MIO-3260 Intel

®

Atom

TM

E3825 & Celeron

®

N2930 Pico-ITX

SBC, with DDR3L, 18/24-bit LVDS, VGA, DP/HDMI, GbE, Fullsize Mini PCIe, 4 USB, 2 COM, SMBus, I2C, mSATA & MIOe

Startup Manual

Packing List

Before you begin installing your card, please make sure that the following items have been shipped:

1. 1 x MIO-3260 SBC

2. 1 x Startup Manual

3. 1 x SATA cable

4. 1 x Power cable*

P/N: 1700006291

P/N: 1700023340-01

5. 1 x Inverter and SATA power cable*

6. 1 x VGA cable*

P/N: 1700023339-01

P/N: 1700023341-01

7. 2 x USB cables* P/N: 1700019000/

1700002172

8. 1 x LAN cable*

9. 1 x Audio cable*

10. 1 x COM cable*

11. 1 x Heatsink

P/N: 1700019001

P/N: 1700019584

P/N: 1701200220

P/N: 1960063455T001

12. Screw & stud pack (2 x screws P/N: 9666226200E/ for Mini PCIe, 4 x M3 studs and 9666226300E* screws for heatsink

* Only for MIO-3260C-S8A1E

If any of these items is missing or damaged, please contact your distributor or sales representative immediately.

Note 1: For detailed contents of MIO-3260, please refer to information on the support web site: http:// support.advantech.com.tw/.

Note 2: Acrobat Reader is required to view any PDF file. Acrobat Reader can be downloaded at: http://get.adobe.com/reader/ (Acrobat is a trademark of Adobe)

For more information on this and other Advantech products, please visit our website at: http://www.advantech.com

http://www.advantech.com/eplatform

For technical support and service, please visit our support website at: http://service.advantech.com.tw/support/

This manual is for the MIO-3260 Series.

Part No. 2006326000

Printed in China

1st Edition

April 2015

Optional Accessories

• Heat spreader (99.5 x 70.5 x 15.7 mm)

P/N: 1960065074N001

• MIO-3260 Evaluation Board

P/N: MIOE-DB2100-00A1E

• LAN w/LED cable for MIO-3260C

P/N: 1700024079-01

Specifications

General

• CPU: Intel ® Atom™ E3825/ Celeron ® N2930

• System Memory: 1 x 204-pin SODIMM socket DDR3L

1333 MHz (N2930) / 1066 MHz (E3825), up to 8 GB

• L2 Catch: 2 MB (N2930) / 1 MB (E3825)

• BIOS: AMI EFI 16 Mbit Flash ROM

• Watchdog Timer: 255 level interval timer

Battery: Lithium 3 V/210 mAH

Note: How to clear CMOS (follow steps below):

1. Turn off system power.

2. Unplug CR2032 battery cable on BH1.

3. Wait for 15 sec or short BH1 pin1-2.

4. Connect battery cable on BH1.

5. Turn on system power.

• Serial ATA: One SATA II interface, up to 300 MB/s

• Expansion Interface:

- 1 x Full-size Mini PCIe (Supports mSATA or USB interface module)

- 1 x MIOe

- 2 x 64pin connectors

MIOe Expansion Slot

• Interface: USB3.0, SMBus, LPC, 2 x PCIe x1, HD Audio

Line-out, DisplayPort or HDMI supported by request, +5

Vsb/+12 Vsb power, Power On, Reset

• Total peripheral power supply output: 5 V @ 3 A for

CPU board and MI/O Extension module in total, 12 V @ 2

A for MI/O Extension module

64-pin Expansion Connectors

• 64-pin connecter A: 12V DC input, Inverter, VGA, 2 x

USB2.0, 1GbE w/ LED

• 64-pin connecter B: SMBus, I2C, Power button, Reset button, HDD/Power LED, 2 x USB2.0, 8-bit GPIO, HD

Audio Line in, Line out, Mic in, 2 x RS-232/422/485

MIO-3260 Startup Manual 1

Specifications (Cont. )

Display

• Controller: Intel® SoC N2930 / E3825, DirectX 11 and

OpenGL3.0 support for VGA, DP or HDMI display output

Chrontel CH7511 for 18/24 bit LVDS display output

• Output Interfaces:

- VGA: 2560 x 1600 at 60 Hz

- LVDS: Single channel 18/24-bit LVDS, up to

1400 x 900 at 60 MHz

- DP/HDMI: 2560 x 1600 at 60 Hz

- Dual Independent Display: LVDS+VGA or LVDS+DP/

DMI or VGA+DP/HDMI*

* DP/HDMI is from MIOe and HDMI supported by request

Ethernet Interface

• Speed: 10/100/1000 Mbps

• Controller: Intel ® I210

Mechanical and Environmental

• Dimensions (L x W): 100 x 72 mm (3.9 x 2.8 inches)

Mechanical Drawings are on page 4 - 6.

• Power Requirement: Single +12 V ± 10% DC power input

• Power Consumption (with 8 GB memory):

- Idle mode:

MIO-3260L-S3A1E(E3825): 4.47 W

MIO-3260L-S8A1E(N2930): 5.08 W

MIO-3260C-S8A1E(N2930): 4.22 W

- Max. load:

MIO-3260L-S3A1E(E3825): 7.13 W

MIO-3260L-S8A1E(N2930): 9.73 W

MIO-3260C-S8A1E(N2930): 8.71 W

• Operating Temperature: 0 ~ 60 °C (32 ~ 140 °F)

• Weight: 0.37 kg, reference weight of total package

Jumpers and Connectors

The board has a number of jumpers that allow you to configure your system to suit your application. The table below lists the function of each of the jumpers and connectors.

Jumpers

Label

J1

J2

Function

LCD Power / Auto Power on

Mini PCIE / mSATA Select

Connectors

Label Function

CN4 64Pin Connector A

CN5

CN6

64Pin Connector B

DDR3L SO-DIMM

CN7

CN8

12V Power Input*

Inverter Power Output/Internal SATA Power*

2 MIO-3260 Startup Manual

Jumpers and Connectors (Cont.)

CN9

CN10

CN11

CN11_1

VGA*

2 x USB 2.0*

Gigabit Ethernet*

Gigabit Ethernet with LED**

CN14

CN16

SATA

Mini PCIE/mSATA

CN29 MIOe

CN31 18/24-bit LVDS panel

*Only for MIO-3260C-S8A1E

**Supported by request

Jumper Settings

J1: LCD Power / Auto Power On

Setting Function

(1-2) +5 V

(3-4)*

(5-6)*

+3.3 V

Auto Power On

* Default

J2: Mini PCIE/ mSATA Select

Setting Function

(Close)*

(Open)

* Default

Mini PCIE mSATA

Caution! The computer is provided with a battery-powered real-time clock circuit. There is a danger of explosion if battery is incorrectly replaced. Replace only with same or equivalent type recommended by the manufacturer. Discard used batteries according to manufacturer’s instructions

.

-

MIO-3260 Connector Locations

18/24-bit

LVDS

DDR3L SO-DIMM Socket

Figure 1: MIO-3260 Connecter Location (Top Side)

64-Pin Connector B

HDD LED, Power LED, Power button, SMBus, I2C, 2xUSB2.0,

8-bit GPIO, HD Audio Line in/out/mic in, 2xRS-232/422/485

MIOe

DP/HDMI,

USB3.0/2.0, 2 x PCIex1,

SMBus,

LPC, 12V/5V power,

HD Audio Line out.

Power on, Reset

SATA

64-Pin Connector A

12V DC in, inverter, VGA ,2 USB2.0, GbE w/ LED

Figure 2: MIO-3260L Connecter Location (Bottom Side)

Full size Mini

PCIe or mSATA

MIO-3260 Startup Manual 3

MIO-3260 Connector Locations (Cont.)

MIO-3260C-S8A1E

2xRS-232/422/485

HD Audio Line in/out/mic in 2xUSB2.0

HDD LED, Power LED, Power button,

SMBus, I2C, 8-bit GPIO,

MIOe

DP/HDMI,

USB3.0/2.0, 2 x PCIex1,

SMBus,

LPC, 12V/5V power,

HD Audio Line out.

Power on, Reset

SATA

Full size Mini

PCIe or mSATA

GbE 2 USB2.0

VGA Inverter &

SATA power

12V DC input

Figure 3: MIO-3260C Connecter Location (Bottom Side)

4 MIO-3260 Startup Manual

MIO-3260 Mechanical Drawing

Figure 4: MIO-3260 Mechanical Drawing (Top View)

Unit: mm

Unit: mm

Figure 5: MIO-3260L Mechanical Drawing (Bottom View)

MIO-3260 Startup Manual 5

MIO-3260 Mechanical Drawing (Cont.)

Figure 6: MIO-3260C Mechanical Drawing (Bottom View)

Unit: mm

Figure 7: MIO-3260 Mechanical Drawing (Side View with Heatsink)

Unit: mm

Unit: mm

Figure 8: MIO-3260 Mechanical Drawing (Side View with Heatspreader)

6 MIO-3260 Startup Manual

Quick Installation Guide

1. A heatsink is in the white box, please take it out and remove the releasing paper from the thermal pads.

Removing the releasing paper

2. There are also four screws inside the white box, please install the DRAM in the SO-DIMM socket first, then screw the heatsink into place as per illustration below:

MIO-3260 Startup Manual 7