- Computers & electronics
- Computer components
- Chassis components
- Mounting kits
- Metra Electronics
- 99-5700
- Installation Guide
Metra Electronics 99-5700 Installation Instructions Manual
Add to My manuals12 Pages
Metra Electronics 99-5700 is a car radio installation kit designed to provide a seamless and secure fit for aftermarket head units in various Ford, Jeep, Lincoln, Mazda, and Mercury vehicles. It offers flexible mounting options to accommodate both 2-Shaft and DIN/ISO DIN head units. The kit includes a faceplate, radio housings, brackets, and necessary hardware for a hassle-free installation. Whether you're upgrading to a modern infotainment system or replacing a faulty factory unit, this kit ensures compatibility and a clean, professional-looking finish.
advertisement
3c
Fig. A
Fig. B
AEROSTAR 1992-97, BRONCO II 1989-90, EXPLORER 1991-94, RANGER 1989-94,
CROWN VICTORIA 1991-94, GRAND MARQUIS 1991-94, ECONOLINE 1992-96, ESCORT
1991-96, TRACER (sedan) 1991-96, F-SERIES PICKUP 1992-96, BRONCO 1992-96,
TAURUS 1990-95, SABLE 1990-95, TEMPO 1989-94, TOPAZ 1989-94, THUNDERBIRD
1989-97, COUGAR 1989-97, CONTINENTAL 1988-94, MARK VII 1990-92, TOWN CAR
1990-94, MARK VIII 1993-95, ASPIRE, B-SERIES PICKUP, CONTOUR, MYSTIQUE,
MUSTANG, PROBE, WINDSTAR, MPV, MX3, MX6, PROTEGE, 626, CAPRI XR2,
VILLAGER, QUEST: For DIN units, using the scored lines on the back of the Faceplate as a guide, cut and remove the shaft supports and mounting clips. Slide the DIN cage into the dash
(through the Faceplate) and secure by bending the metal locking tabs down. Slide the aftermarket head unit into the cage until secure. (see Fig. A). For 2-Shaft units, make wiring connections and slide the aftermarket unit into the dash. Slide the Shaft Supports over the radio shafts and position them along the inner lip of the radio opening. Place the aftermarket faceplate against the outer lip of the radio opening and secure with shaft nuts. (see Fig. B)
4 5
A
C
B
D
(Taurus / Sable application shown)
A) Strip wire ends back ½"
B) Twist ends together
C) Solder
D) Tape
22
Locate the factory wiring harness in the dash. Metra recommends using the proper mating adaptor and making connections as shown. (Isolate and individually tape off the ends of any unused wires to prevent electrical short circuit).
Re-connect the battery terminal and test the unit for proper operation. Mount the head unit/kit assembly to the sub-dash with those screws previously removed.
rev. 130103
INST 5700
KIT COMPONENTS
Radio Housing #1
Radio Housing #2
Faceplate
99-5700
AT-509FD
AW-509FD
DW-5510
INSTALLATION
INSTRUCTIONS
Bracket Set #1
(Econoline)
Bracket #2
(Escort/Lynx)
Shaft
Spacer Set #1
Supports
Snap Spacers
ISO-DIN
Brackets
(4) #8 x ¾" Phillips
Pan-head Screws
(2) #6 Self-tapping Screws
TOOLS REQUIRED
APPLICATIONS
FORD/JEEP/LINCOLN/MAZDA/MERCURY 1975-00
(SEE INSIDE FOR SPECIFIC APPLICATIONS)
Phillips screwdriver
Cutting tool
86-5618 - Head unit removal keys
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2001 METRA ELECTRONICS CORPORATION
TABLE OF CONTENTS
CAR PAGE
FORD
Aerostar 1992-97........................ 1
CAR PAGE
MERCURY (cont.)
Cougar 1989-97..................... 12
Aerostar 1985-91........................ 1
Aspire 1994-97............................2
Bronco 1992-96.......................... 8
Bronco (full) 1987-91................. 3
Bronco 1980-86.......................... 2
Bronco II 1989-90....................... 3
Bronco II 1985-88....................... 4
Contour 1995-00.........................4
Crown Victoria 1992-94.............. 5
Crown Victoria 1979-90............. 5
Cougar 1983-88..................... 12
Grand Marquis 1991-94........ 5
Grand Marquis 1979-90........ 5
Lynx 1985-87.......................... 7
Mystique 1995-009................... 4
Marquis 1979-81.................... 5
Sable 1990-95........................ 9
Sable 1986-89........................ 10
Topaz 1989-94........................ 11
Topaz 1985-88........................ 11
Econoline 1992-96..................... 6
Econoline 1975-91..................... 6
Escort 1991-96............................7
Escort 1985-90............................7
Explorer 1991-94........................ 3
F-Series Pickup 1992-96.......... 8
F-Series Pickup 1987-91.......... 3
F-Series Pickup 1980-86.......... 2
Festiva 1988-93.......................... 8
LTD 1980-91................................ 5
Mustang 1994-00....................... 9
Probe 1993-97............................ 9
Ranger (mini) 1989-94.............. 3
Ranger (mini) 1983-88.............. 4
Taurus 1990-95...........................10
Taurus 1986-89...........................10
Tempo 1989-94...........................11
Tempo 1985-88...........................11
Thunderbird 1989-97................. 12
Tracer 1991-96....................... 7
Tracer (hatch) 19869-90......... 20
Villager 1993-95......................20
NISSAN
Quest 1993-95........................ 20
ADDITIONAL VEHICLES:
ACURA
Integra 1986-89...................... 22
Legend 1986-89..................... 22
ALFA ROMEO
Milano 1980-89....................... 22
Spider Veloce 1987-93..........22
164 L/S 1991-93.................... 22
AUDI
80/90 1988-96........................ 22
100/200 1989-95.................... 22
4000 1980-87..........................22
5000 1978-88......................... 22
S4 1992-93..............................22
BMW
3-Series 1977-98.................... 22
5-Series 1975-96.................... 22
Thunderbird 1983-88................. 12
Windstar 1995-98....................... 13
JEEP
Cherokee 1984-96..................... 13
Cherokee 1996........................... 14
Commanche 1985-92................13
Grand Wagoneer 1987-95........14
Wagoneer 1984-96.................... 13
Wrangler 1984-96.......................15
LINCOLN
Continental 1988-94................... 15
Continental 1985-87................... 16
Mark VII 1990-92........................ 15
Mark VII 1984-89........................ 16
Mark VIII 1993-95....................... 17
6-Series 1977-89.................... 22
7-Series 1978-98.................... 22
8-Series 19901-93.................... 22
DAIHATSU
Charade 1989-92................... 22
DODGE
Colt 1993-94............................22
D50 Pickup 1988-93.............. 22
EAGLE
Summit 1993-94..................... 22
FIAT
Beretpme X19 1985-88........ 22
Town Car 1990-974..................... 15 Brava 1979-83........................ 22
Town Car 1984-89..................... 17
MAZDA
B-Series Pickup 1994................ 3
626 1993-00................................ 18
MPV 1996-99.............................. 18
MX3 1992-96.............................. 18
MX6 1993-97.............................. 18
Navajo 1991-94.......................... 3
Spider 1970-83....................... 22
Strada 1977-83....................... 22
X19 1979-89........................... 22
GEO
Metro 1989-91........................ 22
Tracker 1989-91..................... 22
HONDA
Accord 1982-89...................... 22
Protege 1995-00......................... 19
MERCURY
Capri XR2 1991-94................... 19
CRX 1984-91.......................... 22
Civic 1982-95........................ 22
Del Sol 1993-97..................
22
Prelude 1983-97................... 22
CAR PAGE
JAGUAR
XJ6 19868-93....................... 22
LANCIA
Beta 1979-81...................... 22
MASERATI
Spyder 1985-90..................22
MERCEDES
240/280/300/380/420/450
500SLC/SEL 1970-96....... 22
MITSUBISHI
Mighty Max 1987-96......... 22
Mirage 1993-02.................. 22
PEUGEOT
405 1989-91........................22
505 1984-913........................ 22
PONTIAC
LeMans 1988-93................ 22
PORSCHE
911 1973-99........................22
924 1977-82........................22
924S 1986-88..................... 22
928 1980-96........................22
944 1983-93........................22
968 1992-96........................22
Boxter 1997-2001............... 24
RENAULT
Alliance 19824-85 ................ 22
Encore 1984-87..................22
Fuego 1982-85................... 22
LeCar 1973-83................... 22
18i 1979-83......................... 22
SAAB
900 1979-98........................22
9000 1986-986..................... 22
STERLING
825 1987-88........................22
827 19889-92........................ 22
SUZUKI
Samurai 1988½-93............ 22
Sidekick 1989-91................22
Swift 1989-91...................... 22
X-90 1996-99...................... 22
VOLKSWAGEN
Bus 1968-79....................... 22
Cabriolet 1985-93...............22
Cabro 1995-01.................... 22
Corrado 1990-93................ 22
Dasher 1976-81................. 22
Fox 1987-93........................22
Golf 1985-00....................... 22
Passat 1990-979................. 22
Pickup 1980........................ 22
Rabbit 1975-84................... 22
Scirocco 1981-87............... 22
Super Beetle 1973-79....... 22
Quantum 1982-88..............22
Vanwagon 1980-92........... 22
ALL VEHICLES
3a
Fig. A
Fig. B
AEROSTAR 1985-91, BRONCO 1987-91,
BRONCO II 1985-88, CROWN VICTORIA
1979-90, ECONOLINE 1975-91, ESCORT
1985-90, F-SERIES PICKUP 1987-91, LTD
Fig. C
1979-84, RANGER 1985-88, TAURUS 1986-
89, THUNDERBIRD 1985-88, CONTINENTAL 1985-87, MARK VII 1984-89, TOWN CAR
1984-89, COUGAR 1985-88, GRAND MARQUIS 1979-90, LYNX 1985-90, MARQUIS 1979-
90, SABLE 1986-89, TRACER (hatchback) 1988-90, all JEEPS: For 2-Shaft units, snap the
Faceplate into Radio Housing #2. Slide the aftermarket head unit into the kit and secure with shaft nuts. (see Fig. A). For DIN units, slide the DIN cage into Radio Housing #2 and secure by bending the metal locking tabs down. (The Snap Spacers may be added for a semirecessed installation). Slide the aftermarket head unit into the cage until secure. (see Fig. B).
For ISO-DIN units, cut and remove the shaft supports from the Faceplate. Snap the Faceplate into Radio Housing #2 and slide the head unit into the back of the kit. Attach the ISO-DIN
Brackets to the Housing legs, align the Bracket holes with the unit holes and secure the
Brackets with (2) #6 Self-tapping Screws. (see Fig. C)
3b
Fig. A
Fig. B
BRONCO 1980-86, F-SERIES PICKUP 1980-86, FESTIVA 1988-93, TEMPO 1985-88,
TOPAZ 1985-88: For 2-Shaft units, slide the aftermarket head unit into Radio Housing #1 and secure with shaft nuts. (see Fig. A). For Din units, cut and remove the shaft supports from
Radio Housing #1. Slide the DIN cage into the Housing and secure by bending the metal locking tabs down. Slide the aftermarket head unit into the cage until secure. (see Fig. B)
21
1
MERCURY Tracer (hatchback) 1989-90
2 1
FORD Aerostar 1992-97
2
Disconnect the negative battery terminal to prevent an accidental short circuit. Remove
(3) Phillips screws from the top of the dash trim bezel. Remove the ashtray and (2)
Phillips screws from the bottom of the bezel.
Remove (4) Phillips screws securing the factory head unit and disconnect the wiring.
Cut and remove the shaft supports from the
Faceplate. Skip to step #3c in the
Installation Instructions for ALL VEHICLES on Page #22.
1
MERCURY Villager 1993-96 / NISSAN Quest 1993-95
2
Disconnect the negative battery terminal to prevent an accidental short circuit. Remove
(2) screws from the steering column trim panel and (2) screws from the ashtray cavity.
Unclip the dash trim bezel. Using Metra's
86-5618, pull the factory head unit from the dash and disconnect the wiring.
Cut and remove the shaft supports from the
Faceplate. Skip to step #3c in the
Installation Instructions for ALL VEHICLES on Page #22.
1
FORD Aerostar 1985-91
2
"D"
20
Disconnect the negative battery terminal to prevent an accidental short circuit. Remove
(1) screw above the climate controls. Unclip the dash trim bezel. Using Metra's 86-5618, pull the factory head unit from the dash and disconnect the wiring.
Cut and remove the shaft supports from the
Faceplate. Skip to step #3c in the
Installation Instructions for ALL VEHICLES on Page #22.
"F"
Disconnect the negative battery terminal to prevent an accidental short circuit. Remove
(2) Phillips screws from the base of the dash trim bezel. Pry down on the (2) tabs located at the top of the dash trim bezel and remove the bezel. Remove (4) screws securing the factory head unit and disconnect the wiring.
Cut and remove all mounting tabs on Radio
Housing #2 EXCEPT tabs "D" and "F".
The mounting tabs can be identified by the stamped letter on the back of each tab.
Locate Spacer Set #1. (The Spacers must be placed behind the mounting tabs during installation in step #5). Skip to the
Installation Instructions for ALL VEHICLES on Page #21.
1
1
FORD Aspire 1994-97
2 1
MAZDA Protege 1995-00
2
Disconnect the negative battery terminal to prevent an accidental short circuit. Using
Metra's 86-5618, pull the factory head unit from the dash and disconnect the wiring.
Cut and remove the shaft supports from the
Faceplate. Skip to step #3c in the
Installation Instructions for ALL VEHICLES on Page #22.
1
FORD Bronco / Pickup 1980-86
2
"B"
Disconnect the negative battery terminal to prevent an accidental short circuit. Remove the ashtray and (2) screws from the ashtray cavity. Using Metra's 86-5618, pull the factory head unit from the dash and disconnect the wiring.
Cut and remove the shaft supports from the
Faceplate. Skip to step #3c in the
Installation Instructions for ALL VEHICLES on Page #22.
1
MERCURY Capri XR2 1991-94
2
"B"
2
Disconnect the negative battery terminal to prevent an accidental short circuit. Remove
(2) screws from the top edge of the dash trim bezel. Pull out on the top of the bezel, unhook the base and remove the bezel. If a factory head unit is NOT present, scribe the
(4) mounting holes and radio opening onto the bezel. Drill the holes, cut the opening and place (4) U-clips over the mounting positions.
Cut and remove all mounting tabs on Radio
Housing #1 EXCEPT tabs "B". The mounting tabs can be identified by the stamped letter on the back of each tab. Skip
to the Installation Instructions for ALL
VEHICLES on Page #21.
Disconnect the negative battery terminal to prevent an accidental short circuit. Using
Metra's 86-5618, pull the factory head unit from the dash and disconnect the wiring.
Cut and remove the shaft supports from the
Faceplate. Skip to step #3c in the
Installation Instructions for ALL VEHICLES on Page #22.
19
1
MAZDA MPV 1996-99
2 1
FORD Bronco (full size) / F-Series Pickup 1987-91
2
"D"
Disconnect the negative battery terminal to prevent an accidental short circuit. Unsnap the side trim pieces from the factory head unit. Using Metra's 86-5618, pull the unit from the dash and disconnect the wiring.
1
Cut and remove the shaft supports from the
Faceplate. Skip to step #3c in the
Installation Instructions for ALL VEHICLES on Page #22.
MAZDA MX3 1992-96
2
"F"
Disconnect the negative battery terminal to prevent an accidental short circuit. Carefully pull and remove the dash trim bezel.
Remove (4) screws securing the factory head unit and disconnect the wiring.
Cut and remove all mounting tabs on Radio
Housing #2 EXCEPT tabs "D" and "F".
The mounting tabs can be identified by the stamped letter on the back of each tab.
Locate Spacer Set #1. (The Spacers must be placed behind the mounting tabs during installation in step #5). Skip to the
Installation Instructions for ALL VEHICLES on Page #21.
1
FORD Bronco II 1989-90 / Explorer 1991-94 / Ranger 1989-94
MAZDA Navajo 1991-94 / B-Series Pickup 1994
2
Disconnect the negative battery terminal to prevent an accidental short circuit. Using
Metra's 86-5618, pull the factory head unit from the dash and disconnect the wiring.
Cut and remove the shaft supports from the
Faceplate. Skip to step #3c in the
Installation Instructions for ALL VEHICLES on Page #22.
MAZDA MX6 1993-97 / 626 1993-00
1 2
Disconnect the negative battery terminal to prevent an accidental short circuit. Using
Metra's 86-5618, pull the factory head unit
18
from the dash and disconnect the wiring.
Cut and remove the shaft supports from the
Faceplate. Skip to step #3c in the
Installation Instructions for ALL VEHICLES on Page #22.
Disconnect the negative battery terminal to prevent an accidental short circuit. Remove the ashtray and (2) screws exposed in the ashtray cavity. Using Metra's 86-5618, pull the factory head unit from the dash and disconnect the wiring.
Cut and remove the shaft supports from the
Faceplate. Skip to step #3c in the
Installation Instructions for ALL VEHICLES on Page #22.
3
1
FORD Bronco II / Ranger 1985-88
2
"D"
1
LINCOLN Mark VIII 1993-95
2
"F"
Disconnect the negative battery terminal to prevent an accidental short circuit. Remove
(4) Phillips screws from the top edge of the dash trim bezel. Remove the light switch knob, cigarette lighter and ashtray. Unsnap the molding located below the dash trim bezel and remove (4) screws exposed.
Remove (4) screws securing the factory head unit and disconnect the wiring.
Cut and remove all mounting tabs on Radio
Housing #2 EXCEPT tabs "D" and "F".
The mounting tabs can be identified by the stamped letter on the back of each tab.
Locate Spacer Set #1. (The Spacers must be placed behind the mounting tabs during installation in step #5). Skip to the
Installation Instructions for ALL VEHICLES on Page #21.
FORD Contour 1995-00 / MERCURY Mystique 1995-99
1 2
Disconnect the negative battery terminal to prevent an accidental short circuit. Using
Metra's 86-5618, pull the factory head unit from the dash and disconnect the wiring.
Cut and remove the shaft supports from the
Faceplate. Skip to step #3c in the
Installation Instructions for ALL VEHICLES on Page #22.
1
LINCOLN Town Car 1984-89
2
"D"
4
Disconnect the negative battery terminal to prevent an accidental short circuit. Using
Metra's 86-5618, pull the factory head unit from the dash and disconnect the wiring.
Cut and remove the shaft supports from the
Faceplate. Skip to step #3c in the
Installation Instructions for ALL VEHICLES on Page #22.
"F"
Disconnect the negative battery terminal to prevent an accidental short circuit. Remove
(3) #8 Phillips screws from the bottom of the radio trim bezel. Unsnap the plastic strip located above the bezel and remove (3)
Phillips screws exposed. Gently pull the instrument cluster trim bezel away from the dash and remove the radio trim bezel.
Remove (3) hex-head screws securing the factory head unit and disconnect the wiring.
Cut and remove all mounting tabs on Radio
Housing #2 EXCEPT tabs "D" and "F".
The mounting tabs can be identified by the stamped letter on the back of each tab.
Locate Spacer Set #1. (The Spacers must be placed behind the mounting tabs during installation in step #5). Skip to the
Installation Instructions for ALL VEHICLES on Page #21.
17
1
LINCOLN Continental 1985-87
2
"D"
1
FORD Crown Victoria 1991-94
MERCURY Grand Marquis 1991-94
2
"F"
Disconnect the negative battery terminal to prevent an accidental short circuit. Remove
(2) #8 Phillips screws below the radio opening. Open the ashtray and remove (2)
#8 Phillips screws exposed (it is NOT necessary to remove the center screw).
Unclip and remove the dash trim bezel.
Remove (4) hex-head screws securing the factory head unit and disconnect the wiring.
Cut and remove all mounting tabs on Radio
Housing #2 EXCEPT tabs "D" and "F".
The mounting tabs can be identified by the stamped letter on the back of each tab.
Locate Spacer Set #1. (The Spacers must be placed behind the mounting tabs during installation in step #5). Skip to the
Installation Instructions for ALL VEHICLES on Page #21.
1
LINCOLN Mark VII 1984-89
2
"D"
Disconnect the negative battery terminal to prevent an accidental short circuit. Using
Metra's 86-5618, pull the factory head unit from the dash and disconnect the wiring.
Cut and remove the shaft supports from the
Faceplate. Skip to step #3c in the
Installation Instructions for ALL VEHICLES on Page #22.
1
FORD Crown Victoria / LTD 1979-90
MERCURY Grand Marquis / Marquis 1979-90
2
"D"
"F"
16
Disconnect the negative battery terminal to prevent an accidental short circuit. Gently pry out on the dash trim bezel and remove.
Remove (4) 5mm hex-head sheet metal screws securing the factory head unit and disconnect the wiring.
Cut and remove all mounting tabs on Radio
Housing #2 EXCEPT tabs "D" and "F".
The mounting tabs can be identified by the stamped letter on the back of each tab.
Locate Spacer Set #1. (The Spacers must be placed behind the mounting tabs during installation in step #5). Skip to the
Installation Instructions for ALL VEHICLES on Page #21.
"F"
Disconnect the negative battery terminal to prevent an accidental short circuit. Open the ashtray and remove (2) Phillips screws securing the dash trim bezel. Remove (4) screws securing the factory head unit and disconnect the wiring.
Cut and remove all mounting tabs on Radio
Housing #2 EXCEPT tabs "D" and "F".
The mounting tabs can be identified by the stamped letter on the back of each tab.
Locate Spacer Set #1. (The Spacers must be placed behind the mounting tabs during installation in step #5). Skip to the
Installation Instructions for ALL VEHICLES on Page #21.
5
1
FORD Econoline 1992-96
2
1
JEEP Wrangler 1986-96
2
"B"
Disconnect the negative battery terminal to prevent an accidental short circuit. Remove the light switch knob and unscrew the surrounding trim. Remove the cupholder and the screws exposed in the cupholder cavity. Unsnap the (2) trim bezel inserts and remove the screws exposed. Remove the lower steering column trim panel and unclip the dash trim bezel. Using Metra's 86-5618, pull the factory head unit from the dash and disconnect the wiring.
Cut and remove the shaft supports from the
Faceplate. Skip to step #3c in the
Installation Instructions for ALL VEHICLES on Page #22.
FORD Econoline 1975-91
1 2
Disconnect the negative battery terminal to prevent an accidental short circuit. Remove
(6) Phillips screws from the face of the dash trim bezel. Remove the bezel. Remove (2) screws securing the factory head unit and disconnect the wiring.
Cut and remove all mounting tabs on Radio
Housing #2 EXCEPT tabs "B". The mounting tabs can be identified by the stamped letter on the back of each tab. Skip
to the Installation Instructions for ALL
VEHICLES on Page #21.
1
LINCOLN Continental 1988-94 / Mark VII 1990-92
Town Car 1990-94
2
6
Disconnect the negative battery terminal to prevent an accidental short circuit. Remove
(3) screws from the lower edge of the dash trim bezel. Remove (2) screws above the radio opening. Unsnap the right corner of the dash trim bezel, disconnect the cigarette lighter wiring and remove the bezel.
Remove the screws securing the factory head unit and disconnect the wiring.
Cut and remove all mounting tabs on Radio
Housing #2. The mounting tabs can be identified by the stamped letter on the back of each tab. Slide Bracket Set #1 into the slots on the sides of the Housing. Skip to the
Installation Instructions for ALL VEHICLES on Page #21.
Disconnect the negative battery terminal to prevent an accidental short circuit. Using
Metra's 86-5618, pull the factory head unit from the dash and disconnect the wiring.
Cut and remove the shaft supports from the
Faceplate. Skip to step #3c in the
Installation Instructions for ALL VEHICLES on Page #22.
15
1
JEEP Cherokee 1996
2
"E"
1
FORD Escort / MERCURY Tracer 1991-96
2
Disconnect the negative battery terminal to prevent an accidental short circuit. Remove
(3) torx-head screws from the steering column trim panels. Unscrew the tilt steering lever and unsnap the trim panels.
Remove (4) screws from the dash trim bezel and remove the bezel. Remove (2) screws securing the factory head unit and disconnect the wiring.
Cut and remove all mounting tabs on Radio
Housing #2 EXCEPT tabs "E". The mounting tabs can be identified by the stamped letter on the back of each tab. Skip
to the Installation Instructions for ALL
VEHICLES on Page #21.
1
JEEP Grand Wagoneer 1987-95
2
"E"
Disconnect the negative battery terminal to prevent an accidental short circuit. Using
Metra's 86-5618, pull the factory head unit from the dash and disconnect the wiring.
Cut and remove the shaft supports from the
Faceplate. Skip to step #3c in the
Installation Instructions for ALL VEHICLES on Page #22.
1
FORD Escort / MERCURY Lynx 1985-90
2
"B"
14
Disconnect the negative battery terminal to prevent an accidental short circuit. Gently unclip the dash trim bezel. Remove (2) screws securing the factory head unit and disconnect the wiring.
Cut and remove all mounting tabs on Radio
Housing #2 EXCEPT tabs "E". The mounting tabs can be identified by the stamped letter on the back of each tab. Skip
to the Installation Instructions for ALL
VEHICLES on Page #21.
Disconnect the negative battery terminal to prevent an accidental short circuit. Remove
(4) screws from the top edge of the dash trim bezel. Remove (2) screws from the bottom edge of the dash trim bezel. Remove the climate control knobs and remove the bezel.
Remove (4) hex-head screws securing the factory head unit and disconnect the wiring.
Cut and remove all mounting tabs on Radio
Housing #2 EXCEPT tabs "B". The mounting tabs can be identified by the stamped letter on the back of each tab.
Mount Bracket #2 to the bottom of the
Housing with (2) #8 x ¾" Phillips Screws supplied. Skip to the Installation
Instructions for ALL VEHICLES on Page
#21.
7
1
FORD F-Series Pickup / Bronco 1992-96
2
1
FORD Windstar 1995-98
2
Disconnect the negative battery terminal to prevent an accidental short circuit. Using
Metra's 86-5618, pull the factory head unit from the dash and disconnect the wiring.
Cut and remove the shaft supports from the
Faceplate. Skip to step #3c in the
Installation Instructions for ALL VEHICLES on Page #22.
Disconnect the negative battery terminal to prevent an accidental short circuit. Using
Metra's 86-5618, pull the factory head unit from the dash and disconnect the wiring.
Cut and remove the shaft supports from the
Faceplate. Skip to step #3c in the
Installation Instructions for ALL VEHICLES on Page #22.
1
FORD Festiva 1988-93
2
1
JEEP Cherokee 1984-95 / Commanche 1986-92
Wagoneer 1984-96
2
"E"
"C"
8
Disconnect the negative battery terminal to prevent an accidental short circuit. Remove
(4) Phillips screws from the bottom of the dash trim bezel. Remove the bezel.
Remove (2) screws securing the factory head unit and disconnect the wiring.
Cut and remove all mounting tabs on Radio
Housing #1 EXCEPT tabs "C". The mounting tabs can be identified by the stamped letter on the back of each tab. Skip
to the Installation Instructions for ALL
VEHICLES on Page #21.
Disconnect the negative battery terminal to prevent an accidental short circuit. Unsnap the steering column trim panel and remove.
Remove (4) screws from the dash trim bezel and remove the bezel. Remove (2) screws securing the factory head unit and disconnect the wiring.
Cut and remove all mounting tabs on Radio
Housing #2 EXCEPT tabs "E". The mounting tabs can be identified by the stamped letter on the back of each tab. Skip
to the Installation Instructions for ALL
VEHICLES on Page #21.
13
1
FORD Thunderbird / MERCURY Cougar 1989-97
2 1
FORD Mustang 1994-00
2
Disconnect the negative battery terminal to prevent an accidental short circuit. Using
Metra's 86-5618, pull the factory head unti from the dash and disconnect the wiring.
Cut and remove the shaft supports from the
Faceplate. Skip to step #3c in the
Installation Instructions for ALL VEHICLES on Page #22.
Disconnect the negative battery terminal to prevent an accidental short circuit. Using
Metra's 86-5618, pull the factory head unit from the dash and disconnect the wiring.
Cut and remove the shaft supports from the
Faceplate. Skip to step #3c in the
Installation Instructions for ALL VEHICLES on Page #22.
1
FORD Thunderbird / MERCURY Cougar 1985-88
2
"D"
1
FORD Probe 1993-97
2
"F"
12
Disconnect the negative battery terminal to prevent an accidental short circuit. Remove
(2) screws from the top of the dash trim bezel. Open the ashtray and remove (2) screws from the ashtray cavity. Remove (4) screws securing the factory head unit and disconnect the wiring.
Cut and remove all mounting tabs on Radio
Housing #2 EXCEPT tabs "D" and "F".
The mounting tabs can be identified by the stamped letter on the back of each tab.
Locate Spacer Set #1. (The Spacers must be placed behind the mounting tabs during installation in step #5). Skip to the
Installation Instructions for ALL VEHICLES on Page #21.
Disconnect the negative battery terminal to prevent an accidental short circuit. Remove
(2) screws from the base of the dash trim bezel. Unclip and remove the bezel. Using
Metra's 86-5618, pull the factory head unit from the dash and disconnect the wiring.
Cut and remove the shaft supports from the
Faceplate. Skip to step #3c in the
Installation Instructions for ALL VEHICLES on Page #22.
9
1
FORD Taurus / MERCURY Sable 1990-95
2 1
FORD Tempo / MERCURY Topaz 1989-94
2
Disconnect the negative battery terminal to prevent an accidental short circuit. Using
Metra's 86-5618, pull the factory head unit from the dash and disconnect the wiring.
Cut and remove the shaft supports from the
Faceplate. Skip to step #3c in the
Installation Instructions for ALL VEHICLES on Page #22.
Disconnect the negative battery terminal to prevent an accidental short circuit. Using
Metra's 86-5618, pull the factory head unit from the dash and disconnect the wiring.
Cut and remove the shaft supports from the
Faceplate. Skip to step #3c in the
Installation Instructions for ALL VEHICLES on Page #22.
1
FORD Taurus / MERCURY Sable 1986-89
2
"A"
1
FORD Tempo / MERCURY Topaz 1985-88
2
"A"
10
"G"
Disconnect the negative battery terminal to prevent an accidental short circuit. Remove
(1) 7mm hex-head screw from the bottom of the radio trim bezel. Gently unclip the bezel and disconnect the antenna switch power lead. Remove (4) screws securing the factory head unit and disconnect the wiring.
Cut and remove all mounting tabs on Radio
Housing #2 EXCEPT tabs "A" and "G".
The mounting tabs can be identified by the stamped letter on the back of each tab. Skip
to the Installation Instructions for ALL
VEHICLES on Page #21.
"A"
Disconnect the negative battery terminal to prevent an accidental short circuit. Remove the ashtray by disengaging the release tab at the rear of the ashtray bracket. Remove
(2) screws from the lower edge of the dash trim bezel. Unclip the top edge of the bezel and remove. Remove (4) screws securing the factory head unit and disconnect the wiring.
Cut and remove all mounting tabs on Radio
Housing #1 EXCEPT tabs "A". The mounting tabs can be identified by the stamped letter on the back of each tab. Skip
to the Installation Instructions for ALL
VEHICLES on Page #21.
11
advertisement
Related manuals
advertisement