Enrange XLTX Transmitter-Hazardous Locations Manual 198-80202-1001

Enrange XLTX Transmitter

(Intrinsically Safe)

Radio Remote Control

September 2015

Part Number: 198-80202-1001 R2

©Copyright 2015 Magnetek

Your New Radio Remote

Thank you for your purchase of Magnetek’s XLTX Radio Remote Control. Magnetek has set a whole new standard in radio-remote performance, dependability, and value with this unique new line of bellybox transmitters.

If your product ever needs modification or service, please contact one of our representatives at the following locations:

U.S. Service Information

For questions regarding service or technical information contact:

+1.866.MAG.SERV

+1.866.624.7378

International Service

+1.262.783.3500

World Headquarters:

Magnetek, Inc.

N49 W13650 Campbell Drive

Menomonee Falls, WI 53051

Telephone: +1.800.288.8178

Website:

e-mail: www.magnetek.com [email protected]

Fax Numbers:

Main:

Sales:

+1.800.298.3503

+1.262.783.3510

Service: +1.262.783.3508

Canada Service Information:

4090B Sladeview Crescent

Mississauga, Ontario

L5L 5Y5 Canada

Phone: +1.800.792.7253

Fax: +1.905.828.5707

+1.416.424.7617 (24/7 Service pager)

EU Market Contact:

Brian Preston

Magnetek (UK) Ltd.

Unit 3 Bedford Business Centre

Mile Road

Bedford, MK42 9TW UK

Phone: +44.1234.349191

Fax: +44.1234.268955

©2015 MAGNETEK

All rights reserved. This notice applies to all copyrighted materials included with this product, including, but not limited to, this manual and software embodied within the product. This manual is intended for the sole use of the person(s) to whom it was provided, and any unauthorized distribution of the manual or dispersal of its contents is strictly forbidden. This manual may not be reproduced in whole or in part by any means whatsoever without the expressed written permission of MAGNETEK.

Enrange XLTX Intrinsically Safe

Transmitter Instruction Manual

September 2015

Page 2 of 34

TABLE OF CONTENTS

1 INTRODUCTION ...................................................................................................................... 5

1.1

PRODUCT MANUAL SAFETY INFORMATION ............................................................... 5

1.2

WARNINGS and CAUTIONS ............................................................................................ 6

2 CRITICAL INSTALLATION CONSIDERATIONS ..................................................................... 7

2.1

GENERAL ......................................................................................................................... 7

2.2

PERSONS AUTHORIZED TO OPERATE RADIO CONTROLLED EQUIPMENT ........... 7

2.3

SAFETY INFORMATION AND RECOMMENDED TRAINING FOR RADIO

CONTROLLED EQUIPMENT OPERATORS .............................................................................. 8

2.4

TRANSMITTER UNIT ....................................................................................................... 9

2.5

PRE-OPERATION TEST .................................................................................................. 9

2.6

HANDLING BATTERIES ................................................................................................... 9

2.7

OPTIONAL RECHARGEABLE BATTERY CHARGING ................................................. 10

2.8

BATTERY DISPOSAL ..................................................................................................... 10

2.9

CRANE/LIFTING DEVICE SPECIFIC WARNINGS ........................................................ 11

2.10

SPECIFIC CONDITIONS OF SAFE USE ................................................................... 12

3 XLTX TRANSMITTER STANDARD CONFIGURATION AND OPERATION ........................ 13

3.1

INSTALLING BATTERY PACK ....................................................................................... 14

3.1.1

Approved Batteries for Intrinsically Safe Operation ................................................. 14

3.1.2

Intrinsically Safe Alkaline Battery Pack .................................................................... 14

3.1.3

Spare Battery Storage Compartment ...................................................................... 16

3.2

TURNING THE TRANSMITTER ON AND OFF .............................................................. 16

3.2.1

Turning On the Transmitter (with Standard Status LED Indicator(s)) ...................... 17

3.2.2

Turning On the Transmitter (with Optional Graphic User Interface Screen) ........... 17

3.2.3

Pulling In the Machine Stop Relay ........................................................................... 18

3.2.4

Turning Off the Transmitter ...................................................................................... 18

3.3

MACHINE STOP SWITCH (FOR EMERGENCY STOPPING ONLY)............................ 18

3.4

POWER/STATUS AND BATTERY LED ......................................................................... 18

3.5

OPTIONAL GRAPHIC USER INTERFACE .................................................................... 18

3.6

NORMAL OPERATING MODE WITH STANDARD STATUS LED(S) ........................... 18

3.6.1

Transmitters Equipped with Separate Power/Status and Battery LED Indicators ... 19

3.6.2

Transmitters Equipped with Single Status/Battery LED Indicator ........................... 19

3.7

NORMAL OPERATING MODE WITH OPTIONAL GRAPHIC USER INTERFACE ....... 20

3.7.1

Watch Dog Indicator (Spinning Arrow) .................................................................... 20

3.7.2

Command Confirmation ........................................................................................... 20

3.7.3

Battery Life Indicator ................................................................................................ 20

3.7.4

Signal Strength Indicator ......................................................................................... 21

3.7.5

Two-Way Feedback System .................................................................................... 21

3.8

JOYSTICKS AND PADDLES/LEVERS .......................................................................... 21

3.9

ROTARY SELECTOR SWITCH ..................................................................................... 21

3.10

AUXILIARY SWITCHES .............................................................................................. 21

3.11

CONNECTING THE XLTX TO A COMPUTER ........................................................... 22

4 TRANSMITTER SETUP ......................................................................................................... 23

4.1

TRANSMITTER SETUP SETTINGS WITH STANDARD STATUS LEDS ..................... 23

4.1.1

RF Channel Setting Override ................................................................................... 23

4.1.2

RF Channel Setting Selection .................................................................................. 23

4.1.3

IR Configuration Receiver ........................................................................................ 25

4.2

USING THE TRANSMITTER IN SETUP MODE (WITH OPTIONAL GRAPHIC USER

INTERFACE) .............................................................................................................................. 26

4.2.1

Entering Setup Mode ............................................................................................... 27

4.2.2

Adjusting Settings in Setup Mode ............................................................................ 27

5 TRANSMITTER RF CHANNEL CONFIGURATION SETTINGS ........................................... 30

5.1

FCC/ATEX/IECEx STATEMENTS .................................................................................. 30

5.2

CHANNEL AND FREQUENCY DESIGNATIONS BY COUNT ....................................... 32



September 2015

Page 3 of 34

6 GENERAL TROUBLESHOOTING ......................................................................................... 34

6.1

ASSEMBLY AND REPLACEMENT PARTS ................................................................... 34



September 2015

Page 4 of 34

1 INTRODUCTION

Thank you for your purchase of Magnetek’s XLTX Radio Remote Control.

These instructions are to be used as a reference for personnel operating the XLTX Radio Remote Control and the equipment that this XLTX Radio Remote Control is attached to.

The user of these instructions should have basic knowledge in the handling of electronic equipment.

1.1 PRODUCT MANUAL SAFETY INFORMATION

Magnetek, Inc. (Magnetek) offers a broad range of radio remote control products, control products and adjustable frequency drives, and industrial braking systems for overhead material handling applications.

This manual has been prepared by Magnetek to provide information and recommendations for the installation, use, operation and service of Magnetek’s material handling products and systems (Magnetek

Products). Anyone who uses, operates, maintains, services, installs or owns Magnetek Products should know, understand and follow the instructions and safety recommendations in this manual for Magnetek

Products.

The recommendations in this manual do not take precedence over any of the following requirements relating to cranes, hoists and lifting devices:



Instructions, manuals and safety warnings of the manufacturers of the equipment where the radio system is used,



Plant safety rules and procedures of the employers and the owners of facilities where the

Magnetek Products are being used,



Regulations issued by the Occupational Health and Safety Administration (OSHA),



Applicable local, state or federal codes, ordinances, standards and requirements, or



Safety standards and practices for the overhead material handling industry.

This manual does not include or address the specific instructions and safety warnings of these manufacturers or any of the other requirements listed above. It is the responsibility of the owners, users and operators of the Magnetek Products to know, understand and follow all of these requirements. It is the responsibility of the owner of the Magnetek Products to make its employees aware of all of the above listed requirements and to make certain that all operators are properly trained. No one should use Magnetek

Products prior to becoming familiar with and being trained in these requirements.

WARRANTY INFORMATION

FOR INFORMATION ON MAGNETEK’S PRODUCT WARRANTIES BY PRODUCT TYPE, PLEASE VISIT

WWW.MAGNETEK.COM.



September 2015

Page 5 of 34

Throughout this document WARNING and CAUTION statements have been deliberately placed to highlight items critical to the protection of personnel and equipment.

WARNING – A warning highlights an essential operating or maintenance procedure, practice, etc. which, if not strictly observed, could result in injury or death of personnel, or long term physical hazards. Warnings are highlighted as shown below:

WARNING

CAUTION – A caution highlights an essential operating or maintenance procedure, practice, etc. which, if not strictly observed, could result in damage to, or destruction of equipment, or loss of functional effectiveness. Cautions are highlighted as shown below:

CAUTION

WARNINGS and CAUTIONS SHOULD NEVER BE DISREGARDED.

The safety rules in this section are not intended to replace any rules or regulations of any applicable local, state, or federal governing organizations. Always follow your local lockout and tagout procedure when maintaining any radio equipment. The following information is intended to be used in conjunction with other rules or regulations already in existence. It is important to read all of the safety information contained in this section before installing or operating the Radio Control System.



September 2015

Page 6 of 34

2 CRITICAL INSTALLATION CONSIDERATIONS

WARNING

PRIOR TO INSTALLATION AND OPERATION OF THIS EQUIPMENT, READ AND DEVELOP AN

UNDERSTANDING OF THE CONTENTS OF THIS MANUAL AND THE OPERATION MANUAL OF THE

EQUIPMENT OR DEVICE TO WHICH THIS EQUIPMENT WILL BE INTERFACED. FAILURE TO FOLLOW

THIS WARNING COULD RESULT IN SERIOUS INJURY OR DEATH AND DAMAGE TO EQUIPMENT.

FOLLOW YOUR LOCAL LOCKOUT TAGOUT PROCEDURE BEFORE MAINTAINING ANY REMOTE

CONTROLLED EQUIPMENT. ALWAYS REMOVE ALL ELECTRICAL POWER FROM THE EQUIPMENT

BEFORE ATTEMPTING ANY INSTALLATION PROCEDURES. DE-ENERGIZE AND TAGOUT ALL

SOURCES OF ELECTRICAL POWER BEFORE TOUCH-TESTING ANY EQUIPMENT. FAILURE TO

FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY OR DEATH AND DAMAGE TO

EQUIPMENT.

AFTER INSTALLATION BE SURE TO VERIFY THAT THE TRANSMITTER IS NOT INTERFERING WITH

OTHER EQUIPMENT IN THE AREA. ALSO VERIFY THAT OTHER EQUIPMENT IS NOT INTERFERING

WITH THE TRANSMITTER AND ITS ASSOCIATED EQUIPMENT. FAILURE TO FOLLOW THESE

WARNINGS COULD RESULT IN SERIOUS INJURY OR DEATH AND DAMAGE TO EQUIPMENT.

WARNING

SUBSTITUTION OF COMPONENTS MAY IMPAIR INTRINSIC SAFETY.

2.1 GENERAL

Radio controlled equipment operates in several directions. Quite frequently, the equipment is operated in areas where people are working in close proximity to the equipment. The operator must exercise extreme

caution at all times. Workers must constantly be alert to avoid accidents. The following recommendations have been included to indicate how careful and thoughtful actions may prevent injuries, damage to equipment, or even save a life.

2.2 PERSONS AUTHORIZED TO OPERATE RADIO CONTROLLED EQUIPMENT

Only properly trained persons designated by management should be permitted to operate radio controlled equipment.

Radio controlled equipment should not be operated by any person who cannot read or understand signs, notices and operating instructions that pertain to the equipment.

Radio controlled equipment should not be operated by any person with insufficient eyesight or hearing or by any person who may be suffering from a disorder or illness, is taking any medication that may cause loss of equipment control, or is under the influence of alcohol or drugs.



September 2015

Page 7 of 34

2.3 SAFETY INFORMATION AND RECOMMENDED TRAINING FOR RADIO CONTROLLED

EQUIPMENT OPERATORS

Anyone being trained to operate radio controlled equipment should possess as a minimum the following knowledge and skills before using the radio controlled equipment.

The operator should:

 have knowledge of hazards pertaining to equipment operation

 have knowledge of safety rules for radio controlled equipment

 have the ability to judge distance of moving objects

 know how to properly test prior to operation

 be trained in the safe operation of the radio transmitter as it pertains to the equipment being operated

 have knowledge of the use of equipment warning lights and alarms

 have knowledge of the proper storage space for a radio control transmitter when not in use

 be trained in transferring a radio control transmitter to another person

 be trained how and when to report unsafe or unusual operating conditions

 test the transmitter emergency stop and all warning devices prior to operation; testing should be done on each shift, without a load

 be thoroughly trained and knowledgeable in proper and safe operation of the equipment that utilizes the radio control

 know how to keep the operator and other people clear of hazardous areas

 know and follow the local lockout and tagout procedures when servicing radio controlled equipment

 know and follow all applicable operating and maintenance manuals, safety procedures, regulatory requirements, and industry standards and codes

The operator shall not:

 operate the equipment if the direction of travel or function engaged does not agree with what is indicated on the controller

 operate any damaged or malfunctioning equipment

 change any settings or controls without authorization and proper training

 remove or obscure any warning or safety labels or tags

 leave power on the radio controlled equipment when the equipment is not in operation

 operate any equipment using a damaged controller because the unit may be unsafe

 operate manual motions with other than manual power

 operate radio controlled equipment when low battery indicator is on



September 2015

Page 8 of 34

WARNING

THE OPERATOR SHOULD NOT ATTEMPT TO REPAIR ANY RADIO CONTROLLER. IF ANY PRODUCT

PERFORMANCE OR SAFETY CONCERNS ARE OBSERVED, THE EQUIPMENT SHOULD

IMMEDIATELY BE TAKEN OUT OF SERVICE AND BE REPORTED TO THE SUPERVISOR. DAMAGED

AND INOPERABLE RADIO CONTROLLER EQUIPMENT SHOULD BE RETURNED TO MAGNETEK FOR

EVALUATION AND REPAIR. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS

INJURY OR DEATH AND DAMAGE TO EQUIPMENT

Transmitter switches should never be mechanically blocked ON or OFF. When not in use, the operator should turn the transmitter OFF. A secure storage space should be provided for the transmitter unit, and the transmitter unit should always be placed there when not in use. This precaution will help prevent unauthorized people from operating the material handling equipment.

Spare transmitters should be stored in a secure storage space and only removed from the storage space after the current transmitter in use has been turned OFF, taken out of the service area and secured.

2.5 PRE-OPERATION TEST

At the start of each work shift, or when a new operator takes control of the equipment, operators should do, as a minimum, the following steps before making lifts with any equipment:

Test all warning devices.

Test all functions.

Test the transmitter machine stop.

WARNING

KNOW AND FOLLOW PROPER BATTERY HANDLING, CHARGING AND DISPOSAL PROCEDURES.

IMPROPER BATTERY PROCEDURES CAN CAUSE BATTERIES TO EXPLODE OR DO OTHER

SERIOUS DAMAGE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY OR

DEATH AND DAMAGE TO EQUIPMENT.

Use only batteries approved by Magnetek for the specific product.

Do not dispose of a battery pack in fire; it may explode.

Do not attempt to open the battery pack.

Do not short circuit the battery.

Do not use sharp tools to remove the battery pack or the cells.

Keep the battery pack environment cool during storage (i.e., not in direct sunlight or close to a heating source).



September 2015

Page 9 of 34

2.7 OPTIONAL RECHARGEABLE BATTERY CHARGING

For those transmitters equipped with rechargeable batteries and battery chargers, all users shall be familiar with the instructions of the charger before attempting to use.

Do not attempt to charge non-rechargeable battery packs in the charger.

Avoid charging partially discharged rechargeable batteries to help prolong battery cycle life.

Do not charge batteries in a hazardous environment.

Keep the battery pack environment cool during charging (i.e., not in direct sunlight or close to a heating source).

Do not short the charger.

Do not attempt to charge a damaged battery.

Use only Magnetek approved chargers for the appropriate battery pack.

Do not attempt to use a battery that is leaking, swollen or corroded.

Charger units are not intended for outdoor use. Only use charger units indoors.

Before disposing of batteries consult local and governmental regulatory requirements for proper disposal procedure.



September 2015

Page 10 of 34

WARNING

ALL EQUIPMENT MUST HAVE A MAINLINE CONTACTOR INSTALLED AND ALL TRACKED CRANES,

HOISTS, LIFTING DEVICES AND SIMILAR EQUIPMENT MUST HAVE A BRAKE INSTALLED. FAILURE

TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY OR DEATH AND DAMAGE TO

EQUIPMENT.

AN AUDIBLE AND/OR VISUAL WARNING MEANS MUST BE PROVIDED ON ALL REMOTE

CONTROLLED EQUIPMENT AS REQUIRED BY CODE, REGULATION, OR INDUSTRY STANDARD.

THESE AUDIBLE AND/OR VISUAL WARNING DEVICES MUST MEET ALL GOVERNMENTAL

REQUIREMENTS. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY OR

DEATH AND DAMAGE TO EQUIPMENT.

THE DIRECT OUTPUTS OF THIS PRODUCT ARE NOT DESIGNED TO INTERFACE DIRECTLY TO TWO

STATE SAFETY CRITICAL MAINTAINED FUNCTIONS, I.E., MAGNETS, VACUUM LIFTS, PUMPS,

EMERGENCY EQUIPMENT, ETC. A MECHANICALLY LOCKING INTERMEDIATE RELAY SYSTEM WITH

SEPARATE POWER CONSIDERATIONS MUST BE PROVIDED. FAILURE TO FOLLOW THIS WARNING

COULD RESULT IN SERIOUS INJURY OR DEATH OR DAMAGE TO EQUIPMENT.

Cranes, hoists, lifting devices and other material handling equipment can be large, and operate at high speeds.

The operator should:

 continuously watch and monitor status of lifted loads

 know and follow cable and hook inspection procedures

The operator shall not:

 lift or move more than the rated load

 use the crane, hoist or lifting device to lift, support or transport people

 lift or carry any loads over people

 operate the crane, hoist or lifting device unless all persons, including the operator, are and remain clear of the supported load and any potential pinch points

 operate a crane, hoist or lifting device when the device is not centered over the load

 operate a crane, hoist or lifting device if the chain or wire rope is not seated properly in the sprockets, drum or sheave

 leave any load unattended while lifted



September 2015

Page 11 of 34

2.10 SPECIFIC CONDITIONS OF SAFE USE

WARNING

POTENTIAL ELECTROSTATIC CHARGING HAZARD. SEE INSTRUCTIONS.

The XLTX has a maximum measured capacitance from housing and/or accessory to ground of 10pF. When possible, care should be taken to reduce the potential for generation of static electricity, such as:

 Controlling the work environment humidity level to minimize generation of static electricity

 Protect the transmitter from direct airflow

 Touch the transmitter with an insulating object or glove whenever possible

 Use in conjunction with gas detection monitoring

 Do not use in an area that is known to be a static electricity hazard

Additional information on electrostatics can be found in EN TR50404 and IEC/TR60079-32. Joysticks used in the transmitter may have >10% by mass of aluminum. The bulk of this material will be inside the transmitter and will not be accessible.



September 2015

Page 12 of 34

3 XLTX TRANSMITTER STANDARD CONFIGURATION AND OPERATION

WARNING

BEFORE OPERATING THE TRANSMITTER FAMILIARIZE YOURSELF WITH ALL SAFETY

INFORMATION IN THIS MANUAL, THE CORRESPONDING RECEIVER SYSTEM MANUAL,

APPROPRIATE MANUAL SUPPLEMENTS AND ANY OTHER LOCAL, STATE, OR FEDERAL RULES OR

REGULATIONS ALREADY IN EXISTENCE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN

SERIOUS INJURY OR DEATH AND DAMAGE TO EQUIPMENT.

Figure 1: Typical XLTX with Maximum Number of Paddles and Auxiliary Switches



September 2015

Page 13 of 34

3.1 INSTALLING BATTERY PACK

Prior to utilizing the XLTX transmitter, battery packs must be installed.

3.1.1 Approved Batteries for Intrinsically Safe Operation

The XLTX transmitter has been tested and approved for intrinsically safe operation with the following AA (LR6) size batteries:

Duracell MN1500

Duracell PC1500

Rayovac 815

Use only the above battery manufacturers and part numbers as replacement batteries to maintain intrinsically safe operation.

WARNING

ONLY OPERATE THE TRANSMITTER IN HAZARDOUS ENVIRONMENTS WITH THE APPROVED

BATTERIES. FAILURE TO USE THE APPROVED BATTERIES COULD RESULT IN SERIOUS INJURY

OR DEATH AND DAMAGE TO EQUIPMENT. ONLY USE FOUR BATTERIES OF THE SAME

MANUFACTURER AND MODEL NUMBER.

3.1.2 Intrinsically Safe Alkaline Battery Pack

The Intrinsically Safe XLTX comes standard with an intrinsically safe battery pack that holds four disposable AA alkaline batteries.

Figure 2: Intrinsically Safe Battery Pack (Top and Bottom Views)

To change the alkaline batteries in the battery pack, loosen the T10 star bit screws completely and remove the battery pack lid. Replace all the batteries with new ones.



September 2015

Page 14 of 34

Figure 3: Separated Alkaline Battery Pack

When reinserting the lid onto the outer housing, make sure that the lid aligns with the outer housing and secure all four T10 star bit screws. When placing the battery pack into the XLTX battery pocket, ensure that the pack is fully seated and that the thumb screw is tightened down to hold the battery pack in place.

Figure 4: Installation of Battery Pack into XLTX transmitter

NOTE: The Intrinsically Safe battery pack must be secured in place with the thumb screw.

Failure to secure the thumb screw will not allow the battery pack to stay securely in place.



September 2015

Page 15 of 34

3.1.3 Spare Battery Storage Compartment

The XLTX transmitter features a spare battery compartment to store a second battery pack. The second battery pack allows for quick replacement of the primary battery pack when the battery level gets low.

The spare battery storage compartment is the battery compartment with IR cover inside the battery compartment.

IR Cover is located in spare battery compartment

Compartment without IR cover is the primary battery compartment

Figure 5: Spare Battery Compartment Location

NOTE: The spare battery compartment features battery spring contacts like the primary battery compartment. These spring contacts in the spare battery compartment have no electrical connection and are used to secure the spare battery pack inside the compartment to prevent rattling.

3.2 TURNING THE TRANSMITTER ON AND OFF

The XLTX uses both a three position toggle switch labeled OFF-ON-START and a Machine Stop switch to turn the transmitter on or off.

Figure 6: Machine Stop Switch and OFF-ON-START Toggle



September 2015

Page 16 of 34

3.2.1 Turning On the Transmitter (with Standard Status LED Indicator(s))

3.2.1.1 Transmitters Equipped with Separate Power/Status and Battery LED Indicators

First, the Machine Stop switch must be in the raised position (pulled out). Next, push the OFF-

ON-START toggle switch to the START position and release it once the Power/Status LED lights up as a solid green color. Following the Power/Status LED turning on and illuminating, the unit will perform a routine initialization.

During initialization, the XLTX scans for any switches or motions that may be on during power up.

If any switches or motions are on, the failure will be displayed as a solid red Battery LED, and then the XLTX will power itself down.

After a successful initialization, the XLTX will enter normal operation mode and display the normal operating status LED indications. See Section 3.6 for more information on the normal operation mode with standard status LED.

3.2.1.2 Transmitters Equipped with Single Status/Battery LED Indicator


ON-START toggle switch to the START position and release it immediately. The unit will perform a routine initialization.


If any switches or motions are on, the failure will power the XLTX down.

NOTE: There will be no LED indication of the failure on the Single LED equipped transmitters. If the Battery Status LED does not go into slow blinking mode as detailed in Section 3.6 after 15 seconds, reboot the transmitter by turning the OFF the transmitter and then turning the transmitter back ON.

After a successful initialization, the XLTX will enter normal operation mode and display the normal operating status LED indications. See Section 3.6 for more information on the normal operation mode with standard status LED.

3.2.2 Turning On the Transmitter (with Optional Graphic User Interface Screen)


ON-START toggle switch to the START position and release it once the Magnetek logo appears on the LCD screen. Following the logo screen, the unit will perform a routine initialization.


If any switches or motions are on, the failure will be displayed on the screen, and then the XLTX will power itself down.

After a successful initialization, the XLTX will enter the Normal Operation Mode and display the normal operating screen. See Section 3.7 for more information on the Normal Operation Mode with Optional Graphic User Interface.

NOTE: Holding the OFF-ON-START toggle in the START position for more than 5 seconds will put the device into Setup Mode. For normal use release the START toggle once the Magnetek logo appears. See Section 4.2 for more information on the Setup Mode.



September 2015

Page 17 of 34

3.2.3 Pulling In the Machine Stop Relay

Once the XLTX has been turned on (as described in Section 3.2.1) and in the Normal Operating

Mode, the Machine Stop relay in the receiver can be pulled in by pushing the OFF-ON-START toggle switch to the START position and then releasing.

NOTE: You must release the OFF-ON-START switch to the ON position after the unit is powered up, then push to the START position a second time to pull in the Machine Stop relay.

3.2.4 Turning Off the Transmitter

The transmitter can be turned off by pressing the OFF-ON-START toggle switch down to the OFF position. Once turned off, the Machine Stop relay in the receiver is immediately opened.

NOTE: If the unit has a standard status LED, it will illuminate solid red during the transmitter’s power down process. Once the power down process is complete, the transmitter will turn off and the status LED will not be on.

NOTE: Depressing the Machine Stop switch will also turn the transmitter off and open the

Machine Stop relay in the receiver. See Section 3.3 for more information on the Machine Stop switch.

3.3 MACHINE STOP SWITCH (FOR EMERGENCY STOPPING ONLY)

When the Machine Stop switch is depressed, the Machine Stop relay in the receiver is immediately opened.

Under normal operating conditions, the Machine Stop switch must be in the raised position or the transmitter and system will not operate.

NOTE: The Machine Stop Switch is to be used for emergency stopping only, not for normal system shut down.

3.4 POWER/STATUS AND BATTERY LED

The standard XLTX transmitter includes a Power/Status LED to let the operator know that the unit is functioning and Battery LED to indicate that the battery level is low (see Section 3.6.1 for LED indication definitions).

NOTE: Single Status/Battery LED equipped units will indicate that the transmitter is on and the battery level from the single LED (see Section 3.6.2 for LED indication definitions).

3.5 OPTIONAL GRAPHIC USER INTERFACE

The optional LCD screen located at the center of the device provides visual information during the operation of the XLTX transmitter. It is used to change configuration settings, confirm commands being operated, provide two-way feedback, and display transmitter diagnostic information such as battery life and signal strength.

The optional graphic user interface replaces the standard status LED when ordered.

3.6 NORMAL OPERATING MODE WITH STANDARD STATUS LED(S)

In normal operating mode, the XLTX utilizes the Power/Status and Battery LED(s) to communicate the watch dog timer within the CPU of the transmitter, the machine stop relay status and when the battery level is low.



September 2015

Page 18 of 34

3.6.1 Transmitters Equipped with Separate Power/Status and Battery LED Indicators

3.6.1.1 Watch Dog Indicator (Steady Slow Blinking Green Power/Status LED)

The blinking Power/Status LED represents the watch dog timer within the CPU of the unit. This indicates that the transmitter is powered on.

NOTE: The Power/Status LED should be continuously blinking at all times. If the LED is not blinking the transmitter will need to be rebooted to operate properly.

3.6.1.2 Machine Stop Relay Indicator (Rapidly Green Blinking Power/Status LED)

When the receiver is online with the transmitter and the machine stop relay is successfully pulled in, the Power/Status LED will rapidly blink green.

NOTE: If the receiver inactivity timer times out, the transmitter will revert back to the watch dog indicating status (steady slow blinking Green Power/Status LED). Following the procedure for pulling in the machine stop relay in Section 3.2.3 will resume the rapidly blinking green

Power/Status LED if the machine stop relay is successfully pulled in.

NOTE: This LED function is only available on the 2.4 GHz and 900 MHz equipped transmitters.

On 433 MHz equipped transmitters, the watch dog indicator function in Section 3.6.1.1 continues to operate after the machine stop relay is pulled in.

3.6.1.3 Low Battery Level Indicator (Blinking Red Battery LED)

The Battery LED will rapidly flash red when the battery level drops below 10%. The Power/Status

LED will continue blinking for the watch dog indicator and machine stop relay indicator status.

NOTE: If using an optional battery pack from what the unit was shipped from the factory with, the low battery level indicator will be inaccurate unless the dip switch settings are set to the correct battery type being used. See Section 3.1.3 for details to properly set the dip switches.

3.6.1.4 Shutdown Sequence Initiated Indicator (Solid Red Battery LED)

When the transmitter is turned off or if the machine stop is depressed, the transmitter will begin its shut down sequence. During the sequence, the Red Battery LED will illuminate solid.

NOTE: When the shutdown sequence is completed, all LEDs will turn off.

3.6.2 Transmitters Equipped with Single Status/Battery LED Indicator

NOTE: For specific LED function details, always refer to the transmitter drawings provided with the system.

3.6.2.1 Watch Dog Indicator (Steady Slow Blinking Red Status/Battery LED)

The slow blinking Battery/Status LED represents the watch dog timer within the CPU of the unit.

This indicates that the transmitter is powered on.

NOTE: The Status/Battery LED should be continuously blinking at all times. If the LED is not blinking the transmitter will need to be rebooted to operate properly.

3.6.2.2 Low Battery Level Indicator (Rapidly Blinking Red Status/Battery LED)

The Status/Battery LED will rapidly flash red when the battery level drops below 10%.



September 2015

Page 19 of 34

NOTE: If using an optional battery pack from what the unit was shipped from the factory with, the low battery level indicator will be inaccurate unless the dip switch settings are set to the correct battery type being used. See Section 3.1.3 for details to properly set the dip switches.

3.6.2.3 Shutdown Sequence Initiated Indicator (Solid Red Battery LED)

When the transmitter is turned off or if the machine stop is depressed, the transmitter will begin its shut down sequence. During the sequence, the red Status/Battery LED may illuminate solid.

NOTE: If the shutdown sequence is started when the LED is not illuminated, the LED will stay in the off state during the shutdown process.

NOTE: When the shutdown sequence is completed, all LEDs will turn off.

3.7 NORMAL OPERATING MODE WITH OPTIONAL GRAPHIC USER INTERFACE

In normal operating mode, the XLTX displays real time information relating to the operation of the transmitter on the graphic user interface. Information may include Command Confirmation,

Battery Life, Signal Strength, Two-Way Feedback, etc.

Figure 7: Normal Operating Screen on Graphic User Interface

3.7.1 Watch Dog Indicator (Spinning Arrow)

The spinning arrow represents the watch dog timer within the CPU of the unit.

NOTE: The arrow should be continuously spinning at all times. If the arrow is not spinning, the transmitter will need to be rebooted to operate properly.

Each time the user operates a control on the transmitter, a message will be displayed on the graphic user interface screen confirming what is being operated.

For example, if the second paddle is moved to its 4th position in the UP direction the display will show ‘MTN2 D1 SP=4’. This translates to ‘Motion 2, Direction 1, Speed 4’.

3.7.3 Battery Life Indicator

Remaining battery life is displayed in the bottom left hand corner of the graphic user interface screen.



September 2015

Page 20 of 34

Battery life is displayed in 5% increments.

NOTE: If using a different battery pack than what the unit originally shipped with, the battery life indicator will be inaccurate unless the dip switch settings are set to the correct battery type being used. See Section 3.1.3 for details to properly set the dip switches.

NOTE: The battery display is only shown when the battery is powering the device. When the device is powered through the optional tethered connection the battery indicator is not displayed and a plug icon is display instead.

NOTE: The battery life indictor will only show accurate battery life when using Magnetek approved battery packs.

3.7.4 Signal Strength Indicator

The Signal Strength Indicator shows the radio signal strength at the receiver.

The Signal Strength Indicator is only available in systems equipped for Two-Way feedback

(systems utilizing the 433 MHz frequency band do not have Two-Way feedback available). For such systems, Signal Strength is displayed at the bottom of the graphic user interface screen.

Signal Strength is displayed in 5% increments.

NOTE: On 433 MHz systems, the signal strength indicator will show minimum signal strength regardless of the actual signal strength (systems utilizing the 433 MHz frequency band do not have Two-Way feedback).

3.7.5 Two-Way Feedback System

This option allows the user to view various parameters that may be important to the operation of the equipment on the graphic user interface display screen.

Parameters such as engine RPM, the torque or speed of a drive, temperature, current, or any other useful values can be sent from the receiver and displayed on the transmitter.

NOTE: Systems utilizing the 433 MHz frequency band do NOT have Two-Way feedback available.

3.8 JOYSTICKS AND PADDLES/LEVERS

To activate the desired motor functions, operate the Joystick or Paddle/Lever that corresponds to the desired motion.

To activate higher speed functions for those transmitter models so equipped, operate the Joystick or Paddle/Lever further to activate the desired speed.

3.9 ROTARY SELECTOR SWITCH

The rotary selector switch can be used to select various modes of operation.

A rotary switch can have 2 to 12 positions to select from.

These switches activate special function relays that control items such as grab attachments, magnets, lights, etc.



September 2015

Page 21 of 34

The auxiliary switches can be momentary or latched.

3.11 CONNECTING THE XLTX TO A COMPUTER

WARNING

TO PREVENT IGNITION OF FLAMMABLE OR COMBUSTIBLE ATMOSPHERES, AND TO AVOID

COMPROMISING INTRINSIC SAFETY OF THE EQUIPMENT, READ, UNDERSTAND, AND ADHERE TO

THE LIVE MAINTENANCE PROCEDURES BELOW.

Only trained Magnetek service personnel are permitted to connect the XLTX to a computer.

Contact Magnetek Service if service to the product is required.

WARNING

PROGRAMMING THROUGH THE USB PORT IS TO BE DONE SOLELY BY MAGENETK SERVICE

PERSONNEL. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY OR

DEATH, AND DAMAGE TO EQUIPMENT.



September 2015

Page 22 of 34

The transmitter may have settings changed one of three ways.

For units without the optional graphic user interface, the built-in dip switch block can adjust the

RF channel, RF Channel Setting Override function, and the battery type. The RF channel and access code can be programmed using the IR configuration link with a compatible receiver. All other settings can only be changed at the factory.

For units with the optional graphic user interface, the Setup Mode can be used to edit configuration settings such as: Access Code, Channel Select, User Code, Transmitter Time Out,

Backlight Time Out, Password Enable, Change Password, and more.

NOTE: The IR configuration receiver link can adjust settings on both types of units (with and without the optional graphic user interface), but on units without the optional display the saved channel is only used if the override dip switch is set to ON. If the override dip switch is set to OFF, the dip switch settings set the RF channel.

4.1 TRANSMITTER SETUP SETTINGS WITH STANDARD STATUS LEDS

WARNING

TO PREVENT IGNITION OF FLAMMABLE OR COMBUSTIBLE ATMOSPHERES, AND TO AVOID

COMPROMISING INTRINSIC SAFETY OF THE EQUIPMENT, READ, UNDERSTAND, AND ADHERE TO

THE LIVE MAINTENANCE PROCEDURES BELOW.

There are two settings that can be adjusted using the dip switch block: the RF Channel Setting

Override setting, and the RF Channel setting. In addition, the access code and channel can be changed using the IR configuration receiver link with a compatible receiver (contact the factory to determine if your receiver is compatible).

4.1.1 RF Channel Setting Override

The dip switch block can enable or disable the RF channel setting dip switch override. Dip switch position number 3 enables the channel from memory function, which enables the transmitter to utilize the channel setting that was set up using the IR configuration receiver option. This dip switch is located on the dipswitch block which is visible through the USB/IR window (see Figure

8). To set the RF channel setting override, reference Figure 9 for dip switch settings for the override function.

4.1.2 RF Channel Setting Selection

The dip switch block can also set the RF channel setting. This dip switch block is the same block used for RF channel setting override. The dip switch block is visible through the USB/IR window

(see Figure 9).



September 2015

Page 23 of 34

WARNING

ONLY PERFORM SETTING CHANGES TO THE DIP SWITCH BLOCK THROUGH THE IR PORT IN A

NON-HAZARDOUS ENVIRONMENT OR “SAFE” ZONE. FAILURE TO FOLLOW THIS WARNING COULD

RESULT IN SERIOUS INJURY OR DEATH, AND DAMAGE TO EQUIPMENT.

Figure 8: Dip Switch Blcok as Viewed Through USB/IR Port

NOTE: The dip switch block switches are oriented so that the Off position is next to the number designator and the On position is up or away from the number designator.

Regardless of which radio frequency the transmitter was equipped with the RF channel dip switch settings are the same. Refer to Section 5.2 for details on the specific RF channel details for the radio frequency that the transmitter is equipped with.

The following figure details the dip switch positions for each RF channel.



September 2015

Page 24 of 34

Figure 9: Dip Switch Positions for RF Channel Selection

The dip switch settings will take effect upon the next power cycle of the transmitter.

NOTE: If using the IR configuration receiver function on transmitters NOT equipped with the optional graphic user interface, the channel settings will read from the dip switch positions and not from memory when the channel from memory override function is not enabled. The RF channel set by the IR configuration receiver function will not be used unless the memory override dip switch is set to ON. When the RF channel from memory override is NOT enabled, the dip switch positions set the RF channel used by the transmitter.

NOTE: The transmitters equipped with the optional graphic user interface will read channel settings from memory and will not respond to dip switch changes for the channel setup.

4.1.3 IR Configuration Receiver

The IR Cfg Recv function display allows the transmitter to link to a compatible receiver by using

IR (contact the factory to determine if your receiver is compatible) and automatically set up the channel and access code to match the linked compatible receiver.



September 2015

Page 25 of 34

NOTE: If using the IR configuration receiver function on transmitters NOT equipped with the optional graphic user interface, the channel settings will read from the dip switch positions and not from memory when the channel from memory override function is not enabled. The RF channel set by the IR configuration receiver function will not be used unless the memory override dip switch is set to ON. When the RF channel from memory override is NOT enabled, the dip switch positions set the RF channel used by the transmitter.

4.1.3.1 IR Configuration Receiver On Transmitters Equipped with Separate Power/Status and Battery LED Indicators

To utilize the IR configuration receiver function and link to a compatible receiver, push the OFF-

ON-Start toggle to the Start position and hold for more than 5 seconds. When the transmitter successfully enters the IR configuration mode, the Power/Status and Battery LED(s) will blink alternately continuously. After the LEDs are blinking alternately, point the IR window of the transmitter at the desired receiver to control and momentarily press the OFF-ON-Start toggle to the Start position and release.

If the link is successful, the LEDs will stop blinking and the transmitter will shut down. The new settings obtained from the IR configuration function will take effect upon the next power cycle of the transmitter.

If the link is unsuccessful with a compatible receiver, the Power/Status and Battery LED(s) will continue to blink alternately.

To cancel the IR configuration receiver without a successful link, move the OFF-ON-Start toggle to the OFF position.

4.1.3.2 IR Configuration Receiver On Transmitters Equipped with Single Status/Battery

LED Indicator

To utilize the IR configuration receiver function and link to a compatible receiver, push the OFF-

ON-Start toggle to the Start position and hold for more than 5 seconds. When the transmitter successfully enters the IR configuration mode, the Status/Battery LED will blink continuously.

After the LED is blinking, point the IR window of the transmitter at the desired receiver to control and momentarily press the OFF-ON-Start toggle to the Start position and release.

If the link is successful, the LED will stop blinking and the transmitter will shut down. The new settings obtained from the IR configuration function will take effect upon the next power cycle of the transmitter.

If the link is unsuccessful with a compatible receiver, the Status/Battery LED will continue to blink.

To cancel the IR configuration receiver without a successful link, move the OFF-ON-Start toggle to the OFF position.

4.2 USING THE TRANSMITTER IN SETUP MODE (WITH OPTIONAL GRAPHIC USER

INTERFACE)

NOTE: The Setup Mode is only accessed on transmitters equipped with the optional graphic user interface. The units equipped with the standard status LED can only have the settings of the transmitter changed at the factory.

The Setup Mode can be used to edit configuration settings such as: Access Code, Channel

Select, User Code, Transmitter Time Out, Backlight Time Out, Password Enable, Change

Password, and more.



September 2015

Page 26 of 34

NOTE: No parameter changes will take effect until the user has selected ‘Save and Exit’ from the

Setup Mode.

4.2.1 Entering Setup Mode

To enter the Setup Mode, first make sure the unit is OFF and the Machine Stop switch is raised.

Next, push the OFF-ON-START toggle switch to the START position and hold it in the START position for more than 5 seconds until the setup screen appears.

The user will see a prompt for a four digit password if the password feature is enabled. If no password is enabled, then the adjustments in Section 4.2.2 will be available with no further input required from the user.

NOTE: The password feature is enabled by default from the factory.

Use the Joystick/Paddle to increment/decrement the value and toggle to the START position when finished. If the password is entered correctly, the device will enter Setup Mode. If it is entered incorrectly, the device will power down.

NOTE: The factory default password to get into the setup menu is 0000.

4.2.2 Adjusting Settings in Setup Mode

To navigate through Setup Mode, the Joystick/Paddle designated (MTN 1) and OFF-ON-START switch are used. The Joystick/Paddle cycles through the menus and is also used to change parameters within the menus. Pushing the OFF-ON-START switch to the START position will toggle between the menu and its parameter(s). When adjusting larger values, the speed is dependent on how far the Joystick/Paddle is depressed.

NOTE: No parameter changes will take effect until the user has selected ‘Save and Exit’ from the

Setup Mode.

4.2.2.1 Access Code

The Access Code determines which receiver will be controlled by the transmitter.

The Access Code in the XLTX transmitter must match the receiver Access Code or dip switches.

If the Access Codes settings on the receiver and transmitter do not match, no communication will occur.

The Access Code is a 20-bit binary value with a decimal equivalent of 0 - 1048575. It will be displayed as binary or decimal depending on the application.

4.2.2.2 Channel Select

The Channel Select setting determines the frequency on which the XLTX is operating.

The user can select channels 1 through 32 which correspond to the frequencies in Section 5.2.

4.2.2.3 User Code

The User Code setting is a unique identifier that allows the user to select multiple modes when using the same channel. The receiver can be tuned to only ‘hear’ messages sent from a transmitter with the same user code.



September 2015

Page 27 of 34

4.2.2.4 Transmitter Timeout

This setting controls the amount of time that the transmitter can be inactive before it automatically shuts off. Factory default is 15 minutes, unless your project specific drawing states otherwise.

The Timeout time can be set from 1 to 60 minutes.

When the unit times out, the transmitter will turn off.

Setting Timeout to 0 disables transmitter timeout.

WARNING

DO NOT ASSUME THE POWER IS OFF IN THE RECEIVER BECAUSE THE TRANSMITTER IS TURNED

OFF. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY OR DEATH AND

DAMAGE TO EQUIPMENT.

4.2.2.5 Backlight Timeout

The Backlight timeout setting controls the amount of time that the backlight will stay on after a command is pressed before it automatically shuts off.

Backlight Timeout can be set from 1 to 30 seconds.

Setting Timeout to disable will disable the backlight.

Setting Timeout to “always on” sets the backlight to be on continuously while the transmitter is on and active.

NOTE: Leaving the backlight on longer will decrease the battery run time and will require more frequent battery replacement (or recharges for optional rechargeable battery packs).

4.2.2.6 Password Enable

This setting enables or disables the requirement of entering a password into the transmitter to enter setup mode.

When the disabled setting is selected the user will go directly into setup mode without being prompted to enter a password.

Magnetek strongly recommends enabling the setup mode password setting to prevent unauthorized or accidental changes to parameters.

NOTE: The unit is shipped with the password requirement enabled and utilizing the factory default password.

4.2.2.7 Change Password

This allows the user to change the password needed to enter the setup mode.

The password must consist of 4 digits.



September 2015

Page 28 of 34

4.2.2.8 IR Configuration Receiver

IR Cfg Recv function in the setup allows the transmitter to link to a compatible receiver by using

IR (contact the factory to determine if your receiver is compatible) and automatically set up the channel and access code to match the linked compatible receiver.

After selecting this option, point the IR window of the transmitter at the desired receiver to control and momentarily press the OFF-ON-Start toggle to the Start position and release. The graphic user interface will display “Attempting” while scanning for the receiver’s IR signal. If the receiver is in range and IR link is made, the message will change to “Success”.

NOTE: The changes to the transmitter’s channel configuration and access code will not be saved until the operator selects the Exit with Save option to exit the Setup Mode.

If the receiver is not in range, the scan will time out and the graphic user interface will display

“Failed”. The operator can reposition the transmitter and reattempt to establish the IR link with the receiver by toggling the Start position on the OFF-ON-Start toggle multiple times.

NOTE: The access code and channel will not be updated to match the desired receiver until

“Success” is displayed. Once “Success” is displayed, subsequent “Failed” messages will not overwrite the access code and channel obtained in the successful IR link until a new successful

IR link is made.

The IR configuration function will only update channel and access code information if the receiver and transmitter are programed at the factory with the same project identification number. If the receiver/transmitter pairing is not programmed with the same project identification number, the graphic user interface will display “Err Project ID” when an IR link is attempted. The IR link will not be successful and the access code and channel information in the transmitter will not be changed.

If the receiver and transmitter IR pair is not operating in the same frequency band when an IR link is attempted, the graphic user interface will display “Err RF Freq”. The IR link will not be successful and the access code and channel information in the transmitter will not be changed.

4.2.2.9 Exit Without Save

If the user does not wish to save any of the configuration changes made, the Exit Without Save option can be selected.

NOTE: None of the changes will be saved upon selection of this option. The transmitter will start up with the last saved configuration settings.

4.2.2.10 Exit With Save

Selection of this option saves all changes and exits the Setup Mode.

Upon exit, the device will start up with the new configuration settings.



September 2015

Page 29 of 34

5 TRANSMITTER RF CHANNEL CONFIGURATION SETTINGS

The RF channel can be set via the dip switch block. Section 5.2 shows the channels and protocols available for each transmitter radio frequency option.

Compliance Statement (Part 15.19)

This device complies with Part 15 of FCC rules.

Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesired operation.

Warning (Part 15.21)

Changes or modifications not expressly approved by the party responsible for compliance should void the user’s authority to operate the equipment.

This portable transmitter with its antenna complies with FCC’s RF exposure limits for general population/uncontrolled exposure.

See “Enrange XLTX/MLTX2 Transmitter ATEX/IECEx Information” sheet, Magnetek PN 198-

80202-0003, for details regarding the hazardous location approvals for this product.



September 2015

Page 30 of 34



September 2015

Page 31 of 34

5.2 CHANNEL AND FREQUENCY DESIGNATIONS BY COUNT

433 MHz

Channel Channel Actual

900 MHz

Channel Channel

01) 01

02) 02

03) 03

04) 04

05) 05

06) 06

07) 07

08) 08

09) 09

10) 10

11) 11

12) 12

13) 13

14) 14

15) 15

16) 16

17) 17

18) 18

19) 19

20) 20

21) 21

22) 22

23) 23

24) 24

25) 25

26) 26

27) 27

28) 28

29) 29

30) 30

31) 31

32) 32

01) 1

02) 2

03) 3

04) 4

05) 5

06) 6

07) 7

08) 8

09) A

10) B

11) C

12) D

13) E

14) F

15) G

16) H

17) I

18) J

19) K

20) L

21) M

22) N

23) O

24) P

25) Q

26) R

27) S

28) T

29) U

30) V

31) W

32) X

Actual

906.30 MHz

907.80 MHz

909.30 MHz

912.30 MHz

915.30 MHz

919.80 MHz

921.30 MHz

902.30 MHz

904.10 MHz

904.30 MHz

905.10 MHz

905.50 MHz

905.70 MHz

906.60 MHz

908.70 MHz

908.90 MHz

909.10 MHz

910.10 MHz

910.70 MHz

911.00 MHz

911.20 MHz

912.00 MHz

914.20 MHz

914.40 MHz

914.60 MHz

914.80 MHz

915.80 MHz

917.40 MHz

923.20 MHz

927.00 MHz

927.30 MHz



September 2015

Page 32 of 34

433 MHZ TELEMOTIVE LEGACY CHANNEL SET: TMS AND TDMA

Channel Channel Actual

01) AK01

02) AK02

03) AK03

04) AK04

05) AK05

06) AK06

07) AK07

08) AK08

09) AK09

10) AK10

11) AK11

12) AK12

13) AK13

14) AK14

15) AK15

16) AK16

17) AK17

18) AK18

19) AK19

20) AK20

21) AKA00 433.125

22) AKA01 433.325

23) AKA02 433.525

24) AKA03 433.725

25) AKA04 433.925

26) AKA05 434.125

27) AKA06 434.325

28) AKA07 434.525

29) AKA08 434.725

30) AK38

31) AK50

Table 2



September 2015

Page 33 of 34

Suggestions

Transmitter will not turn on

Batteries are dead or installed backwards; battery holder is damaged.

Replace the batteries and confirm they are installed according to the polarity marking in the battery pack. Inspect all battery pack contacts for damage. When installing the battery pack into the XLTX, confirm it is installed with the label facing out. Confirm battery pack is installed in the primary battery compartment and not in the spare compartment.

Transmitter is failing switch scan

Be sure all switches and motions are in the off position on startup. See Section 3.2 for more info.

Transmitter Machine Stop

Switch is down or pressed

Be sure the Machine Stop switch is pulled up.

Incorrect system RF channel

Make sure the transmitter and receiver unit are both set to the same RF channel.

Incorrect system access code

Make sure the transmitter and receiver both have the same access code.

Transmitter will not communicate with the receiver

System out of range

Make sure that the startup procedure is initiated within 300 feet from the receiver location. If equipped with the Signal Strength

Indicator, make sure the level is greater than

0%.

The antenna on the receiver is

Inspect the antenna on the receiver for damage and try to locate the antenna in a location that missing, damaged, or is visible when operating the equipment at all improperly installed. times.

6.1 ASSEMBLY AND REPLACEMENT PARTS

If your transmitter ever needs repair, we always recommend that you have Magnetek perform the repair. If you need to refer to a parts list, refer to the transmitter drawing that was included in the shipment of your transmitter. Please contact Magnetek’s service department at 1.866.MAG.SERV for information regarding parts and service.



September 2015

Page 34 of 34

Enrange XLTX Transmitter-Hazardous Locations Manual 198-80202-1001

Enrange XLTX Transmitter

(Intrinsically Safe)

Radio Remote Control

TABLE OF CONTENTS

Suggestions

Transmitter will not turn on

Transmitter will not communicate with the receiver

Related manuals

Table of contents

Enrange XLTX Transmitter-Hazardous Locations Manual 198-80202-1001

Enrange XLTX Transmitter

(Intrinsically Safe)

Radio Remote Control

TABLE OF CONTENTS

Suggestions

Transmitter will not turn on

Transmitter will not communicate with the receiver

Related manuals

Magnetek

Enrange XLTX

Magnetek

XLTX Transmitter-Hazardous Locations

Magnetek

Enrange XLTX

Magnetek

MLTX2 Transmitter-Hazardous Location

Magnetek

Flex 12EX System

Table of contents