Motorola CPEi 800 Series User manual

CPEi 800/825
Series
User Manual
* Please see the Introduction Section
Contents
Introduction ..............................................................................................................................iii
Chapter 1: CPEi 800/825 User Guide
Overview .......................................................................................................................................... 1-1
Powerful Features in a Single Unit .................................................................................................. 1-2
Front of the CPE .............................................................................................................................. 1-2
Back of the CPE ............................................................................................................................... 1-3
Operating Information ..................................................................................................................... 1-3
Chapter 2: Installation
Overview .......................................................................................................................................... 2-1
Before you Begin.............................................................................................................................. 2-1
Easy Setup ....................................................................................................................................... 2-1
Advanced Setup ............................................................................................................................... 2-2
Procedure to Log into the CPE ........................................................................................................ 2-2
Setup Wizard and Authentication .................................................................................................... 2-3
Restart Button.................................................................................................................................. 2-5
Chapter 3: Basic Configuration
Before you Begin.............................................................................................................................. 3-1
Personalize Menu............................................................................................................................. 3-1
Password Tab ................................................................................................................................... 3-2
Device Time Tab .............................................................................................................................. 3-2
Device Name Tab ............................................................................................................................. 3-2
Restore Factory Settings Tab........................................................................................................... 3-3
Internet Menu .................................................................................................................................. 3-3
WiMAX Security Tab ........................................................................................................................ 3-4
Internet Protocol Tab ....................................................................................................................... 3-4
Firewall Tab ..................................................................................................................................... 3-4
Dynamic DNS Tab ............................................................................................................................ 3-5
Status Menu..................................................................................................................................... 3-5
Network Tab .................................................................................................................................... 3-6
Telephony Tab (CPEi 825 Models only) ........................................................................................... 3-6
Telephony Menu (CPEi 825 Models only) ........................................................................................ 3-6
Account Tab ..................................................................................................................................... 3-7
AUG 2011
i
Ring Tone Tab .................................................................................................................................. 3-8
Caller ID Tab.................................................................................................................................... 3-8
Call Forwarding Tab ........................................................................................................................ 3-8
Voice Mail Tab ................................................................................................................................. 3-9
Special Number Tab ........................................................................................................................ 3-9
Chapter 4: Advanced Configuration
Port Forwarding Menu..................................................................................................................... 4-1
Forwarding Tab ............................................................................................................................... 4-2
Local Address Menu......................................................................................................................... 4-2
DHCP Server Tab............................................................................................................................. 4-3
Lease Status Tab.............................................................................................................................. 4-4
Lease Reservation Tab ..................................................................................................................... 4-4
Control Panel ................................................................................................................................... 4-5
Software Tab.................................................................................................................................... 4-6
Certificate Tab ................................................................................................................................. 4-6
System Tab ...................................................................................................................................... 4-6
About Tab......................................................................................................................................... 4-6
Chapter 5: Configuring TCP/IP
Configuring TCP/IP in Windows 2000.............................................................................................. 5-1
Configuring TCP/IP in Windows XP ................................................................................................. 5-5
Chapter6: Troubleshooting
Power ............................................................................................................................................... 6-1
A Computer Cannot Log On to the CPE ........................................................................................... 6-1
Cannot Connect to the Internet ....................................................................................................... 6-1
Additional Troubleshooting Help ..................................................................................................... 6-1
Chapter 7: Important Safety and Legal Information ........................................ 7-1
ii
AUG 2011
Introduction
Introduction
This User Manual is for the Nokia Siemens Networks CPEi 800 and CPEi 825 models of desktop
modems. The specific model numbers and additional details are included in the table below.
Table i-1 Desktop Modem Models - Data Only
Data Only Models
CPEi 23800
CPEi 25800
CPEi 35800
Table i-2 Desktop Modem Models - Data Plus VoIP
Data Plus VoIP (Voice over Internet Protocol) Models
CPEi 23825
CPEi 25825
CPEi 35825
Throughout this manual, references made to VoIP are applicable only to the CPEi 825 series of
products. The CPEi 800 series of products do not include the RJ-11 telephone connector on the back
of the device, the telephony LED or any reference to telephony in the Graphical User Interface
(GUI).
AUG 2011
iii
CPEi 800/825 User Guide
1
Chapter 1: CPEi 800/825 User Guide
Overview
Thank you for purchasing the Nokia Siemens Networks CPE Indoor CPEi 800/825 desktop device.
The Desktop CPEi 800/825 allows you to connect to the wireless world easily and seamlessly
without complicated installation and setup procedures. In addition, it offers you the ability to make
Voice over Internet Protocol (VoIP) calls.
The Desktop CPE indoor CPEi 800/825 device provides the user:

Convenience - with easy plug and play functionality. Compact design.

Control - remote management capability allows easy detection and authentication when the unit
is set up.

VoIP - RJ11 port allows for Voice over IP calls using your CPEi 825.
The features and the physical appearance of your Desktop CPEi 800/825 device may differ slightly
from the illustration.
Figure 1-1: CPEi 800/825
CPEi 800
CPEi 825
For the most recent documentation, visit the Product Documentation page on
www.nokiasiemensnetworks.com/devices.
AUG 2011
1-1
1
CPEi 800/825 User Guide
Powerful Features in a Single Unit
The CPE device provides the following features:

WiMAX Authentication

WAN DHCP Client

LAN DHCP Server

Home Gateway Functions

Firewall Protection

Port Forwarding
Front of the CPE
The front of the CPE unit contains LED Link/Activity indicators. The LEDs show the status of the
unit and signal strength indicators for easy adjustment during setup.
Table 1-1 LED Indicator Interface
LED
Status
Signal Strength
Full WiMAX Signal Strength is detected when all WiMAX Signal Strength
LEDs are lit.
WAN WiMAX

All WiMAX Signal Strength LEDs are off - very low signal detected.

One to two WiMAX Signal Strength LEDs are lit - low signal detected.

Three to five WiMAX Signal Strength LEDs are lit - high signal
detected.
While acquiring access to the WiMAX Network:

All WiMAX Signal Strength LEDs vary between ON, OFF and/or
BLINKING status.
If all five WiMAX Signal Strength LEDs are blinking, then a software upgrade is in progress. Do
NOT remove power to the CPE.
1-2
AUG 2011
CPEi 800/825 User Guide
1
Back of the CPE
The back of the CPE unit contains the RESET switch, DC Power Connector, Ethernet connector
(RJ-45), Ethernet LED and ATA port (RJ-11).
Figure 1-2: CPE Ports and Connections
CPEi 800
CPEi 825
Table 1-2 Port Descriptions
Port
Description
Ethernet
Ethernet Port.
Power
DC Power Connector.
Reset
Hardware Reset Button (A paperclip is recommended for
accessing this button).
Phone Line
RJ-11 port for use with VoIP.
Operating Information
Operating temperature for this unit is 0-40°C (32-104°F).
AUG 2011
1-3
Installation
2
Chapter 2: Installation
Overview
To install the Desktop CPEi 800/825 Series, review the following sections:

Before You Begin

Easy Setup
Before you Begin
Before you begin installation, check that you have received the following items with your Desktop
CPEi 800/825:
Table 2-1 In the box with your CPE, you should have
Item
Description
AC Power Adapter
Power adapter cord connects the Desktop CPE to an
AC electrical outlet.
Ethernet Cable
The Ethernet cable connects the Internet port on your
Desktop CPE to your PC or laptop computer.
Desktop CPEi 800/825 Quick Start Guide
Desktop CPEi 800/825 Quick Start Guide.
Desktop CPEi 800/825 Regulatory Guide
Desktop CPEi 800/825 Regulatory Guide.
In addition, you need:
 A computer
 An RJ-11 telephone cable (if applicable)
Easy Setup
The CPE is easily set up in your home. Basic installation equipment needed are the power adapter
and cord, Ethernet cable, a PC or laptop computer and the CPE device. If you want to use the VoIP
functionality, you need an RJ-11 phone cable and a telephone.
Perform the following tasks before attaching the power cord or powering up the unit:

Stand the CPE on a flat surface.

Plug the power adapter into the power connector on the back of the unit.

Plug the AC power cord into an AC outlet.

Plug one end of the Ethernet cable into the Ethernet connector on the back of the unit.

Plug the other end of the Ethernet cable into the Ethernet connector of your computer.

To use VoIP functionality of the phone, plug one end of the phone line into the activated phone
connector on the back of the unit. Phone line activation is dependent upon your service contract.

Plug the other end of the phone line into the phone line connector of your telephone.
AUG 2011
2-1
2
Installation
Advanced Setup
The CPE can also be used to connect to a multi-port switch (hub) – purchased separately from the
CPE. Connecting the CPE device to a hub allows you to connect more than one computer to your
CPE device.
Procedure to Log into the CPE
Before you Begin Configuration
Some settings on your computer need to be verified or changed to ensure that your computer
configuration can support the Desktop CPE.
Verify that the IP addresses and DNS settings are automatically generated in the Local Area
connection of your Internet Protocol (TCP/IP) properties. Refer to the chapter titled “Configuring
TCP/IP” for additional information.
Logging in to the CPE
Use the following procedure to log into the Desktop CPE:
1.
2.
On a computer that is connected to the Desktop CPE, open a web browser.
In the Address or Location field, type http://mywimax. and press ENTER to display the login
screen.
Include the period (.) after http://mywimax. in order to access the login screen.
Alternatively, you may enter the IP address: http://192.168.15.1 into the Address field in order to
gain access to your CPE. If you cannot access the CPE, refer to the chapter titled: Configuring
TCP/IP for more information.
3.
The Welcome to Nokia Siemens Networks WiMAX CPE screen is displayed and prompts you for
a password.
2-2
AUG 2011
Installation
2
Figure 2-1: Login Screen
4.
5.
6.
7.
In the password field, type the password (default is nsn).
Click Login.
First time users see a pop-up box that states: “The Wizard application will guide you through
for the first time configuration”. Click OK to continue.
Click the OK to launch the wizard application.
In some earlier versions of software, the default password is motorola.
Setup Wizard and Authentication
Step 1 - Change Password
After you have launched the setup wizard, you are prompted to change your password. Nokia
Siemens Networks recommends using a password to protect your home network and CPE device.
Passwords are case sensitive.
To change your password:

Ensure the “Enable Login Password Protection” box is checked.

Enter a New Login Password in the box. Passwords can be no more than 20 characters in length.

Re-type your new password in the Confirm New Login Password box.

Click Next.
If you forget your password, you can reset it back to the default (nsn) password. To reset the
password, press and hold the reset button on the back of your CPE for 7 or more seconds. Before
resetting the CPE, ensure that the power is ON.
AUG 2011
2-3
2
Installation
In some earlier versions of software, the default password is motorola.
Step 2 - Device Time
This screen allows you to set the time zone and to enable Daylight Savings Time (when applicable)
for your location.

Select the appropriate time zone for your location from the drop-down box.

Check “Auto Adjust for Daylight Savings Time” if you live in a region that observes Daylight
Savings Time. This box is checked by default.

Click Next.
Step 3 - WiMAX Security
The WiMAX Security tab contains your authentication method. Check with your service provider to
determine if they require a user name and password for authentication purposes.

If the Authentication Method is EAP-TLS, a User Name and Password is not required. Enter the
Realm information supplied by your service provider. Click Next.

If the Authentication Method is EAP-TTLS/MS-CHAPv2, enter User Name and Password, and
Realm information supplied by your Service Provider. When you have entered the User
Name/Password/Realm information, click Next.

If you are unsure of the Authentication Method, select EAP-TLS (which is the default) and click
Next.
Step 4 – Account
The Account tab allows you to manage Voice over IP (VoIP) related services. Please consult with
your telephony service provider for these settings.
Click Apply when finished.
Congratulations! You have now completed the setup of your WiMAX connection.
Click OK on the Congratulations! dialog box.
A status screen appears that shows Network status and telephony status. The Network Status
screen provides any status associated with your WiMAX Wireless Broadband connection. The
Telephony Status screen provides status of your telephony service.

Restart is used to restart the device. The restart button is available on every screen.

Wizard starts the set-up wizard over again.

Refresh refreshes the screen with the current status.

Auto Refresh allows the web browser to automatically refresh at the interval determined in the
Control Panel menu.
2-4
AUG 2011
Installation
2
Figure 2-2: Status Screen
Restart Button
Figure 2-3: Restart Button
Restart Wizard
Refresh
Auto Refresh
AUG 2011
2-5
Basic Configuration
3
Chapter 3: Basic Configuration
Before you Begin
When the CPE setup has been completed, you can log in to your CPE from any computer on your
home network. To log in, type the device name in the address bar on your computer. The default
device name is mywimax.
This section describes the PERSONALIZE, INTERNET and STATUS Menus that are available.
Personalize Menu
The Personalize menu provides the following tabs:

Password

Device Time

Device Name

Restore Factory Settings
Figure 3-1: Personalize Menu
To Access the Personalize menu, click the Computer icon, then click Personalize.
AUG 2011
3-1
3
Basic Configuration
Password Tab
The password tab allows you to enable/disable password protection. You can also change your
password here. Click Apply when finished.
Table 3-1 Password Tab
Field or Button
Description
Enable Login Password Protection
Checking this box requires login password protection.
New Login Password
Enter your new password here. Maximum 20 characters.
Passwords are case sensitive.
Confirm New Login Password
Re-enter your new password here, exactly as entered in the
previous step.
Device Time Tab
The Device Time tab allows you to establish the time zone for your location. It also allows you to
automatically adjust for Daylight Savings Time if necessary. Click Apply when finished.
Table 3-2 Device Time Tab
Field or Button
Description
Current Local Time
Current Local Time
Time Zone
Select your local time zone from the dropdown box.
Auto Adjust for Daylight Saving Time
Check this box if your location observes Daylight Savings
Time (Default is checked).
Device Name Tab
The Device Name tab allows you to rename your CPE device. The Device Name is the name you
enter on an internet browser address bar to access your CPE device. Click Apply when finished.
Table 3-3 Device Name Tab
Field or Button
Description
New Device Name
Enter the new name for the CPE device. Maximum 20
characters.
3-2
AUG 2011
Basic Configuration
3
Restore Factory Settings Tab
The Restore Factory Settings Tab resets your CPE to the manufacturer default settings. Click Apply
if you are sure you want to reset factory settings.
Table 3-4 Restore Factory Settings Tab
Field or Button
Description
Restore Factory Settings
Checking this box restores the CPE to factory default
settings. The device restarts when you click Apply.
Internet Menu
The Internet menu provides the following tabs:

WiMAX Security

Internet Protocol

Firewall

Dynamic DNS
Figure 3-2: Internet Menu
To access the Internet menu, click the Computer icon, then click Internet.
AUG 2011
3-3
3
Basic Configuration
WiMAX Security Tab
The WiMAX Security tab contains your authentication method. Check with your service provider to
determine if user name and password are required for authentication purposes.
Table 3-5 WiMAX Security Tab
Field or Button
Description
Authentication Method
Drop down box allows you to select either EAP-TLS
(default) or EAP-TTLS/MSCHAPv2.
User Name (EAP-TTLS/MS-CHAPv2
only)
Enter the User Name supplied by your service provider.
Password (EAP-TTLS/MS-CHAPv2 only)
Enter the Password supplied by your service provider.
Realm
Supplied by your service provider.
If your authentication method is EAP-TLS, a User Name and Password is not required. Click Apply.
Internet Protocol Tab
Check with your service provider for these settings. If you are unsure of the settings, leave the
default values set. Click Apply.
If your service provider has instructed you to change any of these settings, click Apply when
finished.
Firewall Tab
A firewall helps to protect your home network from unauthorized access. It also helps to manage
authorized access from the internet to your CPE.
Table 3-6 Firewall Tab
Field or Button
Description
Enable Firewall
Check this box to enable the firewall for your home
network.
Enable Web Login from Internet
(Grayed out if Enable Firewall is not selected).
Checking this box enables you to access your CPE device
from a network other than your own.
Web Login Port from Internet
Choose a port number to connect to when logging in
from a network other than your own. The default is 8080.
Enable ping from Internet
Enables the CPE to respond to a ping from the Internet.
This option is enabled to allow testing only. Do not leave
this enabled.
Click Apply when you are finished.
3-4
AUG 2011
Basic Configuration
3
Dynamic DNS Tab
Dynamic Domain Name Service (DDNS) allows a user with a non-static IP address to keep their
domain name associated with an ever changing IP address. As an example, DDNS is used when you
are hosting your own website.
Table 3-7 Dynamic DNS Tab
Field or Button
Description
Enable DDNS
Check this box to Enable DDNS (default is unchecked).
DDNS Service Provider
Select DDNS Service Provider that you belong to from
the drop-down box.
DDNS User Name
Only valid if Enable DDNS is checked. Enter your DDNS
account user name.
DDNS Password
Only valid if Enable DDNS is checked. Enter your DDNS
account password.
DDNS Host Name
Only valid if Enable DDNS is checked. Enter the DDNS
Host Name. This is assigned by the DDNS service.
Click Apply when you are finished.
Status Menu
The Status menu provides the following tabs:

Network

Telephony
AUG 2011
3-5
3
Basic Configuration
Figure 3-3: Status Menu
Network Tab
The Network tab provides any status associated with your WiMAX Wireless Broadband connection.
Telephony Tab (CPEi 825 Models only)
The Telephony tab provides any status associated with your telephony connection.
Telephony Menu (CPEi 825 Models only)
The telephony menu allows you to manage your Voice over Internet Protocol (VoIP) services.
Contact your service provider to obtain VoIP service.
The Telephony menu provides the following tabs:

Account

Ring Tone

Caller ID
3-6
AUG 2011
Basic Configuration

Call Forwarding

Voice Mail

Special Numbers
3
Figure 3-4: Telephony Menu
Account Tab
Consult your service provider for these settings.
Table 3-8 Account Tab
Field or Button
Description
User Name
If Line is an active VoIP, enter the User Name as provided by
your service provider.
Password
Enter the Line password as provided by your service provider.
Passwords are case sensitive.
Confirm Line Password
Re-enter your Line password exactly as entered in the field from
the previous step.
Click Apply when you are finished.
AUG 2011
3-7
3
Basic Configuration
Ring Tone Tab
The Ring Tone tab allows you to customize ring tones for your telephone(s).
You need a phone connected to your CPE to hear ring tones.
Table 3-9 Ring Tone Tab
Field or Button
Description
Default Line Ring Type
Use the drop-down box to select a ring tone for Line. The
default is ring tone R0.
Test
Click to hear how the selected ring tone sounds.
Click Apply when you are finished.
Caller ID Tab
The Caller ID tab allows you to manage the Caller ID functions for your telephone(s).
Table 3-10 Caller ID Tab
Field or Button
Description
Enable Line Anonymous Incoming Call
Rejection
If Line is your active telephone port, check this box to
reject telephone calls from anonymous incoming callers.
The default is checked.
Enable Line Permanent Anonymous
Outgoing Call
If Line is your active telephone port, check this box to
permanently block your telephone number from
appearing on others’ Caller ID. The default is unchecked.
Click Apply when you are finished.
Call Forwarding Tab
The Call Forwarding tab allows you to manage the call forwarding features for your telephone(s).
Table 3-11 Call Forwarding Tab
Field or Button
Description
Enable Line Basic Forwarding
Check this box to enable basic call forwarding on Line. The
default is unchecked.
Line Basic Forwarding to Number
If “Enable Line Basic Forwarding” is checked, enter the
telephone number you would like to forward calls to.
(Continue)
3-8
AUG 2011
Basic Configuration
3
Table 3-11 Call Forwarding Tab (Continued)
Field or Button
Description
Enable Line Forwarding on No
Answer
Check this box to forward calls received on Line if there is
no answer. This function is not available if “Enable Line
Basic Forwarding” is checked.
Line No Answer Forwarding to
Number
If “Line No Answer Forwarding to Number” is checked,
enter the telephone number you would like to forward calls
to when there is no answer on Line. This function is not
available if “Enable Line Basic Forwarding” is checked.
Line No Answer Forwarding Ring
Count
Enter the number of rings allowed before the call forwards
to the number identified above. The default is six rings.
Enable Line Forwarding on Busy
Check this box to forward calls received while Line is in
use.
Line Busy Forwarding To Number
If “Enable Line Forwarding on Busy” is checked, enter the
telephone number you would like calls forwarded to when
Line is in use.
Click Apply when you are finished.
Voice Mail Tab
The voice mail tab allows you to see the status of your voice mail. Contact your service provider to
activate the voice mail feature if it is not already active.
Table 3-12 Voice Mail Tab
Field or Button
Description
Line Server Based Voice Mail Status
Shows the status of Line voice mail as either enabled or
disabled.
Line Number of New Voice Mails
Shows the number of new, unheard voice mails on Line.
Line Number of Old Voice Mails
Shows the number of previously heard voice mails on Line.
Click Apply when you are finished.
Special Number Tab
The Special Number tab provides a list of special dialing numbers for your VoIP Phone Service.
Table 3-13 Special Number Tab
Field or Button
Description
Service Provider Contact Number
Use this number to contact customer service for your service
provider.
(Continue)
AUG 2011
3-9
3
Basic Configuration
Table 3-13 Special Number Tab (Continued)
Field or Button
Description
Emergency Number
Dial this number to reach local emergency services.
Redial
Dial this number to redial the last number called.
Blind Call transfer
Dial this number to transfer a call directly to a third party.
Consultation Call Transfer
Dial this number to speak with the third party before you
transfer the call to them.
Call Hold
Dial this number to place your current call on hold.
Automatic Recall Activate
Dial this number to call back the number of the last incoming
call.
Automatic Recall Deactivate
Dial this number to automatically call back the last number
dialed when that number becomes available.
Call Forwarding Activate
Dial this number to forward your calls to a different number.
Call Forwarding Deactivate
Dial this number to deactivate call forwarding.
Call Forwarding Busy Activate
Dial this number to forward calls to a different number when
the line is busy.
Call Forwarding Busy Deactivate
Dial this number to de-activate calls from forwarding to a
different number when the line is busy.
Call Forwarding Busy Change
Number
Dial this number to change the phone number to which calls
will be forwarded when the line is busy.
Call Forwarding No Answer Activate Dial this number to forward calls to a different number when
there is no answer on Line.
Call Forwarding No Answer
Deactivate
Dial this number to de-activate calls from forwarding to a
different number when there is no answer on Line.
Call Forwarding No Answer Change Dial this number to change the phone number to which calls
Number
will be forwarded when there is no answer on Line.
Automatic Callback Activate
Dial this number to hear the most recent call you missed and
to return the call. If the number is busy, you can hang up.
When the number is available, your phone will ring. Pick up
your phone and the call will be connected.
Automatic Callback Deactivate
Dial this number to de-activate automatic callback.
Do Not Disturb Activate
Dial this number to have calls automatically routed to voice
mail.
Do Not Disturb Deactivate
Dial this number to cancel automatic call routing to voice
mail.
Calling Number Delivery Blocking
Dial this number to block your number from appearing on
the Caller ID of the people you call. Your calls may appear as
“Private” or “Anonymous”.
Line Blocking Deactivate
Dial this number to unblock your telephone number from
appearing on Caller ID.
(Continue)
3-10
AUG 2011
Basic Configuration
3
Table 3-13 Special Number Tab (Continued)
Field or Button
Description
Call Waiting Toggle
Dial this number to toggle between call waiting ON and call
waiting OFF.
Anonymous Call Rejection Activate
Dial this number to have anonymous calls rejected.
Anonymous Call Rejection
Deactivate
Dial this number to allow anonymous calls to go through.
AUG 2011
3-11
Advanced Configuration
4
Chapter 4: Advanced Configuration
The Advanced Configuration section describes the Port Forwarding, Local Address, and Control
Panel menus.
Port Forwarding Menu
Port forwarding enables you to direct incoming traffic to specific LAN hosts (computers on your
network) based on the protocol and port number. It is used to play Internet games or provide local
services (such as web hosting) for a LAN group.
To access the Port Forwarding menu, click the Computer icon, then click Port Forwarding.
The Port Forwarding menu provides the following tabs:

Basic

Forwarding
Figure 4-1: Port Forwarding
AUG 2011
4-1
4
Advanced Configuration
Table 4-1 Port Forwarding Menu
Field or Button
Description
Enable UPnP IGD
Enables the Universal Plug and Play (UPnP) Internet
Gateway Device (IGD) profile to allow certain Windows
applications to set up the port forwarding rule
dynamically when NAT is enabled on this device.
DMZ (DeMilitarized Zone) IP Address
Enter the DMZ IP Address.
Click Apply when you are finished.
Forwarding Tab
Click ADD to create additional Port Forwarding rules.
Table 4-2 Forwarding Tab
Field or Button
Description
Select
Select a box when you want to delete the specific row.
Protocol
Select TCP (Transmission Control Protocol) or UDP (User
Datagram Protocol).
WAN Port Start
Enter the beginning port range for external network access.
WAN Port End
Enter the ending port range for external network access.
LAN IP Address
Enter the IP address to host the service.
LAN Port Start
Enter the beginning port range for internal network access.
LAN Port End
Enter the ending port range for internal network access.
Enabled
Check to enable specific port forwarding.
Click Apply when you are finished.
Local Address Menu
The Local Address menu allows you to configure your Local Area Network (LAN) connections.
The Local Address menu provides the following tabs:

DHCP Server

Lease Status

Lease Reservation
To access the Local Address menu, click the Computer icon, then click Local Address.
4-2
AUG 2011
Advanced Configuration
4
Figure 4-2: Local Address Menu
DHCP Server Tab
The DHCP Server tab enables Dynamic Host Configuration Protocol (DHCP) server functionality on
the LAN, allowing the router to dynamically assign lease IP addresses to clients that connect to it
from the local network.
Table 4-3 DHCP Server Tab
Field or Button
Description
Enable DHCP Server
If selected, the DHCP server on the gateway assigns IP addresses
to the computers and other hosts on your network if they have
DHCP enabled. By default, the gateway server is enabled. If there
is another DHCP server running on your network (on another
router), disable one of the DHCP servers.
DHCP Server IP Address
Enter the default port forwarding LAN Client IP Address.
DHCP Starting IP Address
Sets the first IP address assigned by the DHCP server, in dotteddecimal format. It must be greater than the IP address value of the
gateway. For example, if the IP address of the gateway is
192.168.15.1(default), the starting IP address must be
192.168.15.2 (or higher).
(Continue)
AUG 2011
4-3
4
Advanced Configuration
Table 4-3 DHCP Server Tab (Continued)
Field or Button
Description
DHCP Ending IP Address
Sets the final IP address assigned by the DHCP server. If the
DHCP server runs out of DHCP addresses, users cannot access
network resources. If this happens, increase the Ending IP or
reduce the Lease Time.
DHCP Lease Time
Sets the time, in seconds, that a network computer remains
connected to the gateway using its current assigned IP address. At
the end of this time, the DHCP server renews the lease or assigns
the computer a new IP address. The default is 3600 seconds (one
hour). The maximum is 999999 seconds (about 278 hours).
Click Apply when you are finished.
Lease Status Tab
The Lease Status tab in the Local Address menu displays the active DHCP leases since the last
reboot.
Table 4-4 Lease Status Tab
Field or Button
Description
Client Host Name
Displays the client host name. The Name field is limited to 20
characters (only 5 appear in display).
MAC Address
Media Access Control (MAC) address.
IP Address
Shows the IP Address for each active lease.
Remaining Lease Duration
Shows the amount of time, in seconds, remaining in the lease.
Click Apply when you are finished.
Lease Reservation Tab
This tab allows you to manage the lease reservation so that the same client receives the same IP
address each time.
Table 4-5 Lease Reservation Tab
Field or Button
Description
Select
Select this box if you want to delete an established lease
reservation. Click Delete when you have selected the exception to
be deleted.
Client Host Name
Enter the client host name. The Name field is limited to 20
characters (only 5 appear in display).
(Continue)
4-4
AUG 2011
Advanced Configuration
4
Table 4-5 Lease Reservation Tab (Continued)
Field or Button
Description
MAC Address
Media Access Control (MAC) address. Enter the MAC address of
the device.
IP Address
Enter the IP address that you want assigned to the MAC Address.
Enabled
Clicking this box enables the lease reservation.
Click Apply when you are finished.
Control Panel
The Control Panel sections allow you to view/update your software information.
The Control menu provides the following tabs:

Software

Certificate

System

About
Figure 4-3: Control Panel Menu
AUG 2011
4-5
4
Advanced Configuration
Software Tab
The Software tab manages the software on your CPE device. It is also where you can upgrade
device software.
Use the BROWSE button to browse your computer for additional software packages. When you
have located the software package/update you would like to add to your device, click Upgrade.
You should see the available software updates in the “Available Software Packages” table. If you
cannot see the list, click View.
Select the software you would like to install, click Install.
If you would like to remove software, select the software package you would like to remove, click
Uninstall.
Certificate Tab
The Certificate tab is where you manage the certificates that are stored on the device.
Use the BROWSE button to locate the certificate file on your computer, and then click IMPORT.
Use the REMOVE button to remove any selected certificate(s).
System Tab
The system tab allows you to manage additional features of your CPE device.
Table 4-6 System Tab
Field or Button
Description
Language Used in User Interface
Select the desired language for the user interface. The
default language is English.
Background
Select the desired background color for the user
interface.
Enable WiMAX Radio Interface
Check this box to enable the WiMAX Radio Interface.
Auto Refresh Interval
Enter, in seconds, the interval for status Auto Refresh.
Valid range is 2 seconds - 9999 seconds. The default
value is 3 seconds.
About Tab
The About Tab displays basic properties of your CPE device such as: Part Number, Model ID,
Hardware Version, Serial Number, WiMAX MAC Address and the LAN MAC Address.
4-6
AUG 2011
Configuring TCP/IP
5
Chapter 5: Configuring TCP/IP
This section contains two examples of configuring TCP/IP in a Windows environment.
Most computers already have the TCP/IP configuration enabled. Use the following procedures to
verify the configuration is set up. Configure all client computers on your network for TCP/IP (the
protocol that controls communication among computers).
Two examples are provided in this document:

Configuring TCP/IP in Windows 2000

Configuring TCP/IP in Windows XP
Follow the instructions in your computer user manual for other Operating Systems.
Configuring TCP/IP in Windows 2000
1.
2.
On the Windows desktop, click Start.
Select Settings and then Control Panel from the pop-up menus to display the Control Panel
window:
Figure 5-1: Windows Control Panel
AUG 2011
5-1
5
Configuring TCP/IP
3.
Double-lick the Network and Dial-up Connections icon to display the Network and Dial-up
Connections window:
Figure 5-2: Network and Dial-up Connections
In the steps that follow, a connection number like 1, 2, 3, etc., is a reference that is displayed on
computers with multiple network interfaces. Computers with only one network interface may only
see the label: Local Area Connection.
4.
Click Local Area Connection number. The value of number varies from system to system. The
Local Area Connection number Status window is displayed:
Figure 5-3: Local Area Connection
5-2
AUG 2011
Configuring TCP/IP
5.
5
Click Properties. Information like the following window is displayed:
Figure 5-4: Properties
6.
If Internet Protocol (TCP/IP) is in the list of components, TCP/IP is installed. You can skip to
Step 10.
Figure 5-5: Select Network Connection Type
If Internet Protocol (TCP/IP) is not in the list, click Install. The Select Network Compoennt Type
window is displayed.
AUG 2011
5-3
5
Configuring TCP/IP
7.
Click Protocol on the Select Network Component type window and click Add. The Select
Network Protocol window is displayed:
Figure 5-6: Select Network Protocol
You might have to use the scroll bar to locate the Internet Protocol (TCP/IP) setting.
8.
9.
10.
11.
Click Internet Protocol (TCP/IP).
Click OK. The local Area Connection Number Properties window is re-displayed.
Be sure the box next to Internet Protocol (TCP/IP) is checked.
Click Properties. The Internet Protocol (TCP/IP) Properties window is displayed.
Figure 5-7: Internet Protocol (TCP/IP) Properties
5-4
AUG 2011
Configuring TCP/IP
5
12. Be sure Obtain IP address automatically and Obtain DNS server address automatically are
selected.
13. Click OK to accept the TCP/IP settings.
14. Click Close to close the Local Area Connection number Properties window.
15. Click OK.
16. If prompted to restart the computer, click OK again.
Configuring TCP/IP in Windows XP
1.
On the Windows desktop, click Start to display the Start window:
Figure 5-8: Windows XP Start Window
AUG 2011
5-5
5
Configuring TCP/IP
2.
Click Control Panel to display the Control Panel window. The display varies, depending on
your Windows XP view options. If the display is Category view as shown in Figure 5-9, continue
with Step 3. Otherwise, skip to Step 5.
Figure 5-9: Control Panel
3.
Click Network and Internet Connections to display the Network and Internet Connections
window:
Figure 5-10: Network and Internet Connections
5-6
AUG 2011
Configuring TCP/IP
4.
5.
5
Click Network Connections. Skip to Step 6.
If a classic view like Figure 5-11 is displayed, double-click Network Connections to display the
LAN or High-speed Internet connections.
Figure 5-11: Control Panel Classic View
6.
Right-click the Local Area Connection. If more than one connection is displayed, select the
one for your network interface.
Figure 5-12: Network Connections
AUG 2011
5-7
5
Configuring TCP/IP
7.
Select Properties from the pop-up menu to display the Local Area Connection Properties
window:
Figure 5-13: Local Area Connection Properties
8.
9.
On the Local Area Connection Properties window, select Internet Protocol (TCP/IP) if it is not
selected.
Click Properties to display the Internet Protocol (TCP/IP) Properties window.
Figure 5-14: Internet Protocol (TCP/IP) Properties
10. Be sure Obtain IP address automatically and Obtain DNS server address automatically are
selected.
11. Click OK to close the TCP/IP Properties window.
5-8
AUG 2011
Troubleshooting
6
Chapter6: Troubleshooting
Power

Verify the AC power adapter is properly plugged into the electrical outlet and into the Desktop
CPE.

Plug a lamp into the outlet to ensure the outlet is receiving power.
A Computer Cannot Log On to the CPE
Disconnect and reconnect the Ethernet cable to the CPE unit and the computer.
Cannot Connect to the Internet

Check the Desktop CPE connection status from the web interface, refer to the Connection Status
section to verify the connection status.

If the Desktop CPE connection is down, and the gateway has not received an IP for 5 minutes to
10 minutes:
− Re-Run the Setup Wizard.
− If the Setup Wizard does not help, then reset the Desktop CPE using the reset button.
Additional Troubleshooting Help
Contact your service provider for additional help.
AUG 2011
6-1
Important Safety and Legal Information
7
Chapter 7: Important Safety and Legal
Information
Your Nokia Siemens Networks WiMAX Wireless Broadband Gateway is designed and tested to
comply with a number of national and international standards and guidelines regarding human
exposure to RF electromagnetic energy. Please see the Regulatory Guide included in the device
packaging.
AUG 2011
7-1
68010072027
Copyright © 2011 Nokia Siemens Networks. All rights reserved.
Nokia is a registered trademark of Nokia Corporation, Siemens is a registered trademark
of Siemens AG. The wave logo is a trademark of Nokia Siemens Networks Oy.
Other company and product names mentioned in this document may be trademarks of
their respective owners, and they are mentioned for identification purposes only.
Nokia Siemens Networks Corporation, Karaportti 3, FI-02610 ESPOO, Finland