter
Lch Delay
Rch Delay
Feedback Delay 1
Feedback Delay 2
Feedback Level
High Damp
ECHO (Variation, Insertion block)
(table #16)
HALL 3
HALL 4
ROOM 4
STAGE 3
PLATE 2 (Reverb)
No.
1
2
3
4
5
6
7
8
9
10
No.
1
2
3
4
5
6
7
8
9
10
Appendix
No.
Parameter
1 Reverb Time
2 Diffusion
3 Initial Delay
DELAY L, R (Variation, Insertion block)
Parameter
Lch Delay
Rch Delay
Cch Delay
Feedback Delay
Feedback Level
Cch Level
High Damp
Display
0.1 – 1638.3ms
0.1 – 1638.3ms
0.1 – 1638.3ms
0.1 – 1638.3ms
-63 – +63
0 – 127
0.1 – 1.0
Value
See Table Control
1 – 16383
1 – 16383
1 – 16383
1 – 16383
1 – 127
0 – 127
1 – 10
Dry/Wet
D63>W – D=W – D<W63
1 – 127
EQ Low Frequency
EQ Low Gain
EQ High Frequency
EQ High Gain
32Hz – 2.0kHz
-12 – +12dB
500Hz – 16.0kHz
-12 – +12dB
4 – 40
52 – 76
28 – 58
52 – 76
11
12
13
14
15
16
Parameter
L –>R Delay
R –>L Delay
Feedback Level
Input Select
High Damp
Display
0.1 – 1486.0ms
0.1 – 1486.0ms
-63 – +63
L, R, L&R
0.1 – 1.0
Value
See Table Control
1 – 14860
1 – 14860
1 – 127
0–2
1 – 10
Dry/Wet
D63>W – D=W – D<W63
1 – 127
EQ Low Frequency
EQ Low Gain
EQ High Frequency
EQ High Gain
32Hz – 2.0kHz
-12 – +12dB
500Hz – 16.0kHz
-12 – +12dB
4 – 40
52 – 76
28 – 58
52 – 76
●
table #3
table #3
EARLY REF 1, EARLY REF 2 (Variation, Insertion block)
●
table #3
table #3
No.
1
2
3
4
5
6
7
8
9
10
Parameter
Type
Room Size
Diffusion
Initial Delay
Feedback Level
HPF Cutoff
LPF Cutoff
Display
S-H, L-H, Rdm, Rvs, Plt, Spr
0.1 – 7.0
0 – 10
0.1ms – 200.0ms
-63 – +63
Thru – 8.0kHz
1.0k – Thru
Value
0–5
0 – 44
0 – 10
0 – 127
1 – 127
0 – 52
34 – 60
Dry/Wet
D63>W – D=W – D<W63
1 – 127
0 – 10
0–3
0.1 – 1.0
0 – 10
0–3
1 – 10
11 Liveness
12 Density
13 High Damp
14
15
16
See Table Control
table #6
table #5
table #3
table #3
●
CP300 Owner’s Manual
115
Effect Parameter List
GATE REVERB
REVERSE GATE (Variation, Insertion block)
No.
1
2
3
4
5
6
7
8
9
10
Parameter
Type
Room Size
Diffusion
Initial Delay
Feedback Level
HPF Cutoff
LPF Cutoff
Dry/Wet
11 Liveness
12 Density
13 High Damp
14
15
16
Display
Type A, Type B
0.1 – 7.0
0 – 10
0.1ms – 200.0ms
-63 – +63
Thru – 8.0kHz
1.0k – Thru
TEMPO CROSS (Variation, Insertion block)
Value
0–1
0 – 44
0 – 10
0 – 127
1 – 127
0 – 52
34 – 60
D63>W – D=W – D<W63
1 – 127
0 – 10
0–3
0.1 – 1.0
0 – 10
0–3
1 – 10
See Table Control
table #6
table #5
Parameter
Reverb Time
Diffusion
Initial Delay
HPF Cutoff
LPF Cutoff
Width
Height
Depth
Wall Vary
Dry/Wet
Display
0.3 – 30.0s
0 – 10
0.1ms – 99.3ms
Thru – 8.0kHz
1.0k – Thru
0.5 – 10.2m
0.5 – 20.2m
0.5 – 30.2m
0 – 30
D63>W – D=W – D<W63
Value
0 – 69
0 – 10
0 – 63
0 – 52
34 – 60
0 – 37
0 – 73
0 – 104
0 – 30
1 – 127
11
12
13
14
15
16
Rev Delay
Density
Er/Rev Balance
High Damp
Feedback Level
0.1ms – 99.3ms
0–4
E63>R – E=R – E<R63
0.1 – 1.0
-63 – +63
0 – 63
0–4
1 – 127
1 – 10
1 – 127
●
See Table Control
table #4
table #5
table #3
table #3
table #11
table #11
table #11
●
table #5
Appendix
KARAOKE 1, 2, 3 (Variation, Insertion block)
No.
1
2
3
4
5
6
7
8
9
10
Parameter
Delay Time
Feedback Level
HPF Cutoff
LPF Cutoff
Dry/Wet
11 Density
12
13
14
15
16
Display
0.1ms – 400.0ms
-63 – +63
Thru – 8.0kHz
1.0k – Thru
Value
0 – 127
1 – 127
0 – 52
34 – 60
D63>W – D=W – D<W63
1 – 127
0–3
0–3
See Table Control
table #7
table #3
table #3
5
116
Lag
Display
64th/3 – 4thx6
-63 – +63
0 – 1.0
Value
0 – 19
1 – 127
0 – 10
1 (-63ms) – 64 (0ms) –
127 (63ms)
1 (-63ms) – 64 (0ms) –
127 (63ms)
1 – 127
●
D63>W – D=W – D<W63
1 – 127
11
12
13
14
15
16
32Hz – 2.0kHz
-12 – +12dB
500Hz – 16.0kHz
-12 – +12dB
4 – 40
52 – 76
28 – 58
52 – 76
EQ Low Frequency
EQ Low Gain
EQ High Frequency
EQ High Gain
CP300 Owner’s Manual
See Table Control
table #14
1 – 127
6
7
8
9
10 Dry/Wet
Parameter
Delay Time L>R
Delay Time R>L
Feedback Level
Input Select
Feedback High
Dump
Lag
Value
0 – 19
0 – 19
1 – 127
0–2
0 – 10
1 (-63ms) – 64 (0ms) –
127 (63ms)
1 – 127
7
8
9
10 Dry/Wet
D63>W – D=W – D<W63
1 – 127
11
12
13
14
15
16
32Hz – 2.0kHz
-12 – +12dB
500 – 16.0kHz
-12 – +12dB
4 – 40
52 – 76
28 – 58
52 – 76
EQ Low Frequency
EQ Low Gain
EQ High Frequency
EQ High Gain
See Table Control
table #14
table #14
●
CHORUS 1, 2, 3, 4
CELESTE 1, 2, 3, 4
GM CHORUS 1, 2, 3, 4
FB CHORUS
ROTARY SPEAKER 1 (Chorus, Variation, Insertion block)
No.
1
2
3
4
5
6
7
8
9
10
Parameter
LFO Frequency
LFO Depth
Feedback Level
Delay Offset
Display
0.00Hz – 39.7Hz
0 – 127
-63 – +63
0.0mS – 50mS
Value
0 – 127
0 – 127
1 – 127
0 – 127
EQ Low Frequency
EQ Low Gain
EQ High Frequency
EQ High Gain
Dry/Wet
32Hz – 2.0kHz
-12 – +12dB
500Hz – 16.0kHz
-12 – +12dB
D63>W – D=W – D<W63
4 – 40
52 – 76
28 – 58
52 – 76
1 – 127
table #3
100Hz – 10.0kHz
14 – 54
table #3
-12 – +12dB
52 – 76
1.0 – 12.0
10 – 120
mono/stereo
0–1
11 EQ Mid Frequency
(variation block)
12 EQ Mid Gain
(variation block)
13 EQ Mid Width
(variation block)
14
15 Input Mode
16
See Table Control
table #1
table #2
table #3
●
FLANGER 1, 2, 3
GM FLANGER (Chorus, Variation, Insertion block)
TEMPO DELAY
TEMPO ECHO (Variation, Insertion block)
No.
Parameter
1 Delay Time
2 Feedback Level
3 Feedback High
Dump
4 L/R Diffusion
Display
64th/3 – 4thx6
64th/3 – 4thx6
-63 – +63
L, R, L&R
0 – 1.0
6
table #3
table #3
WHITE ROOM
TUNNEL
CANYON
BASEMENT (Reverb, Variation, Insertion block)
No.
1
2
3
4
5
6
7
8
9
10
No.
1
2
3
4
5
●
No.
1
2
3
4
5
6
7
8
9
10
Parameter
LFO Frequency
LFO Depth
Feedback Level
Delay Offset
Display
0.00Hz – 39.7Hz
0 – 127
-63 – +63
0.0ms – 50ms
Value
0 – 127
0 – 127
1 – 127
0 – 127
EQ Low Frequency
EQ Low Gain
EQ High Frequency
EQ High Gain
Dry/Wet
32Hz – 2.0kHz
-12 – +12dB
500Hz – 16.0kHz
-12 – +12dB
D63>W – D=W – D<W63
4 – 40
52 – 76
28 – 58
52 – 76
1 – 127
table #3
100Hz – 10.0kHz
14 – 54
table #3
11 EQ Mid Frequency
(variation block)
12 EQ Mid Gain
(variation block)
13 EQ Mid Width
(variation block)
14 LFO Phase
Difference
15
16
-12 – +12dB
52 – 76
1.0 – 12.0
10 – 120
-180 – +180deg
(resolution=3deg.)
4 – 124
See Table Control
table #1
table #2
table #3
●
Effect Parameter List
SYMPHONIC 1, 2 (Chorus, Variation, Insertion block)
No.
1
2
3
4
5
6
7
8
9
10
TREMOLO 1, 2, 3 (Variation, Insertion block)
Parameter
LFO Frequency
LFO Depth
Delay Offset
Display
0.00Hz – 39.7Hz
0 – 127
0.0ms – 50ms
Value
0 – 127
0 – 127
0 – 127
EQ Low Frequency
EQ Low Gain
EQ High Frequency
EQ High Gain
Dry/Wet
32Hz – 2.0kHz
-12 – +12dB
500Hz – 16.0kHz
-12 – +12dB
D63>W – D=W – D<W63
4 – 40
52 – 76
28 – 58
52 – 76
1 – 127
table #3
table #3
11 EQ Mid Frequency
(variation block)
12 EQ Mid Gain
(variation block)
13 EQ Mid Width
(variation block)
14
15
16
See Table Control
table #1
table #2
table #3
●
No.
1
2
3
4
5
6
7
8
9
10
Parameter
LFO Frequency
AM Depth
PM Depth
Display
0.00Hz – 39.7Hz
0 – 127
0 – 127
Value
0 – 127
0 – 127
0 – 127
See Table Control
table #1
●
EQ Low Frequency
EQ Low Gain
EQ High Frequency
EQ High Gain
32Hz – 2.0kHz
-12 – +12dB
500Hz – 16.0kHz
-12 – +12dB
4 – 40
52 – 76
28 – 58
52 – 76
table #3
11
EQ Mid Frequency
(variation block)
EQ Mid Gain
(variation block)
EQ Mid Width
(variation block)
LFO Phase
Difference
Input Mode
100Hz – 10.0kHz
14 – 54
table #3
-12 – +12dB
52 – 76
100Hz – 10.0kHz
14 – 54
-12 – +12dB
52 – 76
12
1.0 – 12.0
10 – 120
13
14
15
16
1.0 – 12.0
10 – 120
-180 – +180deg
(resolution=3deg.)
mono/stereo
4 – 124
table #3
0–1
ROTARY SPEAKER 2 (Variation, Insertion block)
Parameter
LFO Frequency
LFO Depth
Display
0.00Hz – 39.7Hz
0 – 127
Value
0 – 127
0 – 127
See Table Control
table #1
●
EQ Low Frequency
EQ Low Gain
EQ High Frequency
EQ High Gain
Dry/Wet
32Hz – 2.0kHz
-12 – +12dB
500Hz – 16.0kHz
-12 – +12dB
D63>W – D=W – D<W63
4 – 40
52 – 76
28 – 58
52 – 76
1 – 127
table #3
100Hz – 10.0kHz
14 – 54
table #3
11 EQ Mid Frequency
(variation block)
12 EQ Mid Gain
(variation block)
13 EQ Mid Width
(variation block)
14
15
16
-12 – +12dB
52 – 76
1.0 – 12.0
10 – 120
table #3
AUTO PAN 1, 2, 3 (Variation, Insertion block)
No.
1
2
3
4
Parameter
LFO Frequency
L/R Depth
F/R Depth
PAN Direction
Display
0.00Hz – 39.7Hz
0 – 127
0 – 127
L <–> R, L –> R, L <– R,
Lturn, Rturn, L/R
Value
0 – 127
0 – 127
0 – 127
0–5
See Table Control
table #1
●
5
6
7
8
9
10
EQ Low Frequency
EQ Low Gain
EQ High Frequency
EQ High Gain
32Hz – 2.0kHz
-12 – +12dB
500Hz – 16.0kHz
-12 – +12dB
4 – 40
52 – 76
28 – 58
52 – 76
table #3
100Hz – 10.0kHz
14 – 54
table #3
-12 – +12dB
52 – 76
1.0 – 12.0
10 – 120
11 EQ Mid Frequency
(variation block)
12 EQ Mid Gain
(variation block)
13 EQ Mid Width
(variation block)
14
15
16
table #3
Appendix
No.
1
2
3
4
5
6
7
8
9
10
DISTORTION+ROTARY SPEAKER
OVERDRIVE+ROTARY SPEAKER (Variation, Insertion block)
No.
1
2
3
4
5
6
7
8
9
10
Parameter
LFO Frequency
LFO Depth
Display
0.00Hz – 39.7Hz
0 – 127
Value
0 – 127
0 – 127
EQ Low Frequency
EQ Low Gain
EQ High Frequency
EQ High Gain
Dry/Wet
32Hz – 2.0kHz
-12 – +12dB
500 – 16.0kHz
-12 – +12dB
D63>W – D=W – D<W63
4 – 40
52 – 76
28 – 58
52 – 76
1 – 127
11
12
13
14 Drive
15 LPF Cuttoff
16 Output Level
See Table Control
●
0 – 127
1kHz – Thru
0 – 127
0 – 127
34 – 60
0 – 127
Parameter
LFO Frequency
LFO Depth
AMP Type
Display
0.00Hz – 39.7Hz
0 – 127
Off, Stack, Combo, Tube
Value
0 – 127
0 – 127
0–3
EQ Low Frequency
EQ Low Gain
EQ High Frequency
EQ High Gain
Dry/Wet
32Hz – 2.0kHz
-12 – +12dB
500Hz – 16.0kHz
-12 – +12dB
D63>W – D=W – D<W63
4 – 40
52 – 76
28 – 58
52 – 76
1 – 127
11
12
13
14 Drive
15 LPF Cuttoff
16 Output Level
No.
1
2
3
4
5
6
7
8
9
10
Parameter
LFO Frequency
LFO Depth
Phase Shift Offset
Feedback Level
Display
0.00Hz – 39.7Hz
0 – 127
0 – 127
-63 – +63
Value
0 – 127
0 – 127
0 – 127
1 – 127
See Table Control
table #1
EQ Low Frequency
EQ Low Gain
EQ High Frequency
EQ High Gain
Dry/Wet
32Hz – 2.0kHz
-12 – +12dB
500Hz – 16.0kHz
-12 – +12dB
D63>W – D=W – D<W63
4 – 40
52 – 76
28 – 58
52 – 76
1 – 127
table #3
4 – 22 (chorus, variation
block)
4 – 12 (insertion block)
mono/stereo
4 – 22
11 Stage
12 Diffusion
13
14
15
16
AMP SIM.+ROTARY SPEAKER (Variation, Insertion block)
No.
1
2
3
4
5
6
7
8
9
10
PHASER 1, 3 (Chorus, Variation, Insertion block)
0 – 127
1kHz – Thru
0 – 127
0 – 127
34 – 60
0 – 127
See Table Control
●
table #3
●
4 – 12
0–1
PHASER 2 (Chorus, Variation, Insertion block)
No.
1
2
3
4
5
6
7
8
9
10
Parameter
LFO Frequency
LFO Depth
Phase Shift Offset
Feedback Level
Display
0.00Hz – 39.7Hz
0 – 127
0 – 127
-63 – +63
Value
0 – 127
0 – 127
0 – 127
1 – 127
See Table Control
table #1
EQ Low Frequency
EQ Low Gain
EQ High Frequency
EQ High Gain
Dry/Wet
32Hz – 2.0kHz
-12 – +12dB
500Hz – 16.0kHz
-12 – +12dB
D63>W – D=W – D<W63
4 – 40
52 – 76
28 – 58
52 – 76
1 – 127
table #3
3 – 11
3–6
-180deg – +180deg
(resolution=3deg.)
4 – 124
11 Stage
12
13 LFO Phase
Difference
14
15
16
table #3
●
CP300 Owner’s Manual
117
Effect Parameter List
DISTORTION
OVERDRIVE (Variation, Insertion block)
No.
1
2
3
4
5
6
7
8
9
10
Parameter
Drive
EQ Low Frequency
EQ Low Gain
LPF Cutoff
Output Level
0 – 127
32Hz – 2.0kHz
-12 – +12dB
1.0k – Thru
0 – 127
Value
0 – 127
4 – 40
52 – 76
34 – 60
0 – 127
EQ Mid Frequency
EQ Mid Gain
EQ Mid Width
Dry/Wet
100Hz – 10.0kHz
-12 – +12dB
1.0 – 12.0
D63>W – D=W – D<W63
14 – 54 table #3
52 – 76
10 – 120
1 – 127
0 – 127
0 – 127
11 Edge (Clip Curve)
12
13
14
15
16
Display
STEREO AMP SIMULATOR (Variation, Insertion block)
See Table
Control
●
table #3
table #3
No.
1
2
3
4
5
6
7
8
9
10
Parameter
Drive
AMP Type
LPF Cuttoff
Output Level
Display
0 – 127
Off, Stack, Combo, Tube
1kHz – Thru
0 – 127
Value
0 – 127
0–3
34 – 60
0 – 127
Dry/Wet
D63>W – D=W – D<W63
1 – 127
0 – 127
0 – 127
11 Edge (Clip Curve)
12
13
14
15
16
mild – sharp
See Table
Control
●
Display
-12 – +12dB
100Hz – 10.0kHz
-12 – +12dB
1.0 – 12.0
-12 – +12dB
50Hz – 2.0kHz
500Hz – 16.0kHz
Value
See Table
52 – 76
14 – 54 table #3
52 – 76
10 – 120
52 – 76
8 – 40
table #3
28 – 58 table #3
Control
mono/stereo
0–1
3BAND EQ (Variation, Insertion block)
COMP+DIST (Variation, Insertion block)
No.
1
2
3
4
5
6
7
8
9
10
Parameter
Drive
EQ Low Frequency
EQ Low Gain
LPF Cutoff
Output Level
Display
0 – 127
32Hz – 2.0kHz
-12 – +12dB
1.0k – Thru
0 – 127
Value
0 – 127
4 – 40
52 – 76
34 – 60
0 – 127
See Table
EQ Mid Frequency
EQ Mid Gain
EQ Mid Width
Dry/Wet
100Hz – 10.0kHz
-12 – +12dB
1.0 – 12.0
D63>W – D=W – D<W63
14 – 54 table #3
52 – 76
10 – 120
1 – 127
11
12
13
14
15
16
Edge (Clip Curve)
Attack
Release
Threshold
Ratio
0 – 127
1ms – 40ms
10ms – 680ms
-48dB – -6dB
1.0 – 20.0
0 – 127
0 – 19
0 – 15
79 – 121
0–7
Control
●
table #3
table #3
No.
1
2
3
4
5
6
7
8
9
10
Parameter
EQ Low Gain
EQ Mid Frequency
EQ Mid Gain
EQ Mid Width
EQ High Gain
EQ Low Frequency
EQ High Frequency
11
12
13
14
15 Input Mode
16
mild – sharp
table #8
table #9
table #10
2BAND EQ (Variation, Insertion block)
STEREO DISTORTION
STEREO OVER DRIVE (Variation, Insertion block)
Appendix
No.
1
2
3
4
5
6
7
8
9
10
Parameter
Drive
EQ Low Frequency
EQ Low Gain
LPF Cuttoff
Output Level
Display
0 – 127
32Hz – 2.0kHz
-12 – +12dB
1kHz – Thru
Value
0 – 127
4 – 40
52 – 76
34 – 60
0 – 127
EQ Mid Frequency
EQ Mid Gain
EQ Mid Width
Dry/Wet
100Hz – 10.0kHz
-12 – +12dB
1 – 12
D63>W – D=W – D<W63
14 – 54 table #3
52 – 76
10 – 120
1 – 127
0 – 127
0 – 127
11 Edge (Clip Curve)
12
13
14
15
16
See Table Control
●
table #3
No.
1
2
3
4
5
6
7
8
9
10
Parameter
EQ Low Frequency
EQ Low Gain
EQ High Frequency
EQ High Gain
Display
32Hz – 2.0kHz
-12 – +12dB
500Hz – 16.0kHz
-12 – +12dB
Value
4 – 40
52 – 76
28 – 58
52 – 76
See Table
table #3
Control
table #3
11
12
13
14
15
16
AUTO WAH 1, 2 (Variation, Insertion block)
AMP SIMULATOR (Variation, Insertion block)
No.
1
2
3
4
5
6
7
8
9
10
Parameter
Drive
AMP Type
LPF Cutoff
Output Level
Dry/Wet
11 Edge (Clip Curve)
12
13
14
15
16
118
Display
0 – 127
Off, Stack, Combo, Tube
1.0k – Thru
0 – 127
Value
0 – 127
0–3
34 – 60
0 – 127
D63>W – D=W – D<W63
1 – 127
0 – 127
0 – 127
CP300 Owner’s Manual
See Table
table #3
mild – sharp
Control
●
No.
Parameter
1 LFO Frequency
2 LFO Depth
3 Cutoff Frequency
Offset
4 Resonance
5
6 EQ Low Frequency
7 EQ Low Gain
8 EQ High Frequency
9 EQ High Gain
10 Dry/Wet
Display
0.00Hz – 39.7Hz
0 – 127
0 – 127
Value
0 – 127
0 – 127
0 – 127
1.0 – 12.0
10 – 120
32Hz – 2.0kHz
-12 – +12dB
500Hz – 16.0kHz
-12 – +12dB
D63>W – D=W – D<W63
4 – 40
52 – 76
28 – 58
52 – 76
1 – 127
11 Drive (variation block) 0 – 127
12
13
14
15
16
0 – 127
See Table Control
table #1
●
table #3
table #3
Effect Parameter List
AUTO WAH+DIST
AUTO WHA+ODRV (Variation, Insertion block)
No.
Parameter
1 LFO Frequency
2 LFO Depth
3 Cutoff Frequency
Offset
4 Resonance
5
6 EQ Low Frequency
7 EQ Low Gain
8 EQ High Frequency
9 EQ High Gain
10 Dry/Wet
Display
0.00Hz – 39.7Hz
0 – 127
0 – 127
11 Drive
12 EQ Low Gain
(distortion)
13 EQ Mid Gain
(distortion)
14 LPF Cutoff
15 Output Level
16
TOUCH WAH 1
TOUCH WAH+DIST (Variation, Insertion block)
Value
0 – 127
0 – 127
0 – 127
1.0 – 12.0
10 – 120
32Hz – 2.0kHz
-12 – +12dB
500Hz – 16.0kHz
-12 – +12dB
D63>W – D=W – D<W63
4 – 40
52 – 76
28 – 58
52 – 76
1 – 127
0 – 127
-12 – +12dB
0 – 127
52 – 76
-12 – +12dB
52 – 76
1.0kHz – thru
0 – 127
34 – 60
0 – 127
See Table Control
table #1
●
table #3
table #3
No.
Parameter
1 Sensitive
2 Cutoff Frequency
Offset
3 Resonance
4
5
6 EQ Low Frequency
7 EQ Low Gain
8 EQ High Frequency
9 EQ High Gain
10 Dry/Wet
0 – 127
0 – 127
Display
Value
0 – 127
0 – 127
1.0 – 12.0
10 – 120
32Hz – 2.0kHz
-12 – +12dB
500Hz – 16.0kHz
-12 – +12dB
D63>W – D=W – D<W63
4 – 40
52 – 76
28 – 58
52 – 76
1 – 127
11 Drive (variation block) 0 – 127
12
13
14
15
16
table #3
See Table Control
●
table #3
table #3
0 – 127
TOUCH WAH 2
TOUCH WAH+ODRV (Variation, Insertion block)
No.
1
2
3
4
5
6
7
8
9
10
Parameter
Pitch
Initial Delay
Fine 1
Fine 2
Feedback Level
Display
-24 – +24
0.1ms – 400.0ms
-50 – +50
-50 – +50
-63 – +63
Value
See Table Control
40 – 88
0 – 127 table #7
14 – 114
14 – 114
1 – 127
Dry/Wet
D63>W – D=W – D<W63
1 – 127
11
12
13
14
15
16
Pan 1
Output Level 1
Pan 2
Output Level 2
L63 – R63
0 – 127
L63 – R63
0 – 127
1 – 127
0 – 127
1 – 127
0 – 127
●
PITCH CHANGE 2 (Variation, Insertion block)
No.
1
2
3
4
5
6
7
8
9
10
Parameter
Pitch
Initial Delay
Fine 1
Fine 2
Feedback Level
Display
-24 – +24
0.1ms – 400.0ms
-50 – +50cent
-50 – +50cent
-63 – +63
Value
See Table Control
40 – 88
0 – 127 table #7
14 – 114
14 – 114
1 – 127
Dry/Wet
D63>W – D=W – D<W63
1 – 127
11
12
13
14
15
16
Pan 1
Output Level 1
Pan 2
Output Level 2
L63 – R63
0 – 127
L63 – R63
0 – 127
1 – 127
0 – 127
1 – 127
0 – 127
●
HARMONIC ENHANCER (Variation, Insertion block)
No.
Parameter
1 HPF Cutoff
2 Drive
3 Mix Level
4
5
6
7
8
9
10
11
12
13
14
15
16
Display
500Hz – 16.0kHz
0 – 127
0 – 127
Value
28 – 58
0 – 127
0 – 127
See Table Control
No.
Parameter
1 Sensitive
2 Cutoff Frequency
Offset
3 Resonance
4
5
6 EQ Low Frequency
7 EQ Low Gain
8 EQ High Frequency
9 EQ High Gain
10 Dry/Wet
Display
11 Drive (variation block)
12 EQ Low Gain
(variation block)
(distortion)
13 EQ Mid Gain
(variation block)
(distortion)
14 LPF Cutoff (variation
block)
15 Output Level
(variation block)
16 Release (variation
block)
0 – 127
0 – 127
Value
0 – 127
0 – 127
1.0 – 12.0
10 – 120
32Hz – 2.0kHz
-12 – +12dB
500Hz – 16.0kHz
-12 – +12dB
D63>W – D=W – D<W63
4 – 40
52 – 76
28 – 58
52 – 76
1 – 127
0 – 127
-12 – +12dB
0 – 127
52 – 76
-12 – +12dB
52 – 76
1.0kHz – thru
34 – 60
0 – 127
0 – 127
10 – 680ms
52 – 67
See Table Control
●
table #3
table #3
table #3
Appendix
PITCH CHANGE 1 (Variation, Insertion block)
table #12
COMPRESSOR 1, 2 (Variation, Insertion block)
No.
1
2
3
4
5
6
7
8
9
10
Parameter
Attack
Release
Threshold
Ratio
Output Level
Display
1 – 40ms
10 – 680ms
-48 – -6dB
1.0 – 20.0
0 – 127
Value
See Table Control
0 – 19
table #8
0 – 15
table #9
79 – 121
0–7
table #10
0 – 127
11
12
13
14
15
16
NOISE GATE (Variation, Insertion block)
No.
1
2
3
4
5
6
7
8
9
10
Parameter
Attack
Release
Threshold
Output Level
Display
1 – 40ms
10 – 680ms
-72 – -30dB
0 – 127
Value
0 – 19
0 – 15
55 – 97
0 – 127
See Table Control
table #8
table #9
11
12
13
14
15
16
CP300 Owner’s Manual
119
Effect Parameter List
VOICE CANCEL (Variation, Insertion block)
No.
1
2
3
4
5
6
7
8
9
10
Parameter
11 Low Adjust
12 High Adjust
13
14
15
16
ENSEMBLE DETUNE (Chorus, Variation, Insertion block)
Display
0 – 26
0 – 26
Value
See Table Control
0 – 26
0 – 26
2WAY ROTARY SPEAKER (Variation, Insertion block)
No.
1
2
3
4
5
6
7
8
9
10
Display
0.0Hz – 39.7Hz
0 – 127
0 – 127
L63>H – L=H – L<H63
Value
0 – 127
0 – 127
0 – 127
1 – 127
See Table Control
table #1
●
EQ Low Frequency
EQ Low Gain
EQ High Frequency
EQ High Gain
32Hz – 2.0kHz
-12 – +12dB
500Hz – 16.0kHz
-12 – +12dB
4 – 40
52 – 76
28 – 58
52 – 76
table #3
14 – 54
0 – 60
Parameter
Detune
Lch Init Delay
Rch Init Delay
Display
-50 – +50cent
0.0mS – 50mS
0.0mS – 50mS
Value
See Table Control
14 – 114
0 – 127 table #2
0 – 127 table #2
Dry/Wet
D63>W – D=W – D<W63
1 – 127
11
12
13
14
15
16
EQ Low Frequency
EQ Low Gain
EQ High Frequency
EQ High Gain
32Hz – 2.0kHz
-12 – +12dB
500Hz – 16.0kHz
-12 – +12dB
4 – 40
52 – 76
28 – 58
52 – 76
table #3
●
table #3
AMBIENCE (Variation, Insertion block)
Parameter
Rotor Speed
Drive Low
Drive High
Low/High
11 Crossover Frequency 100Hz – 10.0kHz
12 Mic L – R Angle
0deg – 180deg
(resolution=3deg.)
13
14
15
16
No.
1
2
3
4
5
6
7
8
9
10
table #3
No.
1
2
3
4
5
6
7
8
9
10
Parameter
Delay Time
Output Phase
Display
0.0mS – 50mS
normal/inverse
Value
0 – 127
0–1
See Table Control
table #2
EQ Low Frequency
EQ Low Gain
EQ High Frequency
EQ High Gain
Dry/Wet
32Hz – 2.0kHz
-12 – +12dB
500Hz – 16.0kHz
-12 – +12dB
D63>W – D=W – D<W63
4 – 40
52 – 76
28 – 58
52 – 76
1 – 127
table #3
Value
0–4
1 – 62
0 – 127
0 – 127
See Table Control
●
Display
44.1kHz – 345Hz
Value
0 – 127
See Table Control
table #13
1 – 127
0 – 18
10 – 60
0–5
LPF Resonance
Bit Assign
Emphasis
1 – 127
-6 – +12dB
63Hz – Thru
Thru, PowerBass, Radio,
Tel, Clean, Low
1.0 – 12.0
0–6
Off/On
Dry/Wet
D63>W – D=W – D<W63
1 – 127
table #3
●
11
12
13
14
15
16
table #3
TALKING MODULATION (Variation, Insertion block)
DIST+2WAY ROTARY SPEAKER
OD+2WAY ROTARY SPEAKER (Variation, Insertion block)
Appendix
No.
1
2
3
4
5
6
7
8
9
10
Parameter
Rotor Speed
Drive Low
Drive High
Low/High Balance
Display
0.0 – 39.7Hz
0 – 127
0 – 127
L63>H – L=H – L<H63
Value
0 – 127
0 – 127
0 – 127
1 – 127
EQ Low Frequency
EQ Low Gain
EQ High Frequency
EQ High Gain
32 – 2.0kHz
-12 – +12dB
500Hz – 16.0kHz
-12 – +12dB
4 – 40
52 – 76
28 – 58
52 – 76
11
12
13
14
15
16
Crossover Frequency 100Hz – 10.0kHz
Mic L – R Angle
0 – 180deg
14 – 54
0 – 60
Drive
LPF Cuttoff
Output Level
0 – 127
34 – 60
0 – 127
1kHz – Thru
See Table
Control
●
No.
1
2
3
4
5
6
7
8
9
10
Parameter
Vowel
Move speed
Drive
Output Level
Display
a, i, u, e, o
1 – 62
0 – 127
0 – 127
11
12
13
14
15
16
LO-FI (Variation, Insertion block)
AMP SIM.+2WAY ROTARY SP (Variation, Insertion block)
No.
1
2
3
4
5
6
7
8
9
10
Parameter
Rotor Speed
Drive Low
Drive High
Low/High Balance
Display
0.0 – 39.7Hz
0 – 127
0 – 127
L63>H – L=H – L<H63
Value
0 – 127
0 – 127
0 – 127
1 – 127
EQ Low Frequency
EQ Low Gain
EQ High Frequency
EQ High Gain
32Hz – 2.0kHz
-12 – +12dB
500Hz – 16.0kHz
-12 – +12dB
4 – 40
52 – 76
28 – 58
52 – 76
11 Crossover Frequency
12 Mic L – R Angle
13 AMP Type
14 Drive
15 LPF Cuttoff
16 Output Level
120
100Hz – 10.0kHz
0 – 180deg
Off, Stack, Combo,
Tube (AMPSIM only)
1kHz – Thru
CP300 Owner’s Manual
14 – 54
0 – 60
0–3
0 – 127
34 – 60
0 – 127
See Table Control
●
No.
Parameter
1 Sampling Freq
Control
2 Word Length
3 Output Gain
4 LPF Cutoff
5 Filter Type
6
7
8
9
10
11
12
13
14
15 Input Mode
16
mono/stereo
table #3
10 – 120
0–6
0–1
●
Effect Parameter List
DIST+DELAY
OVERDRIVE+DELAY (Variation, Insertion block)
No.
Parameter
1 Lch Delay Time
2 Rch Delay Time
3 Delay Feedback
Time
4 Delay Feedback
Level
5 Delay Mix
6 Dist Drive
7 Dist Output Level
8 Dist EQ Low Gain
9 Dist EQ Mid Gain
10 Dry/Wet
V DISTORTION HARD+DELAY
V DISTORTION SOFT+DELAY (Variation, Insertion block)
Display
0.1 – 1638.3ms
0.1 – 1638.3ms
0.1 – 1638.3ms
Value
1 – 16383
1 – 16383
1 – 16383
-63 – +63
1 – 127
0 – 127
0 – 127
0 – 127
-12 – +12dB
-12 – +12dB
D63>W – D=W – D<W63
0 – 127
0 – 127
0 – 127
52 – 76
52 – 76
1 – 127
See Table Control
No.
Parameter
1 Overdrive
2 Device
3
Speaker
4
5
6
7
8
●
11
12
13
14
15
16
Presence
Output Level
Delay Time L
Delay Time R
Delay Feedback
Time
9 Delay Feedback
Level
10 Dry/Wet Balance
11 Delay Mix
12
13
14
15
16
Display
0 – 100%
Transistor/Vintage Tube/
Dist1/Dist2/Fuzz
Flat/Stack/Combo/Twin/
Radio/Megaphone
0 – 20
0 – 100%
0.1ms – 1486.0ms
0.1ms – 1486.0ms
0.1ms – 1486.0ms
Value
0 – 100
0–4
See Table Control
0–5
0 – 20
0 – 100
1 – 14860
1 – 14860
1 – 14860
-63 – +63
1 – 127
D63>W – D=W – D<W63
1 – 127
0 – 127
0 – 127
●
COMP+DIST+DELAY
COMP+OVERDRIVE+DELAY (Variation, Insertion block)
Display
0.1 – 1638.3ms
-63 – +63
Value
1 – 16383
1 – 127
0 – 127
0 – 127
0 – 127
-12 – +12dB
-12 – +12dB
0 – 127
0 – 127
0 – 127
52 – 76
52 – 76
D63>W – D=W – D<W63
1 – 127
11
12
13
14
15
16
1ms – 40ms
10ms – 680ms
-48dB – -6dB
1.0 – 20.0
0 – 19
0 – 15
79 – 121
0–7
Comp. Attack
Comp. Release
Comp. Threshold
Comp. Ratio
See Table Control
●
table #8
table #9
table #10
11 Wah Sensitive
12 Wah Cutoff Freq
Offset
13 Wah Resonance
14 Wah Release
15
16
Display
0.1 – 1638.3ms
-63 – +63
Value
1 – 16383
1 – 127
0 – 127
0 – 127
0 – 127
-12 – +12dB
-12 – +12dB
0 – 127
0 – 127
0 – 127
52 – 76
52 – 76
D63>W – D=W – D<W63
1 – 127
0 – 127
0 – 127
0 – 127
0 – 127
1.0 – 12.0
10 – 680ms
10 – 120
52 – 67
See Table Control
●
3
Speaker
4 Presence
5 Output Level
6
7
8
9
10 Dry/Wet Balance
11
12
13
14
15
16
Display
0 – 100%
Transistor/Vintage Tube/
Dist1/Dist2/Fuzz
Flat/Stack/Combo/Twin/
Radio/Megaphone
0 – 20
0 – 100%
D63>W – D=W – D<W63
Value
0 – 100
0–4
Display
0.0 – 2.65Hz
0.0 – 2.65Hz
2.69 – 39.7Hz
2.69 – 39.7Hz
0 – 127
0 – 127
0 – 127
0 – 127
L63>H – L=H – L<H=63
Value
0 – 63
0 – 63
64 – 127
64 – 127
0 – 127
0 – 127
0 – 127
0 – 127
1 – 127
See Table Control
table #1
table #1
table #1
table #1
11
12
13
14
15
16
EQ Low Frequency
EQ Low Gain
EQ High Frequency
EQ High Gain
Mic L-R Angle
Speed Control
32Hz – 2.0kHz
-12 – +12dB
500Hz – 16.0kHz
-12 – +12dB
0 – 180deg
Slow/Fast
4 – 40
52 – 76
28 – 58
52 – 76
0 – 60
0/1
table #3
table #3
●
No.
Parameter
1 Delay Time
2 Delay Feedback
Level
3 Delay Mix
4 Dist Drive
5 Dist Output Level
6 Dist EQ Low Gain
7 Dist EQ High Gain
8 L/R Diffusion
9
Lag
Display
64th/3 – 4thx6
-63 – +63
Value
0 – 19
1 – 127
0 – 127
0 – 127
0 – 127
-12 – +12dB
-12 – +12dB
1 (-63ms) – 64 (0ms) –
127 (63ms)
1 (-63ms) – 64 (0ms) –
127 (63ms)
D63>W – D=W – D<W63
0 – 127
0 – 127
0 – 127
52 – 76
52 – 76
1 – 127
See Table Control
table #14
1 – 127
1 – 127
●
11
12
13
14
15
16
table #12
See Table Control
0–5
0 – 20
0 – 100
1 – 127
Parameter
Rotor Speed Slow
Horn Speed Slow
Rotor Speed Fast
Horn Speed Fast
Slow-Fast Time of R
Slow-Fast Time of H
Drive Low
Drive High
Low/High Balance
10 Dry/Wet
V DISTORTION HARD
V DISTORTION SOFT (Variation, Insertion block)
No.
Parameter
1 Overdrive
2 Device
No.
1
2
3
4
5
6
7
8
9
10
DIST+TEMPO DELAY
OVERDRIVE+TEMPO DELAY (Variation, Insertion block)
WAH+DIST+DELAY
WAH+OVERDRIVE+DELAY (Variation, Insertion block)
No.
Parameter
1 Delay Time
2 Delay Feedback
Level
3 Delay Mix
4 Dist Drive
5 Dist Output Level
6 Dist EQ Low Gain
7 Dist EQ Mid Gain
8
9
10 Dry/Wet
DUAL ROTOR SPEAKER1, 2 (Variation, Insertion block)
Appendix
No.
Parameter
1 Delay Time
2 Delay Feedback
Level
3 Delay Mix
4 Dist Drive
5 Dist Output Level
6 Dist EQ Low Gain
7 Dist EQ Mid Gain
8
9
10 Dry/Wet
●
COMP+DIST+TEMPO DELAY
COMP+OD+TEMPO DELAY (Variation, Insertion block)
No.
Parameter
1 Delay Time
2 Delay Feedback
Level
3 Delay Mix
4 Dist Drive
5 Dist Output Level
6 Dist EQ Low Gain
7 Dist EQ High Gain
8 L/R Diffusion
9
Lag
10 Dry/Wet
11
12
13
14
15
16
Comp. Attack
Comp. Release
Comp. Threshold
Comp. Ratio
Display
64th/3 – 4thx6
-63 – +63
Value
0 – 19
1 – 127
0 – 127
0 – 127
0 – 127
-12 – +12dB
-12 – +12dB
1 (-63ms) – 64 (0ms) –
127 (63ms)
1 (-63ms) – 64 (0ms) –
127 (63ms)
D63>W – D=W – D<W63
0 – 127
0 – 127
0 – 127
52 – 76
52 – 76
1 – 127
1ms – 40ms
10ms – 680ms
-48dB – -6dB
1.0 – 20.0
See Table Control
table #14
1 – 127
1 – 127
●
0 – 19
0 – 15
79 – 121
0–7
CP300 Owner’s Manual
121
Effect Parameter List
WAH+DIST+TEMPO DELAY
WAH+OD+TEMPO DELAY (Variation, Insertion block)
No.
Parameter
1 Delay Time
2 Delay Feedback
Level
3 Delay Mix
4 Dist Drive
5 Dist Output Level
6 Dist EQ Low Gain
7 Dist EQ High Gain
8 L/R Diffusion
9
Lag
10 Dry/Wet
11 Wah Sensitive
12 Wah Cutoff Freq
Offset
13 Wah Resonance
14 Wah Release
15
16
Display
64th/3 – 4thx6
-63 – +63
Value
0 – 19
1 – 127
0 – 127
0 – 127
0 – 127
-12 – +12dB
-12 – +12dB
1 (-63ms) – 64 (0ms) –
127 (63ms)
1 (-63ms) – 64 (0ms) –
127 (63ms)
D63>W – D=W – D<W63
0 – 127
0 – 127
0 – 127
52 – 76
52 – 76
1 – 127
See Table Control
table #14
1 – 127
●
1 – 127
0 – 127
0 – 127
0 – 127
0 – 127
1.0 – 12.0
10 – 680mS
10 – 120
52 – 67
V DIST HARD+TEMPO DELAY
V DIST SOFT+TEMPO DELAY (Variation, Insertion block)
No.
Parameter
1 Overdrive
2 Device
3
Speaker
4
5
6
7
8
Presence
Output Level
Delay Time
Delay Feedback
Level
L/R Diffusion
9
Lag
10 Dry/Wet Balance
Appendix
11 Delay Mix
12
13
14
15
16
Display
0 – 100%
Transistor/Vintage Tube/
Dist1/Dist2/Fuzz
Flat/Stack/Combo/Twin/
Radio/Megaphone
0 – 20
0 – 100%
64th/3 – 4thx6
-63 – +63
Value
0 – 100
0–4
See Table Control
0–5
0 – 20
0 – 100
0 – 19
1 – 127
1 (-63ms) – 64 (0ms) –
127 (63ms)
1 (-63ms) – 64 (0ms) –
127(63ms)
D63>W – D=W – D<W63
1 – 127
0 – 127
0 – 127
table #14
1 – 127
●
1 – 127
VIBE ROTOR (Variation, Insertion block)
No.
1
2
3
4
5
6
7
8
9
10
Parameter
Vibrate Speed
Vibrate Depth (AM)
Vibrate Depth (PM)
Display
0.00Hz – 39.7Hz
0 – 127
0 – 127
Value
0 – 127
0 – 127
0 – 127
See Table Control
table #1
EQ Low Frequency
EQ Low Gain
EQ High Frequency
EQ High Gain
Dry/Wet Balance
32Hz – 2.0kHz
-12 – +12dB
500Hz – 16.0kHz
-12 – +12dB
D63>W – D=W – D<W63
4 – 40
52 – 76
28 – 58
52 – 76
1 – 127
table #3
-180 – +180deg
(resolution=3deg.)
mono/stereo
OFF, ON
4 – 124
11
12
13
14 LFO Phase
Difference
15 Input Mode
16 Vibrate SW
0–1
0–1
table #3
●
NO EFFECT (Reverb, Chorus, Variation)
THRU (Insertion block)
No.
1
2
3
4
5
6
7
8
9
10
Parameter
Display
Value
11
12
13
14
15
16
* Parameter 10 Dry/Wet only affects insertion type effects.
122
CP300 Owner’s Manual
See Table Control
Effect Data Assign Table
Data
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
Value
0.00
0.04
0.08
0.13
0.17
0.21
0.25
0.29
0.34
0.38
0.42
0.46
0.51
0.55
0.59
0.63
0.67
0.72
0.76
0.80
0.84
0.88
0.93
0.97
1.01
1.05
1.09
1.14
1.18
1.22
1.26
1.30
1.35
1.39
1.43
1.47
1.51
1.56
1.60
1.64
1.68
1.72
1.77
1.81
1.85
1.89
1.94
1.98
2.02
2.06
2.10
2.15
2.19
2.23
2.27
2.31
2.36
2.40
2.44
2.48
2.52
2.57
2.61
2.65
Table #2
Modulation Delay Offset
Data
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
Value
2.69
2.78
2.86
2.94
3.03
3.11
3.20
3.28
3.37
3.45
3.53
3.62
3.70
3.87
4.04
4.21
4.37
4.54
4.71
4.88
5.05
5.22
5.38
5.55
5.72
6.06
6.39
6.73
7.07
7.40
7.74
8.08
8.41
8.75
9.08
9.42
9.76
10.1
10.8
11.4
12.1
12.8
13.5
14.1
14.8
15.5
16.2
16.8
17.5
18.2
19.5
20.9
22.2
23.6
24.9
26.2
27.6
28.9
30.3
31.6
33.0
34.3
37.0
39.7
Data
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
Value
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
2.0
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
3.0
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
4.0
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
5.0
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
5.9
6.0
6.1
6.2
6.3
Data
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
Table #3
EQ Frequency
Value
6.4
6.5
6.6
6.7
6.8
6.9
7.0
7.1
7.2
7.3
7.4
7.5
7.6
7.7
7.8
7.9
8.0
8.1
8.2
8.3
8.4
8.5
8.6
8.7
8.8
8.9
9.0
9.1
9.2
9.3
9.4
9.5
9.6
9.7
9.8
9.9
10.0
11.1
12.2
13.3
14.4
15.5
17.1
18.6
20.2
21.8
23.3
24.9
26.5
28.0
29.6
31.2
32.8
34.3
35.9
37.5
39.0
40.6
42.2
43.7
45.3
46.9
48.4
50.0
Data
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
Value
THRU (0)
22
25
28
32
36
40
45
50
56
63
70
80
90
100
110
125
140
160
180
200
225
250
280
315
355
400
450
500
560
630
700
800
900
1.0k
1.1k
1.2k
1.4k
1.6k
1.8k
2.0k
2.2k
2.5k
2.8k
3.2k
3.6k
4.0k
4.5k
5.0k
5.6k
6.3k
7.0k
8.0k
9.0k
10.0k
11.0k
12.0k
14.0k
16.0k
18.0k
THRU (20.0k)
Table #4
Reverb Time
Data
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
Value
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
1.1
1.2
1.3
1.4
1.5
1.6
1.7
1.8
1.9
2.0
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
3.0
3.1
3.2
3.3
3.4
3.5
3.6
3.7
3.8
3.9
4.0
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
5.0
5.5
6.0
6.5
7.0
7.5
8.0
8.5
9.0
9.5
10.0
11.0
12.0
13.0
14.0
15.0
16.0
Table #5
Delay Time (200.0ms)
Data
64
65
66
67
68
69
Value
17.0
18.0
19.0
20.0
25.0
30.0
Data
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
Value
0.1
1.7
3.2
4.8
6.4
8.0
9.5
11.1
12.7
14.3
15.8
17.4
19.0
20.6
22.1
23.7
25.3
26.9
28.4
30.0
31.6
33.2
34.7
36.3
37.9
39.5
41.0
42.6
44.2
45.7
47.3
48.9
50.5
52.0
53.6
55.2
56.8
58.3
59.9
61.5
63.1
64.6
66.2
67.8
69.4
70.9
72.5
74.1
75.7
77.2
78.8
80.4
81.9
83.5
85.1
86.7
88.2
89.8
91.4
93.0
94.5
96.1
97.7
99.3
Data
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
Value
100.8
102.4
104.0
105.6
107.1
108.7
110.3
111.9
113.4
115.0
116.6
118.2
119.7
121.3
122.9
124.4
126.0
127.6
129.2
130.7
132.3
133.9
135.5
137.0
138.6
140.2
141.8
143.3
144.9
146.5
148.1
149.6
151.2
152.8
154.4
155.9
157.5
159.1
160.6
162.2
163.8
165.4
166.9
168.5
170.1
171.7
173.2
174.8
176.4
178.0
179.5
181.1
182.7
184.3
185.8
187.4
189.0
190.6
192.1
193.7
195.3
196.9
198.4
200.0
CP300 Owner’s Manual
Appendix
Table #1
LFO Frequency
123
Effect Data Assign Table
Table #6
Room Size
Appendix
Data
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
Value
0.1
0.3
0.4
0.6
0.7
0.9
1.0
1.2
1.4
1.5
1.7
1.8
2.0
2.1
2.3
2.5
2.6
2.8
2.9
3.1
3.2
3.4
3.5
3.7
3.9
4.0
4.2
4.3
4.5
4.6
4.8
5.0
5.1
5.3
5.4
5.6
5.7
5.9
6.1
6.2
6.4
6.5
6.7
6.8
7.0
7.2
7.3
7.5
7.6
7.8
7.9
8.1
8.2
8.4
8.6
8.7
8.9
9.0
9.2
9.3
9.5
9.7
9.8
10.0
Table #7
Delay Time (400.0ms)
Data
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
Value
10.1
10.3
10.4
10.6
10.8
10.9
11.1
11.2
11.4
11.5
11.7
11.9
12.0
12.2
12.3
12.5
12.6
12.8
12.9
13.1
13.3
13.4
13.6
13.7
13.9
14.0
14.2
14.4
14.5
14.7
14.8
15.0
15.1
15.3
15.5
15.6
15.8
15.9
16.1
16.2
16.4
16.6
16.7
16.9
17.0
17.2
17.3
17.5
17.6
17.8
18.0
18.1
18.3
18.4
18.6
18.7
18.9
19.1
19.2
19.4
19.5
19.7
19.8
20.0
Data
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
Value
0.1
3.2
6.4
9.5
12.7
15.8
19.0
22.1
25.3
28.4
31.6
34.7
37.9
41.0
44.2
47.3
50.5
53.6
56.8
59.9
63.1
66.2
69.4
72.5
75.7
78.8
82.0
85.1
88.3
91.4
94.6
97.7
100.9
104.0
107.2
110.3
113.5
116.6
119.8
122.9
126.1
129.2
132.4
135.5
138.6
141.8
144.9
148.1
151.2
154.4
157.5
160.7
163.8
167.0
170.1
173.3
176.4
179.6
182.7
185.9
189.0
192.2
195.3
198.5
Data
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
Table #9
Compressor Release Time
Value
201.6
204.8
207.9
211.1
214.2
217.4
220.5
223.7
226.8
230.0
233.1
236.3
239.4
242.6
245.7
248.9
252.0
255.2
258.3
261.5
264.6
267.7
270.9
274.0
277.2
280.3
283.5
286.6
289.8
292.9
296.1
299.2
302.4
305.5
308.7
311.8
315.0
318.1
321.3
324.4
327.6
330.7
333.9
337.0
340.2
343.3
346.5
349.6
352.8
355.9
359.1
362.2
365.4
368.5
371.7
374.8
378.0
381.1
384.3
387.4
390.6
393.7
396.9
400.0
Table #8
Compressor Attack Time
Data
0
1
2
3
4
5
6
7
8
9
124
CP300 Owner’s Manual
Value
1
2
3
4
5
6
7
8
9
10
Data
10
11
12
13
14
15
16
17
18
19
Value
12
14
16
18
20
23
26
30
35
40
Data
0
1
2
3
4
5
6
7
Value
10
15
25
35
45
55
65
75
Data
8
9
10
11
12
13
14
15
Value
85
100
115
140
170
230
340
680
Table #10
Compressor Ratio
Data
0
1
2
3
Value
1.0
1.5
2.0
3.0
Data
4
5
6
7
Value
5.0
7.0
10.0
20.0
Table #11
Reverb Width; Depth; Height
Data
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
Value
0.5
0.8
1.0
1.3
1.5
1.8
2.0
2.3
2.6
2.8
3.1
3.3
3.6
3.9
4.1
4.4
4.6
4.9
5.2
5.4
5.7
5.9
6.2
6.5
6.7
7.0
7.2
7.5
7.8
8.0
8.3
8.6
8.8
9.1
9.4
9.6
9.9
10.2
10.4
10.7
11.0
11.2
11.5
11.8
12.1
12.3
12.6
12.9
13.1
13.4
13.7
14.0
14.2
14.5
14.8
15.1
15.4
15.6
15.9
16.2
16.5
16.8
17.1
17.3
Data
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
Value
17.6
17.9
18.2
18.5
18.8
19.1
19.4
19.7
20.0
20.2
20.5
20.8
21.1
21.4
21.7
22.0
22.4
22.7
23.0
23.3
23.6
23.9
24.2
24.5
24.9
25.2
25.5
25.8
26.1
26.5
26.8
27.1
27.5
27.8
28.1
28.5
28.8
29.2
29.5
29.9
30.2
Table #14
Tempo Delay
Table #12
Wah Release Time
Data
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
Value
10.0
15.0
25.0
35.0
45.0
55.0
65.0
75.0
85.0
100.0
115.0
140.0
170.0
230.0
340.0
680.0
Table #13
Sampling Freq Control
Data
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
Value
44.1K
22.1K
14.7K
11.0K
8.8K
7.4K
6.3K
5.5K
4.9K
4.5K
4.0K
3.7K
3.4K
3.2K
2.9K
2.8K
2.6K
2.5K
2.3K
2.2K
2.1K
2.0K
1.92K
1.84K
1.76K
1.70K
1.63K
1.58K
1.52K
1.47K
1.42K
1.38K
1.34K
1.30K
1.26K
1.23K
1.19K
1.16K
1.13K
1.10K
1.08K
1.05K
1.03K
1.00K
980.0
959.0
938.0
919.0
900.0
882.0
865.0
848.0
832.0
817.0
802.0
788.0
774.0
760.0
747.0
735.0
723.0
711.0
700.0
689.0
Data
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
Value
678.0
668.0
658.0
649.0
639.0
630.0
621.0
613.0
604.0
596.0
588.0
580.0
573.0
565.0
558.0
551.0
544.0
538.0
531.0
525.0
519.0
513.0
507.0
501.0
496.0
490.0
485.0
479.0
474.0
469.0
464.0
459.0
455.0
450.0
445.0
441.0
437.0
432.0
428.0
424.0
420.0
416.0
412.0
408.0
405.0
401.0
397.0
394.0
390.0
387.0
383.0
380.0
377.0
374.0
371.0
368.0
364.0
361.0
359.0
356.0
353.0
350.0
347.0
345.0
Data
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
Value
64th/3
64th.
32th
32th/3
32th.
16th
16th/3
16th.
8th
8th/3
8th.
4th
4th/3
4th.
2nd
2nd/3
2nd.
4thX4
4thX5
4thX6
4thX7
4thX8
4thX9
4thX10
4thX11
4thX12
4thX13
4thX14
4thX15
4thX16
4thX17
4thX18
4thX19
4thX20
4thX21
4thX22
4thX23
4thX24
4thX25
4thX26
4thX27
4thX28
4thX29
4thX30
4thX31
4thX32
4thX33
4thX34
4thX35
4thX36
4thX37
4thX38
4thX39
4thX40
4thX41
4thX42
4thX43
4thX44
4thX45
4thX46
4thX47
4thX48
4thX49
4thX50
Data
64
65
66
67
68
69
70
71
72
73
74
75
76
77
Value
4thX51
4thX52
4thX53
4thX54
4thX55
4thX56
4thX57
4thX58
4thX59
4thX60
4thX61
4thX62
4thX63
4thX64
MIDI Data Format
Decimal
Hexadecimal
Binary
Decimal
Hexadecimal
Binary
Decimal
Hexadecimal
Binary
Decimal
Hexadecimal
Binary
0
00
0000 0000
32
20
0010 0000
64
40
0100 0000
96
60
0110 0000
1
01
0000 0001
33
21
0010 0001
65
41
0100 0001
97
61
0110 0001
2
02
0000 0010
34
22
0010 0010
66
42
0100 0010
98
62
0110 0010
3
03
0000 0011
35
23
0010 0011
67
43
0100 0011
99
63
0110 0011
4
04
0000 0100
36
24
0010 0100
68
44
0100 0100
100
64
0110 0100
5
05
0000 0101
37
25
0010 0101
69
45
0100 0101
101
65
0110 0101
6
06
0000 0110
38
26
0010 0110
70
46
0100 0110
102
66
0110 0110
7
07
0000 0111
39
27
0010 0111
71
47
0100 0111
103
67
0110 0111
8
08
0000 1000
40
28
0010 1000
72
48
0100 1000
104
68
0110 1000
9
09
0000 1001
41
29
0010 1001
73
49
0100 1001
105
69
0110 1001
10
0A
0000 1010
42
2A
0010 1010
74
4A
0100 1010
106
6A
0110 1010
11
0B
0000 1011
43
2B
0010 1011
75
4B
0100 1011
107
6B
0110 1011
12
0C
0000 1100
44
2C
0010 1100
76
4C
0100 1100
108
6C
0110 1100
13
0D
0000 1101
45
2D
0010 1101
77
4D
0100 1101
109
6D
0110 1101
14
0E
0000 1110
46
2E
0010 1110
78
4E
0100 1110
110
6E
0110 1110
15
0F
0000 1111
47
2F
0010 1111
79
4F
0100 1111
111
6F
0110 1111
16
10
0001 0000
48
30
0011 0000
80
50
0101 0000
112
70
0111 0000
17
11
0001 0001
49
31
0011 0001
81
51
0101 0001
113
71
0111 0001
18
12
0001 0010
50
32
0011 0010
82
52
0101 0010
114
72
0111 0010
19
13
0001 0011
51
33
0011 0011
83
53
0101 0011
115
73
0111 0011
20
14
0001 0100
52
34
0011 0100
84
54
0101 0100
116
74
0111 0100
21
15
0001 0101
53
35
0011 0101
85
55
0101 0101
117
75
0111 0101
22
16
0001 0110
54
36
0011 0110
86
56
0101 0110
118
76
0111 0110
23
17
0001 0111
55
37
0011 0111
87
57
0101 0111
119
77
0111 0111
24
18
0001 1000
56
38
0011 1000
88
58
0101 1000
120
78
0111 1000
25
19
0001 1001
57
39
0011 1001
89
59
0101 1001
121
79
0111 1001
26
1A
0001 1010
58
3A
0011 1010
90
5A
0101 1010
122
7A
0111 1010
27
1B
0001 1011
59
3B
0011 1011
91
5B
0101 1011
123
7B
0111 1011
28
1C
0001 1100
60
3C
0011 1100
92
5C
0101 1100
124
7C
0111 1100
29
1D
0001 1101
61
3D
0011 1101
93
5D
0101 1101
125
7D
0111 1101
30
1E
0001 1110
62
3E
0011 1110
94
5E
0101 1110
126
7E
0111 1110
31
1F
0001 1111
63
3F
0011 1111
95
5F
0101 1111
127
7F
0111 1111
Appendix
Many MIDI messages listed in the MIDI Data Format are expressed in decimal numbers, binary numbers and hexadecimal numbers.
Hexadecimal numbers may include the letter “H” as a suffix.
Also, "n" can freely be defined as any whole number. To enter data/values, refer to the table below.
• Except the table above, for example 144-159 (decimal)/9nH/1001 0000-1001 1111 (binary) denotes the Note On Message for each channel
(1-16). 176-191/BnH/1011 0000-1011 1111 denotes the Control Change Message for each channel (1-16). 192-207/CnH/1100 0000-1100
1111 denotes the Program Change Message for each channel (1-16). 240/FOH/1111 0000 denotes the start of a System Exclusive Message.
247/F7H/1111 0111 denotes the end of a System Exclusive Message.
• aaH (hexidecimal)/0aaaaaaa (binary) denotes the data address. The address contains High, Mid, and Low.
• bbH/0bbbbbbb denotes the byte count.
• ccH/0ccccccc denotes the check sum.
• ddH/0ddddddd denotes the data/value.
CP300 Owner’s Manual
125
MIDI Data Format
MIDI CHANNEL MESSAGE (1)
Status byte
MIDI Events
Key Off
Key On
Status
8nH
9nH
(n: Channel
Number)
(n: Channel
Number)
1st Data byte
Data (HEX)
kk
kk
Appendix
126
Key no. (0 – 127)
vv
Key no. (0 – 127)
vv
BnH
CnH
(n: Channel
Number)
CP300 Owner’s Manual
(HEX)
Parameter
Velocity (0 – 127)
Key On:
vv=1 – 127
Key Off: vv=0
Normal
SFX Voice
SFX kit
Drum kit
˛
Ø
˛
˛
Ø
Ø
Ø
Ø
(Keyboard)
Ø
˛
Ø
Ø
Ø
˛
Ø
(Voice)
Ø
˛
Ø
Ø
(Modulation Wheel)
Ø
˛
Ø
˛
Ø
˛
˛
Ø
(VOICE EDIT)
Ø
˛
Ø
Ø
(VOICE EDIT)
Ø
˛
Ø
Ø
(VOICE EDIT)
Ø
˛
Ø
Ø
˛
Ø
Ø
˛
Ø
Ø
(VOICE EDIT)
Ø
˛
Ø
Ø
(Pedal1 – 4)
Ø
˛
Ø
˛
Ø
˛
˛
Ø
(Pedal1 – 4)
Ø
˛
Ø
Ø
(Pedal1 – 4)
Ø
˛
Ø
Ø
(Pedal4, Modulation
Wheel, VOICE EDIT)
Ø
˛
Ø
˛
Ø
˛
˛
1
(01H)
Modulation
0 – 127
(00H...
7FH)
Data
Ø
Ø
5
(05H)
Portamento Time
0 – 127
(00H...
7FH)
Data
Ø
Ø
6
(06H)
Data Entry MSB
0 – 127
(00H...
7FH)
Data
Ø
Ø
7
(07H)
Main Volume
0 – 127
(00H...
7FH)
Data
Ø
Ø
10
(0AH)
Panpot
0 – 127
(00H...
7FH)
L64
Ø
Ø
(20H)
Bank Select LSB
(00H...
7FH)
Data
Ø
Ø
(00H...
0 – 127
7FH)
Data
Ø
Ø
0 – 127
REC
Recorded
Song Midi
from
panel
Ø
(00H)
(40H)
(7EH)
(7FH)
Expression
Panel
(main generation
method)
Ø
0
64
126
127
(0BH)
MIDI Transmission (generated data)
Ø
Bank Select MSB
Ø
(All manually
played parts)
Ø
(All manually
played parts)
Ø
(All manually
played parts)
Ø
(All manually
played parts)
Ø
(All manually
played parts)
Ø
(All manually
played parts)
˛
Ø
(Pedal1 – 4,
Modulation Wheel)
Ø
(Voice)
Ø
(All manually
played parts)
Ø
(All manually
played parts)
Ø
(All manually
played parts)
Ø
(All manually
played parts)
Ø
(All manually
played parts)
Ø
(All manually
played parts)
Ø
(All manually
played parts)
Ø
(All manually
played parts)
Ø
(All manually
played parts)
˛
Ø
˛
˛
Ø
(Pedal4, Modulation
Wheel, VOICE EDIT)
Ø
˛
Ø
˛
˛
Ø
˛
˛
Ø
(All manually
played parts)
Ø
(All manually
played parts)
Ø
(Pedal4, Modulation
Wheel, VOICE EDIT)
Ø
(Pedal4, Modulation
Wheel, VOICE EDIT)
Ø
˛
Ø
Ø
˛
Ø
38
(26H)
Data Entry LSB
0 – 127
(00H...
7FH)
Data
Ø
Ø
64
(40H)
Sustain (Damper)
0 – 127
(00H...
7FH)
Data
Ø
Ø
65
(41H)
Portamento
0 – 127
(00H...
7FH)
0...63, 64...127
(OFF, ON)
Ø
Ø
66
(42H)
Sostenuto
0 – 127
(00H...
7FH)
0...63, 64...127
(OFF, ON)
Ø
Ø
67
(43H)
Soft Pedal
0 – 127
(00H...
7FH)
0...63, 64...127
(OFF, ON)
Ø
Ø
71
(47H)
Harmonic Content
0 – 127
(00H...
7FH)
-64...0...+63
Ø
Ø
72
(48H)
Release Time
0 – 127
(00H...
7FH)
-64...0...+63
Ø
Ø
73
(49H)
Attack Time
0 – 127
(00H...
7FH)
-64...0...+63
Ø
Ø
74
(4AH)
Brightness
0 – 127
(00H...
7FH)
-64...0...+63
Ø
Ø
84
(54H)
Portamento Control
0 – 127
(00H...
Key no. (0 – 127)
7FH)
Ø
Ø
91
(5BH)
Effect1 Depth
(Reverb Send Level)
(00H...
0 – 127
7FH)
Data
Ø
Ø
93
(5DH)
Effect3 Depth
(Chorus Send Level)
0 – 127
(00H...
7FH)
Data
Ø
Ø
94
(00H...
Effect4 Depth
0 – 127
(5EH)
7FH)
(Variation Send Level)
Data
Ø
˛
˛
˛
Ø
˛
˛
Ø
Ø
˛
˛
Ø
˛
˛
Ø
Ø
˛
˛
Ø
˛
˛
Data
Ø
Ø
˛
˛
Ø
˛
˛
Data
Ø
Ø
˛
˛
Ø
˛
˛
Ø
(VOICE EDIT)
Ø
˛
Ø
Ø
(VOICE EDIT)
Ø
˛
Ø
Ø
(Pedal4, Modulation
Wheel)
˛
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
BnH
(n: Channel
Number)
Program
Change
Data
(00H)
32
Mode
Message
Parameter
MIDI Reception (respond/ignore)
Main
Layer
Song
Keyboard
Left
Left Layer
0
11
Control
Change
2nd Data byte
96
(60H)
RPN Increment
–
–
97
(61H)
RPN Decrement
–
–
98
(62H)
NRPN LSB
99
(63H)
NRPN MSB
(00H...
0 – 127
7FH)
(00H...
0 – 127
7FH)
The data byte is
ignored.
The data byte is
ignored.
100
(64H)
RPN LSB
0 – 127
(00H...
7FH)
Data
Ø
Ø
101
(65H)
RPN MSB
0 – 127
(00H...
7FH)
Data
Ø
Ø
Data
˛
˛
0 – 127
(00H...7FH)
Ø
(All manually
played parts)
Ø
(All manually
played parts)
0 – 119
(00H...77H)
(Assignable)
120
(78H)
All Sound Off
0
(00H)
Data
Ø
Ø
121
(79H)
Reset All Controllers
0
(00H)
Data
Ø
˛
123
(7BH)
All Note Off
0
(00H)
Data
Ø
Ø
124
125
(7CH)
(7DH)
Omni Off
Omni On
0
0
Data
Data
Ø
Ø
˛
˛
126
(7EH)
Mono
0 – 16
Data
Ø
˛
˛
˛
Ø
˛
˛
127
(7FH)
(00H...
7FH)
Poly
Voice number
(0 – 127)
0
(00H)
(00H)
(00H...
10H)
(00H)
Data
Ø
˛
˛
Ø
˛
˛
–
–
–
Ø
Ø
˛
˛
Ø
(Voice)
Ø
˛
Ø
pp
˛
Ø
(All manually
played parts)
˛
Ø
(All manually
played parts)
˛
˛
MIDI Data Format
Status byte
MIDI Events
Status
1st Data byte
Data (HEX)
2nd Data byte
Parameter
Data
(HEX)
Parameter
MIDI Reception (respond/ignore)
Main
Layer
Song
Keyboard
Left
Left Layer
MIDI Transmission (generated data)
Panel
(main generation
method)
REC
Recorded
Song Midi
from
panel
Channel After
Touch
DnH
(n: Channel
Number)
vv
(00H...
7FH)
Data
–
–
–
Ø
Ø
Ø
(All manually
played parts)
Ø
(Pedal4, Modulation
Wheel)
Ø
˛
˛
Polyphonic
After Touch
AnH
(n: Channel
Number)
kk
(00H...
7FH)
Key no. (0 – 127)
vv
(00H...
7FH)
Data
Ø
˛
˛
˛
Ø
˛
˛
EnH
(n: Channel
Number)
cc
(00H...
7FH)
(00H...
7FH)
Ø
Ø
(All manually
played parts)
Ø
(Pitch Bend Wheel)
Ø
˛
Ø
˛
Ø
˛
˛
˛
˛
˛
˛
˛
˛
Pitch Bend
Change
Realtime
Message
F8H
FAH
FBH
FCH
FEH
FFH
MIDI Clock
Start
Continue
Stop
Active
Sense
System
Reset
LSB
dd
–
–
–
–
–
–
–
–
–
–
–
–
MSB
–
–
–
–
Ø
˛
˛
˛
˛
–
–
–
–
Ø
Ø
˛
–
–
–
–
˛
˛
˛
MIDI CHANNEL MESSAGE (2)
Parameters controlled by NRPN (Non-Registered Parameter Numbers)
Data Entry
MSB
LSB
MSB
01H
01H
01H
08H mmH
09H mmH
0AH mmH
LSB
–
–
–
01H
20H mmH
–
01H
01H
01H
01H
01H
01H
01H
01H
21H
30H
31H
34H
35H
63H
64H
66H
–
–
–
–
–
–
–
–
mmH
mmH
mmH
mmH
mmH
mmH
mmH
mmH
Parameter
14H
rrH
mmH
–
15H
rrH
mmH
–
16H
rrH
mmH
–
17H
rrH
mmH
–
18H
rrH
mmH
–
19H
rrH
mmH
–
1AH
rrH
mmH
–
1CH
rrH
mmH
–
1DH
rrH
mmH
–
1EH
rrH
mmH
–
1FH
rrH
mmH
–
Vibrato Rate
Vibrato Depth
Vibrato Delay
Low Pass Filter Cutoff
Frequency
Low Pass Filter Resonance
EQ BASS
EQ TREBLE
EQ BASS Frequency
EQ TREBLE Frequency
EG Attack Time
EG Decay Time
EG Release
Drum Low Pass Filter Cutoff
Frequency
Drum Low Pass Filter
Resonance
Data Range
mm: 00H-40H-7FH (-64...0...+63)
mm: 00H-40H-7FH (-64...0...+63)
mm: 00H-40H-7FH (-64...0...+63)
mm: 00H-40H-7FH (-64...0...+63)
mm: 00H-40H-7FH (-64...0...+63)
mm: 00H-40H-7FH (-64...0...+63)
mm: 00H-40H-7FH (-64...0...+63)
mm: 04H-28H (32...2.0k[Hz])
mm: 1CH-3AH (500...16.0k[Hz])
mm: 00H-40H-7FH (-64...0...+63)
mm: 00H-40H-7FH (-64...0...+63)
mm: 00H-40H-7FH (-64...0...+63)
rr: drum instrument note number
mm: 00H-40H-7FH (-64...0...+63)
rr: drum instrument note number
mm: 00H-40H-7FH (-64...0...+63)
rr: drum instrument note number
Drum EG Attack Rate
mm: 00H-40H-7FH (-64...0...+63)
rr: drum instrument note number
Drum EG Decay Rate
mm: 00H-40H-7FH (-64...0...+63)
rr: drum instrument note number
Drum Pitch Coarse
mm: 00H-40H-7FH (-64...0...+63)
rr: drum instrument note number
Drum Pitch Fine
mm: 00H-40H-7FH (-64...0...+63)
rr: drum instrument note number
Drum Level
mm: 00H-7FH (0...127)
rr: drum instrument note number
Drum Pan
mm: 00H, 01H-40H-7FH (RND, L63...C...R63)
rr: drum instrument note number
Drum Reverb Send Level
mm: 00H-7FH (0...127)
rr: drum instrument note number
Drum Chorus Send Level
mm: 00H-7FH (0...127)
rr: drum instrument note number
mm: 00H-7FH (0...127)
Drum Variation Send Level (Variation Connection = SYSTEM)
mm: 00H, 01H-7FH (OFF, ON)
(Variation Connection = INSERTION)
MIDI Reception (respond/ignore)
Main
Layer
Song
Keyboard
Left
Left Layer
Ø
Ø
Ø
Ø
Ø
Ø
˛
˛
˛
MIDI Transmission (generated data)
Panel
(main generation
method)
˛
˛
˛
REC
Recorded
Song Midi
from
panel
Ø
Ø
Ø
˛
˛
˛
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
˛
˛
˛
˛
˛
˛
Ø
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
Appendix
NRPN
NRPN MSB: 14H-1FH (for drums) message is accepted as long as the channel is set with a drum Voice.
Data Entry LSB: Ignored.
Parameters controlled by RPN (Registered Parameter Numbers)
RPN
Data Entry
MSB
LSB
MSB
00H
00H mmH
–
00H
01H mmH
llH
Parameter
LSB
MIDI Reception (respond/ignore)
Main
Layer
Song
Keyboard
Left
Left Layer
MIDI Transmission (generated data)
Panel
(main generation
method)
REC
Recorded
Song Midi
from
panel
Pitch Bend Sensitivity
mm: 00H-18H (0...+24[semitones])
Ø
Ø
Ø
(All manually
played parts)
Ø
(Other Setting)
Ø
˛
Ø
Fine Tune
mm l: 00H 00H
...
mm ll: 40H 00H
...
mm ll: 7FH 7FH
Ø
Ø
Ø
(All manually
played parts)
Ø
(VOICE EDIT)
Ø
˛
Ø
Ø
Ø
˛
Ø
˛
˛
Ø
Ø
˛
Ø
˛
˛
00H
02H mmH
–
Coarse Tune
7FH
7FH
–
Null
–
Data Range
-100 [cent]
0 [cent]
100 [cent]
mm: 28H-40H-58H (-24...0...+24 [semitones])
–
Ø
(All manually
played parts)
Ø
(All manually
played parts)
CP300 Owner’s Manual
127
MIDI Data Format
MIDI PARAMETER CHANGE TABLE
*Not Received when Receive Parameter SysEx is set to off.
*Not transmitted when Transmit Parameter SysEx is set to off.
MIDI Parameter Change table (XG SYSTEM)
Address
(H)
00
00
Size
(H)
Data
(H)
Parameter
00
01
02
03
4
00-0F
00-0F
MASTER TUNE
00-0F
00-0F
04
05
06
7D
7E
7F
1
1
1
1
1
1
00-7F
00-7F
28-58
N
00
00
TOTAL SIZE
Description
-102.4...0...+102.3 [cent]
1st bit 3-0 → bit 15-12
2nd bit 3-0 → bit 11-8
3rd bit 3-0 → bit 7-4
4th bit 3-0 → bit 3-0
0...127
0...127
-24...0...+24 [semitones]
N: Drum setup number
00=XG system ON
00=ON
MASTER VOLUME
MASTER ATTENUATOR
TRANSPOSE
DRUM SETUP RESET
XG SYSTEM ON
ALL PARAMETER RESET
XG Default
(H)
MIDI Reception (respond/ignore)
Main
Layer
Song
Keyboard
Left
Left Layer
*Panel setting
value
Ø
7F
00
40
–
–
–
Ø
˛
Ø
Ø
Ø
Ø
˛
˛
˛
˛
˛
˛
MIDI Transmission (generated data)
Panel
(main generation
method)
˛
˛
˛
˛
˛
˛
REC
Recorded
Song Midi
from
panel
˛
Ø
˛
˛
˛
˛
˛
˛
˛
˛
Ø
˛
Ø
Ø
Ø
Ø
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
Ø
˛
07
MIDI Parameter Change table (SYSTEM INFORMATION)
Address
(H)
01
00
Size
(H)
00
...
0D
0E
0F
E
1
1
Data
(H)
Parameter
20-7F Model Name 1
...
...
20-7F Model Name 14
NOT USED
NOT USED
Description
32...127 (ASCII CHARACTER)
...
32...127 (ASCII CHARACTER)
MIDI Reception (respond/ignore)
Main
Layer
Song
Keyboard
Left
Left Layer
–
–
MIDI Transmission (generated data)
Panel
(main generation
method)
–
˛
REC
Recorded
Song Midi
from
panel
˛
Ø
˛
TOTAL SIZE
10
Transmitted in response to Dump Request. Not received.
MIDI Parameter Change table (EFFECT1)
Address
(H)
Appendix
02
01
Size
(H)
00
01
128
00-7F REVERB TYPE MSB
00-7F REVERB TYPE LSB
Description
Refer to Effect Parameter List
:
1
00-7F REVERB PARAMETER 1
:
03
1
00-7F REVERB PARAMETER 2
:
04
1
00-7F REVERB PARAMETER 3
:
05
1
00-7F REVERB PARAMETER 4
:
06
1
00-7F REVERB PARAMETER 5
:
07
1
00-7F REVERB PARAMETER 6
:
08
1
00-7F REVERB PARAMETER 7
:
09
1
00-7F REVERB PARAMETER 8
:
0A
1
00-7F REVERB PARAMETER 9
:
0B
1
00-7F REVERB PARAMETER 10
0C
0D
1
1
00-7F REVERB RETURN
01-7F REVERB PAN
:
-∞dB...0dB...+6dB (0...64...127)
L63...C...R63
XG Default
(H)
MIDI Reception (respond/ignore)
Main
Layer
Song
Keyboard
Left
Left Layer
01 (=HALL1)
00
Depends on
Reverb type
Depends on
Reverb type
Depends on
Reverb type
Depends on
Reverb type
Depends on
Reverb type
Depends on
Reverb type
Depends on
Reverb type
Depends on
Reverb type
Depends on
Reverb type
Depends on
Reverb type
40
40
Ø
(*Depends on Reverb type)
Ø
(*Depends on Reverb type)
Ø
(*Depends on Reverb type)
Ø
(*Depends on Reverb type)
Ø
(*Depends on Reverb type)
Ø
(*Depends on Reverb type)
Ø
(*Depends on Reverb type)
Ø
(*Depends on Reverb type)
Ø
(*Depends on Reverb type)
Ø
(*Depends on Reverb type)
Ø
Ø
Depends on
Reverb type
Depends on
Reverb type
Depends on
Reverb type
Depends on
Reverb type
Depends on
Reverb type
Depends on
Reverb type
Ø
(*Depends on Reverb type)
Ø
(*Depends on Reverb type)
Ø
(*Depends on Reverb type)
Ø
(*Depends on Reverb type)
Ø
(*Depends on Reverb type)
Ø
(*Depends on Reverb type)
Ø
MIDI Transmission (generated data)
Panel
(main generation
method)
REC
Recorded
Song Midi
from
panel
Ø
(VOICE EDIT)
Ø
˛
Ø
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
˛
Ø
Ø
˛
˛
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
0E
10
1
00-7F REVERB PARAMETER 11
Refer to Effect Parameter List
11
1
00-7F REVERB PARAMETER 12
:
12
1
00-7F REVERB PARAMETER 13
:
13
1
00-7F REVERB PARAMETER 14
:
14
1
00-7F REVERB PARAMETER 15
:
1
00-7F REVERB PARAMETER 16
:
15
TOTAL SIZE
Parameter
02
TOTAL SIZE
02
2
Data
(H)
06
CP300 Owner’s Manual
MIDI Data Format
Address
(H)
01
20
01
00-7F CHORUS PARAMETER 1
:
1
00-7F CHORUS PARAMETER 2
:
24
1
00-7F CHORUS PARAMETER 3
:
25
1
00-7F CHORUS PARAMETER 4
:
26
1
00-7F CHORUS PARAMETER 5
:
27
1
00-7F CHORUS PARAMETER 6
:
28
1
00-7F CHORUS PARAMETER 7
:
29
1
00-7F CHORUS PARAMETER 8
:
2A
1
00-7F CHORUS PARAMETER 9
:
2B
1
00-7F CHORUS PARAMETER 10
:
2C
2D
2E
1
1
1
00-7F CHORUS RETURN
-∞dB...0dB...+6dB (0...64...127)
01-7F CHORUS PAN
L63...C...R63
00-7F SEND CHORUS TO REVERB -∞dB...0dB...+6dB (0...64...127)
30
1
00-7F CHORUS PARAMETER 11
Refer to Effect Parameter List
31
1
00-7F CHORUS PARAMETER 12
:
32
1
00-7F CHORUS PARAMETER 13
:
33
1
00-7F CHORUS PARAMETER 14
:
34
1
00-7F CHORUS PARAMETER 15
:
TOTAL SIZE
Ø
(*Depends on Chorus Type)
Ø
(*Depends on Chorus Type)
Ø
(*Depends on Chorus Type)
Ø
(*Depends on Chorus Type)
Ø
(*Depends on Chorus Type)
Ø
(*Depends on Chorus Type)
Ø
(*Depends on Chorus Type)
Ø
(*Depends on Chorus Type)
Ø
(*Depends on Chorus Type)
Ø
(*Depends on Chorus Type)
Ø
Ø
Ø
Depends on
Chorus Type
Depends on
Chorus Type
Depends on
Chorus Type
Depends on
Chorus Type
Depends on
Chorus Type
Depends on
Chorus Type
Ø
(*Depends on Chorus Type)
Ø
(*Depends on Chorus Type)
Ø
(*Depends on Chorus Type)
Ø
(*Depends on Chorus Type)
Ø
(*Depends on Chorus Type)
Ø
(*Depends on Chorus Type)
Ø
Panel
(main generation
method)
REC
Recorded
Song Midi
from
panel
Ø
(VOICE EDIT)
Ø
˛
Ø
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
˛
˛
Ø
Ø
Ø
˛
˛
˛
˛
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
1
00-7F CHORUS PARAMETER 16
:
˛
Ø
˛
˛
06
Size
(H)
40
2
42
2
44
2
46
2
48
2
4A
2
4C
2
4E
2
50
2
52
2
54
2
56
57
58
59
5A
1
1
1
1
1
Data
(H)
Parameter
00-7F VARIATION TYPE MSB
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
01-7F
00-7F
00-7F
00-01
5B
1
00-7F
5C
5D
5E
5F
60
1
1
1
1
1
00-7F
00-7F
00-7F
00-7F
00-7F
TOTAL SIZE
01
41 (=CHORUS1)
00
Depends on
Chorus Type
Depends on
Chorus Type
Depends on
Chorus Type
Depends on
Chorus Type
Depends on
Chorus Type
Depends on
Chorus Type
Depends on
Chorus Type
Depends on
Chorus Type
Depends on
Chorus Type
Depends on
Chorus Type
40
40
00
MIDI Transmission (generated data)
0F
Address
(H)
02
Refer to Effect Parameter List
:
1
35
01
00-7F CHORUS TYPE MSB
00-7F CHORUS TYPE LSB
MIDI Reception (respond/ignore)
Main
Layer
Song
Keyboard
Left
Left Layer
XG Default
(H)
Description
23
TOTAL SIZE
02
Parameter
22
TOTAL SIZE
02
2
Data
(H)
Description
Refer to Effect Parameter List
VARIATION TYPE LSB
VARIATION PARAMETER 1 MSB
VARIATION PARAMETER 1 LSB
VARIATION PARAMETER 2 MSB
VARIATION PARAMETER 2 LSB
VARIATION PARAMETER 3 MSB
VARIATION PARAMETER 3 LSB
VARIATION PARAMETER 4 MSB
VARIATION PARAMETER 4 LSB
VARIATION PARAMETER 5 MSB
VARIATION PARAMETER 5 LSB
VARIATION PARAMETER 6 MSB
VARIATION PARAMETER 6 LSB
VARIATION PARAMETER 7 MSB
VARIATION PARAMETER 7 LSB
VARIATION PARAMETER 8 MSB
VARIATION PARAMETER 8 LSB
VARIATION PARAMETER 9 MSB
VARIATION PARAMETER 9 LSB
VARIATION PARAMETER 10 MSB
VARIATION PARAMETER 10 LSB
VARIATION RETURN
VARIATION PAN
SEND VARIATION TO REVERB
SEND VARIATION TO CHORUS
VARIATION CONNECTION
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
-∞dB...0dB...+6dB (0...64...127)
L63...C...R63
-∞dB...0dB...+6dB (0...64...127)
-∞dB...0dB...+6dB (0...64...127)
INSERTION, SYSTEM
Reception: Part1...16 (0...15)
VARIATION PART NUMBER
Transmission: Part1...16 (0...15)
OFF (127)
MW VARIATION CONTROL DEPTH
-64...0...+63
BEND VARIATION CONTROL DEPTH
-64...0...+63
CAT VARIATION CONTROL DEPTH
-64...0...+63
AC1 VARIATION CONTROL DEPTH
-64...0...+63
AC2 VARIATION CONTROL DEPTH
-64...0...+63
XG Default
(H)
05 (=DELAY L,
C, R)
00
Depends on
Variation Type
Depends on
Variation Type
Depends on
Variation Type
Depends on
Variation Type
Depends on
Variation Type
Depends on
Variation Type
Depends on
Variation Type
Depends on
Variation Type
Depends on
Variation Type
Depends on
Variation Type
40
40
00
00
00
MIDI Reception
(respond/ignore)
Main
Layer
Song
Keyboard
Left
Left Layer
Panel (main
generation
method)
Ø
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
˛
˛
˛
˛
Ø
Ø
Ø
Ø
Ø
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
Ø
(*Depends on Variation Type)
Ø
(*Depends on Variation Type)
Ø
(*Depends on Variation Type)
Ø
(*Depends on Variation Type)
Ø
(*Depends on Variation Type)
Ø
(*Depends on Variation Type)
Ø
(*Depends on Variation Type)
Ø
(*Depends on Variation Type)
Ø
(*Depends on Variation Type)
Ø
(*Depends on Variation Type)
Ø
Ø
Ø
Ø
Ø
MIDI Transmission
(generated data)
REC
Recorded
Song Midi
from
panel
7F
Ø
˛
Ø
˛
˛
40
40
40
40
40
Ø
Ø
Ø
Ø
Ø
˛
˛
˛
˛
˛
Ø
Ø
Ø
Ø
Ø
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
Depends on
Variation Type
Depends on
Variation Type
Depends on
Variation Type
Depends on
Variation Type
Depends on
Variation Type
Depends on
Variation Type
Ø
(*Depends on Variation Type)
Ø
(*Depends on Variation Type)
Ø
(*Depends on Variation Type)
Ø
(*Depends on Variation Type)
Ø
(*Depends on Variation Type)
Ø
(*Depends on Variation Type)
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
Appendix
02
Size
(H)
21
70
1
00-7F VARIATION PARAMETER 11
Refer to Effect Parameter List
71
1
00-7F VARIATION PARAMETER 12
:
72
1
00-7F VARIATION PARAMETER 13
:
73
1
00-7F VARIATION PARAMETER 14
:
74
1
00-7F VARIATION PARAMETER 15
:
75
1
00-7F VARIATION PARAMETER 16
:
06
CP300 Owner’s Manual
129
MIDI Data Format
MIDI Parameter Change table (MULTI EQ)
Address
(H)
02
40
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
TOTAL SIZE
Size
(H)
Data
(H)
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
00-04
34-4C
04-28
01-78
00-01
34-4C
0E-36
01-78
34-4C
0E-36
01-78
34-4C
0E-36
01-78
34-4C
1C-3A
01-78
00-01
Parameter
EQ TYPE
EQ GAIN 1
EQ FREQUENCY 1
EQ Q 1
EQ SHAPE 1
EQ GAIN 2
EQ FREQUENCY 2
EQ Q 2
NOT USED
EQ GAIN 3
EQ FREQUENCY 3
EQ Q 3
NOT USED
EQ GAIN4
EQ FREQUENCY 4
EQ Q 4
NOT USED
EQ GAIN 5
EQ FREQUENCY 5
EQ Q 5
EQ SHAPE 5
MIDI Reception (respond/ignore)
Main
Layer
Song
Keyboard
Left
Left Layer
Description
flat, jazz, pops, rock, classic
-12...0...+12 [dB]
32...2.0k [Hz]
0.1...12.0
shelving, peaking
-12...0...+12 [dB]
100...10.0k [Hz]
0.1...12.0
-12...0...+12 [dB]
100...10.0k [Hz]
0.1...12.0
*MULTI EQ is
not reset by the
XG System On.
-12...0...+12 [dB]
100...10.0k [Hz]
0.1...12.0
-12...0...+12 [dB]
0.5k...16.0k [Hz]
0.1...12.0
shelving, peaking
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
–
Ø
Ø
Ø
–
Ø
Ø
Ø
–
Ø
Ø
Ø
Ø
MIDI Transmission (generated data)
Panel
(main generation
method)
˛
˛
˛
˛
˛
˛
˛
˛
–
˛
˛
˛
–
˛
˛
˛
–
˛
˛
˛
˛
REC
Recorded
Song Midi
from
panel
˛
˛
˛
˛
˛
˛
˛
˛
–
˛
˛
˛
–
˛
˛
˛
–
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
–
˛
˛
˛
–
˛
˛
˛
–
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
–
˛
˛
˛
–
˛
˛
˛
–
˛
˛
˛
˛
15
MIDI Parameter Change table (EFFECT2)
Address
(H)
03
n
Size
(H)
00
Parameter
00-7F INSERTION EFFECT TYPE MSB
00-7F INSERTION EFFECT TYPE LSB
Description
MIDI Reception (respond/ignore)
Main
Layer
Song
Keyboard
Left
Left Layer
Refer to Effect Parameter List
:
Ø
Appendix
02
1
00-7F INSERTION EFFECT PARAMETER 1
:
03
1
00-7F INSERTION EFFECT PARAMETER 2
:
04
1
00-7F INSERTION EFFECT PARAMETER 3
:
05
1
00-7F INSERTION EFFECT PARAMETER 4
:
06
1
00-7F INSERTION EFFECT PARAMETER 5
:
07
1
00-7F INSERTION EFFECT PARAMETER 6
:
08
1
00-7F INSERTION EFFECT PARAMETER 7
:
09
1
00-7F INSERTION EFFECT PARAMETER 8
:
0A
1
00-7F INSERTION EFFECT PARAMETER 9
:
0B
1
00-7F INSERTION EFFECT PARAMETER 10
:
0C
1
00-7F INSERTION EFFECT PART NUMBER
0D
0E
0F
10
11
1
1
1
1
1
00-7F
00-7F
00-7F
00-7F
00-7F
TOTAL SIZE
MW INSERTION CONTROL DEPTH
BEND INSERTION CONTROL DEPTH
CAT INSERTION CONTROL DEPTH
AC1 INSERTION CONTROL DEPTH
AC2 INSERTION CONTROL DEPTH
Reception: Part1...16 (0...15)
Transmission: Part1...16 (0...15)
OFF (127)
-64...0...+63
-64...0...+63
-64...0...+63
-64...0...+63
-64...0...+63
Ø
(*Depends on Insertion Type)
Ø
(*Depends on Insertion Type)
Ø
(*Depends on Insertion Type)
Ø
(*Depends on Insertion Type)
Ø
(*Depends on Insertion Type)
Ø
(*Depends on Insertion Type)
Ø
(*Depends on Insertion Type)
Ø
(*Depends on Insertion Type)
Ø
(*Depends on Insertion Type)
Ø
(*Depends on Insertion Type)
MIDI Transmission (generated data)
Panel
(main generation
method)
Ø
(VOICE EDIT)
Ø
(VOICE EDIT)
˛
REC
Recorded
Song Midi
from
panel
Ø
˛
Ø
Ø
˛
Ø
Ø
˛
˛
Ø
(VOICE EDIT)
Ø
˛
Ø
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
Ø
(VOICE EDIT)
Ø
˛
Ø
Ø
Ø
(Voice)
Ø
˛
Ø
Ø
Ø
Ø
Ø
Ø
˛
˛
˛
˛
˛
Ø
Ø
Ø
Ø
Ø
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
Ø
(VOICE EDIT)
Ø
˛
Ø
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
12
20
1
00-7F INSERTION EFFECT PARAMETER 11
Refer to Effect Parameter List
21
1
00-7F INSERTION EFFECT PARAMETER 12
:
22
1
00-7F INSERTION EFFECT PARAMETER 13
:
23
1
00-7F INSERTION EFFECT PARAMETER 14
:
24
1
00-7F INSERTION EFFECT PARAMETER 15
:
25
1
00-7F INSERTION EFFECT PARAMETER 16
:
TOTAL SIZE
130
2
Data
(H)
Ø
(*Depends on Insertion Type)
Ø
(*Depends on Insertion Type)
Ø
(*Depends on Insertion Type)
Ø
(*Depends on Insertion Type)
Ø
(*Depends on Insertion Type)
Ø
(*Depends on Insertion Type)
6
30
2
32
2
34
2
36
2
38
2
3A
2
3C
2
3E
2
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
INSERTION EFFECT PARAMETER 1 MSB
INSERTION EFFECT PARAMETER 1 LSB
INSERTION EFFECT PARAMETER 2 MSB
INSERTION EFFECT PARAMETER 2 LSB
INSERTION EFFECT PARAMETER 3 MSB
INSERTION EFFECT PARAMETER 3 LSB
INSERTION EFFECT PARAMETER 4 MSB
INSERTION EFFECT PARAMETER 4 LSB
INSERTION EFFECT PARAMETER 5 MSB
INSERTION EFFECT PARAMETER 5 LSB
INSERTION EFFECT PARAMETER 6 MSB
INSERTION EFFECT PARAMETER 6 LSB
INSERTION EFFECT PARAMETER 7 MSB
INSERTION EFFECT PARAMETER 7 LSB
INSERTION EFFECT PARAMETER 8 MSB
INSERTION EFFECT PARAMETER 8 LSB
CP300 Owner’s Manual
Refer to Effect Parameter List
:
:
:
:
:
:
:
:
:
:
:
:
:
:
:
Ø
(*Depends on Insertion Type)
Ø
(*Depends on Insertion Type)
Ø
(*Depends on Insertion Type)
Ø
(*Depends on Insertion Type)
Ø
(*Depends on Insertion Type)
Ø
(*Depends on Insertion Type)
Ø
(*Depends on Insertion Type)
Ø
(*Depends on Insertion Type)
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
MIDI Data Format
40
2
42
2
TOTAL SIZE
00-7F
00-7F
00-7F
00-7F
INSERTION EFFECT PARAMETER 9 MSB
INSERTION EFFECT PARAMETER 9 LSB
INSERTION EFFECT PARAMETER 10 MSB
INSERTION EFFECT PARAMETER 10 LSB
:
:
:
:
Ø
(*Depends on Insertion Type)
Ø
(*Depends on Insertion Type)
˛
Ø
˛
˛
Ø
(VOICE EDIT)
Ø
˛
Ø
14
The EFFECT2 Parameter cannot be reset to its factory setting with XG SYSTEM ON.
The second byte of the address is considered as an Insertion effect number.
n: insertion effect number (n = 0 – 2)
For effect types that do not require MSB, the Parameters for Address 02 – 0B will be received and the Parameters for Address 30 – 42 will not be received.
For effect types that require MSB, the Parameters for Address 30 – 42 will be received and the Parameters for Address 02 – 0B will not be received.
When Bulk Dumps that include Effect Type data are transmitted, the Parameters for Address 02-0B will always be transmitted. But, effects that require MSB, when the bulk dump is received the
Parameters for Address 02 – 0B will not be received.
MIDI Parameter Change table (MULTI PART)
08
nn
Size
(H)
Data
(H)
Parameter
Description
XG Default
(H)
MIDI Reception (respond/ignore)
Main
Layer
Song
Keyboard
Left
Left Layer
MIDI Transmission (generated data)
Panel
(main generation
method)
REC
Recorded
Song Midi
from
panel
00
1
00-20 NOT USED
01
1
00-7F BANK SELECT MSB
0...127
02
03
1
1
0...127
1...128
04
1
1...16, OFF
Part No.
Ø
˛
˛
˛
Ø
˛
˛
05
1
00-7F
00-7F
00-0F,
7F
00-01
part10=7F,
other parts=00
00
00
MONO, POLY
SINGLE, MULTI, INST
(for Drum)
NORMAL, DRUM,
DRUMS1...2
-24...0...+24 [semitones]
-12.8...0...+12.7 [Hz]
1st bit3-0 → bit7-4
2nd bit3-0 → bit3-0
0...127
01
Ø
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
Ø
˛
Ø
Ø
˛
˛
BANK SELECT LSB
PROGRAM NUMBER
Rcv CHANNEL
MONO/POLY MODE
SAME NOTE NUMBER KEY ON
00-02
ASSIGN
01
˛
˛
˛
˛
˛
˛
Ø
Ø
˛
˛
Ø
˛
˛
Ø
Ø
Ø
Ø
˛
˛
˛
˛
Ø
Ø
˛
˛
˛
˛
Ø
˛
˛
Ø
˛
˛
Ø
Ø
˛
06
1
07
1
00-03 PART MODE
08
1
28-58 NOTE SHIFT
09
0A
2
00-0F
DETUNE
00-0F
0B
1
00-7F VOLUME
0C
1
00-7F VELOCITY SENSE DEPTH
0...127
40
Ø
Ø
˛
0D
1
00-7F VELOCITY SENSE OFFSET
0...127
40
Ø
Ø
˛
0E
0F
10
11
12
13
14
15
16
17
18
19
1A
1B
1C
1D
1E
1F
20
21
22
23
24
25
26
27
28
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
00-7F
28-58
00-7F
00-7F
00-7F
00-7F
00-7F
28-58
00-7F
00-7F
00-7F
00-7F
00-7F
RND, L63...C...R63
C-2...G8
C-2...G8
0...127
0...127
0...127
0...127
-64...0...+63
-64...0...+63
-64...0...+63
-64...0...+63
-64...0...+63
-64...0...+63
-64...0...+63
-64...0...+63
-24...0...+24 [semitones]
-9600...0...+9450 [cent]
-100...0...+100 [%]
0...127
0...127
0...127
-24...0...+24 [semitones]
-9600...0...+9450 [cent]
-100...0...+100 [%]
0...127
0...127
0...127
40
00
7F
7F
00
28
00
40
40
40
40
40
40
40
40
40
40
40
0A
00
00
42
40
40
00
00
00
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
Description
XG Default
(H)
TOTAL SIZE
PAN
NOTE LIMIT LOW
NOTE LIMIT HIGH
DRY LEVEL
CHORUS SEND
REVERB SEND
VARIATION SEND
VIBRATO RATE
VIBRATO DEPTH
VIBRATO DELAY
FILTER CUTOFF FREQUENCY
FILTER RESONANCE
EG ATTACK TIME
EG DECAY TIME
EG RELEASE TIME
MW PITCH CONTROL
MW LOW PASS FILTER CONTROL
MW AMPLITUDE CONTROL
MW LFO PMOD DEPTH
MW LFO FMOD DEPTH
MW LFO AMOD DEPTH
BEND PITCH CONTROL
BEND LOW PASS FILTER CONTROL
BEND AMPLITUDE CONTROL
BEND LFO PMOD DEPTH
BEND LFO FMOD DEPTH
BEND LFO AMOD DEPTH
part10=02,
other parts=00
40
Ø
(Drum Voice)
˛
˛
08 00
Ø
Ø
˛
˛
Ø
˛
˛
64
Ø
Ø
˛
˛
Ø
(VOICE EDIT)
Ø
(VOICE EDIT)
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
Ø
˛
˛
Ø
˛
Ø
Ø
˛
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
Appendix
Address
(H)
29
Address
(H)
Size
(H)
Data
(H)
30
31
32
33
34
35
36
1
1
1
1
1
1
1
00-01
00-01
00-01
00-01
00-01
00-01
00-01
37
1
00-01 Rcv NRPN
OFF, ON
38
39
3A
3B
3C
3D
3E
3F
40
1
1
1
1
1
1
1
1
1
00-01
00-01
00-01
00-01
00-01
00-01
00-01
00-01
00-01
41
1
00-7F SCALE TUNING C
Parameter
Rcv PITCH BEND
Rcv CH AFTER TOUCH (CAT)
Rcv PROGRAM CHANGE
Rcv CONTROL CHANGE
Rcv POLY AFTER TOUCH (PAT)
Rcv NOTE MESSAGE
Rcv RPN
Rcv MODULATION
Rcv VOLUME
Rcv PAN
Rcv EXPRESSION
Rcv HOLD1
Rcv PORTAMENTO
Rcv SOSTENUTO
Rcv SOFT PEDAL
Rcv BANK SELECT
OFF, ON
OFF, ON
OFF, ON
OFF, ON
OFF, ON
OFF, ON
OFF, ON
MIDI Reception (respond/ignore)
Main
Layer
Song
Keyboard
Left
Left Layer
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
MIDI Transmission (generated data)
Panel
(main generation
method)
˛
˛
˛
˛
˛
˛
˛
REC
Recorded
Song Midi
from
panel
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
˛
˛
˛
Ø
˛
˛
OFF, ON
OFF, ON
OFF, ON
OFF, ON
OFF, ON
OFF, ON
OFF, ON
OFF, ON
OFF, ON
01
01
01
01
01
01
01
XGmode=01,
GMmode=00
01
01
01
01
01
01
01
01
01
Ø
Ø
Ø
Ø
Ø
Ø
Ø
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
-63...0...+63 [cent]
40
Ø
Ø
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
Ø
(Other Setting)
Ø
˛
Ø
CP300 Owner’s Manual
131
MIDI Data Format
Address
(H)
Size
(H)
Parameter
Description
XG Default
(H)
1
00-7F SCALE TUNING C#
-63...0...+63 [cent]
40
Ø
Ø
˛
43
1
00-7F SCALE TUNING D
-63...0...+63 [cent]
40
Ø
Ø
˛
44
1
00-7F SCALE TUNING D#
-63...0...+63 [cent]
40
Ø
Ø
˛
45
1
00-7F SCALE TUNING E
-63...0...+63 [cent]
40
Ø
Ø
˛
46
1
00-7F SCALE TUNING F
-63...0...+63 [cent]
40
Ø
Ø
˛
47
1
00-7F SCALE TUNING F#
-63...0...+63 [cent]
40
Ø
Ø
˛
48
1
00-7F SCALE TUNING G
-63...0...+63 [cent]
40
Ø
Ø
˛
49
1
00-7F SCALE TUNING G#
-63...0...+63 [cent]
40
Ø
Ø
˛
Appendix
4A
1
00-7F SCALE TUNING A
-63...0...+63 [cent]
40
Ø
Ø
˛
4B
1
00-7F SCALE TUNING A#
-63...0...+63 [cent]
40
Ø
Ø
˛
4C
1
00-7F SCALE TUNING B
4D
4E
4F
50
51
52
53
54
55
56
57
58
59
5A
5B
5C
5D
5E
5F
60
61
62
63
64
65
66
67
68
69
6A
6B
6C
6D
6E
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
28-58
00-7F
00-7F
00-7F
00-7F
00-7F
28-58
00-7F
00-7F
00-7F
00-7F
00-7F
00-5F
28-58
00-7F
00-7F
00-7F
00-7F
00-7F
00-5F
28-58
00-7F
00-7F
00-7F
00-7F
00-7F
00-01
00-7F
00-7F
00-7F
00-7F
00-7F
01-7F
01-7F
CAT PITCH CONTROL
CAT LOW PASS FILTER CONTROL
CAT AMPLITUDE CONTROL
CAT LFO PMOD DEPTH
CAT LFO FMOD DEPTH
CAT LFO AMOD DEPTH
PAT PITCH CONTROL
PAT LOW PASS FILTER CONTROL
PAT AMPLITUDE CONTROL
PAT LFO PMOD DEPTH
PAT LFO FMOD DEPTH
PAT LFO AMOD DEPTH
AC1 CONTROLLER NUMBER
AC1 PITCH CONTROL
AC1 LOW PASS FILTER CONTROL
AC1 AMPLITUDE CONTROL
AC1 LFO PMOD DEPTH
AC1 LFO FMOD DEPTH
AC1 LFO AMOD DEPTH
AC2 CONTROLLER NUMBER
AC2 PITCH CONTROL
AC2 LOW PASS FILTER CONTROL
AC2 AMPLITUDE CONTROL
AC2 LFO PMOD DEPTH
AC2 LFO FMOD DEPTH
AC2 LFO AMOD DEPTH
PORTAMENTO SWITCH
PORTAMENTO TIME
PITCH EG INITIAL LEVEL
PITCH EG ATTACK TIME
PITCH EG RELEASE LEVEL
PITCH EG RELEASE TIME
VELOCITY LIMIT LOW
VELOCITY LIMIT HIGH
-63...0...+63 [cent]
40
Ø
Ø
˛
-24...0...+24 [semitones]
-9600...0...+9450 [cent]
-100...0...+100 [%]
0...127
0...127
0...127
-24...0...+24 [semitones]
-9600...0...+9450 [cent]
-100...0...+100 [%]
0...127
0...127
0...127
0...95
-24...0...+24 [semitones]
-9600...0...+9450 [cent]
-100...0...+100 [%]
0...127
0...127
0...127
0...95
-24...0...+24 [semitones]
-9600...0...+9450 [cent]
-100...0...+100 [%]
0...127
0...127
0...127
OFF, ON
0...127
-64...0...+63
-64...0...+63
-64...0...+63
-64...0...+63
1...127
1...127
40
40
40
00
00
00
40
40
40
00
00
00
10
40
40
40
00
00
00
11
40
40
40
00
00
00
00
00
40
40
40
40
01
7F
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
Ø
Ø
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
–
–
–
–
–
–
–
–
MIDI Transmission (generated data)
Panel
(main generation
method)
Ø
(Other Setting)
Ø
(Other Setting)
Ø
(Other Setting)
Ø
(Other Setting)
Ø
(Other Setting)
Ø
(Other Setting)
Ø
(Other Setting)
Ø
(Other Setting)
Ø
(Other Setting)
Ø
(Other Setting)
Ø
(Other Setting)
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
REC
Recorded
Song Midi
from
panel
Ø
˛
Ø
Ø
˛
Ø
Ø
˛
Ø
Ø
˛
Ø
Ø
˛
Ø
Ø
˛
Ø
Ø
˛
Ø
Ø
˛
Ø
Ø
˛
Ø
Ø
˛
Ø
Ø
˛
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
–
–
–
–
–
–
Ø
˛
Ø
Ø
˛
Ø
–
–
–
–
–
–
Ø
˛
Ø
Ø
˛
Ø
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
3F
70
71
1
1
72
1
00-7F EQ BASS GAIN
-12dB...+12dB
40
Ø
Ø
˛
1
00-7F EQ TREBLE GAIN
-12dB...+12dB
40
Ø
Ø
˛
–
–
–
–
–
–
–
–
32...2.0k[Hz]
0C
Ø
Ø
˛
500...16.0k[Hz]
36
Ø
Ø
˛
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
73
TOTAL SIZE
NOT USED
NOT USED
–
–
Ø
(VOICE EDIT)
Ø
(VOICE EDIT)
04
74
75
1
1
NOT USED
NOT USED
76
1
04-28 EQ BASS FREQUENCY
77
1
1C-3A EQ TREBLE FREQUENCY
78
79
7A
7B
7C
7D
7E
7F
1
1
1
1
1
1
1
1
NOT USED
NOT USED
NOT USED
NOT USED
NOT USED
NOT USED
NOT USED
NOT USED
0C
nn = PART NUMBER
If there is a Drum Voice assigned to the part, the following parameters are ineffective.
• BANK SELECT LSB
• MONO/POLY MODE
• SCALE TUNING
• PORTAMENTO
• PITCH EG
• FILTER MODULATION DEPTH (FMOD DEPTH)
• AMPLITUDE MODULATION DEPTH (AMOD DEPTH)
132
MIDI Reception (respond/ignore)
Main
Layer
Song
Keyboard
Left
Left Layer
42
TOTAL SIZE
TOTAL SIZE
Data
(H)
CP300 Owner’s Manual
–
–
Ø
(VOICE EDIT)
Ø
(VOICE EDIT)
–
–
–
–
–
–
–
–
MIDI Data Format
MIDI Parameter Change table (DRUM SETUP)
Address
(H)
rr
00
01
1
1
Data
(H)
Parameter
00-7F PITCH COARSE
00-7F PITCH FINE
02
1
00-7F LEVEL
03
1
00-7F ALTERNATE GROUP
-64...0...+63
-64...0...+63 [cent]
40
40
Depends on the
note
Depends on the
note
Depends on the
note
Depends on the
note
Depends on the
note
7F
00
Depends on the
note
01
0...127
04
1
00-7F PAN
05
1
00-7F REVERB SEND
OFF, 1...127
RND, L63...C...R63
06
1
00-7F CHORUS SEND
07
08
1
1
00-7F VARIATION SEND
00-01 KEY ASSIGN
0...127
0...127
0...127
SINGLE, MULTI
09
1
00-01 Rcv NOTE OFF
OFF, ON
0A
1
OFF, ON
0B
1
0C
0D
0E
0F
1
1
1
1
00-01 Rcv NOTE ON
LOW PASS FILTER CUTOFF
00-7F
FREQUENCY
00-7F LOW PASS FILTER RESONANCE
00-7F EG ATTACK RATE
00-7F EG DECAY1 RATE
00-7F EG DECAY2 RATE
TOTAL SIZE
XG Default
(H)
Description
MIDI Reception (respond/ignore)
Main
Layer
Song
Keyboard
Left
Left Layer
Ø
Ø
˛
˛
MIDI Transmission (generated data)
Panel
(main generation
method)
˛
˛
REC
Recorded
Song Midi
from
panel
˛
˛
Ø
Ø
˛
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
Ø
Ø
˛
˛
˛
˛
˛
˛
Ø
Ø
˛
˛
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
Ø
˛
˛
˛
Ø
˛
˛
-64...0...+63
40
Ø
˛
˛
˛
Ø
˛
˛
-64...0...+63
-64...0...+63
-64...0...+63
-64...0...+63
40
40
40
40
Ø
Ø
Ø
Ø
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
˛
Ø
Ø
Ø
Ø
˛
˛
˛
˛
˛
˛
˛
˛
-12...+12 [dB]
-12...+12 [dB]
40
40
–
–
0C
36
–
–
–
–
–
–
–
–
Ø
Ø
–
–
Ø
Ø
–
–
–
–
–
–
–
–
˛
˛
–
–
˛
˛
–
–
–
–
–
–
–
–
˛
˛
–
–
˛
˛
–
–
–
–
–
–
–
–
˛
˛
–
–
˛
˛
–
–
–
–
–
–
–
–
Ø
Ø
–
–
Ø
Ø
–
–
–
–
–
–
–
–
˛
˛
–
–
˛
˛
–
–
–
–
–
–
–
–
˛
˛
–
–
˛
˛
–
–
–
–
–
–
–
–
10
20
21
22
23
24
25
26
27
28
29
2A
2B
2C
2D
1
1
1
1
1
1
1
1
1
1
1
1
1
1
TOTAL SIZE
00-7F EQ BASS GAIN
00-7F EQ TREBLE GAIN
NOT USED
NOT USED
04-28 EQ BASS FREQUENCY
1C-3A EQ TREBLE FREQUENCY
NOT USED
NOT USED
NOT USED
NOT USED
NOT USED
NOT USED
NOT USED
NOT USED
32...2.0k [Hz]
500...16.0k [Hz]
Appendix
3n
Size
(H)
0E
n: Drum Setup Number (0-1)
rr: note number (0D-5B)
In the following cases, the PF-500 will initialize all Drum Setups.
XG SYSTEM ON received
GM SYSTEM ON received
DRUM SETUP RESET received (only when in XG mode)
When a part to which a Drum Setup is assigned receives a program change, the assigned Drum Setup will be initialized.
If the same Drum Setup is assigned to two or more parts, changes in Drum Setup parameters (including program changes) will apply to all parts to which it is assigned.
System Exclusive Messages (1)
*Not Received when Receive Parameter SysEx is set to off.
*Not transmitted when Transmit Parameter SysEx is set to off.
System Exclusive Messages (Universal Realtime messages)
MIDI Event
Data Format
F0
Master
Volume
7F XN 04
11110000
01111111
0xxxnnnn
00000100
00000001
0sssssss
0ttttttt
11110111
Ø: Available
MIDI Reception
(effective or not for each part)
Main
Layer
Song
Keyboard
Left
Left Layer
MIDI Reception
(affecting the
panel)
MIDI Transmission
(generated data)
REC
Panel (main
generation
method)
Song
Midi
Recorded
from
panel
˛
˛
(Output as XG
Master Volume)
˛
˛
01 SS TT F7
F0 = Exclusive status
7F = Universal Real Time
XN = When N is received N = 0-F, whichever is
04
01
SS
TT
F7
received. X = ignored
= Sub-ID #1 = Device Control Message
Ø
˛
˛
˛
= Sub-ID #2 = Master Volume
= Volume LSB
= Volume MSB
= End of Exclusive
System Exclusive Messages (Universal Non Realtime messages)
MIDI Event
Data Format
F0
GM1
System On
7E XN 09
11110000
01111110
0xxxnnnn
00001001
00000001
11110111
01 F7
F0 = Exclusive status
7E = Universal Non-Real Time
XN = When N is received N = 0-F, whichever is
received. X = ignored
09 = Sub-ID #1 = General MIDI Message
MIDI Reception
(effective or not for each part)
Main
Layer
Song
Keyboard
Left
Left Layer
Ø
˛
˛
MIDI Reception
(affecting the
panel)
Ø
(VOICE EDIT
Reverb Type
Chorus Type)
MIDI Transmission
(generated data)
Panel (main
generation
method)
Song
˛
Ø
REC
Recorded
Midi
from
panel
˛
Ø
01 = Sub-ID #2 = General MIDI On
F7 = End of Exclusive
CP300 Owner’s Manual
133
MIDI Data Format
System Exclusive Messages (2)
*Not received when the Receive Parameter SysEx is set to off.
*Not transmitted when the Transmit Parameter SysEx is set to off.
System Exclusive Messages (XG)
MIDI Event
Data Format
F0
XG Parameter
Change
F0
XG Bulk Dump
F0
Appendix
XG Parameter
Request
F0
XG Dump
Request
134
43
1n
4C
11110000
01000011
0001nnnn
hh
F0
43
1n
01001100
0hhhhhhh
0mmmmmmm
0lllllll
0ddddddd
:
11110111
43
0n
4C
11110000
01000011
0000nnnn
4C
hh
mm
ll
dd
01001100
0aaaaaaa
0bbbbbbb
0hhhhhhh
0mmmmmmm
0lllllll
0ddddddd
:
0ddddddd
0ccccccc
11110111
43
3n
4C
11110000
01000011
0011nnnn
4C
aa
bb
hh
mm
ll
dd
01001100
0hhhhhhh
0mmmmmmm
0lllllll
11110111
43
2n
4C
11110000
01000011
0010nnnn
4C
hh
mm
ll
F7
hh
F0
43
2n
01001100
0hhhhhhh
0mmmmmmm
0lllllll
11110111
4C
hh
mm
ll
F7
CP300 Owner’s Manual
mm
ll
dd
...
MIDI Reception
(effective or not for each part)
Main
Layer
Song
Keyboard
Left
Left Layer
MIDI Reception
(affecting the
panel)
MIDI Transmission
(generated data)
Ø
*Refer to Parameter Change
Table
–
Ø
*Refer to Parameter
Change Table
˛
Ø
*Refer to Parameter Change
Table
–
Ø
*Refer to Parameter
Change Table
˛
Ø
*Refer to Parameter Change
Table
–
˛
Ø
*Refer to Parameter Change
Table
–
˛
Panel (main
generation
method)
Song
Midi
F7
= Exclusive status
= YAMAHA ID
= Device Number n = always 0 (when transmit),
n = 0-F (when receive)
= Model ID
= Address High
= Address Mid
= Address Low
= Data
:
F7
aa
F0
43
0n
= End of Exclusive
bb
hh
mm
ll
dd
...
dd
cc
F7
= Exclusive status
= YAMAHA ID
= Device Number n = always 0 (when transmit),
n = 0-F (when receive)
= Model ID
= Byte Count MSB
= Byte Count LSB
= Address High
= Address Mid
= Address Low
= Data
:
dd
cc
F7
hh
F0
43
3n
= Data
= Checksum
= End of Exclusive
mm
ll
F7
= Exclusive status
= YAMAHA ID
= Device Number n = always 0 (when transmit),
n = 0-F (when receive)
= Model ID
= Address High
= Address Mid
= Address Low
= End of Exclusive
mm
ll
dd
F7
= Exclusive status
= YAMAHA ID
= Device Number n = always 0 (when transmit),
n = 0-F (when receive)
= Model ID
= Address High
= Address Mid
= Address Low
= End of Exclusive
MIDI Data Format
System Exclusive Message (Preset Voice)
MIDI Event
MIDI Reception
(effective or not for each part)
Main
Layer
Song
Keyboard
Left
Left Layer
Data Format
String
Resonance
Depth
F0
Sustain
Sampling
Depth
F0
Key-off
Sampling
Depth
F0
Soft Pedal
Depth
43
73
01
11110000
01000011
01110011
00000001
01010000
00010001
0000nnnn
00000010
0ddddddd
11110111
43
73
01
11110000
01000011
01110011
00000001
01010000
00010001
0000nnnn
00000011
0ddddddd
11110111
43
73
01
11110000
01000011
01110011
00000001
01010000
00010001
0000nnnn
00000100
0ddddddd
11110111
43
73
01
11110000
01000011
01110011
00000001
01010000
00010001
0000nnnn
00000101
0ddddddd
11110111
50
F0
43
73
01
50
11
0n
02
dd
F7
50
F0
43
73
01
50
11
0n
03
dd
F7
50
F0
43
73
01
50
11
0n
04
dd
F7
50
F0
43
73
01
50
11
0n
05
dd
F7
11
0n
02
dd
MIDI Transmission
(generated data)
Panel (main
generation
method)
Song
Midi
F7
= Exclusive status
= YAMAHA ID
= Clavinova ID
= Model ID (Clavinova common ID)
= Sub ID
Ø
Ø
˛
Ø
(Other Setting)
Ø
(Other Setting)
Ø
˛
Ø
Ø
˛
Ø
(Other Setting)
Ø
(Other Setting)
Ø
˛
Ø
Ø
˛
Ø
(Other Setting)
Ø
(Other Setting)
Ø
˛
Ø
Ø
˛
Ø
(Other Setting)
Ø
(Other Setting)
Ø
˛
= Sub ID
= Channel (00 – 0F)
= Sub ID (String Resonance Depth)
= Depth (00 – 48)
= End of Exclusive
11
0n
03
dd
F7
= Exclusive status
= YAMAHA ID
= Clavinova ID
= Model ID (Clavinova common ID)
= Sub ID
= Sub ID
= Channel (00 – 0F)
= Sub ID (Sustain Sampling Depth)
= Depth (00 – 48)
= End of Exclusive
11
0n
04
dd
F7
= Exclusive status
= YAMAHA ID
= Clavinova ID
= Model ID (Clavinova common ID)
= Sub ID
= Sub ID
= Channel (00 – 0F)
= Sub ID (Key-off Sampling Depth)
= Depth (00 – 50)
= End of Exclusive
11
0n
05
dd
F7
= Exclusive status
Appendix
F0
MIDI Reception
(affecting the
panel)
= YAMAHA ID
= Clavinova ID
= Model ID (Clavinova common ID)
= Sub ID
= Sub ID
= Channel (00 – 0F)
= Sub ID (Soft Pedal Depth)
= Depth (00 – 7F)
= End of Exclusive
*For each Depth value, the reset value is 40H = Voice parameter.
System Exclusive Message (Other)
MIDI Event
Data Format
F0
MIDI Master
Tuning
43
1n
27
11110000
01000011
0001nnnn
00100111
00110000
00000000
00000000
0000mmmm
0000llll
0ccccccc
11110111
30
F0
43
1n
27
30
00
00
0m
0l
cc
F7
00
00
Om
Ol
cc
MIDI Reception
(effective or not for each part)
Main
Layer
Song
Keyboard
Left
Left Layer
MIDI Reception
(affecting the
panel)
Ø
Ø
(Other Setting)
MIDI Transmission
(generated data)
Panel (main
generation
method)
Song
Midi
˛
Ø
˛
F7
= Exclusive status
= YAMAHA ID
n = always 0 (when transmit), n = 0-F (when receive)
= Model ID of TG100
= Address High
= Address Mid
= Address Low
= Master Tune MSB
= Master Tune LSB
= irrelevant
= End of Exclusive
CP300 Owner’s Manual
135
MIDI Data Format
System Exclusive Message (Data Bulk )
MIDI Event
Data Bulk
Dump
Data Format
MIDI Transmission
(generated data)
MIDI Reception
(affecting the panel)
Panel (main
generation
method)
Song
Midi
˛
Ø
(Bulk Request)
Ø
(Bulk Request)
Ø
(Bulk Request)
F0 43 0n xx yy zz aa bb cc dd hh mm ll dd ... dd sum F7
11110000
F0 = Exclusive status
01000011
43 = YAMAHA ID
0000nnnn
0n = Device Number n = always 0
0xxxxxxx
7F = Model ID High
0zzzzzzz
04 = Model ID Low
0aaaaaaa
aa = Byte Count MSB
0bbbbbbb
bb = Byte Count LSB
0ccccccc
cc = The number of available MSB
0ddddddd
dd = The number of available LSB
0hhhhhhh
hh = Address High
0mmmmmmm
mm = Address Mid
0lllllll
ll = Address Low
0ddddddd
dd = Data
:
:
0ddddddd
dd = Data
0ccccccc
cc = Checksum
Function
Address High
Address Mid
Address Low
Bulk Header
10
00
00
–
–
–
Current
(End)
Performance
20
00
7F
00
00
7F
00
00
7F
00
00
7F
00
:
7F
00
:
7F
00
–
Ø
Ø
–
–
–
–
–
–
–
–
–
–
–
–
–
–
30
(End)
Voice Setting
40
(End)
Bulk Footer
11
Appendix
F0 43 2n xx yy zz hh mm
11110000
F0
01000011
43
0000nnnn
2n
0xxxxxxx
7F
0zzzzzzz
04
0hhhhhhh
hh
Data Bulk
Dump Request
0mmmmmmm
mm
0lllllll
ll
Function
Current,
Performance,
Voice Setting
136
MIDI Reception
(effective or not for each part)
Main
Layer
Song
Keyboard
Left
Left Layer
CP300 Owner’s Manual
–
Ø
(Bulk)
Ø
Ø
(Other than the Data Bulk) (Bulk Current)
Ø
Ø
(Bulk
(Performance)
Performance)
Ø
–
(Bulk Voice)
(Voice Setting)
˛
˛
˛
Ø
(Bulk Request)
Ø
(Bulk)
˛
Ø
(Bulk Request)
˛
˛
˛
ll F7
= Exclusive status
= YAMAHA ID
= Device Number n = always 0
= Model ID High
= Model ID Low
= Address High
= Address Mid
= Address Low
Address High
Address Mid
Address Low
00
00
00
MIDI Implementation Chart
YAMAHA
[ Stage Piano ]
CP300 MIDI Implementation Chart
Transmitted
Recognized
Basic
Channel
Default
Changed
1 - 16
1 - 16
1 - 16
1 - 16
Mode
Default
Messages
Altered
3
3
˛
**************
˛
˛
0 - 127
**************
0 - 127
0 - 127
Note
Number : True voice
Velocity
Note ON Ø 9nH,v=1-127
Note OFF ˛ 9nH,v=0
Ø
˛
After
Touch
Key's
Ch's
˛
˛
Ø
Ø
Ø
Ø
Ø
Ø
˛
Ø
Ø
Ø
˛
Ø
˛
˛
Ø
˛
˛
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
Ø
˛
Pitch Bend
0,32
1
5
7,10,11
6,38
64,66,67
65
71,74
72,73
84,94
91,93
96-97
98-99
100-101
1-119
Control
Change
Prog
Change
Ø
0 - 127
**************
Ø
Ø
Ø
: Song Pos. ˛
: Song Sel. ˛
: Tune
˛
˛
˛
˛
:
True #
System Exclusive
Common
(Assignable)
System
: Clock
Real Time : Commands
Ø
Ø
˛
Ø
:
:
:
Mes- :
sages:
:
˛
˛
˛
˛
Ø
˛
Ø
Ø
˛
Ø
Ø
˛
Aux
All Sound Off
Reset All Cntrls
Local ON/OFF
All Notes OFF
Active Sense
Reset
Remarks
9nH,v=1-127
0 - 24 semi
Bank Select
Modulation
Portamento Time
Data Entry
Portamento
Sound Controller
Sound Controller
Appendix
Function...
Date :1-NOV-2005
Version : 1.0
RPN Inc,Dec
NRPN LSB,MSB
RPN LSB,MSB
*1
0 - 127
(120,126,127)
(121)
(122)
(123-125)
Note : *1= Transmission only
Mode 1 : OMNI ON , POLY
Mode 3 : OMNI OFF, POLY
Mode 2 : OMNI ON ,MONO
Mode 4 : OMNI OFF,MONO
Ø
˛
: Yes
: No
CP300 Owner’s Manual
137
Specifications
Item
CP300
Appendix
Keyboard
GH keyboard 88 keys (A-1 – C7)
Sound Source
AWM Dynamic Stereo Sampling
Polyphony (max.)
128
Voice Selection
Panel preset for manual Performance: 50 Voices
XG Voices: 480 Voices + 12 Drum kits
Performance
64 Performamces x 56 files (max.)
Effect
Reverb*1, Chorus*1, Master Equalizer, Variation effect*1, Insertion effect*1 x 3
Controller
Master Volume Dial, Pitch Bend Wheel, Modulation Wheel, Master Equalizer Slider, Zone Control
Slider, Song Volume Slider
Display
24 charaters x 2 lines, LCD with back-light
Recording/Playback
16-track recording/playback, Tempo adjustment, max. capacity: 1.4 MB, 140,000 notes
Jacks/Connectors
MIDI (IN/OUT/THRU), PHONES, INPUT (L/MONO, R), OUTPUT (L/MONO, R), OUTPUT (L/R),
ASSIGNABLE FOOT PEDAL (SUSTAIN/SOSTENUTO/SOFT/AUX), USB TO HOST, AC INLET
Main Amplifiers
30 W x 2
Speakers
13 cm x 2
Dimensions (W x D x H)
1391 x 461 x 166mm (54-3/4" x 18-1/8" x 6-1/2")
Weight
32.5 kg (71 lbs., 10 oz)
Accessories
AC Power Cord, Foot Pedal FC3, Owner’s Manual
*1: Refer to the Effect type on page 114.
Specifications and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right to change or modify
products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale,
please check with your Yamaha dealer.
138
CP300 Owner’s Manual
Index
Numerics
[1] – [16] buttons .......................................................... 73
A
A [–][+] buttons ............................................................ 15
[AC INLET] jack ............................................................ 11
Application Index .......................................................... 10
[ASSIGNABLE FOOT PEDAL] jacks ............................. 11
[AUX] jack ..................................................................... 33
AUX pedal .................................................................... 33
Factory Setting List ..................................................... 101
Factory-programmed settings ...................................... 16
Fast Forward ................................................................. 50
Fast Rewind .................................................................. 50
File ................................................................................ 17
G
GM System Level 1 ..................................................... 100
H
Headphones ................................................................. 12
B
B [– (NO)][+(YES)] buttons ........................................... 15
Bar ................................................................................ 42
Basic operation ............................................................. 15
Bulk Dump .................................................................... 66
I
INPUT [L/MONO][R] jack .............................................. 89
Insertion effect .............................................................. 35
K
C [–][+] button .............................................................. 15
Character Code ............................................................ 84
Chorus .......................................................................... 35
[CHORUS] button ......................................................... 35
Click .............................................................................. 38
[CLICK] button .............................................................. 38
Connections
computer ................................................................ 92
external audio equipment ...................................... 88
external instrument ................................................ 89
external MIDI keyboard ......................................... 90
[CONTRAST] knob ....................................................... 13
Current memory ............................................................ 82
D
D [–][+] buttons ............................................................ 15
Delete
Performance file ..................................................... 80
Song file ................................................................. 83
Demo Songs ................................................................. 23
Display
adjust the brightness ............................................. 13
settings .................................................................. 15
Dual .............................................................................. 29
E
Effect Data Assign Table ............................................ 123
Effect Parameter List .................................................. 115
Effect Type List ........................................................... 114
Equalizer (EQ) .............................................................. 36
[EXIT] button ................................................................. 15
F
Factory Set .............................................................. 16, 71
Keyboard part combinations ........................................ 27
L
Layer part ...................................................................... 27
Left Layer part ............................................................... 27
Left part ......................................................................... 27
List
Effect Parameter List ............................................ 115
Effect Type List .................................................... 114
Factory Setting List .............................................. 101
Master Settings .................................................... 102
Message List .......................................................... 94
MIDI Settings ........................................................ 101
Other Settings ...................................................... 101
Preset Performance List ....................................... 106
Program Change List ........................................... 105
Song Settings ....................................................... 102
Voice List .............................................................. 103
XG Drum Kit List ................................................... 112
XG Voice List ........................................................ 108
Load From Memory ....................................................... 79
Appendix
C
M
Main part ....................................................................... 27
[MASTER] button .......................................................... 39
[MASTER EDIT] button ................................................. 53
Master EQ ..................................................................... 36
MASTER EQ EDIT [▼][▲] buttons ................................ 72
Master Equalizer settings ............................................. 72
[MASTER EQUALIZER] sliders ..................................... 36
Master mode ................................................................. 39
Master settings ............................................................. 53
Master Volume .............................................................. 13
[MASTER VOLUME] dial ............................................... 13
Memory ......................................................................... 49
Memory Backup ............................................................ 71
CP300 Owner’s Manual
139
Index
Message List ................................................................ 94
MIDI [IN][OUT][THRU] connectors .............................. 90
MIDI channel ................................................................ 63
MIDI data compatibility ............................................... 100
MIDI Data Format ....................................................... 125
MIDI Implementation Chart ......................................... 137
[MIDI OUT] button ........................................................ 51
MIDI Panic .................................................................... 52
[MIDI SETTING] button ................................................. 64
MIDI Settings ................................................................ 63
Modulation wheel .......................................................... 34
O
[OTHER SETTING] button ............................................ 67
Other Settings ............................................................... 67
OUTPUT [L/MONO][R] jacks ........................................ 88
OUTPUT [L][R] jacks .................................................... 89
P
Appendix
Panel Lock .................................................................... 51
[PANEL LOCK] button .................................................. 51
Parameter
Master Edit ............................................................. 54
MIDI Settings ......................................................... 65
Other Settings ........................................................ 68
Song Settings ......................................................... 86
Voice Edit ............................................................... 58
Part EQ ......................................................................... 36
Pedal ............................................................................. 33
Pedal functions ....................................................... 61, 62
Perf. Name .................................................................... 78
[PERFORM.FILE] button ............................................... 76
Performance ................................................................. 77
rename ................................................................... 78
save to a button ..................................................... 77
[PERFORMANCE] button ............................................. 40
Performance file
basic operation ...................................................... 76
defined ................................................................... 73
delete ..................................................................... 80
recall from the storage memory ............................. 79
rename ................................................................... 80
save as ................................................................... 79
Performance functions .................................................. 73
Performance parameters .............................................. 74
[PHONES] jack ............................................................. 12
Pitch Bend wheel .......................................................... 34
[POWER] switch ..................................................... 11, 12
Precautions ..................................................................... 4
Preset ...................................................................... 18, 49
Preset Performance file ................................................ 40
Preset Performance List ............................................. 106
Program Change List .................................................. 105
Q
Quantize ....................................................................... 86
140
CP300 Owner’s Manual
R
[REC] button ................................................................. 42
Recording
Dual mode .............................................................. 48
live performance .............................................. 41, 42
Split mode .............................................................. 48
Recording Techniques
adding data ............................................................ 46
changing Tempo after recording ........................... 46
changing Voice after recording ............................. 46
overwriting .............................................................. 46
re-recording parts .................................................. 44
Recording track ............................................................ 42
Rename
Performance ........................................................... 78
Performance file ..................................................... 80
Song file ................................................................. 83
Rename File .................................................................. 80
Rename Song ............................................................... 83
Reverb .......................................................................... 35
[REVERB] button ........................................................... 35
S
Save
Performance ........................................................... 77
Performance file ..................................................... 79
Recorded Song ...................................................... 82
Save As ......................................................................... 79
Save To Memory ........................................................... 82
Scale ............................................................................. 68
[SOFT] jack ................................................................... 33
Soft pedal ...................................................................... 33
Song .............................................................................. 41
Song file
basic operation ...................................................... 81
defined ................................................................... 81
delete ..................................................................... 83
rename ................................................................... 83
save to memory ...................................................... 82
Song playback .............................................................. 49
Song Repeat ................................................................. 87
SONG SELECT [N][O] buttons ......................... 42, 49
Song Settings ................................................................ 85
[SONG VOLUME] slider ................................................ 47
[SOSTENUTO] jack ....................................................... 33
Sostenuto pedal ............................................................ 33
[SPEAKER] button ........................................................ 52
Speakers (built-in) On/Off ............................................. 52
Specifications ............................................................. 138
Split ............................................................................... 31
[SPLIT] button ............................................................... 31
Split Point ................................................................ 32, 69
Storage memory ............................................... 17, 73, 82
[SUSTAIN] jack ............................................................. 33
Sustain pedal ................................................................ 33
Synchro Start ................................................................ 50
System effect ................................................................ 35
Index
T
Tempo ........................................................................... 38
TEMPO [DOWN] [UP] buttons ...................................... 38
Time Signature .............................................................. 87
Touch ...................................................................... 61, 68
TRACK [1][2][3-16] buttons .................................... 42, 50
Transpose ..................................................................... 37
[TRANSPOSE] button ................................................... 37
Troubleshooting ............................................................ 98
Tune .............................................................................. 68
U
[USB] connector ........................................................... 92
V
VARIATION [▼][▲] buttons .......................................... 25
Voice ............................................................................. 25
Voice Edit ...................................................................... 56
[VOICE EDIT] button ..................................................... 56
Voice List .................................................................... 103
[VOICE/PERFORMANCE] button ...................... 25, 40, 73
Volume
adjusting each part ................................................ 28
adjusting Master Volume ................................. 13, 23
adjusting Song Volume .................................... 23, 47
Appendix
X
XG ............................................................................... 100
XG Drum Kit List ......................................................... 112
XG Voice ....................................................................... 26
XG Voice List .............................................................. 108
Z
Zone Control ........................................................... 28, 39
[ZONE CONTROL] sliders ...................................... 28, 39
CP300 Owner’s Manual
141
FCC INFORMATION (U.S.A.)
1. IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions contained in this manual, meets FCC requirements. Modifications not
expressly approved by Yamaha may void your authority, granted by
the FCC, to use the product.
2. IMPORTANT: When connecting this product to accessories and/
or another product use only high quality shielded cables. Cable/s
supplied with this product MUST be used. Follow all installation
instructions. Failure to follow instructions could void your FCC
authorization to use this product in the USA.
3. NOTE: This product has been tested and found to comply with the
requirements listed in FCC Regulations, Part 15 for Class “B” digital
devices. Compliance with these requirements provides a reasonable level of assurance that your use of this product in a residential
environment will not result in harmful interference with other electronic devices. This equipment generates/uses radio frequencies
and, if not installed and used according to the instructions found in
the users manual, may cause interference harmful to the operation
of other electronic devices. Compliance with FCC regulations does
* This applies only to products distributed by YAMAHA CORPORATION OF AMERICA.
IMPORTANT NOTICE FOR THE UNITED KINGDOM
Connecting the Plug and Cord
IMPORTANT. The wires in this mains lead are coloured in accordance
with the following code:
BLUE
: NEUTRAL
BROWN : LIVE
As the colours of the wires in the mains lead of this apparatus may not
correspond with the coloured makings identifying the terminals in your
plug proceed as follows:
The wire which is coloured BLUE must be connected to the terminal
which is marked with the letter N or coloured BLACK.
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED.
Making sure that neither core is connected to the earth terminal of the
three pin plug.
• This applies only to products distributed by Yamaha-Kemble Music (U.K.) Ltd.
(2 wires)
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE
BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOCS ÉLECTRIQUES,
INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA
BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU
FOND.
• This applies only to products distributed by Yamaha Canada Music Ltd.
(polarity)
• Ceci ne s’applique qu’aux produits distribués par Yamaha Canada Musique Ltée.
142
CP300 Owner’s Manual
not guarantee that interference will not occur in all installations. If
this product is found to be the source of interference, which can be
determined by turning the unit “OFF” and “ON”, please try to eliminate the problem by using one of the following measures:
Relocate either this product or the device that is being affected by
the interference.
Utilize power outlets that are on different branch (circuit breaker or
fuse) circuits or install AC line filter/s.
In the case of radio or TV interference, relocate/reorient the
antenna. If the antenna lead-in is 300 ohm ribbon lead, change the
lead-in to co-axial type cable.
If these corrective measures do not produce satisfactory results,
please contact the local retailer authorized to distribute this type of
product. If you can not locate the appropriate retailer, please contact Yamaha Corporation of America, Electronic Service Division,
6600 Orangethorpe Ave, Buena Park, CA90620
The above statements apply ONLY to those products distributed by
Yamaha Corporation of America or its subsidiaries.
(class B)
For details of products, please contact your nearest Yamaha
representative or the authorized distributor listed below.
Pour plus de détails sur les produits, veuillez-vous adresser à Yamaha ou
au distributeur le plus proche de vous figurant dans la liste suivante.
NORTH AMERICA
CANADA
Yamaha Canada Music Ltd.
135 Milner Avenue, Scarborough, Ontario,
M1S 3R1, Canada
Tel: 416-298-1311
Die Einzelheiten zu Produkten sind bei Ihrer unten aufgeführten
Niederlassung und bei Yamaha Vertragshändlern in den jeweiligen
Bestimmungsländern erhältlich.
Para detalles sobre productos, contacte su tienda Yamaha más cercana
o el distribuidor autorizado que se lista debajo.
THE NETHERLANDS/
BELGIUM/LUXEMBOURG
Yamaha Music Central Europe GmbH,
Branch Benelux
Clarissenhof 5-b, 4133 AB Vianen, The Netherlands
Tel: 0347-358 040
FRANCE
U.S.A.
Yamaha Corporation of America
6600 Orangethorpe Ave., Buena Park, Calif. 90620,
U.S.A.
Tel: 714-522-9011
CENTRAL & SOUTH AMERICA
MEXICO
Yamaha de México S.A. de C.V.
Calz. Javier Rojo Gómez #1149,
Col. Guadalupe del Moral
C.P. 09300, México, D.F., México
Tel: 55-5804-0600
BRAZIL
Yamaha Musical do Brasil Ltda.
Av. Reboucas 2636-Pinheiros CEP: 05402-400
Sao Paulo-SP. Brasil
Tel: 011-3085-1377
Yamaha Musique France
BP 70-77312 Marne-la-Vallée Cedex 2, France
Tel: 01-64-61-4000
ITALY
Yamaha Musica Italia S.P.A.
Combo Division
Viale Italia 88, 20020 Lainate (Milano), Italy
Tel: 02-935-771
SPAIN/PORTUGAL
Yamaha-Hazen Música, S.A.
Ctra. de la Coruna km. 17, 200, 28230
Las Rozas (Madrid), Spain
Tel: 91-639-8888
GREECE
Philippos Nakas S.A. The Music House
147 Skiathou Street, 112-55 Athens, Greece
Tel: 01-228 2160
SWEDEN
ARGENTINA
Yamaha Music Latin America, S.A.
Sucursal de Argentina
Viamonte 1145 Piso2-B 1053,
Buenos Aires, Argentina
Tel: 1-4371-7021
PANAMA AND OTHER LATIN
AMERICAN COUNTRIES/
CARIBBEAN COUNTRIES
Yamaha Music Latin America, S.A.
Torre Banco General, Piso 7, Urbanización Marbella,
Calle 47 y Aquilino de la Guardia,
Ciudad de Panamá, Panamá
Tel: +507-269-5311
EUROPE
THE UNITED KINGDOM
Yamaha-Kemble Music (U.K.) Ltd.
Sherbourne Drive, Tilbrook, Milton Keynes,
MK7 8BL, England
Tel: 01908-366700
IRELAND
Danfay Ltd.
61D, Sallynoggin Road, Dun Laoghaire, Co. Dublin
Tel: 01-2859177
GERMANY
Yamaha Music Central Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: 04101-3030
Yamaha Scandinavia AB
J. A. Wettergrens Gata 1
Box 30053
S-400 43 Göteborg, Sweden
Tel: 031 89 34 00
ASIA
THE PEOPLE’S REPUBLIC OF CHINA
Yamaha Music & Electronics (China) Co.,Ltd.
25/F., United Plaza, 1468 Nanjing Road (West),
Jingan, Shanghai, China
Tel: 021-6247-2211
HONG KONG
Tom Lee Music Co., Ltd.
11/F., Silvercord Tower 1, 30 Canton Road,
Tsimshatsui, Kowloon, Hong Kong
Tel: 2737-7688
INDONESIA
PT. Yamaha Music Indonesia (Distributor)
PT. Nusantik
Gedung Yamaha Music Center, Jalan Jend. Gatot
Subroto Kav. 4, Jakarta 12930, Indonesia
Tel: 21-520-2577
KOREA
Yamaha Music Korea Ltd.
Tong-Yang Securities Bldg. 16F 23-8 Yoido-dong,
Youngdungpo-ku, Seoul, Korea
Tel: 02-3770-0660
MALAYSIA
Yamaha Music Malaysia, Sdn., Bhd.
Lot 8, Jalan Perbandaran, 47301 Kelana Jaya,
Petaling Jaya, Selangor, Malaysia
Tel: 3-78030900
PHILIPPINES
DENMARK
YS Copenhagen Liaison Office
Generatorvej 6A
DK-2730 Herlev, Denmark
Tel: 44 92 49 00
FINLAND
F-Musiikki Oy
Kluuvikatu 6, P.O. Box 260,
SF-00101 Helsinki, Finland
Tel: 09 618511
Yupangco Music Corporation
339 Gil J. Puyat Avenue, P.O. Box 885 MCPO,
Makati, Metro Manila, Philippines
Tel: 819-7551
SINGAPORE
Yamaha Music Asia Pte., Ltd.
#03-11 A-Z Building
140 Paya Lebor Road, Singapore 409015
Tel: 747-4374
TAIWAN
NORWAY
Norsk filial av Yamaha Scandinavia AB
Grini Næringspark 1
N-1345 Østerås, Norway
Tel: 67 16 77 70
ICELAND
Skifan HF
Skeifan 17 P.O. Box 8120
IS-128 Reykjavik, Iceland
Tel: 525 5000
Yamaha KHS Music Co., Ltd.
3F, #6, Sec.2, Nan Jing E. Rd. Taipei.
Taiwan 104, R.O.C.
Tel: 02-2511-8688
THAILAND
Siam Music Yamaha Co., Ltd.
891/1 Siam Motors Building, 15-16 floor
Rama 1 road, Wangmai, Pathumwan
Bangkok 10330, Thailand
Tel: 02-215-2626
OTHER ASIAN COUNTRIES
OTHER EUROPEAN COUNTRIES
Yamaha Music Central Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: +49-4101-3030
Yamaha Corporation,
Asia-Pacific Music Marketing Group
Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650
Tel: +81-53-460-2317
SWITZERLAND/LIECHTENSTEIN
Yamaha Music Central Europe GmbH,
Branch Switzerland
Seefeldstrasse 94, 8008 Zürich, Switzerland
Tel: 01-383 3990
AUSTRIA
Yamaha Music Central Europe GmbH,
Branch Austria
Schleiergasse 20, A-1100 Wien, Austria
Tel: 01-60203900
CZECH REPUBLIC/SLOVAKIA/
HUNGARY/SLOVENIA
Yamaha Music Central Europe GmbH,
Branch Austria, CEE Department
Schleiergasse 20, A-1100 Wien, Austria
Tel: 01-602039025
POLAND
Yamaha Music Central Europe GmbH
Sp.z. o.o. Oddzial w Polsce
ul. 17 Stycznia 56, PL-02-146 Warszawa, Poland
Tel: 022-868-07-57
OCEANIA
AFRICA
Yamaha Corporation,
Asia-Pacific Music Marketing Group
Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650
Tel: +81-53-460-2312
AUSTRALIA
Yamaha Music Australia Pty. Ltd.
Level 1, 99 Queensbridge Street, Southbank,
Victoria 3006, Australia
Tel: 3-9693-5111
NEW ZEALAND
MIDDLE EAST
TURKEY/CYPRUS
Yamaha Music Central Europe GmbH
Siemensstraße 22-34, 25462 Rellingen, Germany
Tel: 04101-3030
OTHER COUNTRIES
Yamaha Music Gulf FZE
LB21-128 Jebel Ali Freezone
P.O.Box 17328, Dubai, U.A.E.
Tel: +971-4-881-5868
Music Houses of N.Z. Ltd.
146/148 Captain Springs Road, Te Papapa,
Auckland, New Zealand
Tel: 9-634-0099
COUNTRIES AND TRUST
TERRITORIES IN PACIFIC OCEAN
Yamaha Corporation,
Asia-Pacific Music Marketing Group
Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650
Tel: +81-53-460-2312
HEAD OFFICE Yamaha Corporation, Pro Audio & Digital Musical Instrument Division
Nakazawa-cho 10-1, Hamamatsu, Japan 430-8650
Tel: +81-53-460-2445
SY37
Yamaha Web Site (English only)
http://www.yamahasynth.com/
Yamaha Manual Library
http://www.yamaha.co.jp/manual/
U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation
© 2006 Yamaha Corporation
This document is printed on chlorine free (ECF) paper with soy ink.
WG78300 602MWDH24.2-01A0
Printed in Japan