Dell™ 2200MP Projector User's Guide
The information below is provided by the supplier of the referenced device without independent verification by Dell
and is subject to the restrictions and disclaimers.
Safety Instructions (Read before connecting the projector)
About Your Projector
Installation
Using Your Projector
Troubleshooting
Specifications
Regulatory Notices
Contacting Dell
Notes, Notices, and Cautions
NOTE: A NOTE indicates important information that helps you make better use of your projector.
NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to
avoid the problem.
CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.
Information in this document is subject to change without notice.
©2003 Coretronic Corporation.
©2003 Dell Inc.. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.
Trademarks used in this text: Dell and the DELL logo are trademarks of Dell Inc.; DLP and Texas Instruments are
trademarks of Texas Instruments Corporation; Microsoft and Windows are registered trademarks of Microsoft
Corporation; Macintosh is a registered trademark of Apple Computer, Inc.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the
marks and names or their products. Dell Inc. disclaims any proprietary interest in trademarks and trade names
other than its own.
Restrictions and Disclaimers
The information contained in this document, including all instructions, cautions, and regulatory approvals and
certifications, is based upon statements provided to Dell by the manufacturer and has not been independently
verified or tested by Dell. Dell disclaims all liability in connection with any deficiencies in such information.
All statements or claims regarding the properties, capabilities, speeds, or qualifications of the part referenced in
this document are made by the manufacturer and not by Dell. Dell specifically disclaims any knowledge of the
accuracy, completeness, or substantiation for any such statements.
October 2003 Rev. A00
http://www.pureglare.com.au
Back to Contents Page
Safety Instructions: Dell™ 2200MP Projector
CAUTION
Use the following safety guidelines to help protect your projector from potential damage and to ensure your
own personal safety:
The surface beneath the projector might be hot with use. Be careful in handling the unit.
The lamp becomes very hot with use. Do not attempt to replace the lamp after use until the projector
has been allowed to cool down for at least 30 minutes, and follow all instructions in "Changing the
Lamp."
Do not touch the bulb or the lamp glass at any time. The bulb may explode due to improper handling,
including the touching of the bulb or the lamp glass.
Remove lens cap before turning on projector. Failure to do so may cause the lens cap to reach high
temperatures.
To avoid damaging the projector and lamp, allow the cooling fan to run for 2 minutes before turning
off the projector.
Do not block the ventilation slots and openings on the projector.
Disconnect the power cord from the electrical outlet if the projector is not used for a long period of
time.
Do not use the projector in an extremely hot, cold, or humid environment.
Do not use the projector in areas susceptible to excessive dust and dirt.
Do not use the projector near any appliance that generates a strong magnetic field.
Do not place the projector in direct sunlight.
Do not look into the lens while the projector is on; the bright light may hurt your eyes.
To reduce the risk of fire or electric shock, do not expose the projector to rain or moisture.
To prevent electric shock, do not open or disassemble the projector further than what is needed for
lamp replacement.
To avoid damaging the projector, ensure that the zoom lens and elevator foot are fully retracted
before moving the projector or placing the projector in its carrying case.
Turn off the projector and disconnect it from the electrical outlet before cleaning it. Use a soft cloth
moistened with mild detergent to clean the display housing. Do not use abrasive cleaners, waxes, or
solvents.
Back to Contents Page
http://www.pureglare.com.au
Back to Contents Page
About Your Projector: Dell™ 2200MP Projector
Features
Equipment
Main Unit
Control Panel
Connection Ports
Remote Control
Features
Single chip 0.55" Texas Instruments DLP™ technology
High contrast, double data rate (DDR) digital micromirror device
True SVGA, 800 x 600 addressable pixels
4.7 lbs (2.14 kgs) lightweight compact design
1200 ANSI lumens brightness (Max)*
1700:1 full on / full off contrast ratio
1.2x manual zoom lens
Built in 2W speaker
Auto image re-sizing (Auto-Sync) to 800 x 600 full screen with scaling compression compatibility for
SXGA+,SXGA, XGA, SVGA, VGA, MAC
Preset and user defined video modes for optimum video and graphic settings
Self-diagnostic for video troubleshooting
State-of-the-art motion adaptive hardware deinterlacing with 3:2 and 2:2 pull down
200-watt, user-replaceable lamp
Compatibility with Macintosh® computers
Compatibility with NTSC, NTSC4.43, PAL, PAL-M, PAL-N, SECAM, and HDTV (1080i, 720P, 576i/P,
480i/P)
Multi-function remote control
D-Sub 15-pin cable for analog video connectivity
High-definition TV compatibility
User-friendly, multi-language on-screen display (OSD)
Advanced electronic keystone correction
User-friendly control panel with backlight
Carrying case included
*Based on ANSI/NAPM IT7.228-1997 tests of 100 units, October 2003, with average ANSI Lumens 1152. Bulb
brightness degrades with usage. Dell recommends replacing your bulb after 2000 hours usage.
Equipment
Your projector comes with all the items shown below. Ensure that you have all the items, and contact Dell if
anything is missing.
http://www.pureglare.com.au
Main unit
3.0m Power cord
1.8m VGA cable
(D-sub to D-sub)
2.0m S-video cable
1.8m USB cable
1.8m Composite Video cable
1.8m D-sub to YPbPr cable
1.8m RCA to Audio cable
1.8m mini pin to mini pin cable
Remote control
Dell 2200MP Projector
User's Guide
Dell 2200MP Projector Quick Start
Card
Owner's Manual
Carrying case
Warranty Guide
Batteries (2)
http://www.pureglare.com.au
Main Unit
1
Control panel
2
Zoom tab
3
Focus ring
4
Lens
5
Elevator button
6
Remote control receiver
1
Power button
2
Four directional keys
3
Keystone adjustment
4
Temperature warning light
Control Panel
http://www.pureglare.com.au
5
Lamp warning light
6
Resync
7
Menu
8
Keystone adjustment
9
Source
1
VGA in (D-sub) connector
2
VGA out (monitor loop-through)
3
IR receiver
4
USB connector
5
S-video connector
6
Composite video connector
7
Audio input connector
Connection Ports
Remote Control
http://www.pureglare.com.au
1
Light
2
Power button
3
Previous Page button (page up)
4
Four Direction buttons
5
Source button
6
Resync button
7
Keystone Correction button
8
Volume button
9
Hide button
10
4:3/16:9 (aspect ratio) button
11
Menu button
12
Next Page button (page down)
13
Video Mode button
Battery Disposal: Your projector remote control uses zinc-manganese batteries. If you
need to replace the batteries, see your Dell 2200MP Projector Quick Start Card.
Do not dispose of used batteries along with household waste. Contact your local waste
disposal agency for the address of the nearest battery deposit site.
http://www.pureglare.com.au
Back to Contents Page
http://www.pureglare.com.au
Back to Contents Page
Installation: Dell™ 2200MP Projector
Connecting the Projector
Powering On/Off the Projector
Adjusting the Projected Image
Changing the Lamp
Connecting the Projector
A. To Computer
1
Power cord
2
D-sub to D-sub cable
3
USB to USB cable
B. To DVD Player: There are three possible methods of connecting to a DVD player.
1. Connecting with component cable:
http://www.pureglare.com.au
1
Power cord
2
D-sub to HDTV/Component cable
2. Connecting with S-video cable:
1
Power cord
2
S-video cable
3. Connecting with composite cable:
http://www.pureglare.com.au
1
Power cord
2
Composite video cable
Powering On/Off the Projector
Powering On the Projector
NOTE: Turn on the projector before you turn on the source.
1. Remove the lens cap.
2. Ensure that the power cord and appropriate signal cable(s) are securely connected. The power button light will
blink green.
3. Press the power button to turn on the projector. The Dell logo will be displayed for 30 seconds.
4. Turn on your source (computer, notebook, DVD, etc.). The projector automatically detects your source.
If the "Searching for signal..." message appears on the screen, ensure that the appropriate signal
cable(s) are securely connected.
If you are connecting multiple sources to the projector simultaneously, press the Source button on the remote
control or control panel to select the desired source.
http://www.pureglare.com.au
1
Power button
2
Lens cap
Powering Off the Projector
DO NOT UNPLUG THE PROJECTOR BEFORE PROPERLY SHUTTING DOWN USING THE FOLLOWING STEPS.
1. Press the power button to turn off the projector. The "Power Off the Lamp?" message appears on the
OSD.
2. Press the power button again. The cooling fans continue to operate for 2 minutes.
3. If the LAMP light is solid orange, replace the lamp.
4. If the TEMP light is solid orange, the projector has overheated. The display automatically shuts down. Try
turning the display on again after the projector cools down. If the problem persists, contact Dell.
5. If the TEMP light is blinking orange, a projector fan has failed and the projector will automatically shut down. If
this problem persists, contact Dell.
6. Disconnect the power cord from the electrical outlet and the projector.
7. If you press the power button while the projector is running, the "Power Off the Lamp?" message appears
on the screen. To clear the message, press any button on the control panel or ignore the message; the
message will disappear after 5 seconds.
Adjusting the Projected Image
Adjusting the Projector Height
To raise the projector:
1. Press the elevator button.
2. Raise the projector to the desired display angle, and then release the button to lock the elevator foot into
position.
3. Use the tilt adjustment wheel to fine-tune the display angle.
To lower the projector:
1. Press the elevator button.
2. Lower the projector, and then release the button to lock the elevator foot into position.
http://www.pureglare.com.au
Notice: To avoid damaging the projector, make sure that the zoom lens and elevator foot are fully retracted before
placing the projector in its carrying case.
1
Elevator button
2
Elevator foot
3
Tilt adjustment wheel
Adjusting the Projector Zoom and Focus
1. Rotate the zoom tab to zoom in and out.
2. Rotate the focus ring until the image is clear. The projector focuses at distances from 3.9 ft to 39.4ft (1.2 m to 12
m).
1
Zoom tab
2
Focus ring
Adjusting Projection Image Size
http://www.pureglare.com.au
Max.
Screen
(Diagonal) Min.
Screen
Size
Max.
(WxH)
Min.
(WxH)
33.7" (85.7cm)
27.9" (70.8cm)
27.0"X20.2"
95.6" (242.9cm)
78.9" (200.5cm)
76.5"X57.4"
154.7" (392.9cm)
127.7" (324.3cm)
123.7"X92.8"
216.5" (550.0cm)
178.7" (454.0cm)
173.2"X129.9"
275.6" (700.0cm)
227.5" (577.8cm)
220.5"X165.4"
337.5" (857.1cm)
278.6" (707.5cm)
270.0"X202.5"
(68.6cmX51.4cm) (194.3cmX145.7cm) (314.3cmX235.7cm) (440.0cmX330.0cm) (560.0cmX420.0cm) (685.7cmX514.3cm)
22.3"X16.7"
63.1"X47.4"
102.1"X76.6"
143.0"X107.2"
182.0"X136.5"
222.8"X167.1"
(56.6cmX42.5cm) (160.4cmX120.3cm) (259.4cmX194.6cm) (363.2cmX272.4cm) (462.3cmX346.7cm) (566.0cmX424.5cm)
Distance
3.9'(1.2m)
11.2'(3.4m)
18.0'(5.5m)
25.3'(7.7m)
32.2'(9.8m)
39.4'(12.0m)
* This graph is for user reference only.
Changing the Lamp
Replace the lamp when you see " Lamp is approaching the end of its useful life in
full power operation. Replacement suggested!" message on the screen by carefully
following these instructions. If this problem persists, contact Dell.
CAUTION: The lamp becomes very hot with use. Do not attempt to replace the lamp after use until the projector
has been allowed to cool down for at least 30 minutes.
Lamp Changing Procedure:
1. Turn off the projector and disconnect the power cord.
2. Let the projector cool for at least 30 minutes.
3. Loosen the 2 screws that secure the lamp cover, and
remove the cover.
4. Loosen the 3 screws that secure the lamp.
5. Pull up the lamp by its metal handle.
http://www.pureglare.com.au
6. Reverse steps 1 through 5 to install the new lamp.
7. Reset the lamp by selecting the left Lamp Reset icon in
the OSD Management tab.
8. Dell may require that lamps replaced under warranty are
returned to Dell. Otherwise, contact your local waste
disposal agency for the address of the nearest deposit
site.
9. The lamp contains mercury. Disposal of this material may
be regulated due to environmental considerations. For
disposal or recycling information, please contact your
local authorities or the Electronic Industries Alliance:
www.eiae.org.
CAUTION: Do not touch the bulb or the lamp glass at any time. The bulb may explode due to improper handling,
including the touching of the bulb or the lamp glass.
Back to Contents Page
http://www.pureglare.com.au
Back to Contents Page
Using Your Projector: Dell™ 2200MP Projector
Control Panel
Remote Control
On-Screen Display
Control Panel
Power
See "Powering On/Off the Projector."
Source
Press
to step through Analog RGB, Composite, Component-I, S-video, and Analog YPbPr sources when
multiple sources are connected to the projector.
Resync
Press
to synchronize the projector to the input source.
Resync will not operate if the OSD (On-Screen Display) is displayed.
Menu
Press
to activate the OSD. Use the directional keys and Menu button to navigate through the OSD.
Four Directional Keys
The four directional keys
can be used to toggle through the tabs in the OSD.
Keystone
Press
or
button to adjust image distortion caused by tilting the projector. (± 16 degrees)
Remote Control
http://www.pureglare.com.au
Power
See "Power On/Off the Projector."
Source
Press the Source button to choose Analog RGB, Composite, Component-I, S-video, and Analog YPbPr sources.
Resync
Press
to synchronize the projector to the input source.
Resync will not operate if the OSD (On-Screen Display) is displayed.
Directional Keys
Use
or
to select OSD items, use "left" and "right" button to make adjustments.
Hide
Press Hide button to hide the image, press again to resume display of the image.
Video Mode
The Dell 2200MP Microprojector has preset configurations that are optimized for displaying data (PC Graphics) or
video (movies, games, etc.). Press Video Mode button to toggle between PC mode, Movie mode, sRGB, or
User mode (for user to setup and save preferred settings). Pressing the Video Mode button once will show the
current display mode. Pressing the Video Mode button again will switch between modes.
Previous Page
Press the Previous Page button to page up.
Next Page
Press the Next Page button to page down.
Menu
Press the Menu button to activate the OSD. Use the directional keys and Menu button to navigate through the
OSD.
Volume up/down
Press the up button to increase the volume, press the down button to reduce the volume.
4:3/16:9
Press the 4:3/16:9 to switch the image aspect ratio from 4:3 to 16:9.
http://www.pureglare.com.au
Keystone
Adjusts image distortion caused by tilting the projector. ( &plusmn16 degrees)
On-Screen Display
The projector has a multi-language On-Screen Display (OSD) that can only be displayed when an input
source is present.
The OSD allows you to make image adjustments and change a variety of settings. If the source is a
computer, the OSD allows changes to the Computer Image tab. When using a video source, the OSD
allows changes to the Video Image tab. The projector automatically detects the source.
When the OSD is on the screen, press
or
to navigate through the OSD tabs.
Example: All Images--> Computer Image--> Audio--> Management--> Language--> Factory Reset. To
make a selection in a tab, press
on keypad or "Menu" on remote controller.
Press
or
to make a selection and adjust the settings by pressing
or
on keypad or Left and
Right button on the remote controller. When an item is selected, the color of the item will change to dark
gray.
To exit the OSD, go to "Exit" tab and press
button on keypad or "Menu" on remote controller.
All Images Menu
http://www.pureglare.com.au
Brightness
Adjusts the brightness of the image.
Press
to darken the image.
Press
to lighten the image.
Contrast
Controls the degree of difference between the lightest and darkest parts of the picture.
Adjusting the contrast changes the amount of black and white in the image.
Press
to decrease the contrast.
Press
to increase the contrast.
Color Temp.
Adjusts the color temperature. With the higher temperature, the screen looks colder;
with the lower temperature, the screen looks warmer. User mode activates the values
in the "color setting" menu.
Color Setting
http://www.pureglare.com.au
This mode allows for manual adjustment of red, green, and blue color settings.
Modifying these values will automatically change the color temperature to "user".
Keystone
Adjusts image distortion caused by tilting the projector. (&plusmn16 degrees)
Aspect Ratio
Select this function to fit 16:9U, 1:1, 16:9, 4:3 aspect ratio. In order to use the 1:1
aspect ratio, the input must be a computer signal (through VGA cable) of resolution less
than SVGA (800 x 600), component 576p/ 480i / 480p, S-Video, or Video (composite).
If the input signal is a computer signal greater than SVGA or component 1080i / 720p,
only 16:9, 16:9U or 4:3 aspect ratio will be available. When an icon is selected, the
color of the icon will change to dark blue.
16:9U The input source will be displayed in wide screen mode (16:9) without scaling.
Some pixels will be truncated accordingly.
1:1 The input source will be displayed without scaling.
16:9 The input source will be displayed in wide screen mode (16:9) without scaling.
The source will be scaled to fit the width of the screen.
4:3 The input source will be scaled to fit the screen.
Video Mode
Select this function to optimize the display image for home use (Movie Mode),
conference use (PC Mode), standard color use (sRGB), or as user preferable settings
(User Mode). When an icon is selected, the color of the icon will change to dark blue.
The default setting is PC Mode. Adjusting the settings of White Intensity or Degamma
tab will select User Mode automatically.
White Intensity
White Intensity can be adjusted between 0 and 10.
Setting 10 will maximize the brightness.
Setting 0 will maximize color reproduction quality.
Degamma
http://www.pureglare.com.au
Degamma can be adjusted between 1 and 7. Default setting is 3 (Recommended).
Adjustment of the setting will change the color performance of the display.
Audio Menu
Audio
Volume
Press
to decrease the volume.
Press
to increase the volume.
Treble
Control the higher frequencies of your audio source.
Press
to decrease the treble.
Press
to increase the treble.
http://www.pureglare.com.au
Bass
Control the lower frequencies of your audio source.
Press
to decrease the bass.
Press
to increase the bass.
Mute
Select the left icon to mute the volume.
Select the right icon to unmute the volume.
Management Menu
http://www.pureglare.com.au
Management
Menu Location
Select the location of the OSD on the screen.
Projection Mode
Front Projection-Desktop
The default setting.
Rear Projection-Desktop
The projector reverses the image so you can project from behind a translucent
screen.
Front Projection-Ceiling Mount
The projector turns the image upside down for ceiling-mounted projection.
Rear Projection-Ceiling Mount
The projector simultaneously reverses and turns the image upside down. You
can project from behind a translucent screen with a ceiling-mounted projection.
Signal Type
Manually select signal type RGB, YCbCr, YPbPr.
Lamp Hour
Displays operating hours since lamp timer reset.
Lamp Reset
Use this function only after a new lamp is installed in the projector. Select the left
Lamp Reset icon (light bulb and arrow under the icon), and press the Enter button to
reset the lamp timer.
Power Saving Menu
http://www.pureglare.com.au
Power Saving
Use this function to select the power saving delay period. Press "Yes" to go into the "set
time" sub menu.
Set Time(Min)
Set the power saving delay period as you prefer. When the projector is not receiving an
input signal for the selected period of time, the projector will automatically enter power
saving mode, and turn off the lamp. After a one-minute cooling period, the projector will
turn back on with detection of an input signal or by pressing the "Power" button. After
two hours the projector will turn off and must be turned on by pressing the power
button on the control panel or remote.
Auto Source
The projector will always automatically search for available input signals when Auto
Source is On, which is the default setting. Press the "Source" button with Auto Source
On to automatically search for the next available input signal. Selecting Off will lock on
the current input source. Set Auto-Source to Off to step through the different input
signals manually.
ECO Mode
Use this function to dim the projector lamp light output which will lower power
consumption and increase lamp life. Selecting "On" will dim the projector lamp; selecting
"Off" will return the lamp to high brightness mode.
High Altitude
http://www.pureglare.com.au
Turning on High Altitude mode operates the fans at full speed continuously to allow for
proper high altitude cooling of the projector.
Language Menu
Language
Language
Press
or
to select the language you prefer.
Factory Reset Menu
http://www.pureglare.com.au
Factory Reset
Select Yes to reset the projector to its factory default settings. Reset items include both
computer image and video image settings.
Computer Image Menu
Computer Image- Note: this menu is only available with computer input signal.
Frequency
Change the display data frequency to match the frequency of your computer graphic
card. If you experience a vertical flickering bar, use the frequency function to make an
http://www.pureglare.com.au
adjustment.
Tracking
Synchronize the signal timing of the display with that of the graphic card. If you
experience an unstable or flickering image, use the tracking function to correct it.
Hor. Position (Horizontal Position)
Press
to move the image left.
Press
to move the image right.
Ver. Position (Vertical Position)
Press
to move the image down.
Press
to move the image up.
Video Image Menu
Video Image- Note: this menu is only available with S-video, video(composite) signal.
Saturation
Adjust a video image from black and white to fully saturated color.
Press
to decrease the amount of color in the image.
http://www.pureglare.com.au
Press
to increase the amount of color in the image.
Sharpness
Adjust the sharpness of the image.
Press
to decrease the sharpness.
Press
to increase the sharpness.
Tint
Adjust the color balance of red and green.
Press
to increase the amount of green in the image.
Press
to increase the amount of red in the image.
Back to Contents Page
http://www.pureglare.com.au
Back to Contents Page
Troubleshooting: Dell™ 2200MP Projector
No image appears on the screen
Partial, scrolling, or incorrectly displayed image
The screen does not display your presentation
Image is unstable or flickering
Image has vertical flickering bar
Image color is not correct
Image is out of focus
The image is stretched when displaying 16:9 DVD
Image is reversed
Lamp is burned out or makes a popping sound
Self-diagnostic for video
Noise made when turning projector upside down
If you experience problems with your projector, see the following troubleshooting tips. If the problem persists,
contact Dell.
No image appears on the screen
Ensure that the lens cap is removed and the projector is turned on.
Ensure the external graphics port is enabled. If you are using a Dell portable computer,
press
. For other computers, consult your owner's manual.
Ensure that all the cables are securely connected as described in "Connecting the
Projector."
Ensure that the pins of the connectors are not bent or broken.
Ensure that the lamp is securely installed (see "Changing the Lamp").
Run "Self-diagnostic test" (see " Self-diagnostic for video" ) for preliminary diagnostic on
projection problem for video. Ensure that the colors of the test pattern are correct.
Partial, scrolling, or incorrectly displayed image
Press the Resync button on the remote control or the control panel.
If you are using a Dell portable computer (for other computers consult your owner's
manual):
1. Set the resolution of the computer to SVGA (800 x 600):
1a) Right click on the unused portion of your Windows desktop-» Properties-»
Settings tab.
1b) Verify the "Screen area" slide bar is set to 800 x 600 pixels.
2. Press
.
http://www.pureglare.com.au
If you experience difficulty in changing resolutions or your monitor freezes, restart all the
equipment and the projector.
The screen does not display your presentation
If you are using a portable computer, press
.
Image is unstable or flickering
Adjust the tracking in the OSD Computer Image tab.
Image has vertical flickering bar
Adjust the frequency in the OSD Computer Image tab.
Image color is not correct
If your graphic card output signal is "sync on Green", and you would like to display VGA
at 60Hz signal, please go into "OSD--> Management --> Signal Type" and select
"RGB".
Run "Self-diagnostic test" (see " Self-diagnostic for video " ) for preliminary diagnostic
on image color problem. Ensure that the colors of the test pattern are correct.
Image is out of focus
Adjust the focus ring on the projector lens.
Ensure that the projection screen is within the required distance from the projector (3.9ft
[1.2m] to 39.4ft [12m]).
The image is stretched when displaying 16:9 DVD
The projector automatically detects 16:9 DVD and adjusts the aspect ratio to full screen with a 4:3 (letter-box)
default setting.
If the image is still stretched, adjust the aspect ratio as follows:
If you are playing a 16:9 DVD, select 4:3 aspect ratio type on your DVD player if
capable.
If you cannot select 4:3 aspect ratio type on your DVD player, select 4:3 aspect ratio in
the "All Images" menu within the OSD function.
Image is reversed
Select Management from the OSD and adjust the projection mode.
Lamp is burned out or makes a popping sound
When the lamp reaches its end of life, it may burn out and may make a loud popping
sound. If this occurs, the projector will not turn back on until the lamp is replaced. To
replace the lamp, see "Changing the Lamp".
Self-diagnostic for video
Dell 2200MP projector provides self-diagnostic test of the projector video display (for
http://www.pureglare.com.au
Video, S-video, Component-I). Use this advanced feature for preliminary self-diagnostic
on your projector when encountering the display problem for video.
After turning on the projector, press "+" and "-" buttons on the control panel
simultaneously and release the buttons when screen goes blank.
Contact Dell if the projector doesn't enter diagnostic mode or if the colors are incorrectly
displayed.
Press "+" and "-" buttons again to exit the diagnostic mode.
While in Self-diagnostic mode, the screen will run a seven-color-cycle test as following:
"Red--> Green--> Blue--> White--> Watchet Blue--> Dark Green--> Yellow." Ensure that
the colors of the test pattern are correct.
Noise made when turning projector upside down
This is normal. This feature inside the projector allows for proper cooling in ceiling mount
applications.
Back to Contents Page
http://www.pureglare.com.au
Back to Contents Page
Specifications: Dell™ 2200MP Projector
Light Valve
single-chip DLP™ technology
Contrast Ratio
1700:1 Typical (Full On/Full Off)
Lamp
200-watt, user-replaceable lamp
Number of Pixels
800 x 600
Displayable Color
16.7M colors
Color Wheel Speed
120Hz(2X)
Projection Lens
F/2.4~2.7, f=19.7~23.6mm with 1.2x manual zoom lens
Projection Screen Size
27.9-337.5 inches (diagonal)
Projection Distance
3.9~39.4 ft (1.2m–12m)
Video Compatibility
NTSC, NTSC 4.43, PAL, PAL-M, PAL-N, SECAM, and HDTV
(1080i, 720P, 576i/P, 480i/P) compatibility
Composite video and S-video capability
H. Frequency
15kHz–70kHz horizontal scan
V. Frequency
43Hz–85Hz vertical refresh
Power Supply
universal 100–240V AC 50–60 Hz
Power Consumption
250 watts full power operation
I/O Connectors
power: AC power input socket
computer input: D-sub 15-pin for analog/ component, HDTV
input signal
computer output: one 15-pin D-sub
video input: one composite video RCA and one S-video
USB input: one USB connector
audio input: one phone jack
Weight
4.7 lbs (2.14 kgs)
Dimensions (W x H x D)
External 10.47 x 8.5 x 3.35 ± 0.04 inches (266 x 216 x 85 ±
1mm)
Environmental
operating temperature: 5 o C–35 o C (41o F–95 o F)
humidity: 80% maximum
storage temperature: –20o C to 60 o C (–4 o F to 140o F)
humidity: 80% maximum
FCC, CE, VCCI, UL, cUL, TüV GS, ICES-003, MIC, C-Tick,
GOST, PCBC, CCC, PSB, EZU, TüV-S, NOM
Regulatory
Compatibility Modes
(ANALOG)
Mode
Resolution
V. Frequency
(Hz)
VGA
640X350
70
31.5
VGA
640X350
85
37.9
http://www.pureglare.com.au
H. Frequency
(KHz)
VGA
640X400
85
37.9
VGA
640X480
60
31.5
VGA
640X480
72
37.9
VGA
640X480
75
37.5
VGA
640X480
85
43.3
VGA
720X400
70
31.5
VGA
720X400
85
37.9
SVGA
800X600
56
35.2
SVGA
800X600
60
37.9
SVGA
800X600
72
48.1
SVGA
800X600
75
46.9
SVGA
800X600
85
53.7
*XGA
1024X768
43.4
35.5
*XGA
1024X768
60
48.4
*XGA
1024X768
70
56.5
*XGA
1024X768
75
60.0
*XGA
1024X768
85
68.7
*SXGA
1280X1024
60
63.98
*SXGA+
1400X1050
60
63.98
MAC II 13
640X480
66.68
35
*MAC 16
832X624
74.55
49.725
*MAC 19
1024X768
75
60.24
*MAC
1152X870
75.06
68.68
MAC G4
640X480
60
31.35
*IMAC DV
1024X768
75
60
* Compression computer image.
Back to Contents Page
http://www.pureglare.com.au
Back to Contents Page
Regulatory Notices: Dell™ 2200MP Projector
Federal Communications Commission (FCC) Notice (U.S. Only)
FCC Declaration of Conformity
CE Declaration of Conformity for a Class B Digital Device
Canadian Regulatory Information (Canada Only)
EN 55022 Compliance (Czech Republic Only)
VCCI Class 2 Notice (Japan Only)
MIC Notice (South Korea Only)
Polish Center for Testing and Certification Notice
NOM Information (Mexico Only)
Regulatory Listing
Federal Communications Commission (FCC) Notice (U.S. Only)
NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
Reorient or relocate receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
This device may not cause harmful interference.
This device must accept any interference received including interference that may cause undesired
operation.
Instructions to Users: This equipment complies with the requirements of FCC (Federal Communication
Commission) equipment provided that the following conditions are met.
1. Power cable: Shielded power cable must be used.
2. Video inputs: The input signal amplitude must not exceed the specified level.
NOTICE: Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
FCC Declaration of Conformity
According to 47 CFR, Part 15 of the FCC Rules
* For the following named product:
DLP Projector
2200MP/DELL CHC7229
* Manufactured at:
http://www.pureglare.com.au
Coretronic Corporation
We hereby declare that this device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received,
including interference that may cause undesired operation.
* FCC Rules:
Tested to comply with FCC part 15, class B
* Test site at:
Advance Data Technology Corporation
No.81-1, Lu Liao Keng, 9 Ling, Wu Lung Tsung, Chiung Lin Hsiang, Hsin
Chu Hsien, Taiwan
* Responsible Party for
Product Compliance:
Coretronic Corporation
No 11, Li Hsing Rd, Science-Based Industrial Park, Hsinchu, Taiwan
Tel: 886-3-5772000 Fax: 886-3-5790066
* Manufacturer Information:
Coretronic Corporation
RD Center
No 11, Li Hsing Rd, ScienceBased Industrial Park, Hsinchu,
300, Taiwan
Technology Engineering
Associate Vice President
Hsinchu, October 01, 2003
Mr. Vincent Lin
October 01, 2003
CE Declaration of Conformity for a Class B Digital Device
Directives to which conformity is declared:
EMC Directives 89/336/EEC and Amending Directive 92/31/EEC
And
Low Voltage Directive 73/23/EEC
Standards to which conformity is declared
EN55022: 1998; EN55024: 1998; EN60950: 2000;
EN61000-3-2: 1995; EN61000-3-3: 1995
Manufacturer's Name: Coretronic Corporation
Manufacturer's Address: No 11, Li Hsing Rd, Science-Based Industrial Park, Hsinchu, Taiwan
Importer's Address:
Dell Products Europe BV
Raheen Industrial Estate, Limerick, Ireland
Type of Equipment: DLP Projector
Model Number(s): 2200MP
Reference Report Number:
Previously Declared Models:
I, the undersigned, hereby declare that the equipment specified above conforms to the above Directive(s) and
standards.
Hsinchu, Taiwan
October 01, 2003
Mr. Vincent Lin
Head of RD Center
http://www.pureglare.com.au
Canadian Regulatory Information (Canada Only)
This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out
in the Radio Interference Regulations of the Canadian Department of Communications.
Note that Industry Canada regulations provided, that changes or modifications not expressly approved by Dell
Inc. could void your authority to operate this equipment.
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations.
Cet appareil numerique de la classe B respecte toutes les exigences du Reglement sur le materiel brouilleur du
Canada.
EN 55022 Compliance (Czech Republic Only)
This device belongs to Class B devices as described in EN 55022, unless it is specifically stated that it is a Class
A device on the specification label. The following applies to devices in Class A of EN 55022 (radius of protection
up to 30 meters). The user of the device is obliged to take all steps necessary to remove sources of interference
to telecommunication or other devices.
VCCI Class 2 Notice (Japan Only)
This equipment complies with the limits for a Class 2 digital device (devices used in or adjacent to a residential
environment) and conforms to the standards for information technology equipment that are set by the Voluntary
Control Council for Interference for preventing radio frequency interference in residential areas.
Class B ITE
MIC Notice (South Korea Only)
B Class Device
http://www.pureglare.com.au
Please note that this device has been approved for non-business purposes and may be used in any
environment, including residential areas.
Polish Center for Testing and Certification Notice
The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All
equipment that works together (computer, monitor, printer, and so on) should have the same power supply
source.
The phasing conductor of the room's electrical installation should have a reserve short-circuit protection device in
the form of a fuse with a nominal value no larger than 16 amperes (A).
To completely switch off the equipment, the power supply cable must be removed from the power supply socket,
which should be located near the equipment and easily accessible.
A protection mark "B" confirms that the equipment is in compliance with the protection usage requirements of
standards PN-93/T-42107 and PN-89/E-06251.
http://www.pureglare.com.au
NOM Information (Mexico Only)
The following information is provided on the device(s) described in this document in compliance with the
requirements of the official Mexican standards (NOM)
Exporter:
Dell Inc.
One Dell Way
Round Rock, TX 78682
Importer:
Dell Computer de México,
Paseo de la Reforma 2620, 11th Floor
Col. Lomas Altas
México DF
CP 11950
Ship to:
Dell Computer de Mexico,
S.A. de C.V. al Cuidado de Kuehne & Nagel
de México S. de R.I., Avenida Soles No. 55
Col. Peñon de los Baños, 15520 Mexico, D.F.
Supply voltage:
> 100–240 VAC
Frequency:
50–60 Hz
Current consumption:
2.7 A
Regulatory Listing
Safety Certifications:
UL 60950
cUL
NOM
CE Mark--EN60950: 2000
EZU
IEC 60950:1999
TüV GS
PCBC
GOST
CCC
PSB
TüV-S
http://www.pureglare.com.au
EMC Certifications:
FCC Part 15 Class B
CE Mark--EN55022:1998 Class B, EN61003-3:1995, EN55024:1998, EN61000-3-2:1995, EN61000-33:1995
ICES-003
EZU
PCBC
C-Tick
VCCI Class B ITE
MIC
Back to Contents Page
http://www.pureglare.com.au
Back to Contents Page
Contacting Dell
To contact Dell electronically, you can access the following websites:
www.dell.com
support.dell.com (technical support)
premiersupport.dell.com (technical support for educational, government, healthcare, and
medium/large business customers, including Premier, Platinum, and Gold customers)
For specific web address for your country, find the appropriate country section in the table below.
NOTE: Toll-free numbers are for use within the country for which they are listed.
When you need to contact Dell, use the electronic addresses, telephone numbers, and codes provided in
the following table. If you need assistance in determining which codes to use, contact a local or an
international operator.
Country (City)
Department Name or Service Area, Website
and E-mail Address
Area
Code
International
Access Code
Country Code City
Code
Local
Numbers,and
Toll-Free Numbers
toll free:800-3350031
Anguilla
General Support
Antigua and
Barbuda
General Support
1-800-805-5924
toll free: 0800 444
0733
Argentina
(Buenos Aires)
Technical Support and Customer Care
International Access
Code:00
Sales
Country Code:54
Tech Support Fax
11
4515-7139
Customer Care Fax
11
4515-7138
City Code:11
Website: www.dell.com.ar
toll free: 0810 444
3355
Aruba
General Support
Australia
(Sydney)
E-mail (Australia): au_tech_support@dell.com
E-mail (New Zealand):
nz_tech_support@dell.com
International Access
http://www.pureglare.com.au
toll-free:800-1578
Code:0011
Country Code:61
City Code:2
Home and Small Business
1-300-65-55-33
Government and Business
toll free: 1-800-633559
Preferred Accounts Division (PAD)
toll free: 1-800-060889
Customer Care
Austria
(Vienna)
International Access
Code:900
Country Code:43
City Code:1
toll free: 1-800-819339
Corporate Sales
toll free: 1-800-808385
Transaction Sales
toll free: 1-800-808312
Fax
toll free: 1-800-818341
Switchboard
01
491 040
Home/Small Business Sales
01
795676-02
Home/Small Business Fax
01
795676-05
Home/Small Business Customer Care
01
795676-03
0660-8056
Home/Small Business Technical Support
01
795676-04
Preferred Accounts/Corporate Technical
Support
0660-8779
Website: support.euro.dell.com
E-mail: tech_support_central_europe@dell.com
Preferred Accounts/Corporate Customer Care
Bahamas
General Support
Barbados
General Support
Belgium (Brussels)
Technical Support
02
481 92 88
International Access
Code:00
Customer Care
02
481 91 19
Country Code:32
Home/Small Business Sales
toll-free:1-866-2786818
1-800-534-3142
toll free: 0800 16884
Corporate Sales
02
481 91 00
City Code:2
Fax
02
481 92 99
Switchboard
02
481 91 00
http://www.pureglare.com.au
Website: support.euro.dell.com
E-mail: tech_be@dell.com
E-mail for French Speaking Customers:
support.euro.dell.com/be/fr/emaildell/
Bermuda
General Support
1-800-890-0748
Bolivia
General Support
Brazil
International Access
Code:00
Country Code:55
Customer Support, Technical Support
toll free: 800-100238
toll free: 0800 90
3355
Technical Support Fax
51
481-5470
Customer Care Fax
51
481-5480
toll free: 0800 90
3390
City Code:51
Sales
Website: www.dell.com/br
British Virgin
Islands
General Support
Brunei
Customer Technical Support
(Penang, Malaysia)
604
633 4966
Customer Service
(Penang, Malaysia)
604
633 4949
Transaction Sales
(Penang, Malaysia)
604
633 4955
Country Code:673
Automated Order-Status System
Canada
(North York, Ontario)
International Access
Code:011
toll-free:1-866-2786820
toll free: 1-800-4339014
AutoTech (Automated technical support)
toll free: 1-800-2479362
Customer Care Home & Home Office & Small
Business
1-800-847-4096
Customer Care Medium, Large, Commercial,
Government (100+ Employees)
1-800-326-9463
Technical Support Home & Home Office &
Small Business
1-800-847-4096
Technical Support Medium, Large, Commercial,
Government (100+ Employees)
1-800-387-5757
http://www.pureglare.com.au
Sales (direct-from outside Toronto)
Sales (direct-from within Toronto)
416-758-2200
Sales (federal government, education, and
medical)
1-800-567-7542
TechFax
1-800-387-5752
Cayman Islands
General Support
Chile
(Santiago)
Sales, Customer Support, and Technical
Support
toll free: 1-800-9501329
1-800-805-7541
toll free: 1230-0204823
Country Code:56
City Code:2
China
(Xiamen)
Country Code:86
City Code:592
Tech Support website:
Tech Support E-mail: cn_support@dell.com
Tech Support Fax
support.ap.dell.com/china
818-1350
Projector Technical Support Phone
toll free: 800 858
2920
Customer Experience
toll free: 800 858
2060
Home and Small Business
toll free: 800 858
2222
Preferred Accounts Division
toll free: 800 858
2062
Large Corporate Accounts North
toll free: 800 858
2999
Large Corporate Accounts North Government
and Education
toll free: 800 858
2955
Large Corporate Accounts East
toll free: 800 858
2020
Large Corporate Accounts East Government
and Education
toll free: 800 858
2669
Large Corporate Accounts Queue Team
toll free: 800 858
2572
http://www.pureglare.com.au
Large Corporate Accounts South
toll free: 800 858
2355
Large Corporate Accounts West
toll free: 800 858
2811
Large Corporate Accounts GCP
toll free: 800 858
2055
Large Corporate Account Key Accounts
toll-free:800-8582628
Large Corporate Accounts Spare Parts
toll free: 800-858-2621
Colombia
General Support
980-9-15-3978
Costa Rica
General Support
Czech Republic
(Prague)
Technical Support
02
22 83 27 27
Customer Care
02
22 83 27 11
International Access
Code:00
Fax
02
22 83 27 14
TechFax
02
22 83 27 28
Switchboard
02
22 83 27 11
Country Code:420
City Code:2
0800-012-0435
Website: support.euro.dell.com
E-mail: czech_dell@dell.com
Denmark
(Horsholm)
Technical Support
Customer Care(Relational)
70230184
International Access
Code:00
Home/Small Business Customer Care
32875505
Switchboard (Relational)
32871200
Fax Switchboard (Relational)
32871201
Country Code:45
70230182
Switchboard (Home/Small Business)
32875000
Fax Switchboard (Home/Small Business)
32875001
Website: support.euro.dell.com
E-mail Support (portable computers):
den_nbk_support@dell.com
E-mail Support (desktop computers):
den_support@dell.com
E-mail Support (servers):
http://www.pureglare.com.au
Nordic_server_support@dell.com
Dominica
General Support
toll free: 1-866-2786821
Dominican
Republic
General Support
toll free: 1-800-1561588
Ecuador
General Support
toll-free 999-119
El Salvador
General Support
01-889-753-0777
Finland
(Helsinki)
Technical Support
09
253 313 60
Technical Support Fax
09
253 313 81
Relational Customer Care
09
253 313 38
Home/Small Business Customer Care
09
693 791 94
Fax
09
253 313 99
Switchboard
09
253 313 00
International Access
Code:990
Country Code:358
City Code:9
France
(Paris) (Montpellier)
International Access
Code:00
Country Code:33
City Code:(1)(4)
Website: support.euro.dell.com
E-mail: fin_support@dell.com
Home and Small Business
Technical Support
0825
387 270
Customer Care
0825
823 833
Switchboard
0825
004700
Switchboard (calls from outside of France)
04
Sales
0825
99 75 40 00
004 700
Fax (calls from outside of France)
Website: support.euro.dell.com E-mail: support.euro.dell.com/fr/fr/emaildell/
Corporate
04
99 75 40 001
Technical Support
0825
004 719
Customer Care
0825
338 339
Fax
01
55 94 71 01
Switchboard
01
55 94 71 00
Sales
http://www.pureglare.com.au
01
Germany
(Langen)
Technical Support
International Access
Code:00
Global Segment Customer Care
06103
766-9570
Preferred Accounts Customer Care
06103
766-9420
Large Accounts Customer Care
06103
766-9560
Public Accounts Customer Care
06103
766-9555
Switchboard
06103
766-7000
Country Code:49
06103
55 94 71 00
Home/Small Business Customer Care
Website: support.euro.dell.com
766-7200
0180-5-224 400
E-mail: tech_support_central_europe@dell.com Grenada
General Support
Guatemala
General Support
Guyana
General Support
Hong Kong
Technical Support(Dimension™ and
International Access
Code:001
Inspiron™ )
Country Code:852
Technical Support (OptiPlex™,
1-800-999-0136
toll free:1-877-4406511
296-93188
296-93191
Customer Service (non-technical, post-sales
issues)
800-93-8291
Transaction Sales
toll free: 800 96
4109
toll free: 800 96
4108
Large Corporate Accounts GCP HK
Ireland
(Cherrywood)
toll free:1-866-5403355
Latitude ™ , and Dell Precision™ )
Large Corporate Accounts HK
India
toll free: 800 90
3708
Technical Support
1600-33-8045
Sales
1600-33-8044
Ireland Technical Support
http://www.pureglare.com.au
1850
543 543
UK Technical Support (dial within UK only)
International Access
Code:16
Country Code:353
0870
908 0800
Home User Customer Care
01
204 4095
Small Business Customer Care
01
204 4444
Corporate Customer Care
01
204 4003
0870
906 0010
01
204 4444
0870
907 4000
SalesFax
01
204 0144
Fax
01
204 5960
Switchboard
01
204 4444
UK Customer Care (dial number within UK only)
Ireland Sales
UK Sales (dial within UK only)
Italy
(Milan)
International Access
Code:00
Country Code:39
City Code:2
Website: support.euro.dell.com
E-mail: dell_direct_support@dell.com
Home and Small Business
Technical Support
02
577 826 90
Customer Care
02
696 821 14
Fax
02
696 821 13
Switchboard
02
696 821 12
Website: support.euro.dell.com
E-mail: support.euro.dell.com/it/it/emaildell/
Jamaica
Corporate
Technical Support
02
577 826 90
Customer Care
02
577 825 55
Fax
02
577 035 30
Switchboard
02
577 821
Website: support.euro.dell.com E-mail: support.euro.dell.com/it/it/emaildell/
General Support (dial from within Jamaica only)
http://www.pureglare.com.au
1-800-404-9205
Japan
(Kawasaki)
International Access
Code:001
Country Code:81
Web site: support.jp.dell.com
Technical Support
44
toll free: 0120-981690
Technical Support Outside of Japan
44
556-3468
44
556-4240
Customer Care
Korea
(Seoul)
Technical Support
toll free: 080-2003800
International Access
Code:001
Sales
toll free: 080-2003600
Customer Service (Penang, Malaysia)
toll free: 604-6334949
Country Code:82
City Code:2
Latin America
Customer Service (Seoul, Korea)
080-200-3800
Fax
2194-6202
Switchboard
2194-6000
Customer Technical Support (Austin, Texas,
U.S.A.)
512
728-4093
Customer Service (Austin, Texas, U.S.A.)
512
728-3619
Fax (Technical Support and Customer Service)
(Austin, Texas, U.S.A.)
512
728-3883
Sales (Austin, Texas, U.S.A.)
512
728-4397
SalesFax (Austin, Texas, U.S.A.)
512
728-4600
or 728-3772
481 92 88
Luxembourg
Technical Support (Brussels, Belgium)
02
International Access
Code:00
Home/Small Business Sales (Brussels,
Belgium)
Country Code:352
Corporate Sales (Brussels, Belgium)
02
481 91 00
Customer Care (Brussels, Belgium)
02
481 91 19
Switchboard (Brussels, Belgium)
02
481 91 00
Fax (Brussels, Belgium)
02
481 92 99
toll free: 080016884
Website: support.euro.dell.com
E-mail: tech_be@dell.com
Macao
Technical Support
toll free: 0800 582
Country Code:853
Customer Service (Penang, Malaysia)
http://www.pureglare.com.au
604 633 4949
Transaction Sales
toll free: 0800 581
Malaysia
(Penang)
Technical Support
toll free: 1 800 888
298
International Access
Code:00
Customer Service
4
633 4949
Transaction Sales
toll free: 1 800 888
202
Corporate Sales
toll free: 1 800 888
213
Customer Technical Support
001-877-384-8979
Country Code:60
City Code: 4
Mexico
or 001-877-2693383
International Access
Code:00
Sales
50-81-8800
or 01-800-888-3355
Country Code:52
Customer Service
001-877-384-8979
or001-877-2693383
Main
50-81-8800
or 01-800-888-3355
Montserrat
General Support
toll free:1-866-2786822
Netherlands
Antilles
General Support
001-800-882-1519
Netherlands
(Amsterdam)
Technical Support
20
674 4500
Home/Small and Medium Business
20
674 5500
International Access
Code:00
Home/Small and Medium Business Fax
20
674 4775
Country Code:31
Home/Small and Medium Business Customer
Care
20
674 4200
City Code:20
Corporate
20
674 5000
Corporate Fax
20
674 4779
Corporate Customer Care
20
674 4325
Website: support.euro.dell.com
E-mail: support.euro.dell.com/nl/nl/emaildell/
http://www.pureglare.com.au
New Zealand
E-mail (New Zealand):
nz_tech_support@dell.com
E-mail (Australia): au_tech_support@dell.com
Home and Small Business
0800 446 255
Government and Business
0800 444 617
Sales
0800 441 567
Fax
0800 441 566
001-800-220-1006
Nicaragua
General Support
Norway
(Lysaker)
Technical Support
671 16882
Relational Customer Care
671 17514
International Access
Code:00
Home/Small Business Customer Care
231 62298
Switchboard
671 16800
Fax Switchboard
671 16865
Website: support.euro.dell.com
E-mail Support (portable computers):
nor_nbk_support@dell.com
E-mail Support (desktop computers):
nor_support@dell.com
E-mail Support (servers):
nordic_server_support@dell.com
Country Code:47
Panama
General Support
001-800-507-0962
Peru
General Support
0800-50-669
Poland
(Warsaw)
Customer Service Phone
22
57 95 700
Customer Care
22
57 95 999
Sales
22
57 95 750
Switchboard
22
57 95 999
Customer Service Fax
22
57 95 806
Reception Desk Fax
22
57 95 998
International Access
Code:011
Country Code:48
Website: support.euro.dell.com http://www.pureglare.com.au
E-mail: pl_support_tech@dell.com
Portugal
Technical Support
International Access
Code:00
Customer Care
Country Code:35
35
800 834 077
800 300 415
or 800 834 075
Sales
Fax
35
800 300 410
or 800 300 411
or 800 300 412
or 121 422 07 10
121 424 01 12
E-mail:
support.euro.dell.com/es/es/emaildell/
Puerto Rico
General Support
1-800-805-7545
St. Kitts and Nevis
General Support
toll free:1-877-4414731
St. Lucia
General Support
1-800-882-1521
St. Vincent and the
Grenadines
General Support
toll free:1-877-4414740
Singapore
(Singapore)
Technical Support
International Access
Code:005
Customer Service (Penang, Malaysia)
604
633 4949
Transaction Sales
toll free: 800 6011
054
Corporate Sales
toll free: 800 6011
053
Country Code:65
toll free: 800 6011
051
South Africa
(Johannesburg)
Technical Support
011
709 7710
Customer Care
011
709 7707
International Access
Code:09/091
Sales
011
709 7700
Fax
011
706 0495
Switchboard
011
709 7700
Country Code:27
City Code:11
Southeast
Asian/Pacific
Countries
Website: support.euro.dell.com
E-mail: dell_za_support@dell.com
Customer Technical Support, Customer
Service, and Sales (Penang, Malaysia)
http://www.pureglare.com.au
604
633-4810
Spain
(Madrid)
Home and Small Business
Technical Support
91
902 100 130
International Access
Code:00
Customer Care
91
902 118 540
Sales
91
902 118 541
Switchboard
91
902 118 541
Fax
91
902 118 539
Country Code:34
City Code:91
Website: support.euro.dell.com E-mail: support.euro.dell.com/es/es/emaildell/ Corporate
Technical Support
91
902 100 130
Customer Care
91
902 118 546
Switchboard
91
722 92 00
Fax
91
722 95 83
Website: support.euro.dell.com E-mail: support.euro.dell.com/es/es/emaildell/
Sweden
(Upplands Vasby)
Technical Support
08
590 05 199
Relational Customer Care
08
590 05 642
International Access
Code:00
Home/Small Business Customer Care
08
587 70 527
Country Code:46
City Code:8
Employee Purchase Program (EPP) Support
20 140 14 44
Fax Technical Support
08
590 05 594
Sales
08
590 05 185
Website: support.euro.dell.com
E-mail: swe_support@dell.com
E-mail Support for Latitude and Inspiron:
Swe-nbk_kats@dell.com
E-mail Support for OptiPlex:
Swe_kats@dell.com
E-mail Support for Servers:
nordic_server_support@dell.com
Switzerland
(Geneva)
International Access
Code:00
Technical Support (Home and Small Business)
22
0844 811 411
Technical Support (Corporate)
22
0844 822 844
Customer Care (Home and Small Business)
22
0848 802 202
http://www.pureglare.com.au
Country Code:41
Customer Care(Corporate)
City Code:22
Switchboard
22
799 01 01
Fax
22
799 01 90
Website: support.euro.dell.com
E-mail:swisstech@dell.com
0848 821 721
E-mail for French-speaking HSB and Corporate
Customers:
support.euro.dell.com/ch/fr/emaildell/
Technical Support (portable and desktop
computers)
toll free: 00801 86
1011
Technical Support (Servers)
toll free: 0080 60
1256
Transaction Sales
toll free:0800 651
228 or 0800 33 556
Corporate Sales
toll free:
0080 651 227/ 0800
33 555
Thailand
Technical Support
International Access
Code:001
toll free: 088 006
007
Customer Service (Penang, Malaysia)
Taiwan
International Access
Code:002
Country Code:886
Country Code:66
604
Sales
633 4949
toll free: 088 006
009
Trinidad and
Tobago
General Support
1-800-805-8035
Turks and Caicos
Islands
General Support
toll free:1-866-5403355
U.K.
(Bracknell)
Technical Support (Corporate/Preferred
Accounts/PAD [1000+ employees])
0870
908 0500
International Access
Code:44
Technical Support (Direct/PAD and general)
0870
908 0800
Country Code:44
Global Accounts Customer Care
01344
Corporate Customer Care
Preferred Accounts (500-5000 employees)
http://www.pureglare.com.au
373 185
or 373 186
0870
908 0500
01344
373 196
Customer Care
Central Government Customer Care
01344
373 193
Local Government & Education Customer Care
01344
373 199
Health Customer Care
01344
373 194
Home/Small Business Sales
0870
907 4000
Home/Small Business Customer Care
0870
906 0010
01344
860 456
Corporate/Public Sector Sales
Website: support.euro.dell.com
E-mail: dell_direct_support@dell.com
Uruguay
General Support
U.S.A.
(Austin, Texas)
Automated Order-Status System
toll free: 1-800-4339014
International Access
Code:011
AutoTech (portable and desktop computers)
toll free: 1-800-2479362
Projectors Technical Support
toll free: 1-877-4597298
Customer Service
toll free: 1-800-6249897
Dell Sales
toll free: 1-800-2893355
Customer Care website:
dell.co.uk/lca/customerservices
Country Code:1
toll free:000-413598-2521
or toll free: 1-800879-3355
Dell Outlet Store (Dell refurbished computers)
toll free: 1-888-7987561
Software and Peripherals Sales
toll free: 1-800-6713355
Spare Parts Sales
toll free: 1-800-3573355
Extended Service and Warranty Sales
toll free: 1-800-2474618
Fax
toll free: 1-800-7278320
http://www.pureglare.com.au
Dell Services for the Deaf, Hard-of-Hearing, or
Speech-Impaired
toll free: 1-877DELLTTY
(1-877-335-5889)
U.S. Virgin Islands
General Support
1-877-673-3355
Venezuela
General Support
8001-3605
Back to Contents Page
http://www.pureglare.com.au