Abit IS7-V User`s manual

Add to my manuals
80 Pages

advertisement

Abit IS7-V User`s manual | Manualzz
IS7-V
Socket 478 System Board
User’s Manual
4200-0388-02
Rev. 1.00
Copyright and Warranty Notice
The information in this document is subject to change without notice and does not
represent a commitment on part of the vendor, who assumes no liability or
responsibility for any errors that may appear in this manual.
No warranty or representation, either expressed or implied, is made with respect to the
quality, accuracy or fitness for any particular part of this document. In no event shall
the manufacturer be liable for direct, indirect, special, incidental or consequential
damages arising from any defect or error in this manual or product.
Product names appearing in this manual are for identification purpose only and
trademarks and product names or brand names appearing in this document are the
property of their respective owners.
This document contains materials protected under International Copyright Laws. All
rights reserved. No part of this manual may be reproduced, transmitted or transcribed
without the expressed written permission of the manufacturer and authors of this
manual.
If you do not properly set the motherboard settings, causing the motherboard to
malfunction or fail, we cannot guarantee any responsibility.
IS7-V
Table Of Contents
快速安裝指引 ............................................................................................ 2
速いインストールガイド ........................................................................ 4
Schneller Installation Führer .................................................................. 6
Guide Rapide d'Installation .................................................................... 8
Быстро Направляющий выступ Установки ................................... 10
Guida Rapida Dell'Installazione ........................................................... 12
Chapter 1.
1-1.
1-2.
Chapter 2.
2-1.
2-2.
2-3.
2-4.
Hardware Setup.................................................................... 2-1
Install The Motherboard...........................................................................2-1
Install Pentium® 4 CPU and Heatsink Supporting-Base..........................2-2
Install System Memory ............................................................................2-3
Connectors, Headers and Switches ..........................................................2-4
(1). ATX Power Input Connectors........................................................2-4
(2). FAN Connectors.............................................................................2-5
(3). CMOS Memory Clearing Header ..................................................2-6
(4). Front Panel Audio Connection Header ..........................................2-7
(5). Front Panel Switches & Indicators Headers ..................................2-8
(6). Additional USB Port Headers........................................................2-9
(7). System Management Bus Headers...............................................2-10
(8). Internal Audio Connectors ...........................................................2-10
(9). Accelerated Graphics Port Slot ....................................................2-11
(10). Floppy Disk Drive Connector ......................................................2-12
(11). IDE Connectors............................................................................2-13
(12). Serial ATA Connectors .................................................................2-14
(13). Back Panel Connectors ................................................................2-15
Chapter 3.
3-1.
3-2.
3-3.
Introduction .......................................................................... 1-1
Features & Specifications ........................................................................1-1
Layout Diagram .......................................................................................1-3
BIOS Setup............................................................................ 3-1
SoftMenu Setup........................................................................................3-2
Standard CMOS Features.........................................................................3-4
Advanced BIOS Features.........................................................................3-7
User’s Manual
3-4.
3-5.
3-6.
3-7.
3-8.
3-9.
3-10.
3-11.
3-12.
3-13.
Advanced Chipset Features....................................................................3-10
Integrated Peripherals ............................................................................3-12
Power Management Setup .....................................................................3-17
PnP/PCI Configurations.........................................................................3-19
PC Health Status ....................................................................................3-21
Load Fail-Safe Defaults .........................................................................3-22
Load Optimized Defaults .......................................................................3-22
Set Password ..........................................................................................3-22
Save & Exit Setup ..................................................................................3-22
Exit Without Saving...............................................................................3-22
Appendix A.
Install Intel Chipset Software Utility............................................... A-1
Appendix B.
Install Audio Driver ......................................................................... B-1
Appendix C.
Install LAN Driver ........................................................................... C-1
Appendix D.
Install USB 2.0 Driver .....................................................................D-1
Appendix E.
BIOS Update Guide ......................................................................... E-1
Appendix F.
Hardware Monitoring (The Winbond Hardware Doctor Utility) .. F-1
Appendix G.
Troubleshooting (Need Assistance?)...............................................G-1
Appendix H.
How to Get Technical Support ........................................................H-1
IS7-V
1
User’s Manual
快速安裝指引
2
快速安裝指引
如您要瞭解此主機板更詳細的資訊,請參閱我們的完整版使用手冊,裡面會有詳盡的說明。此快速
安裝手冊是給有經驗的系統組裝者使用,如果這是您第一次嘗試來組裝您的電腦系統,我們建議您
先去閱讀完整版的使用手冊,或是詢問技術人員來幫助您組裝您的電腦系統。(完整版的使用手冊
已包覆在隨本主機板所附的驅動程式與應用光碟之中。)
安裝處理器的散熱片以及風扇組件
本主機板提供零出力 (Zero Insertion Force, ZIF) 式
Socket 478,以方便安裝 Intel® Pentium® 4 CPU。您
所購買的 CPU 應已配備一組散熱套件及散熱片,
如果沒有,請購買專為 Pentium® 4 Socket 478 設計
的散熱套件及散熱片。
1.
請在主機板上面找出 Socket 478 插座的位置,
然後將固定模組基座固定在主機板上面。
注意:如果您使用專門為英特爾 Pentium® 4 處理器
所設計的機殼,請注意已經安裝在機箱上的金屬螺
栓或是間隔卡樁。請小心不要讓金屬螺栓或是間隔
卡樁接觸到印刷電路板上的線路或是零件。
2.
請將處理器插座的釋放拉桿向插座的外側拉
出,然後將釋放拉桿以 90 度角的角度向上拉
起,然後請您以正確的方向將處理器插入處理
器插座。切勿太過施力地將處理器置入插座,
因為您只能以一個固定的方向來將處理器插
入。當處理器置入到處理器插座之後,請將插
座釋放拉桿再下推到底即可。
3.
請將散熱片面朝下地置放到處理器的上面,直
到散熱片完全地蓋住處理器為止。
4.
將風扇及其固定架機構組件覆蓋至散熱片上
面。請確認風扇及其固定架機構組件四個邊角
的鎖扣都已經卡入固定架的鎖孔位置。
5.
將風扇以及其固定架機構組件兩側的固定架鎖
夾一起向下壓,以將其與固定模組基座上的鎖
孔扣上。
6.
現在風扇及其固定架機構組件、固定模組基座
和當中的散熱片都應該已經牢固地互相緊扣
著。
注意:請不要忘記去設定處理器正確的匯流排頻率和倍頻的數值。
IS7-V
快速安裝指引
3
將主機板安裝到機殼上
當您將處理器安裝到主機板上之後,您便可以開始將主機板固定到電腦機殼裡去。首先;請您先將
主機板固定到電腦機殼。大多數的電腦機殼底座都有許多的固定孔位,請將主機板上的固定孔位與
機殼底座上的固定孔位對準。如果孔能對準並且有螺絲孔,就表示可使用銅柱來固定主機板。另外;
您可以使用塑膠墊片來讓螺絲與主機板的 PCB 表層隔離(絕緣)。
安裝記憶體模組
1.
找出您主機板上 DIMM 插槽的位置。
2.
請您小心地抓住 DIMM 模組的兩側,請勿碰
觸其接點。
3.
請將記憶體模組上的榫子與 DIMM 插槽上的
卡榫對準。
4.
穩固地施壓來將記憶體模組向下插入 DIMM
插槽,直到 DIMM 插槽兩側的模組固定夾自
動地扣入記憶體模組的固定夾缺口為止。切勿太過施力地來將 DIMM 模組插入插槽,因為您
只能以一個固定的方向來插入 DIMM 模組。
5.
要取出 DIMM 模組,請您向外側同時地壓下 DIMM 插槽兩側的模組固定夾,即可將 DIMM 模
組抽取出來。
注意:靜電會造成電腦或是附加卡上電子元件的損壞,在您要進行這些程序之前,請確認您已經藉
由暫時地接觸已接地的金屬物體來放掉您身上所帶有的靜電。
連接器、連接頭以及附加卡的安裝
在任何一部電腦機殼的裡面,都必需連接一些纜線與插頭。這些纜線與插頭通常都是一對一的連接
至主機板的連接埠上,您必需注意任何一條纜線的連接方向。如果可能的話,請一併注意連接埠第
一根針腳的位置。您將會安裝一些特殊功能的附加卡到主機板上面,像是 SCSI 卡或是 AGP 顯示
卡等等。當您將它們安裝到主機板上適當的插槽之後,請以螺絲將這些附加卡與機殼背板牢牢地固
定好,避免有鬆動的情況發生。
如您想要瞭解相關且更為詳細的資訊,請參閱我們的完整版使用手冊,裡面會有詳盡的說明。
將電源供應器的電源線連接頭與主機板上的 ATX12V 電源接頭連接起來
請將電源供應器的 ATX 電源接頭確實地壓入主機板上的 ATX12V 電源接頭,並確定連接妥當。
BIOS 的設定
當您將所有的硬體安裝完畢以後,就可以開啟電腦的電源並進入 BIOS 的選項。如您想要瞭解相關
且更為詳細的資訊,請參閱我們的完整版使用手冊,裡面會有詳盡的說明。
User’s Manual
速いインストールガイド
4
速いインストールガイド
このマザーボードの詳細については、ユーザーズマニュアルの完全版を参照してください。この
クイックインストールガイドは、経験あるシステム構築者向けに書かれました。今回始めてコン
ピュータシステムをセットアップする方は、まず完全版のマニュアルをお読みになるか、専門技
術者に連絡してコンピュータシステムのセットアップを行うようお勧めします。(完全なユーザ
ーズマニュアルはこのマザーボードに付属するドライバとユーティリティ CD を検索して入手
できます。)
CPU ヒートシンクとファンアセンブリの取り付け
このマザーボードは ZIF (ゼロインサーションフ
ォース) Socket 478 を提供して Intel® Pentium® 4
CPU をインストールします。お買い上げになった
CPU には、ヒートシンクと冷却ファンのキットが
付属しています。付属していない場合、Pentium® 4
Socket 478 向けに特別に設計されたキットをお求
めください。
1.
マザーボードに 478 ピン ZIF ソケットが見つ
かったら、リテンションモジュールをマザー
ボードに固定します。
注意:Pentium® 4 マザーボードの用に特別に設計
されたシャーシをご使用の場合、金属製スタッド
やスペーサーがすでにシャーシに取り付けられ
ていれば、その場所に注意してください。金属製
スタッドやスペーサーが PCB の印刷回路線や部
品に接触しないように用心してください。
2.
ソケットから CPU のソケットレバーを横に、
それから 90 度上に引っ張ります。CPU を正
しい方向に差し込みます。CPU は一方向にし
かフィットしないため、CPU を差し込む際に
余分な力をかけないでください。CPU を押さ
えながらソケットレバーを閉めます。
3.
ヒートシンクを CPU にすっぽりかぶせます。
4.
ファンとリテンションメカニズムアセンブリ
をヒートシンクの上に置きます。ファンとリ
テンションメカニズムアセンブリの各サイド
のリテンションロックが、4 つともリテンシ
ョンホールにはめ込まれていることを確認し
てください。
5.
ファンとリテンションメカニズムアセンブリ
の両側にあるリテンションロックを押し下げ
て、リテンションモジュール台にしっかり固定します。
6.
これでファンとリテンションメカニズムアセンブリとリテンションモジュール台の各サイ
ドが、内部のヒートシンクにしっかり固定されました。
IS7-V
速いインストールガイド
5
注意:正しいバス周波数と倍数をプロセッサ用に設定するのを忘れないでください。
マザーボードをシャーシに取り付ける
マザーボードにプロセッサを取り付けた後、シャーシにマザーボードを固定することができるよ
うになります。まず、シャーシにマザーボードを固定する必要があります。ほとんどのコンピュ
ータシャーシには、多くの取り付け穴の付いた台が付属しており、それを使用することでマザー
ボードをしっかり取り付けたり、同時にショートを避けることができます。シャーシに付属する
飾りボタンかスペーサーを使用してマザーボードを固定します。
RAM モジュールの取り付け
1.
ボードの DIMM スロットを探します。
2.
DIMM モジュールの 2 つのエッジがそのコネ
クタに触れないように、注意して持ちます。
3.
モジュールのノッチキーをスロットのリブに
合わせます。
4. モジュールをスロットにしっかり押し込むと、
スロットの両側にあるイジェクタタブが取り
付けノッチにかちっと音を立てて自動的には
め込まれます。DIMM モジュールに余分な力をかけないでください。DIMM モジュールは一
方向にしかフィットしません。
5.
DIMM モジュールは、
スロットの 2 つのイジェクタタブを外側に同時に引っ張ると外れます。
注意:静電気はコンピュータやオプションのボードの電気コンポーネントを損傷させることがあ
ります。これらの手順を開始する前に、アースされた金属物体に軽く触れて静電気を必ず放電し
てください。
コネクタ、ヘッダ、スイッチおよびアダプタ
コンピュータのケース内部には、複数のケーブルやプラグを接続できます。これらのケーブルや
プラグは、通常マザーボードにあるコネクタに 1 つずつ接続されます。ケーブルの接続方向には
十分な注意を払い、また必要に応じ、コネクタの第 1 ピンの位置にも注目する必要があります。
SCSI アダプタ、AGP アダプタのような特殊なニーズ向けには、それに対応したアダプタを取り
付けてください。アダプタをマザーボードのスロットに取り付けたら、ネジでシャーシの背面パ
ネルに固定してください。
詳細については、ユーザーズマニュアルの完全版を参照してください。
電源コネクタを ATX12V 電源コネクタに差し込む
電源装置から出ている電源ブロックコネクタをこの ATX12V 電源に接続します。コネクタが十
分奥まで装着されていることをご確認ください。
BIOS のセットアップ
ハードウェアの取り付けが完了したら、コンピュータの電源をオンにし、BIOS Setup アイテム
に移動して、プロセッサのパラメータをセットアップします。詳細については、ユーザーズマニ
ュアルの完全版を参照してください。
User’s Manual
6
Schneller Installation Führer
Schneller Installation Führer
Beziehen Sie sich bitte für detaillierte Informationen über diese Hauptplatine auf die vollständige Version
des Benutzerbuchs. Diese Schnellinstallationsanleitung ist für erfahrene Systemaufbauer gedacht. Ist es
Ihr erster Versuch ein Computersystem aufzubauen, dann empfehlen wir Ihnen zuerst das vollständige
Benutzerhandbuch zu lesen oder einen Techniker zum Aufbauen des Systems zu Hilfe zu holen. (Ein
komplettes Handbuch finden Sie auf der CD mit den Treibern und Hilfsprogrammen, die diesem
Motherboard beiliegt.)
Installation von CPU-Kühlblech & Lüftereinheit
Dieses Motherboard verfügt über einen ZIF (Zero
Insertion Force) Sockel 478 zur Installation eines
Intel® Pentium® 4 CPU. Ihre CPU sollte über ein
Kühlblech und einen Lüfter verfügen. Wenn dies nicht
der Fall ist, kaufen Sie bitte diese Teile speziell für
den Pentium® 4 Sockel 478.
1.
Finden Sie den 478-polige ZIF-Sockel auf dem
Motherboard. Befestigen Sie die Basis des
Haltemoduls auf dem Motherboard.
Achtung: Wenn Sie ein speziell für den Pentium® 4
konstruiertes Gehäuse verwenden, achten Sie bitte auf
die Lage der Metallbolzen bzw. Abstandhalter, wenn
sie schon im Gehäuse installiert sind. Achten Sie
darauf, dass kein Kontakt zwischen Metallbolzen bzw.
Abstandhalter und den gedruckten Schaltkreisen bzw.
leitfähigen Teilen auf dem PCB entsteht.
2.
Ziehen Sie den Hebel des Prozessorsockels
seitwärts vom Sockel und dann im 90
Grad-Winkel nach oben. Setzen Sie den Prozessor
mit der korrekten Ausrichtung hinein. Wenden
Sie keine Gewalt beim Einsetzen des Prozessors
ein; er passt nur in eine Ausrichtung hinein.
Drücken Sie den Sockelhebel wieder herunter,
während Sie den Prozessor heruntergedrückt
halten.
3.
Setzen Sie das Kühlblech mit der Oberseite nach
unten auf den Prozessor, bis es den Prozessor
völlig abdeckt.
4.
Setzen Sie die Kühlblechabdeckung und die
Haltemechanismus-Einheit auf das Kühlblech.
Vergewissern Sie sich, dass alle vier
Halteklammern zu jeder Seite der Abdeckung in
die Haltelöcher greifen.
5.
Drücken Sie den Halteclip auf beiden Seiten von
Lüfter und Haltemechanismuseinheit nieder, bis er in die Basis des Haltemoduls einschnappt.
6.
Lüfter und Haltemechanismus-Einheit und die Basis des Haltemoduls sollten nun fest miteinander
verriegelt sein und das Kühlblech sich in ihrem Innern befinden..
IS7-V
Schneller Installation Führer
7
Achtung: Vergessen Sie nicht, die korrekte Busfrequenz und -Multiplikator für Ihren Prozessor
einzustellen.
Installieren der Hauptplatine im Gehäuse
Nach der Installation des Prozessors können Sie anfangen die Hauptplatine im Computergehäuse zu
befestigen. Die meisten Gehäuse haben eine Bodenplatte, auf der sich eine Reihe von Befestigungslöcher
befinden, mit deren Hilfe Sie die Hauptplatine sicher verankern können und zugleich Kurzschlüsse
verhindern. Verwenden Sie entweder die Dübeln oder die Abstandhalter, um die Hauptplatine auf der
Bodenplatte des Gehäuses zu befestigen.
Installation der RAM-Module
1.
Finden Sie den DIMM-Steckplatz auf dem Board.
2.
Halten Sie ie beiden Ränder des DIMM-Moduls
vorsichtig fest, wobei Sie darauf achten, nicht die
Anschlüsse zu berühren.
3.
Richten Sie die Nut am Modul mit der Erhöhung
am Steckplatz aus.
4.
Drücken Sie das Modul fest in die Steckplätze,
bis die Auswurflaschen zu beiden Seiten des
Steckplatzes
automatisch
in
die
Befestigungskerbe einschnappen. Wenden Sie keine Gewalt beim Einsetzen des DIMM-Moduls an;
es paßt nur in eine Richtung hinein.
5.
Zum Ausbau der Module drücken Sie die beiden Auswurflaschen auf dem Steckplatz nach außen
zusammen und ziehen das Modul heraus.
Anschlüsse, Sockel, Schalter und Adapter
Im Inneren des Gehäuses findet man in jedem Computer viele Kabel und Stecker, die angeschlossen
werden müssen. Diese Kabel und Stecker werden normalerweise einzeln mit den Anschlüssen auf der
Hauptplatine verbunden. Sie müssen genau auf die Anschlussorientierung der Kabel achten und, wenn
vorhanden, sich die Position des ersten Pols des Anschlusses merken. Wenn Sie Adapter wie z.B.
SCSI-Adapter, AGP-Adapter usw. installieren, befestigen Sie bitte die Adapter immer mit Hilfe der
Schrauben auf die Rückseite des Computergehäuses.
Für detaillierte Informationen beziehen Sie sich bitte auf das vollständige Benutzerhandbuch.
Verbinden der Netzstecker mit dem ATX12V-Anschluss
Denken Sie daran, den Anschluss des ATX-Netzteils fest in das Ende mit dem ATX12V-Anschluss zu
drücken, um eine feste Verbindung zu garantieren.
BIOS-Setup
Schalten Sie nach der vervollständigten Hardwareinstallation den Computer ein und gehen zur Option im
BIOS, um die Prozessorparameter einzustellen. Für detaillierte Informationen beziehen Sie sich bitte auf
das vollständige Benutzerhandbuch.
User’s Manual
8
Guide Rapide d'Installation
Guide Rapide d'Installation
Pour des informations relatives à cette carte mère plus détaillées, veuillez vous référer à notre version
complète du manuel utilisateur. Ce guide d’installation rapide est créé pour les assembleurs système
expérimentés. S’il s’agit de votre premier essai pour installer un ordinateur, nous vous suggérons de lire
d’abord le manuel en version complète ou de demander l’aide d’un technicien pour vous aider à
configurer le système ordinateur. (Un manuel de l'utilisateur complet est disponible en naviguant dans le
CD des pilotes et utilitaires fournis avec la carte mère.)
Installer le Dissipateur de Chaleur du CPU et l’Assemblage du Ventilateur
Cette carte mère fournit un support ZIF (Zero
Insertion Force) Socket 478 permettant d'installer le
Pentium®
4.
Le
Microprocesseur
Intel®
microprocesseur que vous achetez doit être muni d'un
système de refroidissement avec dissipateur thermique
et ventilateur. Dans le cas contraire, veuillez en
acheter un, conçu spécialement pour les
microprocesseurs Pentium® 4 Socket 478.
1.
Localisez le socle ZIF 478-broches sur la
carte-mère. Serrez la Base du Module de
Rétention sur la carte.
Attention: Si vous utilisez un châssis spécialement
conçu pour Pentium® 4, veuillez faire attention à
l’emplacement des Clous en Métal ou des Espaceurs
installés sur le châssis. Ne laissez jamais les Clous en
Métal ou les Espaceurs entrer en contact des circuits
imprimés ou des composants sur le PCB.
2.
Tirez le levier du socle CPU sur les côtés jusque
sur un angle d’environs 90. Insérez le CPU avec
l’orientation correcte. N’utilisez pas trop de force
pour insérer le CPU; il n’ira que selon une seule
orientation. Refermez ensuite le levier du socle
tout en maintenant le CPU.
3.
Placez le dissipateur de chaleur face vers le bas
dans le CPU jusqu’à ce qu’il recouvre celui-ci
complètement.
4.
Placez le Ventilateur et l’Assemblage du
Mécanisme de Retient dans le dissipateur de
chaleur. Assurez-vous que les quatre Verrous de
Retient sur chaque côté du Ventilateur et du
Mécanisme de Retient dans les Trous de Retient.
5.
Pressez le Verrou de Retient sur les deux côtés du
Ventilateur et du Mécanisme de Retient pour
verrouiller ensemble avec la Base du Module de Retient.
6.
Le Ventilateur, le Mécanisme de Retient et la Base du Module de Retient doivent maintenant être
verrouillés l’un sur l’autre avec le dissipateur de chaleur à l’intérieur.
IS7-V
Guide Rapide d'Installation
9
Attention: N’oubliez pas de programmer la fréquence de bus correcte et le multiple pour votre
processeur.
Installer la Carte Mre dans le Châssis
Une fois que vous aurez installé le processeur sur la carte mère, vous pourrez commencer à fixer la carte
mère sur le châssis. Tout d’abord, vous avez besoin de fixer la carte mère sur le châssis. La plupart des
châssis d’ordinateur possèdent une base sur laquelle il y a nombreux trous de montage permettant à la
carte mère d’être fixée fermement, et en même temps d’éviter les court-circuits. Utilisez les talons ou les
entretoises fixés sur le châssis pour fixer la carte mère.
Installer des Modules RAM
1.
Localisez le socle DIMM sur la carte.
2.
Maintenez les deux bords du module DIMM avec
précaution, en évitant de toucher ses connecteurs.
3.
Alignez la touche du cran avec la ligne sur le
socle.
4.
Pressez fermement le module dans les socles
jusqu’à ce que les languettes d’éjection sur les
deux côtés du socle aillent automatiquement dans
le cran de montage. Ne forcez pas à l’excès sur le
module DIMM car celui-ci ne peut aller que selon
une seule orientation.
5.
Pour enlever des modules DIMM, pressez simultanément les deux languettes d’éjection sur le socle,
puis sortez le module DIMM.
Attention: L’électricité statique risque d’endommager les composants électroniques de l’ordinateur ou
des cartes optionnelles. Avant de commencer ces procédures, assurez-vous de bien décharger toute
l’électricité statique en touchant rapidement un objet métallique relié au sol.
Connecteurs, Socles de connexion, Interrupteurs et Adaptateurs
A l’intérieur du boîtier de n’importe quel ordinateur il y a plusieurs câbles et prises qui doivent être
connectés. Ces câbles et prises sont habituellement connectés les uns après les autres aux connecteurs
situés sur la carte mère. Vous avez besoin de faire attention au sens de connexion des câbles et, s’il y a
lieu, remarquez la position de la première broche du connecteur. Vous installerez certains adaptateurs
pour des besoins spéciaux, tels adaptateurs SCSI, adaptateurs AGP, etc. Lorsque vous les installez dans
les emplacements situés sur la carte mère, veuillez les fixer sur le panneau arrière du châssis à l'aide des
vis.
Pour les informations détaillées, veuillez vous référer au manuel utilisateur en version complète.
Brancher les connecteurs d'alimentation dans les connecteurs ATX12V
Souvenez-vous que vous devez pousser le connecteur de votre alimentation fermement dans le connecteur
ATX12V pour assurer une bonne connexion.
Configuration du BIOS
Une fois le matériel installé complètement, démarrez l'ordinateur et allez sur l'item dans le BIOS pour
configurer les paramètres du processeur. Pour les informations détaillées, veuillez vous référer à la
version complète du manuel utilisateur.
User’s Manual
10
Быстро Направляющий выступ Установки
Быстро Направляющий выступ Установки
Более подробные сведения о материнской плате приведены в руководстве пользователя. Краткое
руководство по установке предназначено для опытных специалистов. Если вы собираете
компьютер впервые, ознакомьтесь сперва с руководством пользователя или попросите техника
помочь в настройке компьютерной системы.
Установка радиатора и вентилятора охлаждения процессора
На этой системной плате используется гнездо ZIP
(с нулевым усилием установки) типа 'Socket 478'
для процессора Intel® Pentium® 4. В комплект
приобретаемого процессора должны входить
радиатор и вентилятор. В противном случае
следует приобрести радиатор
и вентилятор,
предназначенные для процессора Pentium® 4 с
разъемом 'Socket 478'.
1.
Найдите на системной плате 478-выводной
разъем типа ZIF. Закрепите основание
радиатора на системной плате.
Внимание: Устанавливая плату в корпус,
разработанный специально для Pentium® 4,
обратите внимание на уже установленный крепеж
(металлические стойки, зажимы). Убедитесь, что
установленный крепеж не касается системной
платы или ее выводов.
2.
Оттяните рычаг фиксации процессора в
сторону и поднимите его на 90 градусов вверх.
Расположив процессор соответствующим
образом, вставьте его в разъем. Не прилагайте
излишних усилий, чтобы вставить процессор.
Процессор легко устанавливается, если вы
правильно совместили его с разъемом.
Установив
процессор,
опустите
рычаг
фиксации процессора на место.
3.
Положите на процессор радиатор так, чтобы
он полностью накрывал процессор.
4.
Положите на радиатор вентилятор и
фиксирующий механизм. Убедитесь, что все
четыре
фиксатора
вентилятора
и
фиксирующего
механизма
вошли
в
предназначенные отверстия и защелкнулись.
5.
Зафиксируйте вентилятор на основании
радиатора, опустив рычажки, расположенные с обеих сторон фиксирующего механизма.
6.
Вентилятор, фиксирующий механизм и основание радиатора должны быть надежно
закреплены вместе с вентилятором.
IS7-V
Быстро Направляющий выступ Установки
11
Внимание: Установите соответствующие частоту и кратность шины процессора.
Установка материнской платы в корпус
После установки процессора на материнскую плату можно начинать установку материнской
платы в корпус. Большая часть корпусов оборудована основанием, в котором проделаны
монтажные отверстия, которые позволяют надежно закрепить материнскую плату и предотвратить
короткие замыкания. Для крепления материнской платы к основанию используются винты и
прокладки.
Установка модулей памяти
1.
Найдите на системной плате разъем для
модулей памяти DIMM.
2.
Аккуратно, за два конца, возьмите модуль
памяти, не касаясь контактов.
3.
Совместите выемку в модуле памяти с
выступом в разъеме.
4.
Нажмите на модуль так, чтобы лепестки
выталкивателя с обеих сторон разъема
автоматически защелкнулись и вошли в пазы. Не применяйте при установке излишнюю силу.
Модуль входит в разъем только в одном положении.
5.
Для извлечения модулей памяти DIMM одновременно нажмите на лепестки выталкивателя и
вытащите модуль.
Внимание: Статическое электричество может стать причиной выхода из строя электронных
компонентов компьютера. Перед началом данной процедуры снимите с себя статический заряд,
коснувшись заземленного металлического предмета.
Разъемы, переключатели и адаптеры
Внутри корпуса компьютера необходимо расположены несколько кабелей и вилок, которые
необходимо подключить. Обычно эти кабели подключаются к разъемам, расположенным на
материнской плате. При подключении любого кабеля необходимо обращать внимание на
расположение первого контакта разъема. Для особых целей могут потребоваться специальные
адаптеры, например, адаптер SCSI, адаптер AGP и т.п.. При установке адаптеров в гнезда
материнской платы закрепите их на задней панели с помощью винтов.
За более подробной информацией обращайтесь к полному руководству пользователя.
Подключение кабелей питания к разъемам ATX12V
Обратите внимание, разъем блока питания ATX необходимо вставить в разъем ATX12V до упора,
чтобы обеспечить надежное соединение.
Настройка BIOS
По окончании установки аппаратуры включите питание и перейдите в меню BIOS Setup, чтобы
настроить параметры процессора. За более подробной информацией обращайтесь к руководству
пользователя.
User’s Manual
12
Guida Rapida Dell'Installazione
Guida Rapida Dell'Installazione
Per maggiori e dettagliate informazioni su questa scheda madre si prega di fare riferimento alla versione
integrale del Manuale utente. Questa guida all’installazione veloce è intesa per costruttori esperi di
sistemi. Se questa è la prima volta che si cerca di installare un sistema, si consiglia di leggere, innanzi
tutto, la versione integrale del manuale oppure di chiedere aiuto ad un tecnico per l’installazione.
Installare il dispersore di calore CPU ed il gruppo della ventolina
Questa scheda madre fornisce una presa “Socket 478”
ZIF (Zero Insertion Force – forza d’inserimento zero)
per installare il processore Intel® Pentium® 4. Il
processore acquistato dovrebbe essere fornito di
dispersore di calore e ventolina per il raffreddamento.
In caso contrario acquistare un dispersore di calore
specifico per la presa Socket 478 Pentium®.
1. Ubicare la presa ZIF a 478 pin sulla scheda madre.
Stringere la base del modulo di trattenimento
sulla scheda madre.
Attenzione: Se si impiega un telaio progettato
specificatamente per il processore Pentium® 4, si
prega prestare attenzione all’ubicazione delle
guarnizioni metalliche o degli spaziatori, nel caso in
cui siano già installati sul telaio. Assicurarsi di non
permettere alle guarnizioni metalliche od agli
spaziatori di entrare in contatto con il cavo o con le
parti del circuito sul PCB.
2.
Tirare di lato la leva della presa CPU,
allontanandola dalla presa; poi sollevarla di 90
gradi. Inserire la CPU con l’orientamento corretto.
Non sforzare per inserire la CPU poiché si adatta
solamente in un dato orientamento. Chiudere la
leva della presa trattenendo la CPU.
3.
Mettere il dispersore di calore a faccia in giù sulla
CPU finché la copre completamente.
4.
Mettere la ventolina ed il gruppo del meccanismo
di trattenimento sul dispersore di calore.
Assicurarsi che tutti i quattro fermi di
trattenimento, su ciascun lato della ventolina e del
gruppo del meccanismo di trattenimento, scattino
in posizione nei fori ti trattenimento.
5.
Spingere verso il basso i fermi di trattenimento su
entrambi i lati della ventolina e del gruppo del meccanismo di trattenimento per fissarli con la base
del modulo di trattenimento.
6.
La ventolina, il gruppo del meccanismo di trattenimento e la base del modulo di trattenimento ora
dovrebbero essere fissati gli uni agli altri trattenendo al loro interno il dispersore di calore.
IS7-V
Guida Rapida Dell'Installazione
13
Attenzione: Non dimenticare di impostare la corretta frequenza multipla e BUS per il processore.
Installazione della scheda madre sul telaio
Dopo avere installato il processore sulla scheda madre si può iniziare a fissare la scheda madre sul telaio.
Innanzi tutto è necessario fissare la scheda madre al telaio. La maggior parte dei telai ha una base sulla
quale sono presenti diversi fori di montaggio che permettono di fissare in modo accurato la scheda madre
e, allo stesso tempo, di prevenire corto circuiti. Impiegare le borchie o gli spaziatori attaccati al telaio per
fissare la scheda madre.
Installare i moduli RAM
1.
Ubicare gli alloggiamenti DIMM sulla scheda.
2.
Tenere con delicatezza i lati del modulo DIMM
senza toccare i connettori.
3.
Allineare la tacca sul modulo con la nervatura
dell’alloggiamento.
4.
Premere
con
fermezza
il
modulo
nell’alloggiamento
finché
le
linguette
d’espulsione su entrambi i lati dell’alloggiamento
scattano sulla tacca di montaggio. Non forzare eccessivamente il modulo DIMM perché quest’ultimo
si adatta solamente in una direzione.
5.
Per rimuovere i moduli DIMM spingere contemporaneamente le due linguette d’espulsione
sull’alloggiamento, poi estrarre il modulo DIMM.
Attenzione: L’elettricità statica può danneggiare i componenti elettronici del computer o delle schede.
Prima di iniziare queste procedure, assicurarsi di avere scaricato completamente l’elettricità statica
toccando brevemente un oggetto metallico con massa a terra.
Connettori, collettori, interruttori ed adattatori
All’interno della copertura di ogni computer ci sono diversi cavi e prese che devo essere collegati. Questi
cavi e prese sono solitamente collegati uno ad uno ai connettori situati sulla scheda madre. E’ necessario
prestare particolare attenzione a qualunque orientamento del collegamento che possono avere i cavi e, se
necessario, notare la posizione del primo pin del connettore. Si installeranno alcuni adattatori per
particolari necessità quali l’adattatore SCSI, AGP, eccetera. Quando si installano gli adattatori sugli slot
della scheda madre, si ricorda di fissarli con le viti anche sul pannello posteriore del telaio.
Per informazioni dettagliate si prega di fare riferimento alla versione integrale del Manuale utente.
Collegamento dei connettori d’alimentazione ai connettori ATX12V
Ricordarsi che è necessario spingere con fermezza fino in fondo il connettore della sorgente
d’alimentazione ATX al connettore ATX12V, assicurando così un buon collegamento.
Impostazione BIOS
Quando l’hardware è stato installato completamente, accendere il computer ed andare alla voce BIOS per
impostare i parametri del processore. Per informazioni dettagliate si prega di fare riferimento alla versione
integrale del Manuale utente.
User’s Manual
14
IS7-V
Introduction
1-1
Chapter 1. Introduction
1-1. Features & Specifications
1. CPU
•
•
Supports Intel Pentium 4 Socket 478 processor with 800/533/400MHz System Data Bus
Supports Intel Hyper-Threading Technology
2. Chipset
•
•
Intel 82848P (MCH) + 82801EB (ICH5)
Supports Advanced Configuration Power Interface (ACPI)
3. Memory
•
•
2x 184-pin DIMM sockets
Supports 2 DIMM Single Channel DDR 400/333 (Max. 2GB)
4. AGP
•
Accelerated Graphics Port connector supports AGP PRO 8X/4X Interface (0.8V/1.5V)
5. Serial ATA
•
Onboard 2 channels of Serial ATA 150MB/s data transfer rate via ICH5 South Bridge
6. LAN
•
Onboard 10/100M LAN Controller
7. USB 2.0
•
8x USB 2.0 ports support 480 Mb/s data transfer rate
8. Audio
•
•
Onboard 6-Channel AC 97 CODEC
Professional digital audio interface supports 24-bit S/PDIF Output
9. Internal I/O Connectors
•
•
•
•
•
•
•
1x AGP slot
5x PCI slots
1x Floppy port supports up to 2.88MB
2x Ultra ATA/100/66/33 connectors
2x Serial ATA 150 connectors
2x USB 2.0 headers
1x CD-IN, 1x AUX-IN header
10. Back Panel I/O
•
•
•
1x PS/2 Keyboard, 1x PS/2 mouse
1x Serial port connector, 1x Parallel port connector
1x S/PDIF Out connector
User’s Manual
1-2
Chapter 1
•
•
•
•
1x AUDIO1 connector (Rear-Left / Rear-Right, Center/Subwoofer)
1x AUDIO2 connector (Mic-In, Line-In, Front-Left/Front-Right)
2x USB connectors
2x USB connectors, 1x RJ-45 LAN connector
11. Miscellaneous
•
•
IS7-V
ATX form factor
Hardware Monitoring - Including Fan speed, Voltages, CPU and System temperature
Specifications and information contained herein are subject to change without notice.
Introduction
1-3
1-2. Layout Diagram
User’s Manual
1-4
IS7-V
Chapter 1
Hardware Setup
2-1
Chapter 2. Hardware Setup
Before the Installation: Turn off the power supply switch (fully turn off the +5V standby power), or
disconnect the power cord before installing or unplugging any connectors or add-on cards. Failing to do
so may cause the motherboard components or add-on cards to malfunction or damaged.
2-1. Install The Motherboard
Most computer chassis have a base with many mounting holes to allow motherboard to be securely
attached on and at the same time, prevented from short circuits. There are two ways to attach the
motherboard to the chassis base:
1. use with studs
2. or use with spacers
In principle, the best way to attach the board is
to use with studs. Only if you are unable to do
this should you attach the board with spacers.
Line up the holes on the board with the mounting
holes on the chassis. If the holes line up and there
are screw holes, you can attach the board with
studs. If the holes line up and there are only slots,
you can only attach with spacers. Take the tip of
the spacers and insert them into the slots. After
doing this to all the slots, you can slide the board
into position aligned with slots. After the board has been positioned, check to make sure everything is OK
before putting the chassis back on.
ATTENTION: To prevent shorting the PCB circuit, please REMOVE the metal studs or spacers if they
are already fastened on the chassis base and are without mounting-holes on the motherboard to align with.
User’s Manual
2-2
Chapter 2
2-2. Install Pentium® 4 CPU and Heatsink Supporting-Base
This motherboard provides a ZIF (Zero Insertion
Force) Socket 478 to install Intel® Pentium® 4
CPU. The CPU you bought should have a kit of
heatsink and cooling fan along with. If that’s not
the case, buy one specially designed for Pentium®
4 Socket 478.
1.
Locate the 478-pin ZIF socket on the
motherboard. Fasten the Retention Module
Base onto the motherboard.
ATTENTION: If you are using chassis specially
designed for Pentium® 4, please pay attention to
the location of metal studs or spacers if they are
already installed on the chassis. Be careful not let
the metal studs or spacers contact the printed
circuit wire or parts on the PCB.
2.
Pull the CPU socket lever sideways away
from the socket and then upwards to 90
degree. Insert the CPU with the correct
orientation. Do not use extra force to insert
CPU; it only fits in one orientation. Close
down the socket lever while holding down
the CPU.
3.
Put the heatsink faces down onto the CPU
until it completely covers the CPU.
4.
Put the Fan and Retention Mechanism
Assembly onto the heatsink. Make sure all
the four Retention Locks at each side of the
Fan and Retention Mechanism Assembly
snap into the Retention Holes.
5.
Push down the Retention Lock at both sides
of the Fan and Retention Mechanism
Assembly to lock up together with the
Retention Module Base.
6.
The Fan and Retention Mechanism Assembly
and Retention Module Base should now
firmly lock up with each other with the heatsink inside.
ATTENTION: Do not forget to set the correct bus frequency and multiple for your processor.
IS7-V
Hardware Setup
2-3
2-3. Install System Memory
This motherboard provides 2 184-pin DDR DIMM sites for memory expansion available from minimum
128MB to maximum 2GB.
Table 2-1. Valid Memory Configurations
Bank
Memory Module
Total Memory
Bank 0, 1 (DIMM1)
128, 256, 512MB, 1GB
128MB ~ 1GB
Bank 2, 3 (DIMM2)
128, 256, 512MB, 1GB
128MB ~ 1GB
Total System Memory
128MB ~ 2GB
NOTE: No hardware or BIOS setup required after adding or removing memory modules.
Power off the computer and unplug the AC power cord before installing or removing memory modules.
1.
Locate the DIMM slot on the board.
2.
Hold two edges of the DIMM module
carefully, keep away of touching its
connectors.
3.
Align the notch key on the module with the
rib on the slot.
4.
Firmly press the module into the slots until
the ejector tabs at both sides of the slot
automatically snaps into the mounting notch.
Do not force the DIMM module in with extra
force as the DIMM module only fit in one direction.
5.
To remove the DIMM modules, push the two ejector tabs on the slot outward simultaneously, and
then pull out the DIMM module.
ATTENTION: Static electricity can damage the electronic components of the computer or optional
boards. Before starting these procedures, ensure that you are discharged of static electricity by touching a
grounded metal object briefly.
User’s Manual
2-4
Chapter 2
2-4. Connectors, Headers and Switches
Here we will show you all of the connectors, headers and switches, and how to connect them. Please read
the entire section for necessary information before attempting to finish all the hardware installation inside
the computer chassis. A complete enlarged layout diagram is shown in Chapter 1 for all the position of
connectors and headers on the board that you may refer to.
WARNING: Always power off the computer and unplug the AC power cord before adding or removing
any peripheral or component. Failing to so may cause severe damage to your motherboard and/or
peripherals. Plug in the AC power cord only after you have carefully checked everything.
(1). ATX Power Input Connectors
This motherboard provides two power connectors to connect to an ATX12V power supply with 300W,
20A +5VDC, and 720mA +5VSB capacity at least.
IS7-V
Hardware Setup
2-5
(2). FAN Connectors
These 3-pin connectors each provide power to the cooling fans installed in your system.
The CPU must be kept cool by using a powerful fan with heatsink. The system is capable of monitoring
the speed of the CPU fan.
•
CPU FAN: CPU Fan
•
SYS FAN: System Fan
•
AUX FAN: Auxiliary Fan
WARNING: These fan connectors are not jumpers. DO NOT place jumper caps on these connectors.
User’s Manual
2-6
Chapter 2
(3). CMOS Memory Clearing Header
This header uses a jumper cap to clear the CMOS memory.
•
Pin 1-2 shorted (default): Normal operation.
•
Pin 2-3 shorted: Clear CMOS memory.
WARNING: Turn the power off first (including the +5V standby power) before clearing the CMOS
memory. Failing to do so may cause your system to work abnormally or malfunction.
IS7-V
Hardware Setup
2-7
(4). Front Panel Audio Connection Header
This header provides the connection to audio connector at front panel.
•
To use the audio connector at front panel, remove all the jumpers on this header, and then connect
to front panel by the extension cable provided with the chassis.
•
To use the audio connector at rear panel, disconnect the extension cable, attach the jumpers back at
pin 5-6, and pin 9-10 (default setting).
Pin
1
3
5
7
9
11
13
Pin Assignment
Audio Mic.
Audio Mic. Bias
Speaker Out Right
Channel
X
Speaker Out Left
Channel
Ground
VCC
Pin
2
4
6
8
10
12
14
Pin Assignment
Ground
VCC
Speaker Out Right
Channel Return
NC
Speaker Out Left
Channel Return
S/PDIF In
S/PDIF Out
User’s Manual
2-8
(5).
Chapter 2
Front Panel Switches & Indicators Headers
This header is used for connecting switches and LED indicators on the chassis front panel.
Watch the power LED pin position and orientation. The mark “+” align to the pin in the figure below
stands for positive polarity for the LED connection. Please pay attention to connect these headers. A
wrong orientation will only cause the LED not lighting, but a wrong connection of the switches could
cause system malfunction.
•
HLED (Pin 1, 3):
Connects to the HDD LED cable of chassis front panel.
•
RST (Pin 5, 7):
Connects to the Reset Switch cable of chassis front panel.
•
SPK (Pin 15, 17, 19, 21):
Connects to the System Speaker cable of chassis.
•
SLED (Pin 2, 4):
Connects to the Suspend LED cable (if there is one) of chassis front panel.
•
PWR-ON (Pin 6, 8):
Connects to the Power Switch cable of chassis front panel.
•
PLED (Pin 16, 18, 20):
Connects to the Power LED cable of chassis front panel.
IS7-V
Hardware Setup
2-9
(6). Additional USB Port Headers
These headers each provide 2 additional USB 2.0 ports connection through an USB cable designed for
USB 2.0 specifications.
Pin
Pin Assignment
Pin
1
VCC
2
Pin Assignment
VCC
3
Data0 -
4
Data1 -
5
Data0 +
6
Data1 +
7
Ground
8
Ground
9
NC
10
NC
User’s Manual
2-10
Chapter 2
(7). System Management Bus Headers
This header is reserved for system management bus (SM bus). The SM bus is a specific implementation
of an I2C bus. I2C is a multi-master bus, which means that multiple chips can be connected to the same
bus and each one can act as a master by initiating a data transfer. If more than one master simultaneously
tries to control the bus, an arbitration procedure decides which master gets priority.
(8). Internal Audio Connectors
These connectors connect to the audio output of internal CD-ROM drive or add-on card.
IS7-V
Hardware Setup
2-11
(9). Accelerated Graphics Port Slot
This slot supports an optional AGP graphics card up to AGP 8X mode. Please refer to our Web site for
more information on graphics cards.
ATTENTION: This motherboard does not support 3.3V AGP cards. Use only 1.5V or 0.8V AGP cards.
User’s Manual
2-12
Chapter 2
(10). Floppy Disk Drive Connector
This connector supports two standard floppy disk drives via a 34-pin 34-conductor ribbon cable.
Connecting the Floppy Disk Drive Cable:
1.
Install one end of the ribbon cable into the FDC1 connector. The colored edge of the ribbon cable
should be aligned with pin-1 of FDC1 connector.
2.
Install the other end(s) of ribbon cable into the disk drive connector(s). The colored edge of the
ribbon cable should be also aligned with pin-1 of disk drive connector. The endmost connector
should be attached to the drive designated as Drive A.
IS7-V
Hardware Setup
2-13
(11). IDE Connectors
This motherboard provides two IDE ports to connect up to four IDE drives at Ultra ATA/100 mode by
Ultra ATA/66 ribbon cables. Each cable has 40-pin 80-conductor and three connectors, providing two
hard drives connection with motherboard. Connect the single end (blue connector) at the longer length of
ribbon cable to the IDE port on motherboard, and the other two ends (gray and black connector) at the
shorter length of the ribbon cable to the connectors on hard drives.
If you want to connect two hard drives together through one IDE channel, you must configure the second
drive to Slave mode after the first Master drive. Please refer to the drives’ documentation for jumper
settings. The first drive connected to IDE1 is usually referred to as “Primary Master”, and the second
drive as “Primary Slave”. The first drive connected to IDE2 is referred to as “Secondary Master” and the
second drive as “Secondary Slave”.
Keep away from connecting one legacy slow speed drive, like CD-ROM, together with another hard drive
on the same IDE channel; this will drop your integral system performance.
User’s Manual
2-14
Chapter 2
(12). Serial ATA Connectors
These connectors are provided to attach one Serial ATA device at each channel via Serial ATA cable.
For more information on how to configure the function mode for SATA1 and SATA2, please refer to the
item “Serial ATA 1 Mode” and “Serial ATA 2 Mode” in the BIOS menu of “OnChip IDE Device”.
IS7-V
Hardware Setup
2-15
(13). Back Panel Connectors
•
Mouse: Connects to PS/2 mouse.
•
Keyboard: Connects to PS/2 keyboard.
•
LPT1: Connects to printer or other devices that support this communication protocol.
•
COM1: Connects to external modem, mouse or other devices that support this communication
protocol.
•
OPT2: This connector provides an S/PDIF out connection through optical fiber to digital
multimedia devices.
•
AUDIO1:
R.L./R.R. (Rear Left / Rear Right): Connects to the rear left and rear right channel in the 5.1
channel audio system.
Cen./Sub. (Center / Subwoofer): Connects to the center and subwoofer channel in the 5.1 channel
audio system.
•
AUDIO2:
Mic In: Connects to the plug from external microphone.
Line In: Connects to the line out from external audio sources.
F.L./F.R. (Front Left / Front Right): Connects to the front left and front right channel in the
5.1-channel or regular 2-channel audio system.
•
LAN: Connects to Local Area Network.
•
USB1/USB2: Connects to USB devices such as scanner, digital speakers, monitor, mouse,
keyboard, hub, digital camera, joystick etc.
User’s Manual
2-16
IS7-V
Chapter 2
BIOS Setup
3-1
Chapter 3. BIOS Setup
This motherboard provides a programmable EEPROM that you can update the BIOS utility. The BIOS
(Basic Input/Output System) is a program that deals with the basic level of communication between
processor and peripherals. Use the BIOS Setup program only when installing motherboard, reconfiguring
system, or prompted to “Run Setup”. This chapter explains the Setup Utility of BIOS utility.
After powering up the system, the BIOS message appears on the screen, the memory count begins, and
then the following message appears on the screen:
PRESS DEL TO ENTER SETUP
If this message disappears before you respond, restart the system by pressing <Ctrl> + <Alt> + <Del>
keys, or by pressing the Reset button on computer chassis. Only when it failed by these two methods can
you restart the system by powering it off and then back on.
After pressing <Del> key, the main menu screen appears.
NOTE: In order to increase system stability and performance, our engineering staffs are constantly
improving the BIOS menu. The BIOS setup screens and descriptions illustrated in this manual are for
your reference only, may not completely match what you see on your screen.
User’s Manual
3-2
Chapter 3
3-1. SoftMenu Setup
The SoftMenu utility is ABIT’s exclusive and ultimate solution in programming the CPU operating speed.
All the parameters regarding CPU FSB speed, multiplier factor, the AGP & PCI clock, and even the CPU
core voltage are all available at your fingertips.
Brand Name:
This item displays the CPU model name, for example: Intel Pentium (R) 4.
Frequency:
This item displays the processor speed.
Cache Size:
This item displays the L2 cache size of your CPU.
CPU Operating Speed:
This item displays the CPU operating speed according to the type and speed of your CPU. You can also
select the [User Define] option to enter the manual option.
User Define:
WARNING: The wrong settings of the multiplier and external clock in certain circumstances may cause
CPU damage. Setting the working frequency higher than the PCI chipset or processor specs, may cause
abnormal memory module functioning, system hangs, hard disk drive data lose, abnormal functioning of
the VGA card, or abnormal functioning with other add-on cards. Using non-specification settings for your
CPU is not the intention of this explanation. These should be used for engineering testing, not for normal
applications.
There will be no guaranty for the settings beyond specification, any damage of any component on this
motherboard or peripherals result therein is not our responsibility.
Ext. Clock (CPU/AGP/PCI):
This item selects the external clock frequency.
IS7-V
BIOS Setup
3-3
Multiplier Factor:
This item selects the multiplier factors for your CPU if it is not locked.
Estimated new CPU clock:
This item displays the frequency sum up from the previous item [Ext. Clock] and [Multiplier Factor].
N/B Strap CPU As:
This item sets the external hardware reset strap assigned to MCH (Memory Controller Hub). The options
are: [PSB400], [PSB533], [PSB800], and [By CPU]. The default setting is By CPU.
To set this option manually:
•
Select [PSB400] for CPU of 100MHz FSB frequency.
•
Select [PSB533] for CPU of 133MHz FSB frequency.
•
Select [PSB800] for CPU of 200MHz FSB frequency.
DRAM Ratio (CPU:DRAM):
This item determines the frequency ratio between CPU and DRAM.
AGP Ratio (CPU:AGP:PCI):
This item determines the ratio among CPU, AGP, and PCI.
Fixed AGP/PCI Frequency:
This item determines the AGP/PCI bus frequency. This option allows you to keep your AGP/PCI clock at
some fixed frequency to improve system stability.
CPU Power Supply:
This option allows you to switch between CPU default and user-defined voltages. Leave this setting to
default unless the current CPU type and voltage setting cannot be detected or is not correct. The option
“User Define” enables you to select the Core Voltage manually.
CPU Core Voltage:
This item selects the CPU core voltage.
ATTENTION: A wrong voltage setting may cause the system unstable or even damage the CPU. Please
leave it to default settings unless you are fully aware of its consequences.
DDR SDRAM Voltage:
This item selects the voltage for DRAM slot.
AGP Voltage:
This item selects the voltage for AGP slot.
User’s Manual
3-4
Chapter 3
3-2. Standard CMOS Features
This section contains the basic configuration parameters of the BIOS. These parameters include date,
hour, VGA card, FDD and HDD settings.
Date (mm:dd:yy):
This item sets the date you specify (usually the current date) in the format of [Month], [Date], and [Year].
Time (hh:mm:ss):
This item sets the time you specify (usually the current time) in the format of [Hour], [Minute], and
[Second].
IDE Channel 1 Master/Slave, IDE Channel 2 Master/Slave, IDE Channel
3 Master, IDE Channel 4 Master:
Click <Enter> key to enter its submenu:
NOTE: Item “IDE Channel 3 Master” and “IDE Channel 4 Master” appears only when the item “OnChip
Serial ATA” in the “OnChip IDE Device” menu is set as [Enhanced Mode].
IS7-V
BIOS Setup
3-5
IDE HDD Auto-Detection:
This item allows you to detect the parameters of IDE drives by pressing <Enter> key. The parameters will
be shown on the screen automatically.
IDE Channel 1 Master/Slave, IDE Channel 2 Master/Slave, Extended IDE Drive:
When set to [Auto], the BIOS will automatically check what kind of IDE drive you are using. If you want
to define your own drive by yourself, set it to [Manual] and make sure you fully understand the meaning
of the parameters. Please refer to the instruction manual provided by the device’s manufacturer to get the
setting right.
Access Mode:
This item selects the mode to access your IDE devices. Leave this item to its default [Auto] setting to
detect the access mode of your HDD automatically.
Capacity:
This item displays the approximate capacity of the disk drive. Usually the size is slightly greater than the
size of a formatted disk given by a disk-checking program.
Cylinder:
This item configures the numbers of cylinders.
Head:
This item configures the numbers of read/write heads.
Precomp:
This item displays the number of cylinders at which to change the write timing.
Landing Zone:
This item displays the number of cylinders specified as the landing zone for the read/write heads.
Sector:
This item configures the numbers of sectors per track.
Back to Standard CMOS Features Setup Menu:
Drive A & Drive B:
This item sets the type of floppy drives (usually only Drive A) installed.
Floppy 3 Mode Support:
This item allows you to use “3 Mode Floppy Drive” in Japanese computer system by selecting drive A, B,
or both. Leave this item to its default [Disabled] setting if you are not using this Japanese standard floppy
drive.
Video:
This item selects the type of video adapter used for the primary system monitor.
User’s Manual
3-6
Chapter 3
[EGA/VGA]: (Enhanced Graphics Adapter/Video Graphics Array) For EGA, VGA, SVGA and PGA
monitor adapters.
[CGA 40]: (Color Graphics Adapter) Power up in 40-column mode.
[CGA 80]: (Color Graphics Adapter) Power up in 80-column mode.
[Mono]: (Monochrome adapter) Includes high-resolution monochrome adapters.
Halt On:
This item determines whether the system stops if an error is detected during system boot-up.
[All Errors]: The system-boot will stop whenever the BIOS detect a non-fatal error.
[No Errors]: The system-boot will not stop for any error detected.
[All, But Keyboard]: The system-boot will stop for all errors except a keyboard error.
[All, But Diskette]: The system-boot will stop for all errors except a diskette error.
[All, But Disk/Key]: The system-boot will stop for all errors except a diskette or keyboard error.
Base Memory:
This item displays the amount of base memory installed in the system. The value of the base memory is
typically 640K for system with 640K or more memory size installed on the motherboard.
Extended Memory:
This item displays the amount of extended memory detected during system boot-up.
Total Memory:
This item displays the total memory available in the system.
IS7-V
BIOS Setup
3-7
3-3. Advanced BIOS Features
Hyper-Threading Technology
This option enables or disables the processor’s Hyper-Threading Technology
Leave this item to its default setting to enable the simultaneous multi-threaded (SMT) processor so as to
make one physical processor looks like two logical processors to the OS and applications.
This option is for CPU with Hyper-Threading Technology only. For more information on
“Hyper-Threading Technology”, please visit Intel Web site at
http://www.intel.com/homepage/land/hyperthreading.htm , http://www.intel.com/design/chipsets/ht/.
Quick Power On Self Test:
When set to [Enabled], this item speeds up the Power On Self Test (POST) after powering on the system.
The BIOS shorten or skip some check during the POST.
Hard Disk Boot Priority:
This item selects the hard disks booting priority. By pressing <Enter> key, you can enter its submenu
where the hard disks detected can be selected for the booting sequence to boot up system.
This item functions only when there is the option of [Hard Disk] in any one of the First/Second/Third
Boot Device items.
HDD Change Message:
When set to [Enabled], a pop-up message will be displayed on the screen during the POST process if the
hard drives installed in your system had been changed.
First Boot Device / Second Boot Device / Third Boot Device / Boot Other Device:
Select the drive to boot first, second and third in the [First Boot Device], [Second Boot Device], and
[Third Boot Device] items respectively. The BIOS will boot the operating system according to the
sequence of the drive selected. Set [Boot Other Device] to [Enabled] if you wish to boot from another
device other than these three items.
Swap Floppy Drive:
When set to [Enabled], and the system is booting from the floppy drive, the system will boot from drive B
User’s Manual
3-8
Chapter 3
instead of the regular drive A. There must be two floppy drives connected in the system to use this
function.
Boot Up Floppy Seek:
When set to [Enabled], the BIOS will check whether the floppy disk drive is installed or not.
Boot Up NumLock Status:
This item determines the default state of the numeric keypad at system booting up.
[On]: The numeric keypad functions as number keys.
[Off]: The numeric keypad functions as arrow keys.
Security Option:
This item determines when the system will prompt for password - every time the system boots or only
when enters the BIOS setup.
[Setup]: The password is required only when accessing the BIOS Setup.
[System]: The password is required each time the computer boots up.
NOTE: Don’t forget your password. If you forget the password, you will have to open the computer case
and clear all information in the CMOS before you can start up the system. But by doing this, you will
have to reset all previously set options.
APIC Mode:
Leave this item to its default setting.
MPS Version Ctrl For OS:
This item specifies which version of MPS (Multi-Processor Specification) this motherboard will use.
Leave this item to its default setting.
OS Select For DRAM > 64MB:
This item allows you to access the memory that is over 64MB in OS/2. Leave this item to its default
[Non-OS2] setting for operating system other than OS/2.
Report No FDD For OS:
When set to [Yes], this item allows you to run some older operating system without floppy disk drive.
Leave this item to its default setting.
Delay IDE Initial (Secs):
This item allows the BIOS to support some old or special IDE devices by prolonging this delay time. A
larger value will give more delay time to the device for which to initialize and to prepare for activation.
Intel OnScreen Branding:
This item determines whether to display the “Intel Inside” logo or not at system boots up.
Disable Unused PCI Clock:
This option disables the clock of PCI slot that is not in use.
IS7-V
BIOS Setup
3-9
[Yes]: The system automatically detect the unused DIMM and PCI slots, and stop sending clock signal to
these unused PCI slots.
[No]: The system always send clock signal to all PCI slots.
NOTE: Set this option to [No] setting if there are adapters that cannot be automatically detected by the
system and will cause malfunction.
User’s Manual
3-10
Chapter 3
3-4. Advanced Chipset Features
DRAM Timing Selectable:
This item sets the optimal timings for the following four items, depending on the memory module you are
using. The default setting “By SPD” configures these four items by reading the contents in the SPD
(Serial Presence Detect) device. The EEPROM on the memory module stores critical parameter
information about the module, such as memory type, size, speed, voltage interface, and module banks.
CAS Latency Time:
This item controls the latency between the DRAM read command and the time that the data becomes
actually available.
Act to Precharge Delay:
This item controls the number of DRAM clocks used for the DRAM parameters.
DRAM RAS# to CAS# Delay
This item controls the latency between the DRAM active command and the read/write command.
DRAM RAS# Precharge:
This item controls the idle clocks after issuing a precharge command to the DRAM.
System BIOS Cacheable:
When set to [Enabled], accesses to the system BIOS ROM addressed at F0000H-FFFFFH are cached,
provided that the cache controller is enabled. The larger the range of the Cache RAM, the higher the
efficiency of the system will be.
Video BIOS Cacheable:
As with caching the system BIOS, enabling the Video BIOS cache will allow access to video BIOS
addressed at C0000H to C7FFFH to be cached, if the cache controller is also enabled. The larger the
range of the Cache RAM, the faster the video performance will be.
IS7-V
BIOS Setup
3-11
Memory Hole At 15M-16M:
When set to [Enabled], the memory address space at 15M-16M will be reserved for ISA expansion cards
that specifically requires this setting. This makes the memory from 15MB and up unavailable to the
system. Leave this item to its default setting.
Delay Prior to Thermal:
This item selects the delay time before thermal activation.
AGP Aperture Size:
This option specifies the amount of system memory that can be used by the AGP device. The aperture is a
portion of the PCI memory address range dedicated for graphics memory address space.
Init Display First:
This item selects to initialize AGP or PCI Slot first when the system boots.
[AGP]: When the system boots, it will first initialize AGP.
[PCI Slot]: When the system boots, it will first initialize PCI.
AGP Data Rate Capability:
This item selects the data transfer rate of AGP device. A higher rate delivers faster and better graphics to
your system. Make sure your graphics card supports the mode you select.
User’s Manual
3-12
Chapter 3
3-5. Integrated Peripherals
OnChip IDE Device:
Click <Enter> key to enter its submenu:
IDE Bus Master:
This option enables or disables the IDE bus mastering capability under the DOS environment.
OnChip IDE-1 Controller:
This item allows you to enable or disable the primary and secondary IDE controller. Select [Disabled] if
you want to add a different hard drive controller.
Master/Slave Drive PIO Mode
The PIO (Programmed Input/Output) mode allows the BIOS to tell the controller what it wants and then
let the controller and the CPU perform the complete task, rather than having the BIOS issue a series of
commands to affect a transfer to or from the disk drive.
[Auto]: The BIOS will select the best available mode after checking your disk drive.
[Mode 0-4]: You can select a mode that matches your disk drive’s timing. Do not use the wrong setting
or you will have drive errors.
Master/Slave Drive Ultra DMA
This item allows you to set the Ultra DMA in use.
[Auto]: The BIOS will select the best available option after checking your hard drive or CD-ROM.
[Disabled]: The BIOS will not detect these categories. If problem arises in using Ultra DMA devices, try
disabling this item.
IS7-V
BIOS Setup
3-13
OnChip IDE-2 Controller:
The description is same as the OnChip IDE-1 Controller.
OnChip Serial ATA:
This item determines the function for on-chip Serial ATA.
[Disabled]: Disable the Serial ATA controller.
[Auto]: Allows the Serial ATA controller to be arranged by BIOS automatically.
[Combined Mode]: Parallel ATA and Serial ATA are combined together. Supports up to 2 IDE drives in
each channel.
[Enhanced Mode]: Enable both Parallel ATA and Serial ATA. Supports up to 6 IDE drives.
[SATA Only]: The SATA is operating in legacy mode.
Serial ATA 1 Mode / Serial ATA 2 Mode:
This item determines the function mode for Serial ATA Port 1 (i.e. The SATA1 connector in this model)
and Serial ATA Port 2 (i.e. The SATA2 connector in this model). Both SATA1 and SATA2 will be
served each as one single IDE connector after selected as the following modes:
Mode
Serial ATA Port 1
(SATA1)
IDE-3 Master
Enhanced
IDE-4 Master
IDE-1 Master
IDE-1 Slave
Combined
IDE-2 Master
IDE-2 Slave
IDE-1 Master
SATA Only
IDE-2 Master
Serial ATA Port 2
Description
(SATA2)
• SATA1 serves as IDE-3 Master
• SATA2 serves as IDE-4 Master
IDE-4 Master
• OnChip IDE-1 and IDE-2 controller
enabled
• SATA1 serves as IDE-4 Master
• SATA2 serves as IDE-3 Master
IDE-3 Master
• OnChip IDE-1 and IDE-2 controller
enabled
• SATA1 serves as IDE-1 Master
IDE-1 Slave
• SATA2 serves as IDE-1 Slave
• OnChip IDE-1 controller disabled
• SATA1 serves as IDE-1 Slave
IDE-1 Master
• SATA2 serves as IDE-1 Master
• OnChip IDE-1 controller disabled
• SATA1 serves as IDE-2 Master
IDE-2 Slave
• SATA2 serves as IDE-2 Slave
• OnChip IDE-2 controller disabled
• SATA1 serves as IDE-2 Slave
IDE-2 Master
• SATA2 serves as IDE-2 Master
• OnChip IDE-2 controller disabled
• SATA1 serves as IDE-1 Master
• SATA2 serves as IDE-2 Master
IDE-2 Master
• OnChip IDE-1 and IDE-2 controller
disabled
• SATA1 serves as IDE-2 Master
• SATA2 serves as IDE-1 Master
IDE-1 Master
• OnChip IDE-1 and IDE-2 controller
disabled
User’s Manual
3-14
Chapter 3
OnChip PCI Device:
Click <Enter> key to enter its submenu:
OnChip USB Controller:
This option enables or disables the USB controller.
USB 2.0 Controller:
This option enables or disables the USB 2.0 controller.
USB Keyboard Support Via:
This item allows you to select [BIOS] for using USB keyboard in DOS environment, or [OS] in OS
environment.
USB Mouse Support Via:
This item allows you to select [BIOS] for using USB mouse in DOS environment, or [OS] in OS
environment.
OnChip Audio Controller:
This option enables or disables the audio controller.
SuperIO Device:
Click <Enter> key to enter its submenu:
IS7-V
BIOS Setup
3-15
Onboard FDC Controller:
This option enables or disables the onboard FDC controller.
Onboard Serial Port:
This item determines which I/O addresses the onboard Serial Port controller will access.
[Auto]: The system automatically select an I/O address for the onboard Serial Port.
[3F8/IRQ4, 2F8/IRQ3, 3E8/IRQ4, 2E8/IRQ3]: Allows you to manually select an I/O address for the
onboard Serial Port.
[Disabled]: Disables the onboard Serial Port.
Onboard Parallel Port:
This item specifies the I/O address used by the parallel port.
[Disabled]: This option prevents the parallel port from accessing any system resources. When the value
of this option is set to [Disabled], the printer port becomes unavailable.
[378/IRQ7]: This option allows the parallel port to use [378/IRQ7] as its I/O port address. The majority
of parallel ports on computer systems use IRQ7 and I/O Port 378H as the standard setting.
[278/IRQ5]: This option allows the parallel port to use [278/IRQ5] as its I/O port address.
[3BC/IRQ7]: This option allows the parallel port to use [3BC/IRQ7] as its I/O port address.
Parallel Port Mode:
This item specifies the parallel port mode.
[Normal]: Allows the standard parallel port mode to be used.
[SPP]: (Standard Parallel Port) Allows bi-directional parallel port operation at normal speed.
[EPP]: (Enhanced Parallel Port) Allows bi-directional parallel port operation at maximum speed.
[ECP]: (Extended Capabilities Port) Allows bi-directional parallel port operation at a speed faster than
the normal mode’s data transfer rate.
[ECP+EPP]: Allows parallel port operation at ECP and EPP mode.
EPP Mode Select:
This item selects the EPP mode.
ECP Mode Use DMA:
This item selects the DMA channel of the parallel port.
User’s Manual
3-16
Chapter 3
Onboard PCI Device:
Click <Enter> key to enter its submenu:
Onboard LAN Controller:
This option enables or disables the LAN controller.
LAN Boot ROM:
This item allows you to use the boot ROM (instead of a disk drive) to boot-up the system and access the
local area network directly.
Enhance Performance:
This option enhances the LAN performance by making it as the first priority among the PCI devices.
IS7-V
BIOS Setup
3-17
3-6. Power Management Setup
ACPI Suspend Type:
This item selects the type of Suspend mode.
[S1(Power On Suspend)]: Enables the Power On Suspend function.
[S3(Suspend To RAM)]: Enables the Suspend to RAM function.
Resume by USB From S3:
When set to [Enabled], this item allows you to use a USB device to wake up a system that is in the S3
(STR - Suspend To RAM) state. This item can be configured only if the item “ACPI Suspend Type” is set
to [S3(STR)].
Power Button Function:
This item selects the method of powering off your system:
[Delay 4 Sec.]: Pushing the power button for more than 4 seconds will power off the system. This will
prevent the system from powering off in case you accidentally hit or pushed the power button.
[Instant-Off]: Pressing and then releasing the power button at once will immediately power off the
system.
CPU THRM-Throttling
This item controls the CPU speed by cutting down its regular power to a percentage during the STR
(Suspend To RAM) state.
WakeUp by PME# of PCI:
When set to [Enabled], access to the onboard LAN or a PCI card such as a modem or LAN card will
cause the system to wake up. The PCI card must support the wake up function.
WakeUp by OnChip Lan:
When set to [Enabled], you can remotely wake up a PC in Soft-Off condition via a LAN card that support
the wake up function.
WakeUp by Alarm:
When set to [Enabled], you can set the date and time you would like the Soft-Off PC to power-on in the
“Date (of Month) Alarm” and “Time (hh:mm:ss) Alarm” items. However, if the system is being
accessed by incoming calls or the network (Resume On Ring/LAN) prior to the date and time set in these
items, the system will give priority to the incoming calls or network instead.
User’s Manual
3-18
Chapter 3
Date (of Month) Alarm
[0]: This option power-on the system everyday according to the time set in the “Time (hh:mm:ss) Alarm”
item.
[1-31]: This option selects a date you would like the system to power-on. The system will power-on on
the date set, and the time set in the “Time (hh:mm:ss) Alarm” item.
Time (hh:mm:ss) Alarm
This item sets the time you would like the system to power-on.
POWER ON Function:
This item selects the way you want your system to power on.
[Password]: Use a password to power on the system, select this option then press <Enter>. Enter your
password. You can enter up to 5 characters. Type in exactly the same password to confirm, and then press
<Enter>.
[Hot KEY]: Use any of the function keys between <F1> to <F12> to power on the system.
[Mouse Left]: Double click the mouse left button to power on the system.
[Mouse Right]: Double click the mouse right button to power on the system.
[Any KEY]: Use any keyboard keys to power on the system.
[BUTTON ONLY]: Use only the power button to power on the system.
[Keyboard 98]: Use the power-on button on the “Keyboard 98” compatible keyboard to power on the
system.
NOTE: The mouse wake up function can only be used with the PS/2 mouse, not with the COM port or
USB type. Some PS/2 mice cannot wake up the system because of compatible problems. If the specs of
your keyboard are too old, it may fail to power on.
KB Power ON Password:
This item sets the password required in order to power on your computer.
NOTE: Do not forget your password, or you will have to clear the CMOS and reset all parameters in
order to utilize this function again.
Hot Key Power ON:
This item powers on the system by pressing <Ctrl> key plus one of each function key (<F1> ~ <F12>)
simultaneously.
Restore On AC Power Loss:
This item selects the system action after an AC power failure.
[Power Off]: When power returns after an AC power failure, the system’s power remains off. You must
press the Power button to power-on the system.
[Power On]: When power returns after an AC power failure, the system’s power will be powered on
automatically.
[Last State]: When power returns after an AC power failure, the system will return to the state where you
left off before power failure occurs. If the system’s power is off when AC power failure occurs, it will
remain off when power returns. If the system’s power is on when AC power failure occurs, the system
will power-on when power returns.
IS7-V
BIOS Setup
3-19
3-7. PnP/PCI Configurations
Resources Controlled By:
This item configures all of the boot and Plug-and-Play compatible devices.
[Auto]: The system will automatically detect the settings.
[Manual]: Choose the specific IRQ resources in the “IRQ Resources” menu.
IRQ Resources:
Click <Enter> key to enter its submenu:
This item sets each system interrupt to either [PCI Device] or [Reserved].
PCI/VGA Palette Snoop:
This item determines whether the MPEG ISA/VESA VGA cards can work with PCI/VGA or not.
[Enabled]: MPEG ISA/VESA VGA cards work with PCI/VGA.
[Disabled]: MPEG ISA/VESA VGA cards do not work with PCI/VGA.
Allocate IRQ To Video:
This item assigns an IRQ for the VGA card installed.
[Enabled]: Automatically assign an IRQ for the VGA card installed.
User’s Manual
3-20
Chapter 3
[Disabled]: The IRQ that was previously occupied by the VGA card will be available for new device.
Allocate IRQ To USB:
This item assigns an IRQ for the USB device connected.
[Enabled]: Automatically assign an IRQ for the USB device connected.
[Disabled]: The IRQ that was previously occupied by the USB device connected will be available for
new device.
PCI Latency Timer(CLK):
This item controls how long each PCI device can hold the bus before another takes over. When set to
higher values, every PCI device can conduct transactions for a longer time and thus improve the effective
PCI bandwidth. For better PCI performance, you should set the item to higher values.
PIRQ_0 Use IRQ No. ~ PIRQ_7 Use IRQ No.:
This item specifies the IRQ number manually or automatically for the devices installed on PCI slots.
For the relations between the hardware layout of PIRQ (the signals from the ICH chipset), INT# (means
PCI slot IRQ signals) and devices, please refer to the table below:
PCI-1
PCI-2
PCI-3
PIRQ_4 Assignment
INT A
PIRQ_5 Assignment
INT B
PIRQ_6 Assignment
PIRQ_7 Assignment
AGP
PIRQ_0 Assignment
INT A
INT D
PIRQ_1 Assignment
INT B
INT A
PIRQ_2 Assignment
PIRQ_3 Assignment
IS7-V
LAN
Signals
INT A
PCI-4
PCI-5
INT D
INT C
INT B
INT A
INT D
INT C
INT C
INT B
INT A
INT D
INT D
INT C
INT B
INT A
INT B
INT C
BIOS Setup
3-21
3-8. PC Health Status
FAN Fail Alarm Selectable:
This item selects the fan that will be monitored for malfunction.
Shutdown When CPUFAN Fail:
When set to [Enabled], the system will be shut down if the CPU fan is not running.
Shutdown Temperature:
This item sets the temperature that would shutdown the system automatically in order to prevent system
overheats.
CPU Warning Temperature:
This item selects the CPU’s warning temperature limit. Once the system has detected that the CPU’s
temperature exceeded the limit, warning beeps will sound.
NOTE: The onboard hardware monitor function is capable of detecting these system health conditions. If
you want a warning message to pop-up or a warning alarm to sound when an abnormal condition occurs,
you must install the “Hardware Doctor” utility. This utility is included in the “Driver & Utility CD” that
came packed with this motherboard.
All Voltages, Fans Speed and Thermal Monitoring:
These unchangeable items list the current status of the CPU and environment temperatures, fan speeds,
and system power voltage.
NOTE: The hardware monitoring features for temperatures, fans and voltages will occupy the I/O
address from 294H to 297H. If you have a network adapter, sound card or other add-on cards that might
use those I/O addresses, please adjust your add-on card I/O address to avoid using these addresses.
User’s Manual
3-22
Chapter 3
3-9. Load Fail-Safe Defaults
This option loads the BIOS default values for the most stable, minimal-performance system operations.
3-10. Load Optimized Defaults
This option loads the BIOS default values that are factory settings for optimal-performance system
operations.
3-11. Set Password
This option protects the BIOS configuration or restricts access to the computer itself.
3-12. Save & Exit Setup
This option saves your selections and exits the BIOS setup menu.
3-13. Exit Without Saving
This option exits the BIOS setup menu without saving any change.
IS7-V
Install Intel Chipset Software Utility
A-1
Appendix A. Install Intel Chipset Software Utility
NOTE: Please install this Intel Chipset driver first after having installed the Windows operating system.
The installation procedures and screen shots in
this section are based on Windows XP operating
system. For those of other OS, please follow its
on-screen instruction.
Insert the Driver & Utility CD into CD-ROM
drive, it should execute the installation program
automatically. If not, double-click the execution
file at the main directory of this CD to enter the
installation menu.
After entering the installation menu, move your
curser to [Drivers] tab. Click [Intel Chipset
Software Utility]. The following screen appears.
1.
Click [Next].
2.
Click [Yes].
3.
Click [Next].
4. Choose [Yes, I want to restart my computer
now.], and click [Finish] to complete setup.
User’s Manual
A-2
IS7-V
Appendix A
Install Audio Driver
B-1
Appendix B. Install Audio Driver
The installation procedures and screen shots in
this section are based on Windows XP operating
system. For those of other OS, please follow its
on-screen instruction.
Insert the Driver & Utility CD into CD-ROM
drive, it should execute the installation program
automatically. If not, double-click the execution
file at the main directory of this CD to enter the
installation menu.
After entering the installation menu, move your
curser to [Drivers] tab. Click [Audio Driver].
The following screen appears.
1.
Click [Next].
3. After the system restarted, a shortcut icon
appears at the right corner of Windows task bar.
4. In this Speaker Configuration tab, select [6
channels mode for 5.1 speakers output] to
enable 6-channel audio system.
2. Choose [Yes, I want to restart my computer
now.], and click [Finish] to complete setup.
User’s Manual
B-2
IS7-V
Appendix B
Install LAN Driver
C-1
Appendix C. Install LAN Driver
The installation procedures and screen shots in
this section are based on Windows XP operating
system. For those of other OS, please follow its
on-screen instruction.
Insert the Driver & Utility CD into CD-ROM
drive, it should execute the installation program
automatically. If not, double-click the execution
file at the main directory of this CD to enter the
installation menu.
After entering the installation menu, move your
curser to [Drivers] tab. Click [LAN Driver]. The
following screen appears.
1.
Click [Next].
2.
Click [Finish] to complete setup.
User’s Manual
C-2
IS7-V
Appendix C
Install USB 2.0 Driver
D-1
Appendix D. Install USB 2.0 Driver
NOTE: The “USB 2.0 Driver” packed in the “Driver & Utility CD” is currently available for Windows
9x and ME only. To install this driver for Windows XP or Windows 2000, you have to download their
latest service pack first from Microsoft’s web site.
To install the USB 2.0 driver for Windows 9x and ME, please insert the Driver & Utility CD into
CD-ROM drive. It should execute the installation program automatically. If not, double-click the
execution file at the main directory of this CD to enter the installation menu. The following screen
appears.
Click [USB 2.0 Driver], and then follow the on-screen instruction to complete the driver installation.
User’s Manual
D-2
IS7-V
Appendix D
BIOS Update Guide
E-1
Appendix E. BIOS Update Guide
The procedure illustrated here is based on the model SE6 as an example; all other models follow the same
process.
1.
First, find out the model name and version number of this motherboard. You can find a bar-code
sticker typed with model name and version number on motherboard PCB.
2.
Find out the current BIOS ID. For example, in this case, the current BIOS ID is [00]. If you already
have the latest BIOS, no any update action is necessary. If your BIOS is not the latest BIOS, go on to
the next step.
3.
Download the correct BIOS file from our Web site.
4.
Double click the downloaded file, it will self-extract
to [awdflash.exe] and [*.bin] files.
5.
Make a bootable floppy disk and copy the necessary
files onto it. You may make a floppy disk bootable
either in Explorer or in the DOS prompt mode.
[c:\]format a: /s
After formatting and transferring the system to the
floppy disk, copy two files into it. One is the BIOS
flash utility [awdflash.exe] and the other is the
decompressed BIOS binary [*.bin] file.
User’s Manual
E-2
Appendix E
6.
Please set the first boot sequence as “Floppy” in BIOS and boot off the floppy disk.
7.
Flash the BIOS in pure DOS mode.
A:\>awdflash se6_sw.bin /cc /cd /cp /py /sn /cks /r_
Note
•
We strongly recommend you use the above parameters following ‘awdflash’ to flash your BIOS.
DO NOT just type “awdflash se6_sw.bin” without the above parameters following the “.bin”
file.
•
The Award flash utility cannot be completed under the Windows environment. It must be done in
a pure DOS environment.
•
You should check which BIOS file is to be used with your motherboard, don’ flash with the
wrong BIOS file. Otherwise, it may cause system malfunctions.
•
Please do not use the Award flash memory writer version earlier than Version 7.52C to flash the
BIOS. Otherwise, it may cause flash fail or un-anticipated problems.
•
During the updating, the progress will be measured by white blocks. The last four blue blocks of
the flash update process represent the “BIOS boot block”. The BIOS boot block is used to prevent
the BIOS from becoming corrupt during programming. It should not be programmed every time.
If this “BIOS boot block” remains intact when the BIOS becomes corrupt during programming,
then you can boot from a bootable floppy next time you boot your computer. This allows you to
flash your BIOS again without the need for technical support from the dealer.
IS7-V
Hardware Monitoring (The Winbond Hardware Doctor Utility)
F-1
Appendix F. Hardware Monitoring (The Winbond
Hardware Doctor Utility)
The Winbond Hardware Doctor is a self-diagnostic system for PCs used with Winbond W83627HF
chipset. It protects PC hardware by monitoring several critical items including power supply voltages,
CPU & system fan speeds and CPU and system temperatures. These items are important for the system
operation. Errors may result in permanent damage to the PC. Once any item is out of its normal range, a
warning message pops up reminding you to take proper measures.
The installation procedures and screen shots in
this section are based on Windows XP operating
system. For those of other OS, please follow its
on-screen instruction.
Insert the Driver & Utility CD into CD-ROM
drive, it should execute the installation program
automatically. If not, double-click the execution
file at the main directory of this CD to enter the
installation menu.
After entering the installation menu, move your
curser to [Hardware Doctor] tab. Click [Install
Hardware Doctor]. The following screen
appears.
1.
Click [Next].
2.
Click [Next].
3.
Click [Next].
4.
Click [Next].
User’s Manual
F-2
Appendix F
critical or over its limitation, the reading turns
red. Also, a pop-up window appears warning
you the system has a problem!
5. Choose [Yes, I want to restart my computer
now.] and click [Finish] to complete setup.
8.
This is the warning message window:
Ignore: You can ignore the warning message of
the item, but it will pop up again when an error
of the same item reoccurs.
Disable: The chosen item will be no longer
monitored thereafter, unless you activate it in
the “Configuration” page.
Shutdown: Choosing this button will shutdown
the computer.
6. Execute the Hardware Doctor by entering
the Windows Menu [Start] [Programs] [Winbond] [Hardware Doctor].
Help: You can read more information and
self-diagnose simple problems.
If the warning message pops up due to the
wrong warning limit, you can adjust it in the
“Configuration” option. For example, if you
set the temperature high limit to 40°C, you will
easily exceed the “proper” temperature.
Pay attention to two things when you want to
make any change to the “Configuration” option.
Firstly, you have to make sure your new setting
is in the proper range. Secondly, after you
finished the configuration, you have to save it.
Otherwise, the program will start with the
default value next time.
If you encounter any problem or have any
question about the software settings and
adjustments, please use the Winbond hardware
doctor on-line help. It should give you enough
information to answer your questions.
7. This screen appears. Hardware Doctor
shows you the status of Voltage, Fan Speed, and
Temperature readings as well. If any reading is
IS7-V
Troubleshooting (Need Assistance?)
G-1
Appendix G. Troubleshooting (Need Assistance?)
Q & A:
Q: Do I need to clear the CMOS before I use a new motherboard to assemble my new computer
system?
A: Yes, we highly recommend that you clear the CMOS before installing a new motherboard. Please
move the CMOS jumper from its default 1-2 position to 2-3 for a few seconds, and then back. When
you boot up your system for the first time, follow the instructions in the user's manual to load the
optimized defaults.
Q: If my systems hang when I update the BIOS or set the wrong CPU parameters, what should I
do?
A: Whenever you update the BIOS or if the system hangs due to wrong CPU parameters setting, always
clear CMOS jumper before booting up again.
Q: Why the system failed to boot up and nothing was displayed on the screen after I did some
over-clocking or non-standard settings inside the BIOS? Is the motherboard dead? Do I need to
return it to where I bought from or go through an RMA process?
A: It should not cause hardware or permanent damage to motherboard when BIOS settings were
changed from default to over-clocking or non-standard status.
We suggest the following three troubleshooting methods to discharge CMOS data, recover the
hardware default status, and then make the motherboard working again. No need to bother returning
the motherboard to where you bought from or go through an RMA process.
Step 1. Switch off the power supply unit and then switch it on again after one minute. If there is no
power switch on the power supply unit, disconnect its power cord for one minute and then
connect it back.
Press and hold the <Insert> key on the keyboard, press the power-on button to boot up
system. If it works, loose the <Insert> key and hit <Del> key to enter the BIOS setup page to
do the correct settings.
If the situation remains the same, repeat the procedures in Step 1 for three times, or try Step
2.
Step 2. Switch off the power supply unit or disconnect the power cord. Open the chassis cover.
Locate the CCMOS jumper near the button battery. Change the jumper position from default
1-2 to 2-3 for one minute to discharge the CMOS data, and then put it back to default 1-2
position.
Close the chassis and switch on the power supply unit or plug in the power cord. Press the
power-on button to boot up system. If it works, hit <Del> key to enter the BIOS setup page
to do the correct settings.
If the situation remains the same, try Step 3.
Step 3. The same procedure as Step 2, but in the meantime of discharging the CMOS data, pull out
ATX power connectors from motherboard and remove the button battery during CMOS
discharging.
User’s Manual
G-2
Appendix G
Q: How can I get a quick response to my request for technical support?
A: Be sure to follow the guidelines as stated in the “Technical Support Form” section of this manual.
If you have a problem during operation, in order to help our technical support personnel quickly
determine the problem with your motherboard and give you the answers you need, before filling in
the technical support form, eliminate any peripheral that is not related to the problem, and indicate it
on the form. Fax this form to your dealer or to the company where you bought the hardware in order
to benefit from our technical support. (You can refer to the examples given below)
Example 1:
With a system including: motherboard (with CPU, DRAM, COAST...) HDD, CD-ROM, FDD, VGA
CARD, MPEG CARD, SCSI CARD, SOUND CARD, etc. After the system is assembled, if you
cannot boot up, check the key components of the system using the procedure described below. First
remove all interface cards except the VGA card and try to reboot.
If you still cannot boot up: Try installing another brand/model VGA card and see if the system will
start. If it still does not start, note the VGA card model, motherboard model, Bios identification
number, CPU on the technical support form (refer to main instructions), and describe the problem in
the problem description space provided.
If you can boot up: Insert the interface cards you have removed back into the system, one by one
and try to start the system each time you insert a card, until the system will not start. Keep the VGA
card and the interface card that caused the problem inserted on the motherboard, remove any other
cards or peripheral, and start again. If you still cannot start, note the information related to both cards
in the add-on Card space provided, and don’t forget to indicate the motherboard model, version,
BIOS identification number, CPU (refer to main instructions), and give a description of the problem.
Example 2:
With a system including the motherboard (with CPU, DRAM, COAST...) HDD, CD-ROM, FDD,
VGA CARD, LAN CARD, MPEG CARD, SCSI CARD, SOUND CARD, after assembly and after
having installed the Sound Card Driver, when you restart the system, when it runs the Sound Card
Driver, it resets automatically. This problem may be due to the Sound Card Driver. During the
Starting DOS… procedure, press SHIFT (BY-PASS) key, to skip CONFIG.SYS and
AUTOEXEC.BAT; edit CONFIG.SYS with a text editor, and in function the line that loads the
Sound Card Driver, add a remark REM, in order to disable the Sound Card Driver. See the example
below.
CONFIG.SYS:
DEVICE=C:\DOS\HIMEM.SYS
DEVICE=C:\DOS\EMM386.EXE HIGHSCAN
DOS=HIGH, UMB
FILES=40
BUFFERS=36
REM DEVICEHIGH=C:\PLUGPLAY\DWCFGMG.SYS
LASTDRIVE=Z
Restart the system. If the system starts and does not reset, you can be sure that the problem is due to
the Sound Card Driver. Write down the Sound Card model, motherboard model, BIOS identification
number on the technical support file (refer to main instructions), and describe the problem in the
space provided.
We will show you how to fill the “Technical Support Form”.
IS7-V
Troubleshooting (Need Assistance?)
G-3
Main instructions:
To fill in this “Technical Support Form”, refer to the step-by-step instructions given below:
1*. MODEL: Note the model number given in your user’s manual.
Example: IS7-V
*
2 . Motherboard model number (REV): Note the motherboard model number labeled on the
motherboard as “REV:*.**”.
Example: REV: 1.01
*
3 . BIOS ID and Part Number: See the on screen message.
4.
DRIVER REV: Note the driver
version number indicated on the
DEVICE DRIVER disk (if any) as
“Release *.**”. For example:
5*. OS/APPLICATION: Indicate the
operating system and applications
you are running on the system.
Example: MS-DOS® 6.22,
Windows® 98 SE, Windows® 2000, etc....
6*. CPU: Indicate the brand and the speed (MHz) of your CPU.
Example:(A) In the “Brand” space, write “Intel”; in the “Specifications” space, write “Pentium® 4
1.9GHz”.
7.
HDD: Indicate the brand and specifications of your HDD(s); specify if the HDD is using IDE1 or
IDE2. If you know the disk capacity, indicate it and check (“”) “ ”; in case you give no
indication, we will consider that your HDD is “IDE1” Master.
Example: In the “HDD” space, check the box; in the Brand space, write “Seagate”; in the
Specifications space, write “ST31621A (1.6GB)”.
8.
CD-ROM Drive: Indicate the brand and specifications of your CD-ROM drive. Specify if it uses IDE1 or IDE2, and check (“”) “ ”; in case you give no indication, we will consider that your
CD-ROM is “IDE2” Master.
Example: In the “CD-ROM drive” space, check the box, in the Brand space, write “Mitsumi”, in the
Specifications space, write “FX-400D”.
9.
System Memory (DDR SDRAM): Indicate the brand and specifications (DDR DIMM) of your
system memory. Such as Density, Description, Module Components, Module Part Number, CAS
Latency, and Speed (MHz).
For example: In the Brand space, write “Micron”; in the Specifications space, write: Density:
128MB, Description: SS 16 Megx72 2.5V ECC Gold, Module Components: (9) 16 Megx 8,
Module Part Number: MT9VDDT1672AG, CAS Latency: 2, Speed (MHz): 200 MHz.
Please give us the detailed information of your DDR SDRAM module; it will help us to simulate the
problems you met.
10. ADD-ON CARD: Indicate which add-on cards you are absolutely sure are related to the problem.
If you cannot identify the problem’s origin, indicate all the add-on cards inserted into your system.
NOTE: Items between the “*” are absolutely necessary.
User’s Manual
G-4
Appendix G
Technical Support Form
Company Name:
Phone Number:
Contact Person:
Fax Number:
E-mail Address:
Model
*
Motherboard Model No.
DRIVER REV
OS/Application
*
Hardware Name
Brand
CPU
HDD
CD-ROM-Drive
System Memory
ADD-ON CARD
Problem Description:
IS7-V
*
IDE1
IDE2
IDE1
IDE2
BIOS ID #
Specifications
*
How to Get Technical Support
H-1
Appendix H. How to Get Technical Support
(From our website) http://www.abit.com.tw
(In North America) http://www.abit-usa.com
(In Europe) http://www.abit.nl
Thank you for choosing ABIT products. ABIT sells all our products through distributors,
resellers and system integrators; we have no direct sales to end-users. Before sending email
for tech support please check with your resellers or integrators if you need any services, they
are the ones who sold you your system and they should know best as to what can be done,
how they serve you is a good reference for future purchases.
We appreciate every customer and would like to provide the best service to you. Providing
fast service to our customers is our top priority. However we receive many phone calls and a
huge amount of email from all over the world. At the present time it is impossible for us to
respond to every single inquiry. Therefore it is quite possible that if you send an email to us
that you may not receive a response.
We have done many compatibility tests and reliability tests to make sure our products have
the best quality and compatibility. In case you need service or technical support, please
understand the constraint we have and always check with the reseller who sold the product
to you first.
To expedite service, we recommend that you follow the procedures outlined below before
contacting us. With your help, we can meet our commitment to provide the best service to the
greatest number of ABIT customers:
1. Check the Manual. It sounds simple but we have taken a lot of care in making a
well-written and thorough manual. It is full of information that doesn't only pertain to
motherboards. The CD-ROM included with your board will have the manual as well as
drivers. If you don't have either one, go to our Program Download Area of the Website or
FTP server.
2. Download latest BIOS, software or drivers. Please go to our Program Download area
on our Website to check to see if you have the latest BIOS. They are developed over
periods of time to fixes bugs or incompatibilities. Also please make sure you have the
latest drivers from your peripheral cards makers!
3. Check the ABIT Technical Terms Guide and FAQ on our Website. We are trying to
expand and make the FAQs more helpful and information rich. Let us know if you have
any suggestions. For hot topics check out our HOT FAQ!
User’s Manual
H-2
Appendix H
4. Internet Newsgroups. They are a great source of information and many people there can
offer help. ABIT's Internet News group, alt.comp.periphs.mainboard.abit, is an ideal
forum for the public to exchange information and discuss experiences they have had with
ABIT products. Many times you will see that your question has already been asked before.
This is a public Internet news group and it is reserved for free discussions. Here is a list of
some of the more popular ones:
alt.comp.periphs.mainboard.abit
comp.sys.ibm.pc.hardware.chips
alt.comp.hardware.overclocking
alt.comp.hardware.homebuilt
alt.comp.hardware.pc-homebuilt
5. Ask your reseller. Your ABIT authorized distributor should be able to provide the fastest
solution to your technical problem. We sell our products through distributors who sell to
resellers and stores. Your reseller should be very familiar with your system configuration
and should be able to solve your problem much more efficiently than we could. After all,
your reseller regards you as an important customer who may purchase more products and
who can urge your friends to buy from him or her as well. They integrated and sold the
system to you. They should know best what your system configuration is and your
problem. They should have reasonable return or refund policies. How they serve you is
also a good reference for your next purchase.
6. Contacting ABIT. If you feel that you need to contact ABIT directly you can send email
to the ABIT technical support department. First, please contact the support team for the
branch office closest to you. They will be more familiar with local conditions and
problems and will have better insight as to which resellers offer what products and
services. Due to the huge number of emails coming in every day and other reasons, such
as the time required for problem reproduction, we will not be able to reply to every email.
Please understand that we are selling through distribution channels and don't have the
resources to serve every end-user. However, we will try to do our best to help every
customer. Please also remember that for many of our technical support team English is a
second language, you will have a better chance of getting a helpful answer if your
question can be understood in the first place. Be sure to use very, simple, concise
language that clearly states the problem, avoid rambling or flowery language and always
list your system components. Here is the contact information for our branch offices:
IS7-V
How to Get Technical Support
H-3
North America and South America:
Japan:
ABIT Computer (U.S.A.) Corporation
45531 Northport Loop West,
Fremont, California 94538, U.S.A.
Tel: 1-510-623-0500
Fax: 1-510-623-1092
[email protected]
[email protected]
http://www.abit-usa.com
ABIT Computer (Japan) Co. Ltd.
Fax: 81-3-5396-5110
http://www.abit4u.jp
U.K. and Ireland:
ABIT Computer (U.K.) Corporation
Ltd.
Unit 3, 24-26 Boulton Road,
Stevenage, Herts SG1 4QX, U.K.
Tel: 44-1438-228888
Fax: 44-1438-226333
[email protected]
[email protected]
Germany, Benelux (Belgium,
Netherlands, Luxembourg), Denmark,
Norway, Sweden, Finland, and
Switzerland:
AMOR Computer B.V. (ABIT’s
European Office)
Van Coehoornstraat 7,
5916 PH Venlo, The Netherlands
Tel: 31-77-3204428
Fax: 31-77-3204420
[email protected]
[email protected]
http://www.abit.nl
Austria, Czech, Romania, Bulgaria,
Yugoslavia, Slovakia, Slovenia, Croatia,
Bosnia, Serbia, and Macedonia:
Asguard Computer Ges.m.b.H
Schmalbachstrasse 5,
A-2201 Gerasdorf/Wien, Austria
Tel: 43-1-7346709
Fax: 43-1-7346713
[email protected]
Shanghai:
ABIT Computer (Shanghai) Co. Ltd.
Tel: 86-21-6235-1829
Fax: 86-21-6235-1832
http://www.abit.com.cn
Russia:
ABIT Computer (Russia) Co. Ltd.
Fax: 7-095-937-2837
[email protected]
http://www.abit.ru
France, Italy, Spain, Portugal, and
Greece:
ABIT Computer France SARL
Tel: 33-1-5858-0043
Fax: 33-1-5858-0047
http://www.abit.fr
All other territories not covered above
please contact Taiwan Head Office:
When contacting our headquarters please
Note we are located in Taiwan and we are
8+ GMT time. In addition, we have
holidays that may be different from those
in your country.
ABIT Computer Corporation
No.323, Yang Guang St., Neihu, Taipei,
114, Taiwan
Tel: 886-2-8751-8888
Fax: 886-2-8751-3382
[email protected]
[email protected]
[email protected]
http://www.abit.com.tw
User’s Manual
H-4
Appendix H
7. RMA Service. If your system has been working but it just stopped, but you have not
installed any new software or hardware recently, it is likely that you have a defective
component. Please contact the reseller from whom you bought the product. You should be
able to get RMA service there.
8. Reporting Compatibility Problems to ABIT. Because of tremendous number of email
messages we receive every day, we are forced to give greater weight to certain types of
messages than to others. For this reason, any compatibility problem that is reported to us,
giving detailed system configuration information and error symptoms will receive the
highest priority. For the other questions, we regret that we may not be able to reply
directly. But your questions may be posted to the Internet news group in order that a
larger number of users can have the benefit of the information. Please check the news
group from time to time.
9. The information listed below are some chipset vendors’ WEB site addresses for your
reference:
HighPoint Technology Inc.’s WEB site: http://www.highpoint-tech.com/
Intel’s WEB site: http://www.intel.com/
Silicon Image’s WEB site: http://www.siimage.com/
SiS’ WEB site: http://www.sis.com.tw/
VIA’s WEB site: http://www.via.com.tw/
Thank You
ABIT Computer Corporation
http://www.abit.com.tw
IS7-V

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement