Motorola MBP35BL User`s guide

USER’S GUIDE
MBP35BL, MBP35BW
BABY MONITOR
USER’S GUIDE
The features described in this user’s guide are subject to
modifications without prior notice.
Welcome...
to your new Motorola Baby Monitor!
Thank you for purchasing the MBP35BL, MBP35BW. Now you can
see and hear your baby sleeping in the other room or you can
monitor your older children in their playroom.
Please retain your original dated sales receipt for your records. For
warranty service of your Motorola product, you will need to provide
a copy of your dated sales receipt to confirm warranty status.
Registration is not required for warranty coverage.
For product related questions, please call:
0845 218 0890 in the UK
(65) 68412668 in Singapore
On the Web: www.motorola.com
This User’s Guide provides you with all the information you need
to get the most from your product.
Before you can use the baby monitor, you’ll need to insert and
fully charge the battery on the Parent unit. Please read the Safety
Instructions on page 6 before you install the units.
Got everything?
•
1 x Parent unit
•
1 x Baby unit
•
1 x Rechargeable Ni-MH battery pack for the Parent unit
•
1 x Power adapter for the Parent unit
•
1 x Power adapter for the Baby unit
IMPORTANT
The non-rechargeable batteries for the Baby unit are not supplied
with your product. We recommend the batteries to be installed
before use, so that the unit continues to work in the event of a
mains power failure.
Overview of your Parent unit
1
12
5
13
2
6
11
TALK
MENU
9
8
7
10
3
4
1. Display (LCD screen)
2. Up < / Down > keys
Normal mode: Adjust
speaker volume
Menu mode: Adjust setting
3. Power and Low battery LED
4. Voice Activation ))) LED
5. Lullaby Play/Stop key i
Press once to play lullaby.
Press again to stop playing.
6. Lullaby selection key j
Press to select a lullaby
during playback.
7. Microphone
8. Menu key m
Press to open the Menu
options
9. Talk key t
Press and hold to speak to
your baby.
10. Power key p
Press and hold to turn on/off
the unit.
11. Antenna
12. Battery cover
13. Speaker
Parent unit display symbols
Indicates that the Baby Unit is out of range or not linked to the
Parent Unit.
Appears when setting the Temperature mode.
High Appears when the temperature goes above 26°C (79°F).
Low
Appears when the temperature goes below 14°C (57°F).
Appears when setting the Night Light function.
Indicates that the Talk function is activated.
Appears when the Lullaby function is activated.
Appears when adjusting the Volume of the Parent Unit.
Appears when adjusting the Brightness of the Parent Unit display.
Parent Unit display symbols (cont’d)
Appears when the Parent Unit is in registration mode.
VOX
Appears when setting the Voice Activation level.
Overview of your Baby unit
1
7
2
3
8
6
4
9
5
1.
2.
3.
4.
5.
Photo sensor
Camera lens
Infrared LEDs
Power LED
Night lights
6.
7.
8.
9.
On/Off switch
Speaker
Antenna
Temperature sensor
Important guidelines for installing your Baby Monitor
•
•
•
•
•
To use your video monitor baby and parent unit together, you must
be able to establish a radio link between them, and the range will be
affected by environmental conditions.
Any large metal object, like a refrigerator, a mirror, a filing cabinet,
metallic doors or reinforced concrete, between the baby and parent
unit may block the radio signal.
The signal strength may also be reduced by other solid structures,
like walls, or by radio or electrical equipment, such as TV's,
computers, cordless or mobile phones, fluorescent lights or dimmer
switches.
Use of other 2.4GHz products, such as wireless networks,
Bluetooth® systems or microwave ovens may cause interference
with this product, so keep the baby monitor away from these types
of products, or turn them off if they appear to be causing
interference.
If the signal is poor, try moving the parent and/or the baby unit to
different positions in the rooms.
1. Safety Instructions ......................................................................... 6
2. Getting started................................................................................ 7
2.1
2.2
2.3
2.4
2.5
Baby unit battery installation...........................................................7
Baby unit power supply ..................................................................8
Parent unit battery Installation ........................................................8
Parent unit power supply ................................................................9
Registration ..................................................................................10
3. Using the Baby Monitor MBP35BL, MBP35BW ......................... 11
3.1
3.2
3.3
3.4
3.5
Setting up .....................................................................................11
Night vision ...................................................................................11
Talk function .................................................................................11
Adjusting the volume of the Parent Unit .......................................11
Playing a lullaby for your baby......................................................12
4. MBP35BL, MBP35BW Parent Unit Menu Options ..................... 13
4.1
4.2
4.3
4.4
5.
6.
7.
8.
Brightness.....................................................................................13
Temperature Display (ºC or ºF) ....................................................13
Night Light ....................................................................................13
Voice Activation ............................................................................14
Disposal of the device (environment) ........................................ 15
Cleaning ........................................................................................ 16
Help................................................................................................ 17
General Information ..................................................................... 18
Table of contents
5
ENGLISH
Table of contents
1. Safety Instructions
WARNING
This baby monitor is compliant with all relevant standards regarding
electromagnetic fields and is, when handled as described in the User’s
Guide, safe to use. Therefore, always read the instructions in this User’s
Guide carefully before using the device.
• Adult assembly is required. Keep small parts away from children when
assembling.
• This product is not a toy. Do not allow children to play with it.
• This baby monitor is not a substitute for responsible adult supervision.
• Keep this User’s Guide for future reference.
• Do not place the baby unit or cables in the cot or within arm's reach of
the baby (the unit should be at least 1 metre away).
• Keep the cords out of reach of children.
• Do not cover the baby monitor with a towel or blanket.
• Never use extension cords with power adapters. Only use the power
adapters provided.
• Test the baby monitor before use. Become familiar with its functions.
• Do not use the baby monitor near water.
• Do not install the baby monitor near a heat source.
• Only use the chargers and power adapters provided. Do not use other
chargers or power adapters as this may damage the device and
batteries.
• For the parent unit, only insert a rechargeable battery pack of the
same type. For the baby unit, use non-rechargeable batteries and
insert with the correct polarity, as indicated in the battery compartment
and in “2.1 Baby unit battery installation”.
• Do not touch the charger or plug contacts with sharp or metal objects.
CAUTION
Risk of explosion if battery is replaced by an incorrect type. Dispose of
used batteries according to the instructions.
6
Safety Instructions
2.1
Baby unit battery installation
The camera uses either 3 AA size batteries (non-rechargeable batteries
recommended) or the household power mains. The Baby unit has no
charging function!
screw
IMPORTANT
The non-rechargeable batteries for the Baby unit are not supplied with
your product. We recommend the batteries to be installed before use, so
that the unit continues to work in the event of a mains power failure.
1. Loosen the screw in a counterclockwise direction using a small
screwdriver. Remove the battery cover.
2. Install the 3 AA non-rechargeable batteries following the polarity as
shown in the compartment. Close the battery compartment and
tighten the screw in a clockwise direction.
3. Slide the power switch to the ON position. The power LED will light up
in green.
To switch off the baby unit, slide the power switch to the OFF position.
NOTE
When the battery level is low, the power LED will turn orange and will flash.
WARNING
Do not mix old batteries with new ones.
Keep batteries away from small children.
Do not short-circuit batteries or dispose of in fire.
Remove the batteries if this device is not going to be used for a long
period of time.
Getting started
7
ENGLISH
2. Getting started
2.2
Baby unit power supply
1. Connect the small plug of the power adapter to the baby unit and the
other end to the mains socket (230V/50Hz).
NOTE
Only use the enclosed power adapter (6V DC / 800mA).
2. Slide the power switch to the ON position. The power LED will light up
in green.
3. To switch off the baby unit, slide the power switch to OFF position.
2.3
Parent unit battery Installation
Black
8
Red
Getting started
NOTE
When the battery level is low, the power LED will turn orange and will
flash. Charge the battery pack for at least 15 hours before using on
battery power only.
NOTE
When the unit is powered up with either the power adapter or using the
rechargeable battery pack, the LED will light up in green. If both the
power adapter and rechargeable battery pack are used, the LED will light
up in red.
2.4
Parent unit power supply
1. Connect the small plug of the power adapter to the parent unit and
the other end to the mains socket (230V/50Hz).
NOTE
Only use the enclosed power adapter (6V DC / 800mA).
Getting started
9
ENGLISH
1. Loosen the screw in a counterclockwise direction using a small
screwdriver. Remove the battery cover.
2. Insert the wire tab of the rechargeable battery pack into the contact
slot as shown above and fit the battery pack into the compartment.
3. Close the battery compartment and tighten the screw in a clockwise
direction.
4. Press and hold p to switch ON the parent unit.
- It will take a few seconds to start up the unit.
5. Press and hold p to switch OFF the parent unit.
2. Press and hold p to switch ON the parent unit. The power LED
will light up in green.
3. Press and hold p to switch OFF the parent unit.
NOTE
Once the baby and parent units are switched on, the display on the parent
unit will show the video captured by the baby unit. When the VOX mode
is on, the screen will turn off after a few seconds if the sound near the
baby unit drops below the Voice Activation threshold level of the unit.
When there is no connection or out of range, the
icon on the LCD
display will flash and the parent unit will beep continuously. Move the
parent unit closer to the baby unit until the link is re-established.
2.5
Registration
The Baby monitor is pre-registered to your Parent Unit. You do not need
to register it again unless the Baby Unit loses its link with the Parent Unit.
To re-register your Baby Unit, or register a new Baby Unit, follow the
procedure below:
1. Switch off the Baby Unit
2. Press and hold the m button on the Parent Unit until
appears on the display screen.
3. Then press the m button to confirm the selection and enter the
registration mode.
..... will appear on the screen for up to 15
seconds.
4. Switch the Baby Unit ON to enter the registration mode. The power
LED on the Baby Unit flashes quickly for approximately 3 seconds.
The registration is completed when
.....OK appears and then the
video captured by Baby Unit’s camera appears on the display screen of
the Parent Unit.
.....X appears and then both the Parent
If the registration fails then
and Baby Unit return to normal mode.
NOTE
If a particular Baby Unit had been registered already, registering this
current Baby Unit again will over-write the old registration.
10
Getting started
3.1
ENGLISH
3. Using the Baby Monitor MBP35BL,
MBP35BW
Setting up
• Place the camera in a convenient location and point the lens of the
camera towards the area you want to monitor.
• Tilt the head of the baby unit up or down to your desired position until
the parent unit gets a good reception of the baby.
NOTE
Do not place the camera within baby’s reach! If there is interference on
the picture or sound, try moving the units to different locations, and
ensure they are not close to other electrical equipment.
3.2
Night vision
The camera has 4 high-intensity infrared LEDs for picking up clear
images in the dark. When the built-in photo sensor detects a low level of
ambient light, the LEDs will automatically activate and the screen on the
parent unit will display in black and white.
NOTE
If the ambient light near the Baby Unit is marginal, the screen may appear
to flicker between colour and black and white.
3.3
Talk function
3.4
Adjusting the volume of the Parent Unit
Press and hold t on the Parent unit to talk to your baby through the
Baby unit loudspeaker. The symbol
will be displayed in the middle
of the LCD screen.
1. Press < and > to adjust the volume (5 levels) of the Parent Unit
during normal operations, and
(5 volume levels) appears on
the display screen.
Using the Baby Monitor MBP35BL, MBP35BW
11
3.5
Playing a lullaby for your baby
You can remotely activate a lullaby to be played on the Baby Unit.
1. Press the i button on the Parent Unit to play the last set lullaby.
2. To select another lullaby, press j during playback. There are 5
lullabies available for selection, indicated by
or
1,
2,
3,
4
5.
3. To play all lullabies, press j until
4. Press i again to stop playback.
is displayed on the display screen.
TIPS
• During the first 10 seconds of lullaby playback, pressing < or > will
adjust the lullaby volume of the Baby Unit.
appears on the
display screen.
• Pressing < or > after 10 seconds of lullaby playback will adjust the
volume of the Parent Unit.
appears on the display screen.
12
Using the Baby Monitor MBP35BL, MBP35BW
4.1
ENGLISH
4. MBP35BL, MBP35BW Parent Unit
Menu Options
Brightness
1. Press m repeatedly until
appears on the display screen.
2. Press < and > to adjust the LCD brightness level to 1, 2, 3, 4, or 5 (the
default setting is 3). The LCD brightness will be adjusted accordingly.
3. Press m repeatedly to exit.
4.2
Temperature Display (ºC or ºF)
1. Press m repeatedly until
appears on the display screen.
2. Press < and > to change the temperature display to ºC, ºF or OFF
(the default setting is ºC). The temperature unit and reading will be
changed accordingly.
3. Press m repeatedly to exit.
NOTE
If the temperature goes above 26ºC (79ºF),
screen.
If the temperature goes below 14ºC (57ºF),
screen.
4.3
High appears on the LCD
Low appears on the LCD
Night Light
The Baby Unit has a night light feature that provides a dim light and is
controlled from the Parent Unit.
1. Press m repeatedly until
appears on the display screen.
2. Press < to turn the Baby Unit Night Light ON or press > to turn the
Night Light OFF. The night light on the Baby Unit will be switched on
and off accordingly.
3. Press m repeatedly to exit.
MBP35BL, MBP35BW Parent Unit Menu Options
13
4.4
Voice Activation
If you do not want the parent unit screen to be on continually, you can set
the VOX mode so that the screen only turns on if there is a sound near
the baby unit. The sound detection sensitivity level (VOX) of the Baby
Monitor can be adjusted. If the baby is a quiet sleeper, the sensitivity level
can be increased so that only minor disturbances will cause the parent
unit screen to turn back on.
1. Press m repeatedly until VOX appears on the LCD screen.
Press < and > to adjust the VOX level to OFF, 1, 2, 3, 4 or 5 (the default
setting is OFF).
When the VOX function is on (level 1 to 5), the Voice Activation ))) LED
will be turned on, and the LCD screen will switch off after a few seconds
if the detected sound is below the level selected.
Note: Level 5 is the most sensitive and so will need to be the quietest
before the LCD will switch off.
2. Press m repeatedly to exit.
NOTE
When the Voice Activation function is on, the voice Activation LED will be
turned on (red) and the display screen will switch off after a few seconds.
The LCD screen on the parent unit will be switched back on when the
sound level of the baby reaches the Voice Activation threshold or when
any key on the parent unit is pressed.
14
MBP35BL, MBP35BW Parent Unit Menu Options
ENGLISH
5. Disposal of the device
(environment)
At the end of the product lifecycle, you should not dispose
of this product with normal household waste, but take the
product to a collection point for the recycling of electrical
and electronic equipment. The symbol on the product,
user’s guide and/or box indicates this.
Some of the product materials can be re-used if you take
them to a recycling point. By reusing some parts or raw materials from
used products you make an important contribution to the protection of the
environment.
Please contact your local authorities in case you need more information on
the collection points in your area.
Dispose of the batteries in an environmentally-friendly manner according
to your local regulations.
Disposal of the device (environment)
15
6. Cleaning
Clean the MBP35BL, MBP35BW with a slightly damp cloth or with an antistatic cloth. Never use cleaning agents or abrasive solvents.
Cleaning and care
• Do not clean any part of the product with thinners or other solvents
and chemicals –- this may cause permanent damage to the product
which is not covered by the Warranty. When necessary, clean it with a
damp cloth.
• Keep your MBP35BL, MBP35BW away from hot, humid areas or
strong sunlight, and don’t let it get wet.
• Every effort has been made to ensure high standards of reliability for
your MBP35BL, MBP35BW. However, if something does go wrong,
please do not try to repair it yourself –- contact Customer Service for
assistance.
16
Cleaning
ENGLISH
7. Help
Display
No display
• Try recharging or replacing the batteries.
• Reset the units. Unplug the units’ electrical power, including the
batteries and both mains adapters, then plug them back in.
• Is the unit turned on?
Press and hold p on the parent unit to turn it on.
Is the VOX mode on?
• Turn the VOX off (see “4.4 Voice Activation”) to keep the screen on
continually.
Registration
If the baby unit has lost its link with the parent unit
• Try recharging or replacing the batteries.
• If the baby unit is too far away it may be going out of range, so move
the baby unit closer to the parent unit.
• Reset the units by unplugging the units’ batteries and mains electrical
power. Wait for around 15 seconds and plug it back in again. Allow up
to one minute for the baby unit and the parent unit to synchronise.
• See “2.5 Registration” if there is a need to re-register the units.
Interference
Noise interference on your parent unit
• Your baby and parent units may be too close. Move them further away
from each other.
• Make sure there is at least 1 metre between the 2 units to avoid
feedback howling.
• If the baby unit is too far away it may be going out of range, so move
the baby unit closer to the parent unit.
• Make sure the baby and parent units are not near other electrical
equipment, such as a television, computer or cordless/mobile telephone.
Help
17
8. General Information
If your product is not working properly....
1. Read this User’s Guide or the Quick Start Guide.
2. Visit our website:
www.motorola.com
3. Contact Customer Service at:
0845 218 0890 in the UK
(65) 68412668 in Singapore
To order a replacement battery, contact customer service or visit our
website.
Consumer Products and Accessories purchased in
the United Kingdom and Singapore
What Does this Warranty Cover?
Subject to the exclusions and limitations contained below, Binatone
Electronics International LTD. warrants the Motorola branded consumer
products that it manufactures (“Products”) and the Motorola branded or
certified accessories sold for use with these Products that it manufactures
(“Accessories”) to be free from defects in materials and workmanship
under normal consumer usage for the period(s) outlined below. This
limited warranty is a consumer’s exclusive remedy, and only applies as
follows to new Motorola branded Products and Accessories
manufactured by Binatone Electronics International LTD., and purchased
by consumers in the United Kingdom and Singapore, which are
accompanied by this written warranty:
Who is covered?
This warranty covers only the first consumer purchaser, and is not
transferable.
18
General Information
BINATONE ELECTRONICS INTERNATIONAL LTD., at its sole option,
will at no charge repair, replace or refund the purchase price of any
Products or Accessories that does not conform to this warranty. Binatone
Electronics International LTD. may use functionally equivalent
reconditioned/ refurbished/ pre-owned or new Products, Accessories or
parts in such repair or replacement and any Products, Accessories or
parts removed or being replaced under this warranty become the
property of Binatone Electronics International LTD.
What Other Limitations Are There?
ANY IMPLIED WARRANTIES OR CONDITIONS IRRESPECTIVE OF
WHETHER THEY ARE IMPOSED BY LAW OR OTHERWISE,
INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
SHALL BE LIMITED TO THE DURATION OF THIS LIMITED
WARRANTY, OTHERWISE THE REPAIR, REPLACEMENT, OR
REFUND AS PROVIDED UNDER THIS EXPRESS LIMITED WARRANTY
IS THE EXCLUSIVE REMEDY OF THE CONSUMER, AND IS
PROVIDED IN LIEU OF ALL WARRANTIES AND MOTOROLA AND
BINATONE ELECTRONICS INTERNATIONAL LTD. MAKES NO OTHER
WARRANTIES OR CONDITIONS, EXPRESS OF IMPLIED. IN NO
EVENT SHALL MOTOROLA OR BINATONE ELECTRONICS
INTERNATIONAL LTD. BE LIABLE, WHETHER UNDER THIS LIMITED
WARRANTY OR IN CONTRACT OR TORT (INCLUDING NEGLIGENCE
OR STRICT PRODUCT LIABILITY) OR OTHERWISE FOR DAMAGES
OR CLAIMS IN EXCESS OF THE PURCHASE PRICE OF THE
PRODUCT OR ACCESSORY, OR FOR ANY INDIRECT, INCIDENTAL,
SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY KIND, OR LOSS
OF REVENUE, SAVINGS OR PROFITS, LOSS OF BUSINESS, LOSS OF
PROGRAMS DATA INFORMATION (WHETHER CONFIDENTIAL
PROPRIETARY OR PERSONAL IN NATURE OR OTHERWISE) OR
OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION
WITH THE ABILITY OR INABILITY TO USE THE PRODUCTS OR
General Information
19
ENGLISH
What will BINATONE ELECTRONICS INTERNATIONAL LTD.
do?
ACCESSORIES AND BINATONE ELECTRONICS INTERNATIONAL
LTD. SHALL UNDER NO CIRCUMSTANCES BE LIABLE FOR ANY
CLAIMS OR DEMANDS MADE BY ANY THIRD PARTY OR MADE BY
YOU ON BEHALF OF ANY THIRD PARTY TO THE FULL EXTENT
THESE DAMAGES OR CLAIMS MAY BE DISCLAIMED BY LAW.
Some states, countries or jurisdictions do not allow the limitation or
exclusion of incidental or consequential damages, or limitation on the
length of an implied warranty, so the above limitations or exclusions may
not apply to you in such states, countries or jurisdictions. This warranty
gives you specific legal rights, and you may also have other rights that
vary from state to state or from one country/jurisdiction to another.
Products or Accessories
Length of Coverage
Covered
Consumer Products
One (1) year from the date of
purchase by the first consumer
purchaser of the product.
Consumer Accessories
Ninety (90) days from the date of
purchase by the first consumer
purchaser of the accessory.
The balance of the original
Consumer Products and
Accessories that are Repaired warranty or for ninety (90) days
from the date returned to the
or Replaced
consumer, whichever is longer.
Exclusions
Normal Wear and Tear. Periodic maintenance, repair and replacement
of parts due to normal wear and tear are excluded from coverage.
Batteries. Only batteries whose fully charged capacity falls below 80% of
their rated capacity and batteries that leak are covered by this limited
warranty. Battery life and the changes in battery capacity with time or use
are excluded from this warranty.
20
General Information
Use of Non-Motorola branded Products and Accessories. Defects or
damage that result from the use of Non-Motorola branded or certified
Products or Accessories or other peripheral equipment are excluded from
coverage.
Unauthorised Service or Modification. Defects or damages resulting
from service, testing, adjustment, installation, maintenance, alteration, or
modification in any way by someone other than Motorola, Binatone
Electronics International LTD. or its authorised service centres, are
excluded from coverage.
Altered Products. Products or Accessories with (a) serial numbers or
date tags that have been removed, altered or obliterated; (b) broken seals
or that show evidence of tampering; (c) mismatched board serial
numbers; or (d) nonconforming or non-Motorola branded housings, or
parts, are excluded from coverage.
Communication Services. Defects, damages, or the failure of Products
or Accessories due to any communication service or signal you may
subscribe to or use with the Products or Accessories is excluded from
coverage.
General Information
21
ENGLISH
Abuse & Misuse. Defects or damage that result from: (a) improper or
unreasonable use, operation, storage, misuse or abuse, accident or
neglect or other external cause, such as physical damage (cracks,
scratches, etc.) to the surface of the product resulting from misuse; (b)
your failure to follow or operate outside the usage parameters stated in
the user instructions that came with the Products or Accessories; (c)
contact with liquid, water, rain, extreme humidity or heavy perspiration,
sand, dirt or the like, extreme heat, or food; (d) use of the Products or
Accessories for commercial purposes or subjecting the Product or
Accessory to abnormal usage or conditions; or (e) other acts or omissions
which are not the fault or neglect of Motorola or Binatone Electronics
International LTD., are excluded from coverage.
How to Obtain Warranty Service or Other Information?
To obtain service or information, please call:
0845 218 0890 in the UK
(65) 68412668 in Singapore
You will receive instructions on how to ship the Products or Accessories,
the shipment of which shall be at your own risk and expense, to a
BINATONE ELECTRONICS INTERNATIONAL LTD. Authorised Repair
Centre. To obtain service, you must include: (a) a copy of your receipt, bill
of sale or other comparable proof of purchase of the Products or
Accessories showing the date of purchase; (b) a written description of the
problem; and, most importantly; (c) your address and telephone number.
These terms and conditions constitute the complete warranty agreement
between you and BINATONE ELECTRONICS INTERNATIONAL LTD.
regarding the Products or Accessories purchased by you, and supersede
any prior agreement or representations, including representations made
in any literature publications or promotional materials issued by
BINATONE ELECTRONICS INTERNATIONAL LTD. or representations
made by any agent employee or staff of BINATONE ELECTRONICS
INTERNATIONAL LTD., that may have been made in connection with the
said purchase.
22
General Information
ENGLISH
Technical Specifications
Baby unit
Frequency
2.4GHz to 2.4835GHz
Maximum range
Extended range up to 450 feet*
*Based on unobstructed line of sight. Actual range will
vary depending on surroundings.
Image sensor
Colour CMOS
Lens
f 2.5mm, F 2.8
IR LED
4 pcs
Power
Adapter:
Input — 100-240VAC, 50/60Hz (VDE/BS plug);
Output — 6VDC, 800 mA
(Supplier: Sure-power, Model: SW-060080EU/
SW-060080BS)
OR
Battery: 3xAA non-rechargeable batteries
(Note: Batteries are not included)
Parent unit
Frequency
Display
Display colours
Brightness control
Power
General Information
2.4GHz to 2.4835GHz
3.5" TFT LCD
16.7M colour LCD
5 steps
Adapter:
Input — 100-240VAC, 50/60Hz (VDE/BS plug);
Output — 6VDC, 800 mA
(Supplier: Sure-power, Model: SW-060080EU/
SW-060080BS)
OR
Battery: Ni-MH rechargeable battery pack
(Supplier: Desay, Model: AA2000; Supplier: TFL,
Model: TFL3X49AA2000-CD99-01A)
WARNING
Do not use non-rechargeable batteries for the
Parent Unit. Risk of explosion if battery is replaced
by an incorrect type. Dispose of used batteries
according to the instructions.
23
24
General Information
Manufactured, distributed or sold by
Binatone Electronics International LTD.,
official licensee for this product.
MOTOROLA and the Stylized M Logo,
and other Motorola trademarks and trade
dress are owned by Motorola, Inc. and
are used under license from Motorola,
Inc. MOTOROLA and the Stylized M
Logo are registered in the US Patent &
Trademark Office. All other product or
service names are the property of their
respective owners.
© Motorola, Inc. 2010. All rights reserved.
Version 1.0
Printed in China