Mitsubishi Electric MSZ-HJ35VA-E1 Service manual

Revision A:
• MUZ-HJ50VA-
E1
has been added.
Please void OBH648.
SPLIT-TYPE AIR CONDITIONERS
OUTDOOR UNIT
SERVICE MANUAL
HFC
utilized
No. OBH648
REVISED EDITION-A
R410A
Models
MUZ-HJ25VA
MUZ-HJ35VA
MUZ-HJ50VA
-
E1
-
E1
-
E1
Indoor unit service manual
MSZ-HJ•VA Series (OBH647)
MUZ-HJ25VA
MUZ-HJ35VA
CONTENTS
1. TECHNICAL CHANGES ··································· 3
2. PART NAMES AND FUNCTIONS ····················· 3
3. SPECIFICATION ················································ 4
4. NOISE CRITERIA CURVES ······························ 7
5. OUTLINES AND DIMENSIONS ························ 8
6. WIRING DIAGRAM············································ 9
7. REFRIGERANT SYSTEM DIAGRAM ··············11
8. PERFORMANCE CURVES ····························· 13
9. ACTUATOR CONTROL ··································· 24
10. SERVICE FUNCTIONS···································· 25
11. TROUBLESHOOTING ····································· 25
12. DISASSEMBLY INSTRUCTIONS ···················· 42
PARTS CATALOG (OBB648)
NOTE:
RoHS compliant products have <G> mark on the spec name plate.
Use the specified refrigerant only
Never use any refrigerant other than that specified.
Doing so may cause a burst, an explosion, or fire when the unit is being used, serviced, or disposed of.
Correct refrigerant is specified in the manuals and on the spec labels provided with our products.
We will not be held responsible for mechanical failure, system malfunction, unit breakdown or accidents caused by
failure to follow the instructions.
<Preparation before the repair service>
Prepare the proper tools.
Prepare the proper protectors.
Provide adequate ventilation.
After stopping the operation of the air conditioner, turn off the power-supply breaker and remove the power plug.
Discharge the capacitor before the work involving the electric parts.
<Precautions during the repair service>
Do not perform the work involving the electric parts with wet hands.
Do not pour water into the electric parts.
Do not touch the refrigerant.
Do not touch the hot or cold areas in the refrigeration cycle.
When the repair or the inspection of the circuit needs to be done without turning off the power, exercise great caution not to
touch the live parts.
Revision A:
• MUZ-HJ50VA-
E1
has been added.
OBH648A
2
1
TECHNICAL CHANGES
MUZ-HJ25VA - E1
MUZ-HJ35VA - E1
MUZ-HJ50VA - E1
1. New model
2
PART NAMES AND FUNCTIONS
MUZ-HJ25VA MUZ-HJ35VA
Air inlet
(Back and side)
Piping
Drain hose
Air outlet
Drain outlet
MUZ-HJ50VA
Air inlet
(Back and side)
Piping
Drain hose
Air outlet
Drain outlet
ACCESSORIES
Drain socket
OBH648A
1
3
3
SPECIFICATION
Outdoor model
MUZ-HJ25VA
Power supply
Capacity
Rated frequency (Min.-Max.)
Cooling
Heating
Electrical data
Breaker Capacity
kW
A
Power input 1 (Total)
Running current 1
(Total)
Power factor 1 (Total)
Cooling
Heating
Cooling
Heating
Cooling
Heating
Starting current 1 (Total)
Coefficient of performance
(COP) 1 (Total)
W
A
%
A
Cooling
Heating
Model
Output
W
Cooling
Current 1
A
Heating
Refrigeration oil (Model)
L
Model
Fan motor
Current 1
A
Dimensions W × H × D
mm
Weight
kg
Dehumidification
Cooling
L/h
Air flow 1
m3/h
Cooling
Sound level 1
dB(A)
Heating
Fan speed
rpm
Fan speed regulator
Refrigerant filling capacity (R410A)
kg
Special remarks
Compressor
NOTE: Test conditions are based on ISO 5151.
Cooling: Indoor
Dry-bulb temperature 27°C
Outdoor Dry-bulb temperature 35°C
Heating: Indoor
Dry-bulb temperature 20°C
Outdoor Dry-bulb temperature 7°C
Refrigerant piping length (one way): 5 m
1 Measured under rated operating frequency.
OBH648A
MUZ-HJ35VA
Single phase, 230 V, 50 Hz
2.5 (1.3 - 3.0)
3.15 (1.4 - 3.5)
3.15 (0.9 - 3.5)
3.6 (1.1 - 4.1)
10
730
1,040
870
995
3.7
4.9
4.2
4.8
85
92
90
90
4.2
4.9
3.42
3.03
3.62
3.62
KNB065FUJHC
KNB073FUVHC
500
550
3.3
4.4
3.8
4.4
0.32 (NEO22)
RA6V21-BD
0.23
699 × 538 × 249
24
25
0.4
0.6
1,890
1,890
50
50
50
50
840
840
1
1
0.70
0.72
Wet-bulb temperature
19°C
Wet-bulb temperature
6°C
4
Outdoor model
MUZ-HJ50VA
Power supply
Single phase, 230 V, 50 Hz
5.0 (1.3 - 5.0)
5.4 (1.4 - 6.5)
12
2,050
1,480
9.0
6.6
99
97
9.0
2.44
3.65
SNB130FGBHT
900
8.5
5.9
0.45 (NEO22)
RC0J50-FA
0.27
0.34
800 × 550 × 285
36
2.2
1,872
1,872
1,086
2,088
1,776
1,386
50
51
810
810
490
900
770
610
3
1.15
Capacity
Rated frequency (Min.-Max.)
Cooling
Heating
Electrical data
Breaker Capacity
kW
A
Power input 1 (Total)
Running current 1
(Total)
Power factor 1 (Total)
Cooling
Heating
Cooling
Heating
Cooling
Heating
Starting current 1 (Total)
Coefficient of performance
(COP) 1 (Total)
W
A
%
A
Cooling
Heating
Model
Output
W
Cooling
Current 1
A
Heating
Refrigeration oil (Model)
L
Model
Fan motor
Cooling
Current 1
A
Heating
Dimensions W × H × D
mm
Weight
kg
Dehumidification
Cooling
L/h
High
Med.
Cooling
Low
Air flow 1
m3/h
High
Heating
Med.
Low
Cooling
Sound level 1
dB(A)
Heating
High
Cooling
Med.
Low
Fan speed
rpm
High
Heating
Med.
Low
Fan speed regulator
Refrigerant filling capacity (R410A)
kg
Special remarks
Compressor
NOTE: Test conditions are based on ISO 5151.
Cooling: Indoor
Dry-bulb temperature 27°C
Outdoor Dry-bulb temperature 35°C
Heating: Indoor
Dry-bulb temperature 20°C
Outdoor Dry-bulb temperature 7°C
Refrigerant piping length (one way): 5 m
1 Measured under rated operating frequency.
OBH648A
Wet-bulb temperature
19°C
Wet-bulb temperature
6°C
5
Specifications and rated conditions of main electric parts
Item
Smoothing capacitor
Diode module
Fuse
Power module
Expansion valve coil
Reactor
Switching power transistor
Circuit protection
Terminal block
Relay
R.V. coil
Model
MUZ-HJ25VA
(C61)
(DB61)
(DB65)
(F701, F801)
(IC700)
(LEV)
(L61)
(IC821)
(PTC64)
(TB)
(X61)
(X63)
(X64)
(21S4)
MUZ-HJ35VA
800 μF 420 V
15 A 600 V
10 A 600 V
T3.15AL250V
8 A 600 V
10 A 600 V
12 VDC
18 mH
30 A 600 V
33 Ω
3P
3 A 250 V
3 A 250 V
20 A 250 V
220 - 240 VAC
Specifications and rated conditions of main electric parts
Item
Smoothing capacitor
Diode module
Fuse
Power module
Expansion valve coil
Reactor
Circuit protection
Terminal block
Relay
R.V. coil
OBH648A
Model
MUZ-HJ50VA
(C61, C62, C63)
(DB61)
(F61)
(F701, F801, F901)
(IC700)
(IC820)
(IC932)
(LEV)
(L61)
(PTC64)
(PTC65)
(TB)
(X63)
(X64)
(21S4)
600 μF/ 620 μF 420 V
15 A 600 V
T20AL250V
T3.15AL250V
15 A 600 V
20A 600V
8A600V
12 VDC
23 mH
33 Ω
33 Ω
5P
3 A 250 V
20 A 250 V
220 - 240 VAC
6
4
NOISE CRITERIA CURVES
MUZ-HJ35VA
MUZ-HJ25VA
FUNCTION
SPL(dB(A))
LINE
50
HEATING
LINE
90
OCTAVE BAND SOUND PRESSURE LEVEL, dB re 0.0002 MICRO BAR
OCTAVE BAND SOUND PRESSURE LEVEL, dB re 0.0002 MICRO BAR
50
50
HEATING
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
NC-20
NC-10
63
125
250
500
1000
2000
4000
8000
BAND CENTER FREQUENCIES, Hz
FUNCTION
SPL(dB(A))
COOLING
50
HEATING
51
80
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
NC-20
NC-10
10
63
125
250
LINE
OUTDOOR UNIT
1m
MICROPHONE
80
70
NC-70
60
NC-60
50
NC-50
40
NC-40
30
NC-30
20
NC-20
NC-10
125
250
500
1000
2000
4000
8000
BAND CENTER FREQUENCIES, Hz
OBH648A
1000
2000
4000
8000
Test conditions
Cooling : Dry-bulb temperature 35°C
Heating : Dry-bulb temperature 7°C Wet-bulb temperature
90
63
500
BAND CENTER FREQUENCIES, Hz
MUZ-HJ50VA
OCTAVE BAND SOUND PRESSURE LEVEL, dB re 0.0002 MICRO BAR
50
COOLING
80
10
SPL(dB(A))
COOLING
90
10
FUNCTION
7
6°C
5
OUTLINES AND DIMENSIONS
Unit : mm
MUZ-HJ25VA MUZ-HJ35VA
REQUIRED SPACE
Air in
100 mm or more
100 mm or more
100
mm
Air out
or m
ore
19.6
Air in
285
Bolt pitch for
installation
294~267
41.5
Drain hole ø33
2 - 10.3 X 19.3 Oval hole
349.5
249
17.9
200 mm or more
350
m
mo
rm
ore
157.7
102.7
13.5
°
40
43°
270.3
538
Liquid refrigerant pipe joint
Refrigerant pipe (flared) ø6.35
Gas refrigerant pipe joint
Refrigerant pipe (flared) ø9.52
259
121.4
121
500
55.7
699
MUZ-HJ50VA
REQUIRED SPACE
400
Drain hole ø42
100 mm or more
Bolt pitch for
installation
304~325
44
285
100 mm or more
Air in
100
mm
or m
ore
40
2 - 10 X 21 Oval hole
17.5
350
Air out
22.3
mm
or m
ore
200 mm or more
Service panel
23
35°
69
302.5
170.5
Service port
500 Bolt pitch for installation
800
OBH648A
Gas refrigerant pipe joint
Refrigerant pipe (flared) ø9.52
99.5
10
164.5
280
150
8
43°
Liquid refrigerant pipe joint
Refrigerant pipe (flared) ø6.35
Handle
550
344.5
Air in
6
WIRING DIAGRAM
MUZ-HJ25VA
MUZ-HJ35VA
OBH648A
9
MUZ-HJ50VA
OBH648A
10
7
REFRIGERANT SYSTEM DIAGRAM
Unit : mm
MUZ-HJ25VA MUZ-HJ35VA
Refrigerant pipe ø9.52
(with heat insulator)
4-way valve
Muffler
(HJ35 only)
Stop valve
(with service port)
Discharge
temperature
thermistor
RT62
Flared connection
Outdoor
heat
exchanger
Muffler
Compressor
Defrost
thermistor
RT61
Flared connection
Refrigerant pipe ø6.35
(with heat insulator)
Strainer
#100
Capillary tube
ø3.0 × ø1.4 × 260
LEV
R.V. coil
heating OFF
cooling ON
Stop valve
(with strainer)
Refrigerant flow in cooling
Refrigerant flow in heating
MUZ-HJ50VA
4-way valve
Refrigerant pipe ø12.7
(with heat insulator)
Muffler
Stop valve
(with service port)
Discharge
temperature
thermistor
RT62
Flared connection
Outdoor
heat
exchanger
Muffler
Compressor
Defrost
thermistor
RT61
Flared connection
Refrigerant pipe ø6.35
(with heat insulator)
Strainer
#100
Capillary tube
ø4.0 × ø2.4 × 240
LEV
R.V. coil
heating ON
cooling OFF
Stop valve
(with strainer)
Refrigerant flow in cooling
Refrigerant flow in heating
OBH648A
11
MAX. REFRIGERANT PIPING LENGTH and MAX. HEIGHT DIFFERENCE
Refrigerant piping: m
MUZ-HJ25VA
MUZ-HJ35VA
Max. Length
A
Max. Height difference
B
20
12
Piping size O.D: mm
Gas
Liquid
9.52
6.35
12.7
MUZ-HJ50VA
Indoor
unit
Max. Height
difference
B
Max. Length
A
Outdoor unit
ADDITIONAL REFRIGERANT CHARGE (R410A : g)
Model
MUZ-HJ25VA
MUZ-HJ35VA
MUZ-HJ50VA
Outdoor unit
precharged
700
720
1,150
5m
6m
7m
0
0
0
Refrigerant piping length (one way)
8m
9 m 10 m 11 m 12 m 13 m 14 m 15 m 20 m
20
40
60
80
100
120
140
160
260
Calculation: X g = 20 g/m (Refrigerant piping length (m) - 7)
NOTE : Refrigerant piping exceeding 7 m requires additional refrigerant charge according to the calculation.
OBH648A
12
8
PERFORMANCE CURVES
MUZ-HJ25VA MUZ-HJ35VA MUZ-HJ50VA
The standard specifications apply only to the operation of the air conditioner under normal conditions. Since operating conditions vary according to the areas where these units are installed, the following information has been provided to clarify the
operating characteristics of the air conditioner under the conditions indicated by the performance curve.
(1) GUARANTEED VOLTAGE
198 ~ 264 V, 50 Hz
(2) AIR FLOW
Air flow should be set at MAX.
(3) MAIN READINGS
(1) Indoor intake air wet-bulb temperature :
°C WB
(2) Indoor outlet air wet-bulb temperature :
°C WB
Cooling
(3) Outdoor intake air dry-bulb temperature :
°C DB
(4) Total input:
W
(5) Indoor intake air dry-bulb temperature :
°C DB
(6) Outdoor intake air wet-bulb temperature :
°C WB
Heating
(7) Total input :
W
Indoor air wet and dry bulb temperature difference on the left side of the following chart shows the difference between the
indoor intake air wet and dry bulb temperature and the indoor outlet air wet and dry bulb temperature for your reference at
service.
}
}
How to measure the indoor air wet and dry bulb temperature difference
1. Attach at least 2 sets of wet and dry bulb thermometers to the indoor air intake as shown in the figure, and at least 2 sets
of wet and dry bulb thermometers to the indoor air outlet. The thermometers must be attached to the position where air
speed is high.
2. Attach at least 2 sets of wet and dry bulb thermometers to the outdoor air intake.
Cover the thermometers to prevent direct rays of the sun.
3. Check that the air filter is cleaned.
4. Open windows and doors of room.
5. Press the EMERGENCY OPERATION switch once (twice) to start the EMERGENCY COOL (HEAT) MODE.
6. When system stabilizes after more than 15 minutes, measure temperature and take an average temperature.
7. 10 minutes later, measure temperature again and check that the temperature does not change.
INDOOR UNIT
OUTDOOR UNIT
Wet and dry bulb
thermometers
FRONT VIEW
OBH648A
Wet and dry bulb
thermometers
BACK VIEW
13
7.2
8.0
11.4
6.7
7.4
10.5
6.1
6.8
9.6
5.6
6.2
8.7
5.1
5.6
7.9
4.6
5.1
7.1
4.1
4.5
6.3
Cooling capacity (at Rated frequency)
1.5
Capacity correction factor
Indoor air Wet-bulb temperature
difference (°C)
8-1. CAPACITY AND INPUT CURVES
1.4
1.3
26
1.2
Indo
or in
1.1
1.0
8.7
5.6
7.9
4.6
5.1
7.1
4.1
4.5
6.3
3.6
4.0
5.5
MUZ-HJ35VA
22.9
24.7
19.0
21.1
22.8
17.4
19.3
20.9
15.8
17.6
19.0
14.3
15.8
17.1
15.2
12.3
13.3
9.5
10.5
11.4
MUZ-HJ50VA
14.1
11.1
MUZ-HJ35VA
12.7
MUZ-HJ25VA
Indoor air Wet-bulb temperature
difference (°C)
20.6
Input correction factor
6.2
5.1
MUZ-HJ50VA
5.6
OBH648A
mpe
ratu
re (°
0.9
20
22
20
18
4546
C)
25
30
35
Outdoor intake air Dry-bulb temperature (°C)
MUZ-HJ50VA
MUZ-HJ35VA
MUZ-HJ25VA
9.6
MUZ-HJ25VA
Indoor air Wet-bulb temperature
difference (°C)
6.8
24
air W
et-bu
lb te
18
6.1
take
40
Total input (Cooling :at Rated frequency)
1.3
1.2
22
20
18
24
26
1.1
1.0
0.9
0.8
k
r inta
Indoo
18 20
25
)
re (°C
peratu
lb tem
et-bu
e air W
30
35
40
45 46
Outdoor intake air Dry-bulb temperature (°C)
Heating capacity (at Rated frequency)
ure
rat
lb
bu
ir
ea
tak
in
or
yDr
e
mp
Total input (Heating at Rated frequency)
C)
(°
te
ake
int
oor
Ind
u
ry-b
air D
ture
pera
m
lb te
(°C)
o
Ind
Outdoor intake air Wet-bulb temperature (°C)
Outdoor intake air Wet-bulb temperature (°C)
NOTE: The above broken lines are for the heating operation without any frost and
defrost operation.
14
8-2. CAPACITY AND INPUT CORRECTION BY OPERATIONAL FREQUENCY OF COMPRESSOR
MUZ-HJ25VA
1.5
Input correction factors
Capacity correction factors
Correction of Cooling total input
1.0
1.0
0.5
0.5
0
50
100
150 (Hz)
0
50
100
150 (Hz)
Correction of Heating total input
1.5
Correction of Heating capacity
Input correction factors
1.5
1.5
Capacity correction factors
Correction of Cooling capacity
1.0
0.5
0
50
100
150 (Hz)
The operational frequency of compressor The operational frequency of compressor The operational frequency of compressor
1.0
0.5
0
50
100
150(Hz)
The operational frequency of compressor
MUZ-HJ35VA
1.5
1.0
1.0
0.5
0.5
0
50
100
150 (Hz)
0
50
100
150 (Hz)
Correction of Heating total input
1.5
Correction of Heating capacity
Input correction factors
Correction of Cooling total input
Input correction factors
Capacity correction factors
1.5
Capacity correction factors
Correction of Cooling capacity
1.5
1.0
0.5
0
50
100
150 (Hz)
The operational frequency of compressor The operational frequency of compressor The operational frequency of compressor
1.0
0.5
0
50
100
150(Hz)
The operational frequency of compressor
MUZ-HJ50VA
1.0
1.5
1.0
0.5
0
Correction of Cooling total input
0.5
50
100
150 (Hz)
0
50
100
150 (Hz)
Correction of Heating total input
1.5
Correction of Heating capacity
Input correction factors
1.5
Input correction factors
Capacity correction factors
1.5
Capacity correction factors
Correction of Cooling capacity
1.0
0.5
0
50
100
150 (Hz)
The operational frequency of compressor The operational frequency of compressor The operational frequency of compressor
8-3. HOW TO OPERATE FIXED-FREQUENCY OPERATION
1.0
0.5
0
50
100
150(Hz)
The operational frequency of compressor
<Test run operation>
1. Press EMERGENCY OPERATION switch to start COOL or HEAT mode (COOL: Press once, HEAT: Press twice).
2. Test run operation starts and continues to operate for 30 minutes.
3. Compressor operates at rated frequency in COOL mode or 58 Hz in HEAT mode.
4. Indoor fan operates at High speed.
5. After 30 minutes, test run operation finishes and EMERGENCY OPERATION starts (operation frequency of compressor varies).
6. To cancel test run operation (EMERGENCY OPERATION), press EMERGENCY OPERATION switch or any button on
remote controller.
OBH648A
15
8-4. OUTDOOR LOW PRESSURE AND OUTDOOR UNIT CURRENT
COOL operation
Dry-bulb temperature (°C)
20
25
30
Both indoor and outdoor unit are under the same temperature/humidity condition.
Operation: TEST RUN OPERATION (Refer to 8-3.)
Relative humidity (%)
50
60
70
Outdoor low pressure
MUZ-HJ25VA
(kgf/cm2 [Gauge])(MPa [Gauge])
9 0.9
MUZ-HJ35VA
(kgf/cm2 [Gauge])(MPa [Gauge])
8 0.8
MUZ-HJ50VA
(kgf/cm2 [Gauge])(MPa [Gauge])
7 0.7
8
0.8
7
0.7
6
0.6
7
0.7
6
0.6
5
0.5
6
0.6
5
0.5
4
0.4
5
0.5
4
0.4
3
0.3
4
0.4
15 18 20
25
30 32 35 (°C)
(%)
50
60
70
Ambient temperature(°C)
Ambient humidity(%)
3
0.3
15
2
0.2
15
25
30 32 35 (°C)
18 20
(%)
50
60
70
Ambient temperature(°C)
Ambient humidity(%)
25
30 32 35 (°C)
18 20
(%)
50
60
70
Ambient temperature(°C)
Ambient humidity(%)
NOTE : The unit of pressure has been changed to MPa on the international system of units (SI unit system).
The conversion factor is: 1 (MPa [Gauge]) = 10.2 (kgf/cm2[Gauge])
Outdoor unit current
MUZ-HJ25VA
MUZ-HJ35VA
3
10
Outdoor current (A)
4
2
15
MUZ-HJ50VA
6
Outdoor current (A)
Outdoor current (A)
5
5
4
3
15
1820
25
30 32 35(°C)
(%)
50
60
70
Ambient temperature (°C)
Ambient humidity(%)
9
8
7
6
5
15
1820
25
30 32 35(°C)
50
60
70
(%)
Ambient temperature (°C)
Ambient humidity(%)
1820
25
30 32 35(°C)
50
60
70
(%)
Ambient temperature (°C)
Ambient humidity(%)
HEAT operation
Condition:
Dry bulb temperature (°C)
Wet bulb temperature (°C)
Indoor
20.0
14.5
2
1
Outdoor
7
15
6
12
20.0
14.5
Operation: Test run operation (refer to 8-3.)
Outdoor unit current
MUZ-HJ25VA
2.0
15
20
25
5
10
Ambient temperature (°C)
OBH648A
6
Outdoor current (A)
Outdoor current (A)
Outdoor current (A)
3.0
2.5
1.5
0
MUZ-HJ50VA
MUZ-HJ35VA
3.0
2.5
2.0
1.5
0
15
20
25
5
10
Ambient temperature (°C)
16
5
4
3
0
5
10
15
20
Ambient temperature (°C)
25
PERFORMANCE DATA COOL operation at Rated frequency
MUZ-HJ25VA
CAPACITY: 2.5 kW
INDOOR INDOOR
DB (°C) WB (°C)
21
21
22
22
22
23
23
23
24
24
24
24
25
25
25
25
26
26
26
26
26
27
27
27
27
27
28
28
28
28
28
29
29
29
29
29
30
30
30
30
30
31
31
31
31
31
32
32
32
32
32
NOTE
18
20
18
20
22
18
20
22
18
20
22
24
18
20
22
24
18
20
22
24
26
18
20
22
24
26
18
20
22
24
26
18
20
22
24
26
18
20
22
24
26
18
20
22
24
26
18
20
22
24
26
SHF: 0.89
Q
INPUT: 730 W
21
SHC SHF INPUT
Q
OUTDOOR DB (°C)
25
27
SHC SHF INPUT
Q
SHC SHF INPUT
Q
30
SHC SHF INPUT
2.94
2.09
0.71
584
2.81
2.00
0.71
613
2.70
1.92
0.71
642
2.60
1.85
0.71
672
3.06
1.81
0.59
613
2.94
1.73
0.59
650
2.85
1.68
0.59
664
2.75
1.62
0.59
694
2.94
2.20
0.75
584
2.81
2.11
0.75
613
2.70
2.03
0.75
642
2.60
1.95
0.75
672
3.06
1.93
0.63
613
2.94
1.85
0.63
650
2.85
1.80
0.63
664
2.75
1.73
0.63
694
3.19
1.63
0.51
635
3.08
1.57
0.51
675
3.00
1.53
0.51
694
2.88
1.47
0.51
723
2.94
2.32
0.79
584
2.81
2.22
0.79
613
2.70
2.13
0.79
642
2.60
2.05
0.79
672
3.06
2.05
0.67
613
2.94
1.97
0.67
650
2.85
1.91
0.67
664
2.75
1.84
0.67
694
3.19
1.75
0.55
635
3.08
1.69
0.55
675
3.00
1.65
0.55
694
2.88
1.58
0.55
723
2.94
2.44
0.83
584
2.81
2.33
0.83
613
2.70
2.24
0.83
642
2.60
2.16
0.83
672
3.06
2.17
0.71
613
2.94
2.09
0.71
650
2.85
2.02
0.71
664
2.75
1.95
0.71
694
3.19
1.88
0.59
635
3.08
1.81
0.59
675
3.00
1.77
0.59
694
2.88
1.70
0.59
723
3.35
1.57
0.47
664
3.23
1.52
0.47
701
3.15
1.48
0.47
723
3.05
1.43
0.47
759
2.94
2.56
0.87
584
2.81
2.45
0.87
613
2.70
2.35
0.87
642
2.60
2.26
0.87
672
3.06
2.30
0.75
613
2.94
2.20
0.75
650
2.85
2.14
0.75
664
2.75
2.06
0.75
694
3.19
2.01
0.63
635
3.08
1.94
0.63
675
3.00
1.89
0.63
694
2.88
1.81
0.63
723
3.35
1.71
0.51
664
3.23
1.64
0.51
701
3.15
1.61
0.51
723
3.05
1.56
0.51
759
2.94
2.67
0.91
584
2.81
2.56
0.91
613
2.70
2.46
0.91
642
2.60
2.37
0.91
672
3.06
2.42
0.79
613
2.94
2.32
0.79
650
2.85
2.25
0.79
664
2.75
2.17
0.79
694
3.19
2.14
0.67
635
3.08
2.06
0.67
675
3.00
2.01
0.67
694
2.88
1.93
0.67
723
3.35
1.84
0.55
664
3.23
1.77
0.55
701
3.15
1.73
0.55
723
3.05
1.68
0.55
759
3.45
1.48
0.43
701
3.35
1.44
0.43
737
3.30
1.42
0.43
759
3.20
1.38
0.43
781
2.94
2.79
0.95
584
2.81
2.67
0.95
613
2.70
2.57
0.95
642
2.60
2.47
0.95
672
3.06
2.54
0.83
613
2.94
2.44
0.83
650
2.85
2.37
0.83
664
2.75
2.28
0.83
694
3.19
2.26
0.71
635
3.08
2.18
0.71
675
3.00
2.13
0.71
694
2.88
2.04
0.71
723
3.35
1.98
0.59
664
3.23
1.90
0.59
701
3.15
1.86
0.59
723
3.05
1.80
0.59
759
3.45
1.62
0.47
701
3.35
1.57
0.47
737
3.30
1.55
0.47
759
3.20
1.50
0.47
781
2.94
2.91
0.99
584
2.81
2.78
0.99
613
2.70
2.67
0.99
642
2.60
2.57
0.99
672
3.06
2.66
0.87
613
2.94
2.56
0.87
650
2.85
2.48
0.87
664
2.75
2.39
0.87
694
3.19
2.39
0.75
635
3.08
2.31
0.75
675
3.00
2.25
0.75
694
2.88
2.16
0.75
723
3.35
2.11
0.63
664
3.23
2.03
0.63
701
3.15
1.98
0.63
723
3.05
1.92
0.63
759
3.45
1.76
0.51
701
3.35
1.71
0.51
737
3.30
1.68
0.51
759
3.20
1.63
0.51
781
2.94
2.94
1.00
584
2.81
2.81
1.00
613
2.70
2.70
1.00
642
2.60
2.60
1.00
672
3.06
2.79
0.91
613
2.94
2.67
0.91
650
2.85
2.59
0.91
664
2.75
2.50
0.91
694
3.19
2.52
0.79
635
3.08
2.43
0.79
675
3.00
2.37
0.79
694
2.88
2.27
0.79
723
3.35
2.24
0.67
664
3.23
2.16
0.67
701
3.15
2.11
0.67
723
3.05
2.04
0.67
759
3.45
1.90
0.55
701
3.35
1.84
0.55
737
3.30
1.82
0.55
759
3.20
1.76
0.55
781
2.94
2.94
1.00
584
2.81
2.81
1.00
613
2.70
2.70
1.00
642
2.60
2.60
1.00
672
3.06
2.91
0.95
613
2.94
2.79
0.95
650
2.85
2.71
0.95
664
2.75
2.61
0.95
694
3.19
2.65
0.83
635
3.08
2.55
0.83
675
3.00
2.49
0.83
694
2.88
2.39
0.83
723
3.35
2.38
0.71
664
3.23
2.29
0.71
701
3.15
2.24
0.71
723
3.05
2.17
0.71
759
3.45
2.04
0.59
701
3.35
1.98
0.59
737
3.30
1.95
0.59
759
3.20
1.89
0.59
781
2.94
2.94
1.00
584
2.81
2.81
1.00
613
2.70
2.70
1.00
642
2.60
2.60
1.00
672
3.06
3.03
0.99
613
2.94
2.91
0.99
650
2.85
2.82
0.99
664
2.75
2.72
0.99
694
3.19
2.77
0.87
635
3.08
2.68
0.87
675
3.00
2.61
0.87
694
2.88
2.50
0.87
723
3.35
2.51
0.75
664
3.23
2.42
0.75
701
3.15
2.36
0.75
723
3.05
2.29
0.75
759
3.45
2.17
0.63
701
3.35
2.11
0.63
737
3.30
2.08
0.63
759
3.20
2.02
0.63
781
2.94
2.94
1.00
584
2.81
2.81
1.00
613
2.70
2.70
1.00
642
2.60
2.60
1.00
672
3.06
3.06
1.00
613
2.94
2.94
1.00
650
2.85
2.85
1.00
664
2.75
2.75
1.00
694
3.19
2.90
0.91
635
3.08
2.80
0.91
675
3.00
2.73
0.91
694
2.88
2.62
0.91
723
3.35
2.65
0.79
664
3.23
2.55
0.79
701
3.15
2.49
0.79
723
3.05
2.41
0.79
759
3.45
2.31
0.67
701
3.35
2.24
0.67
737
3.30
2.21
0.67
759
3.20
2.14
0.67
781
Q : Total capacity (kW)
SHC : Sensible heat capacity (kW)
OBH648A
SHF : Sensible heat factor
INPUT : Total power input (W)
17
DB : Dry-bulb temperature
WB : Wet-bulb temperature
PERFORMANCE DATA COOL operation at Rated frequency
MUZ-HJ25VA
CAPACITY: 2.5 kW
INDOOR INDOOR
DB (°C) WB (°C)
21
21
22
22
22
23
23
23
24
24
24
24
25
25
25
25
26
26
26
26
26
27
27
27
27
27
28
28
28
28
28
29
29
29
29
29
30
30
30
30
30
31
31
31
31
31
32
32
32
32
32
NOTE
18
20
18
20
22
18
20
22
18
20
22
24
18
20
22
24
18
20
22
24
26
18
20
22
24
26
18
20
22
24
26
18
20
22
24
26
18
20
22
24
26
18
20
22
24
26
18
20
22
24
26
SHF: 0.89
Q
INPUT: 730 W
35
SHC SHF INPUT
OUTDOOR DB (°C)
40
Q
SHC SHF INPUT
Q
46
SHC SHF INPUT
2.45
1.74
0.71
715
2.25
1.60
0.71
759
2.08
1.47
0.71
788
2.58
1.52
0.59
745
2.40
1.42
0.59
781
2.23
1.31
0.59
825
2.45
1.84
0.75
715
2.25
1.69
0.75
759
2.08
1.56
0.75
788
2.58
1.62
0.63
745
2.40
1.51
0.63
781
2.23
1.40
0.63
825
2.73
1.39
0.51
774
2.55
1.30
0.51
818
2.38
1.21
0.51
847
2.45
1.94
0.79
715
2.25
1.78
0.79
759
2.08
1.64
0.79
788
2.58
1.73
0.67
745
2.40
1.61
0.67
781
2.23
1.49
0.67
825
2.73
1.50
0.55
774
2.55
1.40
0.55
818
2.38
1.31
0.55
847
2.45
2.03
0.83
715
2.25
1.87
0.83
759
2.08
1.72
0.83
788
2.58
1.83
0.71
745
2.40
1.70
0.71
781
2.23
1.58
0.71
825
2.73
1.61
0.59
774
2.55
1.50
0.59
818
2.38
1.40
0.59
847
2.88
1.35
0.47
803
2.70
1.27
0.47
839
2.55
1.20
0.47
876
2.45
2.13
0.87
715
2.25
1.96
0.87
759
2.08
1.81
0.87
788
2.58
1.93
0.75
745
2.40
1.80
0.75
781
2.23
1.67
0.75
825
2.73
1.72
0.63
774
2.55
1.61
0.63
818
2.38
1.50
0.63
847
2.88
1.47
0.51
803
2.70
1.38
0.51
839
2.55
1.30
0.51
876
2.45
2.23
0.91
715
2.25
2.05
0.91
759
2.08
1.89
0.91
788
2.58
2.03
0.79
745
2.40
1.90
0.79
781
2.23
1.76
0.79
825
2.73
1.83
0.67
774
2.55
1.71
0.67
818
2.38
1.59
0.67
847
2.88
1.58
0.55
803
2.70
1.49
0.55
839
2.55
1.40
0.55
876
3.03
1.30
0.43
832
2.85
1.23
0.43
869
2.68
1.15
0.43
905
2.45
2.33
0.95
715
2.25
2.14
0.95
759
2.08
1.97
0.95
788
2.58
2.14
0.83
745
2.40
1.99
0.83
781
2.23
1.85
0.83
825
2.73
1.93
0.71
774
2.55
1.81
0.71
818
2.38
1.69
0.71
847
2.88
1.70
0.59
803
2.70
1.59
0.59
839
2.55
1.50
0.59
876
3.03
1.42
0.47
832
2.85
1.34
0.47
869
2.68
1.26
0.47
905
2.45
2.43
0.99
715
2.25
2.23
0.99
759
2.08
2.05
0.99
788
2.58
2.24
0.87
745
2.40
2.09
0.87
781
2.23
1.94
0.87
825
2.73
2.04
0.75
774
2.55
1.91
0.75
818
2.38
1.78
0.75
847
2.88
1.81
0.63
803
2.70
1.70
0.63
839
2.55
1.61
0.63
876
3.03
1.54
0.51
832
2.85
1.45
0.51
869
2.68
1.36
0.51
905
2.45
2.45
1.00
715
2.25
2.25
1.00
759
2.08
2.08
1.00
788
2.58
2.34
0.91
745
2.40
2.18
0.91
781
2.23
2.02
0.91
825
2.73
2.15
0.79
774
2.55
2.01
0.79
818
2.38
1.88
0.79
847
2.88
1.93
0.67
803
2.70
1.81
0.67
839
2.55
1.71
0.67
876
3.03
1.66
0.55
832
2.85
1.57
0.55
869
2.68
1.47
0.55
905
2.45
2.45
1.00
715
2.25
2.25
1.00
759
2.08
2.08
1.00
788
2.58
2.45
0.95
745
2.40
2.28
0.95
781
2.23
2.11
0.95
825
2.73
2.26
0.83
774
2.55
2.12
0.83
818
2.38
1.97
0.83
847
2.88
2.04
0.71
803
2.70
1.92
0.71
839
2.55
1.81
0.71
876
3.03
1.78
0.59
832
2.85
1.68
0.59
869
2.68
1.58
0.59
905
2.45
2.45
1.00
715
2.25
2.25
1.00
759
2.08
2.08
1.00
788
2.58
2.55
0.99
745
2.40
2.38
0.99
781
2.23
2.20
0.99
825
2.73
2.37
0.87
774
2.55
2.22
0.87
818
2.38
2.07
0.87
847
2.88
2.16
0.75
803
2.70
2.03
0.75
839
2.55
1.91
0.75
876
3.03
1.91
0.63
832
2.85
1.80
0.63
869
2.68
1.69
0.63
905
2.45
2.45
1.00
715
2.25
2.25
1.00
759
2.08
2.08
1.00
788
2.58
2.58
1.00
745
2.40
2.40
1.00
781
2.23
2.23
1.00
825
2.73
2.48
0.91
774
2.55
2.32
0.91
818
2.38
2.16
0.91
847
2.88
2.27
0.79
803
2.70
2.13
0.79
839
2.55
2.01
0.79
876
3.03
2.03
0.67
832
2.85
1.91
0.67
869
2.68
1.79
0.67
905
Q : Total capacity (kW)
SHC : Sensible heat capacity (kW)
OBH648A
SHF : Sensible heat factor
INPUT : Total power input (W)
18
DB : Dry-bulb temperature
WB : Wet-bulb temperature
PERFORMANCE DATA COOL operation at Rated frequency
MUZ-HJ35VA
CAPACITY: 3.15 kW
INDOOR INDOOR
DB (°C) WB (°C)
21
21
22
22
22
23
23
23
24
24
24
24
25
25
25
25
26
26
26
26
26
27
27
27
27
27
28
28
28
28
28
29
29
29
29
29
30
30
30
30
30
31
31
31
31
31
32
32
32
32
32
NOTE
18
20
18
20
22
18
20
22
18
20
22
24
18
20
22
24
18
20
22
24
26
18
20
22
24
26
18
20
22
24
26
18
20
22
24
26
18
20
22
24
26
18
20
22
24
26
18
20
22
24
26
Q
SHF: 0.87
INPUT: 1040 W
21
SHC SHF INPUT
Q
OUTDOOR DB (°C)
25
27
SHC SHF INPUT
Q
SHC SHF INPUT
Q
30
SHC SHF INPUT
3.70
2.55
0.69
832
3.54
2.45
0.69
874
3.40
2.35
0.69
915
3.28
2.26
0.69
957
3.86
2.20
0.57
874
3.70
2.11
0.57
926
3.59
2.05
0.57
946
3.47
1.98
0.57
988
3.70
2.70
0.73
832
3.54
2.59
0.73
874
3.40
2.48
0.73
915
3.28
2.39
0.73
957
3.86
2.35
0.61
874
3.70
2.26
0.61
926
3.59
2.19
0.61
946
3.47
2.11
0.61
988
4.02
1.97
0.49
905
3.87
1.90
0.49
962
3.78
1.85
0.49
988
3.62
1.78
0.49
1030
3.70
2.85
0.77
832
3.54
2.73
0.77
874
3.40
2.62
0.77
915
3.28
2.52
0.77
957
3.86
2.51
0.65
874
3.70
2.41
0.65
926
3.59
2.33
0.65
946
3.47
2.25
0.65
988
4.02
2.13
0.53
905
3.87
2.05
0.53
962
3.78
2.00
0.53
988
3.62
1.92
0.53
1030
3.70
3.00
0.81
832
3.54
2.87
0.81
874
3.40
2.76
0.81
915
3.28
2.65
0.81
957
3.86
2.66
0.69
874
3.70
2.55
0.69
926
3.59
2.48
0.69
946
3.47
2.39
0.69
988
4.02
2.29
0.57
905
3.87
2.21
0.57
962
3.78
2.15
0.57
988
3.62
2.06
0.57
1030
4.22
1.90
0.45
946
4.06
1.83
0.45
998
3.97
1.79
0.45
1030
3.84
1.73
0.45
1082
3.70
3.15
0.85
832
3.54
3.01
0.85
874
3.40
2.89
0.85
915
3.28
2.78
0.85
957
3.86
2.82
0.73
874
3.70
2.70
0.73
926
3.59
2.62
0.73
946
3.47
2.53
0.73
988
4.02
2.45
0.61
905
3.87
2.36
0.61
962
3.78
2.31
0.61
988
3.62
2.21
0.61
1030
4.22
2.07
0.49
946
4.06
1.99
0.49
998
3.97
1.94
0.49
1030
3.84
1.88
0.49
1082
3.70
3.29
0.89
832
3.54
3.15
0.89
874
3.40
3.03
0.89
915
3.28
2.92
0.89
957
3.86
2.97
0.77
874
3.70
2.85
0.77
926
3.59
2.77
0.77
946
3.47
2.67
0.77
988
4.02
2.61
0.65
905
3.87
2.52
0.65
962
3.78
2.46
0.65
988
3.62
2.35
0.65
1030
4.22
2.24
0.53
946
4.06
2.15
0.53
998
3.97
2.10
0.53
1030
3.84
2.04
0.53
1082
4.35
1.78
0.41
998
4.22
1.73
0.41
1050
4.16
1.70
0.41
1082
4.03
1.65
0.41
1113
3.70
3.44
0.93
832
3.54
3.30
0.93
874
3.40
3.16
0.93
915
3.28
3.05
0.93
957
3.86
3.13
0.81
874
3.70
3.00
0.81
926
3.59
2.91
0.81
946
3.47
2.81
0.81
988
4.02
2.77
0.69
905
3.87
2.67
0.69
962
3.78
2.61
0.69
988
3.62
2.50
0.69
1030
4.22
2.41
0.57
946
4.06
2.32
0.57
998
3.97
2.26
0.57
1030
3.84
2.19
0.57
1082
4.35
1.96
0.45
998
4.22
1.90
0.45
1050
4.16
1.87
0.45
1082
4.03
1.81
0.45
1113
3.70
3.59
0.97
832
3.54
3.44
0.97
874
3.40
3.30
0.97
915
3.28
3.18
0.97
957
3.86
3.28
0.85
874
3.70
3.15
0.85
926
3.59
3.05
0.85
946
3.47
2.95
0.85
988
4.02
2.93
0.73
905
3.87
2.83
0.73
962
3.78
2.76
0.73
988
3.62
2.64
0.73
1030
4.22
2.57
0.61
946
4.06
2.48
0.61
998
3.97
2.42
0.61
1030
3.84
2.34
0.61
1082
4.35
2.13
0.49
998
4.22
2.07
0.49
1050
4.16
2.04
0.49
1082
4.03
1.98
0.49
1113
3.70
3.70
1.00
832
3.54
3.54
1.00
874
3.40
3.40
1.00
915
3.28
3.28
1.00
957
3.86
3.43
0.89
874
3.70
3.29
0.89
926
3.59
3.20
0.89
946
3.47
3.08
0.89
988
4.02
3.09
0.77
905
3.87
2.98
0.77
962
3.78
2.91
0.77
988
3.62
2.79
0.77
1030
4.22
2.74
0.65
946
4.06
2.64
0.65
998
3.97
2.58
0.65
1030
3.84
2.50
0.65
1082
4.35
2.30
0.53
998
4.22
2.24
0.53
1050
4.16
2.20
0.53
1082
4.03
2.14
0.53
1113
3.70
3.70
1.00
832
3.54
3.54
1.00
874
3.40
3.40
1.00
915
3.28
3.28
1.00
957
3.86
3.59
0.93
874
3.70
3.44
0.93
926
3.59
3.34
0.93
946
3.47
3.22
0.93
988
4.02
3.25
0.81
905
3.87
3.14
0.81
962
3.78
3.06
0.81
988
3.62
2.93
0.81
1030
4.22
2.91
0.69
946
4.06
2.80
0.69
998
3.97
2.74
0.69
1030
3.84
2.65
0.69
1082
4.35
2.48
0.57
998
4.22
2.41
0.57
1050
4.16
2.37
0.57
1082
4.03
2.30
0.57
1113
3.70
3.70
1.00
832
3.54
3.54
1.00
874
3.40
3.40
1.00
915
3.28
3.28
1.00
957
3.86
3.74
0.97
874
3.70
3.59
0.97
926
3.59
3.48
0.97
946
3.47
3.36
0.97
988
4.02
3.41
0.85
905
3.87
3.29
0.85
962
3.78
3.21
0.85
988
3.62
3.08
0.85
1030
4.22
3.08
0.73
946
4.06
2.97
0.73
998
3.97
2.90
0.73
1030
3.84
2.81
0.73
1082
4.35
2.65
0.61
998
4.22
2.57
0.61
1050
4.16
2.54
0.61
1082
4.03
2.46
0.61
1113
3.70
3.70
1.00
832
3.54
3.54
1.00
874
3.40
3.40
1.00
915
3.28
3.28
1.00
957
3.86
3.86
1.00
874
3.70
3.70
1.00
926
3.59
3.59
1.00
946
3.47
3.47
1.00
988
4.02
3.57
0.89
905
3.87
3.45
0.89
962
3.78
3.36
0.89
988
3.62
3.22
0.89
1030
4.22
3.25
0.77
946
4.06
3.13
0.77
998
3.97
3.06
0.77
1030
3.84
2.96
0.77
1082
4.35
2.83
0.65
998
4.22
2.74
0.65
1050
4.16
2.70
0.65
1082
4.03
2.62
0.65
1113
Q : Total capacity (kW)
SHC : Sensible heat capacity (kW)
OBH648A
SHF : Sensible heat factor
INPUT : Total power input (W)
19
DB : Dry-bulb temperature
WB : Wet-bulb temperature
PERFORMANCE DATA COOL operation at Rated frequency
MUZ-HJ35VA
CAPACITY: 3.15 kW
INDOOR INDOOR
DB (°C) WB (°C)
21
21
22
22
22
23
23
23
24
24
24
24
25
25
25
25
26
26
26
26
26
27
27
27
27
27
28
28
28
28
28
29
29
29
29
29
30
30
30
30
30
31
31
31
31
31
32
32
32
32
32
NOTE
18
20
18
20
22
18
20
22
18
20
22
24
18
20
22
24
18
20
22
24
26
18
20
22
24
26
18
20
22
24
26
18
20
22
24
26
18
20
22
24
26
18
20
22
24
26
18
20
22
24
26
Q
SHF: 0.87
INPUT: 1040 W
35
SHC SHF INPUT
OUTDOOR DB (°C)
40
Q
SHC SHF INPUT
Q
46
SHC SHF INPUT
3.09
2.13
0.69
1019
2.84
1.96
0.69
1082
2.61
1.80
0.69
3.24
1.85
0.57
1061
3.02
1.72
0.57
1113
2.80
1.60
0.57
1175
3.09
2.25
0.73
1019
2.84
2.07
0.73
1082
2.61
1.91
0.73
1123
3.24
1.98
0.61
1061
3.02
1.84
0.61
1113
2.80
1.71
0.61
1175
3.43
1.68
0.49
1102
3.21
1.57
0.49
1165
2.99
1.47
0.49
1206
3.09
2.38
0.77
1019
2.84
2.18
0.77
1082
2.61
2.01
0.77
1123
3.24
2.11
0.65
1061
3.02
1.97
0.65
1113
2.80
1.82
0.65
1175
3.43
1.82
0.53
1102
3.21
1.70
0.53
1165
2.99
1.59
0.53
1206
3.09
2.50
0.81
1019
2.84
2.30
0.81
1082
2.61
2.12
0.81
1123
3.24
2.24
0.69
1061
3.02
2.09
0.69
1113
2.80
1.93
0.69
1175
3.43
1.96
0.57
1102
3.21
1.83
0.57
1165
2.99
1.71
0.57
1206
3.62
1.63
0.45
1144
3.40
1.53
0.45
1196
3.21
1.45
0.45
1248
3.09
2.62
0.85
1019
2.84
2.41
0.85
1082
2.61
2.22
0.85
1123
3.24
2.37
0.73
1061
3.02
2.21
0.73
1113
2.80
2.05
0.73
1175
3.43
2.09
0.61
1102
3.21
1.96
0.61
1165
2.99
1.83
0.61
1206
3.62
1.78
0.49
1144
3.40
1.67
0.49
1196
3.21
1.57
0.49
1248
3.09
2.75
0.89
1019
2.84
2.52
0.89
1082
2.61
2.33
0.89
1123
3.24
2.50
0.77
1061
3.02
2.33
0.77
1113
2.80
2.16
0.77
1175
3.43
2.23
0.65
1102
3.21
2.09
0.65
1165
2.99
1.95
0.65
1206
3.62
1.92
0.53
1144
3.40
1.80
0.53
1196
3.21
1.70
0.53
1248
3.81
1.56
0.41
1186
3.59
1.47
0.41
1238
3.37
1.38
0.41
1290
3.09
2.87
0.93
1019
2.84
2.64
0.93
1082
2.61
2.43
0.93
1123
3.24
2.63
0.81
1061
3.02
2.45
0.81
1113
2.80
2.27
0.81
1175
3.43
2.37
0.69
1102
3.21
2.22
0.69
1165
2.99
2.06
0.69
1206
3.62
2.06
0.57
1144
3.40
1.94
0.57
1196
3.21
1.83
0.57
1248
3.81
1.72
0.45
1186
3.59
1.62
0.45
1238
3.37
1.52
0.45
1290
3.09
2.99
0.97
1019
2.84
2.75
0.97
1082
2.61
2.54
0.97
1123
3.24
2.76
0.85
1061
3.02
2.57
0.85
1113
2.80
2.38
0.85
1175
3.43
2.51
0.73
1102
3.21
2.35
0.73
1165
2.99
2.18
0.73
1206
3.62
2.21
0.61
1144
3.40
2.08
0.61
1196
3.21
1.96
0.61
1248
3.81
1.87
0.49
1186
3.59
1.76
0.49
1238
3.37
1.65
0.49
1290
3.09
3.09
1.00
1019
2.84
2.84
1.00
1082
2.61
2.61
1.00
1123
3.24
2.89
0.89
1061
3.02
2.69
0.89
1113
2.80
2.50
0.89
1175
3.43
2.64
0.77
1102
3.21
2.47
0.77
1165
2.99
2.30
0.77
1206
3.62
2.35
0.65
1144
3.40
2.21
0.65
1196
3.21
2.09
0.65
1248
3.81
2.02
0.53
1186
3.59
1.90
0.53
1238
3.37
1.79
0.53
1290
3.09
3.09
1.00
1019
2.84
2.84
1.00
1082
2.61
2.61
1.00
1123
3.24
3.02
0.93
1061
3.02
2.81
0.93
1113
2.80
2.61
0.93
1175
3.43
2.78
0.81
1102
3.21
2.60
0.81
1165
2.99
2.42
0.81
1206
3.62
2.50
0.69
1144
3.40
2.35
0.69
1196
3.21
2.22
0.69
1248
3.81
2.17
0.57
1186
3.59
2.05
0.57
1238
3.37
1.92
0.57
1290
3.09
3.09
1.00
1019
2.84
2.84
1.00
1082
2.61
2.61
1.00
1123
3.24
3.15
0.97
1061
3.02
2.93
0.97
1113
2.80
2.72
0.97
1175
3.43
2.92
0.85
1102
3.21
2.73
0.85
1165
2.99
2.54
0.85
1206
3.62
2.64
0.73
1144
3.40
2.48
0.73
1196
3.21
2.35
0.73
1248
3.81
2.33
0.61
1186
3.59
2.19
0.61
1238
3.37
2.06
0.61
1290
3.09
3.09
1.00
1019
2.84
2.84
1.00
1082
2.61
2.61
1.00
1123
3.24
3.24
1.00
1061
3.02
3.02
1.00
1113
2.80
2.80
1.00
1175
3.43
3.06
0.89
1102
3.21
2.86
0.89
1165
2.99
2.66
0.89
1206
3.62
2.79
0.77
1144
3.40
2.62
0.77
1196
3.21
2.47
0.77
1248
3.81
2.48
0.65
1186
3.59
2.33
0.65
1238
3.37
2.19
0.65
1290
Q : Total capacity (kW)
SHC : Sensible heat capacity (kW)
OBH648A
SHF : Sensible heat factor
INPUT : Total power input (W)
20
1123
DB : Dry-bulb temperature
WB : Wet-bulb temperature
PERFORMANCE DATA COOL operation at Rated frequency
MUZ-HJ50VA
CAPACITY: 5.0 kW
INDOOR INDOOR
DB (°C) WB (°C)
SHF: 0.70
INPUT: 2050 W
OUTDOOR DB (°C)
21
25
27
30
SHF
INPUT
21
18
5.88
3.06
0.52
1640
5.63
2.93
0.52
1722
5.40
2.81
0.52
1804
5.20
2.70
0.52
1886
21
20
6.13
2.45
0.40
1722
5.88
2.35
0.40
1825
5.70
2.28
0.40
1866
5.50
2.20
0.40
1948
22
18
5.88
3.29
0.56
1640
5.63
3.15
0.56
1722
5.40
3.02
0.56
1804
5.20
2.91
0.56
1886
22
20
6.13
2.70
0.44
1722
5.88
2.59
0.44
1825
5.70
2.51
0.44
1866
5.50
2.42
0.44
1948
22
22
6.38
2.04
0.32
1784
6.15
1.97
0.32
1896
6.00
1.92
0.32
1948
5.75
1.84
0.32
2030
23
18
5.88
3.53
0.60
1640
5.63
3.38
0.60
1722
5.40
3.24
0.60
1804
5.20
3.12
0.60
1886
23
20
6.13
2.94
0.48
1722
5.88
2.82
0.48
1825
5.70
2.74
0.48
1866
5.50
2.64
0.48
1948
23
22
6.38
2.30
0.36
1784
6.15
2.21
0.36
1896
6.00
2.16
0.36
1948
5.75
2.07
0.36
2030
24
18
5.88
3.76
0.64
1640
5.63
3.60
0.64
1722
5.40
3.46
0.64
1804
5.20
3.33
0.64
1886
24
20
6.13
3.19
0.52
1722
5.88
3.06
0.52
1825
5.70
2.96
0.52
1866
5.50
2.86
0.52
1948
24
22
6.38
2.55
0.40
1784
6.15
2.46
0.40
1896
6.00
2.40
0.40
1948
5.75
2.30
0.40
2030
24
24
6.70
1.88
0.28
1866
6.45
1.81
0.28
1968
6.30
1.76
0.28
2030
6.10
1.71
0.28
2132
25
18
5.88
4.00
0.68
1640
5.63
3.83
0.68
1722
5.40
3.67
0.68
1804
5.20
3.54
0.68
1886
25
20
6.13
3.43
0.56
1722
5.88
3.29
0.56
1825
5.70
3.19
0.56
1866
5.50
3.08
0.56
1948
25
22
6.38
2.81
0.44
1784
6.15
2.71
0.44
1896
6.00
2.64
0.44
1948
5.75
2.53
0.44
2030
25
24
6.70
2.14
0.32
1866
6.45
2.06
0.32
1968
6.30
2.02
0.32
2030
6.10
1.95
0.32
2132
26
18
5.88
4.23
0.72
1640
5.63
4.05
0.72
1722
5.40
3.89
0.72
1804
5.20
3.74
0.72
1886
26
20
6.13
3.68
0.60
1722
5.88
3.53
0.60
1825
5.70
3.42
0.60
1866
5.50
3.30
0.60
1948
26
22
6.38
3.06
0.48
1784
6.15
2.95
0.48
1896
6.00
2.88
0.48
1948
5.75
2.76
0.48
2030
26
24
6.70
2.41
0.36
1866
6.45
2.32
0.36
1968
6.30
2.27
0.36
2030
6.10
2.20
0.36
2132
26
26
6.90
1.66
0.24
1968
6.70
1.61
0.24
2071
6.60
1.58
0.24
2132
6.40
1.54
0.24
2194
27
18
5.88
4.47
0.76
1640
5.63
4.28
0.76
1722
5.40
4.10
0.76
1804
5.20
3.95
0.76
1886
27
20
6.13
3.92
0.64
1722
5.88
3.76
0.64
1825
5.70
3.65
0.64
1866
5.50
3.52
0.64
1948
27
22
6.38
3.32
0.52
1784
6.15
3.20
0.52
1896
6.00
3.12
0.52
1948
5.75
2.99
0.52
2030
27
24
6.70
2.68
0.40
1866
6.45
2.58
0.40
1968
6.30
2.52
0.40
2030
6.10
2.44
0.40
2132
27
26
6.90
1.93
0.28
1968
6.70
1.88
0.28
2071
6.60
1.85
0.28
2132
6.40
1.79
0.28
2194
28
18
5.88
4.70
0.80
1640
5.63
4.50
0.80
1722
5.40
4.32
0.80
1804
5.20
4.16
0.80
1886
28
20
6.13
4.17
0.68
1722
5.88
4.00
0.68
1825
5.70
3.88
0.68
1866
5.50
3.74
0.68
1948
28
22
6.38
3.57
0.56
1784
6.15
3.44
0.56
1896
6.00
3.36
0.56
1948
5.75
3.22
0.56
2030
28
24
6.70
2.95
0.44
1866
6.45
2.84
0.44
1968
6.30
2.77
0.44
2030
6.10
2.68
0.44
2132
28
26
6.90
2.21
0.32
1968
6.70
2.14
0.32
2071
6.60
2.11
0.32
2132
6.40
2.05
0.32
2194
29
18
5.88
4.94
0.84
1640
5.63
4.73
0.84
1722
5.40
4.54
0.84
1804
5.20
4.37
0.84
1886
29
20
6.13
4.41
0.72
1722
5.88
4.23
0.72
1825
5.70
4.10
0.72
1866
5.50
3.96
0.72
1948
29
22
6.38
3.83
0.60
1784
6.15
3.69
0.60
1896
6.00
3.60
0.60
1948
5.75
3.45
0.60
2030
29
24
6.70
3.22
0.48
1866
6.45
3.10
0.48
1968
6.30
3.02
0.48
2030
6.10
2.93
0.48
2132
29
26
6.90
2.48
0.36
1968
6.70
2.41
0.36
2071
6.60
2.38
0.36
2132
6.40
2.30
0.36
2194
30
18
5.88
5.17
0.88
1640
5.63
4.95
0.88
1722
5.40
4.75
0.88
1804
5.20
4.58
0.88
1886
30
20
6.13
4.66
0.76
1722
5.88
4.47
0.76
1825
5.70
4.33
0.76
1866
5.50
4.18
0.76
1948
30
22
6.38
4.08
0.64
1784
6.15
3.94
0.64
1896
6.00
3.84
0.64
1948
5.75
3.68
0.64
2030
30
24
6.70
3.48
0.52
1866
6.45
3.35
0.52
1968
6.30
3.28
0.52
2030
6.10
3.17
0.52
2132
30
26
6.90
2.76
0.40
1968
6.70
2.68
0.40
2071
6.60
2.64
0.40
2132
6.40
2.56
0.40
2194
31
18
5.88
5.41
0.92
1640
5.63
5.18
0.92
1722
5.40
4.97
0.92
1804
5.20
4.78
0.92
1886
31
20
6.13
4.90
0.80
1722
5.88
4.70
0.80
1825
5.70
4.56
0.80
1866
5.50
4.40
0.80
1948
31
22
6.38
4.34
0.68
1784
6.15
4.18
0.68
1896
6.00
4.08
0.68
1948
5.75
3.91
0.68
2030
31
24
6.70
3.75
0.56
1866
6.45
3.61
0.56
1968
6.30
3.53
0.56
2030
6.10
3.42
0.56
2132
31
26
6.90
3.04
0.44
1968
6.70
2.95
0.44
2071
6.60
2.90
0.44
2132
6.40
2.82
0.44
2194
32
18
5.88
5.64
0.96
1640
5.63
5.40
0.96
1722
5.40
5.18
0.96
1804
5.20
4.99
0.96
1886
32
20
6.13
5.15
0.84
1722
5.88
4.94
0.84
1825
5.70
4.79
0.84
1866
5.50
4.62
0.84
1948
32
22
6.38
4.59
0.72
1784
6.15
4.43
0.72
1896
6.00
4.32
0.72
1948
5.75
4.14
0.72
2030
32
24
6.70
4.02
0.60
1866
6.45
3.87
0.60
1968
6.30
3.78
0.60
2030
6.10
3.66
0.60
2132
32
26
6.90
3.31
0.48
1968
6.70
3.22
0.48
2071
6.60
3.17
0.48
2132
6.40
3.07
0.48
2194
NOTE
Q
SHC
SHF
INPUT
Q
SHC
SHF
INPUT
Q
SHC
SHF
INPUT
Q
SHC
Q : Total capacity (kW)
SHC : Sensible heat capacity (kW)
OBH648A
SHF : Sensible heat factor
INPUT : Total power input (W)
21
DB : Dry-bulb temperature
WB : Wet-bulb temperature
PERFORMANCE DATA COOL operation at Rated frequency
MUZ-HJ50VA
CAPACITY: 5.0 kW
INDOOR INDOOR
DB (°C) WB (°C)
SHF: 0.70
INPUT: 2050 W
OUTDOOR DB (°C)
35
40
46
SHF
INPUT
21
18
4.90
2.55
0.52
2009
4.50
2.34
0.52
2132
4.15
2.16
0.52
2214
21
20
5.15
2.06
0.40
2091
4.80
1.92
0.40
2194
4.45
1.78
0.40
2317
22
18
4.90
2.74
0.56
2009
4.50
2.52
0.56
2132
4.15
2.32
0.56
2214
22
20
5.15
2.27
0.44
2091
4.80
2.11
0.44
2194
4.45
1.96
0.44
2317
22
22
5.45
1.74
0.32
2173
5.10
1.63
0.32
2296
4.75
1.52
0.32
2378
23
18
4.90
2.94
0.60
2009
4.50
2.70
0.60
2132
4.15
2.49
0.60
2214
23
20
5.15
2.47
0.48
2091
4.80
2.30
0.48
2194
4.45
2.14
0.48
2317
23
22
5.45
1.96
0.36
2173
5.10
1.84
0.36
2296
4.75
1.71
0.36
2378
24
18
4.90
3.14
0.64
2009
4.50
2.88
0.64
2132
4.15
2.66
0.64
2214
24
20
5.15
2.68
0.52
2091
4.80
2.50
0.52
2194
4.45
2.31
0.52
2317
24
22
5.45
2.18
0.40
2173
5.10
2.04
0.40
2296
4.75
1.90
0.40
2378
24
24
5.75
1.61
0.28
2255
5.40
1.51
0.28
2358
5.10
1.43
0.28
2460
25
18
4.90
3.33
0.68
2009
4.50
3.06
0.68
2132
4.15
2.82
0.68
2214
25
20
5.15
2.88
0.56
2091
4.80
2.69
0.56
2194
4.45
2.49
0.56
2317
25
22
5.45
2.40
0.44
2173
5.10
2.24
0.44
2296
4.75
2.09
0.44
2378
25
24
5.75
1.84
0.32
2255
5.40
1.73
0.32
2358
5.10
1.63
0.32
2460
26
18
4.90
3.53
0.72
2009
4.50
3.24
0.72
2132
4.15
2.99
0.72
2214
26
20
5.15
3.09
0.60
2091
4.80
2.88
0.60
2194
4.45
2.67
0.60
2317
26
22
5.45
2.62
0.48
2173
5.10
2.45
0.48
2296
4.75
2.28
0.48
2378
26
24
5.75
2.07
0.36
2255
5.40
1.94
0.36
2358
5.10
1.84
0.36
2460
26
26
6.05
1.45
0.24
2337
5.70
1.37
0.24
2440
5.35
1.28
0.24
2542
27
18
4.90
3.72
0.76
2009
4.50
3.42
0.76
2132
4.15
3.15
0.76
2214
27
20
5.15
3.30
0.64
2091
4.80
3.07
0.64
2194
4.45
2.85
0.64
2317
27
22
5.45
2.83
0.52
2173
5.10
2.65
0.52
2296
4.75
2.47
0.52
2378
27
24
5.75
2.30
0.40
2255
5.40
2.16
0.40
2358
5.10
2.04
0.40
2460
27
26
6.05
1.69
0.28
2337
5.70
1.60
0.28
2440
5.35
1.50
0.28
2542
28
18
4.90
3.92
0.80
2009
4.50
3.60
0.80
2132
4.15
3.32
0.80
2214
28
20
5.15
3.50
0.68
2091
4.80
3.26
0.68
2194
4.45
3.03
0.68
2317
28
22
5.45
3.05
0.56
2173
5.10
2.86
0.56
2296
4.75
2.66
0.56
2378
28
24
5.75
2.53
0.44
2255
5.40
2.38
0.44
2358
5.10
2.24
0.44
2460
28
26
6.05
1.94
0.32
2337
5.70
1.82
0.32
2440
5.35
1.71
0.32
2542
29
18
4.90
4.12
0.84
2009
4.50
3.78
0.84
2132
4.15
3.49
0.84
2214
29
20
5.15
3.71
0.72
2091
4.80
3.46
0.72
2194
4.45
3.20
0.72
2317
29
22
5.45
3.27
0.60
2173
5.10
3.06
0.60
2296
4.75
2.85
0.60
2378
29
24
5.75
2.76
0.48
2255
5.40
2.59
0.48
2358
5.10
2.45
0.48
2460
29
26
6.05
2.18
0.36
2337
5.70
2.05
0.36
2440
5.35
1.93
0.36
2542
30
18
4.90
4.31
0.88
2009
4.50
3.96
0.88
2132
4.15
3.65
0.88
2214
30
20
5.15
3.91
0.76
2091
4.80
3.65
0.76
2194
4.45
3.38
0.76
2317
30
22
5.45
3.49
0.64
2173
5.10
3.26
0.64
2296
4.75
3.04
0.64
2378
30
24
5.75
2.99
0.52
2255
5.40
2.81
0.52
2358
5.10
2.65
0.52
2460
30
26
6.05
2.42
0.40
2337
5.70
2.28
0.40
2440
5.35
2.14
0.40
2542
31
18
4.90
4.51
0.92
2009
4.50
4.14
0.92
2132
4.15
3.82
0.92
2214
31
20
5.15
4.12
0.80
2091
4.80
3.84
0.80
2194
4.45
3.56
0.80
2317
31
22
5.45
3.71
0.68
2173
5.10
3.47
0.68
2296
4.75
3.23
0.68
2378
31
24
5.75
3.22
0.56
2255
5.40
3.02
0.56
2358
5.10
2.86
0.56
2460
31
26
6.05
2.66
0.44
2337
5.70
2.51
0.44
2440
5.35
2.35
0.44
2542
32
18
4.90
4.70
0.96
2009
4.50
4.32
0.96
2132
4.15
3.98
0.96
2214
32
20
5.15
4.33
0.84
2091
4.80
4.03
0.84
2194
4.45
3.74
0.84
2317
32
22
5.45
3.92
0.72
2173
5.10
3.67
0.72
2296
4.75
3.42
0.72
2378
32
24
5.75
3.45
0.60
2255
5.40
3.24
0.60
2358
5.10
3.06
0.60
2460
32
26
6.05
2.90
0.48
2337
5.70
2.74
0.48
2440
5.35
2.57
0.48
2542
NOTE
Q
SHC
SHF
INPUT
Q
SHC
SHF
INPUT
Q
SHC
Q : Total capacity (kW)
SHC : Sensible heat capacity (kW)
OBH648A
SHF : Sensible heat factor
INPUT : Total power input (W)
22
DB : Dry-bulb temperature
WB : Wet-bulb temperature
PERFORMANCE DATA HEAT operation at Rated frequency
MUZ-HJ25VA
CAPACITY: 3.15 kW
INDOOR
DB (°C)
15
21
26
-10
Q
INPUT
1.98
566
1.89
609
1.70
653
MUZ-HJ35VA
CAPACITY: 3.6 kW
INDOOR
DB (°C)
15
21
26
INPUT: 870 W
-5
Q
INPUT
2.39
679
2.27
722
2.11
766
OUTDOOR WB (°C)
0
5
10
Q
INPUT
Q
INPUT
Q
INPUT
2.80
766
3.21
827
3.62
879
2.68
800
3.06
861
3.47
905
2.49
844
2.90
905
3.31
948
Q
4.00
3.84
3.69
15
INPUT
905
931
974
Q
4.41
4.24
4.10
20
INPUT
922
966
1001
OUTDOOR WB (°C)
0
5
10
Q
INPUT
Q
INPUT
Q
INPUT
3.20
876
3.67
945
4.14
1005
3.06
915
3.49
985
3.96
1035
2.84
965
3.31
1035
3.78
1085
Q
4.57
4.39
4.21
15
INPUT
1035
1065
1114
Q
5.04
4.84
4.68
20
INPUT
1055
1104
1144
INPUT: 995 W
-10
Q
INPUT
2.27
647
2.16
697
1.94
746
-5
Q
INPUT
2.74
776
2.59
826
2.41
876
MUZ-HJ50VA
CAPACITY: 5.4 kW
INDOOR
DB (°C)
15
21
26
INPUT: 1480 W
OUTDOOR WB (°C)
-10
-5
0
5
10
15
20
Q
INPUT
Q
INPUT
Q
INPUT
Q
INPUT
Q
INPUT
Q
INPUT
Q
INPUT
3.40
3.24
2.92
962
1036
1110
4.10
3.89
3.62
1154
1228
1302
4.81
4.59
4.27
1302
1362
1436
5.51
5.24
4.97
1406
1465
1539
6.21
5.94
5.67
1495
1539
1613
6.86
6.59
6.32
1539
1584
1658
7.56
7.26
7.02
1569
1643
1702
NOTE Q: Total capacity (kW) INPUT : Total power input (W) DB: Dry-bulb temperature WB: Wet-bulb temperature
OBH648A
23
9
ACTUATOR CONTROL
MUZ-HJ25VA MUZ-HJ35VA MUZ-HJ50VA
9-1. OUTDOOR FAN MOTOR CONTROL
The fan motor turns ON/OFF, interlocking with the compressor.
[ON] The fan motor turns ON 5 seconds before the compressor starts up.
[OFF] The fan motor turns OFF 15 seconds after the compressor has stopped running.
5 seconds
15 seconds
ON
Compressor
OFF
ON
Outdoor fan
motor
OFF
9-2. R.V. COIL CONTROL
R.V. COIL CONTROL MUZ-HJ25VA MUZ-35VA
Heating . . . . . . . . . . . . . . . . . OFF
Cooling . . . . . . . . . . . . . . . . . ON
Dry . . . . . . . . . . . . . . . . . . . . ON
NOTE: The 4-way valve reverses for 5 seconds right before start-up of the compressor.
<COOL>
<HEAT>
5 seconds
5 seconds
Compressor
ON
OFF
R.V.coil
ON
OFF
Outdoor fan ON
OFF
motor
R.V. COIL CONTROL MUZ-HJ50VA
Heating . . . . . . . . . . . . . . . . . ON
Cooling . . . . . . . . . . . . . . . . . OFF
Dry . . . . . . . . . . . . . . . . . . . . OFF
NOTE: The 4-way valve reverses for 5 seconds right before start-up of the compressor.
<COOL>
Compressor
ON
OFF
R.V.coil
ON
OFF
<HEAT>
5 seconds
5 seconds
Outdoor fan ON
OFF
motor
9-3. RELATION BETWEEN MAIN SENSOR AND ACTUATOR
Actuator
Sensor
Discharge temperature thermistor
Indoor coil temperature thermistor
Defrost thermistor
Fin temperature thermistor
OBH648A
Purpose
Protection
Cooling: Coil frost prevention
Heating: High pressure protection
Cooling: High pressure protection
Heating: Defrosting
Protection
24
Compressor
LEV
○
○
○
○
○
○
○
○
○
Outdoor fan
motor
R.V. coil
Indoor fan
motor
○
○
○
○
○
10
SERVICE FUNCTIONS
MUZ-HJ25VA MUZ-HJ35VA MUZ-HJ50VA
10-1. CHANGE IN DEFROST SETTING
<JS> When the JS wire of the inverter P.C. board is cut/ soldered, the defrost finish temperature is changed. (Refer to
11-6-1.)
Jumper wire
JS
Soldered
(Initial setting)
None (Cut)
Defrost finish temperature (°C)
MUZ-HJ25/35VA
MUZ-HJ50VA
8
11
15
10-2. PRE-HEAT CONTROL SETTING
PRE-HEAT CONTROL
When moisture gets into the refrigerant cycle, it may interfere the start-up of the compressor at low discharge temperature. The pre-heat control prevents this interference. The pre-heat control turns ON when the discharge temperature is
20°C or below. When the pre-heat control turns ON, the compressor is energized. (About 50 W)
<JK> When the JK wire of the inverter P.C. board is cut, pre-heat control is activated. (Refer to 11-6.1)
NOTE : When the inverter P.C. board is replaced, check the Jumper wires, and cut/solder them if necessary.
11
TROUBLESHOOTING
MUZ-HJ25VA MUZ-HJ35VA MUZ-HJ50VA
11-1. CAUTIONS ON TROUBLESHOOTING
1. Before troubleshooting, check the following:
1) Check the power supply voltage.
2) Check the indoor/outdoor connecting wire for miswiring.
2. Take care of the following during servicing
1) Before servicing the air conditioner, be sure to turn OFF the main unit first with the remote controller, and then after
confirming the horizontal vane is closed, turn OFF the breaker and/or disconnect the power plug.
2) Be sure to turn OFF the power supply before removing the front panel, the cabinet, the top panel, and the electronic
control P.C. board.
3) When removing the electrical parts, be careful to the residual voltage of smoothing capacitor.
4) When removing the electronic control P.C. board, hold the edge of the board with care NOT to apply stress on the
components.
5) When connecting or disconnecting the connectors, hold the housing of the connector. DO NOT pull the lead wires.
<Incorrect>
<Correct>
Lead wiring
Housing point
3. Troubleshooting procedure
1) Check if the OPERATION INDICATOR lamp on the indoor unit is flashing on and off to indicate an abnormality. To
make sure, check how many times the OPERATION INDICATOR lamp is flashing on and off before starting service
work.
2) Before servicing, check that the connector and terminal are connected properly.
3) When the electronic control P.C. board seems to be defective, check the copper foil pattern for disconnection and the
components for bursting and discoloration.
4) Refer to 11-2 and 11-3.
OBH648A
25
11-2. FAILURE MODE RECALL FUNCTION
Outline of the function
This air conditioner can memorize the abnormal condition which has occurred once.
Even though LED indication listed on the troubleshooting check table (11-3.) disappears, the memorized failure details
can be recalled.
This mode is very useful when the unit needs to be repaired for the abnormality which does not recur.
1. Flow chart of failure mode recall function for the indoor/outdoor unit
Operational procedure
The cause of abnormality cannot be found because the abnormality does not recur.
Setting up the failure mode recall function
Turn ON the power supply.
<Preparation of the remote controller>
While pressing both OPERATION SELECT button and TOO COOL button on the
remote controller at the same time, press RESET button.
First, release RESET button.
Hold down the other two buttons for another 3 seconds. Make sure that the indicators
on the LCD screen shown in the right figure are all displayed. Then release the buttons.
Press OPERATE/STOP (ON/OFF) button of the remote controller (the set temperature is
displayed) with the remote controller headed towards the indoor unit. 1
1. Regardless of normal or abnormal condition, a short
beep is emitted once the signal is received.
Does the upper lamp of OPERATION INDICATOR lamp on the
indoor unit blink at the interval of 0.5 seconds?
Blinks: Either indoor or outdoor unit is abnormal. Beep is
emitted at the same timing as the blinking of the upper
lamp of OPERATION INDICATOR lamp. 2
Indoor unit is normal.
But the outdoor unit might be abnormal because there are some abnormalities that can't be recalled with this way.
Confirm if outdoor unit is abnormal according to the detailed outdoor
unit failure mode recall function. (Refer to 11-2.2)
No
(OFF)
Yes
(Blinks)
Judgment of indoor/outdoor abnormality
Before blinking, does the upper lamp of OPERATION INDICATOR lamp stay ON for 3 seconds?
Stays ON for 3 seconds (without beep):
The outdoor unit is abnormal.
No
Yes
The outdoor unit is abnormal.
Check the blinking pattern, and confirm the abnormal point with the
outdoor unit failure mode table. (Refer to 11-2.3)
3
Make sure to check at least two consecutive blinking cycles.
The indoor unit is abnormal.
Check the blinking pattern, and identify the abnormal point with the indoor unit
failure mode table. (Refer to indoor unit service manual.)
2
Make sure to check at least two consecutive blinking cycles.
Releasing the failure mode recall function
Release the failure mode recall function by the following procedures.
Turn OFF the power supply and turn it ON again.
Press RESET button of the remote controller.
Repair the failure parts.
Deleting the memorized abnormal condition
After repairing the unit, recall the failure mode again according to "Setting up the failure mode recall
function" mentioned above.
Press OPERATE/STOP (ON/OFF) button of the remote controller (the set temperature is displayed)
with the remote controller headed towards the indoor unit.
Press EMERGENCY OPERATION switch so that the memorized abnormal condition is deleted.
Release the failure mode recall function according to "Releasing the failure mode recall function"
mentioned above.
NOTE: 1. Make sure to release the failure mode recall function after it is set up, otherwise the unit cannot operate properly.
2. If the abnormal condition is not deleted from the memory, the last abnormal condition is kept memorized.
2. Blinking pattern when the indoor unit is abnormal:
Blinking at 0.52.5-second OFF second interval
Blinking at 0.52.5-second OFF second interval
ON
OFF
Beeps
Repeated cycle
Beeps
Repeated cycle
Beeps
Repeated cycle
3.Blinking pattern when the outdoor unit is abnormal:
Blinking at 0.52.5-second OFF
3-second ON
second interval
2.5-second OFF
3-second ON
Blinking at 0.5second interval
ON
OFF
No beep
Repeated cycle
OBH648A
Beeps
No beep
Repeated cycle
26
Beeps
Repeated cycle
2. Flow chart of the detailed outdoor unit failure mode recall function
Operational procedure
The outdoor unit might be abnormal.
Check if outdoor unit is abnormal according to the following procedures.
Make sure that the remote controller is set to the failure mode recall function.
With the remote controller headed towards the indoor unit, press TOO
COOL or TOO WARM button to adjust the set temperature to 25°C. 1
Does the upper lamp of OPERATION INDICATOR
lamp on the indoor unit blink at the interval of 0.5
seconds?
Blinks: The outdoor unit is abnormal. Beep is emitted
at the same timing as the blinking of the upper
lamp of OPERATION INDICATOR lamp. 2
Yes
(Blinks)
1. Regardless of normal or abnormal condition, 2 short
beeps are emitted as the signal is received.
No
(OFF)
The outdoor unit is abnormal.
Check the blinking pattern, and identify the abnormal point with the outdoor unit failure mode table (11-2.3.).
Make sure to check at least two consecutive blinking cycles. 2
The outdoor unit is normal.
Releasing the failure mode recall function
Release the failure mode recall function by the following procedures.
Turn OFF the power supply and turn it ON again.
Press RESET button of the remote controller.
Release the failure mode recall function according to the left mentioned procedure.
Repair the failure parts.
Deleting the memorized abnormal condition
After repairing the unit, recall the failure mode again according to "Setting up the failure mode recall
function" (11-2.1.).
Press OPERATE/STOP (ON/OFF) button of the remote controller (the set temperature is displayed) with
the remote controller headed towards the indoor unit.
Press EMERGENCY OPERATION switch so that the memorized abnormal condition is deleted.
Release the failure mode recall function according to "Releasing the failure mode recall function" mentioned above.
NOTE: 1. Make sure to release the failure mode recall function after it is set up, otherwise the unit cannot operate properly.
2. If the abnormal condition is not deleted from the memory, the last abnormal condition is kept memorized.
2.Blinking pattern when outdoor unit is abnormal:
2.5-second OFF
3-second ON
Blinking at 0.5second interval
2.5-second OFF
3-second ON
Blinking at 0.5second interval
ON
OFF
No beep
Repeated cycle
OBH648A
No beep
Repeated cycle
Beeps
27
Beeps
Repeated cycle
3. Outdoor unit failure mode table
The upper
lamp of
OPERATION
INDICATOR
lamp
(Indoor unit)
Abnormal point
(Failure mode/protection)
LED indication
(Outdoor P.C. board)
OFF
None (Normal)
1-time flash
2.5 seconds
OFF
Indoor/outdoor
communication, receiving
error
—
Indoor/outdoor
communication, receiving
error
—
Outdoor power system
3-time flash
2.5 seconds
OFF
Discharge temperature
thermistor
Defrost thermistor
1-time flash every
2.5 seconds
Fin temperature thermistor
3-time flash
2.5 seconds OFF
P.C. board temperature
thermistor
4-time flash
2.5 seconds OFF
4-time flash
2.5 seconds
OFF
—
Compressor synchronous
abnormality (Compressor
start-up failure protection)
5-time flash
2.5 seconds
OFF
Discharge temperature
6-time flash
2.5 seconds
OFF
High pressure
7-time flash
2.5 seconds
OFF
Fin temperature/ P.C. board
temperature
Outdoor fan motor
8-time flash
2.5 seconds
OFF
MUZ-HJ50VA
Nonvolatile memory data
9-time flash
2.5 seconds
OFF
Power module
Remedy
—
—
—
2-time flash
2.5 seconds
OFF
Outdoor heat exchanger
temperature thermistor
MUZ-HJ50VA
Overcurrent
Condition
Indoor/outdoor
Outdoor unit
unit failure
failure mode
mode recall
recall function
function
•Refer to 11-5. How
Any signals from the inverter P.C.
board cannot be received normally for to check miswiring and
3 minutes.
serial signal error.
Although the inverter P.C. board sends
signal "0", signal "1" has been received
30 consecutive times.
Overcurrent protection cut-out
operates 3 consecutive times within
1 minute after the compressor gets
started.
Thermistor shorts or opens during
compressor running.
•Refer to 11-5. How
to check miswiring and
serial signal error.
• Reconnect
connectors.
• Refer to 11-5. "How
to check inverter/
compressor".
• Check stop valve.
• Refer to 11-5.
"Check of outdoor
thermistors".
Defective outdoor
thermistors can be
identified by checking
the blinking pattern of
LED.
—
○
○
○
○
○
○
—
○
—
○
—
○
—
11-time flash
2.5 seconds OFF
12-time flash
2.5 seconds OFF
Large current flows into power module. • Reconnect
compressor connector.
• Refer to 11-5. "How
to check inverter/
compressor".
• Check stop valve.
• Reconnect
Waveform of compressor current is
distorted.
compressor connector.
• Refer to 11-5. "How
to check inverter/
compressor".
—
Temperature of discharge temperature
thermistor exceeds 116°C, compressor
stops.
Compressor can restart if discharge
temperature thermistor reads 100°C or
less 3 minutes later.
• Check refrigerant
circuit and refrigerant
amount.
• Refer to 11-5. "Check
of LEV".
—
Temperature indoor coil thermistor
exceeds 70°C in HEAT mode.
Temperature defrost thermistor
exceeds 70°C in COOL mode.
• Check refrigerant
circuit and refrigerant
amount.
• Check stop valve.
—
○
Temperature of fin temperature
thermistor on the inverter P.C. board
exceeds 80 °C (HJ25/35)/75 °C (HJ50),
or temperature of P.C. board temperature
thermistor on the inverter P.C. board
exceeds 78 °C (HJ25/35)/80 °C (HJ50).
• Check around outdoor
unit.
• Check outdoor unit air
passage.
• Refer to 11-5. "Check
of outdoor fan motor".
—
○
Outdoor fan has stopped 3 times in a
row within 30 seconds after outdoor
fan start-up.
• Refer to 11-5. "Check
of outdoor fan motor".
Refer to 11-5. "Check
of inverter P.C. board".
• Replace the inverter
P.C. board.
—
○
○
○
—
○
—
○
○
○
7-time flash
2.5 seconds OFF
—
5-time flash
2.5 seconds OFF
Nonvolatile memory data cannot be
read properly.
6-time flash
2.5 seconds OFF
10-time flash
2.5 seconds
OFF
Discharge temperature
11-time flash
2.5 seconds
OFF
DC voltage
8-time flash
2.5 seconds OFF
Each phase current of
compressor
9-time flash
2.5 seconds OFF
The interface short circuit occurs in the • Refer to 11-5. "How
output of the power module (IC700).
to check inverter/
The compressor winding shorts circuit. compressor".
Temperature of discharge temperature • Refer to 11-5. "Check
of LEV".
thermistor has been 50°C or less for
• Check refrigerant
20 minutes.
circuit and refrigerant
amount.
• Refer to 11-5. "How
DC voltage of inverter cannot be
detected normally.
to check inverter/
compressor".
Each phase current of compressor
cannot be detected normally.
14-time flash
2.5 seconds
OFF
Stop valve (Closed valve)
14-time flash
2.5 seconds OFF
Closed valve is detected by
compressor current.
• Check stop valve.
4-way valve/
Pipe temperature
16-time flash
2.5 seconds OFF
The 4-way valve does not work
properly.
The indoor coil thermistor detects an
abnormal temperature.
• Check 4-way valve.
• Replace inverter P.C.
board.
—
NOTE: Blinking patterns of this mode differ from the ones of TROUBLESHOOTING CHECK TABLE (11-3.).
OBH648A
—
28
11-3. TROUBLESHOOTING CHECK TABLE
No.
1
Symptom
Outdoor unit
does not operate.
Abnormal point/
Condition
1-time flash every Outdoor power sys2.5 seconds
tem
LED indication
2
3
6-time flash
2.5 seconds OFF
11-time flash
2.5 seconds OFF
14-time flash
2.5 seconds OFF
4
5
6
7
8
9
Condition
Remedy
Overcurrent protection cut-out operates 3 consecutive times
• Reconnect connector of compreswithin 1 minute after the compressor gets started, or failure of sor.
restart of compressor has repeated 24 times.
• Refer to 11-5. "How to check inverter/compressor".
• Check stop valve.
Outdoor thermistors Discharge temperature thermistor, fin temperature thermistor, • Refer to 11-5. "Check of outdoor
defrost thermistor, P.C. board temperature thermistor or outthermistors".
door heat exchanger temperature thermistor shorts or opens
during compressor running.
Outdoor control sys- Nonvolatile memory data cannot be read properly.
• Replace inverter P.C. board.
tem
(The upper lamp of OPERATION INDICATOR lamp of the indoor unit lights up or flashes 7-time.)
Serial signal
The communication fails between the indoor and outdoor unit • Refer to 11-5. "How to check
for 3 minutes.
miswiring and serial signal error.
Stop valve/
Closed valve is detected by compressor current.
• Check stop valve.
Closed valve
Outdoor unit
Outdoor unit is defective.
• Refer to 11-2.2. "Flow chart of the
(Other abnormality)
detailed outdoor unit failure mode
recall function".
16-time flash
4-way valve/
The 4-way valve does not work properly.
2.5 seconds OFF Pipe temperature
The indoor coil thermistor detects an abnormal temperature.
'Outdoor unit 2-time flash
Overcurrent protec- Large current flows into power module.
stops and
2.5 seconds OFF tion
When overcurrent protection occurs within 10 seconds after
restarts 3
compressor starts, compressor restarts after 15 seconds.
minutes later'
is repeated.
3-time flash
Discharge tempera- Temperature of discharge temperature thermistor exceeds
116 °C, compressor stops. Compressor can restart if discharge
2.5 seconds OFF ture overheat protemperature thermistor reads 100°C or less 3 minutes later.
tection
4-time flash
2.5 seconds OFF
10
Fin temperature
/P.C. board temperature thermistor
overheat protection
High pressure protection
Temperature of fin temperature thermistor on the heat sink
exceeds 80 °C (HJ25/35)/75 °C (HJ50) or temperature of P.C.
board temperature thermistor on the inverter P.C. board exceeds 78 °C (HJ25/35)/80 °C (HJ50).
Indoor coil thermistor exceeds 70°C in HEAT mode. Defrost
thermistor exceeds 70 °C in COOL mode.
11
5-time flash
2.5 seconds OFF
12
8-time flash
2.5 seconds OFF
Compressor synThe waveform of compressor current is distorted.
chronous abnormality
10-time flash
2.5 seconds OFF
MUZ-HJ50VA
Outdoor fan motor
13
Outdoor fan has stopped 3 times in a row within 30 seconds
after outdoor fan start-up.
12-time flash
2.5 seconds OFF
13-time flash
2.5 seconds OFF
1-time flash
2.5 seconds OFF
3-time flash
2.5 seconds OFF
Each phase current
of compressor
DC voltage
Each phase current of compressor cannot be detected normally.
DC voltage of inverter cannot be detected normally.
Frequency drop by
current protection
Frequency drop by
high pressure protection
When the input current exceeds 5.4 A (HJ25)/6.1 A (HJ35)/
9.2 A (HJ50), compressor frequency lowers.
Temperature of indoor coil thermistor exceeds 55 °C in HEAT
mode, compressor frequency lowers.
Frequency drop by
defrosting in COOL
mode
Indoor coil thermistor reads 8 °C or less in COOL mode, compressor frequency lowers.
4-time flash
2.5 seconds OFF
Frequency drop by
discharge temperature protection
Temperature of discharge temperature thermistor exceeds
111 °C, compressor frequency lowers.
5-time flash
2.5 seconds OFF
7-time flash
2.5 seconds OFF
Outside temperature
thermistor protection
Low discharge temperature protection
When the outside temperature thermistor shorts or opens,
protective operation without that thermistor is performed.
Temperature of discharge temperature thermistor has been
50°C or less for 20 minutes.
8-time flash
2.5 seconds OFF
PAM protection
PAM: Pulse Amplitude Modulation
The overcurrent flows into IC821 (Switching power transistor)
(HJ25/35)/IC820 (Power module) (HJ50) or the bus-bar voltage reaches 320 V or more, PAM stops and restarts.
9-time flash
2.5 seconds OFF
Inverter check mode The connector of compressor is disconnected, inverter check
mode starts.
14
15
16
Outdoor unit
operates.
17
18
19
20
Outdoor unit
operates.
21
22
The flashing frequency shows the number of times the LED blinks after every 2.5-second OFF.
(Example) When the flashing frequency is “2”.
2.5-second OFF
OBH648A
• Check around outdoor unit.
• Check outdoor unit air passage.
• Refer to 11-5. "Check of outdoor
fan motor".
• Check refrigerant circuit and refrigerant amount.
• Check stop valve.
• Reconnect connector of compressor.
• Refer to 11-5. "How to check inverter/compressor".
• Refer to 11-5. "Check of outdoor
fan motor.
• Refer to 11-5. "Check of inverter
P.C. board.
• Refer to 11-5. "How to check inverter/compressor".
• Refer to 11-5. "How to check inverter/compressor".
The unit is normal, but check the
following.
• Check if indoor filters are clogged.
• Check if refrigerant is short.
• Check if indoor/outdoor unit air
circulation is short cycled.
• Check refrigerant circuit and refrigerant amount.
• Refer to 11-5. "Check of LEV".
• Refer to 11-5. "Check of outdoor
thermistors".
• Refer to 11-5. Check of outdoor
thermistors.
• Refer to 11-5. "Check of LEV".
• Check refrigerant circuit and refrigerant amount.
This is not malfunction. PAM protection will be activated in the following cases:
1 Instantaneous power voltage
drop. (Short time power failure)
2 When the power supply voltage
is high.
• Check if the connector of the compressor is correctly connected.
Refer to 11-5. "How to check
inverter/compressor".
LED
0.5-second ON
0.5-second ON
OFF
• Check refrigerant circuit and refrigerant amount.
• Refer to 11-5. "Check of LEV".
Inverter P.C. board
MUZ-HJ25/35
NOTE: 1. The location of LED is illustrated at the right figure. Refer to 11-6.1.
2. LED is lighted during normal operation.
ON
• Refer to 11-5. "Check of R.V. coil".
• Replace inverter P.C. board.
• Reconnect connector of compressor.
• Refer to 11-5. "How to check inverter/compressor".
• Check stop valve.
2.5-second OFF
29
←
Flashing
Inverter P.C. board
MUZ-HJ50
LED
←
Flashing
11-4. TROUBLE CRITERION OF MAIN PARTS
MUZ-HJ25VA MUZ-HJ35VA MUZ-HJ50VA
Part name
Check method and criterion
Figure
Measure the resistance with a tester.
Defrost thermistor
(RT61)
Refer to 11-6. “Test point diagram and voltage”, 1. “Inverter P.C.
board”, for the chart of thermistor.
Measure the resistance with a tester.
Discharge temperature
Before measurement, hold the thermistor with your hands to warm it up.
thermistor (RT62)
Fin temperature thermistor
Refer to 11-6. “Test point diagram and voltage”, 1. “Inverter P.C.
(RT64)
board”, for the chart of thermistor.
Measure the resistance between the terminals with a tester.
(Part temperature -10 ~ 40°C)
Normal
Compressor (MC)
MUZ-HJ25VA
MUZ-HJ35VA
Outdoor fan motor (MF)
INNER FUSE
RA6V21-AB
152 +0
-5 °C CUT OFF
RA6V21-BB
126 ± 2: CUT OFF
U-V
U-W
V-W
WHT
2
MUZ-HJ25VA
MUZ-HJ35VA
MUZ-HJ50VA
2.01 ~ 2.86 Ω
1.20 ~ 1.72 Ω
0.78 ~ 1.11 Ω
RED BLK
3
1
W
V
U
Measure the resistance between the terminals with a tester.
(Part temperature -10 ~ 40°C)
MUZ-HJ25VA MUZ-HJ35VA
Color of lead wire
WHT – BLK
BLK – RED
Normal
RA6V21-AB
RA6V21-BB, BD
305 ~ 374 Ω
222 ~ 272 Ω
247 ~ 304 Ω
245 ~ 300 Ω
MUZ-HJ50VA
Color of lead wire
RED – BLK
BLK – WHT
WHT – RED
MUZ-HJ50VA
Outdoor fan motor (MF)
FUSE
BLK
WHT
Normal
RED WHT
RED BLK
W
30 ~ 43 Ω
V
U
Measure the resistance between the terminals with a tester.
(Part temperature -10˚C ~ 40°C)
Normal
MUZ-HJ25VA/35VA
MUZ-HJ50VA
1.19 ~ 1.78 kΩ
1.41 ~ 2.00 kΩ
Measure the resistance using a tester.
(Part temperature: -10 ~ 40°C)
MUZ-HJ35VA
Expansion valve coil (LEV)
OBH648A
Color of lead wire
WHT – RED
RED – ORN
YLW – BRN
BRN – BLU
Normal
37 ~ 54 Ω
30
LEV
ORN
RED
(+12V)
BLU
37 ~ 54
WHT
WHT
LEV
RED
ORN
BLU
Normal (Ω)
YLW
Color of lead wire
RED – ORN
RED – WHT
RED – BLU
RED – YLW
MUZ-HJ25VA
MUZ-HJ50VA
Expansion valve coil (LEV)
YLW
Measure the resistance using a tester.
(Temperature: -10 ~ 40°C)
BRN
R.V. coil (21S4)
11-5. TROUBLESHOOTING FLOW
A How to check inverter/compressor
Disconnect the connector (CN61) between
compressor and the power module (IC700).
See 11-5.
Check the voltage between terminals.
Are the voltages balanced?
Yes
Check the compressor.
No
“Check of open phase”.
Replace the inverter P.C. board.
See 11-5.
“Check of compressor”.
B Check of open phase
● With the connector between the compressor and the power module disconnected, activate the inverter and check if the inverter is normal by measuring the balance of voltage between the terminals.
Output voltage is 50 - 130 V. (The voltage may differ according to the tester.)
<< Operation method>>
Start cooling or heating operation by pressing EMERGENCY OPERATION switch on the indoor unit. (TEST RUN OPERATION : Refer to 8-3.)
<<Measurement point>>
At 3 points
BLK (U)-WHT (V)
Measure AC voltage between the lead wires at 3 points.
BLK (U)-RED (W)
WHT(V)-RED (W)
NOTE : 1. Output voltage varies according to power supply voltage.
2. Measure the voltage by analog type tester.
3. During this check, LED of the inverter P.C. board flashes 9 times. (Refer to 11-6.1.)
OBH648A
31
C Check of compressor
Refer to 11-5. “Check of compressor
winding”.
Is the compressor normal?
Yes
Refer to 11-5. “Check of compressor
operation time”.
Does the compressor operate continuously?
Yes
No
No
Replace the compressor.
Refer to 11-5.
“Check of compressor start failure”.
OK.
D Check of compressor winding
● Disconnect the connector (CN61) between the compressor and power module, and measure the resistance between the compressor terminals.
<<Measurement point>>
At 3 points
BLK-WHT
Measure the resistance between the lead wires at 3 points.
BLK-RED
WHT-RED
<<Judgement>>
Refer to 11-4.
0 [Ω] ················Abnormal [short]
Infinite [Ω] ·······Abnormal [open]
NOTE : Be sure to zero the ohmmeter before measurement.
E Check of compressor operation time
<<Judgement>>
● Connect the compressor and activate the inverter. Then measure
the time until the inverter stops due to over current.
<<Operation method>>
Start heating or cooling operation by pressing EMERGENCY
OPERATION switch on the indoor unit.
(TEST RUN OPERATION: Refer to 8-3.)
<<Measurement>>
Measure the time from the start of compressor to the stop of
compressor due to overcurrent.
0 second
Compressor starts
1 second
Abnormal
(IC700 failure)
(Compressor winding short)
2 seconds
Abnormal
(Compressor lock out)
(Starting defect)
10 seconds
Abnormal
(Poor contact,)
(Outdoor P.C. board defect)
(Disconnected connector)
Abnormal
(Refrigerant circuit defect)
(Closed valve)
10 minutes
OBH648A
32
Normal
F Check of compressor start failure
Make sure that ~ is normal.
•Electrical circuit check
. Contact of the compressor connector (Including CN61)
. Output voltage of inverter P.C. board and balance of them (See 11-5. )
. Direct current voltage between DB61(+) and (-) on the inverter P.C. board
. Voltage between outdoor terminal block S1-S2
Does the compressor run for 10 seconds or
more after it starts?
Yes
Check the refrigerant circuit.
Check the stop valve.
No
After the compressor is heated with a drier,
does the compressor start? 1
No
Replace the compressor.
Yes
1
Heat the compressor with
a drier for about 20 minutes.
Do not recover refrigerant
gas while heating.
Compressor start failure. Activate pre-heat control.
(Refer to 10-2. "PRE-HEAT CONTROL SETTING")
Heating part
G Check of outdoor thermistors
Disconnect the connector of thermistor in the inverter P.C. board (see
below table), and measure the resistance of thermistor.
Is the thermistor normal? (Refer to 11-6.1.)
Yes
No
Replace the thermistor except RT64. When RT64
is abnormal, replace the inverter P.C. board.
Reconnect the connector of thermistor.
Turn ON the power supply and press EMERGENCY OPERATION switch.
Does the unit operate for 10 minutes or more
without showing thermistor abnormality?
Yes
No
Replace the inverter P.C. board.
OK.
(Cause is poor contact.)
Thermistor
Defrost
Discharge temperature
Fin temperature
Outdoor heat exchanger temperature
Symbol
RT61
RT62
RT64
RT68
Connector, Pin No.
Between CN641 pin 1 and pin 2
Between CN641 pin 3 and pin 4
Between CN642 pin 1 and pin 2
Between CN644 pin 1 and pin 3
MUZ-HJ50VA only.
OBH648A
33
Board
Inverter P.C. board
H Check of R.V. coil
First of all, measure the resistance of R.V. coil to check if the coil is defective. Refer to 11-4.
In case CN721 is not connected or R.V. coil is open, voltage is generated between the terminal pins of the connector
although any signal is not being transmitted to R.V. coil.
Check if CN721 is connected.
MUZ-HJ25VA MUZ-HJ35VA
Unit operates COOL mode even if it is set to HEAT mode.
Disconnect connector (CN61)
between the compressor and the
power module.
Turn ON the power supply and
press EMERGENCY OPERATION
switch once (COOL mode).
Is there 230 VAC between CN721 and
on the inverter P.C. board 3 minutes
after the power supply is turned ON?
No
Replace the inverter
P.C. board.
Yes
Replace the 4-way valve.
Unit operates HEAT mode even if it is set to COOL mode.
Disconnect connector (CN61)
between the compressor and the
power module.
Turn ON the power supply and press
EMERGENCY OPERATION switch
twice (HEAT mode).
Is there 230 VAC between CN721 and
on the inverter P.C. board 3 minutes
after the power supply is turned ON?
Replace the inverter
Yes P.C. board.
No
Replace the 4-way valve.
MUZ-HJ50VA
Unit operates COOL mode even if it is set to HEAT mode.
Disconnect connector (CN61)
between the compressor and the
power module.
Turn ON the power supply and press
EMERGENCY OPERATION switch
twice (HEAT mode).
Is there 230 VAC between CN721 and
on the inverter P.C. board 3 minutes
after the power supply is turned ON?
No
Replace the inverter
P.C. board.
Yes
Replace the 4-way valve.
Unit operates HEAT mode even if it is set to COOL mode.
Disconnect connector (CN61)
between the compressor and the
power module.
Turn ON the power supply and
press EMERGENCY OPERATION
switch once (COOL mode).
Is there 230 VAC between CN721 and
on the inverter P.C. board 3 minutes
after the power supply is turned ON?
No
Replace the 4-way valve.
OBH648A
34
Replace the inverter
Yes P.C. board.
I Check of outdoor fan motor
MUZ-HJ25VA MUZ-HJ35VA
Check the resistance of fan motor. (Refer to
11-4.)
Is the resistance of
fan motor normal?
Yes
Replace the outdoor
fan motor.
No
Disconnect the connector CN771 on the
inverter P.C. board.
Disconnect the connector (CN61) between
compressor and power transistor module.
Turn ON the power supply and press the
EMERGENCY OPERATION switch.
After 3 minutes, is
there voltage 230 VAC
between CN771 and
on the inverter P.C.
board?
Yes
Does the upper lamp of
OPERATION
INDICATOR lamp on
the indoor unit light up?
No
Replace the inverter
P.C. board.
Replace the outdoor
fan motor.
MUZ-HJ50VA
Disconnect the connectors CN931
and CN932 from the inverter P.C.
board.
Check the connection between the
connector CN931 and CN932.
Is the resistance between each terminal of outdoor fan motor normal?
(Refer to 11-4.)
No
Yes
Disconnect CN932 from the inverter P.C. board, and turn on the
power supply.
Rotate the outdoor fan motor manually and measure the voltage
of CN931.
Between 1(+) and 5(-)
Between 2(+) and 5(-)
Between 3(+) and 5(-)
(Fixed to either 5 or 0 VDC)
No
No
Does the voltage between each terminal become 5 and 0
VDC repeatedly?
Yes
Does the outdoor fan motor rotate smoothly?
Yes
Replace the inverter P.C. board.
Replace the outdoor fan motor.
OBH648A
35
250 - 370 VDC
J Check of power supply
DB61
Disconnect the connector (CN61)
between compressor and power
module.
Turn ON power supply and press
EMERGENCY OPERATION switch.
Rectify indoor/outdoor
connecting wire.
Does the upper lamp of OPERATION
INDICATOR lamp on the indoor unit
light up?
Yes
No
Is there voltage 250 - 370 VDC
between DB61 (+) and DB61 (–) on
the inverter P.C. board?
(Refer to 11-6.1.)
No
Yes
Yes
Is there voltage 230 VAC
between the indoor terminal
block S1 and S2?
Does LED on the inverter P.C.
board light up or flash? (Refer
to 11-6.1.)
Yes
Inverter P.C. board
(Solder side)
No
No
Replace the indoor
electronic control P.C.
board.
Replace the inverter
P.C. board.
If light up, OK.
If flash, refer to 11-3.
Check the electric parts in main circuit.
K Check of LEV (Expansion valve)
Turn ON the power supply.
<Preparation of the remote controller>
While pressing both OPERATION SELECT button
and TOO COOL button on the remote controller at the
same time, press RESET button.
First, release RESET button.
Hold down the other two buttons for another 3
seconds. Make sure that the indicators on the LCD
screen shown in the right figure are all displayed.
Then release the buttons.
Press OPERATE/STOP (ON/OFF) button of the remote
controller (the set temperature is displayed) with the
remote controller headed towards the indoor unit. 1
Expansion valve operates in full-opening direction.
Do you hear the expansion valve "click,
click·······"?
Do you feel the expansion valve vibrate
on touching it ?
No
Is LEV coil properly fixed to
the expansion valve?
No
Yes
Does the resistance of LEV
coil have the characteristics? Yes
(Refer to 11-4.)
No
Replace the LEV coil.
1. Regardless of normal or abnormal condition, a short beep
is emitted once the signal is received.
Yes
OK
Properly fix the LEV coil to the expansion valve.
Measure each voltage between connector
pins of CN724 on the inverter P.C. board.
1. Pin (-) — Pin (+)
2. Pin (-) — Pin (+)
3. Pin (-) — Pin (+)
4. Pin (-) — Pin (+)
Is there about 3 ~ 5 VAC between each?
NOTE: Measure the voltage by an analog
tester.
Yes
Replace the expansion valve.
NOTE : After check of LEV, do the undermentioned operations.
1. Turn OFF the power supply and turn ON it again.
2. Press RESET button on the remote controller.
OBH648A
36
No
Replace the inverter P.C.
board.
L Check of inverter P.C. board
MUZ-HJ50VA
Check the outdoor fan motor.
(Refer to 11-5. .)
Is the fuse (F901) blown on the inverter P.C. board?
No
Yes
Check the connection of the connectors
(CN931, CN932) of the outdoor fan motor.
If the connection is poor, make it correct.
Operate the outdoor unit by starting
EMERGENCY OPERATION.
Check the LED indication on the inverter P.C. board.
Does the LED flash 10 times?
No
Check the corresponding parts
following LED indication.
(Refer to 11-3.)
Yes
(10-time flash)
Replace the inverter P.C. board.
OBH648A
37
M How to check miswiring and serial signal error
Turn OFF the power supply.
Is there rated voltage in the
power supply?
Check the power supply.
No
Yes
1. Turn ON the power supply.
2. Press the emergency operation switch.
Has the relay 52C been turned on 3 minuets later ?
[The relay will be turned on in 3 to 7 seconds by short
circuiting the timer short mode point (Refer to 10-7.).]
No
Initializing the determination of the power
receiving system
The microprocessor may have mistaken the
unit as a model receiving power from the
outdoor unit. Follow the procedure below to
start the determination of the power receiving system all over again.
1. Hold down the emergency operation
switch for 30 seconds. (Do not release the
switch even though a buzzer beeps once
in about 5 seconds. Keep holding down
the switch until a buzzer beeps again for
1 second after 30 seconds. Figure 1)
2. Turn off the power supply.
3. Wait for about 30 seconds.
4. Turn on the power supply.
5. Press the emergency operation switch.
6. The relay 52C will be turned on in 3 minutes.
Yes
No
Has the miswiring or the serial error
been indicated?
Yes
Indication of miswiring
Indication of serial signal error
OPERATION
INDICATOR lamp
Continuous blinks
Is there any miswiring, poor
contact, or wire disconnection of the indoor/outdoor
connecting wire?
Yes
Correct them.
No
A
Figure 1
Buzzer
ON
0.5-second
1-second
Beeps Beeps
Beeps
OFF
Emergency
operation switch
ON
OFF
5-second
30-second
ON
OFF
A
• Turn OFF inverter-controlled lighting
equipment.
• Turn OFF the power supply and then
turn ON again.
• Press the emergency operation switch.
After the relay
52C is turned on
3 minutes later, is
miswiring or the
serial signal error
indicated?
Yes
B
No
• Reinstall either the unit
or the light
away from
each other.
• Attach a filter
on remote
control
receiving
section of
the indoor
unit.
Turn OFF the power supply. Make sure again that the
indoor/outdoor connecting wire is correctly connected. With
the indoor/outdoor connecting wire connected, short circuit
between S2 and S3 on the outdoor terminal block. 1
<Preparation of the remote controller>
While pressing both OPERATION SELECT button and
B TOO COOL button on the remote controller at the same
time, press RESET button.
First, release RESET button.
Hold down the other two buttons for another 3 seconds.
Make sure that the indicators on the LCD screen shown in
the right figure are all displayed. Then release the buttons.
(Setting up the failure mode recall function)
Aim the remote controller at the indoor unit, and press
OPERATE/STOP (ON/OFF) button. The relay 52C will
be turned on, and the outdoor unit will be energized.
Is the rated supply voltage applied
between the S1 and S2 on the
outdoor terminal block? (Check of
supply voltage)
Yes
Is there approximately 250 VDC – 370
VDC between DB61 (+) and DB61
(–) on the inverter P.C. board in the
outdoor unit? (Voltage check of the
inverter P.C. board in the outdoor unit)
Yes
Does the LED on the inverter P.C.
board in the outdoor unit repeat
"3.6-second-OFF and 0.8-secondON quick blinking" for 3 minutes
after the outdoor unit is energized?
(Check the blinking pattern within 3
minutes after LED is turned on. After 3 minutes, LED will blink 6 times
whether the inverter P.C. board in
the outdoor unit is normal or not.)
Yes
No
1 Make sure that the wiring is correct. If the procedure is performed without correcting miswiring, it may lead to damage to the P.C. board.
Is there any problem in the
indoor/outdoor connecting wire,
such as the damage of the wire,
intermediate connection, poor
contact with the terminal block?
No
No
Replace the
inverter P.C.
board in the
outdoor unit. 2
2 Be careful of 140
VDC – 280 VDC
residual charge in
the capacitor on the
main inverter circuit.
No
Replace the
inverter P.C.
board in the
outdoor unit. 2
Replace the indoor electronic control
P.C. board. 3
3 Be sure to release the failure-mode recall function after checking.
OBH648A
38
Yes
Replace
the indoor/
outdoor connecting wire.
N Electromagnetic noise enters into TV sets or radios
Is the unit earthed?
Yes
Is the distance between the antennas
and the indoor unit within 3 m, or is the
distance between the antennas and the
outdoor unit within 3 m?
No
Earth the unit.
No
Yes
Extend the distance between the antennas and
the indoor unit, and/or the antennas and the
outdoor unit.
Is the distance between the TV sets or
radios and the indoor unit within 1 m, or
is the distance between the TV sets or
radios and the outdoor unit within 3 m?
No
Yes
Extend the distance between the TV sets and/or
radios and the indoor unit, or the TV sets or
radios and the outdoor unit.
Are the antennas damaged?
Is the coaxial cable damaged?
Is there any poor contact in the antenna wiring?
No
Yes
Replace or repair the antenna.
Replace or repair the coaxial cable.
Yes
Extend the distance between the indoor/outdoor
connecting wire of the air conditioner and the wiring of the antennas.
Is the indoor/outdoor connecting wire
of the air conditioner and the wiring of
the antennas close?
No
Even if all of the above conditions are fulfilled, the electromagnetic noise may enter, depending on the electric field strength
or the installation condition (combination of specific conditions such as antennas or wiring).
Check the following before asking for service.
1. Devices affected by the electromagnetic noise
TV sets, radios (FM/AM broadcast, shortwave)
2. Channel, frequency, broadcast station affected by the electromagnetic noise
3. Channel, frequency, broadcast station unaffected by the electromagnetic noise
4. Layout of ;
indoor/outdoor unit of the air conditioner, indoor/outdoor wiring, earth wire, antennas, wiring from antennas, receiver
5. Electric field intensity of the broadcast station affected by the electromagnetic noise
6. Presence or absence of amplifier such as booster
7. Operation condition of air conditioner when the electromagnetic noise enters in
1) Turn OFF the power supply once, and then turn ON the power supply. In this situation, check for the electromagnetic
noise.
2) Within 3 minutes after turning ON the power supply, press OPERATE/STOP (ON/OFF) button on the remote controller
for power ON, and check for the electromagnetic noise.
3) After a short time (3 minutes later after turning ON), the outdoor unit starts running. During operation, check for the
electromagnetic noise.
4) Press OPERATE/STOP (ON/OFF) button on the remote controller for power OFF, when the outdoor unit stops but the
indoor/outdoor communication still runs on. In this situation, check for the electromagnetic noise.
OBH648A
39
11-6. TEST POINT DIAGRAM AND VOLTAGE
1. Inverter P.C. board
MUZ-HJ25VA MUZ-HJ35VA
Back side of unit
DB61
250 V - 370 VDC
230 VAC
Smoothing
capacitor (C61)
Fuse (F801)
T3.15AL250V
Output to drive outdoor
fan motor (CN771)
Fuse (F701)
T3.15AL250V
(-)
(+)
R.V. coil
(CN721)
Output to
drive
compressor
(LDW,
LDV,
LDU)
Front side of unit
100
Discharge temperature
thermistor/RT62
(CN641)
Fin temperature
thermistor/RT64
(CN642)
LED
Defrost thermistor/RT61
(CN641)
230 VAC
Jumper wire for pre-heat
control setting (JK)
Defrost thermistor (RT61)
200
80
160
Discharge temperature thermistor (RT62)
60
600
50
40
30
20
10
-10
0
10 20 30
Temperature (°C)
OBH648A
40
140
Resistance (kΩ)
70
700
Resistance (kΩ)
Resistance (kΩ)
Fin temperature thermistor (RT64)
180
90
0
-20
Jumper wire for changing
defrost setting (JS)
LEV connector
(CN724)
500
400
300
120
100
80
60
200
40
100
20
0
0
10
20
30
40
50
60
70
80
90 100 110 120
Temperature (°C)
40
0
0
10 20 30 40 50 60 70 80
Temperature (°C)
MUZ-HJ50VA
Back side of unit
DB61
250 - 370 VDC
(-)
(+)
Smoothing
capacitor
(C62)
Smoothing
capacitor
(C63)
Smoothing
capacitor
(C61)
R.V.coil
(CN721)
230 VAC
Fuse (F701)
T3.15AL250V
Fuse (F801)
T3.15AL250V
230 VAC
Fuse (F901)
T3.15AL250V
Output to
drive outdoor
fan motor
(CN932)
230 VAC
Output to
drive
compressor
(LDU,
LDV,
LDW)
100
Jumper wire for
changing defrost
setting (JS)
LEV connector
(CN724)
Outdoor heat exchanger
temperature thermistor
/RT68 (CN644)
Discharge temperature
thermistor/RT62
(CN641)
Defrost thermistor
/RT61(CN641)
Signal of outdoor
fan motor (CN931)
Front side of unit
Fin temperature
thermistor/RT64
(CN642)
LED
Defrost thermistor(RT61)
Outdoor heat exchanger temperature thermistor(RT68)
200
80
160
Discharge temperature thermistor(RT62)
700
60
600
50
40
30
20
10
-10
0
10 20 30
Temperature( )
OBH648A
40
140
Resistance(k )
70
Resistance(k )
Resistance(k )
Fin temperature thermistor(RT64)
180
90
0
-20
Jumper wire
for pre-heat
control setting
(JK)
500
400
300
120
100
80
60
200
40
100
20
0
0
10
20
30
40
50
60
70
80
Temperature( )
41
90 100 110 120
0
0
10 20 30 40 50 60 70 80
Temperature( )
12
DISASSEMBLY INSTRUCTIONS
<"Terminal with locking mechanism" Detaching points>
The terminal which has the locking mechanism can be detached as shown below.
There are two types (refer to (1) and (2)) of the terminal with locking mechanism.
The terminal without locking mechanism can be detached by pulling it out.
Check the shape of the terminal before detaching.
(1) Slide the sleeve and check if there is a locking lever or not.
Sleeve
Locking lever
(2) The terminal with this connector has the
locking mechanism.
Slide the sleeve.
Pull the terminal while
pushing the locking
lever.
12-1. MUZ-HJ25VA MUZ-HJ35VA
Hold the sleeve, and
pull out the terminal
slowly.
Connector
NOTE: Turn OFF power supply before disassembly.
OPERATING PROCEDURE
PHOTOS
1. Removing the cabinet and the panels
Photo 1
(1) Remove the screw fixing the service panel.
(2) Pull down the service panel and remove it.
(3) Disconnect the power supply and indoor/outdoor connecting wire.
(4) Remove the screws fixing the top panel.
(5) Remove the top panel.
(6) Remove the screws fixing the cabinet.
(7) Remove the cabinet.
(8) Remove the fixing screws of the terminal block support
and the back panel. (Photo 4)
(9) Remove the screws fixing the back panel.
(10) Remove the back panel.
Photo 2
Screws of
the top panel
Screws of
the top panel
Screws of the cabinet
Photo 3
Screws of
the back panel
Direction to
remove
Screws of
the service panel
Hooks
Screw of the cabinet
OBH648A
42
OPERATING PROCEDURE
PHOTOS
Photo 4
2. Removing the inverter assembly, inverter P.C.
board
Screw of the
heat sink and the
separator
(1) Remove the cabinet and the panels. (Refer to 1.)
(2) Disconnect the lead wire to the reactor and the following connectors:
<Inverter P.C. board>
CN721 (R.V. coil)
CN771 (Fan motor)
CN641 (Defrost thermistor and discharge temperature
thermistor)
CN724 (LEV)
(3) Remove the compressor connector (CN61).
(4) Remove the screws fixing the heat sink support and
the separator.
(5) Remove the inverter assembly.
(6) Remove the screw of the earth wire and the screw of
the terminal block support.
(7) Remove the screw of the terminal block and remove
the terminal block.
(8) Remove the heat sink support from the P.C. board
support.
(9) Unhook the catch of the inverter P.C. board and
remove the inverter P.C. board from the P.C. board
support.
Screws of the terminal
block support and the
back panel
Photo 5 (Inverter assembly)
3. Removing the R.V. coil
(1) Remove the cabinet and the panels. (Refer to 1.)
(2) Disconnect the following connectors:
<Inverter P.C. board>
CN721 (R.V. coil)
(3) Remove the R.V. coil.
Heat sink
Heat sink
support
P.C. board
support
Screw of the
earth wire
Terminal block
support
Inverter
P.C. board
OBH648A
43
Screw of the
terminal block support
OPERATING PROCEDURE
PHOTOS
Photo 6
4. Removing the discharge temperature thermistor
and the defrost thermistor
Suction pipe brazed part
(1) Remove the cabinet and the panels. (Refer to 1.)
(2) Disconnect the lead wire to the reactor and the following connectors:
<Inverter P.C. board>
CN641 (Defrost thermistor and discharge temperature
thermistor)
(3) Pull out the discharge temperature thermistor from its
holder.
(4) Pull out the defrost thermistor from its holder.
R.V. coil
Screws of
the reactor
Photo 7
Discharge pipe
brazed part
Discharge temperature thermistor
Suction pipe
brazed part
4-way valve
brazed part
5. Removing the outdoor fan motor
(1) Remove the cabinet and the panels. (Refer to 1.)
(2) Disconnect the following connectors:
<Inverter P.C. board>
CN771 (Fan motor)
(3) Remove the fan motor lead wire from where it is fastened on the separator.
(4) Remove the propeller nut.
(5) Remove the propeller.
(6) Remove the screws fixing the fan motor.
(7) Remove the fan motor.
Discharge
pipe
brazed
part
4-way valve
brazed part
Photo 8
Defrost
thermistor
6. Removing the compressor and the 4-way valve
(1) Remove the cabinet and the panels. (Refer to 1.)
(2) Remove the inverter assembly. (Refer to 2.)
(3) Remove the screws of the reactor and remove the
reactor.
(4) Remove the screws of the separator and remove the
separator.
(5) Remove the soundproof felt.
(6) Remove the terminal cover and the compressor lead
wire.
(7) Recover gas from the refrigerant circuit.
NOTE: Recover gas from the pipes until the pressure
gauge shows 0 kg/cm2 (0 MPa).
(8) Detach the brazed part of the suction and the discharge pipe connected with the compressor.
(9) Detach the brazed part of pipes connected with the
4-way valve.
(10) Remove the nuts of compressor legs.
(11) Remove the compressor.
OBH648A
Propeller
44
Screws of the outdoor fan motor
12-2. MUZ-HJ50VA
NOTE: Turn OFF power supply before disassembly.
OPERATING PROCEDURE
PHOTOS
1. Removing the cabinet and the panels
Photo 1
(1) Remove the screw fixing the service panel.
(2) Pull down the service panel and remove it.
(3) Disconnect the power supply and indoor/outdoor connecting wire.
(4) Remove the screws fixing the top panel.
(5) Remove the top panel.
(6) Remove the screws fixing the cabinet.
(7) Remove the cabinet.
(8) Remove the fixing screws of the terminal block support
and the back panel.
(9) Remove the screws fixing the back panel.
(10) Remove the back panel.
Screws of the
top panel
Screws of
the top panel
Back
panel
Screw
of the
back
panel
Screws of
the cabinet
Photo 2
Screw of the
cabinet
Service
panel
Screws of
the terminal block
support and the
back panel
Screw of the
service panel
Direction to
remove
Screws of
the cabinet
OBH648A
45
Hooks
OPERATING PROCEDURE
PHOTOS
2. Removing the inverter assembly, inverter P.C. board
(1) Remove the cabinet and the panels. (Refer to 1.)
(2) Disconnect the lead wire to the reactor and the following connectors:
<Inverter P.C. board>
CN721 (R.V. coil)
CN931, CN932 (Fan motor)
CN641 (Defrost thermistor and discharge temperature thermistor)
CN644 (Outdoor heat exchanger temperature thermistor)
CN724 (LEV)
(3) Remove the compressor connector (CN61).
(4) Remove the screws fixing the heat sink support and the separator.
(5) Remove the inverter assembly.
(6) Remove the screw of the earth wire and the screw of the terminal block support.
(7) Remove the screw of the terminal block and remove the terminal block.
(8) Remove the heat sink support from the P.C. board support.
(9) Remove the screw of the inverter P.C. board and remove the
inverter P.C. board from the P.C. board support.
Photo 3
Screws of the heat sink
Screws of the terminal block
support and the separator support and the back panel
Photo 4 (Inverter assembly)
Heat sink Heat sink support
3. Removing the R.V. coil
(1) Remove the cabinet and the panels. (Refer to 1.)
(2) Disconnect the following connectors:
<Inverter P.C. board>
CN721 (R.V. coil)
(3) Remove the R.V. coil.
P.C. board
support
4. Removing the discharge temperature thermistor,
defrost thermistor and outdoor heat exchanger temperature thermistor
Screw of the
Terminal block
support
Terminal
block
support
Screw of the
Screw of the
inverter P.C. board earth wire
Photo 5
(1) Remove the cabinet and the panels. (Refer to 1.)
(2) Disconnect the lead wire to the reactor and the following connectors:
<Inverter P.C. board>
CN641 (Defrost thermistor and discharge temperature thermistor)
CN644 (Outdoor heat exchanger temperature thermistor)
(3) Pull out the discharge temperature thermistor from its holder.
(4) Pull out the defrost thermistor from its holder. (Photo 6)
(5) Pull out the outdoor heat exchanger temperature thermistor
from its holder. (Photo 6)
Discharge temperature thermistor
OBH648A
46
OPERATING PROCEDURE
PHOTOS
5. Removing the outdoor fan motor
Photo 6
(1) Remove the cabinet and the panels. (Refer to 1.)
(2) Disconnect the following connectors:
<Inverter P.C. board>
CN931, CN932 (Fan motor)
(3) Remove the fan motor lead wire from where it is fastened on
the separator.
(4) Remove the propeller nut.
(5) Remove the propeller.
(6) Remove the screws fixing the fan motor.
(7) Remove the fan motor.
Outdoor heat
exchanger temperature thermistor
6. Removing the compressor and the 4-way valve
(1)
(2)
(3)
(4)
Remove the cabinet and the panels. (Refer to 1.)
Remove the inverter assembly. (Refer to 2.)
Remove the screws of the reactor and remove the reactor.
Remove the screws of the separator and remove the separator.
(5) Remove the soundfproof felt.
(6) Remove the terminal cover and the compressor lead wire.
(7) Recover gas from the refrigerant circuit.
NOTE: Recover gas from the pipes until the pressure gauge
shows 0 kg/cm2 (0 MPa).
(8) Detach the brazed part of the suction and the discharge pipe
connected with the compressor.
(9) Detach the brazed part of pipes connected with the 4-way
valve.
(10) Remove the nuts of compressor legs.
(11) Remove the compressor.
Defrost thermistor
Photo 7
Screws of the outdoor fan motor
Photo 8
Screws of
the reactor
Screws of
the separator
Propeller
Propeller nut
Photo 9
Discharge pipe
brazed part
Screw of the separator
Suction pipe
brazed part
OBH648A
47
4-way valve
brazed parts
HEAD OFFICE: TOKYO BLDG., 2-7-3, MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN
© Copyright 2012 MITSUBISHI ELECTRIC CORPORATION
Distributed in Mar. 2013. No. OBH648 REVISED EDITION-A
Distributed in Dec. 2012. No. OBH648
Made in Japan
New publication, effective Mar. 2013
Specifications are subject to change without notice.