Makita 1051D Instruction manual

ENGLISH (Original instructions)
INSTRUCTION MANUAL
Cordless Power Planer
1051D
002541
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE.
1
ENGLISH (Original instructions)
SPECIFICATIONS
Model
1051D
Planing width
50 mm
Planing depth
0.5 mm
Shiplapping depth
15 mm
No load speed (min-1)
9,000
Overall length
297 mm
Net weight
2.3 kg
Rated voltage
D.C.14.4V
• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
• Specifications and battery cartridge may differ from country to country.
• Weight, with battery cartridge, according to EPTA-Procedure 01/2003
END004-4
ENG901-1
•
Symbols
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
Read instruction manual.
Cd
Ni-MH
Li-ion
•
Only for EU countries
Do not dispose of electric equipment or
battery pack together with household
waste material!
In observance of European Directive
2002/96/EC on waste electric and
electronic equipment, 2006/66/EC on
batteries and accumulators and waste
batteries and accumulators and their
implementation in accordance with
national laws, electric equipment and
battery pack that have reached the end
of their life must be collected separately
and returned to an environmentally
compatible recycling facility.
•
•
The declared vibration emission value has been
measured in accordance with the standard test
method and may be used for comparing one tool
with another.
The declared vibration emission value may also be
used in a preliminary assessment of exposure.
WARNING:
The vibration emission during actual use of the
power tool can differ from the declared emission
value depending on the ways in which the tool is
used.
Be sure to identify safety measures to protect the
operator that are based on an estimation of
exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it
is running idle in addition to the trigger time).
ENH101-13
For European countries only
ENE001-1
EC Declaration of Conformity
Intended use
The tool is intended for planing wood.
We Makita Corporation as the responsible
manufacturer declare that the following Makita
machine(s):
Designation of Machine:
Cordless Power Planer
ENG104-2
Noise
The typical A-weighted noise level determined according
to EN60745:
Sound pressure level (LpA) : 73 dB(A)
Uncertainty (K) : 3 dB(A)
The noise level under working may exceed 80 dB (A).
Wear ear protection.
Model No./ Type: 1051D
are of series production and
Conforms to the following European Directives:
98/37/EC until 28th December 2009 and then with
2006/42/EC from 29th December 2009
And are manufactured in accordance with the following
standards or standardised documents:
EN60745
The technical documentation is kept by our authorised
representative in Europe who is:
Makita International Europe Ltd,
ENG242-1
Vibration
The vibration total value (tri-axial vector sum) determined
according to EN60745:
Work mode : planing softwood
Vibration emission (ah) : 2.5 m/s2 or less
Uncertainty (K) : 1.5 m/s2
2
increase the risk of electric shock.
When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.
9.
If operating a power tool in a damp location is
unavoidable, use a ground fault circuit
interrupter (GFCI) protected supply. Use of an
GFCI reduces the risk of electric shock.
Personal safety
10. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or
medication. A moment of inattention while
operating power tools may result in serious
personal injury.
11. Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
12. Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools with
your finger on the switch or energising power tools
that have the switch on invites accidents.
13. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.
14. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
15. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing, and gloves
away from moving parts. Loose clothes,
jewellery or long hair can be caught in moving
parts.
16. If devices are provided for the connection of
dust extraction and collection facilities,
ensure these are connected and properly used.
Use of dust collection can reduce dust-related
hazards.
Power tool use and care
17. Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
18. Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot
be controlled with the switch is dangerous and
must be repaired.
Michigan, Drive, Tongwell,
Milton Keynes, MK15 8JD, England
8.
30th January 2009
000230
Tomoyasu Kato
Director
Makita Corporation
3-11-8, Sumiyoshi-cho,
Anjo, Aichi, JAPAN
GEA006-2
General Power Tool Safety
Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and
instructions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
1.
Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
2.
Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
3.
Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
Electrical safety
4.
Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
5.
Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of
electric shock if your body is earthed or grounded.
6.
Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
7.
Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords
3
GEB064-1
19.
Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such
preventive safety measures reduce the risk of
starting the power tool accidentally.
20. Store idle power tools out of the reach of
children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are
dangerous in the hands of untrained users.
21. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents
are caused by poorly maintained power tools.
22. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
23. Use the power tool, accessories and tool bits
etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the power
tool for operations different from those intended
could result in a hazardous situation.
Battery tool use and care
24. Recharge only with the charger specified by
the manufacturer. A charger that is suitable for
one type of battery pack may create a risk of fire
when used with another battery pack.
25. Use power tools only with specifically
designated battery packs. Use of any other
battery packs may create a risk of injury and fire.
26. When battery pack is not in use, keep it away
from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from one
terminal to another. Shorting the battery
terminals together may cause burns or a fire.
27. Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If
contact accidentally occurs, flush with water. If
liquid contacts eyes, additionally seek medical
help. Liquid ejected from the battery may cause
irritation or burns.
Service
28. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
29. Follow instruction for lubricating and
changing accessories.
30. Keep handles dry, clean and free from oil and
grease.
CORDLESS PLANER SAFETY
WARNINGS
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
Wait for the cutter to stop before setting the
tool down. An exposed cutter may engage the
surface leading to possible loss of control and
serious injury.
Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body
leaves it unstable and may lead to loss of control.
Rags, cloth, cord, string and the like should
never be left around the work area.
Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
Use only sharp blades. Handle the blades very
carefully.
Be sure the blade installation bolts are
securely tightened before operation.
Hold the tool firmly with both hands.
Keep hands away from rotating parts.
Before using the tool on an actual workpiece,
let it run for a while. Watch for vibration or
wobbling that could indicate poor installation
or a poorly balanced blade.
Make sure the blade is not contacting the
workpiece before the switch is turned on.
Wait until the blade attains full speed before
cutting.
Always switch off and wait for the blades to
come to a complete stop before any adjusting.
Never stick your finger into the chip chute.
Chute may jam when cutting damp wood.
Clean out chips with a stick.
Do not leave the tool running. Operate the tool
only when hand-held.
Always change both blades or covers on the
drum, otherwise the resulting imbalance will
cause vibration and shorten tool life.
Use only Makita blades specified in this
manual.
Always use the correct dust mask/respirator
for the material and application you are
working with.
SAVE THESE INSTRUCTIONS.
WARNING:
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product.
MISUSE or failure to follow the safety rules stated in
this instruction manual may cause serious personal
4
injury.
3.
Charge the battery cartridge with room
temperature at 10 C - 40 C (50 F - 104 F).
Let a hot battery cartridge cool down before
charging it.
Charge the Nickel Metal Hydride battery
cartridge when you do not use it for more than
six months.
ENC004-2
IMPORTANT SAFETY
INSTRUCTIONS
4.
FOR BATTERY CARTRIDGE
1.
Before using battery cartridge, read all
instructions and cautionary markings on (1)
battery charger, (2) battery, and (3) product
using battery.
2.
Do not disassemble battery cartridge.
3.
If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4.
If electrolyte gets into your eyes, rinse them
out with clear water and seek medical
attention right away. It may result in loss of
your eyesight.
5.
Always cover the battery terminals with the
battery cover when the battery cartridge is not
used.
6.
Do not short the battery cartridge:
(1) Do not touch the terminals with any
conductive material.
(2) Avoid storing battery cartridge in a
container with other metal objects such as
nails, coins, etc.
(3) Do not expose battery cartridge to water
or rain.
A battery short can cause a large current
flow, overheating, possible burns and
even a breakdown.
7.
Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50 C (122 F).
8.
Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a fire.
9.
Be careful not to drop or strike battery.
10. Do not use dropped or struck battery.
FUNCTIONAL DESCRIPTION
•
CAUTION:
Always be sure that the tool is switched off and the
battery cartridge is removed before adjusting or
checking function on the tool.
Installing or removing battery cartridge
2
1
002545
Always switch off the tool before insertion or
removal of the battery cartridge.
To remove the battery cartridge, withdraw it from
the tool while pressing the buttons on both sides of
the cartridge.
To insert the battery cartridge, align the tongue on
the battery cartridge with the groove in the housing
and slip it into place. Always insert it all the way
until it locks in place with a little click. If not, it may
accidentally fall out of the tool, causing injury to you
or someone around you.
Do not use force when inserting the battery
cartridge. If the cartridge does not slide in easily, it
is not being inserted correctly.
•
•
•
•
Adjusting depth of cut
2
SAVE THESE INSTRUCTIONS.
Tips for maintaining maximum battery life
1.
2.
1. Button
2. Battery cartridge
1
1. Pointer
2. Scale
3. Knob
3
Charge the battery cartridge before completely
discharged.
Always stop tool operation and charge the
battery cartridge when you notice less tool
power.
Never recharge a fully charged battery
cartridge.
Overcharging shortens the battery service life.
002547
The depth of cut can be adjusted in 0.1 mm increments
within a range of 0 - 0.5 mm. Turn the knob on the front of
the tool until the pointer is aligned with the desired cutting
depth on the scale.
5
•
CAUTION:
The knob can be turned beyond the 0.5 mm
graduation. However, do not operate the tool with a
depth of cut more than 0.5 mm The motor may be
burned out or the battery cartridge may be
damaged.
1. Installation bolts
2. Hex wrench
1
2
Switch action
002557
1. Lock-off button
2. Switch trigger
1
Push the blade from the belt side with the hex wrench.
Remove the other blade in the same manner.
2
1. Hex wrench
2. Planer blade
1
2
002551
CAUTION:
Before inserting the battery cartridge into the tool,
always check to see that the switch trigger actuates
properly and returns to the "OFF" position when
released.
To prevent the switch trigger from being accidentally
pulled, a lock-off button is provided.
To start the tool, depress the lock-off button and pull the
switch trigger. Release the switch trigger to stop.
•
002558
To install the blades, first clean out all chips or foreign
matter adhering to the drum or blades. Insert the blade
between the drum and the drum cover from the side
opposite the belt so that the blade end will protrude
slightly from the side of the drum.
Tighten the two installation bolts securely with the hex
wrench.
ASSEMBLY
1
•
2
CAUTION:
Always be sure that the tool is switched off and the
battery cartridge is removed before carrying out
any work on the tool.
3
4
1. Drum cover
2. Installation bolts
3. Planer blade
4. Side of drum
5. Drum
Removing or installing planer blades
5
CAUTION:
Tighten the blade installation bolts carefully when
attaching the blades to the tool. A loose installation
bolt can be dangerous. Always check to see they
are tightened securely.
•
Handle the blades very carefully. Use gloves or
rags to protect your fingers or hands when
removing or installing the blades.
•
Use only the Makita wrench provided to remove or
install the blades. Failure to do so may result in
overtightening or insufficient tightening of the
installation bolts. This could cause an injury.
To remove the blades, first loosen the two installation
bolts one turn counterclockwise with the hex wrench.
002559
•
Blade height adjustment
1
1. Pan head
screws
2. Installation bolts
2
002567
Blade height adjustment is usually not necessary.
However, if you notice that the blade edge is below the
level of the rear base or protrudes too far from the rear
base, proceed as follows.
6
thumb screw (A). Loosen the thumb screw (B) and adjust
the edge fence until it comes in contact with the side of
the workpiece. Then tighten the thumb screw (B)
securely.
You may wish to add to the length of the fence by
attaching an extra piece of wood. Convenient holes are
provided in the fence for this purpose.
Loosen the two installation bolts. Turn the pan head
screws
clockwise
to
retract
the
blade
or
counterclockwise to protrude it. After adjusting the blade
height, tighten the two installation bolts securely.
Hex wrench storage
1. Hex wrench
1
002569
When not in use, store the hex wrench as shown in the
figure to keep it from being lost.
002574
Dust bag
OPERATION
Planing operation
1. Dust bag
2. Nozzle
3. Fastener
2
1
1. Start
2. End
1
2
3
002572
Install the dust bag on the nozzle of the tool. When
installing it, push the bag's entry port toward the nozzle
as far as it will go to prevent it from coming off during
operation.
For the best results, empty the dust bag when it becomes
about half full. Remove the dust bag from the tool and
pull out the fastener.
002577
First, rest the tool front base flat upon the workpiece
surface without the blades making any contact. Switch
on and wait until the blades attain full speed. Then move
the tool gently forward. Apply pressure on the front of tool
at the start of planing, and at the back at the end of
planing. Planing will be easier if you incline the workpiece
in stationary fashion, so that you can plane somewhat
downhill.
The speed and depth of cut determine the kind of finish.
The power planer keeps cutting at a speed that will not
result in jamming by chips. For rough cutting, the depth of
cut can be increased, while for a good finish you should
reduce the depth of cut and advance the tool more
slowly.
NOTE:
•
If you connect a Makita vacuum cleaner to this tool,
more efficient and cleaner operations can be
performed.
Edge fence (Guide rule)
1
1. Thumb screw (A)
2. Washer
3. Edge fence
4. Thumb screw (B)
2
4
3
002573
Use the edge fence when shiplapping (rabbeting) or
cutting workpieces nearly 50 mm wide. Install the edge
fence on the tool and secure it with the washer and
7
Shiplapping (Rabbeting)
1. V groove
1
002586
MAINTENANCE
002580
To make a stepped cut as shown in the figure, use the
edge fence (guide rule).
Draw a cutting line on the workpiece. Align the blade
edge with the cutting line. Then adjust the edge fence as
explained in the "Edge fence" section.
CAUTION:
Always be sure that the tool is switched off and the
battery cartridge is removed before attempting to
perform inspection or maintenance.
•
Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may
result.
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized Service Centers, always
using Makita replacement parts.
•
1. Blade edge
2. Side of drum
3. Cutting line
3
1 2
ACCESSORIES
002581
When planing, move the tool with the edge fence flush
with the side of the workpiece. Otherwise uneven planing
may result.
Maximum shiplapping (rabbeting) depth is 15 mm.
•
CAUTION:
These
accessories
or
attachments
are
recommended for use with your Makita tool
specified in this manual. The use of any other
accessories or attachments might present a risk of
injury to persons. Only use accessory or
attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
•
Mini planer blade
•
Dust bag
•
Various type of Makita genuine batteries and
chargers
•
CAUTION:
Before shiplapping, adjust the blade so that the end
protrudes slightly from the side of the drum.
Chamfering
To make a chamfering cut as shown in the figure, align
the "V" groove in the front base with the edge of the
workpiece and plane it.
It chamfers up to 5.6 mm in a single pass.
5.6 mm (7/32")
5.6 mm (7/32")
002585
8
9
10
11
Makita Corporation Anjo, Aichi, Japan
884326F222
12