U-Line | BI-95BTP | User manual | 1/4” Door & Drawer Panel Insert Installation Guide

®

INSTALL GUIDE

1/4” Door & Drawer Panel Insert

Installation Guide

The Built-In Undercounter Leader Since 1962 U-LINE.COM

1 Insert Panel Installation

Custom 1/4'' Thick Door/ Drawer Panel

Insert

Insert Panel Preparation

A custom insert panel may be inserted into the doorframe.

Custom insert panels can be flat or raised, as long as the maximum panel thickness, where inserted into the door / drawer reveal

(channel), is no more than 1/4" thick. For raised panels, the depth of the reveal is 1/4" on all four sides.

Drawer Models

1b. Drawer model inserts can be installed without removing the drawer from the unit. Simply pull the drawer open and follow instructions.

2. Pull door / drawer gasket out of groove (top edge of door / drawer only). Start in the middle and pull outward, moving toward the edge . This may take some force.

Raised panels will reduce the door’s 90° swing/zero clearance if the unit is installed next to a wall or similar type of structure.

Panel Dimensions.

The insert panel must not weigh more than 20 lbs.

Model

1115R

1175R

2115R

2175R(F)

2275DWR

29R

ADA15IM

ADA24R

BI2115

BI95

BI95BTP

CLR2160

CLRCO2175

CO1175

CO2175F

CO29(F)

22 15/16”

14 1-32”

12 15/16”

12 15/16”

14 1/32”

23 1/32”

22 15/16”

23 1/32”

19 13/16”

Width

13 15/16”

22 15/16”

14 1/32”

23 1/32”

23 1/32”

19 13/16”

13 15/16”

26 15/16”

27 11/16”

13 15/32”

13 15/32”

27 11/16”

27 11/16”

26 15/16

27 11/16”

21 13/32”

Height

26 15/16”

26 15/16”

27 11/16”

27 11/16”

12 15/32”

21 13/32”

26 15/16”

Insert Panel Installation

Door Models

1a. Remove top hinge screw pin with Phillips head screwdriver.

Remove door by tilting forward and lifting off bottom hinge pin.

3. Remove the two outside screws holding door / drawer handle.

Slightly separate door handle from door.

4. Pull handle up and off.

CAUTION

Use care when handling the insert. Insert edges may be sharp.

5. Slide custom door panel insert into 1/4-inch channel in door / drawer front.

Use care not to damage magnet, located on door bottom, when installing door insert. Do not set door on bottom edge when pushing insert into place.

6. Holding door / drawer gasket out of the way, replace handle on door, making sure it is seated properly on insert and that screw holes line up.

7. Install two small screws removed in Step 3.

8. Starting at the corners and working inward, push door gasket into place on door.

Door Models Only

9. Place door on bottom hinge pin and install upper hinge screw.

U-Line Insert Panel Installation 1

INSTALLATION GUIDE

®

SERVICE INFORMATION

If you have a problem with this appliance, your use and care guide has troubleshooting information to help you quickly identify common problems and provide information on possible cause and remedy. Answers to

Customers Frequently Asked Questions are available at www.u-line.com/customer/faq.cfm. You may contact

U-Line directly:

GENERAL INQUIRIES:

U-Line Corporation

P.O. Box 245040

Milwaukee, Wisconsin 53224-9540 U.S.A.

Phone (414) 354-0300

FAX (414) 354-7905

Email: [email protected]

www.u-line.com

SERVICE ASSISTANCE:

Phone (800) 779-2547

FAX (414) 354-5696

Email: [email protected]

www.u-lineservice.com

PARTS ASSISTANCE:

E-mail: [email protected]

ABOUT U-LINE

Building on 45 years, U-Line has captivated those with an appreciation for the finer things with exceptional design, inspired innovations and attention to even the smallest details.

U-Line is synonymous with premium built-in undercounter ice making, refrigeration and wine storage appliances, the U-Line Corporation is committed to luxury under the counter. U-Line is known and respected for unwavering dedication to product innovation, quality and selection. A bold and broad line of models is the product of visionaries in the pursuit of distinctive living environments in the kitchen and spaces beyond.

In 1962, Henry Uihlein founded U-Line Corporation as an outgrowth of Ben-Hur Freezer Company and was the first to develop and patent an automatic stand-alone undercounter residential ice maker. His foresight and determination to develop new ideas and to succeed when there were no clear guidelines or solutions are evident today. The Milwaukee, Wisconsin based family operated business provides continuity and vision from which innovations continue to be born.

Going forward, U-Line will continue offering best-in-class products that build on the company's numerous patents and world firsts to guide the undercounter industry in realizing its unlimited potential.

The Built-In Undercounter Leader Since 1962 U-LINE.COM

©2009 U-Line Corporation

Publication Number 30304 7/2010 Rev. A