Craftsman 610.24610 Operating instructions

User Instructions
ICR
FTSM
®
TRACTOR LIFT
Model Number 610.24610
Provides access to mower deck for easy
cleaning and service
Fits all 1985 through current models
of CRAFTSMAN front engine tractors
and zero turn mowers
•
Adjustable
•
Extra heavy duty steel construction
Assemble
Pending
arms for greater versatility
If you read and follow these instructions,
assembled in approximately 20 minutes
•
Patent
this product can be
unit on cardboard to avoid scratches or damage to parts
Can easily be assembled
by one person
All fasteners for this Tractor Lift can be purchased at Sears or any
hardware store
If there are any missing
parts, or if you have any
questions on assembly,
operation, maintenance
or safety, please call
1-800-652-2321
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
Visit our Craftsman website: www.sears.com/craftsman
Made
inChina
310041-REV
C 1/09
SAFETY
WARNINGS
INSTRUCTIONS
• Always check to ensure stabilizers are properly in place and
stabilizer latches are engaged before starting any work on tractor.
Be sure to read and follow all safety instructions and
warnings. Failure to follow these instructions may result in
damage to the product and/or serious personal injury.
• Read and understand all safety and operating instructions
before using the tractor lift. Never allow anyone unfamiliar
with these instructions to use the tractor lift.
Danger of serious personal injury exists. Serious
injury can occur when using a lifting device.
Never attempt to ride any vehicle
• Read and understand all safety and operating instructions
provided by the tractor's manufacturer
before using tractor
• Never lay under the tractor or mowing
• When
using lift, keep all bystanders,
lift.
deck.
including
up or down the tractor
Do not climb onto tractor while tractor
• This tractor lift must be only used for lifting and lowering
and from a level and stable surface.
position.
place wheel
to
Always raise and lower tractor lift in a controlled fashion; do not
allow the tractor to drop too quickly, damage could occur.
Make sure lifting arms are aligned and set to the proper distance
so that the equipment being loaded is well balanced on the lift.
• Do not attempt to lift the front and back of the tractor
time.
• Do not use tractor lift as an automotive
which it is not intended or designed.
at the same
lift, or for any other use for
Do not remove warning
Before each use, always check for any worn, loose, or
damaged parts on the tractor lift. If any damage is present,
DO NOT USE THE TRACTOR
LIFT.
Periodically check the fasteners
tight and in place.
• Do not attempt to lift or lower any power equipment
running.
Keep lift surface clean by occasionally
any mild detergent.
blades while using tractor
while motor is
lift.
• Always disconnect spark plug wire from tractor before beginning
any work on tractor.
of the tractor lift - 275 Ibs.
apart
decals from product.
• If tractor lift is bowing while lifting or lowering your tractor, which
indicates an overload condition, remove the tractor immediately.
• Do not exceed the rated capacity
lift.
away.
• Never use in wet conditions.
• Never engage
is in the elevated
When working on the front of the tractor always
chocks in back of the rear wheels/tires.
children,
personal
to make sure they are still
cleaning
with water and
Do not add to or try to modify the tractor lift in any way.
Any modifications
will void any warranties.
Failure to abide by the warnings and read the safety instructions may
result in loss of load, damage to lift and/or property, serious personal
and/or fatal injury.
• Failure to follow these warnings may result in property
damage and/or serious bodily injury.
FOR MISSING PARTS, Call 1-800-652-2321, Monday - Friday, 8 a.m.- 5 p.m.E.S.T.
Page 2.
Carton Contents
.................................
..............
10
REF NO
1
2
3
4
QTY
1
1
1
2
PART NUMBER
510016
510023
510034
51008
DESCRIPTION
Frame Assembly
Handle, Top
Handle, Bottom
Lift Tube Assembly
OPERATION
Tractor Lift can be used out of the box on all Craftsman tractors
with bumpers or brush guards. Tractor Lift mounting hardware is
provided if your tractor does not have a bumper or brush guard.
TOOLS REQUIRED
FOR ASSEMBLY
9/16" Wrench and/or Socket
Adjustable wrench
REF NO
6
10
11
QTY
1
2
1
1
PART NUMBER
510052
410133
310037
310041
DESCRIPTION
Bar, Lifting
Bracket, Tractor
Hardware Bag
Assembly Manual
MAINTENANCE
Store unit in a clean dry place.
Recommended
Before each
•
Always
•
Always
•
Always
tire pressure
- 30 PSI.
use:
check tire pressure.
inspect unit for damage.
check fasteners for tightness.
FOR MISSING PARTS, Call 1-800-652-2321, Monday - Friday, 8 a.m.- 5 p.m.E.S.T.
Page 3.
Hardware
Contents
¢.....--
28
L..._
24
23
25
29
(O )
t'--
L___
22
REF NO
QT'r"
3
23
24
25
5
26
4
PARTNUMBER
27
DESCRIPTION
31
32
REF NO
28
QTY
3/8" Split Lock Washer
3/8" USS Flat Washer
29
31
8
1
310055
310063
318"-16 x 1-114" Hex Bolt
1t2"-13 Hex Nut
310062
3/8"-1 6 He;,( Nut
32
1
310074
112" USS Flat Washer
300082
Hairpin
310061
3/8"-1 6 ['¢;/Ioc Hex Nut
310051
318"-1 6 x 2-3/4"
310072
310073
Hex Bolt
PARTNUMBER
310054
26
Cotter
FOR MISSING PARTS, Ca111-800-652-2321, Monday-Friday,
Page 4.
8 a.m.-5
p.m.E.S.T.
318"-16 x 1-1/2" Self-th read Bolt
Setting up Lift Mounting
Hardware
Tractor Lift can be used out of the box on all Craftsman tractors with bumpers or brush guards. For tractors without bumper or brush guard,
Tractor Lift mounting hardware is provided. Follow the steps below:
31
6
32
IlXll
Front
Remove,
add washer
replace.
6
( 24 ),
Rear
Remove existing bolt "X" and set aside. If tractor does not
have this bolt, use supplied 3/8" x 1-1/4" bolt and 3/8" nyloc nut.
Place lifting bar ( 6 ) under rear tractor hitch and slide threaded
stud through hole.
Insert bolt ( 29 ) through inside front hole of frame, through
tractor bracket ( 7 ) and secure with nyloc nut ( 27 ).
Secure in place with flat washer ( 32 ) and hex nut ( 31 ).
Add flat washer ( 24 ) under head of bolt removed in earlier
step and reinsert through tractor mounting bar and tighten.
For LT1000 & LT2000 series tractors, use self-thread
( 28 ) in place of bolt ( 29 ) and nut ( 27 ).
bolts
Slide lifting bar ( 6 ) through cut-out in tractor brackets.
Pin lifting bar in place with one hairpin cotter ( 26 ) on each
side, inside of tractor brackets ( 7 ).
FOR MISSING PARTS, Call 1-800-652-2321, Monday - Friday, 8 a.m.- 5 p.m.E.S.T.
Page 5.
Assemble
Tractor Lift
Attach Lift Tubes to Angle Frame
Lift tubes come pre-assembled.
Attach lift tube assemblies
washers ( 23 ) and hex nuts ( 25 ).
Secure rear of lift tube assembly
nuts ( 25 ).
Note: Over-tightening
( 4 ) to angle frame ( 1 ) using bolts ( 22 ), flat washers ( 24 ), split lock
( 4 ) to angle frame ( 1 ) using bolts ( 29 ), flat washers
( 24 ), split lock washers ( 23 ) and hex
receiver bolts ( 22 ) could cause damage to lift tubes ( 4 ).
Determining
Craftsman
Front of Craftsman
Tractor
the width between
lift tubes.
Brush guard / Bumper
Zero
Mower
4
5
Note: The higher the lift tube extensions (5)
are positioned, the harder the tractor will be to lift.
Settings:
A.
Push Mower
B.
Brush guard / Bumper
C.
Craftsman Tractor
D.
Front of Craftsman Zero Turn
FOR MISSING PARTS, Call 1-800-652-2321, Monday - Friday, 8 a.m.- 5 p.m.E.S.T.
Page 6.
Assemble
Tractor Lift
Attach Handle to Angle Frame
Step 1.
Attach handle bottom ( 3 ) to angle frame ( 1 ) using hex bolt ( 22 ),
flat washer ( 24 ), split lock washer ( 23 ) and hex nut (25).
Step 2.
Insert ring grip pin ( 30 ), as shown.
Step 3.
Insert handle top ( 2 ) into handle bottom ( 3 ). Secure with hex
bolts ( 29 ) and split lock washer ( 23 ).
24
2
FOR MISSING PARTS, Call 1-800-652-2321, Monday - Friday, 8 a.m.- 5 p.m.E.S.T.
Page 7.
Using the Tractor Lift
Center Tractor Lift in front of tractor.
Check that both stabilizers
Always check that stabilizer
after lifting tractor.
latches are in the locked position
are resting on the ground as shown.
Align lift tube claws with lifting bar or bumper/brush
roll Tractor Lift forward to engage.
Check that claws are securely
bumper/brush guard.
guard and
Stabilizer latches must be flipped to the unlocked position
before lowering tractor.
hooked under the lifting bar or
Place foot onto foot bar and apply continuous forward pressure
with foot while pulling down on tractor lift handle.
Once lifted, the weight of the tractor will automatically
handle down into the correct position.
force the
Locked
FOR MISSING PARTS, Ca111-800-652-2321, Monday-Friday,
Page 8.
8 a.m.-5
Unlocked
p.m.E.S.T.
Repair Parts
List
MODEL
- 610.246101_"
NUMBER
7
_
- ' _:I'_
!
26
11
10
29
25
REF. NO.
1
3
4
5
6
7
8R
8L
9
10
11
20
21
22
PART NO.
REF. NO.
PART NO.
AMT.
510012
1
Fra me
23
310072
7
510022
510032
1
1
Handle, Top
Handle, Bottom
24
310073
7
3/8" Split Lock Washer
3/8" USS Flat Washer
25
310062
5
318"-16 Hex Nut
51004
Lift Tube
26
300082
51007
Receiver Tube
510052
410133
AMT.
1
DESCRIPTION
DESCR I PTI ON
Hairpin Cotter .148 Wire, 3-5/16"
310061
4
Bar, Lifting
Bracket, Tractor
28
310054
2
318"-16 Nylok Hex Nut
**'3t8"-16 x 1-1t2" Self-thread
29
310055
8
**'318"-16
310081
3
x t-114" Hex Bolt GR5
510061
1
Stabilizer,
Right
30
510062
1
Stabilizer,
Left
31
310063
1
Pin, Quick-Release
112"-13 Hex Nut
310011
2
Wheel, 10" x 518"
32
310074
1
1/2" USS Flat Washer
310037
1
Hardware
Bag
37
310181
2
Grip, Handle
310041
1
Assembly
Manual
38
310221
2
Plug, 1" Tube
310071
300081
2
2
Washer, 5t8" SAE
Cotter Pin 1t8" x 1-112"
39
31026
1
Pad, Scuff
40
310341
2
Retaining
310051
3
3/8"-16
41
31041
2
Latch, Safety
x 2-314" Hex Bolt G R5
***Not Shown, see hardware bag contents.
FOR MISSING PARTS, Call 1-800-652-2321, Monday - Friday, 8 a.m.- 5 p.m. E.S.T.
Page 9.
Bolt
Ring, 5/8"
CRAFTSMAN
THREE YEAR LIMITED WARRANTY
If this Craftsman product fails due to a manufacturer's defect within three years from the date of purchase,
any Sears store or other Craftsman outlet in the United States for free replacement.
return it to
This warranty does not provide product replacement due to wearing off or fading of product paint, or wearing out or
failure of product tires or wheels.
This warranty is void if this product is ever used for commercial or rental purposes.
This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state.
Sears, Roebuck and Co., Hoffman Estates, IL 60179.
PRODUCT
RECORD
In the space below record the model number and
purchase date of your cart. The model number can
be found on the front cover of the user guide.
ORDERING
INFORMATION
After the three year warranty period all parts may
be ordered by calling Sears Service at
1-800-4MY-HOME
(1-800-469-4663).
When ordering repair parts, always give the
following information:
Model Number
Purchase
Date
Keep this booklet and your Sears receipt in a safe
place for future reference.
NOTES
Product Model NumberPart Number - *
Part Description - *
*Found on the repair part list. Reference
page 9.
Your Home
For expert troubleshooting
and home solutions advice:
www.managemyhome.com
For repair - in your home - of all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
For the replacement parts, accessories and
owner's manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
1-800-4-MY-HOME
Call anytime,
®
(1-800-469-4663)
day or night (U.S.A. and Canada)
www.sears.com
www.sears.ca
Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call anytime for the location of your nearest
Sears Parts & Repair Service
1-800-488-1222
(U.S.A.)
1-800-469-4663
To purchase a protection agreement
on a product serviced by Sears:
(U.S.A.)
Para pedir servicio de reparaci6n
a domicilio, y para ordenar piezas:
1-888-SU-HOGAR
1-800-361-6665
(Canada)
Au Canada pour service
en fran£ais:
1-800-LE-FOYER
®
Trademark
/ TMTrademark
/ SMService
M°
(1-800-533-6937)
www.sears.ca
(1-888-784-6427)
® Registered
(Canada)
www.sears.ca
www.sears.com
1-800-827-6655
Center
Mark of Sears Brands,
® Marca Registrada / TM Marca de Fabrica / SM Marca de Servicio
MC Marque de commerce / MD Marque depos6e de Sears Brands,
LLC
de Sears Brands,
LLC
LLC
© Sears
Brands,
LLC